ELX8-60 Users Guide
Contents
1. FCC Compliance Statement Caution Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type Dispose of used batteries according to the genera2. Channel Status When On all eight analog channels will record based on the Quick Setup settings Rugged CCTV 2003 08 13 v 1 0 25 ELXS 60 Basic Configuration Recording Speed Quality There are four conditions Low Standard High Custom conditions except Custom will synchronize Speed ips and Quality automatically Low setting is lips Q5 Standard setting is 5ips Q5 High setting is 15ips Q5 When using the Custom setting Speed ips and Quality can be set separately Audio Recording Enables the audio recording feature If audio is set as On and Audio Synch with is set in the Audio menu under the System tab audio will be available in Playback Mode with all channels Apply Confirms the Quick Setup Recording settings ELX8 60 will begin recording after pressing the Apply button and exiting from the recording menu 26 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 2 Camera This menu is for configuring individual cameras In Quick Setup camera status is automatically set as On Settings such as Brightness and Contrast can be set for each channel The values assigned will apply for both monitoring and playback modes Quick Setup Camera Normal Rec Alarm Relay Cama Status On Cam amp 3 4 NTSC 5 Color Color Gain Control
3. 8 R E 9 293 Instalaton 10 11 cuj 11 3 1 Viewing basic screen quad split esee eee nennen nennen nnn nnn nnns 11 3 2 Viewing single full 11 3 3 Viewing MUN lt 11 3 4 Viewing all channels with sequence mode 12 3 5 Viewing an alarm triggered channel 13 3 6 Viewing images with Digital ZOOM 13 3 7 Viewing with connected P LZ bosse aae etos 13 221 108 t 15 dud cud 15 PAT 16 4 1 Playback various 16 4 1 1 Playback via basic screen full screen esses 16 4 1 2 Playback via 16 4 1 3 Playback ch5 to ch8 via quad split screen sss 16 4 1 4 Playback with Digital ZOOM editt 16 4 1 5 Various playback modes eese 16 LRL MEE
4. 8 live monitoring channels 1 4 9Ch Mode on CCTV Monitor as well as PC Maximum 4TB storage capacity IEEE 1394 for external HDD Various configuration with recording and playback conditions Intelligent file system for managing event triggered video data ATM POS transaction information text recording and search with corresponding video 4 pairs of sensor inputs and alarm outputs Built in hardware motion detection with search function 64 division comparison Back up with IEEE 1394 FiWi PTZ Control Preset support via RS 232 and RS 485 RS422 User friendly 32bit True colored Graphic OSD Menu Dynamic IP DHCP Floating IP support when xDSL and Cable Modem are used Wavel amp compression 1 5KB Average file size with standard image quality Embedded Linux OS for excellent stability and reliability IR remote controller User controls PTZ with remote controller DVR Manager User Interface of PC 15 to be listed with 32 units of ELX8 60 on a program 256chnnels 32sets of ELX8 60 x 8 channels are controllable through a program Rugged CCTV 2003 08 13 v 1 0 7 ELXS 60 OVERVIEW 2 Product Description 2 1 Front Panel 1 Remote Controller 2 Channel 4 Function selection 5 Direction Replay Receiver Selection Button button Button 1 Remote Controller Receiver 2 Channel Selection Button To select video input channelin monitoring and playback mode 3 LED PWR Displays power status When lit power is su
5. Arrow key Replay function or to move inside the Configuration menu 2 2 Rear Panel 6 Power 2 Audio 1 Serial Port amp DIO 3 Video 4 Video port Output Input 1 Serial Port amp DIO Serial RS232 9Pin D Sub Connector amp RS232 422 485 terminal block Sensor In 4 sensor inputs Relay Out 4 Alarm Relay outputs 2 Audio port 1 audio input amp 1 output 3 Video Output monitor output amp 1 VCR output 4 Video Input 8 video inputs 5 Ethernet 6 Power Rugged CCTV 2003 08 13 v 1 0 9 ELXS 60 OVERVIEW 2 3 Installation Summary Connect Camera Connect Monitor Connect Ethernet This is optional to view image on remote location Connect Audio Connect Power amp Run 10 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 Basic Configuration 3 Monitoring Once power is supplied to ELX8 60 default quad split monitoring mode analog channels 1 4 will be displayed Th e following steps apply for ELX8 60 s monitoring menus lt Button control gt Press the MULTI button on the front panel of ELX8 60 to change the split configuration 4 9 For sequence mode press the SEQ button on the front panel of ELXS 60 To configure the sequential cycle access the Monitor tab of Configuration Menu 3 1 Viewing basic screen quad split Insert AC c
6. Brightness 1 9 8 Contrast lt lt lt 9 3 None Address 0 Channel 1 Analog Video Source configuration menu Press Enter to configure lt Button control gt Press MENU button and use the ARROW keys to move to each channel below the Camera tab Name Assign a customized name to the channel Press ENTER to open the necessary dialogue box Rugged CCTV 2003 08 13 v 1 0 27 ELXS 60 Basic Configuration lt TIP gt When assigning a name to a channel the following dialogue box will appear This box is also used later in the system but the method is always the same 1 2 34 5 6 7 8 9 O0 To select a letter use the ARROW and buttons or the number buttons ELX8 60 front panel 0 to 9 When using the ARROW buttons use the PLAY button to select each choice The intersection between the horizontal and the vertical bar is the selected choice Pressthe button to confirm the selected value Or enter the related numbers in order of horizontal vertical For example in order to select press 3 and 2 button After setting all values press the Exit button Function Key v Enter lt Back Space amp delete EE Space Left Right 4 Previous Code Page 4 Next Code Page 28 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 Status Set On Off using the or buttons after pressing the ENTER butt
7. If enabled all images Normal and Alarm will be written over based a first in first out basis Backup Reminder A Backup Reminder can be set to remind users to backup the HDD The reminder can be set to appear daily weekly or monthly Day Date Time To set the time for the Backup Reminder Rugged CCTV 2003 08 13 v 1 0 43 ELXS 60 Basic Configuration 5 7 7 Network There are four sub menus Network xDSL HRS and Port Setting 5 7 7 1 Network This page is to define network type and set network addresses forELX8 60 Es Alarm Rec Relay Monitor Utility Audio Time Schedule DHCP Off Special Time IP Addr 192 168 0 92 Security Net Mask 255 255 255 0 Disk Setup Gateway 192 168 0 1 Serial Setup DNS 0 0 0 0 Miscellaneous DNS3 0 0 0 0 Configure network settings Type This is to select proper network interface Ethernet xDSL with which ELX8 60 is connected If ELX8 60 is connected with Internet dedicated line cable modem line or on LAN environment select network interface as Ethernet If ELX8 60 is connected on xDSL line that needs PPPoE process to connect to the Internet administrator should select xDSL However if the xDSL line does not need PPPoE process administrator should select Ethernet even though ELX8 60 is connected on xDSL line DHCP Basically this menu is for the lines that have Ethernet interfaces such as Internet dedicated line cable mod
