Extron VoiceLift Microphone System with PVS
Contents
1. 3Extron Electronics INTERFACING SWITCHING AND CONTROL This guide provides instructions for an experienced installer to set up install and connect the Extron VLP 202 VoiceLift Compact Pendant Microphone or VLH 102 VoiceLift Handheld Microphone the VLC 202 Charging Station and the VLR 102 Receiver in a system with a PVS 405D PoleVault Digital Switcher Setting Up the VLP 202 and VLH 102 Microphones P p P Installing the VLC 202 Charging Station To install the VLC 202 Charging Station 1 2 Power Indicator LED VLP 202 Pendant Microphone VLH 102 Handheld Microphone Set the channel using the rotary switch A and C 2 3 MHz B and D 2 8 MHz For the VLH 102 remove the battery cover to access this switch For pendant microphones only apply the appropriate sticker provided to identify the microphone Remove the battery cover and insert a AA battery If necessary replace the battery cover and 4 charge the rechargeable battery see Installing the VLC 202 Charging Station below Clip For pendant microphones only attach the lanyard lock to the lanyard then press the top of the i microphone clip to raise it Slide the lanyard lock under the clip and release the clip See the illustration at right Place the lanyard around y2. All rights reserved All trademarks mentioned are the property of their respective owners LAN 1 LAN 2 LAN 3 Extron India 1800 3070 3777 Inside India Only Extron Korea 82 2 3444 1571 82 2 3444 1575 FAX 91 80 3055 3777 91 80 3055 3737 FAX www extron com 68 2548 50 Rev A 02 14
3. ameter If necessary separate the receiver housing from the base see the VoiceLift Microphone System User Guide available at www extron com Align the center of the receiver housing with the hole in the ceiling tile Insert the mounting screw through the receiver housing and the hole in the ceiling tile Attach the provided Z bracket to the end of the screw on the back side of the ceiling tile Replace the ceiling tile Pull a shielded CAT5 cable to the receiver location and connect one end of the cable to the RJ 45 jack labeled OUT on the receiver base Align the arrow on the dome tab with the raised arrow on the edge of the housing Rotate the dome clockwise until the arrow on the tab aligns with the raised dot on the housing Connect the other end of the shielded CAT5 cable to the PoleVault switcher INPUTS Ry PVs 405D OUTPUT AUDIO OUT PAGIN L a lense oe VOICELIFT A L R coe ABARA AMPLIFIED AUDIO OUT INPUT 5 UX C a C_ AARAA AEB uy y y Out y VLR 102 PoleVault Switcher Extron Middle East 971 4 299 1800 971 4 299 1880 FAX Extron China 86 21 3760 1568 86 21 3760 1566 FAX Extron Asia 65 6383 4400 65 6383 4664 FAX Extron Europe 800 3987 6673 Inside Europe Only Extron Japan 81 3 3511 7655 81 3 3511 7656 FAX Extron USA East 1 919 850 1000 1 919 850 1001 FAX 31 33 453 4040 31 33 453 4050 FAX 2014 Extron Electronics
4. our neck and slide the lanyard through the lock until the microphone is positioned approximately 4 inches 10 2 cm below your chin 4 1M Turn the microphone on by sliding the power switch up Speak in a normal tone of voice Do not block the microphone port or grille opening Lock Adjust the volume if necessary Ensure that a direct line of sight exists from the microphone to the receiver required for proper operation Do not block the microphone IR transmitter window Pwr LED Plug the wall charger 5 V 1 A into a wall outlet Connect the wall charger cable to the charging station power jack Place the microphone in one of the slots in the charger The charge is complete when the microphone LED turns green this can take up to 5 hours NOTE The microphone can be left to charge for extended periods It should be turned off while charging CAUTION Risk of explosion Do not replace the battery with an incorrect type ATTENTION e Do not charge alkaline batteries Installing the VLR 102 Receiver To install the VLR 102 IR Receiver in a drop ceiling 1 2 Extron Headquarters 800 633 9876 Inside USA Canada Only Extron USA West 1 714 491 1500 1 714 491 1517 FAX e Dispose of used batteries according to the instructions provided on the battery packaging In the ceiling tile cut a hole 2 to 3 inches 50 to 76 mm in di
Download Pdf Manuals
Related Search