GEOPOINT BOX - ServiceDocs.Com
Contents
1. Close 29 Setup by MyTrack Software Position Data Recording To set a data position recording connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup General SMS Recordings GPS Recordings Rate Distance Erase previous recordings Erase All SMS Destination Nr 1 393401234567 SMS Destination Nr 2 SMS Destination Nr 3 SMS Destination Nr 4 30 Setup by MyTrack Software Update of the Tracker Firmware Version To update the tracker connect the tracker to the provided software and access the info window by selecting Info from Remote Unit menu Tracker Information Le 2 Tracker Information Information Information GEOPOINT GEOPOINT BOX BOX Geo Gloria Geo Gloria Serial Number XCUTI3001 Serial Number XCUTI3001 Firmware Release 1 04 Firmware Release 1 04 Year 2007 Year Memory Memory Status Ready A new window is opened for update file selection The 3 LEDs remain continuously ON during tracker firmware update Wait until the update is completed this occurs when the tracker is turned off A If the tracker to be updated is connected with GSM GPRS network be sure that the GSM GPRS network signal level is high A If the tracker to be updated is connected by a USB cable do not remove the cable during the update A2. J x f N SEOPOINT BOX PE F3 SCI ALt TRACK ER User Guide GEOPOINT BOX PERSONAL TRACKER User Guide July Edition 2009 Limitation of Liability The Manufacturer reserves the right to modify the devices or the device specifications in this manual without prior notice Any copy of this manual in part or in full whether by photocopy or by other means even of electronic nature without the manufacture giving written authorisation breaches the terms of copyright and is liable to prosecution It is absolutely forbidden to use the device for different uses other than those for which it has been devised for as inferred to in this manual When using the features in this device obey all laws and respect privacy and legitimate rights of others EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN All trademarks in this manual are property of their respective owners The information contained in this manual is for information purposes only is subject to changes without previous notice and cannot be considered binding for the Manufacturer The Manufacturer assumes no responsibility for any errors or incoherence possibly contai
3. Power Save Mode the tracker switches on off automatically to optimize the battery consumption o apter Setup by MyTrack Software Alarm SMS the tracker sends alarm SMS to the preset phone number everytime a status change happens low battery memory full o apter Tracker Management by SMS hapter Setup by MyTrack Software o The tracker can work without the SIM card In this case all functions operating with GSM GPRS network will not be available 11 Use of the Tracker SOS Key By pressing the SOS key for at least 2 seconds for 5 consecutive times every minute an SMS message is immediately sent to the preset phone numbers max of 4 phone numbers This message also contains the current data on the location if the GPS signal has been revealed If there is no GPS signal coverage the last position data will be sent P If no numbers have been set or in the absence of GSM signal every time the SOS key is pressed an acoustic warning signal is emitted esti In the event that there is no network service coverage the alarm functions may not be available Example of the SMS message displayed on the mobile phone with the detected current position data GEO ID GLORIA SOS ALARM P08 45937 9480N 008928 9992E 4LT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone with the last position data detected before the GPS signal loss GEO ID GLORIA SOS ALARM L
4. 008928 8012E 41937 8971N 012928 8012E OK Description 1 enable 45g37 7981N 008g28 8012E latitude and longitude of the first point 41937 8971N 012928 8012E latitude and longitude of the second point NOTE to enable or disable the Geofence function without setting the area sent the wgf command with the first field only Case B Command wgf 1 Reply wgf 1 OK Description 1 enables the function considering the previous defined area 23 Tracker Management by SMS Command Meaning and Values Example wanc Set the Anchor Case A enabling 0 disable 1 enable Command wanc 1 0100 radius 0050 0100 0200 0300 0500 0700 1000 Reply wanc 1 0100 OK 1500 2000 3000 4000 m default radius 0100 Description NOTE to set the tracker current position as area 1 enables center point send the complete wanc command 0100 radius at 100 m containing both enabling and radius fields e g wanc 1 0100 Case B Command wanc 1 0100 NOTE to enable or disable the Anchor function Reply NO VALID CENTER POS without setting the radius send the wanc command m with the first field only In this case the default radius Description or the previously set radius is considered 1 enables 0100 radius at 100 m NO VALID CENTER POS if the center point cannot be detected Case C Command wanc 1 Reply wanc 1 OK Description T enables the function considering the default radius or the previously set rad