8. Wavelet Algorithm the ELX8 60 processes analog video into crisp clear and court admissible pictures that are up to 500 smaller than comparable JPEG images With this efficiency ELX8 60 records over 30 days on a 200GB hard disk drive when recording 4 channels at the speed of IOips per channel ELX8 60 also allows users to record and playback audio for one channel Setting up ELX8 60 is as easy as setting up a VCR ELX8 60 starts to record as soon as power is supplied and CCTV cameras are connected ELX8 60 offers an easy setup as well as advanced menus With Quick Setup ELX8 60 can be setup and begin recording in as little as 5 minutes The default settings offer quality and efficiency without the hassle of confusing menus Equipped with 2 IEEE 1394 ports Fire Wire and 3 USB ports ELX8 60 can expand its recording capacity to up to 4TB easily For easy backup Windows FAT32 formatted HDD is compatible with ELX8 60 Simply back up the desired data and connect the HDD to your PC to review critical images 6 2003 08 13 v 1 0 Rugged CCTV OVERVIEW ELXS 60 Key features 6 analog video channels channel audio recording amp playback Recording Playback Back up images and Networking at the same time Quadplex Total 60 ips recording speed Total 240 ips display speed Displaying live and recorded images on PC as well as CCTV Monitor Builk in hardware Quad Splitter for analog video Built in software multiplexer for all
9. system Recording Set to On using the ENTER button and the ARROW buttons to record audio Audio Gain Increases or decreases the sensitivity to the audio signal Can be set between 7 and 8 20dB To amplify the audio input signal Should ONLY be used when using an external microphone Sync Audio with Designate which channel s to synchronize audio with during playback Rugged CCTV 2003 08 13 v 1 0 37 ELXS 60 Basic Configuration 5 7 2 Text ELX8 60 can display and playback text data of Access Control POS ATM with relevant video system Recording Monitoring In order to make ELX8 60 input text data both of menus should be set as Sync Text With To set channel to synchronize with text Device Currently the protocol of Star Finger 007 Access control model is built in ELX8 60 as text device Rugged CCTV will keep updating such protocols When connecting another text device set as Manual Then manual mode setting menu will be displayed Set each value with referring the manual of connected device 38 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELX8 60 n 4 Alarm Rec Relay Monitor Utility 09 Audio Recording Time Schedule Sync Text With All Special Time Device Manual Security Seek Header Dick Setup Header 1 Header Network Header 2 Header Serial Setup Delimiter DOA Miscellaneous Timeout ms 2000 L
10. to left and right and 4 step up and down To move the zoom box use the Arrow button To cancel the zoom box press the ZOOM button once more 3 Viewing with connected PTZ Pan Tilt Zoom PTZ devices can be controlled through the ELX8 60 when a PTZ device is connected and properly configured under Serial Setup Zoom Focus While in Monitor mode press the SELECT button Channel selection icon will be displayed Load Preset Move the icon to the chamel to control with the Arrow button Save Preset Press the MENU button PTZ menu Pan Tilt Zoom Focus Load Preset Save Preset will appear Press the ENTER button after selecting the desired function Rugged CCTV 2003 08 13 v 1 0 13 ELXS 60 Basic Configuration VIDEO RECORDER 08 Pan Tilt Control To control Pan and Tilt during live image monitoring mode Press the SELECT button Move the Select icon to the desired channel Press the MENU button Select Pan Tilt from the PTZ Menu Control pan and tilt function using the up down left and right arrows Zoom Focus Control To control Zoom and Focus during live image monitoring mode Press the SELECT button Move the Select icon to the desired channel Press the MENU button Select Zoom Focus from the PTZ Menu Control zoom and focus functions using the up down left and right arrows of front panel L
11. 1 for Monitoring and port 8105 for Playback To change port number to an open port some firewalls and or ISPs block certain ports press the ENTER button and use the dialogue box TP Server Port The port used for Transparent Protocol server Firewall Port If there is a firewall on the network and a unique port is available user may configure the Monitor and Playback ports as one port In order to change a port select Port menu and configure a suitable port value Rugged CCTV 2003 08 13 v 1 0 49 ELXS 60 Basic Configuration 5 7 7 5 NTP Setting NTP Network Time Protocol makes time of Network devices synchronize They are composed of a central server for supplying standard time via Network and a client for receiving the synchronized time with connecting the server Alarm Rec Relay Monitor System Utility HTP Setting Audio Text a NTP Mode Client Time Schedule NTP Server Loc Public Special Time NTP Local Server IP 0 0 0 0 Security Interval min 0 Disk Setup Serial Setup Miscellaneous Configure DVR settings NTP Mode Set ELX8 60 s NTP mode between Client and Server NTP Server Loc It is possible to set when NTP Mode 15 set as Client Set whether NTP server is on Local Network Internet Public NTP Local Server IP It is possible to set when NTP Server Loc Is set as Local Set the server s IP address Set NTP server s IP a
12. 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 7 4 Special Time Time Up to four zones can be designated as Special Time Rugged CCTV 2003 08 13 v 1 0 41 ELXS 60 Basic Configuration 5 7 5 Security Security User Password Designate a User s Password for access to monitoring and playback Default password is 0000 Admin Password Designate an Administrator s Password to control access to Configuration Menu and full system control authority Default password is 9999 Remote Setup When set to Enable users can configure ELX8 60 through the S W interface from aremote site via network Remote Relay Enables access to the Relay menu from remote site 42 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 7 6 Disk Setup Alarm Relay Monitor Utility Audio Auto Del Normal On Auto Del Alarm On Time Schedule Backup Reminder Weekly Special Time Day Date Mon Security Time 13 00 Serial Setup Miscellaneous Configure options for disk management Press Enter to configure b Auto Del Normal Images and data recorded under the Normal condition are automatically deleted as the hard drive s reaches capacity Images are written over based on a first in first out basis Images recorded based on Alarm conditions are not written over Auto Del Alarm
