Home

BlackDiamond X8 Series Switches Hardware

1. Figure 4 BDXA 10G48X I O Module 1 10 Gigabit Ethernet ports 2 LEDs In the default configuration for the BDXA 10G48X module all ports e Are added to the default VLAN as untagged e Inherit the properties of the default VLAN for example protocol type and VLAN ID The BDXA 10G48X module has the following LEDs e Module status STAT e Module diagnostics DIAG e Port status For information about the LEDs and their activity on the BDXA 10G48X modules see O Module L on page 20 BlackDiamond X8 Series Switches Hardware Installation Manual EDs BlackDiamond X8 Series Modules and Fans BDXA 40G24xX I O Module The BDXA 40G24X I O module supports 24 QSFP based 40 gigabit Ethernet ports Each QSFP port can operate as a single 40 gigabit port or as four 10 gigabit ports In 40G port mode the module provides 24 ports if all ports are operating in 10G mode the module provides 96 ports Note e BlackDiamond X8 I O modules are supplied with no pre installed optical modules When the ports are operating in 40 Gbps mode the port numbers increment by 4 For example the first four ports in the top row would be numbered from left to right 1 5 9 and 13 Other port numbers are displayed in ExtremeXOS as not available When a port is configured to operate in 10 Gbps mode all four port numbers associated with that physical port are displayed as being available
2. BlackDiamond X8 Series Switches Hardware Installation Manual 25 Understanding Power Supplies AC Power Supply The AC power supply for the BlackDiamond X8 delivers 2500 W when operated from 185 to 264 VAC or 1250 W when operated from 90 to 140 VAC Figure 10 BlackDiamond X8 AC Power supply 1 LEDs 3 Inserter extractor lever 2 Release button Each AC PSU contains two cooling fans at the front of the unit Airflow is from front to back The BlackDiamond X8 AC power supply does not contain a field operator replaceable fuse Warning A N Field operators must not attempt to configure or replace fuses in Extreme Networks AC power supplies In the event of failure immediately return the defective Extreme Networks AC power supply for a complete replacement For information about installing the BlackDiamond X8 AC PSU see Installing Power Supplies on page 49 For more information on PSU redundancy see Understanding PSU Redundancy in the BlackDiamond X8 Chassis on page 24 Reading AC Power Supply LEDs The BlackDiamond X8 AC power supply has status LEDs on the front panel The following table describes the meanings of the power supply LEDs BlackDiamond X8 Series Switches Hardware Installation Manual 26 Understanding Power Supplies Table 8 LEDs on the BlackDiamond X8 AC Power Supply LED Type and Color Power Supply Condition AC O
3. 2 Management port and USB ports 4 Auxiliary port with LED Reading Management Module LEDs LEDs on the management module provide status information about operation of the switch and major chassis components Table 4 LEDs on the BDX MM1 Management Module Label Function Color State Meaning ERR Amber steady A critical software error has been logged since power up eee Off Normal operation is occurring NV Green steady The system is operating within the defined operational limits nvironmental status 5 5 RE Amber steady The system is operating outside the defined operational limits STR Green steady This management module is the master in the system aster backup status ET of mod le Green blinking Power on self test POST is running Amber steady Module is operating as backup secondary MM Off Normal operation for diagnostics BlackDiamond X8 Series Switches Hardware Installation Manual 15 BlackDiamond X8 Series Modules and Fans Table 4 LEDs on the BDX MM1 Management Module continued Label Function Color State Meaning SYS Green blinking The system has booted and is operating normally System status Tass 3 R 3 Y Amber blinking Diagnostic tests are running on the module The LED resets if the diagnostics are terminated The LED returns to flashing amber if another diagnostic test is started
4. BDXA 10G48T 48 Port IOGBASE T RJ45 908016 10 module for BlackDiamond X series chassis Up to eight modules in the BlackDiamond X8 chassis support up to 384 wirespeed IOGbE copper ports and work with either 2 56 or 5 12Tbps Fabric Modules Understanding Management Modules The switch has two dedicated management module slots labeled A and B for the BDX MMI management module One management module is required for switch operation however adding a second management module increases system reliablility through redundancy Each management module contains a temperature sensor nonvolatile random access memory NVRAM and a real time clock BlackDiamond X8 Series Switches Hardware Installation Manual 13 BlackDiamond X8 Series Modules and Fans The management module has very high speed and scalable control plane support with an Intel i7 dual core CPU which will run at 2 GHz 1GB compact flash and 2 GB ECC DDR3 SDRAM The following sections describe the functions and features of the BlackDiamond X8 management modules e Understanding Redundant Management Module Activity on page 14 e Features of the Management Module on page 14 e Reading Management Module LEDs on page 15 Understanding Redundant Management Module Activity The switch can operate with a single management module installed or with two management modules installed for redundancy When you install a second management module one of t
5. 1550 nm optical window 1 Proprietary to Extreme Networks Connections between two Extreme Networks 1000BASE LX interfaces that use 10 125 um single mode fiber can use a maximum distance of 10 km BlackDiamond X8 Series Switches Hardware Installation Manual 34 Preparing Your Site Table 10 Fiber Media Types and Maximum Cable Distances continued Standard Media Type Mhz Km Maximum Distance Rating 1000BASE BX10 10 125 um single mode fiber 10 km 1490 nm optical window 1310 nm optical window 1000BASE LX70 10 125 um single mode fiber 70 km 1550 nm optical window 10GBASE SR SFP 62 5 mm multimode fiber 160 26 meters 850 tical wind SIDE 62 5 mm multimode fiber OM1 200 33 meters 50 mm multimode fiber 400 66 meters 50 mm multimode fiber OM2 500 82 meters 50 mm multimode fiber OM3 2000 300 meters 10GBASE LR SFP 10 125 um single mode fiber 10 km 1310 nm optical window 10GBASE ER SFP 10 125 um single mode fiber 40 km 1550 nm optical window AOGBASE LR4 QSFP 1310 nm singlemode fibre 10 km optical window A4OGBASE SR4 QSFP 50 mm multimode fiber OM3 100 meters 850 tical wind niy Optical WINdow 50 mm multimode fiber 0M4 150 meters Table 11 Copper Cable Category Transmission Rate and Maximum Cable Distances Cable Category Distance for 100 Mb s Distance for 1Gb
6. Caution Be careful to avoid over torquing and stripping the screw heads RRRR KRK RH III ptatatet SINN Figure 40 Locking the I O module blank into place Installing I O Module Blanks without thumb levers Some of the older BDX chassis were shipped with module blanks without thumb levers Use the following procedure if you have these older module blanks If you have the newer module blanks with thumb levers see Installing I O Module Blanks on page 62 You need a 2 Phillips screwdriver to install a module blank without thumb levers After you have installed all the I O modules for your system configuration you must install module blanks in all remaining unoccupied slots Caution All unoccupied slots in a BlackDiamond X8 series switch must have module blanks correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch 1 Check the condition of the EMI gaskets along the front panel edges of the blank and confirm that the gaskets are not damaged BlackDiamond X8 Series Switches Hardware Installation Manual 64 Installing BlackDiamond X8 Series Modules 2 Align the module blank with the card guides for the open slot on the chassis Figure 41 Installing a Module Blank without thumb levers 3 Usea 2 Phillips screwdriver to tighten the captive screws at each end of the module blank Tighten the screws of eac
7. 0 2 g O to peak 0 1 oct min Operational random vibration 3 to 500 Hz 1 5g rms ASTM D3580 random vibration unpackaged 1 5g NOTE Operating temperature refers to the input air temperature in the environment and applies to all switch components The show temperature CLI command displays the internal temperature of individual hardware components as well as the allowable internal temperature range for each component Storage amp transportation Transportation temperature 40 C to 70 C 40 F to 158 F conditions packaged Storage and transportation humidity 10 to 93 relative humidity non condensing Packaged shock half sine lt 50 kg 180 m s 10 g 6 ms 600 shocks modules gt 50 kg 100 m s 6 g 11 ms 600 shocks chassis Packaged random vibration 5 to 20 Hz 1 0 ASD w 3 dB oct from 20 to 200 Hz 14 drops minimum on sides amp corners 39 5 lt 22 Ib 10 kg modules 11 8 lt 110 Ib 50 kg chassis Table 19 Acoustic Sound Sound pressure for comparison to Low Speed 60 3 dB A per ISO 7779 2010 legacy standards edium Speed 66 0 dB A per ISO 7779 2010 High Speed 82 3 dB A per ISO 7779 2010 Sound power in accordance with Low Speed 72 0 dB A per ISO 3744 1994 EN 300 753 v1 3 1 2011 11 Medium Speed 78 0 dB A per ISO 3744 1994 igh Speed 94 4 dB A per ISO 3744 2010 Declared sound power in Low Speed 7 5 B A in accordance with ISO 9296 1998 accordance with
8. 6 Slide the module out of the chassis slot 7 Immediately place the module into an anti static bag to protect it from potential ESD damage The bag will also prevent dust from collecting on the module connectors 8 If you are not going to install a replacement module install a blank front panel See Installing I O Module Blanks on page 62 Installing an I O Module You need the following tools and equipment to install an I O module e ESD preventive wrist strap e 2 Phillips screwdriver e Module blank panel if you are not replacing the module BlackDiamond X8 Series Switches Hardware Installation Manual 83 Maintaining the BlackDiamond X8 Slots for I O modules are numbered 1 through 8 starting at the top Note All unoccupied I O module slots must be covered by I O module blanks to ensure proper system ventilation and EMI compliance Individual O module blanks are purchased separately from the chassis See Installing I O Module Blanks on page 86 to install I O blanks 1 Remove the shipping cover from the I O module slots The shipping cover maintains the mechanical stability of the chassis during shipping 2 Keep the shipping cover and store it with the other chassis shipping materials in case you need to move the chassis or return it to Extreme Networks 3 Attach the ESD preventive wrist strap to your bare wrist If it is not already connected connect the metal end to the receptacle between the management
9. s local electrical codes BlackDiamond X8 Series Switches Hardware Installation Manual 101 Safety Information Battery Replacement and Disposal Batteries included with Extreme products are encapsulated and must be replaced only by qualified Extreme Service personnel 1 Contact your Extreme Networks Service personnel for product replacement 2 Donot attempt to replace the battery Caution LN If these instructions are disregarded and replacement of these batteries is attempted the following guidelines must be followed to avoid danger of explosion a Replace with the same or equivalent battery type as recommended by the battery manufacturer b Dispose of the battery in accordance with the battery manufacturer s recommendation Fiber Optic Ports and Optical Safety The following safety warnings apply to all optical devices used in Extreme Networks equipment that are removable or directly installed in an I O module or chassis system BlackDiamond X8 Series Switches Hardware Installation Manual 102 Safety Information Such devices include but are not limited to gigabit interface converters GBICs small form factor pluggable SFP modules or mini GBICs QSFP modules XENPAK transceivers and XFP laser optic modules A Caution Laser optic modules become very hot after prolonged use Take care when removing a laser optic module from the module or option card If the laser optic module is to
10. 8 If you are not going to install a replacement module install a blank front panel For more information see Installing a Management Module Blank on page 60 Installing a Management Module Replace an old management module with a new one BlackDiamond X8 Series Switches Hardware Installation Manual 80 Maintaining the BlackDiamond X8 1 Holding the module by the metal rail and front panel only remove the module from the antistatic packaging Caution 2 To prevent ESD damage never touch the components on the PCB or the pins on any of the connectors 2 Verify that the injector ejector handle is in the open position Keep the injector ejector handle in the open position as you slide the module into the chassis slot 3 Carefully slide the module into the slot until the injector ejector handle engages the edge of the chassis and begins to rotate toward the module 4 Use the lever to fully seat the internal module connectors Figure 56 Installing a Management Module BlackDiamond X8 Series Switches Hardware Installation Manual 81 Maintaining the BlackDiamond X8 5 Use a 2 Phillips screwdriver to lock the handle into place When the locking screw is fully tightened the yellow band around the screw head is completely hidden Caution Be careful to avoid over torquing and stripping the screw head KARA KART aaa HRH LASMANIS Fig
11. PC AT null modem serial cable Switch PC AT Serial Port Cable connector 9 pin female Cable connector 9 pin female Screen Shell 6 Shell Screen DTR 4 1 DCD TxD 3 2 RxD RxD 2 3 TxD CTS 8 4 DTR Ground 5 5 Ground DSR 6 6 DSR RTS 7 7 RTS DCD 1 8 CTS Figure 79 PC AT Serial Null modem Cable Pinouts Conformity Statements for EMC Class A International CISPR 22 Class A This is a Class A product Ina domestic environment this product may cause radio interference in which case the user may be required to take adequate remedial measures FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications BlackDiamond X8 Series Switches Hardware Installation Manual 117 Technical Specifications Operation of this equipment in a residential area is likely to cause harmful interference in which case you are required to correct the interference at your own expense Canada Class A This Class A digital apparatus complies
12. Words in italicized type Italics emphasize a point of information or denote new terms at the place where they are defined in the text Book titles are printed in italics Related Publications The documentation set for Extreme Networks ExtremeXOS switches and routers includes e ExtremeXOS Concepts Guide e ExtremexOS Command Reference Guide e ExtremexOS Release Notes BlackDiamond 20800 Series Switches Hardware Installation Guide legacy product e BlackDiamond 10808 Switch Hardware Installation Guide legacy product e BlackDiamond 12800 Series Switches Hardware Installation Guide legacy product e BlackDiamond 8800 Series Switches Hardware Installation Guide e BlackDiamond X8 Series Switches Hardware Installation Guide this guide Summit Family Switches Hardware Installation Guide e Extreme Networks E4G Series Routers Hardware Installation Guide e Extreme Networks Pluggable Interface Modules Installation Guide e ExtremexXOS Hardware and Software Compatibility Matrix Hardware and software documentation for Extreme Networks products is available from the Extreme Networks website You can download software concepts guides and reference guides hardware installation guides and other documents at www extremenetworks com go documentation BlackDiamond X8 Series Switches Hardware Installation Manual Under your product warranty or with a current support contract you can access software relea
13. 2 Phillips screwdriver for attaching the mid mount brackets to the middle of the chassis sides Rack mount screws appropriate for your organization s rack system as follows e Ascrews to attach each support bracket to the rack e 12 screws to secure the chassis in the rack The screw size will vary based on your organization s rack system screws are not provided Screwdriver appropriate for the selected rack mounting screws Chassis grounding materials as listed in Grounding the Chassis on page 48 Rack Mounting the Chassis Note The chassis provides three possible locations on each side for the mid mount brackets labeled A B and C When you attach the brackets make sure you use the same position on each side Figure 20 Locating Possible Mid mount Bracket Points Before you install the chassis verify that none of the modules or power supplies have been pre installed Because of the weight of the chassis it should be empty when you install it 1 Attach mid mount brackets to the sides of the chassis a On each side of the chassis align a mid mount brackets with its mounting holes on the chassis sheet metal BlackDiamond X8 Series Switches Hardware Installation Manual 45 Installing a BlackDiamond X8 Series Chassis b Using a 2 Phillips screwdriver insert and tighten the mounting screws to secure the bracket to the chassis Figure 21 Attaching Mid mount
14. EN 300 753 v1 3 1 Medium Speed 8 1 B A in accordance with ISO 9296 1998 2011 11 igh Speed 9 7 B A in accordance with ISO 9296 1998 Modules for BlackDiamond X8 Switches The following table contains the technical specifications for BlackDiamond X8 Series Modules BlackDiamond X8 Series Switches Hardware Installation Manual 113 Technical Specifications Table 20 I O Modules Module Specifications Note Inserter extractor levers add 2 25 inches 5 7 cm to the depth measurement BDXA 10G48X Length 18 inches by width 17 inches by height 2 3 inches 45 5 cm x 41 8 cm x 5 82 cm Weight 10 9 Ib 4 9 kg Packaged weight 16 2 Ib 7 3 kg Power 290 W Heat Dissipation 990 BTU BDXA 40G24X Length 18 inches by width 17 inches by height 2 3 inches 45 5 cm x 41 8 cm x 5 82 cm Weight 14 0 Ib 6 3 kg Packaged weight 19 4 Ib 8 8 kg Power 510 W Heat Dissipation 1740 BTU BDXA 40G12X Length 18 inches by width 17 inches by height 2 3 inches 45 5 cm x 41 8 cm x 5 82 cm Weight 11 0 Ib 5 0 kg Packaged weight 16 4 Ib 7 4 kg Power 265 W Heat Dissipation 904 BTU BDXA 10G48T Length 18 inches by width 17 inches by height 2 3 inches 45 5 cm x 41 8 cm x 5 82 cm Weight 11 1 Ib 5 1 kg Packaged weight 16 1 lb 7 3 kg Power 435 W Heat Dissipation 1 484 BTU Module blank Length 18 inches by width 17 inches by height 2 3 inches 45 0 cm x 41 8 cm x 5 82 cm
15. Figure 45 Installing the Power Supply Ventilation Cover Replacing a Fan Tray You need a 2 Phillips screwdriver to replace a fan tray You can replace a fan tray without powering down the switch 1 Completely loosen the retaining screws at the top and bottom of the fan tray BlackDiamond X8 Series Switches Hardware Installation Manual 71 Maintaining the BlackDiamond X8 2 Holding both handles pull straight outward on the fan tray to disconnect the internal connector 6 Figure 46 Removing a Fan Tray 3 Setthefantray aside in a safe place 4 Holding the replacement fan tray with both handles align it with the opening and slide it straight into the chassis Caution rN If a fan tray is to be replaced while the BlackDiamond X8 is operating the new fan tray should be ready to insert Insert the replacement within five minutes to insure the BlackDiamond X8 does not overheat BlackDiamond X8 Series Switches Hardware Installation Manual 72 Maintaining the BlackDiamond X8 5 Align and tighten the retaining screws s Qe Figure 47 Installing a Fan Tray Replacing a Fabric Module You need a the following tools to replace a fabric module e ESD preventive wrist strap e 2 Phillips cross head screwdriver for the retaining screws on the fan tray 5 16 inch flat tip screwdriver for the
