Jazzy Sport 2 - Pride Mobility Products
Contents
1. SPORT 2 OWNER S MANUAL Mobility Products Corp www pridemobility com SAFETY GUIDELINES iN A N WARNING An authorized Pride Provider or a qualified technician must perform the initial setup ff Of this power chair and must perform all of the procedures in this manual The symbols below are used throughout this owner s manual and on the power chair to identify warnings and important information It is very important for you to read them and understand them completely JX WARNING Indicates a potentially hazardous condition situation Failure to follow designated A N procedures can cause either personal injury component damage or malfunction On the product this icon is represented a black symbol a yellow triangle with a black border 6 actions can cause personal injury and or equipment damage2. Product Serial Jazzy Sport 2 I NFMANU45 4 2
3. On the product this icon is represented as a white symbol a blue dot with a white border S PROHIBITED These actions are prohibited These actions should not be performed at any time MANDATORY These actions should be performed as specified Failure to perform mandatory or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle and red slash INTENDED USE The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated position that have the capability of operating a powered wheelchair Quick Reference Information Authorized Pride Provider Address Phone Number Purchase Date NOTE This owner s manual is compiled from the latest specifications and product information available at the time of publication We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased The latest current version of this manual is available on our website NOTE This product is compliant with WEEE RoHS and REACH directives and requirements NOTE The Jazzy Sport 2 and its components are not made with natural rubber latex Consult with the man ufacturer regarding any after market accessories CEC Copyr
4. PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings mandatory actions and prohibited actions It is very important for you to read and understand them completely NOTE There are more warnings identified and explained in the Consumer Safety Guide that is included with your power chair Please become familiar with all the warnings and safety information found in the Consumer Safety Guide and refer to this resource often Read and follow the information in the owner s manual Unlocked and in freewheel mode Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode Locked and in drive mode Class Equipment Manufactured in Main Frame XXXXXXX Mobility Products Corp www pridemobility com Power chair information label dace Jazzy Sport 2 www pridemobility com 5 11 SAFETY GENERAL GUIDELINES N MANDATORY Do not operate your new power chair for the first time without completely reading U and understanding this owner s manual Your power chair is a state of the art life enhancement device designed to increase mobility Pride provides an extensive variety of products to best fit the individual needs of the power chair user Please be aware that the final selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user w
5. Sport 2 www pridemobility com 21 VII CARE AND MAINTENANCE wheel bearings are prelubricated and sealed They require no subsequent lubrication The body shroud has been sprayed with a clear sealant coating You can apply a light coat of car wax to help it retain its high gloss appearance Check all electrical connections Make sure they are tight and are not corroded Batteries must sit flat within the battery boxes and battery well frame with the battery terminals facing inward toward each other Refer to the battery wiring label for the correct wiring layout WARNING Even though the power chair has passed the necessary testing requirements for ingress of liquids you should keep electrical connections away from sources of dampness including direct exposure to water or bodily fluids and incontinence Check electrical components frequently for signs of corrosion and replace as necessary Daily Checks With the controller turned off check the joystick Make sure it is not bent or damaged and that it returns to the neutral position when you release it Check the rubber boot around the base of the joystick for damage Visually inspect the boot Do not handle or try to repair it See your authorized Pride Provider if there is a problem Visually inspect the controller harness Make sure that it is not frayed cut or has any wires exposed See your authorized Pride Provider if there is a problem Check for flat spo
6. in A WARNING Do not service the power chair when the seat is occupied 4 a Your power chair like most electrical equipment is susceptible to damage from the elements Avoid damp areas of any kind WARNING Direct or prolonged exposure to water or dampness could cause the IR A power chair to malfunction electronically and mechanically Water can cause electrical components to corrode and chair s frame to rust Power chairs should be examined periodically for signs of corrosion caused by water exposure bodily we fluids exposure or incontinence Damaged components should be replaced or treated immediately Should your power chair come in contact with water 1 Dry your power chair as thoroughly as possible with a towel 2 Allow your power chair to sit ina warm dry place for 12 hours to allow unseen water to evaporate 3 Check the joystick operation and the brakes before using your power chair again 4 If any inconsistencies are found take your power chair to an authorized service center Power chairs that are frequently exposed to sources of water such as incontinence should be inspected often for corrosion and electronic components may need to be replaced frequently Temperature Some of the parts of your power chair are susceptible to extreme changes in temperature Always keep your power chair between the temperatures of 18 F 8 C and 122 F 50 C In