13. Backup Data Backup Manager Start Date 2003 04 01 Time 10 12 End Date 2003 04 01 Time 41 12 Select Disk 1 Disk s Size KB Start Start Date amp Time End Date amp Time To designate backup range Select Disk To select which storage will be used as backup device To change the disk status use the Disk Manager menu under the System tab Note Backup Manager does not support USB devices Backup Manager will ONLY work with devices connected through IEEE 1394 FireWire ports 20 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 4 3 3 Delete Data To delete a specific file range from the current recording HDD This menu does not affect backup disk The beginning of the range is always the beginning of the recording on the HDD Rugged CCTV 2003 08 13 v 1 0 21 ELXS 60 Basic Configuration 5 Configuration 5 1 Quick Setup There are three menus for recording setup Quick Setup Normal Recording Alarm Recording menu in Configuration Menu Quick Setup is the easiest setup activating all eight analog cameras to record with the same settings and conditions Normal recording is the standard recording settings and can be customized based on time and channel Alarm recording is the recording schedule based on alarm conditions Motion Detection Sensors etc Also Quick Setup has time setting menu 5 1 1 Date Time When 8 60 is manufactured in factory ti
14. MENU 57 6 1 2 Setting at Serial Setup s RS232 MENU 58 6 1 3 Setting at Alarm Rec 58 6 1 4 Setting at Normal Rec 59 6 2 Using ea es 60 6 2 4 Setting at Serial Setup s 232 60 6 2 2 Setting at Serial Setups PTZ menu essen nennen tenentes 60 APPENDD 61 1 Technical Specification 62 2 Utilizing IP Addresses on Local Network eese nennen tnter nnns 65 00102101 METTE 65 2 2 P construction and Network CLASS 65 2 3 C class NetWork 66 Rugged CCTV 2003 08 13 1 0 5 ELXS 60 OVERVIEW OVERVIEW 1 Introduction ELX8 60 supports 8 analog video channels Video Audio and Text Event Logs are digitized and stored on two internal hard drives Using a Proprietary Wavelet Algorithm average file size is 1 5 while still maintaining clarity high enough for facial recognition In addition Wavelet compressed images are impossible to manipulate Due to our proprietary
15. R eR niece 18 4 3 Copy Backup Delete Data Manager sess 19 4 3 1 00 BM 19 4 32 Backup 20 233 21 5 OI mm 22 000 22 S NET 1 X 22 212 25 4 2003 08 13 v 1 0 Rugged CCTV TABLE OF CONTENTS ELXS 60 SEES II ee 27 2 6 08 62 2 2 30 Fey 33 2M o mcs U 35 O M 36 v i e E E 37 cc E 37 T o4 eee ee eee eee ee ee Ne ee ene eee eee eee 38 5 73 Time 5 080 8 5 ee eee ee 40 Se 41 v0 42 5 7 6 5 SetUp vcccsccsssesscssssssccsssscsessssecscsssnescessssescesssteecesnusecesssueecessnseceesnetecessnueecessueserssnueeessnieeessnenees 43 21212 44 YO 51 15001208 015 ee et are 52 59 ee ee ere ee ee eon ee ee ee eee 54 581 Disk Manage 55 57 Connecting External Device re i ehem dence 57 6 1 2 01160 8018 25555 ee 57 6 1 1 Setting at Text
16. and the numbers are from to 255 Among the numbers 0 is used for Network ID 1 15 used for Router IP Gateway address and 255 is used for Broadcast address Therefore the numbers from 2 to 244 are IP addresses that can be assigned to products Network ID It is to identify a network Generally the first number is assigned as Network ID Gateway address It is an IP address of router that is connecting Internet and local network Remote users can access local network over Internet through the gateway router Generally the second number is assigned as Gateway address Broadcast address It is to broadcast to all devices that are connected on local network Broadcast address is a destination for broadcasting and it is determined by calculating All devices connected on local network have a same Broadcast address Subnet Mask It is to divide a local network into two remote networks Subnet mask shows the IP quantity in a certain network The numbers that can be used as subnet mask are limited 0 4 8 16 32 64 128 2 Network configuration 1 To use as one network Network ID Gateway Address Subnet Mask 255 255 255 0 Broadcast Address xxx xxx xxx 255 IP Addresses xxx xxx xxx 2 xxx xxx xxx 254 66 2003 08 13 v 1 0 Rugged CCTV APPENDIX ELXS 60 2 To use as two sub networks 1 2 1 2 Sub Network ID xxx xxx xxx 0 Gateway Address S
17. ay night Four segment time frame Weekly Weekdays Weekends Conditions MD sensor input Recording speed None to 30 fps Image quality 5 Levels Event conditions MD amp sensor inputs Pre Alarm Recording 1 10 seconds Post Alarm Recording 60 seconds 2003 08 13 v 1 0 Rugged CCTV APPENDIX Intelligent file system Event Triggered Video Data Preservation Event Log Recording Data Video amp Audio Clip Back up Data Copy I minute s video clip Displaying Performance Digital Zoom Event Triggered Pop up Video PTZ Control Local User Remote User Sensor Inputs and Alarm Outputs Rugged CCTV ELXS 60 Data loss protection against power failure Overwrite prevention of Event triggered data Log archiving on HDD Log search amp monitoring via Network External HDD IEEE1394 FireWire USB PnP Memory Stick USB port VHS Video Tape Video output port for VCR Backup Notification Daily Weekly Monthly PnP USB storage Compact Flash Smart Media Memory Stick SD Card Frame Rate on CCTV Monitor Max 120fps Frame Rate on PC Max 60ips Display Channel Quad Auto Sequential Misc Play speed 1 2x 4x 8x 16x FDW amp REV Supports Step Forward Step Reverse Instant data access based on time and event log 2 times digital zoom Live amp Playback Mode Triggered by motion detection or sensor input Ports RS232 RS485 RS422 Front panel push but
18. ay output schedule Press Enter to configure Setup Alarm triggered events MD or Sensors can be set to trigger Relays 1 through 4 When set the event will trigger the corresponding digital output Special Time Enable Special Time to apply the relay schedule to the Special Time Zone Rugged CCTV 2003 08 13 v 1 0 35 ELXS 60 Basic Configuration 5 6 Monitor This menu is to set display image on monitor Alarm Rec Relay j Monitor System Utility Cofiguration Seq Switching sec I Alarm Pop up On Pop up Configure display preferences for real time channel switching Press Enter to configure Seq Switching sec set sequence time between and 60 seconds Alarm Pop up Pop up Hold sec To set alarm pop up screen Pop up duration time can be set between 5 and 10 seconds If setting as Keep pop up screen keeps holding In order to cancel Keep mode press another channel button lt Note gt If channel 1 pops up and channel 2 also pops up during pop up hold time screen is changed to quad split screen and channel and 2 are shown And the pop up hold time is extended automatically Up to eight channels 36 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 7 System 5 7 1 Audio ELX8 60 supports one channel audio input This single audio channel can be replayed with any connected channel or with all of them
19. c Configuration lt Setting MD Area gt Designate a specific area for motion detection triggered event Press the Custom Area button to customize the motion detection area The area is divided into 64 blocks 8 X 8 Selected MD area is indicated in dark gray To remove blocks from motion detection select the block using the ARROW buttons and press the ENTER button Press the EXIT button when finished Text In order to display or record text with image it should be set as For more detail setting methods please refer to Using Text Data Recording Speed Quality There are four conditions Low Standard High Custom All conditions except Custom synchronize Speed ips and Quality automatically Low setting is lips Q5 Standard setting is 5ips Q5 High setting is 151 5 05 When using the Custom setting Speed ips and Quality can be set separately Pre Alarm sec Set a value upto 10 seconds to record video Pre Alarm Post Alarm sec Set a value up to 60 seconds to maintain recording conditions Post Alarm 34 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 5 Relay This menu is to set the relay commands according to each time schedule Quick Setup Camera Normal Rec Alarm Rec Woekday Day gt gt 1 MG MOE 51 53 54 Configure rel
