FDK Series
Contents
1. AK AXIOMTEK FDK Series 15 17 19 Flexible Display Panel PC User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd OCopyright 2010 AXIOMTEK Co Ltd All Rights Reserved August 2010 Version A1 Printed in Taiwan Safety Approvals CE Marking FCC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are meant to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instructions this equipment might generate or radiate radio frequency e2. PenMount Touch screen Before you can use and calibrate it here is what you should do 1 Setup Penmount touch device driver by executing C Penmount Windows 2000 XP V5 0 setup exe When the installation is finished an icon PM appears on the Taskbar 2 Calibrate Penmount touch by clicking on the PM icon and the go on the calibration 3 Restart the computer 68 Installation of Drivers
3. Recommended dimensions of inner 272 50 frame of front bezel for FDK170 830 with touch 8 Introduction FDK190 830 N without touch dimensions qE E A A gt A WW 4 305 06 LCD AA 332 00 351 00 117 00 382 32 Recommended dimensions of inner frame 307 06 of front bezel for FDK190 830 without touch Introduction FDK User s Manual 6 00000000000 0 o o 0 o 6 t t o t 0 900 oo ooo o 000 900000 OOOOO OOO 002900 FDK series User s Manual FDK1 90 830 R with touch dimensions 310 00 O0 000000002 0a QUO aa 0 oq0 000 0000000 000000000 000 00 00 nm o o o o o o o o o o o e o o6 o o o o o o oo oe 000 299 65 TS AA 332 00 9 o o o oa c0o o coca coco o 00 377 90 Recommended dimensions of inner frame 302 65 of front bezel for FDK190 830 with touch 10 Introduction FDK User s Manual 1 4 O Outlets Please refer to the following illustration for I O locations of the FDK Brightness adjustment VR CompactFlash slot POWER SWITCH ATX COM 2 RS 232 Power Input connector phoenix type 8 VGA 2 X USB 2 0 9 1X ETHERNET RJ 45 COM 3 RS 232 2 X USB 2 0 COM 4 RS 232 AUDIO LINE OUT 6 COM 1 RS 23214221485 Introduction 11 FDK series User s Manual 1 5 Packing List When you receive the FDK the bundled package should contain the following items FDK unit x 1 Driver CD x
4. Select Ok to load Fail Safe defaults AMI BIOS Setup Utility 63 FDK series User s Manual CHAPTER 4 DRIVERS INSTALLATION 4 1 System FDK supports Windows 2000 XP To facilitate the installation of system driver please carefully read the instructions in this chapter before start installing 1 Insert Driver CD and select the Drivers pp 0 step 1 Step 2 Step 3 Chipset VGA Ethernet pp Step4 Step5 Stepe Audio Touch i Wireless LAN 2 Select all files and follow the installing procedure 64 Installation of Drivers FDK series User s Manual 4 2 Touch Screen The FDK uses the 5 wire analog resistve There are the specification and driver installation which are listed below 4 2 1 Specification 5 wire Analog Resistive type Touch Screen Controller PenMount 6000 USB Touch Screen Controller IC Baud Rate 19200 baud rate fixed 1024 x 1024 10 bit A D converter inside 5V Power Input pea cepe ups Active 24 6mA Idle Mode 13 4mA 4 2 2 Driver Installation Windows XP The FDK provides a touch screen driver that users can install it under the operating system Windows XP To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation 1 Insert Driver CD and follow the path to select the Drivers Step 5 Touch Windows Universal Driver V2 1 0 234 2 Follow the installing procedure
5. No and Yes gt Plug amp Play O S When the setting is No Use this item to configure all the devices in the system When the setting is Yes and if you install a Plug and Play operating system the operating system configures the Plug and Play devices not required for boot The default setting is No gt PCI Latency Timer This item controls how long a PCI device can hold the PCI bus before another takes over The longer the latency the longer the PCI device can retain control of the bus before handing it over to another PCI device There are several options for your selection gt Allocate IRQ to PCI VGA This item allows BIOS to choose an IRQ to assign for the PCI VGA card Here are the options for your selection No AMI BIOS Setup Utility FDK series User s Manual and Yes gt Palette Snooping Some old graphic controllers need to snoop on the VGA palette and then map it to their display as a way to provide boot information and VGA compatibility This item allows such snooping to take place Here are the options for your selection Disabled and Enabled gt PCIIDE BusMaster This item is a toggle for the built in driver that allows the onboard IDE controller to perform DMA Direct Memory Access transfer Here are the options for your selection Disabled and Enabled gt OffBoard PCI ISA IDE Card This item is for any other non onboard PCI ISA IDE controller adapter There are several options for your sel
