ENX-US15WP
Contents
1. 20V Vous 249 VBAT 3VSB V 24 A WA m t Enter Select PU PD Value 10 5 ESC Exit F1 General Help F5 Previous Values FT Setup Defaults 2 2 6 1 System Temperature This shows you the current temperature of system 2 2 6 2 CPU Temperature This shows the current CPU temperature 2 2 6 3 Chassis FAN Speed This shows the Chassis FAN Speed RPM 2 2 6 4 VCore and Others Voltage This shows the voltage of VCORE 12 5V VCCP V AVCC V VBAT V and 3VSB V User s Manual 2 2 7 Load Setup Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations While Award has designed the custom BIOS to maximize performance the factory has the right to change these defaults to meet their needs Press lt Y gt to load the default values setting for optimal performance system operations Phoenix AwardBIOS CMOS Setup Utility Load Setup Defaults Load Setup Defaults 4 Select Item Exit Setup Load Setup Defaults ENX US15WP 51 ENX US15WP 2 2 8 Set Supervisor Password You can set supervisor password It is able to enter change the options of setup menus Phoenix AwardBIOS CMOS Setup Utility Set Supervisor Password Enter Password Ese Quit Select Item 10 Save Exit Setup Change Set Disable Password Foll2. ATX Power Sze LW weigh Specifications are subject to change without notice 10 Block Diagram Intel ATOM 510P 530 CPU CH 317 US15WP SCH 4 High Speed USB Ports REALTEK ALC888 HD Codec 18 24BitLVDS LPC Winbond Super 1 0 W83627DHG FWH User s Manual DDR2 400 533 IDE 1 x Mini PCle REALTEK RTL8111C Gigabit LAN ENX US15WP 11 ENX US15WP This chapter describes the main board features and the new technologies it supports Prod introdu 1 n 12 User s Manual Production ntroduction 1 1 Before you Proceed Take note of the following precautions before you install motherboard components or change any motherboard settings Unplug the power cord from the wall socket before touching any A component Use grounded wrist strap or touch a safely grounded object or a metal object such as the power supply case before handling components to avoid damaging them due to static electricity Hold components by the edges to avoid touching the ICs on them Whenever you uninstall any component place it on a grounded antistatic pad or in the bag that came with the component Before you install or remove any component ensure that the ATX power supply is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components ENX US1
3. 23 162 Chassis Fan Connector Ch RE 24 1 6 3 Serial Port Connector 1 COM 24 1 6 4 System Panel Connector 25 1 6 5 Primary EIDE Connector DE 26 160 LOD Inverter Connector EE 27 TO Connector 010 28 EVDS COomnector JLVDS itx da tun De ipt buic 28 1 6 9 Audio Line In Connector LINE 29 1 6 10 ATX Power Connector MATAPW RZ E 29 1 6 11 USB 2 0 Connector USB EEN 30 User s Manual Contents BIOS Setup 32 BOS d a ee 32 LN gt EE 33 A d oa 33 2 _ __________________ 33 22 BIOS Monu OBI ee ne nee ee ee eee MENU 34 221 Standard ele Ee 35 2 2 2 Advanced BIOS ER 37 2 2 3 Advanced Chipset Features 41 Mutegrateceriplierels 43 225 in sie Leonie EE 48 fers nce due tors un 50 2 2 Setup Defaults sissi i 51 2 20 e EE le e EE 52 ISON AS SONG aasi ET 59 2 2 10 Save and b EE 54 2 2 11 Exit Without Saving 55 ENX US15WP 3 ENX US15WP Safety I nformation Electrical safety To prevent el
4. ENX US15WP Intel amp Atom Processor Nano ITX Motherboard User s Manual MENU Ver 1 04 ENX US15WP Contents RENTE TETTE T TTE 4 Safety Declaration 5 Kell lee oro EE 5 Conventions Used in This 5 PACKING 6 Revision History EEN 7 EE e EE 8 Block D se tte 11 Production 13 you A eee 13 1 2 le ele lee 14 1 2 1 Placement Direction gt 14 1 2 2 Screw dae 14 _________________ _ eee 15 E e C ona 16 l4 un e aeres ee 17 141 DIMM Sockets Location 17 142 EE 18 1 4 3 Installing a DDR2 NIR terre 19 1 4 4 Removing a DDR2 20 E une 21 Cer CMO S 5 5 gt _ 21 1 5 2 COM RI 5V 12V Select EEN 22 EIERE 23 1 6 1 Rear Panel