20. configure Weekday Start End Press ENTER to access the Time Setting Set the range for Weekday between Monday and Sunday using the or buttons Weekend is set automatically based on Weekday range Day Start End Set the range for Day using the up down buttons The Night range is set automatically based on Day range Recording Speed Quality There are four conditions Low Standard High Custom All conditions except Custom synchronize Speed ips and Quality automatically Low setting is lips Q5 Standard setting is 5ips Q5 High setting is 15ips Q5 When using the Custom setting Speed ips and Quality can be set separately Special Time Recording This menu is to designate different recording conditions during Special Times Special Time is designated under the System tab There are four conditions Low Standard High Same as above Rugged CCTV 2003 08 13 v 1 0 31 280 lt Setting Special Time gt To set Special Time move to System tab Alarm Rec Relay Monitor eC Utility Audio Zonei 00 00 to 00 00 Text Zonez 00 00 to 00 00 Time Schedule 00 00 00 00 Special Time Zoned 00 00 to 00 00 Security Disk Setup Serial Setup Mizcaelinmnenmus Special tints excepltioss to normal recarding amd relay output Presa Enter te configure Up to four zones ca
21. ddress on local Network or the IP address of ELX8 60 that is set as server in NTP mode Interval min Set a synchronizing interval 50 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELX8 60 5 7 8 Serial Setup There are two RS232 menus One for external devices connected via the DB 9 pin and the other for PTZ setting and one RS 422 485 menu 5232 Serial Setup Device Designate the connected external device Interface Used to designate the protocol on the RS422 RS485 Menu Baud rate Parity Stop bit Data bit Each value should be set according to the specifications of the connected external device Rugged CCTV 2003 08 13 v 1 0 51 ELXS 60 Basic Configuration 5 7 9 Miscellaneous TT 4 GN Rec Relay Monitor Utility 2 Audio Remote Control ID Text Keyboard Control Addr 32 Time Schedule Keyboard PTZ Addr 1 Special Time DVR ID DVR Security Alarm Buzzer Off Disk Setup Languages English Network Serial Setup Reset Values Miscellaneous Press Enter to configure RE Button control Press MENU button and select Miscellaneous below the System tab Remote Control ID Up to sixteen ELX8 60s can be controlled with a single IR Remote Control Designate each unit with a unique number under the Remote Control ID menu lt How to set remote controller gt Aim remote controller at the ELX8 60 Press
22. e L Set text event as On 58 2003 08 13 v 1 0 Rugged CCTV Advanced Configuration ELXS 60 6 1 4 Setting at Normal Rec menu Quick Setup Camera Normal Rec Alarm Rec Relay 4 Weekday Day a Recording Speed Quality High Camia Speed ips 45 4 Quality G5 Best Special Time Recording Same as above Event Recording On Configure normal recording schedule for for channel 1 Analog Video Press Enter to configure Set event recording as at each time schedule Note Whenever pressing the Help button information of displayed image is different The default value of Monitoring mode is to show just channel number Then next step is to show channel name and text event status and HDD status The default value of Playback mode is to show all information The next level is to show channel name and text event status and channel number So in order to view text data press the Help button once at both Monitoring and Playback modes Rugged CCTV 2003 08 13 v 1 0 59 ELXS 60 Advanced Configuration 6 2 Using Keyboard In order to use keyboard the following two menus should be set Serial Setup s RS232 menu Serial Setup s PTZ menu 6 2 1 Setting at Serial Setup s 5232 menu HEN oC 0 Interiace Hone Stop 1 Dats Configure settings for remote devices tha
23. em line and LAN If administrator activates DHCP menu all addresses are set automatically by ELX8 60 detecting them from DHCP server of your ISP The detected addresses are not displayed on the screen The addresses do not need to be entered manually unless DHCP is disabled 44 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 DHCP can also be used for xDSL PPPoE interface Sometimes all computers a Local Area Network LAN share a single Floating Dynamic IP address In this case the ELX8 60 should be assigned a private IP address and have DHCP enabled Users on the LAN can connect to the ELX8 60 using the private IP address and outside users can connect to the ELX8 60 over the Internet IP Address NetMask and Gateway Address DNS Administrator may configure IP address subnet mask gateway address and DNS addresses of ELX8 60 DNS Server IP Address The DNS server address is the address of the RUGGED CCTV Registration Server HRS If using dynamic registration the DNS Server IP address should be the address of the HRS 210 110 114 37 Rugged CCTV 2003 08 13 v 1 0 45 ELXS 60 Basic Configuration 5 7 7 2 XDSL If ELX8 60 is connected on xDSL line and needs PPPoE process the network administrator should configure the user ID and password for PPPoE ID The password may be acquired from the ISP that installed the line Once configured the ELX8 60 will receive an IP address when it
24. ess the ZOOM button during the basic single channel playback mode Digital Zoom will expand the image to twice its normal size Default location of the digital zoom is in the center of screen The zoom box can be moved each 10 step to left and right and step up and down To move the zoom box use the Arrow button To cancel the zoom box press the ZOOM button once more 4 1 5 Various playback modes PLAY To begin playback mode and replay at 1x speed After pressing PAUSE PLAY will advance recorded images frame by frame 16 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 STOP To stop replaying PAUSE To pause replaying FAST FORWARD Each press of the button will increase playback speed gradually x1 x2 x4 x8 x16 FAST REWIND Each press of the button will increase playback speed gradually x1 x2 x4 x8 x16 STEP FORWARD Pressing PLAY or FAST FORWARD button from PAUSE status will replay image frame by frame In order to go back to normal playback mode press STOP button then press PLAY FAST FORWARD button STEP REWIND Pressing FAST REWIND button from PAUSE status will replay image frame by frame In order to go back to normal playback mode press STOP button then press PLAY FAST FORWARD button Rugged CCTV 2003 08 13 v 1 0 17 ELXS 60 Basic Configuration 4 2 Using Search M