6. One 2 5 SATA drive e Net Weight m 3 84 Kgs 8 46 lb FDK150 830 R m 5 52 Kgs 12 16 Ib FDK170 830 R m 5 82 Kgs 12 83 Ib FDK190 830 R e Dimension Main Body Size m 335mm 261 5mm 60mm FDK150 830 N 335mm x 261 5mm x 63 3mm FDK150 830 R 367mm x 304 5mm 65mm FDK170 830 N 367mm 304 5mm 69 3mm FDK170 830 R 404 5mm x 332mm x 65mm FDK190 830 N 404 5mm x 332mm x 69 3mm FDK190 830 R e Operation Temperature m OCto50C e Relative Humidity m 10 to 90 40 C Non Condensing e Power input m 10 30VDC with phoenix power connector Su NOTE All specifications and images are subject to change 3 without notice vy NOTE Ifthe operation temperature is higher than 406 the wide temperature DRAM is recommended to be used on the device Introduction 3 FDK series User s Manual 1 3 Product List FDK series provides three sizes of LCD 15 17 and 19 The touch screen is optional Please refer to the following table FoK150 830 N 15 1024x768 N gt FOK150 830 R 15 1024x768 Y gt aro 1280x1024 N FOK170 830 R 17 1280x1024 Y gt FOK190 830 N 19 1280x1024 N gt FoK190 830 R ter 1280x1024 Y 4 Introduction FDK User s Manual 1 4 Dimensions FDK150 830 N without touch dimensions 100 00 o o o o o o D o 0 o o t e 0000000200 0 La We 0000000009000 oOo O O QO O O O O O o o o gio
7. This setting prevents the BIOS from initiating Disabled any power saving modes concerned with the video display or monitor This option places the monitor into suspend mode after the specified period of display inactivity has expired This means the monitor is not off The screen will appear blacked out The standards do not cite specific power ratings because they vary from monitor to monitor but this setting use less power than Standby mode This is the default setting gt Hard Disk Drive Power Down Mode This option specifies the power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired The default setting is Suspend This setting prevents hard disk drive power down mode This option cuts the power to the hard disk drives during a system suspend This is the default setting Disabled gt Suspend Time Out Minute This option specifies the length of time the system waits before it enters suspend mode The default setting is Disabled Disabled This setting prevents the system from entering suspend mode This is the default setting Set this item to allow the computer system to enter suspend mode after being inactive for 1 minute Set this item to allow the computer system to enter suspend mode after being inactive for 4 minutes Set this item to allow the computer system to enter suspend mode after being inactive for 10 minutes gt Throttle S
8. Configuration The Lan Boot Settings Configuration can enable or disable Lan Boot ROM to allow the system boot on LAN BIOS SETUP UTILITY Lan Boot ROM Disabled 54 AMI BIOS Setup Utility FDK series User s Manual 3 7 Security Menu The Security menu allows users to change the security settings for the system BIOS SETUP UTILITY Change Supervisor Password gt Supervisor Password This item indicates whether a supervisor password has been set If the password has been installed Installed displays If not Not Installed displays gt User Password This item indicates whether a user password has been set If the password has been installed Installed displays If not Not Installed displays gt Change Supervisor Password Select this option and press lt Enter gt to access the sub menu You can use the sub menu to change the supervisor password gt Change User Password Select this option and press lt Enter gt to access the sub AMI BIOS Setup Utility 55 FDK series User s Manual 56 menu You can use the sub menu to change the user password gt Boot Sector Virus Protection This option is near the bottom of the Security Setup screen The default setting is Disabled Protection This is the default setting Select Enabled to enable boot sector protection It displays a warning when any program or virus issues a Disk Format command or attempts to write to the boot sector of the hard disk driv
9. Hyper Threading Technology Use this item to enable or disable Hyper Threading Technology which makes a single physical processor perform multi tasking function as two logical ones gt Intel R SpeedStep tm tech This item helps you enable or disable the Intel SoeedStep Technology gt Intel R C STATE tech AMI BIOS Setup Utility 35 FDK series User s Manual Use this item to enable or disable the C State technology gt Enhanced C States This item allows you to enable or disable any available enhanced C states C1E C2E C3E C4E and Hard C4E e IDE Configuration You can use this screen to select options for the IDE Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen For items marked with gt please press lt Enter gt for more options BIOS SETUP UTILITY ATA IDE Configuration Compatible gt ATA IDE Configuration Use this item to specify the integrated IDE controller There are three options for your selection Disabled Compatible and Enhanced gt Legacy IDE Channels When the ATA IDE Configuration is set to Compatible this item will be displayed gt Primary Secondary Third IDE Master Slave Select one of the hard disk drives to configure IDE devices 36 AMI BIOS Setup Utility FDK series User s Manual installed in the system by pressing lt Enter gt for more options e SuperlO Configuration You c