7. of the foot platform See figure 11 To adjust the foot platform angle 1 Flip up the foot platform and locate the adjustment screw 2 Turn the adjustment screw to raise or lower the front of the foot platform SETSCREW Figure 11 Foot Platform Angle Adjustment 14 www pridemobility com Jazzy Sport 2 V COMFORT ADJUSTMENTS Swing away Footrests Swing away Footrests SFRs enable you to rotate the footrests to the side before you transfer onto or off of your power chair See figure 12 To rotate the SFRs 1 Push in the release lever 2 Rotate the SFRs To adjust the SFR length 1 Remove the adjustment screws from the footrest extension 2 Slide the footrest up or down to the desired length 3 Reinstall the two adjustment screws Elevating Leg Rests Elevating Leg Rests ELRs offer an infinite range of adjustment for the leg angle and a footrest adjustment range of 12 19 in 30 48 48 26 cm See figure 13 To rotate the ELRs 1 Push in release lever A 2 Rotate the ELRs To adjust the ELR angle 1 Push down release lever B 2 Move the leg rest to the desired angle To adjust the ELR length 1 Remove the two adjustment screws from the side of each leg rest extension 2 Slide the leg rest up or down to the desired length 3 Reinstall the two adjustment screws Jazzy Sport 2 www pridemobility com SFR RELEASE LEVER FOOTR
8. throughout periods of prolonged storage to ensure proper performance You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of prolonged storage This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the tires contacting the ground Disposal of Your Power Chair Your power chair must be disposed of according to applicable local and national statutory regulations Contact your local waste disposal agency or authorized Pride Provider for information on proper disposal of power chair packaging metal frame components plastic components electronics batteries neoprene silicone and polyure thane materials Cleaning and Disinfection E Use a damp cloth and mild non abrasive cleanser to clean the plastic and metal parts of your power chair Avoid using products that may scratch the surface of your power chair If necessary clean your product with an approved disinfectant Make sure the disinfectant is safe for use on your product before application WARNING Follow all safety instructions for the proper use of the disinfectant and or cleaning agent before applying it to your product Failure to comply may result in skin irritation or premature deterioration of upholstery and or power chair finishes WARNING Never hose off your power chair or place it in direct contact with water Your power chair has a painted ABS plasti
9. with your power chair See figure 3 CONTROLLER HARNESS BATTERY CONNECTORS 5 MOTOR CONNECTORS MAIN CIRCUIT BREAKER Figure 3 Jazzy Sport 2 Electrical Components Jazzy Sport 2 www pridemobility com 9 lll YOUR POWER CHAIR Manual Freewheel Levers Your power chair has a manual freewheel lever on each motor Manual freewheel levers enable you to disengage the drive motors from the gearboxes and maneuver the chair manually WARNING Do not use the power chair while the drive motors are disengaged Do not disengage the drive motors when the power chair is on an incline or decline as the unit could roll on its own Only engage the freewheel mode when on a level surface SaN WARNING It is important to remember that when your power chair is in freewheel A mode the braking system is disengaged To engage or disengage the drive motors 1 Locate the lever on the top of the power base 2 Push both levers forward away from the seat post to engage the drive motors drive mode See figure 4 3 Pull both levers rearward toward the seat post to disengage the drive motors freewheel mode See figure 5 If a lever is difficult to move in either direction slightly rock the power chair back and forth The lever should then move to the desired position FREEWHEEL LEVERS Figure 4 Drive Mode Drive Engaged Figure 5 Freewheel Mode Drive Disengaged 10 www pridemobility com Jazz
10. 5 Remove the drive wheel from the axle Make sure that you keep the key 6 Replace the entire assembly 7 Slide the wheel back onto the axle Make sure that the key is in the axle slot DRIVE WHEEL WASHER WARNING Ensure that the axle key is properly installed into the axle slot when DRIVE WHEEL NUT JN mounting the wheel If not installed A securely the braking system disengaged which may cause personal Figure 16 Jazzy Sport 2 Drive Wheel Removal injury and or product damage may result 8 Reinstall the drive wheel nut and washer onto the axle and tighten See figure 16 A WARNING Make sure both the nut and the washer are reinstalled and tightened properly Remove the power chair from the base support Battery Replacement A battery wiring diagram is printed on a decal located on the power base See VI Batteries and Charging for correct battery specifications Pb am MANDATORY Battery posts terminals and related accessories contain lead lead compounds Wear goggles and gloves when handling batteries and wash hands Lead after handling WARNING The batteries in your power chair should only be serviced or replaced by an authorized Pride Provider or a qualified technician WARNING Do not replace batteries when seat is occupied JX WARNING Power chair batteries are heavy See specifications table If you are K unable to lift that much weight be sure to g