25. figuration 5 8 Utility The following description is how to add format internal or external HDD ELX8 60 supports various external storages 4 Relay Monitor System Utility Disk Manager TR drive management Button control Press MENU button and move to Utility belowthe System tab 54 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 8 1 Disk Manager A connected HDD is detected automatically Disk Manager Select Disk 2 Disk s V IntA Maxtor 4 08010 80043264 Action None Alarm Partition 10 Select Disk To select a Disk Action Select from Add Remove Format Confirm Removed Add used Format Format ELX8 60 s file system Not available to PC file system Add Add HDD for recording Need to format Add Used Add a HDD that has been used and formatted There is no need to reformat It is possble only when HDD 15 added as Primary Disk Remove Remove current HDD HDD can be reused without data loss by the Add Used command Confirm Removed Used when a removed HDD is still listed ALL DATA WILL BE LOST Rugged CCTV 2003 08 13 v 1 0 55 ELXS 60 Basic Configuration Type There are several symbols to indicate HDD status Available for recording V Connected and formatted as ELX8 60 s file system If using Add used command it will be changed to There
26. ines 20 Text configuration Seek Header If a protocol is built in ELX8 60 like Star Finger 007 this setting is needless Otherwise ELX8 60 can t recognize which parameter value is input to ELX8 60 Namely all information has starting point and ending point Header means starting point that is always inserted So when this header data is transmitted to ELX8 60 ELX8 60 can recognize it as starting point Two headers can be set maximally Delimiter Because delimiter value may be different refer to the manual of related device Timeout ms The following Lines means maximal text line that can be included within a data However length of each data may be different Because ELX8 60 can t recognize it automatically timeout menu is needed Namely if specific time passes after ELX8 60 receives the last line ELX8 60 will regard it as normal data and decide to record Lines To set maximal line of a data Rugged CCTV 2003 08 13 v 1 0 39 ELXS 60 Basic Configuration 5 7 3 Time Schedule To designate Weekday Weekend and Day Night Time Schedule Weekday Start End Press ENTER to access the Time Setting Set the range for Weekday between Monday and Sunday using the or buttons Weekend is set automatically based on Weekday range Day Start End Set the range for Day using the up down buttons The Night range is set automatically based Day range 40 2003 08
27. ing time backward old images will be lost 1 lt Note gt Most setting values are applied automatically when exiting from the related menu page But Date amp Time settings are not applied automatically because they may critically affect the file system of the recorded HDD To apply Date Time settings confirm settings with Apply Date Time button 24 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 1 2 Recording Its recording values are applied to all 8 channels for all time periods Quick Set Camer Normal Rec Alarm Rec Rel 22 7 Gwen my gt Date Time Configuration Status Macro Setup Channel Status On T T ect a Speed ips 45 Quality 1 05 Best Audio Recording On Seme or all of the recording condilions are currently configured under Mermal or Alarm Rec Menu Button control Press MENU button and select to Recording from the Quick Setup tab Configuration Status Displays the recording set up status If recording is configured with the Quick Setup Macro Setup will be displayed If recording is configured withthe Normal and Alarm recording Custom Setup will be displayed lt Note gt When all 8 analog cameras normal recording conditions are set identically the status is marked as Macro Setup Otherwise it is marked as Custom Setup
28. is connected on xDSL line Network fT User ID Password When ELX8 60 is connected to xDSL access ID and Password should be entered Status Displays the ELX8 60 connection status 46 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 7 7 3 HRS When ELXS 60 is installed under the environment of Cable Modem or xDSL Modem connection its IP address changes whenever it reconnects to the Internet Service Provider the ELX8 60 has a Dynamic or Floating IP address In this case users who don t know the changed IP address cannot get access to the ELX8 60 ELX6 60 with dynamic IP should be registered to the RUGGED CCTV Registration Server HRS server in order to make it easy for users to find the changed IP address when they want to access the ELX8 60 To register dynamic IP address to HRS configure the descriptions below If using xDSL modem or Cable modem configuration should be the same Iul lE A ucc E Alarm Rec Relay Monitor Utility Text WRS Interval Time Schedule WRS URL Audio Special Time Group ID DVR Security Status Hot Registered Disk Setup Serial Setup Miscellaneaus Configure DVR RS settings L HRS Interval HRS Interval should be set at 3600 seconds This designates the frequency the ELX8 60 will update information to the HRS If the interval is set lower than 3600 seconds Rugged CCTV cannot guaran
29. is no need to format again F Connected but not available file system After using Add need to format to make HDD available for recording Connected ad undergone the Add command HDD needs to be formatted to be available for recording X HDD cable is not connected or HDD has a problem It is recommended to delete from list using Confirm Removed 56 2003 08 13 v 1 0 Rugged CCTV Advanced Configuration ELXS 60 Advanced Configuration 6 Connecting Extemal Device 6 1 Using Text Device In order to use text device the following four menus should be set Text menu Serial Setup s RS232 menu Alarm Rec menu Normal Rec menu 6 1 1 Setting at Text menu Alarm Rec Relay Monitor CD Utility Audio Recording On Time Schedule Sync Text With All Special Time Device Star Finger 007 Security Disk Setup Network Serial Setup Text configuration Set both Recording and Monitoring as Set Sync Text with value If the connected device is Star Finger 007 select it at Device menu If not set Manual and each sub menu Rugged CCTV 2003 08 13 v 1 0 57 ELX8 60 Advanced Configuration 6 1 2 Setting at Serial Setup s RS232 menu Serial Setup Set RS232 s device menu as Text And set baud rate parity stop and data 6 1 3 Setting at Alarm Rec menu Alarm Rec WE Custom Area Y aL ui ksA GSe
30. l recommendations against the environmental pollution Important Notice 1 Do not place heavy objects on the top of the ELX8 60 2 ELX8 60 is not weatherproof In case of outdoor use equip a weatherproof case to protect ELX8 60 from water moisture or temperature higher or lower than specifications To clean the ELX8 60 gently wipe the outside with a clean dry cloth 3 Be sure to use a DC adapter that is provided by Rugged CCTV Connecting ELX8 60 directly to an AC current will cause electric damages to ELX8 60 4 Be careful not to drop the ELX8 60 Physical shocks may harm the product In addition be sure the ELX8 60 is secured after installation 5 ELX8 60 is made of metal Therefore you can hurt human beings if yu throw it to them or hit on them When installing ELX8 60 be cautious to locate on safe places where children are unreachable 6 If ELX8 60 does not operate properly please contact the closest Rugged CCTV distributor for after sales service Tampering or disassembling the product will void the warranty 7 Security surveillance laws may differ for each country Therefore please contact the local region first to avoid any surveillance law violations 4 TABLE OF CONTENTS TABLE OF CONTENTS OVERIVEW 6 16 tal 6 2 Product Description 8 229 51611 ER