10. Q9 020 309 40 Recommended dimensions of inner frame of front bezel 233 30 for FDK150 830 without touch Introduction 5 FDK series User s Manual FDK150 830 R with touch dimensions 0 0 0 86 0 0 0 0 0 0 6 00 100 00 0000000000 Q0 e o o o 505 6 O O oo e o co oo oo so o o Ls jg 0000090002000 o O0 00000000000 O 306 50 Recommended dimensions of inner frame of front bezel for FDK150 830 with touch 230 50 6 Introduction FDK170 830 N without touch dimensions 310 00 Recommended dimensions of inner frame of front bezel for FDK170 830 without touch 276 02 ESA E TT A A A AAA AAA KO OA Goat a AAA oat ar AA SAA ERA ow goa RA SAA AAA AAA Fog EA A E A AA ATA A JP uf gat Vw E A Introduction FDK User s Manual oc 0 o ooo oo 0 00 o 00000 00000 o 0069 ss 6 o o 0000 00 0 A o 6 o 0 o o 0 00 0 o o o o oc oo ooo co 100 00 lS m 100 00 00000 0000000000 00 0 oio 0 co FDK series User s Manual FDK170 830 R with touch dimensions 310 00 o o ooo ooo 0 o0 co o coco 0 oo co co o 0 o o o o 00 00 po 269 50 TS AA 304 50 0000000 q o o o o o o o o a 9 e o e 000 0 0000 We 0 0 0 8 0 0 0 0 0 o o oo ooo 0OOOOOO OOO 0 340 00
11. lt ESC gt lt Arrow gt keys and so on Y Y Note Some of navigation keys differ from one screen to another Left Right The Left and Right lt Arrow gt keys allow you to select a setup screen Il Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen i The Plus and Minus lt Arrow gt keys allow you to Plus Minus l change the field value of a particular setup item The lt Tab gt key allows you to select setup fields The lt F1 gt key allows you to display the General Help screen 32 AMI BIOS Setup Utility FDK series User s Manual The lt F10 gt key allows you to save any changes you have made and exit Setup Press the lt F10 gt key to save your changes The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the lt Esc gt key to exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens 3 3 Main Menu When you first enter the Setup Utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab There are two Main Setup options They are described in this section The Main BIOS Setup screen is shown below system Ti Vale me BIOS SETUP UTILITY e System Time Date Use this o
12. screen BIOS SETUP UTILITY gt System Temperature CPU Temperature These items display the temperature of CPU and System Vcore etc AMI BIOS Setup Utility 39 FDK series User s Manual e ACPI Settings You can use this screen to select options for the ACPI Settings and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Suspend mode 51 POS 40 AMI BIOS Setup Utility FDK series User s Manual e APM Configuration You can use this screen to select options for the APM Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Power Management APM Enabled Video Power Down Mode Suspend gt Power Management APM Set this item to allow Power Management APM support The default setting is Enabled Set this item to prevent the chipset power management and APM Advanced Power Management features Set this item to allow the chipset power management and APM Advanced Power Management features This is the default setting gt Video Power Down Mode This option specifies the Power State that the video subsystem enters when the BIOS places it in a power saving state after the specified period of display inactivity has AMI BIOS Setup Utility 41 FDK series User s Manual 42 expired The default setting is Suspend
13. 1 SATA cable x 1 SATA power cable x 1 Phoenix connector x 1 If you can not find the package or any items are missing please contact AXIOMTEK distributors immediately 12 Introduction FDK series User s Manual CHAPTER 2 HARDWARE INSTALLATION The FDK series provides rich l O ports and flexible expansions for you to meet different demand for example CF card The chapter will show you how to install the hardware It includes CompactFlash Card Serial Port Ethernet Mounting Method Hard disk DRAM Wireless LAN Card 2 1 Open and close back cover This section tells users how to open and close the back cover Please follow the steps below Step 1 Unscrew eleven screws on the back cover Please refer the photo of top side right side and left side Hardware Installation 13 FDK series User s Manual 000090000000 6 o o o 6 o 0 9 o o o o o 8 O O O O O O O 0000000 0 e o e 6 6 O O 8 O O O O Step 2 When users open the back cover there is a cable connecting between a fan and the motherboard 14 Hardware Installation FDK series User s Manual 2 _ m aeae 4 Step 3 Remove the connector first before remove the back cover totally Step 4 After removing the back cover users can see the inside of the unit Hardware Installation 15 FDK series User s Manual Step 5 Before closing the back cover users must connect the fan cable to
