ECO.32 Magnetic Drilling Machine
Contents
1. at all times when using magnetic drilling machines Improper use and carelessness increase the risk of accidents This is for your own safety Should you have any doubts about the use of this machine please contact your supplier 2 Safety 10 11 12 13 14 15 During any work on non horizontal components the machine must always be secured with the supplied safety chain The magnetic drilling machine may only be used on a flat and clean foundation If the machine or the lead show signs of damage the magnetic drilling machine must be switched off immediately Wearing safety glasses hearing protection and protective clothing is necessary Do not wear any loose clothing or jewellery that may get entangled in the moving parts of the magnetic drilling machine Use only accessories or parts that are recommended by Euroboor During drill operations the hole cutter must be cooled and lubricated with good quality cutting or lubrication oil The motor must be switched off when tightening the machine with the safety chain When changing a hole cutter the magnetic drilling machine must be disconnected from power supply Clean the area around the machine regularly Keep the bottom of the magnet and keep it clean and dry Regularly inspect whether all screws nuts and bolts are tight Remove the burr or slug from the hole cutter after each hole Caution the part may be hot Before using the machine ma2. cutters with cutting depth 75 mm increasing by 1 mm HCX 20mm 50mm Hole cutters with cutting depth 100 mm increasing by 1 mm Also available in inch sizes HCS 7 16 5 Hole cutters with cutting depth 30 mm increasing by 1 16 HCL 7 16 5 Hole cutters with cutting depth 55 mm increasing by 1 16 HCY 3 4 21 16 Hole cutters with cutting depth 75 mm increasing by 1 16 HCX 3 4 21 16 Hole cutters with cutting depth 100 mm increasing by 1 16 Euroboor Cobalt Series For processing steel stainless steel and other high quality steel alloy types IBS 12 mm 130 mm Hole cutters with cutting depth 30 mm increasing by 1 mm IBL 13 mm 130 mm Hole cutters with cutting depth 55 mm increasing by 1 mm Euroboor TCT Series Tungsten Carbide Tipped Cutters with hard metal teeth HMS 14mm 50mm Hole cutters with cutting depth 35 mm increasing by 1 mm HML 14mm 130 mm Hole cutters with cutting depth 50 mm increasing by 1 mm Euroboor TRC Series With hard metal teeth For drilling holes in rails TRCS 190 19 mm Hole cutter with cutting depth 35 mm TRCS 300 30 mm Hole cutter with cutting depth 35 mm TRCS 330 33 mm Hole cutter with cutting depth 35 mm NOTE Hole cutters 12mm 60mm have a 19 05 mm Weldon shank Hole cutters 61mm 130mm have a 31 75 mm Weldon shank Cooling Lubrication 1 Holes for cooling and lubrication oil 2 Fixing screws of spindle Euroboor recommends the use of cooling and lubrication agents Not only
3. do these assist in drilling but they will also lengthen the lifespan of your tools One of the advantages of the use of hole cutters is that cooling and lubrication agent scan be supplied from the inside so that the agents end up in the right place All magnetic drilling machines from Euroboor can be equipped with a automatic cooling system which provides a guaranteed supply of the cooling and lubrication agents from the inside If your machine is not be equipped with an automatic coolant system it will still be possible to cool from the inside Use the holes in the spindle number 1 in picture for this purpose by squirting the cooling and lubrication agent into the drill spindle through them NOTE For vertical or upside down processing Euroboor recommends the use of a drilling compound or paste like IBP50 2 4 Tool Assembly Hole Cutter Assembly Pilot Pin Center hole in shank of Hole Cutter Shank of Hole Cutter Groove or flatted surface for oil pass Flat surface for fixing Hole Cutter e 1 Te u AeA wW N e Clean the inner wall and the shaft of the Hole Cutter to ensure proper oil supply First insert the Pilot Pin into the center hole of the Shank After that you can slide the Hole Cutter assembly into the spindle of your Magnetic Drilling Machine After sliding the 5 3 Hole Cutter Assembly into type spindle make sure the two flat surfaces number 5 in picture are located exactly in front of