5. GSM device able to send receive SMS i e a GSM modem When the tracker is switched ON and there is GSM signal it can receive any SMS command If the tracker receives a correct SMS command an answer is sent to the SMS command sender If the message contains invalid characters the tracker will not reply If it contains invalid values the tracker will reply a message containing COMMAND ERROR All commands start with the letter r reading or w writing Ensure that the SMS commands are written exactly as shown in the table Any change space capital letter small letter could affect the recognition of the command Before enabling the sending of position SMS in cyclic mode wposc ensure EI that the SMS phone number has been programmed 19 Tracker Management by SMS Reading Commands Command Meaning and Values Example rpos Read instantaneous GPS position data Command rpos Reply A The tracker can reply in 3 different ways POS 41937 8283N 012928 8191E ALT 0262m DIR 023g SPEED 0050km h A POS position data GPS position in real SAT 09 07 05 26 15 56 time Reply B B LAST POS lt position data gt no GPS signal The LAST POS 45937 8283N reply message contains the last detected GPS data 008928 8191E ALT 0262m SW DIR 023g SPEED 0050km h C POS NO GPS DATA from the tracker switching SAT 09 07 05 26 15 56 on the GPS signal has not been detected Reply C i POS NO G
6. RECORDING ADDRESS Book DISCONNECT CENTER Pause FORWARD DECREASE THE RECORDING SPEED Power Save Mode The Power Save Mode allows for optimal management of the battery tracker It is possible to set the tracker automatic switching on off according to specific use requirements There are three Power Save Modes programmable by means of the provided software except for Cyclic Position SMS which is programmable by SMS command too After Power Save Mode enabling the tracker will switch off automatically 2 minutes after tracker disconnection by the provided software WITH MOTION MOTION OFF ON NO MOTION FOR A PRESET TIME NO DATA EXCHANGE 26 Setup by MyTrack Software WITH CYCLIC POSITION SMS OFF ON CYCLIC POSITION SMS SENDING SMS SENT A Before using this mode enable and set the Cyclic Position SMS function with SMS rate gt 5 minutes During the automatic switching on if the tracker is connected by the provided software the automatic switching off will be carried out after position SMS sending after carrying out all the preset operations and 2 minutes after tracker disconnection WITH CYCLIC GPRS CONNECTION OFF ON CYCLIC GPRS CONNECTION A Before using this mode enable and set the Cyclic GPRS Connection function with rate gt 5 minutes The tracker will switch off automatically after successfull GPRS connection and after carrying out all the preset operations If after two tries the GPRS connecti
7. SMS Tracker Management by SMS Position Request It is possible to ask for the tracker position by means of an SMS command After receiving the SMS command the tracker sends a message containing the position data to the phone number which sent the command To know the tracker position in real time send the following command POS For further details refer to the paragraph Reading and Writing SMS Commands Automatic Position Sending The tracker can send its own position at a programmable rate The automatic position sending can be carried out in two different modes by SMS by GPRS connection CYCLIC POSITION SMS The tracker can send an SMS message at intervals containing all the information on its current position This function is useful for monitoring the tracker motion at a distance by a mobile phone To use this function it is necessary to set using the provided software the phone number where the position messages will be sent setthe rate for the cyclic position SMS using the provided software or sending an SMS command enable the function using the provided software or sending an SMS command 14 Tracker Management by SMS CYCLIC GPRS CONNECTION The cyclic GPRS connection allows to connect the tracker automatically at a programmed rate for the continuous position updating At the programmed rate the tracker will be connected only for the time needed for sending the position point This function is very u