11. Avoid temperature extremes such as freezing and excessively hot conditions and never attempt to charge a frozen battery A cold or frozen battery should be warmed for several days prior to recharging What about public transportation AGM and Gel Cell batteries are designed for application in power chairs and other mobility vehicles These batteries are Federal Aviation Administration FAA approved allowing safe transportation on aircraft buses and trains as there is no danger of spillage or leakage We suggest you contact the carrier s ticket counter in advance to determine that carrier s specific requirements What about shipping If you wish to use a freight company to ship your power chair to your final destination repack your power chair in the original shipping container and ship the batteries in separate boxes 20 www pridemobility com Jazzy Sport 2 VII CARE AND MAINTENANCE CARE AND MAINTENANCE Your Jazzy Sport 2 is a sophisticated power chair Like any motorized vehicle it requires routine maintenance checks You can perform some of these checks but others require assistance from an authorized service represen tative Preventive maintenance is very important If you follow the maintenance checks in this section as sched uled you can help ensure that your power chair gives you years of trouble free operation If you have any doubt as to your power chair s care or operation contact your authorized Pride Provider
12. EST EXTENSION ADJUSTMENT SCREWS RELEASE LEVER A RELEASE LEVER B LEG REST EXTENSION ADJUSTMENT SCREWS Figure 13 Elevating Leg Rests V COMFORT ADJUSTMENTS Positioning Belt Your power chair may be equipped with a positioning belt that can be adjusted for operator comfort See figure 14 The positioning belt is designed to support the operator so that he she does not slide down or forward in the seat The positioning belt is not designed for use as a restraining device WARNING The positioning belt is not designed for use as a seat belt in a motor vehicle Nor is your power chair suitable for use as a seat in any vehicle Anyone traveling in a vehicle should be MaN properly belted into seats approved by ff the vehicle manufacturer WARNING The positioning belt should be secured at all times Never allow the positioning belt to hang or drag on the floor as it may become entangled To install the positioning belt Figure 14 Positioning Belt Adjustment 1 Remove the rearmost screw that holds the seat hinge to the seat base on both the left and right seat hinges 2 Insert the screw through the supplied washer through the positioning belt and into the seat base for each side of the power chair seat 3 Tighten both screws To adjust the positioning belt for operator comfort 1 Once seated insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a
13. VER CASTER WHEEL ANTI TIP WHEELS Figure 2 The Jazzy Sport 2 Power Base 8 www pridemobility com Jazzy Sport 2 lll YOUR POWER CHAIR Electrical Components The electrical components are located either on or inside the power base The main circuit breaker is located on the front of the power base The power module is located under the front cover See figure 3 Main Circuit Breaker The main circuit breaker is a safety feature built into your power chair When the batteries and the motors are heavily strained e g from excessive loads the main circuit breaker trips to prevent damage to the motors and the electronics If the circuit trips allow your power chair to rest for approximately one minute Next push in the circuit breaker button turn on the controller and continue normal operation If the main circuit breaker continues to trip repeatedly contact your authorized Pride Provider Power Module Provides connection between the controller and the motors and batteries The GC3 control system supplied with your power chair has been factory set to operate within safe limits for speed acceleration deceleration dynamic stability and braking The system is not programmable Contact your authorized Pride Provider with any questions regarding the operation of your power chair All components their connections and function are identical to the information supplied in the controller basic operating instruction provided
14. batteries of the exact same type chemistry and amp A hour Ah capacity Refer to the specifications table and the manual supplied with the battery charger for recommended type and capacities WN WARNING Contact your authorized Pride Provider if have any questions A N regarding the batteries in your power chair Charging the Batteries The battery charger is essential in providing long life for your power chair batteries It is designed to optimize your power chair s performance by charging the batteries safely quickly and easily The battery charger is only functional when the charger power cord is plugged into an electrical outlet KON PROHIBITED Removal of grounding prong can create electrical hazard If necessary properly install an approved 3 pronged adapter to an electrical outlet NX having 2 pronged plug access fs PROHIBITED Never use an extension cord to plug in your battery charger Plug the charger directly into a properly wired standard electrical outlet ne PROHIBITED not allow unsupervised children to play near the power chair while the batteries are charging Pride recommends that you do not charge the batteries Nae while the power chair is occupied N MANDATORY Read the battery charging instructions in this manual and in the U 21 manual supplied with the battery charger before charging the batteries A WARNING Explosive gases may be generated whi
15. c body shroud that allows it to be easily wiped clean with damp cloth WARNING Never use any chemicals to clean a vinyl seat as they may cause the seat to become slippery or dry out and crack Use soapy water and dry the seat thoroughly Wheel Replacement If you have pneumatic tires and you have a flat tire replace the tube If your chair is equipped with a solid tire insert then you must replace the whole wheel assembly Replacement tires tubes and wheel assemblies are readily available through your authorized Pride Provider WARNING The wheels on your power chair should only be serviced or replaced by an authorized Pride Provider or a qualified technician aN WARNING Be sure that the power to the controller is turned off and the power chair is not in j N freewheel mode before performing this procedure WARNING When changing a tire remove only the center lug nut and washer then remove the wheel If any further disassembly is required deflate the tire completely or it may explode Jazzy Sport 2 www pridemobility com 23 VII CARE AND MAINTENANCE Follow these easy steps for a quick and safe repair for both pneumatic and solid tires 1 Turn off the power to the controller 2 Make sure that the power chair is in drive mode See figure 4 3 Raise and support the power base so that the wheel is at least 1 in 2 54 cm off of the ground 4 Remove the drive wheel nut and washer from the axle See figure 16