4. FOR PROFESSIONALS BY PROFESSIONALS USER MANUAL TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL ECO 32 Magnetic Drilling Machine SERIAL NO DATE OF PURCHASE 1 Table of Contents 1 Table Of CORIERIS ua zona oO ROG AWCE Hate A OWA R oai a ia page 1 SIEM audi WG O RE wia o bO EEE E page 2 Before USE aaa ida deann aaa Waal a w dA ia vas Ara aa page 3 3 Items Included in Delivery uu cee ses aaa aaa asa aaa aaa ana ana aaa anawa aaa zana aaa iay aaa wz aazazaaeaaainai page 4 The Hole Cutter Hole Cutter Selection 2 lt 6 scssesdvcsivesecsvessvetnesnnestivevadedesetiesecdecsesdensevasvadsdesasdheedduesteeees ose page 5 Cooling AIS CATON GEKKO WGA GAGA KACA page 6 4 Tool Assembly Hole Cutter ASSem DIV kesene aa e s OO WA eae page 6 Drill Chuck Assembly aaa ai Od AWR ad a eset page 7 Installation of 13mm Chuck by using Adaptor IBK 14 e aaeaee ua anna aaa ee canaaaae page 7 Installation of 13mm Chuck directly on the motor unit sssssa saa a aa aaaannannaa page 7 4 The Magnetic Drilling Machine The Magnetic Base wes kawowa page 7 The Control Panel zaa di O A Eaa page 8 DAING e ROA O ROA O ORT ALTO CLA page 9 Maintenance waza ao a Woda tdi edo W o b a page 10 Spareparts 8 Exploded VIEWaweccacionakaG O AUR EEE page 11 Read these directions and safety instructions completely and attentively and carefully follow these recommendations All safety measures must be observed
5. ce Always use the safety chain included Drilling above your head is extremely dangerous and is not recommended For the use of magnetic drilling machines on pipes not flat or non magnetic materials we refer to our brochure or our website www euroboor com where several vacuum tightening systems and pipe clamping systems are mentioned The Control Panel The control panel on your magnetic drilling machine is designed for maximum operating facility and safety 1 The Magnet Switch This switch is used to switch the main power and also the magnet On and Off This switch is included on every Euroboor magnetic drilling machine 2 The On Off Switch This switch is used to switch the motor unit On and Off and is included on every Euroboor Magnetic Drilling Machine 2 3 The Fuse holder with Fuse This Fuse holder is included on every Euroboor Magnetic Drilling Machine and holds the fuse type 5x20 F2A 4 The Magnet LED Indicator This LED indicator shows the generated magnetic force Drilling Now that you have read the explanatory information and safety recommendations above you are ready to actually start drilling Follow these 10 steps for best drilling result 1 10 Use the tip of the pilot pin to determine the center of the hole to be drilled Turn the magnet on and verify that the drill is in the right position and that the machine is pushed tight against the work piece If your machine is equipped with a au
6. g nut motor cable Coupling nut main cable Main Cable Screw washer nut Rear plate Panel screw Front plate Sensor LED cable 35 36 37 38 39 40 41 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 Article 020 0006 020 0016 020 0017 020 0011 020 0001 020 0002 020 0037 032 0101 032 0102 032 0136 032 0141 032 0116 032 0156 032 0121 032 0191 032 0126 032 0221 032 0171 032 0186 032 0226 032 0201 032 0231 032 0131 032 0146 032 0151 032 0152 032 0181 032 0182 032 0111 032 0241 032 0206 032 0216 032 0106 032 0196 032 0161 032 0176 032 0166 032 0236 032 0236 Description On Off switch Fuse Holder Fuse F2A Magnet Switch Control Unit 220v Control Unit 110v Cable clamp Motor unit 220v Motor unit 110v Screw for spring Spring Screw BK4 2x13 Screw BK3 9x60 Adaptor ring 22x0 5 Adaptor ring 17x0 1 Bearing closed 8x22x7 Bearing 8x22x7 Bearing 12x28x8 Spindle Gear First Gear Spindle Drive shaft Axle Adaptor ring Cap Carbon brush set Field 220v Field 110v Armature 220v Armature 110v End Cover Housing Gear Casing Screw BK4 8x38 Screw BK4 8x50 Bearing 17x35x10 Baffle Circlip 471 10 Circlip 472 28 Inner Gear Plate Casing Pin 11 BH je e z b i i ia F oooh TH L CE ODA w ww Iw fw w a iS S u w ZANE az Important notice Because of minor changes to o
7. in The yellow green wire in the lead is the earth wire Never connect this to a pole under voltage All Euroboor magnetic drilling machines are manufactured to use with AC current and not suitable to work on DC current Make sure the magnetic drilling machine is connected to a stable power supply Euroboor do not recommend the use of a generator or other mobile power supply for power supply Euroboor does not recommend the use of extension cables If there is no other way use good quality cables and keep extension cables as short as possible Be aware that long power leads can cause less current 3 Items Included in Delivery Magnetic Drilling Machine YES Pilot Pin NO Carrying Case YES Morse Taper NO Drill Chuck 13mm NO Morse Taper Ejector Pin NO Tap Collets M10 M12 M14 M16 NO Manual YES Allen Key 2 5 YES Safety Chain YES Allen Key 3 NO Drilling Oil YES Allen Key 4 YES Safety Ear Protection YES Allen Key 5 YES Safety Glasses YES Wrench 8 YES Safety Gloves YES 4 The Hole Cutter Hole Cutter selection There are many different types of steel It is not possible to drill all these types of steel with 1 type of cutter Euroboor recommended the following Euroboor HSS Series For drilling holes in general 37 52 steel and aluminium HCS 12 mm 130 mm Hole cutters with cutting depth 30 mm increasing by 1 mm HCL 12 mm 130 mm Hole cutters with cutting depth 55 mm increasing by 1 mm HCY 20mm 50mm Hole