8. Sec If the battery is not inserted within 30 seconds the date and hour settings will be ERASED To insert the SIM card remove the back cover and lifting out the battery Preliminary Procedures How to Charge the Battery Before using the tracker for the first time the battery must be completely charged Before charging check that the network electrical supply corresponds to that of the battery charger Do not exceed the network voltage indicated on the battery charger A Use only batteries and battery chargers with the following features Battery model ABL 6C Li ion Battery charger model ZDO50050EU Car charger model ESC 004 The manufacturing company is not liable for any damage to the tracker due to the use of accessories different from those expressly indicated Do not leave the tracker in particularly hot or cold environments during the battery charging Keep the tracker between 10 C and 40 C environmental temperature gt When the battery is almost discharged the tracker if ON emits an acoustic warning every minute Use of the Tracker Use of the Tracker LED Indicators The LED indicators on the front part of the device shows the status of the main functions of the tracker At tracker switching on off the 3 LEDs will light up together at the same time for 1 second and an acoustic signal will be emitted GEOPOINT GPS Signal OFF tracker off or GPS receiver off e ON
9. To perform the update it is necessary to connect the provided battery charger to the tracker 31 Maintenance Maintenance The tracker and relevant accessories must be handled with care Read the following instructions carefully Clean the tracker with a soft cloth avoiding the use of corosive chemical products solvents or aggressive detergents Do not paint the tracker Do not swallow the accessories or small components of the tracker Avoid blows to the tracker which could internally damage the product Do not open the tracker in any way differently from the way indicated in the manual Do not wet the tracker Humidity condensation rain or any other liquids containing mineral substances could damage the electronic circuits In the event of contact with liquids remove the battery and leave the tracker to dry Do not use or leave the tracker in particularly hot environments High temperatures could damage the electronic circuits the battery and the plastic parts of the tracker Do not use or leave the tracker in particularly cold environments Low temperatures could cause damage to the electronic circuit boards of the tracker Do not use or leave the tracker in particularly dirty or dusty environments the tracker could get damaged 32 Technical Features Technical Features GPS receiver SiRFstarlll 20 channels GSM frequencies 850 900 1800 1900 MHz Data memory 512kB
10. has purchased the Product provided that the same Product has been intended for sale in that country by the Manufacturer However if the user has purchased the Product in a member state of the European Union Iceland Norway Switzerland or Turkey and such Product was originally intended by the Manufacturer for sale in one of these countries this Limited Warranty is valid and enforceable in all of these above listed countries Some limitations to the warranty service may apply because of country specific elements in the Products Warranty Period The warranty period starts at the time of Product s original purchase by the first end user The Product may consist of several different parts and different parts may be covered by a different warranty period The different Warranty Periods are 24 months for the device 6 months for the following consumable parts and accessories battery chargers device cover e 90 days for the media on which any software is provided e g CD ROM DVD As far as national laws permit the warranty period will not be extended or renewed or otherwise affected due to subsequent resale repair or replacement of the Product authorized by the Manufacturer 34 5 on hi N 3 GII m Soas sa ja M DL EDI yhty ssa ae En ol CI ARIE w f E Distributed by O Cte international www cte it
11. waiting GPS signal e blinks every sec poor signal level 2D FIX blinks every 4 sec high signal level 3D FIX Battery OFF tracker off or battery completely charged e blinks every 2 3 sec battery discharged ON battery charging in progress GSM Network e e e e 10 OFF tracker off or connected to USB port blinks every sec network search in progress blinks every 4 sec sufficient signal strength 2 blinks every 4 sec GSM GPRS data communication in progress Use of the Tracker Tracker Function Description Refer to SOS key the tracker sends an alarm message chapter Use of the Tracker Position Request the tracker sends an SMS containing chapter Tracker Management by SMS its position to the phone number which requested this data Automatic Position Sending the tracker sends automatically its position by SMS or by GPRS connection o hapter Tracker Management by SMS Position Data Recording the tracker records its position data to review the track afterwords o apter Use of the Tracker apter Setup by MyTrack Software o Geofence the tracker sends an alarm SMS to the preset phone number everytime it exits or ri enters in a preset rectangular area o hapter Tracker Management by SMS Anchor the tracker sends an alarm SMS to the preset phone number everytime it exits or ri enters in a preset circular area o apter Tracker Management by SMS