14. Manual 2 3 Ethernet The FDK is equipped with a high performance Plug and Play Ethernet interface full compliant with IEEE 802 3 standard and can be connected with a RJ 45 LAN connector Please refer to detailed pin assignment list below TX Data transmission positive TX Data transmission negative Rx Data reception positive MES Rx Data reception negative 8 Ry45termination Hardware Installation 21 FDK series User s Manual 2 4 Openframe and VESA Mountings There are two mounting ways for the FDK series openframe and VESA mountings 2 4 1 Openframe Mounting The FDK series can be mounted into the wall or put on customized front bezel Please follow the steps below to for the open frame mounting installation Step 1 Users need to prepare the front bezel wall screws nuts sponge and L type holders by themselves Step2 Follow section 1 4 dimensions and drawing below Place the FDK unit on the front bezel or wall Step3 Screw the FDK to fix it 7 MA 0 7 Nuts 22 Hardware Installation FDK series User s Manual 2 4 2 VESA Mounting FDK series provides two types of VESA holes 75mm x 75mm and 100mm x 100mm These VESA holes can easy for users to install FDK seris via many different types of VESA mounting holders such as VESA arm VESA wall holders etc 100 00 D Hardware Installation 23 FDK series User s Manual 2 5 HDD Installation The FDK provides a co
15. Select This item allows you to select the amount of system memory used by the internal graphics device gt Video Function Configuration Press lt Enter gt for the sub menu for setting up video function 58 AMI BIOS Setup Utility FDK series User s Manual BIOS SETUP UTILITY DUMT Mode Select DUMT Model AMI BIOS Setup Utility 59 FDK series User s Manual e South Bridge Configuration BIOS SETUP UTILITY USB Functions Enabled 60 AMI BIOS Setup Utility FDK series User s Manual BIOS SETUP UTILITY PCIE Port 5 1080010 Enable Disabled gt USB Function This item allows you to enable or disable USB function gt USB 2 0 Controller This item allows you to enable or disable the USB 2 0 controller gt Audio Controller This item allows you to enable or disable the audio support gt SLP_S4 Min Assertion Width This item allows you to set the SLP_S4 Assertion Width gt Restore on AC Power Loss This item can control how the PC will behave once power is restored following a power outage or other unexpected shutdown gt PCIE Port Configuration AMI BIOS Setup Utility 61 FDK series User s Manual This item allows you to set or disable the PCI Express Ports 3 9 Exit Menu The Exit menu allows users to load your system configuration with optimal or failsafe default values O BIOS SETUP UTILITY save Changes and Exit 62 gt Save Changes and Exit When you have completed the s
16. an use this screen to select options for the SuperlO Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Serial Porti Address serial Porti IRQ gt Serial Porti Address This item specifies the base I O port address and Interrupt Request address of serial port 1 The Optimal setting is 3F8 IRQ4 The Fail Safe default setting is 3F8 gt Serial Port1 IRQ This item specifies the IRQ used by the serial port 1 gt Serial Port2 Address This item specifies the base I O port address and Interrupt Request address of serial port 2 The Optimal setting is 2F8 IRQ3 The Fail Safe setting is 2F8 AMI BIOS Setup Utility 37 FDK series User s Manual gt Serial Port2 IRQ This item specifies the IRQ used by the serial port 2 gt Serial Port3 Address This item specifies the base I O port address and Interrupt Request address of serial port 3 gt Serial Port3 IRQ This item specifies the IRQ used by the serial port 3 gt Serial Port4 Address This item specifies the base I O port address and Interrupt Request address of serial port 4 gt Serial Port4 IRQ This item specifies the IRQ used by the serial port 4 38 AMI BIOS Setup Utility FDK series User s Manual e Hardware Health Configuration This screen shows the Hardware Health Configuration and a description of the selected item appears on the right side of the