8. ir or other maintenance Euroboor machines are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts ie part numbers and or design may be changed without prior notice Also due to Euroboor s continuing program of research and development the specifications of machines are subject to change without prior notice 10 6 Spare parts amp Exploded view of ECO 32 u RB w N Be 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Article 020 0056 020 0106 020 0111 020 0096 020 0091 020 0098 020 0052 020 0051 020 0201 032 0011 032 0016 020 0156 032 0026 020 0146 032 0041 020 0142 020 0116 020 0116Q 020 0121 020 0131 020 0145 020 0136 020 0086 020 0084 4 020 0084 6 020 0061 020 0330 020 0077 020 0081 020 0066 020 0046 020 0041 020 0031 020 0036 020 0182 PP RSEU 020 0101 PP 32EU 020 0206 Description Frame Screw SSM6x16 Washer M6 Setting Nut Setting Screw Setting set 6x No 4 5 Magnet H 42mm Magnet 2004 H 48mm Sensor Slide Rack Screw SSM6x20 Motor holder Screw SSM6x25 Top fixing plate 120mm Steady Spindle Spindle Quick connect Spring set spindle Circlip Auto coolant Ring Fixing Screw M8x8 Brass rail set stick Pressing Strip 4 holes Pressing Strip 6 holes Capstan Hub assembly Power Assist small End Plate End Screw Arm for Capstan Motor cable Couplin
9. ke sure it is connected to the correct voltage and that all grips and parts are tightly attached When using the drill on non horizontal surfaces you must use a drilling compound or cutting paste Do not use oil because the oil can drip into the motor unit When using this machine you MUST wear ear and eye protection Euroboor has included these articles as standard accessories for your own safety Do NOT touch the drill when it is running Always follow the recommendations for personal protection when using this tool Before use Euroboor magnet drilling machines are specially designed for drilling holes is steel possibly expanded by the possibility of tapping reaming countersinking depending on model Euroboor magnetic drilling machines may not be adapted and or used for applications other than those they were designed for including driving other machines Make sure that you can oversee the entire work areas from where you are operating this machine Use barriers to keep others away Do not use the machine in places subject to hazard of explosion electrical tools produce sparks which may ignite flammable materials or gasses To prevent electrical shocks do not use the machine in moist or wet conditions or environments Always operate this tool using both hands Make sure the work piece is always clamped down safety This magnetic drilling machine is equipped with a lead and plug approved for the country or region it is to be used
10. ll Chuck with internal 1 2 x20 UNF tread on the extending shaft of the motor unit IMPORTANT When reinstalling the spindle and the triangular guide steady you must ensure that the triangular guide steady does not cause any friction or resistance to the spindle as it turns 4 The Magnetic Drilling Machine The Magnetic base Material of minimum 10mm thickness is required for the magnet to work the best The attachment force generated by the magnet depends on various factors Thickness of the material the magnet is placed on Paint or coating of the material the magnet is placed on Metal chips oil or other dirt under the magnet If the LED indicator see chapter 4 3 2 lights up GREEN the magnet is generating sufficient attachment force If the LED indicator lights up RED the magnet may not generating sufficient attachment force We would like to point out that this is only an indication and not a certainly that the magnet will not release from the material Euroboor accepts no liability ensuring from the magnet indicator not functioning or functioning poorly Make sure that the magnet attaches tightly to the work piece before turning on the motor unit of the magnetic drilling machine Euroboor magnets have 2 coils make sure that both coils are in contact with the material Do not connect any other machines to the electrical outlet the magnetic drilling machine is plugged into as it may result in the loss of magnetic for