31. light Savings For example selecting GMT 7 00 Arizona will disable the option for Daylight Savings because Daylight Savings is not used in Arizona This menu is linked with Time Zone menu Namely if selecting daylight saving area in time zone this menu will be activated Oppositely if selected time zone is not enforced it will not be It is based on MS Windows So this menu is for setting whether you apply ON OFF with left right arrow button on ELX8 60 front panel in daylight saving area Sync with NTP It is to synchronize time with NTP Network Time Protocol server For more detailed information about NTP setting please refer to the Network Configuration System gt Network gt NTP Settings Rugged CCTV 2003 08 13 v 1 0 23 ELXS 60 Basic Configuration Time Format Set the time format between MM DD Y Y YY and using the left right arrow button on ELXS 60 front panel Date Time Set date and time To move from Month to Day to Year Hour to Minute use the left right arrow buttons To select each month each day etc use the up down arrow buttons Apply Date Time Press this button to confirm the above settings An window will pop up warning of the possibility of time conflict with recorded images It is strongly recommended to format the HDD after making changes to the time menu WARNING Changing DVR time may cause time conflict with previous images If times are duplicated by sett
32. me zone will be set as UTC 00 00 Dublin Set the time to local time zone Changing ELX8 60 time may cause time conflict with recorded images In this case it is strongly recommended to re format the hard drives after making changes Button control gt Press MENU button on ELXS 60 front panel Move to Setup menu First tab on the Configuration menu Move to Date Time below Quick Setup using downward arrow button on ELX8 60 front panel Press the ENTER button on ELX8 60 front panel Set time The following picture will be displayed when setting time menu In order to access each menu press ENTER button after selecting it with upward downward arrow button on ELX8 60 front panel 22 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 Date Time Time Zone A Recording Daylight Saving on Sync with NTP Time Format MMDD YYYY Date 04 01 2003 Time 09 57 Apply DateTime Configure system time and date Time Zone Set the time zone using the left right arrow button ELX8 60 front panel Every time you press left right arrow button time zone will change Select the desired time zone move to the previous menu press EXIT button on ELX8 60 front panel Daylight Saving The Daylight Savings option is linked to Time Zone Daylight Savings is only activated for time zones that use Day
33. n be designated as Special Time Event Recording Press the ENTER button to access the Event Recording feature Set On Off using the or buttons Event recording condition is set under the Alarm Recording tab This setting is used to configure the ELX8 60 to record data according to an alarm condition such as Motion Detection MD sensors etc 32 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 4 Alarm Rec This menu is to configure for the settings for alarm recording conditions To activate this schedule set Event Recording under the Normal Recording tab to On d Quick Setup Camera Normal Ree CUTS Relay Low MD Area Select Area Cami3 Si on 52 4 51 32 Text On Camis Recording Speed Quality High Speed ips 77 7 Quality 9 05 Best Cami8 Pre Alarmisec P 5 Post Alarm sec Configure Alarm recording schedule for for channel 1 Press Enter to configure MD Choose from among four sensitivity conditions Off Low Standard and High MD Area Customize the MD area Default value is Select Select Custom Area to remove certain blocks from detecting motion Sensor 1 2 3 4 The ELX8 60 will only work with NO Normal Open sensors If sensors are connected turn each sensor 29 Rugged CCTV 2003 08 13 v 1 0 33 ELXS 60 Basi
34. oad Preset To load preset for dome camera during live monitoring mode Press the SELECT button Move the Select icon to the desired channel Press the MENU button Select Load Preset from the PTZ Menu Press number button for desired preset on the front panel Save Preset To set a new preset point for dome camera during live monitoring mode Move dome camera to the desired position using the Pan Tilt and Zoom Focus menus Press the SELECT button Press the MENU button Select Save Preset from the PTZ Menu Designate a number for the preset position by pressing a number button on the front panel 14 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 3 8 Using Relay To set relay on off ELX8 60 supports four relay outputs Press the SEARCH RELAY button The icon of Relay On shows Press the relay number button between 1 and 4 and then the related relay out signal will be transmitted In order to set relay off press the SEARCH RELAY button again Then Relay On shows because relay keeps being set as on Press the SEARCH RELA Y button again and then the icon of Relay Off will show Press the relay a number button to set off 3 9 Using Screen Lock To set screen lock For this function user password should be set at first If pressing the EXIT LOCK button for 2 3 seconds lock mode will run with showing Sc
35. ode Search Mode is used to search and play specific data directly during playback mode Data can be searched by specific Time and Date or by the Event Log browser a Date 2003 04 01 Time 11 00 00 Log Browser 2003 04 01 10 32 20 Rec Stopped Button control Press the SEARCH button during playback mode Search for data by entering Date Time or by selecting an event from the Event Log browser Press the ENTER button after entering the desired Date Time or selecting Event from log The selected images will begin to playback To exit from search mode press the EXIT button Note Using Log Browser To move to theprevious next page press the Left or Right buttons 2 To move to previous log entry press the Up button 3 To move to next log entry press the Down button 18 2003 08 13 v 1 0 Rugged CCTV Basic Configuration 4 3 Copy Backup Delete Data Manager To copy backup delete the recorded data This menu is activated during playback mode Copy Image Backup data Delete data Press the SELECT button and MENU button in Playback mode 4 3 1 Copy Data To copy a specific data with USB memory stick Copy Images Seconds 5 Size KB Start Seconds To designate copy range between and 60 seconds Select Disk Select copy disk Rugged CCTV 2003 08 13 v 1 0 ELXS 60 19 ELXS 60 Basic Configuration 4 3 2
36. on 750hm Set video input impedance using the or buttons after pressing the ENTER button Type Displays the video input signal NTSC is the signal used in North America To toggle the setting use dip switch on the rear panel of ELX8 60 Color Set Color B W using the or buttons Gain Brightness Contrast Set the value between 9 and 9 using the or buttons PTZ Port Set the value using the or buttons Address Press the ENTER button to open the dialogue box Rugged CCTV 2003 08 13 v 1 0 29 ELXS 60 Basic Configuration 5 3 Normal Rec This menu is for configuring the normal recording settings based on channel and timetable If this menu is configured Quick Setup the previous Quick Setup values will be replaced the Normal Recording settings Time Schedule Each camera can be set to record based on four time schedules Weekday Day Weekday Night Weekend Day Weekend Night Each schedule can be configured under the System tab 30 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELX8 60 lt Setting Time Schedule gt In order to set time schedule move to System menu Alarm Rec Relay Monitor Utility Audio Weekday Start Mon Text Weekday End Fri Special Time Day End 18 00 Security Disk Setup Serial Setup Designate times tor Weekday Start End and Day Start End Press Enter to