5. If you encounter technical problems with the product contact a qualified service technician or your retailer The symbol of the crossed out wheeled bin indicates that the product electrical and electronic equipment should not be placed in municipal waste Check local regulations for disposal of electronic products User s Manual Safety Declaration This device complies with the requirements in Part 15 of the FCC rules Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesired operation Technical Support If a problem arises with your system and no solution can be obtained from the user s manual please contact your place of purchase or local distributor Alternatively please try the following help resources for further guidance Visit the Avalue website http www avalue com tw Conventions Used in This Guide To make sure that you perform certain tasks properly take note of the following symbols used throughout this manual DANGER WARNING Information to prevent injury to yourself when trying to complete a task CAUTION Information to prevent damage to the components when trying to complete a task IMPORTANT Instructions that you MUST follow to complete task VA NOTE Tips and additional information to help you complete a task ENX
6. Resources Controlled By Auto ESCD IR Resources Press Enter Palette Snoop Disabled PCI Express relative items Maximum Payload Size 128 1 Enter Select PU PD Value Fi Save ESC Exit Fi General Help F5 Previous Values Setup Defaults 2 2 5 1 Init Display First The options are PCI slot Onboard PCIEx 2 2 5 2 Rest Configuration Data The default is Disabled Select Enabled to reset Extended System Configuration Data ESCD if you have installed a new add on card and system reconfiguration has caused such a serious conflict that the OS cannot boot 2 2 5 3 Resource Controlled By The commands here are Auto ESCDY or Manual Choosing Manual requires you to choose resources from the following sub menu Auto ESCD automatically configures all of the boot and Plug and Play devices but you must be using Windows 95 or above User s Manual 2 2 5 4 PCI VGA Palette Snoop This is set to Disabled by default The options Disabled Enabled 2 2 5 5 Maximum Payload Size This allows you to set the maximum TLP payload size for PCI Express devices The option 128 bytes ENX US15WP 49 ENX US15WP 2 2 6 PC Health Status Phoenix AwardBIOS CMOS Setup Utility PC Health Status System Temperature AAC 111F CPU Temperature 24C TSF CHASSIS FAN Speed CPU VCore V 12 12 09 62V VCOCP
7. 6 Spread Spectrum The options Disabled Enabled 42 User s Manual 2 2 4 Integrated Peripherals Use this menu to specify your settings for integrated peripherals Phoenix AwardBIOS CMOS Setup Utility Integrated peripherals OnChip IDE Device Press Enter Onboard Device Press Enter Onboard Lan Boot ROM Disab led Menu Level p Power ON Function BUTTON ONLY Power ON Password Enter Hot Key Power ON Ctrl F1 Onboard Serial Port 1 SFB TROA PWRON After PWR Fail Oft Watch Dog Timer Select Disab led USB Device Setting Press Enter t gt Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values FT Setup Defaults ENX US15WP 43 ENX US15WP 2 241 OnChip IDE Device Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Enabled Item Help On Chip Primary PCI IDE Enabled EN Menu Level If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read writes per Sector drive support t Enter Select PU SPD Value 10 Sage ESC Exit Fi General Help F5 Previous Values Setup Defaults HDD Block Model If the IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support e On Chip Primary
8. F KB Power C Hot Key Pc Onboard Se Disabled PWRON Afte 10 Sec Watch Dog 20 Sec USB Device 30 Sec 40 m m mom om omm kel su ENTER Accept ESC Abort EN t Enter Select PUSPD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values Setup Defaults 46 User s Manual 2 2 4 8 USB Device Setting Phoenix AwardBIOS CMOS Setup Utility USE Device Setting 1 0 Controller Enabled Enabled 4 2 0 Controller Operation Mode High Speed Menu Level Keyboard function Enabled Storage Funct ion Enabled Enabled Disable Universal Host Controller Interface for Universal Serial Bus t gt Enter Select PU PD Value 10 Sage ESC Exit 1 1 Help F5 Previous Values Setup Defaults USB 1 0 2 0 Controller The choices Disabled Enabled USB Operation Mode Allows you to configure the USB 2 0 controller in HiSpeed 480 Mbps or Full Speed 12 Mbps Configuration options Full Low Speed HiSpeed USB Keyboard Function The choices Disabled Enabled USB Storage Function The choices Disabled Enabled ENX US15WP 47 ENX US15WP 2 2 5 PnP PCI Configurations Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Init Display First PCL Slot Item Help Reset Configuration Data Disab led Menu Level p