11. ne with moving parts your Euroboor magnetic drilling machine also needs regular maintenance service A few recommendations follow Clean all dirt dust metal chips and burrs of your magnetic drilling machine Regularly check the carbon brushes for wear Replace any defective parts immediately This prevents properly function parts from being damaged Adjust your guide regularly and make sure it is clean and greased This prevents any movement from being created and the spindle triangular guide steady and guide parts from excessive wear or damage The guide can be adjusted by loosening the setting nut 7 on spare part drawing with included wrench 8 tightening the setting screws 5 on spare part drawing with included Allen key 2 5 and tightening the setting nut 7 again with included wrench 8 The adjustment is done well when the motor unit can be turned to every possible position without falling down by its own weight Check the grease in the gearbox regularly and replace it if necessary We recommend you to store your machine on its side regularly so that the gear box grease can run back to where the gears are This is very important when you have used your machine non horizontal or upside down Repair modification and inspection of Euroboor Magnetic drilling machines must be done by a Euroboor authorized dealer The parts list will be helpful if presented with the machine to the Euroboor dealer for service when requesting repa
12. the two fixing screws of your spindle see number 2 in picture of chapter 4 4 2 Tighten them both subsequently with the included 4mm Allen Key Drill Chuck Assembly The option of making our machines suitable for the use of standard spiral drills and other tools by using a cylindrical shaft is an important characteristic of Euroboor magnetic drilling machines Please see the technical data for maximum capacity Installation of 13mm Chuck by using adapter IBK 14 The IBK 14 is a adaptor from 1 2 x20 UNF to 3 4 Weldon Attach a Drill Chuck like Euroboor IBK 13 with internal 1 2 x20 UNF on the IBK 14 adaptor To attach the assembly into your Spindle follow the instructions with exception of the Pilot Pin for installation of a Hole Cutter Adaptor IBK 14 can be used on most machines in our program Installation of 13mm Chuck directly on the motor unit For the ECO 32 ECO 32T ECO 40 and IBM 30 2 magnetic drilling machines it is possible to install a drill Chuck directly to the shaft extending from the motor unit For ECO 32T First remove the two Allen screws on top of the spindle with the included Allen key no 3 Remove the Spindle by using wrench 18 and 20 Fix the extending motor shaft with wrench 18 and turn the spindle with wrench 20 anti clockwise Take the spindle of the shaft and out of the triangular guide Steady Remove all the Allen screws below the triangular guide by using the included Allen Key no 5 Now can install the Dri
13. to coolant system put open the valve to release the oil If your machine does not have a auto coolant system fill the holes of the spindle with oil Turn the motor on at the highest setting and allow it to run at full speed Turn the arms to start drilling Apply only a slight pressure when the hole cutter touch the metal Do not push the hole cutter with force into the metal Apply a regular pressure while drilling The drilling performance does not improve by putting more pressure on the tool Too much pressure will overload the motor and your hole cutter will be worn sooner Let the cutter do the job and give it time to cut the metal Adjust the oil supply when necessary if your drill does not have a auto coolant system stop drilling regularly refill the holes of the spindle and continue drilling Apply less pressure when the drill cuts through the material Turn the arms to put the motor in highest position and turn off the motor unit Remove the burr metal chips and clean the cutter and surface without getting injuries Caution The metal piece drilled out can be sharp and very hot II IMPORTANT When using your magnetic drilling machine non horizontal or upside down be aware that no oil drilling compound or metal chips can fall into the motor unit Euroboor accepts no responsibility for damage done to your machine by such action under coverage of the warranty 5 Maintenance Just as every magnetic drilling machi
14. ur machines it is recommended to provide the framenumber of your machine when ordering spareparts This number can be found on front of machine at magnetic base and frame When you have any doubt when ordering spareparts please contact your supplier before ordering 13
Download Pdf Manuals
Related Search