16. click See figure 14 2 Pull the excess strap attached to the metal tab until it is secure but not so tight as to cause discomfort To release the positioning belt 1 Press the push button mechanism on the plastic housing MANDATORY Make sure the positioning belt is properly secured to the power chair and is adjusted for operator comfort before each use G D MANDATORY Inspect the positioning belt for loose parts or damage including tears worn spots bent hardware damaged latch mechanisms dirt or debris before each use of the power chair If you discover a problem contact your authorized Pride Provider for maintenance and repair 16 www pridemobility com Jazzy Sport 2 VI BATTERIES AND CHARGING BATTERIES AND CHARGING Your power chair uses two long lasting 12 volt deep cycle batteries These batteries are sealed and maintenance free Since they are sealed there is no need to check the electrolyte fluid level Deep cycle batteries are designed to handle a longer and deeper discharge Though they are similar in appearance to automotive batteries they are not interchangeable Automotive batteries are not designed to handle a long deep discharge and also are unsafe for use in power chairs Pb MANDATORY Battery posts terminals and related accessories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands or Lead after handling PROHIBITED Always use two
17. e wear See your authorized Pride Provider for repair Check the caster wheels for wear Replace them as necessary Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings replaced See your authorized Pride Provider for repair Check the entire power chair for loose hardware and changes in the function or performance of the power chair See your authorized Pride Provider for repair Keep your power chair clean and free of foreign material such as mud dirt hair food drink etc Yearly Checks Take your power chair to your authorized Pride Provider for yearly maintenance especially if you use your power chair on a daily basis This helps ensure that your power chair is functioning properly and helps prevent future complications 22 www pridemobility com Jazzy Sport 2 VII CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place free from temperature extremes When storing disconnect the batteries from the power chair See VI Batteries and Charging S WARNING If you fail to store the unit properly the frame can rust and the electronics can be 7 damaged Batteries that are regularly and deeply discharged infrequently charged stored in extreme temperatures or stored without a full charge may be permanently damaged causing unreliable performance and limited service life It is recommended that you charge the batteries periodically
18. et help Use proper lifting techniques and avoid lifting beyond your capacity WARNING Do not mix old and new batteries Always replace both batteries at the same time A PROHIBITED Keep tools and other metal objects away from the battery terminals Contact with tools can cause electrical shock 7 A You may need the following to change your batteries metric standard socket set and ratchet E adjustable wrench To replace the batteries 1 Turn off the power to the controller 2 Make sure that the power chair is in drive mode See figure 4 24 www pridemobility com Jazzy Sport 2 4 x lt q Vil CORRECT CONNECTION MAIN SHROUD INCORRECT CONNECTION BATTERY BATTERY YELLOW THUMBSCREWS Negative Black Terminal Post Battery Set Configuration Positive Red Terminal Post S Terminal Post rim Connect to Black Black wire Figure 17 Battery Installation Seat Removed for Clarity 25 www pridemobility com Jazzy Sport 2 VII CARE AND MAINTENANCE Remove the seat Remove the main shroud by lifting the rear of the shroud up and pulling the shroud back See figure 17 Remove the shipping guard if applicable See figure 17 Disconnect the battery cables from the battery terminals of each battery See figure 17 Loosen the yellow thumbscrews and slide the battery t
19. extremely cold temperatures the batteries may freeze The specific temperature at which they freeze depends on a number of factors such as battery charge usage and composition of the batteries e g AGM or Gel Cell Temperatures above 122 50 may cause your power chair to operate at a reduced speed This reduced speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical components General Guidelines Avoid knocking or bumping the controller especially the joystick Avoid prolonged exposure of your power chair to extreme conditions such as heat cold or moisture Keep the controller clean Check all connectors to ensure that they are all tight and secured properly Make sure pneumatic tires are inflated to the psi bar kPa air pressure rating indicated on the tire WARNING Make sure your tires are inflated to the psi bar kPa air pressure rating indicated on the tire for pneumatic tires Do not underinflate or overinflate your tires Low pressure may 7 N result in loss of control and overinflated tires may burst Overinflating tires can cause them to explode WARNING Do not use a high pressure hose to inflate your tires Use a rubber conditioner on the tire sidewalls to help preserve them A WARNING Never use a rubber conditioner on the tread area of the tires doing so may make the jf tires slippery and cause your power chair to skid K Jazzy