17. and press OK Installation of Drivers 65 FDK series User s Manual 3 Click Start menu and select PenMount Utilities and then a PenMount Control Panel pops out PenMount Control Panel Device Multiple Monitors Tools About I Penmount Control Panel Version 1 0 0 19 Installed Device s Device O PenMount 6000 USE Support E mail penmocnt amp seed net tw Support Website http Ars penmaunt com tw 66 Installation of Drivers FDK series User s Manual 4 Select the Standard Calibrate tab 47 Device 0 PenMount 6000 USB Calibrate Setting Edge Compensation AboLt Advanced Mode E Plot calibration data Standard Calibration Advanced Calibration Turn off EEPROM storage 5 Calibration To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration va I Touch the red square 6 Press OK Installation of Drivers 67 FDK series User s Manual 4 3 Embedded O S The FDK provides the Windows XP Embedded and Windows CE Net 6 0 The O S is supported devices which are listed below 4 3 1 Windows XP Embedded Here are supported onboard devices E Onboard Multi I O SATA HDD USB E PS2 Keyboard and mouse CRT LCD display 10 100 1000 base T Ethernet z Compact Flash a Onboard Audio Touch Screen
18. ars on the right side of the screen BIOS SETUP UTILITY Active State Pouer Management Disabled gt Active State Power Management Use this item to enable or disable the function of Active otate Power Management to provide you with lower power consumption The default setting is Disabled AMI BIOS Setup Utility 45 FDK series User s Manual e USB Configuration You can use this screen to select options for the USB Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Legacy USB Support Enabled gt Legacy USB Support Use this item to enable or disable support for USB device on legacy operating system The default setting is Enabled gt USB 2 0 Controller Mode Use this item to configure the USB 2 0 controller The default setting is HiSpeed gt BIOS EHCI Hand Off Enabling this item provide the support for operating systems without an EHCI hand off feature The default setting is Enabled 46 AMI BIOS Setup Utility FDK series User s Manual 3 5 PCI PnP Menu The PCI PnP menu allows users to change the advanced settings for PCI PnP devices BIOS SETUP UTILITY Clear NURAM AMI BIOS Setup Utility 47 FDK series User s Manual BIOS SETUP UTILITY Reserved Memory Size Disabled 48 gt Clear NVRAM Use this item to clear the data in the NVRAM CMOS Here are the options for your selection
19. at the FDK must be properly grounded The brightness of the flat panel display will be getting weaker as a result of frequent usage However the operating period varies depending on the application environment Turn OFF the system power before cleaning Clean the system using a cloth only Do not spray any liquid cleaner directly onto the screen The FDK may come with or w o a touchscreen Although the touchscreen is chemical resistant it is recommended that you spray the liquid cleaner ona cloth first before wiping the screen In case your system comes without the touchscreen you must follow the same procedure and not spray any cleaner on the flat panel directly Avoid using sharp objects to operate the touchscreen Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen The flat panel display is not susceptible to shock or vibration When assembling the FDK make sure it is securely installed Do not open the system s back cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions e Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body e When handling boards and
20. cations lts slim ID can fits into any space or encased in any chassis this series comes with a front panel open frame design available currently in 15 17 and 19 LCD sizes Other than offering above configuration advantages this open frame panel computer series also highlights an ultra slim profile and compact footprint in thickness of 60mm for any space Moreover the brightness adjustment knob located on the back cover makes maintenance easier and faster For WiFi amp 3G connection this slim Introduction 1 FDK series User s Manual unit incorporates a Mini Card slot for expansion capability 1 2 Specifications 1 2 1 Main CPU Board e CPU m Intel Atom N270 1 6GHz processor with FSB 533MHz onboard e System Chipset m 945GSE ICH7M e BIOS m America Megatrends BIOS e System Memory One 200 pin DDR2 SO DIMM socket Maximum memory up to 2GB 1 2 2 I O System e Standard I O m Three RS 232 and one RS 232 422 485 m Four USB 2 0 e Ethernet m One RTL81111b Gigabit Ethernet e Audio m One Line out e Expansion One Mini card e Storage One slot for CF card m One SATA e Power connector Phoenix power connector 2 Introduction FDK User s Manual 1 2 3 System Specification e 15 1024x768 17 1280x1024 or 19 1280x1024 TFT LCD m One VH for brightness control e Touch equip on FDK1x0 830 R models 5 wired resistive touch e Heat Dispensing Design e Disk drive housing