9. N Except when clearing the CMOS never remove the cap on CLRTC jumper default position Removing the cap will cause system boot failure AT EI Normal Default Clear CMOS ENX US15WP 21 ENX US15WP 1 5 2 RI 5V 12V Select JCOMPWR1 RI Default 6 RI Default 2 6 1 5 5V 2 6 lt E 5 1 12V 2 D 6 1 22 User s Manual 1 6 Connectors 1 6 1 Rear Panel Connectors Function Description PS 2 mouse connector The standard PS 2 mouse DIN connector is for a PS 2 mouse VGA port This 15 pin port is for a VGA monitor or other VGA compatible devices USB12 USB 2 0 connector These two 4 pin Universal Serial Bus USB ports are available for connecting USB 2 0 devices LAN RJ 45 connector This port allows Gigabit connection to a ACTILINK SPEED Local Area Network LAN through a LED LED network hub Refer to the table below for the LAN port LED indications The optional 10 100 Mbps LAN controller allows 10 100 Mbps connection to a Local Area Network LAN through a network hub ACT LINK LED SPEED LED Status Description Status Description OFF 10Mbps connection OFF No link Orange 100Mbps connection ORANGE Linked Blinking 1Gbps connection GREEN Data activity Microphone port This port connects a microphone LINE OUT Line Out port Lime This port connects a headphone o
10. PATA interface 1 x Chassis Fan header eit GPIO 4 in 4 out Clock CK540 System Memory Monitoring CPU temperature voltage and cooling fan status Auto throttling H W Status Monitor control when CPU overheats Expansion Slots 1 x Mini PCle 1 x DIO 8 bit General Purpose for 4 DI and 4 DO 53 54 53 54 Wake up on LAN Both PXE RPL WOR Ring SmartFan Control Support 3 modes Silent Optimal Performance User s Manual Specifications Summary Display Chipset Intel System Controller Hub US15WP Display Memory Intel Graphics Media Accelerator 500 Intel GMA 500 LVDS Display 1366 x 768 85 MHz Max Resolution Ext Display 1280 x 1024 85 Hz maximum resolution Audio Audio Codec Realtek ALC 888 co lay ALC 888 Audio Interface Mic in Line out 2 jack Line in pin header Ethernet Realtek RTL 8111C Gigabit LAN Back I O Port 1 x PS2 KB MS 1 x VGA port 2 x USB 2 0 1 1 1 x LAN RJ45 port 1 x Audio Mic in 1 jack 1 x Audio Line out 1 jack Back Panel Internal UO Connector 1 x USB connectors support additional 2 USB ports 1 x 6 pin ATX Power connector 1 x COM port w power pin header 1 x LVDS connector Internal LO 1 x Chassis FAN connector 1 x GPIO connector 1 x PATA interface 1 x Audio Line in ENX US15WP 9 ENX US15WP Specifications Summary Mechanical amp Environmental Power Requirement 4 Power
11. US15WP 1 4 2 Memory Configurations You can install 256MB 512MB 1GB and 2GB DDR2 SDRAM DIMMs into the SODIMM sockets using the memory configurations in this section d e Installing DDR2 DIMM other than the recommended IN configurations may cause memory sizing error or system boot failure Use any of the recommended configurations Due to chipset resource allocation the system may detect less than 1 GB system memory when you installed one 1 GB DDR2 memory modules This motherboard does not support memory modules made up of 128 Mb chips or single sided x8 memory modules Make sure that the memory frequency matches the CPU FSB Front Side Bus Refer to the Memory frequency CPU FSB synchronization table 18 User s Manual 1 4 3 Installing DDR2 DIMM DIMMs or other system components Failure to do so may cause Make sure to unplug power supply before adding or removing severe damage to both the motherboard and the components 1 Locate the DIMM socket on the board 2 Hold two edges of the DIMM module carefully and keep away of touching its connectors 3 Align the notch key on the module with the rib on the slot 4 Firmly press the modules into the socket automatically snaps into the mounting notch Do not force the DIMM module in with extra force as the DIMM module only fit in one direction Mounting Notch Notch key Ejector Flector A DDR2 DIMM is keyed with a notch so that it fits in only one