20. g the off board charger 1 Position the front of your power chair next to a stan dard electrical outlet See figure 15 2 certain the controller power is turned off and the freewheel levers are in the engaged position See Your Power Chair 3 Plug the off board charger into the off board char ger programming socket on the controller See figure 15 4 Plug the off board charger into the electrical outlet WARNING The LED lights on the charger indicate different charger conditions at various times charger power on charging in progress and charging complete If the LED does not indicate that charging is complete A within 24 hours unplug the charger from the outlet and contact your authorized Pride Provider Refer to the manual supplied with the charger for a complete explanation of these indicators Figure 15 Battery Charging 5 When the batteries are fully charged unplug the off board charger from the electrical outlet and then from the controller Battery Break in To break in new batteries for maximum efficiency 1 Fully recharge any new battery prior to its initial use This brings the battery up to about 90 of its peak performance level 2 Operate your power chair throughout the house and yard Move slowly at first and do not travel too far until you become accustomed to the controls and break in the batteries 3 Give the batteries another full charge of at least 8 to 14
21. ho is capable of making such a decision and his her healthcare professional i e medical doctor physical therapist etc The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair to the user and has assisted the prescribing healthcare professional and or the authorized Pride Pro vider in the instruction process for the use of the product There are certain situations including some medical conditions where the power chair user will need to practice operating the power chair in the presence of a trained attendant A trained attendant can be defined as a family member or care professional specially trained in assisting a power chair user in various daily living activities As you begin using your power chair during daily activities you will probably encounter situations in which you will need some practice Simply take your time and you will soon be in full and confident control as you maneuver through doorways on and off of elevators up and down ramps and over moderate terrain Below are some precautions tips and other safety considerations that will help you become accustomed to oper ating your power chair safely Pre Ride Safety Check Get to know the feel of your power chair and its capabilities Pride recommends that you perform a safety check before each use to make sure your power chair operates smoothly and safely Perform the following inspections prior to using
22. hours and operate your power chair again The batteries will now perform at over 90 of their potential 4 After four or five charging cycles the batteries will top off at 100 charge and last for an extended period Frequently Asked Questions FAQs How does the charger work The battery charger takes the standard electrical outlet voltage of 120 VAC alternating current and converts it to 24 VDC direct current The power chair batteries use direct current to run your power chair When the battery voltage is low the charger works harder to charge the battery As the battery voltage approaches full charge the charger doesn t work as hard to complete the charging cycle When the battery is fully charged the amperage from the charger is nearly at zero This is how the charger maintains a charge but does not overcharge the battery Can use a different battery charger You should use the charger supplied with the power chair It is the safest most efficient tool to charge the batteries We do not recommend using other types of chargers e g an automotive battery charger NOTE Your power chair s charger will not operate after the batteries have been discharged to nearly zero voltage If this happens contact your authorized Pride Provider for assistance How often must I charge the batteries Many factors come into play when deciding how often to charge the batteries You may use your power chair all day on a daily basis or you may
23. ight 2013 Pride Mobility Products Corp INFMANU4542 Rev A August 2013 CONTENTS INTRODUCTION Maal 4 l SAFETY ned 5 II YOUR POWER spear asad Sana Ta ocd 7 IV ASSEMBLY Maen 11 V COMFORT ADJUSTMENTS 12 VI BATTERIES AND CHARGING 17 CARE AND MAINTENANCE ooo 21 Jazzy Sport 2 www pridemobility com 3 Il INTRODUCTION SAFETY WELCOME to Pride Mobility Products Pride The power chair you have purchased combines state of the art components with safety comfort and styling in mind We are confident that these design features will provide you with the conveniences you expect during your daily activities Once you understand how to safely operate and care for your power chair it should give you years of trouble free operation and service Read and follow all instructions warnings and notes in this manual before attempting to operate your power chair for the first time You must also read all instructions warnings and notes contained in any supplemental instruc tional booklets for the controller front riggings and or seating system that accompanied your power chair before initial operation Your safety depends upon you as well as your provider caretaker or healthcare professional i