12. 0 1000 Description 1500 2000 3000 4000 m 1 enabled 0100 radius at 100 m 21 Tracker Management by SMS Writing Commands Command Meaning and Values Example wposc Set the cyclic position SMS in text format and the Case A relevant power save mode Command wposc 1 01 0 enabling 0 disable 1 enable Reply wposc 1 01 0 OK rate 01 99 minutes Description power save mode O disable 1 enable 1 enables the cyclic position SMS NOTE the power save mode works only with 01 1 minute rate SMS rate gt 5 minutes O disables the power save mode Never set like this wposc 0 xx 1 i i Case B NOTE to enable or disable only the cyclic position Command wposc 1 SMS send the wposc command with the first Reply wposc 1 OK field only In this case the previously set rate is ats considered Description E 1 enables the cyclic position SMS with the previous set rate wms Set the accelerometer values Command wms 02 10 sensitivity 00 disables sensor 01 maximum Reply wms 02 10 OK 10 minimum Description timeout 01 99 minutes 02 sensitivity level 2 10 10 minutes timeout 22 Tracker Management by SMS Command Meaning and Values Example wgf Set the Geofence Case A status O disable 1 enable Command LAT1 LONG1 LAT2 LONG2z latitude and longitude wgf 1 45g37 7981N 008928 8012E for the 2 points defining the Geofence area 41937 8971N 012928 8012E Reply wgfz1 45937 7981N
13. AST P0 45937 9480N 008928 9992E ALT 0218m 07 04 10 10 09 The SMS message structure of the SOS function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software SOS ALARM Alarm message POS Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm 12 Use of the Tracker Position Data and Events Recording The tracker allows to record e the detected events automatically without setting the recording the position data to review the track afterwords if the recording was previously set The tracker can records approx 14 800 position points and approx 1 900 events When an event occurs the tracker detects it and start to record in the Event LOG The following list shows all the events which can be detected and recorded automatically by the tracker power on off low battery receiving a data call making a GPRS call hanging up a call motion on off GSM network available unavailable GPS signal available unavailable entry exit from Geofence area entry exit from Anchor area firmware update SOS alarm memory erasing roaming on off network GSM provider changing if roaming on The setup of the position points recording can be carried out by means of the provided software refer to the chapter Setup by MyTrack Software 13 Tracker Management by
14. PS DATA NOTE the date and time refer to a SMS sending in case of Reply A Description N N last detected GPS data in case of Reply B 41937 8283N Lat in degree min 012928 8191E Long in degree min 0262m Altitude in m 023g Direction in degree 0050km h Speed in km h 09 Satellites number 07 05 26 Date yymmad 15 56 Time hhmm rposc Read cyclic position SMS setup and power save Command rposc mode status Reply rposc 1 01 0 status 0 disabled 1 enabled Description rate 01 99 minutes 1 enabled cyclic position SMS power save mode O disabled 1 enabled 01 1 minute rate O disabled power save mode 20 Tracker Management by SMS Command Meaning and Values Example rms Read the accelerometer setup values Command rms sensitivity 00 disabled sensor 01 maximum Reply rms 02 10 10 minimum Description timeout 01 99 minutes 02 sensitivity level 2 10 10 minutes timeout rgf Read the Geofence setup Command rgf status O2 disabled 1 enabled Reply LAT1 LONG1 LAT2 LONG2z latitude and rgf 1 45g37 7981N 008g28 8012E longitude of the 2 points which define the Geofence 41937 8971N 012928 8012E area Description 1 enabled 45937 7981N 008928 8012E latitude and longitude of the first point 41937 8971N 012928 8012E latitude and longitude of the second point ranc Read the Anchor setup Command ranc status 0 disabled 1 enabled Reply ranc 1 0100 radius 0050 0100 0200 0300 0500 070