16. Series Switches Hardware Installation Manual 20 BlackDiamond X8 Series Modules and Fans Table 5 LEDs on the BlackDiamond X8 Series I O Modules Type Label Function Color State Meaning Module STAT Green blinking Normal operation Elsa Amber blinking Configuration error code version error diagnostic failure or other severe module error Off The module is not receiving power DIAG Amber blinking Diagnostic tests are in progress Moeuleralashest Amber steady A diagnostic failure has occurred Off ormal operation Port Port status Green steady Link is up Green blinking Port is disabled Amber blinking Packet activity on port Off Link is down Understanding Fabric Modules Up to four fabric modules can be installed in each BlackDiamond X8 chassis to provide the active switching fabric for the switch The switch fabric supports N 1 redundancy Three fabric modules are required to provide full switch fabric capacity The fourth module provides excess capacity for redundancy but is not required to maintain full line rate on the front panel ports Fabric modules are installed in dedicated slots at the back of the chassis behind the fan trays Figure 8 Fabric Module 1 Inserter extractor lever Two types of fabric modules are available for the switch e BDXA FMIOT module e BDXA FM20T module BDXA FMIOT fabric modules provide a total switch fabric capacit
17. The default mode for the ports is 40 Gbps operation When a port is configured to operate in 10 Gbps mode all four port numbers associated with that physical port are displayed as being available To configure a port for 10 Gbps operation use the following command configure ports partition Figure 5 BDXA 40G24X I O Module on page 18shows the front of the module including port and LED locations Figure 5 BDXA 40G624X I O Module 1 QSFP ports 2 LEDs In the default configuration for the BDXA 40G24X module all ports e Are added to the default VLAN as untagged e Inherit the properties of the default VLAN for example protocol type and VLAN ID The BDXA 40G24X module has the following LEDs e Module status STAT e Module diagnostics DIAG e Port status When a port is operating in 40 Gbps mode the farthest left LED below that port lights blue to indicate the 40 Gbps operation When a port is operating in 10 Gbps mode each LED for an active channel from the port lights green BlackDiamond X8 Series Switches Hardware Installation Manual 18 BlackDiamond X8 Series Modules and Fans For information about the LEDs and their activity on the BDXA 40G24X modules see I O Module LEDs on page 20 Note Zz The BDXA 40G24X module requires BDX FM2OT fabric modules in order to function The m
18. Understanding Fan Trays At the back of the BlackDiamond X8 chassis are five vertical fan trays each holding six fans Fan trays are hot swappable Two pairs of L EDs on each fan tray indicate operating status for the fabric module installed behind that fan tray Only the first four fan trays starting from the left most side when looking at the rear of the chassis are associated with fabric modules Caution Never lift the chassis by using the handles on the fan trays BlackDiamond X8 Series Switches Hardware Installation Manual 22 BlackDiamond X8 Series Modules and Fans IS iamond X8 Chassi the BlackD n Fan Trays i Figure 9 LEDs for the Fan Trays Table 7 One or more fans are not operating properly Controller is not functioning properly Firmware upgrade is in progress gt Oo E fe Z D Z O 5 Q D SIEIS 8 oa wo 5 5 ca fol E 2 o O in Z zZ D D S gt j E zZ KEES ec ic 5 Bis 25 v Q N gt yl Ss DSlclo o o olol 2 aja o 2 le zlEe E E OJOJOO c fe 2 O 5 a D WR 2 o amp 23 BlackDiamond X8 Series Switches Hardware Installation Manual 3 Understanding Power Supplies Understanding PSU Redundancy in the BlackDiamond X8 Chassis AC Power Supply The BlackDiamon
19. X series chassis two modules required for 1 1 redundancy Switch fabric module BDXA FM2OT 5 12Tbps Fabric Module for 900849 10 BlackDiamond X chassis Minimum three modules required for wirespeed performance four required for N 1 redundancy supporting full 20Tbps BDXA FMIOT 2 56Tbps Fabric Module for 900850 10 BlackDiamond X chassis Minimum three modules required for wirespeed performance four required for N 1 redundancy supporting full 1OTbps BlackDiamond X8 Series Modules and Fans Table 3 Modules Available for the BlackDiamond X8 Series Switch continued Module Type Short Description Long Description Manufacturing No SKU I O module BDXA 10G48X 48 Port IOGBASE X SFP 900851 10 module for BlackDiamond X series chassis Up to eight modules in the BlackDiamond X8 chassis support up to 384 wirespeed 1OGbE ports and work with either 2 56 or 5 12Tbps Fabric Modules BDXA 40G24X 24 Port ADGBASE X QSFP 900855 10 module for BlackDiamond X series chassis Up to eight modules in the BlackDiamond X8 chassis support up to 192 wirespeed 40GbE or 768 wirespeed IOGbE ports and only work with 5 12Tbps Fabric Module BDXA 40G12X 12 Port AOGBASE X QSFP 900856 10 module for BlackDiamond X series chassis Up to eight modules in the BlackDiamond X8 chassis support up to 96 wirespeed 40GbE or 384 wirespeed 10GbE ports and work with either 2 56 or 5 12Tbps Fabric Modules
20. X8 Series Modules and Fans 12 Module Overview 12 Understanding Management Modules 13 Understanding I O Modules 16 Understanding Fabric Modules 21 Understanding Fan Trays 22 Chapter 3 Understanding Power Supplies 24 Understanding PSU Redundancy in the BlackDiamond X8 Chassis 24 AC Power Supply 26 Chapter 4 Preparing Your Site 28 Planning Your Site 28 Meeting Site Requirements 28 Evaluating and Meeting Cable Requirements 33 Meeting Power Requirements 37 Following Applicable Industry Standards 40 Chapter 5 Installing a BlackDiamond X8 Series Chassis 41 Unpacking the Chassis 41 Checking Pre Installation Requirements 45 Rack Mounting the Chassis 45 Grounding the Chassis 48 Installing Power Supplies 49 Connecting Power Cords 52 Chapter 6 Installing BlackDiamond X8 Series Modules 54 Initial System Installation and Module Installation Order 54 Required Tools 54 Installing Fabric Modules 55 Installing Management Modules 58 Installing I O Modules 60 Applying Power and Accessing the Chassis for the First Time 65 Chapter 7 Maintaining the BlackDiamond X8 68 Replacing a Power Supply 68 Replacing a Fan Tray 71 Replacing a Fabric Module 73 Replacing a Management Module 79 Reseating a Management Module DIMM 89 Packing the Chassis for Shipping 92 BlackDiamond X8 Series Switches Hardware Installation Manual Table of Contents Chapter 8 Safety Information 98 Consideratio Maintenance General Safe S
21. depending on line voltage and round the result up to the next whole integer this number is N 3 Add1toN to get the total number of PSUs required for N Redundancy If more modules are added to the chassis more PSUs may be needed to maintain N 1 Redundancy N 1 Redundancy is possible with any existing chassis configuration even if the line voltage is 120VAC N N Redundancy N N refers to power source redundancy For instance a data center may have two independent power sources available so that if one source fails the other source backup will automatically take over and power the BlackDiamond X8 chassis To achieve N N redundancy the top row of PSUs Bank A should be powered from the same facility power source that is plugged into power circuits derived from a single power source The bottom row of PSUs Bank B should be powered from the backup power source The user needs to install enough PSUs in each bank to power the entire BlackDiamond X8 chassis If the line voltage is 220VAC then there should be no problem powering the entire chassis with four PSUs If the line voltage is 120VAC most configurations can be powered by four PSUs Simultaneous N and N N Redundancy To achieve both N 1 and N N redundancy at the same time three or fewer PSUs must be capable of powering the entire BlackDiamond X8 chassis Each bank of PSUs should be populated with enough PSUs to power the chassis N plus one more chassis N 1
22. designed to support weight Maintenance Safety When you perform maintenance procedures on Extreme Networks equipment follow these recommendations Use only authorized accessories or components approved for use with this system Failure to follow these instructions may damage the equipment or violate required safety and EMC regulations This system contains no customer serviceable components Do not attempt to repair a chassis power supply module or other component In the event of failure return the defective unit to Extreme Networks for repair or replacement unless otherwise instructed by an Extreme Networks representative To remove power from the system you must unplug all power cords from wall outlets The power cord is the disconnect device to the main power source Disconnect all power cords before working near power supplies unless otherwise instructed by a product specific maintenance procedure When you handle modules optic devices power supplies or other modular accessories put on an ESD preventive wrist strap to reduce the risk of ESD induced damage to the equipment Connect the other end of the strap to an appropriate grounding point on the equipment rack or to an ESD connector on the chassis if one is provided You may leave the ESD preventive wrist strap permanently attached so that it is always available when you need to handle ESD sensitive components Install all cables in a manner that avoids strain Us
23. e Module status STAT e Module diagnostics DIAG e Port status BlackDiamond X8 Series Switches Hardware Installation Manual 19 BlackDiamond X8 Series Modules and Fans When a port is operating in 40 Gbps mode the farthest left LED below that port lights blue to indicate the 40 Gbps operation When a port is operating in 10 Gbps mode each LED for an active channel from the port lights green For information about the LEDs and their activity on the BDXA 40G12X modules see O Module LEDs on page 20 BDXA 10G48T I O Module The BDXA 10G48T I O module has 48 copper 10 gigabit Ethernet ports FHH EAE ee See See eee eee eee Figure 7 BDXA 10G48T I O Module 1 10 gigabit Ethernet ports 2 LEDs In the default configuration for the BDXA 10G48T module all ports e Are added to the default VLAN as untagged e Inherit the properties of the default VLAN for example protocol type and VLAN ID The BDXA 10G48T module has the following LEDs e Module status STAT e Module diagnostics DIAG e Port status For information about the LEDs and their activity on the BDXA 10G48T modules see I O Module LEDs on page 20 I O Module LEDs LEDs on the front panel of the BlackDiamond X8 series I O modules provide information about the operating status of the module and ports BlackDiamond X8
24. on the left You can also use the prev next links at the top and bottom of the page To download the publications in PDF or ePub format click the links below BlackDiamond X8 Installation Manual PDF BlackDiamond X8 Installation Manual ePub Audience This guide is intended for use by network administrators responsible for installing and setting up network equipment This guide assumes a basic working knowledge of e Local area networks LANs e Ethernet concepts e Ethernet switching and bridging concepts e Routing concepts e Simple Network Management Protocol SNMP e Basic equipment installation procedures See the ExtremexXOS Concepts Guide and the ExtremeXOS Command Reference Guide for information about configuring the BlackDiamond X8 series switch Note e If the information in an installation note or release note shipped with your Extreme Networks equipment differs from the information in this guide follow the installation or release note Conventions The following tables list conventions used throughout this guide Table 1 Notice Icons Icon Notice Type Alerts you to e Note Important features or instructions Caution Risk of personal injury system damage or loss of data Warning Risk of severe personal injury Table 2 Text Conventions Convention Description Screen displays This typeface represents information as it appears on the screen or command syntax
25. retaining screws on the fabric module You can replace a fabric module without powering down the switch Caution If a fabric module is to be replaced while the BlackDiamond X8 is operating the new fabric module should be ready to insert Insert the replacement and replace the fan tray within five minutes to insure the BlackDiamond X8 does not overheat 1 Attach the ESD preventive wrist strap to your bare wrist 2 If itis not already connected connect the metal end to the receptacle at the right of the power input connectors 3 Remove the fan tray in front of the faulty fabric module a Loosen the captive retaining screws at the top and bottom of the fan tray BlackDiamond X8 Series Switches Hardware Installation Manual 73 Maintaining the BlackDiamond X8 b Holding both handles pull the fan tray straight out of the chassis Figure 48 Removing a Fan Tray 4 Set the fan tray aside in a safe place 5 Remove the fabric module a Loosen the retaining screw on each inserter extractor lever on the fabric module BlackDiamond X8 Series Switches Hardware Installation Manual 74 Maintaining the BlackDiamond X8 b Simultaneously rotate both levers toward the ends of the module to unseat the internal connectors Figure 49 Unseating a Fabric Module on page 75 Figure 49 Unseating a Fabric Module BlackDiamond X8 Series Switches Hardwar
26. s Distance for 10Gb s 5 00 meters 5 OO meters 00 meters 6 00 meters 00 meters 55 meters 6 unscreened 00 meters 00 meters 55 meters 6 screened 00 meters 00 meters 100 meters 6a 00 meters 00 meters 100 meters 7 00 meters 00 meters 100 meters Table 12 Extreme Networks Direct Attach Cables Cable Type Model Number Length SFP passive copper cable 10304 1 meter 10305 3 meters 10306 5 meters 10307 10 meters BlackDiamond X8 Series Switches Hardware Installation Manual 35 Preparing Your Site Table 12 Extreme Networks Direct Attach Cables continued Cable Type Model Number Length QSFP passive copper cable 031 0 5 meter 0312 1 meter 0313 3 meters QSFP active optical cable 0315 10 meters 0316 20 meters 0318 100 meters QSFP to SFP fan out passive copper cable 0321 3 meters 0322 5 meters Installing Cable When you connect cable to your network equipment 1 Examine cable for cuts bends and nicks 2 Support cable using a cable manager that is mounted above connectors to avoid unnecessary weight on the cable bundles 3 Use cable managers to route cable bundles to the left and right of the network equipment to maximize accessibility to the connectors Bundle cable using hook and loop straps to avoid injuring cables NO VI A mm of the cable to avoid radio frequency RF interference oo 9 Use plenum rated cable when it
27. supply Input ranges Low range 90 to 132 V 47 to 63 Hz 15 4 A High range 185 to 264 V 47 to 63 Hz 14 6 A Power supply input socket IEC 320 C20 Minimum wire size 16 AWG 1 0 mm copper stranded Output DC voltage output range 47 5 to 48 5 V ominal DC output Low range 48 V 50 A maximum each power supplyHigh range 48 V75 25 A maximum each power supply DC output power 2500 W high range for one power supply1250 W high range for one power supply Efficiency 90 typical at full load Operating conditions Operating temperature 10 C to 50 C Storage temperature 40 C to 85 C Operating humidity 10 to 95 relative humidity non condensing Operational shock 30 m s 3 g Power Cord Requirements Power cords for use on BlackDiamond X8 AC power supplies have specific requirements e The power supply cord must be agency certified for country of use and rated at 13 A by in country regulatory authority e The power supply cord must have an IEC 320 C19 straight plug to connect to the IEC320 C20 connector on the power supply e The power cord must have an appropriately rated and approved wall plug applicable to the country of installation For cords up to 6 feet 2 m long the wire size must be a minimum of 16 AWG 1 0 mm Connector Pinouts The following table shows the pinouts for the RJ 45 console port on the BlackDiamond X8 switch BlackDiamond X8 Series S
28. the chassis Figure 76 Placing the Shipping Carton over the Chassis BlackDiamond X8 Series Switches Hardware Installation Manual 96 Maintaining the BlackDiamond X8 4 Secure the carton to the pallet using nylon strapping Figure 77 Shipping Carton with Nylon Straps BlackDiamond X8 Series Switches Hardware Installation Manual 97 8 Safety Information Considerations Before Installing Maintenance Safety General Safety Precautions Cable Routing for LAN Systems Installing Power Supply Units and Connecting Power Selecting Power Supply Cords Battery Replacement and Disposal Fiber Optic Ports and Optical Safety Sicherheitshinweise berlegungen vor der Installation Allgemeine Sicherheitshinweise Sicherheit bei Wartungsarbeiten Kabelverlegung f r LAN Systeme Installation der Netzteile und Netzanschluss Auswahl der Netzkabel Wechseln und Entsorgen der Batterie LWL Ports und optische Sicherheit Only trained and qualified service personnel as defined in IEC 60950 1 should install replace or perform service to Extreme Networks switches and their components o Warning Ay Read all of the following safety information topics and sub topics thoroughly before installing Extreme Networks products Failure to follow this safety information can lead to personal injury or damage to the equipment Qualified personnel have read all related installation manuals have the te
29. the following functions e Automatically shut down equipment during long power outages e Monitor and log power supply status e Display the voltage current draw of the equipment e Restart equipment after a long power outage e Display the voltage currently on the line e Provide alarms on certain error conditions e Provide short circuit protection Selecting a UPS Select a UPS that meets your requirements e What are the amperage requirements e What is the longest potential time period that the UPS would be required to supply backup power e Where will the UPS be installed e What is the maximum transition time that your installation will allow Note 2 We recommend that you use a UPS that provides online protection Calculating Volt Amperage Requirements Building and electrical codes vary depending on your location 1 Multiply the number of PSUs by 2500W to get VA If the BDX is to be operated from TIOVAC then multiply the number of PSUs by 1250W to get VA VA Volts multiplied by Amperes 2 Add 30 to the total recommended by Extreme Networks to determine the minimum volt amperage requirements for your UPS UPS Transition Time Transition time is the time that is necessary for the UPS to transfer from utility power to full load battery power For Extreme Networks products a transition time of less than 20 milliseconds is required for optimum performance BlackDiamond X8 Series Switches Hardwar