24. le charging the batteries Keep AN the power chair and battery charger away from sources of ignition such as flames or sparks and provide adequate ventilation when charging the batteries WARNING You must recharge your power chair s batteries with the supplied off board battery charger Do not use an automotive type battery charger WARNING Inspect the battery charger wiring and connectors for damage before each use Contact your authorized Pride Provider if damage is found N WARNING Do not attempt to open the battery charger case If the battery charger 7 does not appear to be working correctly contact your authorized Pride Provider WARNING Be aware that the battery charger case may become hot during charging Avoid skin contact and do not place on surfaces that may be affected by heat WARNING If the battery charger is equipped with cooling slots then do not attempt to insert objects through these slots WARNING If your battery charger has not been tested and approved for outdoor NI use then do not expose it to adverse or extreme weather conditions If the battery charger is exposed to adverse extreme weather conditions then it must be AS 2 W allowed to adjust to the difference in environmental conditions before use indoors Refer to the manual supplied with the battery charger for more information Jazzy Sport 2 www pridemobility com 17 VI BATTERIES AND CHARGING To charge the batteries usin
25. line Seatback Adjustment If your power chair is equipped with a manual recline seatback you can adjust the seatback angle with the seatback release lever The lever is located on the right side of the seat base See figure 9 To adjust the recline angle 1 Pull up on the seatback release lever 2 Lean forward or backward to the desired position 3 Release the lever Armrest Width Adjustment You can change each armrest s width independently of the other NOTE Changing the armrest width may increase the overall width of your power chair To change the armrest width 1 Locate the armrest width adjustment setscrew on each side of the armrest receiver bracket See figure 9 2 Loosen the setscrew 3 Slide the armrests in or out to the desired width 4 Tighten the setscrew Armrest Angle Adjustment To change the armrest angle 1 Lift the armrest straight up so that it is perpendicu lar to the floor 2 Loosen the jam nut 3 Turn the adjustment screw to raise or lower the front of the armrest 4 Tighten the jam nut to lock the adjustment screw into place Armrest Height Adjustment To change the armrest height 1 Loosen the setscrew on the armrest See figure 9 2 Raise or lower the armrest to the desired height 3 Tighten the setscrew to secure the armrest ARMREST ANGLE ADJUSTMENT SCREW SEATBACK RELEASE LEVER ARMRESTHEIGHT ADJUSTMENT oe SETSCREW ARMRESTWIDTH ADJUSTMENT Fig
26. n using good judgement If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation please contact your authorized Pride Provider Failure to follow the instructions in this manual and those located on your power chair can lead to personal injury and or damage to the power chair and may void the warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify this product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product SHIPPING AND DELIVERY Before using your power chair make sure your delivery is complete as some components may be individually packaged If you do not receive a complete delivery please contact your authorized Pride Provider immediately Where damage has occurred during transport either to the packaging or content please contact the delivery com pany responsible Pride Mobility Products Corporation Attn Customer Care Department 182 Susquehanna Avenue Exeter PA 18643 2694 info pridemobility com NOTE If you ever lose or misplace your copy of this manual contact us and we will be glad to send you a new one immediately C T eee 4 www pridemobility com Jazzy Sport 2 11 SAFETY
27. nent weights before you disassemble the power chair WARNING Remove the occupant from the power chair before making any adjustments You may need the following to make comfort adjustments metric standard socket set and ratchet adjustable wrench metric standard hex key set thread lock Seat Height Adjustment You can change the seat height to one of three positions in l in 2 54 cm increments To change the seat height 1 2 3 4 9 10 11 12 Turn off the power to controller Ensure the power chair is in drive mode See figure 4 Disconnect the controller connector from power base See figure 8 Disengage the seat release lever See figure 8 Swivel the seat left or right and then pull it up and off of the power base Loosen the hardware at the rear of the seat post See figure 8 Remove the seat height adjustment bolt washers and nuts from the seat post See figure 8 Raise or lower the upper seat post to the desired position Reinstall the seat height adjustment hardware to the seat post Tighten the hardware at the rear of the seat post Reinstall the seat Reconnect the controller to the power base NOTE To rotate the seat use the seat release lever located under the seat SEAT RELEASE LEVER CONTROLLER CONNECTOR SEAT HEIGHT ADJUSTMENT BOLT Figure 8 Seat Height Adjustment 12 www pridemobility com Jazzy Sport 2 V COMFORT ADJUSTMENTS Manual Rec
28. not use it for weeks at a time 18 www pridemobility com Jazzy Sport 2 VI BATTERIES AND CHARGING Daily Use If you use your power chair on a daily basis charge the batteries as soon as you are finished using your power chair Your power chair will be ready each morning to give you a full day s service It is recommended that you charge the batteries at least 8 to 14 hours after daily use Pride recommends that you charge your batteries for an additional 4 hours after the battery charger indicates that charging is complete E Infrequent Use If you use your power chair infrequently once a week or less you should charge the batteries at least once per week for at least 24 hours NOTE Keep your batteries fully charged and avoid deeply discharging your batteries Refer to the manual supplied with the battery charger for charging instructions Pride recommends charging your batteries for at least 48 continuous hours once per month to improve battery performance and battery life How can I get maximum range or distance per charge Rarely do you have an ideal driving situation such as smooth flat hard terrain with no wind hills or curves More often you are presented with hills sidewalk cracks uneven and loosely packed surfaces curves and wind All of these factors will affect the distance or running time per battery charge Below are a few suggestions for obtaining the maximum range per charge Always charge the batteries full