15. bi e phone when the tracker memory is full GEO ID G Examp e of the SMS message disp LORIA MEMORY FULL 07 04 10 10 09 ayed on he mobi e phone when he GPRS network is available GEO ID G Examp e of the SMS message disp LORIA GPRS 0K 07 04 10 10 09 ayed on he mobi e phone when he GPRS network is not available GEO ID GLORIA GPRS 0FE27 04 10 Examp e of the SMS message disp 10 09 ayed on he mobi e phone when here is GPS signal GEO ID G Examp e of the SMS message disp LORIA GPS FIX 0K 07 04 10 10 09 ayed on he mobi e phone when he GPS signal has been lost GEO ID G Examp e of the SMS message disp LORIA NO GPS FIX 07 04 10 10 09 ayed on he mobi e phone when a tracker motion is revealed GEO ID GLORIA MOTION 0N 07 04 10 10 09 Examp e of the SMS message disp ayed on he mobi e phone when a tracker motion stops GEO ID GLORIA MOTION 0FEQ7 04 10 10 09 18 Tracker Management by SMS The SMS message structure of the Alarm SMS function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software LOW BATTERY Alarm message Event date and time yy mm dd hh mm Reading and Writing SMS Commands The SMS commands allows to set or read some tracker settings These messages can be sent by a mobile phone or by a
16. ftware 15 Tracker Management by SMS Example of the SMS message displayed on the mobile phone when the tracker enters the area GEO ID GLORIA ANCHOR ENTER P08 45937 9481N 008928 9992E 4LT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone when the tracker exits the area GEO ID GLORIA ANCHOR EXIT POS 45937 9481N 008928 9992E 4LT 0218m 07 04 10 10 09 The SMS message structure of the Anchor function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software ANCHOR ENTER Alarm message POS Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm Geofence The Geofence function allows to monitor the entry and the exit of the tracker in a pre established area This is a rectangular area and can be programmed by set the area diagonal coordinates by means of the provided software or by means of an SMS command sent by a mobile phone To set the SMS command refer to the paragraph Reading and Writing SMS Commands After having set the parameters of the Geofence function the tracker will send an SMS message of alarm to the preset phone number set by means of the provided software each time it enters exits the pre established area or each time it is switched on outside the pre established area 16 Tracker Management by SMS Examp
17. ius wem Erase all position data recorded in the memory Command wem Reply wem OK 24 Tracker Management by SMS Command Meaning and Values Example wgprs Set the GPRS parameters and start the continuous Case A GPRS connection Command setup O set the GPRS parameters without starting wgprs 0 213 86 89 11 9500 the connection Reply 1 connect with the new parameters IP PORT wgprsz0 213 86 89 11 9500 OK 2 connect with the parameters previously preset Description parameters IP host IP address PORT TCP port NOTE the IP and PORT parameters should be written between commas NOTE if there is no GPRS connection the tracker sends an error SMS containing GPRS ERROR 0 set GPRS parameters without starting the connection 213 86 89 11 host IP address example 9500 TCP port Case B Command wgprs 1 213 86 89 11 9500 Reply wgprsz1 213 86 89 11 9500 OK Description 1 GPRS connection with new parameters 213 86 89 11 host IP address example 9500 TCP port Case C Command wgprs 2 Reply wgprs 2 OK Case D Reply NO GPRS COVERAGE Description NO GPRS COVERAGE if GPRS signal is missing 25 Setup by MyTrack Software Setup by MyTrack Software GEOPOINT INCREASE THE PRINT SETUP PAN PLAY REWIND RECORDING SPEED MYTRACK SETUP CONNECT FoLLow RECORDING SPEED MyTrack mium aaa OPEN Pace SETUP INFORMATION BAR TO SCROLL THE
18. le of SMS message displayed on the mobile phone when the tracker enters the area GEO ID GLORIA GEOFENCE ENTER P0S 45937 9481N 008928 9992E ALT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone when the tracker exits the area GEO ID GLORIA GEOFENCE EXIT P0S 45937 9481N 008928 9992E ALT 0218m 07 04 10 10 09 The SMS message structure of the Geofence function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software GEOFENCE ENTER Alarm message POS lt Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm Alarm SMS The Alarm SMS are alarm messages sent if the function has been enabled by the provided software to a phone number every time that the tracker battery is almost discharged the tracker memory is full the GPRS network is available the GPRS network is not available the GPS signal of the tracker has been lost the GPS signal of the tracker has been restored tracker motion is revealed the tracker motion stops 17 Tracker Management by SMS This function can only be programmed by means of the provided software Examp e of the SMS message disp ayed on he mobi e phone when the tracker battery is almost discharged GEO ID G Examp e of the SMS message disp LORIA LOW BATTERY 07 04 10 10 09 ayed on he mo
