KFV60 - KFV90
Contents
1. 530 Components Ref Product Components 1 1 Hood Body complete with Controls Light Blower Filters 2 1 Telescopic Chimney comprising 2 1 1 Upper Section 2 2 1 Lower Section 8a 1 RightAir Outlet Grill 8b 1 LeftAir Outlet Grill 9 1 Reducer Flange 150 120 mm 14 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells 141 2 Air Outlet Connection Extension 15 1 Air Outlet Connection Ref Installation Components 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 6 6 Screws 4 2 x 44 4 Screws 2 9 x 9 5 Q ty Documentation 1 Instruction Manual INSTALLATION Wall drilling and bracket fixing Wall marking Draw a vertical line on the supporting wall up to the ceiling or as high as practical at the centre of the area in which the hood will be installed Draw a horizontal line at 650 mm above the hob Place bracket 7 2 1 on the wall as shown about 1 2 mm from the ceiling or upper limit aligning the centre notch with the vertical reference line Mark the wall at the centres of the holes in the bracket Place bracket 7 2 1 on the wall as shown at X mm below the first bracket X height of the upper chimney section supplied aligning the centre notch with the vertical line Mark the wall at the centres of the holes in the bracket Mark a reference point as indicated at 116 mm from the vertical reference line and 302. ese Omeg Libretto di Istruzioni Instructions Manual Manuel d Instructions Bedienungsanleitung Gebruiksaanwijzing Manual de instrucciones Manual de Instru es Bruksanvisning KFV60 90 INDICE CONSIGLIE SUGGERIMENTI CARATTERISTICHE RECOMMENDATIONS AND SUGGESTIONS CHARACTERISTICS AEAN AARNA 13 SOMMAIRE CONSEILS ET SUGGESTIONS 18 CARACTERISTIQUES INHALTSVERZEICHNIS EMPFEHLUNGEN UND HINWEISE 25 5 BEDIENUNG WARTUNG INHOUDSOPGAVE ADVIEZEN EN SUGGES TIES 32 INSTALLATIE ONDER HOU Distt INDICE CONSEJOS Y SUGERENCIAS
3. sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concern ing use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appli ance MAINTENANCE lt Switch off or unplug the appliance from the mains supply before carrying out any maintenance work Clean and or replace the Filters after the specified time period Fire hazard Clean the hood using a damp cloth and a neutral liquid detergent The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product CHARACTERISTICS Dimensions 135 NY 2 tas 8 f 598 698 898 300 150 Min Min 650mm 650mm 260 i 520
4. the metal grease filters e Remove the saturated activated carbon filter by re leasing the fixing hooks Fit the new filter by hooking it into its seating Refit the metal grease filters Lighting LIGHT REPLACEMENT 20 W halogen light e Remove the snap on lamp cover levering it from under the metal ring supporting it with one hand e Remove the halogen lamp from the lamp holder by pulling gently e Replace the lamp with a new one of the same type making sure that you insert the two pins properly into the housings on the lamp holder Replace the snap on lamp cover
5. 39 CARACTERISTICAS NDICE CONSELHOS SUGESTOES A E O ON 46 47 INSTALA O UTILIZA O sss 51 MANUTENCAO au aan anda ad 52 53 i VX REAS Ahk OES MeN ANE I AT ie A Pe INNEHALL REKOMMENDATIONERO CH TIPS 60 EGENSKAPER iaruinn INSTALLATION ANVANDING RECOMMENDATIONS AND SUGGESTIONS Instructions for Use apply to several versions of this appliance Accord ingly you may find descriptions of individual features that do not apply to your specific appliance INSTALLATION The manufacturer will not be held liable for any damages resulting from in correct or improper installation The minimum safety distance between the cooker top and the extractor hood is 650 mm some models can be installed at a lower height please re fer to the paragraphs on workin
6. 6 mm above the horizontal reference line Repeat this operation on the other side Drill 8 mm holes at all the centre points marked Insert the wall plugs 11 in the holes Fix the brackets using the 12a 4 2 x 44 4 screws supplied Insert the two screws 12a 4 2 x 44 4 supplied in the hood body fixing holes leaving a gap of 5 6 mm between the wall and the head of the screw Mounting the hood body e Before attaching the hood body tighten the two screws Vr lo cated on the hood body mounting points Hook the hood body onto the screws 12a Fully tighten the support screws 12a e Adjust the screws Vr to level the hood body Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm the choice of which is left to the installer To install a 120 mm air exhaust connection insert the re ducer flange 9 on the hood body outlet e Fix the pipe in position using sufficient pipe clamps not sup plied e Remove possible charcoal filters RECIRCULATION VERSION AIR OUTLET e Assemble the two halves of the hood body extension piece 14 e Push fit the assembled hood body extension piece 14 onto the air outlet e Push fit connection 15 onto the hood body extension piece 14 e Insert the connection extension pieces laterally 14 1 connec tion 15 e Make sure that the outlet of the exten