29. nt controller harness damage Avoid routing the controller harness on the outside of the armrest pad Route the harness under the armrest or N toward the inside of the armrest 4 pad Use correct tie down points N for the controller harness to prevent the harness from getting caught in the drive tires pinched in the seat frame or damaged when passing through doorways 5 Plug the controller harness into the connector on the power base See figure 2 WIRE TIES Figure 7 Controller Harness Routing Jazzy Sport 2 www pridemobility com 11 V COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair s operation you may find the need to make some adjustments to increase your comfort such as seat height armrest angle foot platform angle and controller position Refer to the following information before making comfort adjustments im WARNING The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users Your authorized Pride Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements Do not change your seating configuration without first contacting Pride Mobility Products or your A N authorized Pride Provider A w WARNING Some power chair components are heavy You may need assistance to lift or carry them Please refer to specifications table for specific compo
30. ray back 0 WARNING The battery cables must be disconnected from the battery terminals before sliding N the battery tray back or cable damage could result 8 Lift the front and rear batteries out of the power base 9 Install new batteries into the battery tray Make sure the terminals of each battery are facing the front of the power chair See figure 17 10 Slide the battery tray back into place and tighten the yellow thumbscrews 11 Connect the front battery cable to the front battery terminals according to the battery wiring diagram Make sure that the battery terminal hardware is facing the correct direction See figure 17 12 Connect the rear battery cable to the rear battery terminals according to the battery wiring diagram Make sure that the battery terminal hardware is facing the correct direction See figure 17 WARNING Make sure you tighten the fasteners so that the connections are secure NS gt a K 13 Reinstall the main shroud by aligning slots in front of the shroud with slots in front cover and then sliding the shroud into place 14 Reinstall the seat 15 Charge the batteries See VI Batteries and Charging When to Contact Your Authorized Pride Provider for Service The following symptoms could indicate a serious problem with your power chair If necessary contact your authorized Pride Provider When calling have the model number se
31. rial number nature of the problem and the error code if available Motor noise Frayed harnesses Cracked or broken connectors Uneven wear on any of the tires Jerky motion Pulling to one side Bent or broken wheel assemblies Does not power up Powers up but does not move Loose seator seating components Corrective Maintenance If the battery condition meter does not light up when you turn on the power Check the harness connections Make sure they are tight Check the circuit breaker Reset it if necessary Check the battery connections If the above conditions prove normal you can load test the batteries with a battery load tester These testers are available at automotive parts stores Disconnect both batteries before load testing and follow the directions that come with the load tester If either one of the batteries fails the load test replace both of them If your power chair still does not power up contact your authorized Pride Provider 26 www pridemobility com Jazzy Sport 2 1
32. ts on solid tires Flat spots could adversely affect stability Inspect the seating system armrests and front riggings for loose hardware stress points or damage See your authorized Pride Provider if there is a problem Weekly Checks Inspect the controller and charger harnesses for corrosion Contact your authorized Pride Provider if necessary Ensure that all parts of the controller system are securely fastened to your power chair Do not overtighten any screws Check for proper tire inflation If a tire does not hold air contact your authorized Pride Provider for replace ment of the tube Check the brakes This test should be carried out a level surface with at least 3 feet 1 meter of clearance around your power chair To check the brakes 1 Turn on the controller and turn down the speed level of your power chair 2 After one second check the battery condition meter Make sure that it remains on 3 Slowly push the joystick forward until you hear the electric brakes click Immediately release the joystick You must be able to hear each electrical brake operating within a few seconds of joystick movement Repeat this test three times pushing the joystick backward then left and then right Monthly Checks Check that the anti tip wheels do not rub the ground when you operate the power chair Adjust them as necessary Check for extreme wear on the anti tip wheels Replace them as necessary Check for drive tir
33. ure 9 Armrest and Seatback Adjustments Jazzy Sport 2 www pridemobility com 13 V COMFORT ADJUSTMENTS Controller Position You can move the controller in toward or out away from the armrest or change the position of the control ler for either left hand or right hand use WARNING Do not place the controller harness so that it can be pinched the seat frame or the power base A frame To extend the controller 1 Flip up the armrest so it is perpendicular to the floor 2 Loosen the setscrew on the controller bracket See figure 10 3 Slide the controller into or out of the armrest to the desired position 4 Tighten the setscrew to secure the controller To change the controller position 1 Turn off power to the controller 2 Unplug the controller harness from the power base 3 Cut the wire tie s that secure the controller harness to the armrest and seat Flip up the armrest so it is perpendicular to the floor Loosen the setscrew on the controller bracket Slide the controller out of the armrest Loosen the setscrew in the other armrest Place the controller in the other armrest Tighten the setscrew to secure the controller 0 Route the controller harness along the seat frame and secure with wire ties See figure 7 11 Plug the controller connector into the power base See figure 2 gt ce seo Soy Foot Platform Angle Adjustment You can adjust the angle