19. lowing the tracker management and personal tracking A The GPS receiver and the GSM device work at higher radio frequencies which can be stopped by enclosures containing metal and plastic parts It is suggested to keep the tracker under light clothes as external as possible Examples of shielding materials kevlar carbon fibre some polyurethanic and polyamidic resins especially if black etc Examples of materials which cannot influence the radio waves ABS ABS PC policarbonate etc For further details on tracker use and functions please read carefully the user manual complete version contained in the enclosed CD ROM General Information SEOPONT YELLOW LED GPS RED LED BATTERY GREEN LED GSM SOS KEY USB DC IN Preliminary Procedures Preliminary Procedures Inserting the SIM Card In case of a SIM card prepaid the communication between the tracker and the provided software is made exclusively by SMS text or GPRS network with subscription the communication between the tracker and the provided software is made by SMS text GPRS network or also sending receiving data only if the data number has been activated by the network provider PIN Before inserting the SIM card in the tracker disable the PIN code by means of a mobile phone Inserting a SIM card any SMS message contained in it or which will be received in the future will be deleted and cannot be retriveable
20. ned in this manual Printed in Italy Note for the users of appliances According to the article 13 of the Legislative Decree no 151 dated July 25 2005 Enforcement of the 2002 95 EC and 2003 108 EC directives relavant to the reduction of dangerous substances in electric and electronic applinaces as well as waste disposal the symbol of a crossed dustbin applied on appliances or on their cases means that the product at the end of its life cycle must be disposed in a dedicated location than other waste The user must therefore dispose the aplliance at its end of life in the relevant disposal site for electric and electronic waste or give it back to resellers at the time of purchasing a news equivalent one The correct disposal and consequant start up of a recycling of the unused appliance treatment and final disposal compatible to the enviroment concurs to avoid possible negative effects on the enviroment and health and favours the reusing and or recycling of the parts making the apparatus The abusive disposal of such products done by users is fined according to the present legislation Contents Preliminary Procedures Inserting the SIM Card How to Charge the Battery o o uS Position Request Automatic Position Sending Geofence Alarm SMS Reading and Writing SMS Commands 19 Position Data Recordin Update of the Tracker Firmware Version Technical Features Manufacture
21. non volatile FLASH Porta di comunicazione no 1 USB Sensor no 1 for accelerometer Dimension Weight 74 x 74 x 23 mm 120 gr Battery model ABL 6C Li ion 3 7V 1000mAh Battery charger model ZDO50050EU input 100VAC 240V 50 60Hz 0 15A output 5VDC 500mA Car charger model ESC 004 input 13 6VDC output 5VDC 500mA Conformity CE mark CONDITION BATTERY LIFE Standby mode with motion sensor active 10 days Tracking SMS every minute GPS always on 9 hours Tracking SMS every 5 minutes GPS with hotstart 4 days Continuous tracking 2 hours Data connection with GPS system continuously active 2 hours Position data recording every minute 37 hours Tracker not in use 2 days Tracker in communication on GSM network 4 hours 33 Manufacturer s Limited Warranty Manufacturer s Limited Warranty This warranty does not limit the user s statutory rights under applicable national laws relating to the sale of consumer products During the warranty period the Manufacturer or Manufacturer authorized service company will in a commercially reasonable time remedy defects in materials design and workmanship free of charge by repairing The Manufacturer will in accordance with this Limited Warranty unless otherwise required by law remedy defects by repair or should the Manufacturer in its discretion deem it necessary replace the Product This Limited Warranty is only valid and enforceable in the country where the user
22. on is failed the tracker will switch off automatically 27 Setup by MyTrack Software To a set a Power Save Mode connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup General SMS Recordings General Tracker ID GEO PC Synchro Manual Real Time Clock 09 07 2009 15 57 28 Motion Sensor Sensitivity Stop Timeout Silent Mode GPRS Connection GETA User Name AP IP Password Host IP Name Port Rate 10min Power Save Mode Position SMS Motion Sensor 28 Setup by MyTrack Software Alarm SMS To enable disable the Alarm SMS and set the phone number connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup 3 Recordings Alam SMS Desinaton Phone Nu eo een 4383401234567 Memory Full Position SM v Enable Destination Phone Nr 393401 234567 Geofence amp Anchor Geofence Latitude Longitude 1st 43 210420N 3 867188E Destination Phone Nr 4383401234567 2nd 45 583280N _ 15 896093E Map View v Anchor Destination Phone Nr Radius 393401234567 100m jw SMS Language SMS Language