37. ord s plug in a wall outlet and turn the power switch LED is on and ELX8 60 starts booting After start up the basic screen quad split 1s displayed f user password is set a dialogue box for entering the password will appear 3 2 Viewing single full screen Press the desired channel number button on the front panel of ELX8 60 To return to the multi view screen press the MULTI button 3 3 Viewing multi screen Press the MULTI button to view several channels simultaneously To change the split screen configuration press the MULTI button 4 or 9 split screens will be displayed Rugged CCTV 2003 08 13 v 1 0 11 ELXS 60 Basic Configuration 3 4 Viewing all channels with sequence mode All channels can be viewed in successive order automatically using the SEQ button Press the MENU button on the front panel to set up the sequential cycle The default value is 3 seconds per channel for display Select Monitor tab of Configuration menu Move to Configuration below Monitor using the down arrow button on ELX8 60 front panel Select Seq Switching sec and press the ENTER button Set any value between 1 and 60 seconds Rm Alarm Pop up On 1 5 Pop up Hold sec Configure display preferences for real time channel switching Press Enter to configure Then press the SEQ button from any viewer mode l
38. ork ID xxx xxx xxx 128 Gateway Address xxx xxx xxx 129 Subnet Mask 255 255 255 192 Broadcast Address 191 IP Addresses xxx xxx xxx 130 xxx xxx xxx 190 Sub Network ID xxx xxx xxx 192 Gateway Address xxx xxx xxx 193 Subnet Mask 255 255 255 192 Broadcast Address 255 IP Addresses 194 xxx xxx xxx 254 2003 08 13 v 1 0 Rugged CCTV APPENDIX ELXS 60 Rugged CCTV 2003 08 13 v 1 0 69 ELX8 60 70 2003 08 13 v 1 0 APPENDIX Rugged CCTV APPENDIX ELXS 60 Rugged CCTV 2003 08 13 v 1 0 71 ELX8 60 APPENDIX gt Rugged CCTV Industrial Grade Digital Rugged CCTV 5327 Cedar Creek Dr Kemp Texas 75143 Tel 866 301 2288 Fax 903 498 8989 Technical Support 1 866 301 CCTV URL www rugged cctv com E mail sales rugged cctv com
39. pplied NET Displays the status of Ethernet connection and rate of communication When blinking data being transmitted or received over the Ethernet REC Displays image recording status The rate of blinking indicates the speed of recording 1 6 When blinking rapidly ELX8 60 is recording at a high rate when blinking slower the ELX8 60 is recording at a lower rate PLAY Displays playback status The rate of blinking indicates the speed of playback i e When blinking rapidly ELX8 60 is playing back at a high rate when blinking slower ELX8 60 is playing back at a lower rate 4 Function selection button SEQ To select Sequencing Mode ELX8 60 will automatically display all connected channels in successive order MULTI To select the multi channel display 4 9 divided screen SELECT To select video channel for PTZ control in Monitor mode and for Copy Backup Delete in Playback mode ZOOM To activate the digital zoom single channel mode only RELAY SEARCH To search the recorded image in Playback mode or to toggle the Relay On Off function in Monitoring mode 8 2003 08 13 v 1 0 Rugged CCTV OVERVIEW ELXS 60 5 Direction Replaying Button MENU To set PTZ and access Configuration menu ENTER To enter and confirm the selected menu To change the image information display Date Transfer speed etc EXIT LOCK To exit form the selected menu or lock current screen A
40. reen Locked message If lock mode runs any function button will not be operated order to cancel lock mode user password should be ent ered Rugged CCTV 2003 08 13 v 1 0 15 ELXS 60 Basic Configuration 4 Playback To replay recorded images in full screen or quad split screen modes 4 1 Playback via various mode 4 1 1 Playback via basic screen full screen Press the Play button during monitoring mode Play button will begin playback of the last 30 seconds of recorded video at speed Note When pressing the play button in mult monitoring mode channel 1 is always the channel displayed More specifically images recorded on Channel 1 during the last 30 seconds are always displayed However pressing the playback button in single channel monitoring mode will display the selected channel To display another channel press the corresponding number button on the front of ELX8 60 4 1 2 Playback via quad split screen Press the MULTI button during basic single channel playback mode Channels 1 to 4 will be displayedin the quad split screen To display a single channel press the corresponding number button on front of the ELX8 60 4 1 3 Playback ch5 to ch8 via quad split screen Press the SELECT button in quad split mode Select a split position If selecting a channel number the related image is played in the position 4 1 4 Playback with Digital Zoom Pr
41. t Note gt Sequence mode canrun only when connected and activated cameras are more than split screen With single full screen mode activated cameras should be two or more With quad split screen mode there should be five or more activated cameras With 9split screen mode there should be ten or more activated cameras SEQUENCE MODE ONLY SUPPORTS 4 AND 9 SPLIT SCREENS Channel order cannot be changed For example with quad split screen Ch 1 2 3 4 are displayed and then Ch 5 6 7 8 are displayed To end sequence function press the SEQ button 12 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 3 5 Viewing an alarm triggered channel When an alarm is triggered the related channel will pop up full screen automatically Set Alarm Pop up Screen function to On in Configuration under the Monitor tab and set the display durationin Pop up Hold If more than one channel is triggered by an alarm the related channels will be displayed simultaneously in a split screen In order to move current screen press any button 3 6 Viewing images with Digital Zoom In Single Full Screen mode live and recorded images can be expanded using the Digital Zoom feature To enable the digital zoom press the ZOOM button Digital Zoom will expand the image to twice its normal size Default location of the digital zoom inthe center of screen The zoom box can be moved each 10 step