34. ws the power available and extends the time needed to recharge the battery just as with a car battery It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature More importantly it will take a few charging cycles a partial drain then a full recharge to establish the critical chemical balance that is essential to the battery s peak performance and long life It will be well worth it to take the time to break in your battery properly Jazzy Sport 2 www pridemobility com 19 VI BATTERIES AND CHARGING How can I ensure maximum battery life A fully charged deep cycle battery will provide reliable performance and extended battery life Keep your power chair s batteries fully charged whenever possible Batteries that are regularly and deeply discharged infrequently charged or stored without a full charge may be permanently damaged causing unreliable power chair operation and limited battery life NOTE The useful life of a battery is quite often a reflection of the care it receives How should I store my power chair and its batteries If you do not use your power chair regularly we recommend maintaining battery vitality by charging the batteries at least once per week If you do not plan on using your power chair for an extended period fully charge the batteries prior to storage Disconnect the battery harnesses and store the power chair in a warm dry environment
35. y Sport 2 IV ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation NOTE Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nylon insert lock nut Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert resulting in a less secure fit Replacement nylon insert lock nuts are available at local hardware stores or by contacting your authorized Pride Provider Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair WARNING Do not pick up the seat frame by the armrests They 7 free to pivot and may lose control of the seat if they do so To install the seat 1 Adjust the upper seat post to the desired position and insert the bolt through the seat post and secure with the nut See figure 6 2 Slide the seat down onto the upper seat post CONTROLLER See figure 6 3 Install the controller into one of the armrests Tighten the setscrew with the supplied hex key See figure 6 4 Lift the armrest straight up then route the controller harness and secure with wire ties as shown in figures 6 and 7 SETSCREW UPPER SEAT NOTE It is important that the armrest be lifted straight up prior to securing the controller harness with wire ties MANDATORY Preve
36. y prior to your trip Plan your trip in advance to avoid inclines if possible Limit baggage weight to essential items Try to maintain an even speed and avoid stop and go driving Pride recommends charging your batteries for at least 48 continuous hours once per month to improve battery performance and battery life What type of batteries should I use We recommend deep cycle batteries that are sealed and maintenance free Both AGM and Gel Cell are deep cycle batteries that are similar in performance WARNING Corrosive chemicals contained in batteries Use only AGM or Gel Cell batteries to reduce the risk of leakage or explosive conditions Why do my new batteries seem weak Deep cycle batteries employ a much different chemical technology than that used in car batteries nickel cadmium nicads or in other common battery types Deep cycle batteries are specifically designed to provide power drain down their charge and then accept a relatively quick recharge AGM and Gel Cell batteries should be charged as often as possible They do not have a memory like nickel cadmium batteries We work closely with our battery manufacturer to provide a battery that best suits your power chair s specific demands Fresh batteries arrive regularly and are promptly shipped with a full charge During shipping the bat teries encounter temperature extremes that may influence initial performance Heat robs the charge from the bat tery and cold slo
37. your power chair Check for proper tire inflation Maintain but do not exceed psi bar kPa air pressure rating indicated on each tire if equipped with pneumatic tires Check all electrical connections Make sure they are tight and not corroded Check all controller connections to the power base Make sure they are secured properly Check the brakes See VII Care and Maintenance Check battery charge See VI Batteries and Charging Ensure the manual freewheel levers are in drive mode before sitting on the power chair NOTE If you discover a problem contact your authorized Pride Provider for assistance 6 www pridemobility com Jazzy Sport 2 lll YOUR POWER CHAIR THE JAZZY SPORT 2 POWER CHAIR The Jazzy Sport 2 Power Chair has two main assemblies the seat assembly and the power base assembly See figure 1 Typically the seat assembly includes the armrests seatback and seat base The power base assembly includes two motor brake assemblies two drive wheels two rear caster wheels two front anti tip wheels two batteries and wiring harnesses SEATBACK ARMRESTS SEAT ASSEMBLY SEAT BASE CONTROLLER BODY SHROUD W CASTER WHEEL RANAR YN 2 FRONT RIGGING DRIVE WHEEL FOOT PLATFORM SHOWN ANTI TIP WHEELS Figure 1 The Jazzy Sport 2 Power Chair Jazzy Sport 2 www pridemobility com 7 lll YOUR POWER CHAIR SEAT POST MAIN CIRCUIT BREAKER MAIN SHROUD FRONT CO
Download Pdf Manuals
Related Search