21. components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Atom M are registered trademarks of Intel Corporation MS DOS Microsoft C and Quick BASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents DISC HAIG Sinai id 1 odale PAD DNOV Al S vedi sete zh lii Salely IV CHAPTER 1 eere eee een nnnnnno 1 1 1 General 265071010 N 1 1 2 9 PECMICA ON Sica teta cinc decada 2 k24 Man G PU DOM said 2 122 IOSVSena albi Deol liada 2 2 9 SYSIEMSSPecificalon iaia 3 1 3 TRIP 4 1 4 ios 5 1 4 RE 11 1 5 PACKING M TR 12 CHAPTER 2 HARDWARE INSTALLATION 13 2 1 Open and close back cover 13 2 2 CF card Installation 17 2 2 Serial Ports asirscinssiniintitsuortuierensnuiis 19 2 3 21 2 4 Openframe and VESA 22 2 4 1 Openframe Mounting i 22 242 VESA und uotee v UU ab auucuC 23 2 5 HDD IristallatlOn scc
22. cose uten bern 24 2 6 DRAM Instala scsi da 26 2 7 Wireless LAN Card Installation 28 CHAPTER 3 AMI BIOS SETUP UTILITY 32 3 1 o A 32 3 2 Navigation KEYSs eese 32 3 3 lalla 33 3 4 Advanced MenU 34 3 5 Ci BNR IMEI ea 47 3 6 BOOLMENU tan m 50 3 7 Security Meninas 55 VI 3 8 Chipset Melo as a 57 3 9 EXE MON Usado cidade 62 CHAPTER 4 DRIVERS INSTALLATION 64 4 1 SSR E ee eee RT 64 4 2 OUCH SOCIO CN sities sat 65 42 0 ER 5 4 2 2 Driver Installation Windows 705 eee eeee es 65 4 3 Embedded 02S entidades 68 4 3 1 Windows XP 68 vil MEMO viii FDK User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the FDK series Chapter 1 includes the following sections General Description Specification Dimensions I O Outlets Package List 1 1 General Description The FDK series is an open frame touch panel computer equipped with a TFT LCD display and low power consumption Intel Atom N270 1 6GHz processor with FSB 533MHz The FDK series supports Windows 7 Windows XP and Windows XP embedded The panel computer is able to install a CompactFlash M card and provide a Mini card slot for wireless module This slim series is designed for immediate integration and can be widely deployed in indoor kiosk HMI automation and many more appli
23. e If enabled the following appears when a write is attempted to the boot sector You may have to type N several times to prevent the boot sector write Boot Sector Write Possible VIRUS Continue Y N The following appears after any attempt to format any cylinder head or sector of any hard disk drive via the BIOS INT 13 Hard disk drive Service Format Possible VIRUS Continue Y N Enabled AMI BIOS Setup Utility FDK series User s Manual 3 8 Chipset Menu The Chipset menu allows users to change the advanced chipset settings You can select any of the items in the left frame of the screen to go to the sub menus North Bridge Configuration e South Bridge Configuration For items marked with gt please press Enter for more options BIOS SETUP UTILITY North Bridge Configuration AMI BIOS Setup Utility 57 FDK series User s Manual e North Bridge Configuration BIOS SETUP UTILITY DRAM Frequency E l gt DRAM Frequency This item allows you to control the Memory Clock gt Configure DRAM Timing by SPD This item can enable or disable DRAM timing by SPD Serial Presence Detect device which is a small EEPROM chip on the memory module containing important information about the module speed size addressing mode and various parameters gt Boot Graphic Adapter Priority This item allows you to select the graphics controller as the primary boot device gt Internal Graphics Mode
24. ection gt 1RQ3 4 5 7 9 10 11 14 15 These items will allow you to assign each system interrupt a type depending on the type of device using the interrupt The option Available means the IRQ is going to assign automatically Here are the options for your selection Available and Reserved gt DMA Channel 0 1 3 5 6 7 These items will allow you to assign each DMA channel a type depending on the type of device using the channel The option Available means the channel is going to assign automatically Here are the options for your selection Available and Reserved AMI BIOS Setup Utility 49 FDK series User s Manual 3 6 Boot Menu The Boot menu allows users to change boot options of the system You can select any of the items in the left frame of the screen to go to the sub menus Boot Settings Configuration Boot Device Priority Removable Drives Lan Boot Settings Configuration For items marked with gt please press Enter for more options BIOS SETUP UTILITY Boot Settings Configuration 50 AMI BIOS Setup Utility FDK series User s Manual e Boot Settings Confiquration BIOS SETUP UTILITY Quick Boot Enabled gt Quick Boot Enabling this item lets the BIOS skip some power on self tests POST The default setting is Enabled gt Quiet Boot Set this item to allow the computer system to display the POST messages Set this item to allow the computer system to displa