30. thumb levers 3 Usea 2 Phillips cross head screwdriver to tighten the captive screws at each end of the module blank Tighten the screws of each installed module blank before inserting additional modules or blanks Reseating a Management Module DIMM If you need to reseat the DIMM perform the following procedure 1 Attach the ESD preventive wrist strap to your bare wrist If it is not already connected connect the metal end to the receptacle between the management module slots 2 Disconnect network cables from the front of the module BlackDiamond X8 Series Switches Hardware Installation Manual 89 Maintaining the BlackDiamond X8 3 On the injector ejector lever turn the captive screw counter clockwise until the yellow band around the screw head of is completely visible Figure 65 Unlocking a Module 4 Squeeze the release latch on the injector ejector handle and rotate the handle to the right away from the module to unseat the module from the internal connectors Caution ESD damage hold the module by the metal rail and front panel only Never To prevent touch the components on the PCB or the pins on any of the connectors except those components listed in this procedure Figure 66 Removing a Management Module 5 Slide the module out of the chassis slot 6 Place the module on an anti static surface BlackDiamond X8 Series Switches Hardware Installati
31. with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada Class A Notice for Taiwan Warning AS This is a Class A product In a residential environment this product may cause radio interference in which case the user may be required to take appropriate measures SAPAA BERN ANEN CERI lt JESERNAFE TERRA ERBBEREXRKRNREBENENR or LEA ABS im gid oak TAP tm AY REER REFA FP A Re RHR FARRA SEH 4T ETE HE o Japan VCCI Class A This is a Class A product based on the standard of the VCCI Council If this equipment is used in a domestic environment radio interference may occur in which case the user may be required to take corrective actions CORB TIZAAPMIRNRE TH ORE t RERA CREAT SERRHERHIEEITZERBNET COMBICMPAAM BIS WREST SLIBRENSCEPGVET VCCI A BlackDiamond X8 Series Switches Hardware Installation Manual 118 Index A AC power cord 27 AC power supply features 26 LEDs 27 access restricted 30 ANSI standards 40 B BDX MMI module see management module BDXA 10G48T I O module features 20 LEDs 20 BDXA 10G48x I O modu features 17 LEDs 20 BDXA 406G12X I O module features 19 LEDs 20 BDXA 40G24x I O module features 18 LEDs 20 BDXA FMIOT module features 21 LEDs 22 BDXA FM2OT module features 21 LEDs 22 bend radius 36 BICSI standards 33 BlackDiamond X8 switch grounding terminals location 32 module blanks 62
32. 16 PC AT serial null modem cable 117 RJ 45 console port 116 plenum rated cable 36 ports console 15 console port settings 66 management 11 14 power cord obtaining 27 requirements 38 power requirements power cord 38 power supplies 37 38 power supply AC 26 power system 24 PSU N and N N redundancy 25 N redundancy 25 N N redundancy 25 overview 25 R rack specifications BlackDiamond X8 Series Switches Hardware Installation Manual 120 Index grounding 32 mechanical 31 mounting hole spacing 31 securing to floor 33 space requirements 32 radio frequency interference 36 redundant management module 14 related publications 6 replacement fabricmodule 73 fantray 71 management module 79 power supply 68 requirements AC power cord 27 airflow 31 grounding 32 space 32 restricted access 30 RF interference patch panel installation 36 preventing 37 S safety information in German 104 safety requirements 98 safety requirements 29 service access to the rack 32 signal quality and RF interference 37 site planning process 28 slack in cable 36 space requirements rack 32 specifications AC power supply 115 BlackDiamond X8 switch 111 chassis 111 standards cabling 33 40 commercial building 40 grounding 40 rack 31 storage conditions 113 support bracket 47 switch configuration saving 14 switch fabric capacity 21 system initialization 54 F technical specifications AC power supply 115 BlackDiamond
33. 40G12X I O module 19 BDXA 40G24X I O module 18 B B ackDiamond X8 chassis 8 ackDiamond X8 switch 8 fabric module 21 management module 13 14 power supplies 24 fiber optic cable bend radius 36 handling 36 installing 36 first switch login 66 fuses in power supplies 26 31 G German safety information 104 grounding racks 32 requirements 40 wiring closet 30 grounding terminals location 32 H humidity 30 1 0 modules installing 60 84 LEDs 20 types 13 industry standards 40 initial switch login 66 initial system installation 54 installation abric modules 55 an tray 71 I O modules 60 84 management modules 58 module blank 62 86 old module blank 64 IP settings configuring 66 L labeling system for cables 33 LEDs AC power supply 27 fan tray 23 I O modules 20 management module 15 switch fabric module 22 logging in to the switch 66 M management module dual management modules 14 features 14 installing 58 LEDs 15 redundant 14 USB port 11 14 management port 11 management port location 14 mechanical recommendations for rack 31 module blank installing 62 86 module configuration default 16 modules I O 16 management 14 switch fabric 21 mounting holes rack 31 32 N null modem cable pinouts 116 O old module blank installing 64 operating conditions 13 operating environment requirements 30 P physical layer problems 37 pinouts null modem cable 1
34. 64 overview 8 specifications 111 building codes 29 Building Industry Consulting Service International see BICSI C cable category 5 36 fiber optic 36 installation recommendations 36 types and distances 34 cabling standards ANSI 40 BICSI 33 capacity switch fabric 21 category 5 cable 36 chassis grounding 48 installing 41 oO mounting 45 unpacking 41 commercial building standards 40 compatibility switch fabric 21 components installing fabric modules 55 I O modules 60 84 management modules 58 module blank 62 86 old module blank 64 power cord retainer 53 components removing chassis 93 fabric module 73 fantray 71 management module 79 89 power supply 68 connector pinouts 116 console port location 15 settings 66 console port pinouts 116 D default module configuration 16 design standards 40 distribution rack 31 E electrostatic discharge see ESD environmental requirements airflow 3 building codes 29 equipment location 30 humidity 30 temperature 30 equipment rack grounding 32 mechanical recommendations 31 mounting holes 32 securing 33 service access 32 space requirements 32 ESD discharge from cable 36 system protection 31 F fabric module features 21 installing 55 LEDs 22 fan trays 22 BlackDiamond X8 Series Switches Hardware Installation Manual 119 Index features BDXA 10G48T I O module 20 BDXA 10G48X I O module 17 BDXA
35. Amber steady Diagnostic failure has occurred Off The switch is not receiving power FAN Amber steady A fan failure has occurred Check the Fan LEDS on the fan trays at General fan status the rear of the chassis See Table 7 LEDs for the Fan Trays on page 23 Off Fans are operating normally FM Amber steady The fabric module is running diagnostics or has a fault condition Fabric module status Check the FM LEDs on the fan trays at the rear of the chassis See Table 6 LEDs for the BlackDiamond X8 Series Fabric Modules on page 22 Off All the fabric modules are operating normally Link Green Link is up on Management port E port Tor Link is down Activity Amber Packet activity is occurring on Management port Au 7 pom Off No packet activity is occurring Auxiliary port N A For future development unlabeled Understanding I O Modules The switch has the following I O modules available e BDXA 10G48X e BDXA 40G24X e BDXA 40G12X e BDXA 10G48T No configuration information is stored on the I O modules all configuration information is stored on the management modules When a switch is powered on the software generates a default configuration for any slots that contain I O modules The default configuration allows the I O module ports to participate in the VLAN named default The default configuration for the I O module is not preserved unless you explicitly save the configuration to NVRAM BlackDiamon
36. BlackDiamond X8 Series Switches Hardware Installation Manual Copyright AccessAdap Ethernet Eve ExtremeWor Ridgeline Se Unified Access RF Manager UniStack XNV the BlackDiamon 2001 2013 Extreme Networks rywhere Extreme t Alpine Altitude BlackDiamond Direct Attach EPICenter s ExtremeXOS Go Purple Extreme Solution ntriant ServiceWatch Summit SummitStack Triumph Unified Access Architecture Extreme Networks logo the Alpine logo the d logo the Extreme Turbodrive logo the Summit logos and the Powered by ExtremeXOS logo are trademarks or registered trademarks of ExtremeWorks Essentials Enabled Extreme Ethernet Everywhere Extreme Networks Extreme Standby Router Protocol Extreme Turbodrive Extreme Velocity ExtremeWare subsidiaries in the United States and or other countries sFlow is the property of iBooks is property of Apple Inc nMon Corporation Specifications are subject to change without notice All other registered trademarks trademarks and service marks are property of their respective owners ExtremeXOS ScreenPlay ReachNxT Extreme Networks Inc or its Table of Contents Preface 5 Audience 5 Conventions 5 Related Publications 6 Chapter 1 BlackDiamond X8 Series Switches 8 BlackDiamond X8 Overview 8 BlackDiamond X8 Chassis Features 8 Management Module Ports Overview 11 Chapter 2 BlackDiamond
37. Brackets position C shown 2 Identify the rack location where the chassis will be installed BlackDiamond X8 Series Switches Hardware Installation Manual 46 Installing a BlackDiamond X8 Series Chassis 3 Using four rack mounting screws attach the support bracket to the equipment rack immediately below the intended chassis location Screws are not provided To provide wider support for the chassis as you install it you can attach the second support brack on the other side of the rack post o0 00 00 8 00 00e o gt ooo ooo ooo 00 f Figure 22 Attaching the Support Bracket If necessary attach the lifting handles to each side of the chassis From the front of the rack lift the back of the empty chassis onto the support bracket If attached remove the lifting handles from both sides of the chassis Slowly guide the chassis into the equipment rack until the mounting brackets are flush against the rack uprights 8 Secure the chassis to the equipment rack using six rack mounting screws NO VI DB Screws are not provided BlackDiamond X8 Series Switches Hardware Installation Manual et 47 Installing a BlackDiamond X8 Series Chassis 9 Check to ensure screws are secure Figure 23 Securing the Chassis to the Rack 10 After the chassis is secured to the equipment rack ground the chassis Grounding the Chassis Although gro
38. Hardware Installation Manual 78 Maintaining the BlackDiamond X8 b Align and tighten the retaining screws ez ES A eel J Figure 53 Installing a Fan Tray Replacing a Management Module You need the following tools and equipment to replace a management module ESD preventive wrist strap 2 Phillips screwdriver Module blank panel if you are not replacing the module Attach the ESD preventive wrist strap to your bare wrist If it is not already connected connect the metal end to the receptacle between the management module slots Disconnect network cables from the front of the module BlackDiamond X8 Series Switches Hardware Installation Manual 79 Maintaining the BlackDiamond X8 4 Onthe injector ejector lever turn the captive screw counter clockwise until the yellow band around the screw head of is completely visible Figure 54 Unlocking a Module 5 Squeeze the release latch on the injector ejector handle and rotate the handle to the right away from the module to unseat the module from the internal connectors Figure 55 Removing a Management Module Slide the module out of the chassis slot 7 Immediately place the module into an anti static bag to protect it from potential ESD damage The bag will also prevent dust from collecting on the module connectors
39. KGreen DCOKGreen ALMRed No AC input power to any power supply Off Off Off Receiving standby output from backplane AC input power is present On Off Off 48 V output is disabled Standby output is ON AC input is present DC outputs are good On On Off AC input is good output 48 V has a fault On Off On Output is good but a warning alarm has been detected for On On On example Undervoltage Understanding Power Supply Cords An AC power cord is not included with the BlackDiamond X8 AC power supply You can purchase AC power cords for use in the US and Canada from Extreme Networks or from your local supplier An AC power cord for use with the BlackDiamond X8 AC power supply must meet the requirements listed in Power Cord Requirements on page 115 BlackDiamond X8 Series Switches Hardware Installation Manual 27 4 Preparing Your Site Planning Your Site Meeting Site Requirements Evaluating and Meeting Cable Requirements Meeting Power Requirements Following Applicable Industry Standards The information in this section is intended for the system administrator network equipment technician network manager or facilities manager responsible for installing and managing the network hardware This section assumes a working knowledge of local area network LAN operations familiarity with communications protocols that are used on interconnected LANs and familiarity with basic installation procedures for n
40. Switches Hardware Installation Manual 60 Installing BlackDiamond X8 Series Modules 4 Verify that the module injector ejector handles are open Keep the injector ejector handles in the open position as you slide the module into the chassis slot SOS ESS SSH JRL Figure 37 Installing an I O Module Note If the injector ejector handles are in the latched position they prevent the module from sliding all the way into the slot 5 Carefully slide the module into the slot until the injector ejector handles engage the edges of the chassis and begin to rotate toward the center of the module 6 Push the handles toward each other to seat the module internal connectors BlackDiamond X8 Series Switches Hardware Installation Manual 61 Installing BlackDiamond X8 Series Modules 7 Usea 2 Phillips cross head screwdriver to lock each handle into place When a locking screw is fully tightened the yellow band around the screw head is completely hidden Caution Be careful to avoid over torquing and stripping the screw heads OO III SIE LASMANIS Figure 38 Locking the Module into Place Installing I O Module Blanks Switches are shipped with a reinforcing shipping cover installed over all the I O module slots If you have the older module blanks without thumb levers see Installing I O Module Blanks without thumb levers on page 64 You nee
41. The features of these switches include Hot swappable I O modules that can provide e 10 Gigabit fiber or copper ports 40 Gigabit Ethernet ports e Ability to connect using direct atttach copper cables active optical fiber cables and SFP or QSFP optical modules 2 5u Sec port to port latency Redundant management modules that provide the CPU control subsystem N redundant switch fabric modules that provide the active switching fabric Redundant load sharing hot swappable power supplies Field replaceable hot swappable fan trays 20 Tops switching capacity 1 28 Tops bandwidth per slot Depending upon installed modules many configurations are possible including e 768 ports of IOGbE SFP per switch 2 304 ports per rack 384 ports of 100 1000 10000MbeE RJ45 per switch 1 152 ports per rack 384 ports of IGbE SFP per switch 1 152 ports per rack using IOGbE 192 ports of AOGbE QSFP per switch 576 ports per rack BlackDiamond X8 Chassis Features The BlackDiamond X8 switch chassis has the following physical features BlackDiamond X8 Series Switches u 0 u eee ee e e Height of 14 5 RU allowing three switches to be installed in a 7 foot tall standard 19 inch rack e Optional mid mount brackets for flexibility in rack positioning e Horizontal front slots for I O modules and management modules e Eight full width slots for IO modules e Two half width slots for management modules MMs e Fou
42. Weight 4 8 Ib 2 2 kg Packaged weight 7 1 lb 3 2 kg Table 21 Management Module Module Specifications BDXA MMI Length 18 inches by width 8 inches by height 2 3 inches 45 5 cm x 20 3 cm x 5 82 cm Weight 5 5 Ib 2 5 kg Packaged weight 7 9 Ib 3 5 kg Power 150 W Heat Dissipation 512 BTU Table 22 Fabric Modules Module Specifications BDXA FMIOT Length 21 inches by width 11 inches by height 4 inches 53 3 cm x 27 9 cm x 10 2 cm Weight 9 2 Ib 4 2 kg Packaged weight 12 8 Ib 5 8 kg Power 270 W Heat Dissipation 921 BTU BDXA FM20T Length 20 inches by width 10 inches by height 3 inches 50 8 cm x 25 4 cm x 7 60 cm Weight 9 2 Ib 4 2 kg Packaged weight 12 8 Ib 5 8 kg Power 330 W Heat Dissipation 1126 BTU BlackDiamond X8 Series Switches Hardware Installation Manual 114 Technical Specifications Power Supplies for BlackDiamond X8 Switches Table 23 Specifications for the BlackDiamond X8 AC Power Supply Model 48011 three power supplies Typical configuration Full configuration 8 power supplies Physical characteristics Height 1 5 inches 3 8 cm Width 4 2 inches 10 6 cm Depth 14 5 inches 36 8 cm Weight 5 3 Ib 2 4 kg Packaged weight 6 15 Ib 2 80 kg Input Rated inputs Low range 100 to 120 V 60 50 Hz 13 A maximum each power supplyHigh range 200 to 240 V 60 50 Hz 13 A maximum each power
43. X8 switch 111 modules 113 power supplies 115 text conventions 6 tools installing modules 54 installing power supplies 49 installing the chassis 45 packing the chassis 92 replacing a fabric module 73 replacing a fan tray 71 replacing a management module 79 replacing a power supply 68 replacing an I O module 82 83 transition time UPS 39 transportation conditions 113 U uninterruptible power supply see UPS unpacking the chassis 41 unshielded twisted pair 36 UPS description 39 features 39 selecting 39 transition time 39 USB port 11 14 UTP cable discharge ESD 36 RF interference 37 W weight chassis 111 fan tray 11 power supply 115 wiring closet airflow requirements 31 electrostatic discharge 31 floor coverings 30 grounding 30 humidity 30 rack securing 33 BlackDiamond X8 Series Switches Hardware Installation Manual 121
44. aining the cable is bonded to each building grounding electrode system Caution Failure to follow these requirements for cable routing conditions may expose the user to electrical shock and expose the unit to damage that can cause errors Warning The copper Ethernet ports of the equipment and its sub assemblies are suitable only for intra building connections within the same building or for connections to unexposed wiring A or cabling See the conditions listed above The copper Ethernet ports of this equipment or Aa its sub assemblies must not be metallically connected to interfaces that connect to the outside plant OSP or its wiring Copper Ethernet interfaces are designed for use only as intra building interfaces described as Type 2 or Type 4 ports in GR 1089 CORE Issue 6 and require isolation from the exposed OSP wiring The addition of Primary Protectors is not sufficient protection to connect these interfaces metallically to OSP wiring Installing Power Supply Units and Connecting Power Check the ratings and power requirements of each power supply unit or router For the ratings and power requirements of each power supply unit see Technical Specifications on page 111 of this guide or the data sheet for the power supply at www extremenetworks com Warning A Be sure to satisfy the requirements listed in this section when you install Extreme Networks power supplies When you install any power su