12. scroll through the various sub menus and make your selections from the available options using the navigation keys The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance If the system becomes unstable after changing any BIOS settings load the default settings to ensure system compatibility and stability Select the Load Optimized Defaults from the BIOS menu screen The BIOS setup screens shown in this section are for reference purposes only and may not exactly match what you see on your screen Visit the system builder s website to download the latest BIOS file for this motherboard 32 User s Manual 2 1 1 Legend Box The keys in the legend bar allow you to navigate through the various setup menus Key s Function Description F SC 1 5 T 9 2 1 2 List Box This box appears only in the opening screen The box displays an initial list of configurable items in the menu you selected 2 1 3 Sub menu P Note that a right pointer symbo appears to the left of certain fields This pointer indicates that you can display a sub menu from this field A sub menu contains additional options for a field parameter To display a sub menu move the highlight to the field and press Enter The sub menu appears Use the legend keys to enter values and move from field to field within a sub menu as you would within a menu Use the lt Esc gt key to return to th
13. 5WP 13 ENX US15WP 1 2 Motherboard Overview Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Refer to the chassis documentation before installing the motherboard Make sure to unplug the power cord before installing or removing the motherboard Failure to do so can cause you physical injury and damage motherboard components 1 2 1 Placement Direction When installing the motherboard make sure that you place it into the chassis in the correct orientation The edge with external ports goes to the rear part of the chassis as indicated in the image below 1 2 2 Screw Holes Place four 4 screws into the holes indicated by circles to secure the motherboard to the chassis A Do not over tighten the screws Doing so can damage the motherboard Place this side towards the rear of the chassis 14 User s Manual 1 3 Motherboard Layout JCOMPWR2 CLRTC COM2 F_PANEL IDE CF Rear Side Ei MINI PCIE 2290999249 ee ee 25022 29219 z un 55556 JLVDS amb JBKL pu Controller Hu US15WP 22222122 Sep Atom Processor 7510P 1 1GHz JCOMPWR1 4 9 9 9 1 9 Lu CHA eg 2530 1 6GHz EE 1 USB34 SO DIMM Rear Side Rm w 400 MATXPW
14. 9172K Total Memory 20817936K EN l Hove Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values Setup Defaults 2 2 1 1 Date Day xxxx The date format is week month day year 2 2 1 2 Time xx xx xx The time format is hour minute second based on 24 hour clock ENX US15WP 35 ENX US15WP 2 2 1 3 IDE Channel 0 Master Slave IDE HDD Auto Detection Press Enter to select this option for automatic device detection IDE Channel Master None Select this when no IDE device is used The system will skip the auto detection setup to make system start up faster Auto Automatically detects IDE devices during POST Manual User can manually input the correct settings Access Mode The options are CHS LBA Large Auto Capacity Capacity of currently installed hard disk Cylinder Number of cylinders Head Number of heads Precomp Write precomp landing Zone Landing zone Sector Number of sectors 2 2 1 4 Video This category detects the type of adapter used for the primary monitor that must match your video display card and monitor EGA VGA Enhanced Graphics Adapter Video Graphics Array For EGA VGA SVGA or PGA monitor adapters CGA 40 Color Graphics Adapter power up in 40 column mode CGA 80 Color Graphics Adapter power up in 80 column mode MONO Monochrome adapter includes high resolution m
15. Connector MATXPWR2 This connector is for ATX power supply plugs The power supply plugs are designed to fit this connector in only one orientation Find the proper orientation and push down firmly until the connectors completely fit GND VCC VCCI bnt VCCSB5 ATX_PSON GND Important notes on the Motherboard Power Requirements Make sure that your ATX 12V power supply can provide 5A LA the 12V lead and at least 2A on the 5 volt standby lead 5VSB The minimum recommended wattage is 36W or 65W for a fully configured system The system can become unstable and might experience difficulty powering up if the power supply is inadequate You must install PSU with a higher power rating if you intend to install additional devices ENX US15WP 29 ENX US15WP 1 611 USB 2 0 Connector 05834 This connector is for USB 2 0 ports Connect the USB GAME module cable to any of these connectors and then install the module to a slot opening at the back of the system chassis This USB connector complies with USB 2 0 specification that supports up to 480 Mbps connection speed GND USB USB USB 5V USB 5V Never connect a 1394 cable to the USB connectors Doing so will damage the motherboard Z The USB module is purchased separately 30 User s Manual This chapter tells how to change the system set tings through the BIOS setup menus Detailed descriptions of the BIOS pa