25. low Clock Ratio Use this item to specify the speed of the system clock when running the power saving states gt Power Button Mode This option specifies how the externally mounted power button on the front of the computer chassis is used The AMI BIOS Setup Utility FDK series User s Manual default setting is On Off Pushing the power button turns the computer On Off on or off This is the default setting This is the default setting Pushing the power button places the computer in Suspend mode or Full On power mode Advanced Resume Event Controls gt Resume On Ring This item enables or disables the function of Resume On Ring that resumes the system through incoming calls gt Resume On RTC Alarm You can set Resume On RTC Alarm item to enabled and key in Data time to power on system AMI BIOS Setup Utility 43 FDK series User s Manual e MPS Configuration This screen shows the MPS Multi Processor Specification Configuration and you can change its value A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY MPS Revision gt MPS Revision Use this item to select MPS Multi Processor Specification Revision 1 1 or 1 4 The default setting is 7 4 44 AMI BIOS Setup Utility FDK series User s Manual e PCI Express Configuration This screen shows the PCI Express Configuration and you can change its value A description of the selected item appe
26. nergy and cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following methods Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment to another outlet of a circuit that doesn t connect with the receiver 4 Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with the emission limits Safety Precautions Before getting started please read the following important safety precautions The FDK does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cord from the FDK before any installation Be sure both the system and external devices are turned OFF A sudden surge of power could ruin sensitive components th
27. ns and illustration Step 1 Refer to section 2 1 to open the back cover and find out mini card slot on mainboard TTTITI ren EIE DIM FUEL Pr 76 0348 503 ug dM 108 00 PC2 5900 CLI Step 2 Insert the wireless LAN card to the slot Push it down firmly until it is clipped by the slot 28 Hardware Installation FDK series User s Manual Step 3 Remove the antenna plug from the top of back cover Step 4 Install the antenna cable on the back cover Hardware Installation 29 FDK series User s Manual Step5 Install the antenna on the antenna connector 30 Hardware Installation FDK series User s Manual MEMO Hardware Installation 31 FDK series User s Manual CHAPTER 3 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the AMI BIOS setup utility 3 1 Starting To enter the setup screens follow the steps below 1 Turn on the computer and press the Del key immediately After you press the lt Delete gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Chipset and Power menus 3 2 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F10 gt lt Enter gt
28. nvenient Hard Disk Drive HDD bracket for users to install 2 5 SATA HDD Please follow the steps Step 1 Refer section 2 1 to open the back cover Step 2 Unscrew 4 screws to take off the HDD bracket Step 3 Fix the HDD on bracket by 4 screws and connect SATA cable as well as power cable 24 Hardware Installation FDK series User s Manual Step 4 Fix the HDD bracket into the system and plug the data and power cable to HDD Installation completes ____sitt np un Eve 5 Vex Hardware Installation 95 FDK series User s Manual 2 6 DRAM Installation The FDK provides one 200 pin DDR2 SODIMM socket that Support system memory up to 2GB Please follow steps below to install the memory modules Step 1 Refer to section 2 1 to open the back cover and find out DIMM socket on mainboard SBC87830 A e hd otep2 Insert the DRAM to the DIMM socket and then push it down firmly until it is clipped by the socket 26 Hardware Installation Step 3 Installation completes an rs ii i LM gt Lia Ww IU HE 8 LE wem coni Hardware Installation FDK series User s Manual 27 FDK series User s Manual 2 7 Wireless LAN Card Installation The FDK provides one Mini card slot for user to install one wireless LAN card When installing the wireless LAN card refer to the following instructio