45. annungsquelle an wenn das Netzteil nicht im Switch eingebaut ist andernfalls kann gef hrliche Energie freigesetzt werden und es besteht potenzielle Stromschlag und Brandgefahr Stecken Sie Netzteile nur an vorschriftsm ig geerdete Netzsteckdosen an um die Gefahr eines elektrischen Stromschlages zu vermeiden und internationale Sicherheitsstandards zu erf llen Verwenden Sie nur Netzkabel die in dem jeweiligen Einsatzland zugelassen sind Versuchen Sie nicht modifizierte AC Netzkabel zu verwenden Versichern Sie sich dass Spannung und Frequenz Ihrer Steckdose mit den elektrischen Daten Ihres Ger tes bereinstimmen Das Geb ude und oder die Soannungsquelle muss gegen berlast gesch tzt sein Verwenden Sie einen berspannungsschutz einen Netzfilter oder eine unterbrechungsfreie Spannungsversorgung um das System pl tzlichen Spannungsschwankungen zu sch tzen Bei Systemen mit mehreren Netzteilen schlie en Sie jedes Netzteil an einer anderen unabh ngigen berstromschutzvorrichtung an z B an einem Sch tz Bei Ausfall einer Spannungsquelle ist nur das daran angeschlossene Netzteil betroffen F r die korrekte Auslegung des Sch tzes siehe das Datenblatt des Netzteils AC Netzteile von Extreme Networks haben keinen Ein Ausschalter Trennen Sie alle Netzstecker von den elektrischen Steckdosen um die Spannungsversorgung zu unterbrechen Achten Sie auf gute Zug nglichkeit der Steckdosen Installation von DC Netzteile
46. as Netzkabel ist der Trennschalter f r die Netzspannungsquelle Trennen Sie vor allen Arbeiten in der unmittelbaren N he von Netzteilen alle Netzkabel von der Spannungsquelle sofern die produktspezifische Wartungsanleitung nicht etwas anderes angibt Legen Sie f r alle Arbeiten an optischen Ger ten Netzteilen oder sonstigen modularen Zubeh rteilen ein geerdetes Massearmband an um das Risiko einer Besch digung des Ger tes durch elektrostatische Aufladung zu reduzieren Schlie en Sie das eine Ende des Armbands an einem geeigneten Erdungspunkt am Rack oder an einer ESD Buchse am Chassis sofern vorhanden an Lassen Sie das geerdete Massearmband am Rack oder am Chassis angeschlossen damit Sie es jederzeit parat haben wenn Sie mit Komponenten umgehen die empfindlich gegen ber elektrostatischer Aufladung sind Die Kabel sind spannungsfrei zu installieren Verwenden Sie Kabelbinder oder sonstige Zugentlastungsvorrichtungen BlackDiamond X8 Series Switches Hardware Installation Manual 105 Safety Information Kabelverlegung f r LAN Systeme Extreme Networks Ger te erf llen die Anforderungen f r Ger te f r LAN Systeme LAN Systeme sind f r geb udeinterne Installationen konzipiert das hei t die Kabel zwischen den einzelnen Einheiten m ssen im gleichen Geb ude verlaufen in dem auch die Ger te untergebracht Hiervon ausgenommen sind nur die unten aufgef hrten Bedingungen Laut de
47. bnetwork mask for VLAN default Your changes take effect immediately BlackDiamond X8 Series Switches Hardware Installation Manual 66 Installing BlackDiamond X8 Series Modules 7 Type save Your configuration changes are saved so that they will be in effect after the next system reboot The configuration is saved to the configuration database of the management modules in the switch 8 Type logout BlackDiamond X8 Series Switches Hardware Installation Manual 67 Maintaining the BlackDiamond X8 Replacing a Power Supply Replacing a Fan Tray Replacing a Fabric Module Replacing a Management Module Reseating a Management Module DIMM Packing the Chassis for Shipping The following sections contain maintenance procedures for the BlackDiamond X8 The procedures include Replacing a Power Supply on page 68 Replacing a Fan Tray on page 71 Replacing a Fabric Module on page 73 Replacing a Management Module on page 79 Reseating a Management Module DIMM on page 89 Packing the Chassis for Shipping on page 92 Replacing a Power Supply You need a 2 Phillips screwdriver to remove the power supply ventilation cover 1 Remove the power supply ventilation cover Caution a Do not operate the BlackDiamond X8 switch without the power supply ventilation cover in place This cover is required to maintain conformance to FCC emissions regulatory requirements and proper EMI levels for the switch a Loosen the reta
48. chnical training and experience necessary to be aware of the hazards to which they are exposed in performing a task and are aware of measures to minimize the danger to themselves or other persons If you are in the USA install the system in accordance with the U S National Electrical Code NEC Considerations Before Installing Consider the following items before installing equipment e The system is designed to operate in a typical data center environment that is environmentally controlled Choose a site that has the following characteristics e Temperature and humidity controlled such that the maximum ambient room temperature shall not exceed 40 C 104 F Clean and free from airborne materials Safety Information e Well ventilated and away from sources of heat including direct sunlight e Away from sources of vibration or physical shock e Isolated from strong electromagnetic fields produced by electrical devices e Secured enclosed and restricted access ensuring that only trained and qualified service personnel have access to the equipment Locate the system away from heat sources Make sure that your equipment is placed in an area that accommodates the power consumption and component heat dissipation specifications Make sure that your power supplies meet the site DC power or AC power requirements of all network equipment Do not place a monitor or other objects on top of the equipment The chassis cover is not
49. chtlinie 2004 108 Niederspannungsrichtlinie 2006 95 e UL und oder CSA gepr fte Komponente f r Nordamerika e 47 CFR Teil 15 Klasse A bei Einbau in EC Extreme Produkte BlackDiamond X8 Series Switches Hardware Installation Manual EC und der 110 9 Technical Specifications BlackDiamond X8 Switch Modules for BlackDiamond X8 Switches Power Supplies for BlackDiamond X8 Switches Connector Pinouts Conformity Statements for EMC Class A The technical specification section contains the following topics e BlackDiamond X8 Switch on page 111 e Modules for BlackDiamond X8 Switches on page 113 e Power Supplies for BlackDiamond X8 Switches on page 115 e Connector Pinouts on page 115 e Conformity Statements for EMC Class A on page 117 BlackDiamond X8 Switch Technical specifications BlackDiamond X8 Switch Technical Specifications Table 13 Physical Characteristics BlackDiamond X8 chassis Height 25 inches 63 5 cm Width 18 inches 45 7 cm Depth 30 inches 76 2 cm Note Handles on the fan trays add 1 25 inches 3 2 cm to the depth of the chassis Weight empty 187 4 Ib 85 kg Weight with 5 fan trays 218 4 Ib 99 1 kg Weight fully loaded 420 6 Ib 190 6 kg BlackDiamond X8 fan tray Height 24 inches 60 9 cm Width 4 inches 10 1 cm Depth 3 inches 7 6 cm Note Handles add 1 25 inches 3 2 cm to the depth of the fan tray Weig
50. d X8 Series Switches Hardware Installation Manual 16 BlackDiamond X8 Series Modules and Fans You can configure parameters of an I O module after it is installed or preconfigure a slot for a certain type of module and configuration The preconfigured information is applied to the module after it is inserted f Caution If you preconfigure the I O module type for a slot and then insert a different type of O module into that slot EXOS will detect amismatch and will not power on the module or generate any kind of default configuration See the ExtremexOS Concepts Guide and the ExtremexOS Command Reference Guide for feature specific information related to BlackDiamond X8 series modules BDXA 10G48X I O Module The BDXA 10G48X I O module supports 48 SFP based 10 gigabit Ethernet ports Note e BlackDiamond X8 I O modules are supplied with no pre installed optical modules
51. d X8 is powered by AC power supplies that are installed at the top front of the chassis Warning Field operators must not attempt to open the power supply enclosure for any reason the power supply does not contain user serviceable parts In the event of failure return the defective power supply to Extreme Networks for repair or replacement The power supply bay in the switch can accommodate up to eight AC power supplies Note z2 AC power supplies are ordered separately from the BlackDiamond X8 chassis The AC power supplies can operate from 110 VAC or 220 VAC and automatically adjust to the supply voltage With 220 VAC input the AC power supplies can operate in an N N or N 1 configuration Depending upon the load with 110 VAC input the AC power supplies can operate in an N N or N 1 configuration as well Power supplies in the BlackDiamond X8 are fully fault tolerant and load sharing in an N 1 configuration After the system is properly configured if one power supply fails the others provide sufficient power to operate a fully loaded switch For more information on redundancy in the BlackDiamond X8 chassis see Understanding PSU Redundancy in the BlackDiamond X8 Chassis on page 24 Understanding PSU Redundancy in the BlackDiamond X8 Chassis This section describes how N 1 and N N redundancy apply to the BlackDiamond X8 PSUs power supply units Extreme Networks sales personnel know exactly how much power should be allocat
52. d a 2 Phillips screwdriver to install a module blank After you have installed all the I O modules for your system configuration you must install module blanks in all remaining unoccupied slots Caution a All unoccupied slots in a BlackDiamond X8 series switch must have module blanks correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch BlackDiamond X8 Series Switches Hardware Installation Manual 62 Installing BlackDiamond X8 Series Modules 1 Verify that the I O module blank injector ejector handles are open Keep the injector ejector handles in the open position as you slide the I O module blank into the unoccupied chassis slot Figure 39 Installing an I O Module Blank Note 2 If the injector ejector handles are in the latched position they prevent the I O module blank from sliding all the way into the slot 2 Carefully slide the I O module blank into the slot until the injector ejector handles engage the edges of the chassis and begin to rotate toward the center of the module 3 Push the handles toward each other to seat the I O module blank BlackDiamond X8 Series Switches Hardware Installation Manual 63 Installing BlackDiamond X8 Series Modules 4 Usea 2 Phillips screwdriver to lock each handle into place When a locking screw is fully tightened the yellow band around the screw head is completely hidden
53. dass Ihre Netzteile den Gleichstrom bzw Wechselstrombedarf aller Netzwerkger te decken k nnen Racks f r Extreme Networks Ger te m ssen fest am Boden verankert werden Bei nicht vorschriftsm iger Fixierung des Racks besteht die Gefahr dass das Rack bei Wartungsarbeiten umkippt Voraussetzung f r den Betrieb des Systems ist die vollst ndige Anbringung aller Module Blenden Frontabdeckungen und r ckseitigen Abdeckungen Blenden und Abdeckplatten erf llen folgende Funktionen e Schutz vor gef hrlich hohen Spannungen und Str men im Inneren des Ger tes Eind mmung von elektromagnetischen Interferenzen EMI die andere Ger te st ren k nnten BlackDiamond X8 Series Switches Hardware Installation Manual 104 Safety Information e Vorgabe der Luftstr mungsrichtung durch das Ger t Bei der Entsorgung des Ger tes sind alle nationalen Gesetze und Vorschriften zu beachten Allgemeine Sicherheitshinweise Befolgen Sie die Richtlinien Heben Sie keine Gegenst nde die zu schwer f r Sie sind Bei der Installation von Ger ten in einem Rack platzieren Sie die schwereren Ger te in der unteren H lfte damit das Rack nicht kopflastig wird Verwenden Sie nur Werkzeuge und Ger te die sich in einem einwandfreien Zustand befinden Werkzeuge die sichtbar besch digt sind d rfen nicht benutzt werden Achten Sie bei der Verlegung von Kabeln darauf m gliche Besch digungen der Kabel zu verm
54. e a Completely loosen the retaining screws at the top and bottom of the fan tray b Holding both handles pull straight outward on the fan tray to disconnect the internal connector BlackDiamond X8 Series Switches Hardware Installation Manual 43 Installing a BlackDiamond X8 Series Chassis c Setthe fan tray aside in a safe place BEE ba LA x aS fs a EE 6 cS tee Figure 18 Removing the Fan Trays 9 Open the accessory box and locate the four lifting handles Caution Never use the handles on the fan assemblies to lift the chassis The handles and the fan assemblies are not designed to hold the weight of the chassis 10 On each side of the chassis set the pegs on the lifting handles into the mounting holes Figure 19 Preparing to Lift the Chassis from the Pallet 11 Verify that the following items are included in the shipping carton e BlackDiamond X8 chassis with installed front shipping cover and MM slot cover e Power cord retainer e Two 19 inch support brackets BlackDiamond X8 Series Switches Hardware Installation Manual 44 Installing a BlackDiamond X8 Series Chassis Checking Pre Installation Requirements In addition to the support brackets that are shipped with the chassis you need the following tools and equipment to install a chassis Mid mount bracket kit model number 48020 ordered separately from the chassis
55. e Installation Manual 39 Preparing Your Site Following Applicable Industry Standards Always follow applicable industry standards For more infor mation see the following ANSI TIA EIA standards e ANSI TIA EIA 568 A Discusses the six subsystems of a structured cabling system e ANSI TIA EIA 569 A Discusses design considerations e ANSI TIA EIA 606 Discusses cabling system administration e ANSI TIA EIA 607 Discusses commercial building grounding and bonding requirements You can access these standards at www ansi org or www tiaonline org BlackDiamond X8 Series Switches Hardware Installation Manual 40 5 Installing a BlackDiamond X8 Series Chassis Unpacking the Chassis Checking Pre Installation Requirements Rack Mounting the Chassis Grounding the Chassis Installing Power Supplies Connecting Power Cords Before you install the BlackDiamond X8 Chassis read the information in Safety Information on page 98 Installing the BlackDiamond X8 chassis requires two people to maneuver the switch and attach mounting hardware Make sure there is adequate space behind the rack to provide access for installing power supplies cables and modules The chassis should be installed before the modules and module blanks are installed The chassis is designed to fit into a standard 19 inch equipment rack Optional mid mount brackets allow you to install the chassis in a mid mount position Unpacking the Chass
56. e Installation Manual 75 Maintaining the BlackDiamond X8 c Carefully slide the module out of the switch chassis and immediately place the module into an anti static bag to protect it from potential ESD damage The bag will also prevent dust from collecting on the module connectors of A f p 8 Z A E A fo A 9 SE rl Pps the wep AE Mo UUO o o Fo o amp lo N Figure 50 Removing a Fabric Module 6 Install the replacement fabric module a Remove the module from the antistatic packaging b Loosen the screws on the insertion extraction levers and open the levers BlackDiamond X8 Series Switches Hardware Installation Manual 76 Maintaining the BlackDiamond X8 c Align the circuit board with the guides at the top and bottom of the chassis and slide the module into the chassis Figure 51 Installing a Fabric Module BlackDiamond X8 Series Switches Hardware Installation Manual 77 Maintaining the BlackDiamond X8 d When the levers start to engage push them toward the module to seat the module in the chassis e Align and tighten the retaining screws to fasten the module in place Figure 52 Securing a Fabric Module 7 Re install the removed fan tray a Set the fan tray into the chassis and push it firmly into place BlackDiamond X8 Series Switches
57. e shipped with a reinforcement shipping cover installed over all the I O module slots You need a 2 Phillips cross head screwdriver to install a module blank If you have the old I O module blanks without thumb levers see Installing I O Module Blanks Without Thumb Levers on page 88 After you have installed all the I O modules for your system configuration you must install module blanks in all remaining unoccupied slots Caution All unoccupied slots in a BlackDiamond X8 series switch must have module blanks correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch BlackDiamond X8 Series Switches Hardware Installation Manual 86 Maintaining the BlackDiamond X8 1 Verify that the I O module blank injector ejector handles are open Keep the injector ejector handles in the open position as you slide the I O module blank into the unoccupied chassis slot Figure 62 Installing an I O Module Blank Note 2 If the injector ejector handles are in the latched position they prevent the I O module blank from sliding all the way into the slot 2 Carefully slide the I O module blank into the slot until the injector ejector handles engage the edges of the chassis and begin to rotate toward the center of the module 3 Push the handles toward each other to seat the I O module blank BlackDiamond X8 Series Switches Hardware Installation Ma
58. e tie wraps or other strain relief devices Replace a power cord immediately if it shows any signs of damage General Safety Precautions Follow safety guidelines to avoid injury Do not attempt to lift objects that you think are too heavy for you When you install equipment in a rack load heavier devices in the lower half of the rack first to avoid making the rack top heavy BlackDiamond X8 Series Switches Hardware Installation Manual 99 Safety Information e Only use tools and equipment that are in perfect condition Do not use equipment with visible damage e Route cables in a manner that prevents possible damage to the cables and avoids causing accidents such as tripping Cable Routing for LAN Systems Extreme Networks equipment meets the requirements for LAN system equipment LAN systems are designed for intra building installations that is cable runs between devices must be in the same building as the connected units except under the conditions listed in the next paragraph As allowed in the USA by the National Electrical Code NEC this equipment can be connected between buildings if any one of the following conditions is true e Cable runs between buildings are less than 140 feet long e Cable runs between buildings are directly buried e Cable runs between buildings are in an underground conduit where a continuous metallic cable shield or a continuous metallic conduit cont
59. ed for each module in a customer s system and the maximum power output each PSU can deliver Extreme Networks sales personnel will determine how many PSUs are needed for each installation to achieve the desired redundancy This section contains the following topics e Power System Redundancy Overview on page 25 e N lRedundancy on page 25 e N N Redundancy on page 25 e Simultaneous N and N N Redundancy on page 25 Understanding Power Supplies Power System Redundancy Overview The BlackDiamond X8 chassis has slots for eight PSUs There is a power connector on the back for each PSU If all populated PSUs are powered from 220VAC then each PSU is capable of supplying about 2500W to the chassis If any PSU is powered by 120VAC then each PSU is capable of supplying about 1250W Note 2500W and 1250W are approximations When several PSUs are installed in a system the actual power per PSU decreases by up to 10 This decrease is taken into account when a system is configured N Redundancy To guarantee that the BlackDiamond X8 will operate properly in the event of a single PSU failure the user must calculate how many PSUs are required to power all the modules and fan trays in the configuration Do the following to calculate the number of PSUs required for N 1 redundancy 1 Add up the power consumptions of all the MMs IOBs FMs and Fan Trays in the system 2 Divide the total power consumption by either 2500 or 1250