23. r s Limited Warranty Warranty Period Safety Instructions Safety Instructions Please read the following safety instructions carefully Not following them may be dangerous and or illegal For further details please read carefully the user manual complete version contained in the enclosed CD ROM Do not switch the device on when prohibited or whenever it could cause any interference or danger Obey all local laws Always keep your hands free to operate the vehicle while driving Your first consideration while driving should be road safety All wireless devices may be susceptible to interference which could affect the performance of other appliances TV radio Switch the device off in hospitals or near medical equipment hearing aid equipment pacemaker the device could cause interference Always keep a distance of 20 cm between pacemaker and device Wireless and digital devices can cause interference with aircraft equipment Donotusethe device at a refuelling point Switch off when near petrol stations or fuel depots and chemical plants The device could interfere with the correct functioning of the electronic equipment Do not use the device where blasting is in progress Do not use the device for any uses other than those it has been built for Keep to the instructions as explained in the product manual Only qualified personnel may install or repair this product Useonly approved accesso
24. ries and batteries Do not use incompatible products The use of nonstandard products can cause damage to device and or people The batteries must be disposed according to the appropriate modes The consumer must duly hand in worn out batteries either at the appropriate collection points for the general public in his own town or wherever batteries of the same kind are sold compulsory warning according to law on the disposal of batteries The device is not water resistant keep it dry Contact with water or any other liquid could cause serious damage to the device General Information General Information The tracker is a portable device able to transmit its geographical location to a mobile phone or PC in real time and to send SOS messages in case of an emergency Moreover the detected data can be recorded for further analysis The tracker is available in two different versions LCD GPS tracker with display phone and 2MB data storage memory BOX GPS tracker without display without vocal communication and with 512kB data storage memory Both trackers can be offered combined in the KIT version particularly indicated for the use of Finder function useful for real time locating This User Guide describes the tracker in the BOX version The tracker has two basic version locating and transmitting its actual position sending an SOS message in case of an emergency The tracker is provided with MyTrack software al
25. seful if combined with the Scout web server as it allows to display the detected positions by every station connected to internet To use this function it is necessary to set the GPRS communication parameters using the provided software or sending an SMS command enable the function setting the rate for cyclic GPRS connection using the provided software Anchor The Anchor function allows to monitor within a pre established circular area the position of a person an object or an animal When the tracker detects the exiting from the pre established area or the ri entering it sends an alarm SMS containing its position data to the preset phone number This function is programmable using the complete SMS command enabling and radius setting or partially by the provided software When the complete SMS command is received by the tracker e g wanc 1 0500 the function is enabled and the current tracker position is considered as area central point If the function is enabled without setting the radius the previously set coordinates for the central point and the last programmed radius will be considered If no radius was previously programmed by default it will be set to 100 m This function is programmable completely by SMS command wanc By the provided software only function enabling and radius setting is possible A Before enabling this function it is necessary to set the phone number where SMS will be sent by means of the provided so
Download Pdf Manuals
Related Search