29. ption to change the system time and date Highlight AMI BIOS Setup Utility 33 FDK series User s Manual System Time or System Date using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Arrow gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format 3 4 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the screen to go to the sub menus CPU Configuration IDE Configuration SuperlO Configuration Hardware Health Configuration ACPI Configuration APM Configuration MPS Configuration PCI Express Configuration USB Configuration For items marked with gt please press Enter for more options BIOS SETUP UTILITY CPU Configuration 34 AMI BIOS Setup Utility FDK series User s Manual e Configure advanced CPU settings This screen shows the CPU Configuration and you can change the value of the selected option BIOS SETUP UTILITY Max CPUID Value Limit Disabled Execute Disable Bit Capability Enabled gt Max CPUID Value Limit You can enable this item to let legacy operating systems boot even without support for CPUs with extended CPU ID functions gt Execute Disable Bit Capability This item helps you enable or disable the No Execution Page Protection Technology gt
30. the motherboard first mint A set A ARA Step 6 Then close back cover and fix back the eleven screws 16 Hardware Installation FDK series User s Manual 2 2 CF card Installation The FDK series provides one CF slot for users to install CompactFlash M card Please refer to the following instructions for installation Step 1 Turn off the system and unplug the power cord Step 2 Locate the CompactFlash socket and insert the card into the socket Hardware Installation 17 FDK series User s Manual 18 Hardware Installation FDK series User s Manual 2 2 Serial Ports Interface The FDK has four serial ports COM1 is RS 232 422 485 while COM2 COM3 and COM4 are RS 232 The following table shows you the pin assignments of this connector _1 bata Carer Deea 000 6 pata et Ready OSA Cs enemi Data mo 8 oem tosens crs La pata Terminal Ready 5 oran EP 10 0 0 0 0 In addition COM1 can be set for RS 232 422 485 by jumper The jump setting is listed as below Hardware Installation 19 FDK series User s Manual When COMI is set to RS 422 or RS 485 the pin assignments are listed below Ping e 88422 85485 2 DATA 3 RX Noconnector 4 Ax Noconnector 5 Noconnecto Noconnector 6 Noconnector Noconnector _ 8 Noconnector Noconnector 9 w GND 20 Hardware Installation FDK series User s
31. y the OEM logo This is the default setting gt AddOn ROM Display Mode This item selects the display mode for option ROM The default setting is Force BIOS gt Boot Num Lock Use this item to select the power on state for the NumLock The default setting is On gt PS 2 Mouse Support This item determines if the BIOS should reserve IRQ12 for the PS 2 mouse or allow other devices to make use of this AMI BIOS Setup Utility 51 FDK series User s Manual IRQ Here are the options for your selection Auto Enabled and Disabled gt Wait For F1 If Error If this item is enabled the system waits for the F1 key to be pressed when error occurs The default setting is Enabled gt Hit DEL Message Display If this item is enabled the system displays the message Press DEL to run Setup during POST The default setting is Enabled e Boot Device Priority The Boot Device Priority screen specifies the the boot device priority sequence from the available devices BIOS SETUP UTILITY ist Boot Device USB Generic STORAG 52 AMI BIOS Setup Utility FDK series User s Manual e Removable Drives Use this screen to view the removable drives in the system The BIOS will attempt to arrange the removable drive boot sequence automatically You can also change the booting sequence BIOS SETUP UTILITY lst Drive USB Generic STORAG AMI BIOS Setup Utility 53 FDK series User s Manual e Lan Boot Settings
32. ystem configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Exit from the Exit menu and press lt Enter gt Select Ok to save changes and exit gt Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration Select Discard Changes and Exit from the Exit menu and press lt Enter gt Select Ok to discard changes and exit gt Discard Changes AMI BIOS Setup Utility FDK series User s Manual Use this item to abandon all changes gt Load Optimal Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Optimal settings are designed for maximum system performance but may not work best for all computer applications In particular do not use the Optimal Setup options if your computer is experiencing system configuration problems Select Load Optimal Defaults from the Exit menu and press lt Enter gt gt Load Fail Safe Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Fail Safe settings are designed for maximum system stability but not maximum performance Select the Fail Safe Setup options if your computer is experiencing system configuration problems Select Load Fail Safe Defaults from the Exit menu and press lt Enter gt
Download Pdf Manuals
Related Search