60. eiden und Risiken z B Stolpergefahren auszuschalten Stellen Sie keinen Bildschirm oder anderen Gegenst nde auf die Ger te Die Chassisabdeckung ist keine Abstellfl che Zum Schutz vor Selbstentz ndung verwenden Sie nur Daten bertragungskabel der Gr e 26 AWG oder gr er Verwenden Sie nur Kupferleiter Arbeiten Sie w hrend eines Gewitters nicht an dem System und stecken Sie keine Kabel an oder ab Das Ger t muss geerdet werden Der Schutzleiter darf nicht manipuliert oder umgangen werden und das Ger t darf auf keinen Fall ohne einen entsprechend installierten Schutzleiter betrieben werden Sicherheit bei Wartungsarbeiten Befolgen Sie bei allen Wartungsarbeiten an Extreme Networks Ger ten folgende Empfehlungen Verwenden Sie nur zugelassene Zubeh rteile oder Komponenten die f r den Einsatz mit diesem System genehmigt sind Eine Missachtung dieser Hinweise kann zu einer Besch digung des r Ger te s f hren und die einschl gigen Sicherheits und EMV Vorschriften verletzen Das System enth lt keinerlei Teile die vom Benutzer zu warten sind Versuchen Sie nicht Chassis Netzteil Modul oder andere Komponenten eigenm chtig zu reparieren Senden Sie im Falle einer St rung das defekte Teil zur Reparatur oder zum Austausch an Extreme Networks ein sofern ein Extreme Networks Vertreter nicht etwas anderes angibt Um das System spannungslos zu machen m ssen Sie alle Netzkabel aus den Netzsteckdosen ziehen D
61. electing Po Battery Repl Sicherheitshi ns Before Installing 98 Safety 99 ty Precautions 99 Cable Routing for LAN Systems 100 nstalling Power Supply Units and Connecting Power 100 wer Supply Cords 101 acement and Disposal 102 Fiber Optic Ports and Optical Safety 102 nweise 104 Uberlegungen vor der Installation 104 Allgemeine Sicherheitshinweise 105 Sicherheit bei Wartungsarbeiten 105 Kabelverlegung f r LAN Systeme 106 nstallation d Auswahl der LWL Ports u er Netzteile und Netzanschluss 106 Netzkabel 108 Wechseln und Entsorgen der Batterie 108 nd optische Sicherheit 109 Chapter 9 Technical Specifications 111 Modules for Power Suppl Connector P BlackDiamond X8 Switch 111 BlackDiamond X8 Switches 113 ies for BlackDiamond X8 Switches 115 inouts 115 Conformity Statements for EMC Class A 117 Index 119 BlackDiamond X8 Serie s Switches Hardware Installation Manual Preface This guide provides the instructions and supporting information needed to install the Extreme Networks BlackDiamond X8 series switch The guide includes information about site preparation and switch functionality Using Hardware Publications Online You can access hardware publications at the Extreme Networks website www extremenetworks com Publications are provided in HTML ePub and Adobe PDF formats To navigate this guide online use the table of contents found in the navigation bar
62. er cksichtigen Sie vor der Installation der Ger te folgende Punkte W hlen Sie f r Ger te die in einer typischen Telekommunikationsumgebung mit kontrollierten Umweltbedingungen eingesetzt werden einen Ort mit folgenden Merkmalen e Temperatur und Feuchtigkeit werden kontrolliert und die maximale Raumtemperatur liegt nicht ber 40 C e Sauber und frei von in der Luft enthaltenen Stoffen die Elektrizit t bertragen k nnen e Gut bel ftet und fern von Warmequellen inklusive direkter Sonneneinstrahlung Fern von Quellen f r Ersch tterungen oder mechanische Einwirkungen e Getrennt von starken elektromagnetischen Feldern die von elektrischen Ger ten erzeugt werden Bei Ger ten die nicht f r eine Installation in Umgebungen mit kontrollieren Umweltbedingungen vorgesehen sind wie z B Geh use im Freien beachten Sie bitte das Produktdatenblatt oder Anhang B dieser Anleitung mit den Spezifikationen f r Umgebungsbedingungen Temperatur und Feuchtigkeit Lassen Sie auf allen Seiten mindestens 3 Zoll Platz um eine ausreichende Luftzirkulation zu gew hrleisten Die L ftungsschlitze an der Vorder oder R ckseite und an den Seiten d rfen nicht blockiert werden Stellen Sie das System nicht in der N he von Warmequellen auf Versichern Sie sich dass Ihre Ger te in einem Bereich aufgestellt werden der f r den Stromverbrauch und die damit verbundene W rmestrahlung der Komponenten geeignet ist Versichern Sie sich
63. eries Switches Hardware Installation Manual 92 Maintaining the BlackDiamond X8 2 Remove all the fan trays one at atime a Completely loosen the retaining screws at the top and bottom of the fan tray b Holding both handles pull straight outward on the fan tray to disconnect the internal connector c Set the fan tray aside in a safe place Figure 71 Removing the Fan Trays 3 Remove all the installed modules including any module blanks For more information on removing modules see e Replacing a Management Module on page 79 e Removing an I O Module on page 82 e Replacing a Fabric Module on page 73 4 Atthe front of the chassis attach the shipping cover over the I O module slots Removing the Chassis from the Rack Once you have prepared for chassis removal then remove the chassis from the rack 1 Onthe back of the chassis remove the screws from the ground lug to disconnect the ground wire from the chassis 2 Using four mounting screws attach the support brackets to the equipment rack immediately below the chassis 3 Remove the rack mounting screws that secure the chassis to the rack Slowly guide the chassis out of the equipment rack using the support bracket for support BlackDiamond X8 Series Switches Hardware Installation Manual 93 Maintaining the BlackDiamond X8 5 Attach the lifting handles to each side of the chassis 6 Carefully lift the chassis o
64. es and I O modules e Bays for redundant power supplies with ventilated cover BlackDiamond X8 Series Switches Hardware Installation Manual 9 BlackDiamond X8 Series Switches e Connection point for ESD preventive strap The following figure shows the back of the BlackDiamond X8 chassis 3 ML Tee Figure 2 Back of the BlackDiamond X8 Chassis 1 Grounding point 3 AC power input connectors 2 ESD jack 4 Fan trays The back of the chassis provides access to e Eight AC power input connectors e Five vertical fan trays e Four fabric module slots behind the fan trays e Connection point for ESD preventive strap e Attachment point for optional chassis ground 1 in the Figure 2 Back of the BlackDiamond X8 Chassis on page 10 BlackDiamond X8 Series Switches Hardware Installation Manual 10 BlackDiamond X8 Series Switches Management Module Ports Overview Each BlackDiamond management module MM has a 10 100 1000BASE TX Ethernet management port The management port enables direct communication with the central processing unit CPU of the switch IT personnel can plug an Ethernet cable directly from a laptop into the management port for direct access into the switch This access allows viewing and local management of the switch configurations USB ports on the managemen
65. esting laboratory UL evaluates the 333 Pfingsten Road performance and capability of electrical wiring and equipment Northbrook Illinois to determine whether they meet certain safety standards 60062 2096 when properly used Acceptance is usually indicated by the USA words UL Approved or UL Listed National Electrical Manufacturing Association NEMA USA NEMA http only 1300 N 17th Street www nema org Organization of electrical product manufacturers Members Rosslyn Virginia 22209 develop consensus standards for cables wiring and electrical USA components Electronics Industries Alliance EIA EIA http www eia org Trade association that develops technical standards 2500 Wilson Boulevard disseminates marketing data and maintains contact with Arlington Virginia 22201 government agencies in matters relating to the electronics USA industry Federal Communications Commission FCC USA only FCC http www fcc gov Commission that regulates all interstate and foreign electrical 445 12th Street S W communication systems that originate in the United States Washington D C 20554 according to the Communications Act of 1934 The FCC USA regulates all U S telephone and cable systems BlackDiamond X8 Series Switches Hardware Installation Manual 29 Preparing Your Site Checking Equipment Location Recommendations for your equipment location Note e We recommend that you con
66. etworking equipment Note Before installing or removing any components of the system or before carrying out any maintenance procedures read the safety information in BlackDiamond X8 Series Switches of this guide Planning Your Site By carefully planning your site you can maximize the performance of your existing network and ensure that it is ready to migrate to future networking technologies The site planning process has three major parts 1 Meet site requirements The physical installation site must meet the following requirements for a safe and successful installation e Building and electrical code requirements e Environmental safety and thermal requirements for the equipment you plan to install e Equipment rack requirements 2 Evaluate and meet cable requirements Evaluate and compare your existing cable plant with the requirements of the Extreme Networks equipment to determine if you need to install new cables 3 Meet power requirements To run your equipment safely you must meet the specific power requirements for each component and external power supply unit installed in each system For BlackDiamond X8 power supply specifications see Power Supplies for BlackDiamond X8 Switches on page 115 Meeting Site Requirements The following sections describe the requirements for your operating environment cables and power Preparing Your Site Meeting Operating Environment Requirements Learn the regulatio
67. fekte Netzteil zur Reparatur oder zum Austausch an Extreme Networks ein Fassen Sie nicht mit der Hand in einen offenen Netzteileinschub wenn das Netzteil entfernt wurde Legen Sie vor allen Arbeiten an einem an Leistungskabeln angeschlossenen Ger t s mtlichen Schmuck sowie Ihre Armbanduhr ab Im Falle eines Kurzschlusses Kontakt mit Leistung und Erde erw rmen sich Metallgegenst nde was zu ernsthaften Verbrennungen f hren oder den Metallgegenstand mit den Anschl ssen verschwei en kann Legen Sie vor allen Arbeiten an einem an Leistungskabeln angeschlossenen Ger t s mtlichen Schmuck sowie Ihre Armbanduhr ab Metallgegenst nde erw rmen sich wenn sie an Leistung und an Erde angeschlossen werden was zu ernsthaften Verbrennungen f hren oder den Metallgegenstand mit den Anschl ssen verschwei en kann Wenn das Netz bei angeschlossener Netzversorgung angeschlossen oder getrennt wird kann ein elektrischer Lichtbogen entstehen Dies kann bei Installationen in Gefahrenbereichen zu einer Explosion f hren Achten Sie unbedingt darauf dass das Ger t nicht mit der Netzversorgung verbunden ist Achten Sie bei der Installation oder beim Austausch von Ger ten darauf dass Sie zuerst den Erdungsanschluss herstellen bzw den Erdungsanschluss zuletzt trennen Bei Installation von AC Netzteilen Schlie en Sie bei Switches mit einem vor Ort austauschbaren Netzteil die Spannungsversorgung nicht an einer elektrischen Sp
68. ff the support bracket and lower it onto the wood pallet see Setting the Chassis on the Shipping Pallet 7 Re install the removed fan trays a Set each fan tray into the chassis and push it firmly into place b Align and tighten the retaining screws 9 Figure 72 Installing a Fan Tray Caution a Do not use the fan tray handles to lift or maneuver the chassis The handles on the fan trays are not designed to support the weight of the chassis BlackDiamond X8 Series Switches Hardware Installation Manual 94 Maintaining the BlackDiamond X8 8 Remove the mid mount brackets and lifting handles from th Figure 73 Setting the Chassis on the Shipping Pallet Assembling the Shipping Container Once the chassis is removed assemble the shipping container around it 1 pallet Figure 74 Recrating the BlackDiamond X8 Chassis BlackDiamond X8 Series Switches Hardware Installation Manual e sides of the chassis Ateach corner attach a restraining bolt to the shipping bracket securing the chassis to the shipping 95 Maintaining the BlackDiamond X8 2 Put the lower foam cushion around the base of the chassis and set the upper foam cap on top of the chassis Figure 75 Placing the Foam Cushioning Around the Chassis 3 Seta corner brace at each corner of the chassis and slide the shipping carton down over
69. h installed module blank before inserting additional modules or blanks Otherwise you might unseat modules or blank front panels that you have not secured Applying Power and Accessing the Chassis for the First Time After you have installed all of the modules and module blanks apply power to the chassis After the BlackDiamond X8 has completed all power on self tests it is operational To access the chassis appropriate cables are available from your local supplier or you can make your own To ensure the electromagnetic compatibility of the unit use only shielded serial cables For information about the DB 9 console plug connector see Connector Pinouts on page 115 You can log in and configure an IP address for the default VLAN named default Note In BlackDiamond switches the management port on the management module is part of the management VLAN by default Refer to Management Module Ports Overview on page 11 for further details BlackDiamond X8 Series Switches Hardware Installation Manual 65 Installing BlackDiamond X8 Series Modules Using the Console Port Connection to the console port is used for direct local management The terminal or PC with terminal emulation software that you connect to an Extreme Networks switch must be configured with the following settings to access the BlackDiamond X8 through the console port Baud rate 9600 Data bits 8 Stop bit 1 Parity None Flow control XON XOFF N
70. harp bends can destroy or impair the cable s ability to convey light pulses accurately from one end of the cable to the other Use care in dressing the optical fiber cables provide satisfactory strain relief to support the cable and maintain an adequate bend radius at all cable turns particularly where the cable connects to the I O module Figure 13 Bend Radius for Fiber Optic Cable 1 Minimum 2 inch 51 mm radius in 90 bend Preventing Radio Frequency Interference If you use UTP cabling in an installation take precautions to avoid RF interference RF interference can cause degradation of signal quality and in an Ethernet network environment can cause excessive collisions loss of link status or other physical layer problems that can lead to poor performance or loss of communication 1 Avoid the following situations a Attaching UTP cable to AC power cables b c d e f Ro Ro Ro Ro Ro utin utin utin utin g UT gU equipmen gU gU utin gu P cable n TP cable n t TP cable n TP cable n P cable n ear antennas such as a ham radio antenna ear equipment that could exhibit RF interference such as ARC welding ear electrical motors ear air conditioner units ear electrical transformers 2 Inareas or applications where these situations cannot be avoided use fiber optic cabling or shielded twisted pair cabling STP Meeting Power Requirement
71. he management modules operates as the primary and the other becomes the secondary or backup The management modules are solely responsible for upper layer protocol processing and system management functions and do not carry data plane traffic between I O slots When you save the switch configuration it is saved to all installed management modules Selection of the primary management module occurs automatically The following examples describe the selection process e When a switch boots with two management modules installed the management module in slot A becomes the primary If a switch is operating with one management module and a second management module is added to the switch after it has been powered up the added management module becomes the secondary Management modules operating in secondary or backup mode can be inserted and removed without disrupting network services e f you remove the primary management module while the switch is operating the secondary management module becomes the primary management module For example if you have a switch with a primary management module in slot A and a secondary management module in slot B and you remove the primary management module from slot A the secondary or backup management module in slot B becomes the primary Features of the Management Module Management modules have the following features on the front panel e Managementl port The 10 100 1000BASE T Ethernet management
72. ht 6 2 Ib 2 8 kg Fan speed 2 500 12 000 RPM 10 Power input socket IEC 320 C20 Power supply cord selection Refer to Selecting Power Supply Cords Technical Specifications Table 14 Safety Standards North American UL 60950 1 2007 2nd Ed or UL 60950 1 Ist Ed 2007 as applicable US cULus listed to CSA 22 2 No 60950 1 07 Canada FCC 21 CFR 1040 10 US Laser Safety CDRH Letter of Approval US FDA Approval European International CB Scheme IEC 60950 1 2005 2nd Ed with national differences GS Mark EN 60950 1 2006 ATl EN 60825 1 2007 EU Laser Safety 2006 95 EC Low Voltage Directive AS NZS 60950 1 Australia New Zealand Mexico NOM 19 NRTL Russia GOST R Table 15 EMI EMC Standards North American FCC CFR 47 part 15 2009 Class A US ICES 003 Issue 4 2004 Class A Canada European EN 55022 2006 A1 2007 Class A EN 55024 1998 A1 2001 A2 2003 EN50121 4 2006 EN IEC 61000 3 2 2006 A2 2009 Harmonics EN IEC 61000 3 3 2009 Flicker EN IEC 61000 4 2 Ed 2 0 2008 Electrostatic Discharge 8kV Contact 5kV Air Criteria A EC EN 61000 4 3 Ed 3 2 2010 Radiated Immunity 80 1GHz 20V m 000 2100 10V m 2100 2700 5V m Criteria A 61000 4 4 Ed 2 0 2010 Transient Burst 2kV Criteria A 61000 4 5 Ed 2 0 2010 Surge 1 2kV Criteria A 61000 4 6 Ed 3 0 2008 Conducted Immunity 0 15 80MHz s unmod Criteria A 61000 4 11 Ed 2 0 2004 Power Dips amp Interruptions gt 30 25 periods Cri
73. ilung f r Ihre Installation in Ihrem Land an einen Elektrofachbetrieb zu wenden Auswahl der Netzkabel Anforderungen an das Netzkabel entnehmen Sie Anha how to buy how to buy aspx Note m Lieferumfang von Extreme Networks Produkten sind keine Netzkabel enthalten Ein f r Ihr Produkt und Land passendes Netzkabel erhalten Sie entweder von Ihrem zust ndigen Extreme Networks Channel Account Manager oder Sales Manager oder im rtlichen Fachhandel Die ng B zu dieser Anleitung Hier finden Sie Ihren zust ndigen Sales Manager oder Fachh ndler http www extremenetworks com Dieses Ger t ist nicht f r eine direkte Versorgung von einem Spannungsverteilungssystem vorgesehen wo die Leiter Leiter Spannung den Wert von 240 VAC 2 Phasen Schutzerde wird ein Transformator empfohlen um die Spannung auf einen Wert unter lt 240 VAC e wie zum Beispiel in Norwegen Frankreich und anderen L ndern F r derartige Anwendungen Leiter Leiter herunterzutransformieren oder ein Anschluss an eine P N Schutzerde Spannungsverteilung wo die Spannung 240 VAC nicht berschreitet Alle Installationen m ssen eine zuverl ssige Erdung gem den nationalen Elektrovorschriften vorsehen Wechseln und Entsorgen der Batterie Die Batterien in Extreme Produkten sind gekapselt und d rfen nur durch qualifiziertes Extreme Wartungspersonal ausgewechselt werden BlackDiamond X8 Series Switches Hardware Installati