42. t use R3232 communication Set RS232 s device menu as Keyboard And set baud rate parity stop and data 6 2 2 Setting at Serial Setup s PTZ menu Set PTZ camera to control with keyboard For more detailed technical solution please contact the closest local distributor 60 2003 08 13 v 1 0 Rugged CCTV APPENDIX ELXS 60 Rugged CCTV 2003 08 13 v 1 0 61 ELX8 60 1 Technical Specification Hardware Storage Device Image Quality Control Image Compression Video Channel Recording Performance on 360X243 Analog Ch Schedule Recording Matrix Digital Output Schedule Configurable Recording Conditions Pre Post Alarm Recording 62 APPENDIX 32bit RISC Embedded processor 200MIPS Flash memory 8Mbyte RAM 32Mbyte OS Embedded Linux Int 2 HDD bays Ext 3 IEEE 1394 FireWire connection ports Supports Disk Management Tool for all disks Reboot is required when HDD changed Total manageable capacity 2 TB 5 Levels Q1 Q5 Compression Algorithm Differential Wavelet Compression Rate 20 1 500 1 Average file size 3 5KB Standard Quality NTSC or PAL video format are supported ACh analog video inputs via BNC connector Max 60fps NTSC 50fps PAL in total Max 30 fps NTSC per channel if 2ch used 15 NTSC per channel if 4ch used Daily Day night Four segment time frame Weekly Weekdays Weekends Status Normal Event Daily D
43. tee connectivity If the HRS received too many updates it may close the connection to the unit The HRS maintains registered units on the server list for two days If no signal is received before two days the HRS will delete the unit from the register HRS URL This is to configure a server address for registration Rugged CCTV 2003 08 13 v 1 0 47 ELXS 60 Basic Configuration Group ID Group ID is for discriminating and managing the information received by the HRS from the ELX8 60 belonging to group The group ID should be unique to avoid unauthorized access to the ELX8 60 Unauthorized users will not be able to access the ELXS 60 unless they have a login name and password but they will be able to see the unit on their registration list Feecer Ee ond irepl an DVR IManazer accesses ES gets IP addresces of Tezktered Grow Status Displays the registration status of the ELX8 60 48 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 5 7 7 4 Port Setting Alarm Rec Rela System Utility Ten Port Setting 3 A Audio Text a Monitoring Port 8001 Time Schedule Playback Port 8105 Special Time TP Server Port 7119 Firewall Disable Disk Setup Serial Setup Miscellaneous Configure port setting for Monitoring Port Playback Port ELX8 60 uses 800
44. the 10 button of remote controller until ELX8 60 reacts If remote controller s ID agrees with ELXS 60 s all the LEDs on the front panel of the ELX8 60 will light up and a buzzer will sound OSD menus can now be set with the remote controller 52 2003 08 13 v 1 0 Rugged CCTV Basic Configuration ELXS 60 Keyboard Control Addr To set keyboard s control address in order to operate all ELX8 60 s menus with keyboard Default value is 32 If several ELX8 60s are connected with one keyboard it can be collided Then the default value should be changed Keyboard PTZ Addr To set keyboard s PTZ address in order to operate each PTZ camera with keyboard If setting just first camera s address of each ELX8 60 another cameras are designated automatically For example ELX8 60 has five cameras and 2 ELX8 60 has six cameras keyboard PTA address of ELX8 60 should be set 1 and one of 2 ELX8 60 be set as 6 Be cautious that PTZ addressed are assigned to all cameras automatically in spite of non PTZ camera DVR ID For use with the DVR Manager to control and manage several ELX8 60s Alarm Buzzer Enables an alarm buzzer when an alarm MD or sensor is triggered Language To selectthe language used for the OSD Menu Reset Values To reset current configured values To reset DVR press the Reset Values button Rugged CCTV 2003 08 13 v 1 0 53 ELXS 60 Basic Con
45. to the Internet Currently used IP addresses are limited And there are 5 classes networks in the world for now and a network contains lots of IP addresses A network can hold limited IP addresses The numbers depend on network class 5 classes are from A to and the most common one 15 class network 2 2 IP construction and Network class 1 IP construction XXX XXX XXX XXX xxx 0 255 X1 X2 X3 X4 2 Network class A class A network that contains IP addresses from 0 to 127 at room X1 Network ID X1 Host ID X2 X3 X4 Total number of A class networks is 128 in the world B class A network that contains IP addresses from 127 to 191 at room XI Network ID X1 X2 Host ID X3 X4 Total number of B class networks 15 65 534 in the world C class A network that contains IP addresses from 192 to 223 at room Network ID X1 X2 X3 Host ID X4 t is most common network in the world the total number of Cclass networks 15 2 097 152 D class A network that contains IP addresses from 224 to 239 at room X1 D class network is for multicasting and it is not allowed to use for common users E class A network that contains IP addresses from 240 to 225 at room X1 E class network is reserved Rugged CCTV 2003 08 13 v 1 0 65 ELX8 60 APPENDIX 2 3 C class Network 1 Features of Addresses IP address Three digits number in room X4 are for Host ID
46. ton amp IR Remote controls video channels as well On the screen PTZ control on PC Preset 8 points per channel Group 1 group per channel Return Home Position support Software controlled 4 sensor inputs Software controlled 4 alarms outputs 2003 08 13 v 1 0 63 ELX8 60 Audio Recording and Playback Network Simultaneous User Support over Network Management and Firmware Upgrades Security Power Supply included Power Consumption with 2 HDDs Environmental Spec 64 APPENDIX Input 1Ch line in 1 Vpp Output 1Ch line out 1 Vpp Level 7 8 Recording level control Support 20dB Amp for low level audio recording Supports local and remote audio monitoring Protocol TCP IP ARP ICMP DHCP PPPoE Line 10 100Mbps Ethernet RJ 45 Monitoring Max 5 users Playback Max 5 users Firmware upgrades via Network Password User or Administrator Authentication Watermarking For image copying Input AC 100 240V 50 60 Hz Output DC 12V 5A Booting Max DC 12V 10 4 5A 54W Normal DC 12V 1090 3 9A 35W Operating 41 113 degrees F Storage 49 149 degrees F 2003 08 13 v 1 0 Rugged CCTV APPENDIX ELXS 60 2 Utilizing IP Addresses on Local Network 2 1 Introduction Most of our businesses are done via Internet lately We play with information by transmitting through e mails and searching the world of Internet IP address is what we utilize to access
47. ubnet Mask 255 255 255 128 Broadcast Address xxx xxx xxx 127 IP Addresses xxx xxx xxx 2 xxx xxx xxx 126 Sub Network ID xxx xxx xxx 128 Gateway Address xxx xxx xxx 129 Subnet Mask 255 255 255 128 Broadcast Address xxx xxx xxx 255 IP Addresses xxx xxx xxx 130 xxx xxx xxx 254 3 To use as three sub networks 1 4 1 4 1 2 Sub Network ID xxx xxx xxx 0 Gateway Address xxx xxx xxx 1 Subnet Mask 255 255 255 192 Broadcast Address xxx xxx xxx 63 IP Addresses 2 62 Sub Network ID xxx xxx xxx 64 Gateway Address xxx xxx xxx 65 Subnet Mask 255 255 255 192 Broadcast Address xxx xxx xxx 127 IP Addresses 66 126 Sub Network ID xxx xxx xxx 128 Gateway Address xxx xxx xxx 129 Subnet Mask 255 255 255 128 Broadcast Address 255 IP Addresses xxx xxx xxx 130 xxx xxx xxx 254 Rugged CCTV 2003 08 13 v 1 0 67 ELX8 60 APPENDIX 68 4 To use as four sub networks 1 4 1 4 1 4 1 4 Sub Network xxx xxx xxx 0 Gateway Address 1 Subnet Mask 255 255 255 192 Broadcast Address xxx xxx xxx 63 IP Addresses 2 62 Sub Network ID xxx xxx xxx 64 Gateway Address xxx xxx xxx 65 Subnet Mask 255 255 255 192 Broadcast Address xxx xxx xxx 127 IP Addresses 66 126 Sub Netw
Download Pdf Manuals
Related Search