7. al symbols are to wards the top and front of the hood Also make sure that they are correctly inserted in the connection extension pieces 14 1 USE L KOOD S Vi 3 Light Switches the lighting system on and off S Led Motor running led 1 Motor Switches the extractor motor on and off at low speed Used to provide a contin uos and silent air change in the presence of light cooking vapours V2 Speed Medium speed suitable for most operating conditions given the optimum treated air flox noise level ratio V3 Intensive Maximum speed used for eliminating the highest cooking vapour emission including long periods MAINTENANCE Grease filters CLEANING METAL SELF SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of opera tion or more frequently for particularly heavy usage and can be washed in a dishwasher Remove the filters one at a time by pushing them to wards the back of the group and pulling down at the same time e Wash the filters taking not to bend them Allow them to dry before refitting When refitting the filters make sure that the handle is visible on the outside Activated charcoal filter Recirculation version REPLACING THE ACTIVATED CHARCOAL FILTER The filter is not washable and cannot be regenerated and must be replaced approximately every 4 months of operation or more frequently for particularly heavy usage e Remove
8. g dimensions and installation Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood For Class appliances check that the domestic power supply guarantees adequate earthing Connect the extractor to the exhaust flue through a pipe of minimum diame ter 120 mm The route of the flue must be as short as possible Do not connect the extractor hood to exhaust ducts carrying combustion fumes boilers fireplaces etc If the extractor is used in conjunction with non electrical appliances e g gas burning appliances a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air USE The extractor hood has been designed exclusively for domestic use to elimi nate kitchen smells a Never use the hood for purposes other than for which it has been designed lt 650 mm min Never leave high naked flames under the hood when itis in operation Adjust the flame intensity to direct it onto the bottom of the pan only making sure that it does not engulf the sides Deep fat fryers must be continuously monitored during use overheated oil can burst into flames Do not flamb under the range hood risk of fire This appliance is not intended for use by persons including children with reduced physical
9. sion pieces 14 1 is hori zontally and vertically aligned with the chimney outlets If this is not the case adjust the position by either reversing the con nection extension pieces 14 1 or by cutting the hood body ex tension 14 along one of the thinner section channels denoting the pre fixed lengths then reassemble as described previously The air outlet directional grills 8 8b must be fitted after the lower outlet duct has been installed e Ensure that the activated charcoal filters have been inserted ELECTRICAL CONNECTION Connect the hood to the mains through a two pole switch ing a contact gap of at least 3 mm Remove the grease filters see paragraph Maintenance being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan Flue assembly Upper exhaust flue e Slightly widen the two sides of the upper flue and hook them behind the brackets 7 2 1 making sure that they are well seated Secure the sides to the brackets using the 4 screws 12 2 9 x 9 5 supplied Lower exhaust flue e Slightly widen the two sides of the flue and hook them be tween the upper flue and the wall making sure that they are well seated Fix the lower part laterally to the hood body using the 2 screws 12 2 9 x 9 5 supplied On the recirculation version fit the directional grids 8a 8b in their housings making sure that the direction
Download Pdf Manuals
Related Search