74. imes degrade with increased temperature If possible temperatures should be kept at approximately 78 F 25 C or lower 1 Be sure that the ventilation in the wiring closet is adequate to maintain a temperature below 104 F 40 Install a reliable air conditioning and ventilation system Keep the ventilation in the wiring closet running during non business hours otherwise the equipment can overheat A Maintain an ambient operating temperature of 32 to 104 F 0 to 40 C 5 Maintain a storage temperature of 40 to 158 F 40 to 70 C Controlling Humidity Maximize equipment life by keeping relative humidity between allowable limits Keep operating humidity between 50 and 70 relative humidity non condensing during typical operation BlackDiamond X8 Series Switches Hardware Installation Manual 30 Preparing Your Site Following Spacing and Airflow Requirements Be sure that walls and other equipment do not block the air intake or outflow on an Extreme Networks switch 1 Leave a minimum of 24 inches 61 cm between any solid wall or other obstruction and the front and back of the chassis Measure the air temperature approximately 1 inch 2 5 cm from the front of I O slot 1 The temperature should be less than 104 F 40 C Protecting from Electrostatic Discharge Your system must be protected from static electricity or electrostatic discharge ESD 1 Remove materials that can ca
75. ining screws at the top corners of the cover panel b Pull outward on the retaining screws to tilt the cover panel away from the front of the chassis Maintaining the BlackDiamond X8 c Liftthe cover panel away from the chassis Figure 42 Removing the Power Supply Ventilation Cover 2 Push the release button for the inserter extractor lever on the front of the power supply 3 Rotate the inserter extractor lever to the right to unseat the power supply from the internal connectors BlackDiamond X8 Series Switches Hardware Installation Manual 69 Maintaining the BlackDiamond X8 4 Carefully slide the power supply out of the chassis and set it aside Figure 43 Removing a Power Supply 5 Onthe front of the replacement power supply push the release button for the insertion ejector lever 6 Slide the power supply into the chassis until the lever starts to engage Figure 44 Installing a Power Supply BlackDiamond X8 Series Switches Hardware Installation Manual 70 Maintaining the BlackDiamond X8 7 Rotate the lever toward the front of the power supply to fully seat the power supply in the chassis 8 Replace the power supply ventilation cover a Setthe lower edge of the cover in place so that the tabs on the edge fit into the matching slots in the chassis frame b Rotate the top of the cover into place against the front of the chassis frame Align and tighten the retaining screws
76. insertion extraction levers and open the levers Caution To prevent ESD damage hold the module by the metal rail and front panel only Never touch the components on the PCB or the pins on any of the connectors Figure 32 Installing a Fabric Module b Align the circuit board with the guides at the top and bottom of the chassis and slide the module into the chassis BlackDiamond X8 Series Switches Hardware Installation Manual 56 Installing BlackDiamond X8 Series Modules c When the levers start to engage push them toward the module to seat the module in the chassis d Align and tighten the retaining screws to fasten the module in place Figure 33 Securing a Fabric Module 5 Repeat these steps to install additional fabric modules 6 Re install the removed fan trays a Set each fan tray into the chassis and push it firmly into place BlackDiamond X8 Series Switches Hardware Installation Manual 57 Installing BlackDiamond X8 Series Modules b Align and tighten the retaining screws 9 Figure 34 Installing a Fan Tray Installing Management Modules Slots for management modules are labeled A and B Install the first management module in slot A 1 Attach the ESD preventive wrist strap to your bare wrist 2 If itis not already connected connect
77. is Use this procedure to safely remove the chassis from the box Caution a An unpopulated BlackDiamond X8 chassis weighs approximately 152 pounds 69 kg as shipped Lifting the BlackDiamond X8 chassis safely requires a minimum of two people or appropriate lifting equipment Note e Save all packaging bolts and washers as well as the box and pallet for future use in the event that the chassis must be moved to another location or returned to Extreme Networks Refer to the illustrations printed on the BlackDiamond X8 shipping container and unpack the chassis and accessories Installing a BlackDiamond X8 Series Chassis 1 Cut the straps around the box Figure 14 Unstrapping the Box 2 Slide the box up and off the chassis and interior packing foam Figure 15 Removing the Box 3 Remove the inside corner braces 4 Remove the support brackets and boxed accessories and set them aside until you need them 5 Lift off the upper packing foam BlackDiamond X8 Series Switches Hardware Installation Manual 42 Installing a BlackDiamond X8 Series Chassis 6 Pull apart the keyed corner of the lower packing foam and remove the lower packing foam from around the chassis Figure 16 Removing the Accessories and Foam 7 On each side remove the restraining bolts from the shipping brackets at the front and middle of the chassis Figure 17 Unbolting the Chassis 8 Remove all the fan trays one at a tim
78. is necessary If you build your own cable be sure that connectors are properly crimped or safety and fire rating requirements Consult you Provide enough slack approximately 2 to 3 inches 50 to 75 mm to provide proper strain relief When installing a patch panel using twisted pair wiring untwist no more than 0 25 inches 0 64 Discharge the RJ 45 Ethernet cable before plugging it into a port on the BlackDiamond X8 local building codes to determine when it is appropriate to use plenum rated cable or refer to IEC standard 850 10 Keep all ports and connectors free of dust Caution new installation Before connecting any cable to the switch discharge ESD from the cable A Unshielded twisted pair UTP cable can build up ESD charges when being pulled into a by plugging the RJ 45 connector into aLAN Static Discharge device or use an equivalent method Fiber Optic Cable Fiber optic cable must be handled carefully during installation Every cable has a minimum bend radius and fibers will be damaged if the cables are bent too sharply It is also important not to stretch the cable during installation We recommend that the bend radius for BlackDiamond X8 Series Switches Hardware Installation Manual 36 Preparing Your Site fiber optic cable equal 2 inches 51 mm minimum for each 90 degree turn as shown in Figure 13 Bend Radius for Fiber Optic Cable on page 37 Note Kinks and s
79. ks For an initial system installation the recommended order for installing modules and module blanks into the chassis is Install all fabric modules FMs Install all management modules MMs Install MM blanks in any unoccupied slot Install I O modules Install I O blanks in any unoccupied slot nn KRW NY Z Apply power to the chassis Required Tools You need the following tools and equipment to install modules e ESD preventive wrist strap e 2 Phillips screwdriver for the retaining screws on the fan tray and locking screws on management and I O modules 5 16 inch flat tip screwdriver for the retaining screws on the fabric module Installing BlackDiamond X8 Series Modules Installing Fabric Modules Install all the fabric modules before you install I O modules The slots for fabric modules are numbered 1 through 4 from left to right If you are installing only three fabric modules use slots 1 through 3 1 Attach the ESD preventive wrist strap to your bare wrist 2 If itis not already connected connect the metal end to the receptacle at the right of the power input connectors 3 Remove the fan tray from each location where you will install a fabric module Figure 31 Removing a Fan Tray A Install each fabric module BlackDiamond X8 Series Switches Hardware Installation Manual 55 Installing BlackDiamond X8 Series Modules a Loosen the screws on the
80. l 0 a a a il a a a 0 T Figure 70 Push to reseat the DIMM yay we H Caution To avoid damage the DIMM is polarized and will not go in the socket when rotated in the wrong direction Repeat steps 6 through 9 for the second DIMM Packing the Chassis for Shipping Prepare remove and assemble the shipping box for returning the chassis You need the following tools and materials to pack a chassis Original shipping cover for the front module slots Lifting handles that were shipped with the chassis Original shipping box and packing materials Screwdriver for ground lug screws Four rack mounting screws for attaching the support brackets to the rack ifthey have been removed 2 Phillips screwdriver for removing the chassis from the rack Nylon package strapping material and a crimping tool Perform the following steps to pack the chassiss for shipping RW MN Set the pallet in a convenient stable location near the equipment rack Prepare the chassis for removal Remove the chassis from the rack Assemble the shipping container Preparing the Chassis for Removal To prepare the chassis for removal from the rack remove the installed modular components 1 Turn off the power to the chassis and remove the installed power supplies a Remove the power cord retainer and disconnect all power cords b Remove all the installed power supplies BlackDiamond X8 S
81. l affect only the power supplies to which it is connected If all BlackDiamond X8 power supplies are connected to a single power source the entire chassis is vulnerable to a power source failure Extreme Networks AC power supplies do not have switches for turning the unit on and off Disconnect all AC power cords to remove power from the BlackDiamond X8 Chassis Make sure that these connections are easily accessible Selecting Power Supply Cords Extreme Networks does not provide power input cords in the product box To purchase a power cord for your product and for your specific country contact your local Extreme Networks Channel Account Manager or Sales Manager or purchase a cord from your local supplier Requirements for the power cord are listed in Technical Specifications on page 111 To locate a Sales Manager or Partner in your region visit http www extremenetworks com how to buy how to buy aspx Caution This equipment is not intended to be directly powered by power distribution systems where N phase phase voltages exceed 240VAC 2P PE such as those used in Norway France and other countries For these applications it is recommended that a transformer be used to step down the voltage to lt 240VAC from phase phase or that you make a connection to a P N PE power distribution where voltages do not exceed 240VAC All installations should confirm that the product is reliably grounded according to the country
82. loor as shown in Figure 12 Properly Secured Rack on page 32 a hr oo 00 00 00 00000000 eo 000000000000 0000000 00000000000000000000000000007 oof Figure 12 Properly Secured Rack 2 Brace open equipment racks if the channel thickness is less than 1 4 inch 6 4 mm Evaluating and Meeting Cable Requirements The following sections describe the cable requirements Cabling Standards Use professional consultants for site planning and cabling We recommend using the Building Industry Consulting Service International BICSI Registered Communications Distribution Designer RCDD which is globally recognized as a standard in site planning and cabling For information go to www bicsi org Labelling Cables A reliable cable labeling system is essential when planning and installing a network Maintaining accurate records helps you to e Relocate devices easily e Make changes quickly e Isolate faults in the distribution system BlackDiamond X8 Series Switches Hardware Installation Manual 33 Preparing Your Site e Locate the opposite end of any cable e Know the types of network devices that your cabling infrastructure can support Do the following to properly label your cables 1 Identify cables by securely attaching labels to all cable ends 2 Assign a unique block of sequential numbers to the group of cables that run between each pair of equipment locations 3 A
83. m US amerikanischen National Electrical Code NEC darf diese Ausr stung zwischen Geb uden verbunden werden sofern eine der folgenden Bedingungen erf llt ist e Die L nge der zwischen Geb uden verlegten Kabel betr gt h chsten 140 Fu e Die Kabel sind zwischen den Geb uden direkt erdverlegt e Die Kabel zwischen den Geb uden sind in einem unterirdischen Kanal verlegt wobei ein durchgehender metallischer Kabelschirm oder eine durchgehende Metallleitung die das Kabel umschlie t an den Erdungselektrodensystemen der einzelnen Geb ude angeschlossen ist Caution Eine Missachtung dieser Bedingungen f r die Kabelverlegung kann Nutzer der Gefahr eines elektrischen Stromschlages aussetzen und das Ger t so besch digen dass es nicht mehr einwandfrei arbeitet Die Ethernet Anschl sse des Ger tes und der zugeh rigen Baugruppen sind nur f r geb udeinterne innerhalb ein und desselben Geb udes Verbindungen oder f r Anschl sse an nicht exponierte Verdrahtungen oder Verkabelungen geeignet siehe die oben aufgef hrten Bedingungen Die Ethernet Anschl sse des Ger tes und der zugeh rigen Baugruppen d rfen nicht mit Metallkontakt an Schnittstellen angeschlossen werden die mit einer externen Anlage Outside Plant OSP oder deren Verdrahtung verbunden sind Ethernet Schnittstellen sind nur f r eine Verwendung als geb udeinterne Schnittstellen konzipiert sog Ports vom Typ 2 oder Typ 4 gem GR 1089 CORE Ausgabe 6 und m sse
84. module slots 5 Holding the module by the metal rail and front panel only remove the module from the antistatic packaging Caution A To prevent ESD damage never touch the components on the PCB or the pins on any of the connectors BlackDiamond X8 Series Switches Hardware Installation Manual 84 Maintaining the BlackDiamond X8 6 Verify that the module injector ejector handles are open Keep the injector ejector handles in the open position as you slide the module into the chassis slot Figure 60 Installing an I O Module Note If the injector ejector handles are in the latched position they prevent the module from sliding all the way into the slot 7 Carefully slide the module into the slot until the injector ejector handles engage the edges of the chassis and begin to rotate toward the center of the module 8 Push the handles toward each other to seat the module internal connectors BlackDiamond X8 Series Switches Hardware Installation Manual 85 Maintaining the BlackDiamond X8 9 Usea 2Phillips screwdriver to lock each handle into place When a locking screw is fully tightened the yellow band around the screw head is completely hidden Caution Be careful to avoid over torquing and stripping the screw heads OO III SIE LASMANIS Figure 61 Locking the Module into Place Installing I O Module Blanks Switches ar
85. n durch Isolierung von exponierter OSP Verdrahtung getrennt werden Prim re Protektoren sind kein ausreichender Schutz f r den Anschluss dieser Schnittstellen ber einen Metallkontakt mit OSP Verdrahtung Diese Warnung gilt nicht f r Ports vom Typ TIYEI weil diese Ports ber eine integrierte Isolierung und einen Schutz vor Spannungsspitzen verf gen der den Anschluss an OSP Verdrahtung gestattet Installation der Netzteile und Netzanschluss Die Leistungsdaten und die Anforderung der einzelnen Netzteile an den Leistungseingang entnehmen Sie bitte Anhang B dieser Anleitung oder dem Datenblatt f r die Netzversorgung unter http www extremenetworks com Die Leistungsdaten und die Anforderung der einzelnen Netzteile an den Leistungseingang entnehmen Sie bitte Anhang B dieser Anleitung oder dem Datenblatt f r die Netzversorgung unter http www extremenetworks com Warning A Die in diesem Abschnitt aufgef hrten Anforderungen m ssen bei der Installation von Extreme Networks Netzteilen und beim Netzanschluss unbedingt erf llt werden BlackDiamond X8 Series Switches Hardware Installation Manual 106 Safety Information Bei Installation eines Netzteils Schieben Sie das Netzteil nicht mit Gewalt in den Einschub Versuchen Sie nicht das Geh use des Netzteils zu ffnen das Netzteil enth lt keinerlei Teile die vom Nutzer zu warten sind Senden Sie im Falle einer St rung das de
86. n a BlackDiamond X8 series switch must have module blanks correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch Installing a Management Module Blank Install a blank management module in every unoccupied management slot i Caution If a management module is not installed in a slot you must install a blank cover over the slot to maintain proper EMI levels and ventilation to ensure conformance to FCC requirements and to maintain adequate airflow through the switch 1 Set the blank in place over the open slot 2 Align and tighten the captive retaining screws Installing I O Modules Slots for I O modules are numbered 1 through 8 starting at the top Caution All unoccupied I O module slots must be covered by I O module blanks to ensure proper TAN system ventilation and EMI compliance Individual I O module blanks are purchased separately from the chassis See Installing I O Module Blanks on page 62 to install O blanks 1 Attach the ESD preventive wrist strap to your bare wrist 2 If itis not already connected connect the metal end to the receptacle between the management module slots 3 Holding the module by the metal rail and front panel only remove the module from the antistatic packaging Caution To prevent ESD damage never touch the components on the PCB or the pins on any of the connectors BlackDiamond X8 Series
87. n und Anschluss von Gleichspannung BlackDiamond X8 Series Switches Hardware Installation Manual 107 Safety Information e Der Anschluss an die Gleichspannungsauelle Ihrer Einrichtung muss von einem qualifizierten gepr ften Elektriker vorgenommen werden e DC Netzteile von Extreme Networks haben keinen Ein Ausschalter Versichern Sie sich dass der DC Kreis spannungslos ist ehe Sie das Gleichstrom oder abstecken abel an einer Gleichstromeingangsbuchse an e Schlie en Sie eine Gleichstromversorgung nicht an die DC Quelle an wenn das Netzteil nicht im Chassis eingebaut ist andernfalls kann gef hrliche Energie freigesetzt werden und es besteht potenzielle Stromschlag und Brandgefahr e Schlie en Sie das System oder das Netzteil nur an eine DC Spannungsauelle an die die Bestimmungen f r Sicherheitskleinspannung SELV in den IEC 60950 basierten Sicherheitsstandards erf llt e DC Ger te m ssen in einem zugangsbeschr nkten ist dass nur geschultes und qualifiziertes Wartungs Bereich installiert werden damit gew hrleistet personal Zugang zu den Ger ten hat Ein zugangsbeschr nkter Bereich kann beispielsweise nur mithilfe eines Spezialwerkzeugs Schloss und Schl ssel oder einer anderen Sicherheitsvorrichtung ge ffnet werden Note Da die Geb udevorschriften in aller Welt unterschiedlich sind empfiehlt Extreme Networks dringend sich bez glich der korrekten Erdung und Spannungsverte
88. ns for building codes and standards Virtually all areas of the United States are regulated by building codes and standards During the early planning stages of installing or modifying your network it is important that you develop athorough understanding of the regulations that pertain to your location and industry Verify that your site meets all environmental and safety requirements Complying with Building and Electrical Codes Building and electrical codes vary depending on your location You must comply with all code specifications when planning your site and installing cable This section lists resources for obtaining additional information For information about major building codes consult the following organization e International Code Council ICC 5203 Leesburg Pike Falls Church Virginia 22041 USA http www iccsafe org htto www sbcci org Table 9 Authorities on Electrical Codes Organization Address Web Site URL National Electrical Code NEC Classification USA only NFPA http www nfpa org Recognized authority on safe electrical wiring Federal state 1 Batterymarch Park and local governments use NEC standards to establish their Quincy Massachusetts own laws ordinances and codes on wiring specifications The 02169 EC classification is published by the National Fire Protection USA Association NFPA Underwriters Laboratory UL USA only UL http www ul com ndependent research and t
89. nual 87 Maintaining the BlackDiamond X8 4 Usea 2 Phillips cross head screwdriver to lock each handle into place When a locking screw is fully tightened the yellow band around the screw head is completely hidden Caution Be careful to avoid over torquing and stripping the screw heads RRRR KRK RH III ptatatet SINN Figure 63 Locking the I O module blank into place Installing I O Module Blanks Without Thumb Levers Some of the older BDX chassis were shipped with module blanks without thumb levers Use the following procedure if you have these older module blanks If you have the newer I O blanks with thumb levers seelnstalling I O Module Blanks on page 86 After you have installed all the I O modules for your system configuration you must install module blanks in all remaining unoccupied slots Caution i All unoccupied slots in a BlackDiamond X8 series switch must have module blanks correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch 1 Check the condition of the EMI gaskets along the front panel edges of the blank and confirm that the gaskets are not damaged BlackDiamond X8 Series Switches Hardware Installation Manual 88 Maintaining the BlackDiamond X8 2 Align the module blank with the card guides for the open slot on the chassis Figure 64 Installing a Module Blank without
90. o hot to touch disengage the laser optic module and allow it to cool before removing it completely When working with laser optic modules always take the precautions listed below to avoid exposure to hazardous radiation A Caution e Never look at the transmit LED laser through a magnifying device while the transmit LED is powered on e Never look directly at a fiber port on the switch or at the ends of a fiber cable when they are powered on e Invisible laser radiation can occur when the connectors are open Avoid direct eye exposure to the beam when optical connections are unplugged e Never alter modify or change an optical device in any way other than suggested in this document Note Extreme Networks optical modules are tested to work in all supported Extreme Networks switches We recommend that all customers use Extreme Networks optical modules in their Extreme Networks switches Extreme Networks assumes no liability for third party optical modules Although Extreme Networks does not block third party optical modules we cannot ensure that all third party optical modules operate properly in all Extreme Networks switches The customer assumes all risks associated with using third party optical modules in Extreme Networks switches GBIC SFP Mini GBIC QSFP XENPAK and XFP Regulatory Compliance Extreme Networks pluggable optical modules and direct attach cables meet the following regulator
91. odule will not work with BDX FMIOT BDXA 40G12X I O Module The BDXA 40G12X O module supports 12 QSFP based 40 gigabit Ethernet ports Each QSFP port can operate as a single 40 gigabit port or as four 10 gigabit ports In 40G port mode the module provides 12 ports if all ports are operating in 10G mode the module provides 48 ports Note e BlackDiamond X8 I O modules are supplied with no pre installed optical modules When the ports are operating in 40 Gbps mode the port numbers increment by 4 For example the first four ports would be numbered from left to right 1 5 9 and 13 Other port numbers are displayed in ExtremeXOS as not available When a port is configured to operate in 10 Gbps mode all four port numbers associated with that physical port are displayed as being available The default mode for the ports is 40 Gbps operation To configure a port for 10 Gbps operation use the command configure ports partition Figure 6 BDXA 40612X I O Module on page 19 shows the front of the module including port and LED locations Figure 6 BDXA 40G12X I O Module 1 QSFP ports 2 LEDs In the default configuration for the BDXA 40G12X module all ports e Are added to the default VLAN as untagged e Inherit the properties of the default VLAN for example protocol type and VLAN ID The BDXA 40G12X module has the following LEDs
92. on Manual 108 Safety Information 1 Wenden Sie sich f r den Austausch eines Produktes an das Wartungspersonal von Extreme Networks Versuchen Sie nicht die Batterie selbst auszuwechseln 2 Bei einer Missachtung wechseln m ssen folg vermeiden dieser Anweisungen und dem Versuch die Batterien eigenm chtig zu ende Richtlinien eingehalten werden um eine m gliche Explosion zu a Tauschen Sie die Batterie nur gegen eine Batterie des gleichen Typs wie vom Hersteller empfohlen aus b Entsorgen Sie die Batterie gem den Empfehlungen des Batterieherstellers LWL Ports und opti sche Sicherheit Folgende Sicherheitswarn eingesetzt werden und en Chassissystem eingebaut Folgende Sicherheitswarn eingesetzt werden und en Chassissystem eingebaut Solche Ger te sind nicht n ung gilt f r alle optischen Ger te die in Extreme Networks Ger ten tweder herausnehmbar sind oder direkt in einem E A Modul oder im sind ung gilt f r alle optischen Ger te die in Extreme Networks Ger ten tweder herausnehmbar sind oder direkt in einem E A Modul oder im sind ur Gigabit Interface Konverter GBICs steckbare Kleinformfaktormodule SFP oder Mini GBICs QSFP Module XENPAK Sendeempf nger und laseroptische XFP Module Warning Laseroptische Module k nnen bei l ngerem Gebrauch sehr hei werden Seien Sie beim A Ausbau eines laseroptischen Moduls aus dem Modul oder der Optionskarte
93. on Manual 90 Maintaining the BlackDiamond X8 7 Locate the DIMM on the management module a a ee Ne A 3 3 5 ut OU Ly Figure 67 Locate the DIMM 1 DIMMS 8 Remove any glue at the top of each latch with your fingers pati oo eek Qn a N L 9 ww aca ooo oo oo oo oo m Figure 68 Glue on the top of the DIMM latch 1 Glue 9 Unlock the DIMM and pull it perpendicularly straight up out of the socket Do not twist or bend the DIMM while you are pulling it out J C g fi fi fi fi J Oo D D 0 D D 0 A D D Oo 0 D 0 0 Qa p i gt N annnnonnnnnnnnnnnnnnnnnnnno mM m m Figure 69 Unlock the latches on the DIMM BlackDiamond X8 Series Switches Hardware Installation Manual 91 Maintaining the BlackDiamond X8 10 Reseat the DIMM into place pushing it gently as far as it will go into the socket there should be a N clicking sound signifying the DIMM is fully seated When it is fully seated the latches will lock back into place 2 a a 0 a a a 0 fil fil 0 fil fil fi
94. ote e The procedure for using terminal emulation software is described in more detail in the documentation supplied with the terminal Logging In for the First Time Log in and manually configure the IP settings 1 Connect a terminal or PC with terminal emulation software to the management module in the switch At the terminal press Enter one or more times until you see the login prompt At the login prompt enter the default user name admin to log on with administrator privileges login admin The system will ask a series of questions about the default management settings which allow all forms of management access for convenience in setting the initial configuration Administrator capabilities allow you to access all switch functions Answer each question based on the level of security needed for the particular management access type Note e For more information about logging in to the switch and configuring switch management access see the ExtremeXOS Concepts Guide At the password prompt press Enter The default user name admin has no password assigned to it When you have successfully logged on to the system the command line prompt displays the system name for example BlackDiamonX8 gt in the prompt Note z2 For more information about how to assign a specific system name see the ExtremeXOS Concepts Guide Type configure vlan default ipaddress 123 45 67 8 255 255 255 0 to assign an IP address and su
95. oward the front of the power supply to fully seat the power supply in the chassis 6 Repeat steps to install other power supplies as required by your system configuration 7 Replace the power supply ventilation cover a Set the lower edge of the cover in place so that the tabs on the edge fit into the matching slots in the chassis frame b Rotate the top of the cover into place against the front of the chassis frame BlackDiamond X8 Series Switches Hardware Installation Manual 51 Installing a BlackDiamond X8 Series Chassis c Align and tighten the retaining screws Important Do not operate the BlackDiamond X8 chassis without the power supply cover in place This cover is required to maintain proper EMI levels for the switch Figure 28 Installing the Power Supply Ventilation Cover Connecting Power Cords Warning Be sure to read Safety Information on page 98 before you begin this procedure A Warning A Do not apply power to the chassis until you have finished installing all modules fan trays and module blanks To apply power and access the chassis see Applying Power and Accessing the Chassis for the First Time on page 65 Use the following procedure to connect the AC power cords and the cord retainer BlackDiamond X8 Series Switches Hardware Installation Manual 5 Installing a BlackDiamond X8 Series Chassis 1 At the back of the chassis connect an AC power cord to the power in
96. port allows you to connect an Ethernet cable directly from your laptop to the management port to view and locally manage the switch configurations This port can also be used to connect the system to a parallel management network for administration e Two USB ports These ports allow you to attach a single external USB 2 0 flash drive for downloading new software or rescuing an image Only one of these ports can be used at any one time Only a USB flash drive that is formatted using the file allocation table FAT file system is recognized on this port Other devices such as a USB external hard drive will not be mounted BlackDiamond X8 Series Switches Hardware Installation Manual 14 BlackDiamond X8 Series Modules and Fans e Console port The RJ 45 serial console port is used to connect a terminal allowing you to perform local management e Auxiliary AUX port For future development Management modules have the following LEDs see Reading Management Module LEDs on page 15 for a description of the LEDs and their meanings e Presence of system errors ERR e System environmental status ENV e Master backup status of the module MSTR e General system status SYS e General fan status FAN e Fabric module status FM ee KHR ee A SR En ie bee Figure 3 BDX MM1 Module a x a 48021 1 LEDs 3 Console port
97. pply e Do not use excessive force when you insert a power supply into the bay BlackDiamond X8 Series Switches Hardware Installation Manual 100 Safety Information Do not attempt to open the power supply enclosure for any reason the power supply does not contain user serviceable parts In the event of failure return the defective power supply to Extreme Networks for repair or replacement Do not put your hand into an open power supply bay when a power supply is not present When you install AC power supplies Do not connect the power supply to an electrical source when the power supply is not installed in the BlackDiamond X8 doing so would expose a hazardous energy and poses a potential shock and fire hazard Plug power supplies only into properly grounded electrical outlets to prevent electrical shock and to comply with international safety standards Use only power cords that are certified for use within the country of use Do not attempt to modify AC power cords Make sure that the voltage and frequency of your power source match the system electrical ratings for the equipment The building and or power source must provide overload protection Use a line conditioner or uninterruptible power supply to protect the system from momentary increases or decreases in electrical power Connect half of the power supplies to one power source Connect the others to a separate independent power source f a power source fails it wil
98. put socket that corresponds to each installed power supply Power input sockets are numbered from 1A to 8B from left to right as you face the chassis back 2A 3A 1A 4A 5B 6B 7B 8B a A AA Figure 29 Numbers for Power Connectors After all the power cords have been connected set the power cord retainer over the power cord connectors and against the back of the chassis 3 Align and tighten the captive retaining screws on the power cord retainer Figure 30 Installing the AC Power Cord Retainer BlackDiamond X8 Series Switches Hardware Installation Manual 53 6 Installing BlackDiamond X8 Series Modules Initial System Installation and Module Installation Order Required Tools Installing Fabric Modules Installing Management Modules Installing I O Modules Applying Power and Accessing the Chassis for the First Time The following sections describe how to install the modules and module blanks into the BlackDiamond X8 chassis Note The BlackDiamond X8 chassis should already be installed before you install any modules into the chassis See Installing a BlackDiamond X8 Series Chassis on page 41 for chassis installation procedures Warning Do not apply power to the chassis until you have finished installing all modules and module blanks Initial System Installation and Module Installation Order After the chassis is installed you can install the modules and module blan
99. r vertical slots in the back behind fan trays for fabric modules FMs e Eight bays in the front for redundant power supplies rear accessible power connections e Five vertical fan trays at the back e Two connectors for an ESD preventive wrist strap e On the front panel between the management modules e On the back panel at the top right corner The figure below shows a BlackDiamond X8 chassis equipped with management modules and O modules Figure 1 Front of the BlackDiamond X8 Chassis 1 Power supply cover 3 Management modules 2 ESD jack 4 O modules The front of the chassis provides access to e Card cage for the management modul
100. s The following sections contain recommendations for planning your connections for your Extreme Networks equipment 0 ecco eee ee e BlackDiamond X8 Series Switches Hardware Installation Manual 5 Preparing Your Site Planning Power Supply Requirements Follow these recommendations when you are planning your connections for your Extreme Networks equipment 1 Place the equipment in an area that accommodates the power consumption and component heat dissipation specifications 2 Be sure that your power supply meets the site DC power or AC power requirements of the network equipment 3 When you connect power to installed equipment do not make this connection through an extension cord or power strip 4 Connect half of the power supplies to one power source Connect the others to a separate independent power source If a power source fails it will affect only the power supplies to which it is connected If all BlackDiamond X8 power supplies are connected to a single power source the entire chassis is vulnerable to a power source failure 5 Inregions that are susceptible to electrical storms we recommend that the AC commercial power should be conditioned and that appropriately sized rated surge arrestor suppression devices be installed utilized For additional information on power supplies see Power Supplies for BlackDiamond X8 Switches on page 115 Turning off and on your unit There is no power switch on
101. s procedure An AC power cord is not included with the chassis You must obtain a power supply cord that meets the requirements listed under Selecting Power Supply Cords on page 101 1 Remove the power supply ventilation cover a Loosen the retaining screws at the top corners of the cover panel b Pull outward on the retaining screws to tilt the cover panel away from the front of the chassis BlackDiamond X8 Series Switches Hardware Installation Manual 49 Installing a BlackDiamond X8 Series Chassis c Lift the cover panel away from the chassis Figure 25 Removing the Power Supply Ventilation Cover 2 Identify the power supply bay where you will install the power supply Power supply bays are numbered from 1A to 8B To establish an N N redundant power configuration install power supplies in both the upper and lower rows 1A 2A 3A 4A 1 A oo SSS tat SS 5B 6B 7B 8B Figure 26 Power Supply Bay Numbering on the Chassis 3 Onthe front of the power supply push the release button to unlatch the insertion ejector lever BlackDiamond X8 Series Switches Hardware Installation Manual 50 Installing a BlackDiamond X8 Series Chassis 4 Slide the power supply into the chassis until the lever starts to engage Figure 27 Installing a Power Supply 5 Rotate the lever t
102. se notes and entitled software from the eSupport web pages at http www extremenetworks com g0 eSupport Note You must have an active support agreement or a product registered to you in order to 2 receive an eSupport login and access to Extreme Networks software release notes To request an eSupport user name and password select the Request Web Login link on the eSupport home page For instructions on accessing and downloading software and software release notes see the Technical Assistance Center User Guide at www extremenetworks com go tacuserguide You can see complete information about all of our services online at www extremenetworks com solutions service solutions aspx BlackDiamond X8 Series Switches Hardware Installation Manual 7 1 BlackDiamond X8 Series Switches BlackDiamond X8 Overview BlackDiamond X8 Chassis Features Management Module Ports Overview The following sections provide an oveview of the BlackDiamond X8 Series Switches Switch Overview BlackDiamond X8 Chassis Features on page 8 Management Module Ports Overview on page 11 BlackDiamond X8 Overview The BlackDiamond X8 series switches are chassis based switches designed for virtualized data centers and high performance compute cluster installations They provide high density line rate 10 40 GbE ports For more information about configuring a BlackDiamond switch see the ExtremeXOS Concepts Guide and the ExtremeXOS Command Reference Guide
103. ssign a unique identification number to each equipment rack Identify all equipment locations by labeling the front panel of your Extreme Networks equipment and other hardware 5 Keep accurate and current cable identification records 6 Post records near each equipment rack For each cable drop include information about the cable source destination and jumper location Determining Cable Distances Building and electrical codes vary depending on your location The following tables show cable media types and maximum distances that support reliable transmission in accordance with international standards except where noted Table 12 Extreme Networks Direct Attach Cables on page 35 lists the Extreme Networks direct attach cables Table 10 Fiber Media Types and Maximum Cable Distances Standard Media Type Mhz Km Maximum Distance Rating 1000BASE SX 50 125 um multimode fiber 400 500 meters SSO OTT OPCA WINUGW 50 125 um multimode fiber 500 550 meters 62 5 125 um multimode fiber 160 220 meters 62 5 125 um multimode fiber 200 275 meters 1000BASE LX 50 125 um multimode fiber 400 550 meters Noo n optice Ancon 50 125 um multimode fiber 500 550 meters 62 5 125 um multimode fiber 500 550 meters 10 125 um single mode fiber 5km 10 125 um single mode fiber 10 km meters 1000BASE ZX 10 125 um single mode fiber 80 km 1550 nm optical window 100BASE LX100 10 125 um single mode fiber 100 km
104. sult an electrical contractor for commercial building and wiring specifications 1 Be sure that your system is readily accessible for installation and service See Rack Specifications and Recommendations on page 31 for information Use appropriate AC or DC power power distribution and grounding for your specific installation 3 Use a vinyl floor covering in wiring closets or other indoor equipment locations Concrete floors accumulate dust and carpets can cause static electricity 4 Prevent unauthorized access to equipment locations by providing door locks Install the equipment in a secured enclosed and restricted access location ensuring that only qualified service personnel have access to the equipment 5 Provide adequate overhead lighting for easy maintenance 6 Besure that each equipment location has a suitable ground All equipment racks and equipment installed in the closet should be grounded 7 Besure that all system environmental requirements are met such as ambient temperature and humidity Controlling Temperature It is important to keep installed equipment within the thermal operating specifications for optimum performance and safety Install the equipment only in a temperature and humidity controlled indoor area that is free of airborne materials Too much humidity can cause a fire Too little humidity can produce electrical shock and fire Note As with all electrical equipment Extreme Networks product lifet
105. t module allow you to attach a single USB 2 0 flash drive Only a USB flash drive that is formatted using the file allocation table FAT file system is recognized on these ports Other devices such as a USB external hard drive will not be mounted For more information including a diagram showing the location of the management module ports see Features of the Management Module on page 14 BlackDiamond X8 Series Switches Hardware Installation Manual 11 2 BlackDiamond X8 Series Modules and Fans Module Overview Understanding Management Modules Understanding I O Modules Understanding Fabric Modules Understanding Fan Trays The following sections provide information on the BlackDiamond X8 Series modules and fans e Module Overview on page 12 e Understanding Management Modules on page 13 e Understanding I O Modules on page 16 e Understanding Fabric Modules on page 21 e Understanding Fan Trays on page 22 Module Overview Modules for the switch include management modules I O modules and switch fabric modules Each module for the switch consists of a printed circuit board mounted on a metal panel The module carrier also includes ejector injector levers and captive retaining screws on the module front panel Table 3 Modules Available for the BlackDiamond X8 Series Switch Module Type Short Description Long Description Manufacturing No SKU Management module BDX MMI Management Module 1 for 900848 10 BlackDiamond
106. teria C 2004 108 EC EMC Directive International CISPR 22 2005 A1 2005 Class A International Emissions CISPR 24 1997_A1 2001 A2 2002 International Immunity VCCI 2010 04 Class A Japan ACMA AS NZS CISPR22 2009 Australia KCC Mark KN22 KN24 Korea BSMI CNS 13438 1997 Class A Taiwan BSMI CNS 14336 1 2010 Safety Taiwan oO lt mas m Mm MM 3 Table 16 Telecommunications EN ETSI 300 386 v1 4 1 2008 04 Emissions amp Immunity EN ETSI 300 019 2 1 v2 1 2 Class 1 2 Storage EN ETSI 300 019 2 2 v2 1 2 Class 2 3 Transportation EN ETSI 300 019 2 3 v2 1 2 Class 3 le Operational EN ETSI 300 753 1997 10 Acoustic Noise BlackDiamond X8 Series Switches Hardware Installation Manual 112 Technical Specifications Table 17 IEEE 802 3 Media Access Standards Note These standards are IEEE 802 3 IOBASE T management port only module specific and may not IEEE 802 5u I100BASE TX I00BASE FX management port only apply to every module in the IEEE 802 32 JOOOBASE X series IEEE 802 3ab IOOOBASE T IEEE 802 3ac VLAN Tag IEEE 802 3ad Link Aggregation IEEE 802 3ae IOGBASE X Table 18 Environmental Data Operating conditions Operating temperature range 0 C to 40 C 32 F to 104 F Operating humidity 10 to 93 relative humidity non condensing Operational shock 30 m s 3 g 11 ms 60 shocks Operational sine vibration 5 to 100 to 5 Hz
107. the chassis Warning a For systems using an AC power supply unplug the AC power cords from the back of the chassis to disconnect the power to the chassis AC Power Cord Requirements AC power input cords are not included with BlackDiamond X8 power supplies You can purchase AC power cords for use in the US and Canada from Extreme Networks or from your local supplier Make sure that the power cord you use is certified for the country of end use and suitable for the device Check your local electrical codes and regulatory agencies for power cable requirements The power cord must meet the requirements listed in Selecting Power Supply Cords on page 101 Note e Make sure that each AC PSU is supplied by independently fused power circuits BlackDiamond X8 Series Switches Hardware Installation Manual 38 Preparing Your Site Uninterruptible Power Supply Requirements An uninterruptible power supply UPS is a device that sits between a power supply such as a wall outlet and a device such as a switch to prevent outages sags surges and bad harmonics from adversely affecting the performance of the device A UPS traditionally can perform the following functions e Absorb relatively small power surges e Smooth out noisy power sources e Continue to provide power to equipment during line sags e Provide power for some time after a blackout has occurred In addition some UPS or UPS plus software combinations provide
108. the metal end to the receptacle between the management module slots 3 If necessary remove the cover from the unoccupied slot Remove the module from the antistatic packaging Caution a To prevent ESD damage hold the module by the metal rail and front panel only Never touch the components on the PCB or the pins on any of the connectors 5 Verify that the injector ejector handle is in the open position Keep the injector ejector handle in the open position as you slide the module into the chassis slot 6 Carefully slide the module into the slot starting with slot A until the injector ejector handle engages the edge of the chassis and begins to rotate toward the module BlackDiamond X8 Series Switches Hardware Installation Manual 58 Installing BlackDiamond X8 Series Modules 7 Use the lever to fully seat the module internal connectors Figure 35 Seating the Management Module 8 Usea 2 Phillips screwdriver to lock the handle into place When the locking screw is fully tightened the yellow band around the screw head is completely hidden Caution Be careful to avoid over torquing and stripping the screw head Figure 36 Locking the Module into Place BlackDiamond X8 Series Switches Hardware Installation Manual 59 Installing BlackDiamond X8 Series Modules 9 Install module blanks in all remaining unoccupied slots Caution a All unoccupied management module slots i
109. ttern that is identified in IEC Standard 297 Ensure the rack has designated earth grounding connections typically on the base BlackDiamond X8 Series Switches Hardware Installation Manual 31 Preparing Your Site e Ensure the rack must meet earthquake safety requirements equal to that of the installed chassis e Ensure the mounting holes are flush with the rails to accommodate the chassis e Ensure the rack supports approximately 1260 pounds 572 kg Using Protective Grounding for the Rack Use a rack grounding kit and a ground conductor that is carried back to earth or to another suitable building ground All Extreme Networks switches are designed with mounting brackets that provide solid metal to metal connection to the rack If you do not use equipment racks you can attach wiring terminals directly to the mounting brackets for appropriate grounding Extreme Networks switches have grounding terminals that are mounted on the back of the chassis Note e Because building codes vary worldwide We strongly recommend that you consult an electrical contractor to ensure proper equipment grounding for your specific installation At a minimum follow these guidelines to ground equipment racks to the earth ground 1 CAD weld appropriate wire terminals to building l beams or earth ground rods 2 Use the appropriate chassis grounding wire for your system the correct size depends on the available input current to the power s
110. u erst Ay vorsichtig Wenn das laseroptische Modul zum Anfassen zu hei ist trennen Sie das laseroptische Modul und lassen Sie es abk hlen ehe Sie es komplett ausbauen Ergreifen Sie be im Arbeiten mit laseroptischen Modulen die nachfolgenden Vorsichtsma nahmen um eine Aussetzung gegen ber gef hrlicher Strahlung zu vermeiden e Blicken Sie auf keinen Sendediode aktiv ist e Blicken Sie auf keinen Kabels Fall durch ein Vergr erungsglas in die Sendediode den Laser solange die Fall in den LWL Port am Switch oder auf die Stirnfl chen eines aktiven LWL e Bei offenen Anschl ssen kann unsichtbare Laserstrahlung abgegeben werden Vermeiden Sie eine direkte Aussetzung de Stecker sind r Augen gegen ber dem Strahl wenn die optischen Anschl sse offen ohne e Optische Ger te d rfen auf keine andere Weise als in diesem Dokument empfohlen ver ndert modifiziert oder umge baut werden Konformit t von GBIC SFP Mini GBIC QSFP XENPAK und XFP Steckbare optische Modul gesetzliche Vorschriften e von Extreme Networks und direkt angeschlossene Kabel erf llen folgende e Laserprodukt der Klasse 1 oder Klasse IM e EN60825 1 2007 2 Au sgabe oder sp ter Europ ische Norm e FCC 21CFR Kapitel 1 Paragraph J in bereinstimmung mit FDA und CDRH Bestimmungen BlackDiamond X8 Series Switches Hardware Installation Manual 109 Safety Information e Anwendung des CE Zeichens gem der EMV Ri
111. unding the chassis is optional it is recommended to do so You must provide the following materials to ground the chassis e Two 10 24 screws e One copper standard barrel 2 hole compression grounding lug with 0 63 inch hole spacing type LDC equivalent to Panduit part number LCD4 14A L or Thomas amp Betts part number LCN4 14 e 14 AWG stranded copper wire The rear panel of the chassis provides a grounding pad with threaded holes for attaching a ground cable BlackDiamond X8 Series Switches Hardware Installation Manual 48 Installing a BlackDiamond X8 Series Chassis 1 Identify the grounding pad on the back of the chassis 0p BEBBEBER _ Figure 24 Grounding Pad on the Chassis 1 Grounding pad Strip 0 5 inch 1 2 cm of insulation from the stranded copper wire cable Insert the stripped wire into the cable lug Crimp the lug securely onto the cable Insert the screws through the lug and into the grounding pad on the back of the chassis Connect the other end of the wire to aknown reliable earth ground point at your site OUA UNN After the chassis is grounded install two or more power supplies Installing Power Supplies You need the following tools and equipment to install an AC power supply e 2 Phillips screwdriver e AC power cord rated for 100 120 200 240 VAC Warning Be sure to read Safety Information on page 98 before you begin thi
112. upply For AC systems using a 20A breaker per PSU the chassis ground can be as small as 14 AWG The power cable ground should be the same size as the primary Note For complete details on power supplies and power supply cords refer to Power Supplies and to Selecting Power Supply Cords on page 101 Drill and tap wire terminals to equipment racks 3 Position the earth ground as close to the equipment rack as possible to maintain the shortest wiring distance possible 4 Usea ground impedance tester or micro ohm meter to test the quality of earth ground connection at the chassis This will ensure good grounding between the chassis rack and earth ground Meeting Space Requirements for the Rack The rack must have enough space around it for servicing Provide enough space in front of and behind the switch so that you can service it easily a Allow a minimum of 48 inches 122 cm in front of the rack and 24 inches 61 cm behind the rack b When using a relay two post rack provide a minimum of 24 inches 61 cm of space behind the mounted equipment c Extra room on each side is optional BlackDiamond X8 Series Switches Hardware Installation Manual 32 Preparing Your Site Securing the Rack 1 Attach the rack to the floor with 3 8 inch 9 5 mm lag screws or equivalent hardware The floor under the rack should be level within 3 16 inch 5 mm Use a floor leveling cement compound if necessary or bolt the racks to the f
113. ure 57 Locking the Module into Place Installing a Management Module Blank Install a blank management module in every unoccupied management slot If a management module is not installed in a slot you must install a blank cover over the slot to maintain proper EMI levels and ventilation to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch 1 2 Set the blank in place over the open slot Align and tighten the captive retaining screws Removing an I O Module You need the following tools and equipment to remove an O module ESD preventive wrist strap 2 Phillips cross head screwdriver Module blank panel if you are not replacing the module Attach the ESD preventive wrist strap to your bare wrist If it is not already connected connect the metal end to the receptacle between the management module slots Disconnect network cables from the front of the module BlackDiamond X8 Series Switches Hardware Installation Manual 82 Maintaining the BlackDiamond X8 A On each injector ejector lever turn the captive screw counter clockwise until the yellow band around the screw head of is completely visible RRR LRT LAAVAA Figure 58 Unlocking a Module 5 Squeeze the release latch on each injector ejector handle and rotate both handles outward to disconnect the internal module connectors Figure 59 Removing an I O Module
114. use electrostatic generation such as synthetic resins from the equipment location Check the appropriateness of floor mats and flooring Connect metal chassis conduit and other metals to ground using dedicated copper grounding lines Use electrostatically safe equipment a Ifyou are working with pluggable interface modules wear an ESD preventive device such as a wrist strap and connect the metal end to a grounded equipment rack or other source of ground E Figure 11 Using an ESD preventive Wrist Strap RRRERRE REH Rack Specifications and Recommendations Racks should conform to conventional standards In the United States use EIA Standard RS 310C Racks Panels and Associated Equipment In countries other than the United States use IEC Standard 297 In addition verify that your rack meets the basic mechanical space and earthquake requirements that are described in this section Mechanical Recommendations for the Rack Use equipment racks that meet the following mechanical recommendations Use an open style 19 inch rack to facilitate easy maintenance and to provide proper ventilation Use a rack made of steel or aluminum Use the universal mounting rail hole pa
115. witches Hardware Installation Manual 115 Technical Specifications Table 24 RJ 45 Console Port on BlackDiamond X8 Switch Function Pin Number Direction CTS clear to send 1 In DTR data carrier detect 2 Out TXD transmit data 3 Out GND ground 4 GND ground 5 _ RXD receive data 6 In DSR data set ready 7 In RTS request to send 8 Out The following table shows the pinouts for an RJ 45 to DB 9 adapter Table 25 Pinouts for an RJ 45 to DB 9 Adapter Signal RJ 45 Pin DB 9 Pin CTS clear to send 1 DTR data carrier detect 2 6 TXD transmit data 3 2 GND ground 4 5 GND ground 5 5 RXD receive data 6 5 DSR data set ready 7 4 RTS request to send 8 7 Figure 78 Null modem Cable Pinouts on page 117 shows the pinouts for a 9 pin to 25 pin RS 232 null modem cable BlackDiamond X8 Series Switches Hardware Installation Manual 116 Technical Specifications Switch PC Terminal Cable connector 9 pin female Cable connector 25 pin male female Screen Shell _ 1 Screen TxD 3 le 3 RxD RxD 2 Ile 2 TxD Ground 5 7 Ground RTS 7 4 RTS CTS 8 20 DTR DSR 6 5 CTS DCD 1 6 DSR DTR 4 o 8 DCD Figure 78 Null modem Cable Pinouts Figure 79 PC AT Serial Null modem Cable Pinouts on page 117 shows the pinouts for a 9 pin to 9 pin
116. y requirements e Class 1or Class IM Laser Product e EN60825 1 2007 2nd Ed or later European standard e FCC 21 CFR Chapter 1 Subchapter J in accordance with FDA amp CDRH requirements e Application of CE Mark in accordance with 2004 108 EEC EMC Directive the 2006 95 EC Low Voltage Directives e UL and or CSA registered component for North America e 47 CFR Part 15 Class A when installed into Extreme products BlackDiamond X8 Series Switches Hardware Installation Manual 103 Safety Information Sicherheitshinweise Lesen Sie die folgenden Sicherheitshinweise aufmerksam durch ehe Sie Extreme Networks Produkte installieren Eine Missachtung dieser Sicherheitshinweise kann zu Verletzungen oder zu einer Besch digung des r Ger te s f hren Extreme Networks Ger te und deren Komponenten d rfen nur durch geschulte und qualifizierte Wartungstechniker wie in IEC 60950 1 und AS NZS 3260 definiert installiert ausgetauscht oder gewartet werden Dieses qualifizierte Personal muss den Inhalt aller zugeh rigen nstallationsanleitungen kennen sowie ber die technische Ausbildung und Erfahrung verf gen um die Gefahren die mit der Ausf hrung einer Aufgabe assoziiert sind zu kennen und zu wissen wie sie diese Gefahren f r sich selbst und Dritte minimieren k nnen In den USA muss das System gem dem US National Electrical Code NEC installiert werden berlegungen vor der Installation B
117. y of 10 Terabits per second and BDXA FM20T fabric modules provide 20 Terabits per second A switch fabric composed of BDXA FMIOT modules will provide full line rate for the BDXA 10G48X BDXA 10G48T and BDXA 40G12X I O modules For the BDXA 40G24X O module a BDXA FM20T switch fabric is required for full line rate on all ports The BDXA 40G24X I O module will not operate with a switch fabric composed of BDXA FMIOT modules BlackDiamond X8 Series Switches Hardware Installation Manual 21 BlackDiamond X8 Series Modules and Fans Allthe fabric modules in a switch must be the same type you cannot combine BDXA FMIOT modules and BDXA FM20T modules Status LEDs for each fabric module are on the fan tray that is in front of that fabric module The status LEDs for the fabric module are labeled Diag and Stat The following table describes the meanings of the fabric module LEDs Table 6 LEDs for the BlackDiamond X8 Series Fabric Modules Label Function Color State Meaning DIAG Module diagnostics Amber blinking Diagnostic tests are in progress Amber steady A diagnostic failure has occurred Off ormal operation STAT Module status Green blinking ormal operation Amber blinking Configuration error code version error or other severe module error Amber steady The module is present but not receiving power Off The module is not present

BlackDiamond X8 Series Switches Hardware

Contents

Download Pdf Manuals

Related Search

Related Contents