16. N direction DO NOT force a DIMM into a socket to avoid damaging the DIMM The DDR2 DIMM sockets do not support DDR DIMMs DO NOT install DDR DIMMs to the DDR2 DIMM socket ENX US15WP 19 ENX US15WP 1 4 4 Removing a DDR2 DIMM 1 Press the two ejector tabs on slot outward simultaneously and then pull out the DIMM module Mounting Notch Notch key DOR SS Al aj 2 NI Hib i 00 M Support the DIMM lightly with your fingers when pressing the ejector tabs The DIMM might get damaged when it flips out with extra force 20 1 5 Jumpers 1 5 1 User s Manual Clear CMOS CLRTC This jumper allows you to clear the Real Time Clock RTC RAM in CMOS You can clear the CMOS memory of date time and system setup parameters by erasing the CMOS RTC RAM data The onboard button cell battery powers the RAM data in CMOS which include system setup information such as system passwords To erase the RTC RAM Turn OFF the computer and unplug the power cord Remove the onboard battery Move the jumper cap from pins 1 2 default to pins 2 3 Keep the cap on pins 2 3 for about 5 10 seconds then move the cap back to pins 1 2 Re install the battery Plug the power cord and turn ON the computer Hold down the lt Del gt key during the boot process and enter BIOS setup to re enter 1 2 3 data
17. PCI IDE The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to active the primary secondary IDE interface Select Disabled to deactivate this interface The options Disabled Enabled User s Manual 2 2 4 2 Onboard Device Phoenix AwardBIOS CMOS Setup Utility Onboard Device Intel HD Audio Controller Auto ME Menu Level F5 Previous Values FT Setup Defaults Intel HD Audio Controller The options Auto Disabled ENX US15WP 1 gt Enter Select PU PD Value Fi0 Save ESC Exit Fl1 General Help 4 5 ENX US15WP 2 2 4 3 Onboard LAN Boot ROM The options Enabled Disabled 2 2 4 4 Power ON Function This feature allows you to wake up the system using any of the listed options The options Password Hot Key Mouse Left Mouse Right Any KEY Button Only Keyboard 98 2 2 4 5 Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports The choice Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto 2 2 46 PWRON After PWR fail The options are off on Former Sts 2 2 4 7 Watch Dog Timer Select This option will determine watch dog timer The choices Disabled 10 20 30 40 Sec 1 2 4 Min Phoenix AwardBIOS CMOS Setup Utility Integrated peripherals OnChip IDE Preece Fnterl Onboard De Onboard Lal Watch Dog timer Select Power ON
18. R2 GG LINE IN KBMS VGA USB12 LAN MIC IN LINE OUT ENX US15WP 15 ENX US15WP 1 3 1 Layout Content List 51015 Label Function Note Label Function Note CLRTC Clear CMOS 3 x 1 header pitch 2 54mm 21 JCOMPWR1 COM 1 RI 5V 12V Select 3 x 2 header pitch 2 54mm 22 JCOMPWR2 COM 2 RI 5V 12V Select 3 x 2 header pitch 2 00mm 22 Label Function Note RJ 45 Ethernet Connector 23 MIC_IN Microphone Port 23 LINE OUT Line out Port 23 Internal Connector Label Function Note CHA Chassis Fan Connector 3 1 wafer pitch 2 54mm 24 Serial Port Connector 1 5 x 2 header pitch 2 54mm 24 JLVDS LVDS Connector HIROSE DF13S 40DP 1 25V 28 LINE IN Line In Connector 5 X 1 header pitch 2 54mm 29 MATXPWR2 ATX Power Connector 3 x 2 header 29 USB34 USB 2 0 Connector 5 x 2 header pitch 2 54mm 30 16 User s Manual 1 4 System Memory 1 4 1 DIMM Sockets Location The motherboard comes with two 200 pin Double Data Rate 2 DDR2 SODIMM sockets A DDR2 module has the same physical dimensions as a DDR DIMM but has a 200 pin footprint compared to the 184 pin DDR DIMM DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket The following figure illustrates the location of the sockets TT TT E o pao mis kd Sam ENX US15WP 17 ENX
19. US15WP 5 ENX US15WP Packing List Before you begin installing your single board please make sure that the following materials have been shipped 1X ENX US15WP Nano ITX Main board 1 CD ROM contains the followings Users Manual in PDF file e Drivers e 1 Cable Kit 1x COM Cable w o Bracket 9P 2 00mm 1x IDE Cable 44P 44P e 1 MD6M to MD6F 2 Cable 1x ATX Power Cable 6P 20P 1x Startup Manual If of the above items is damaged or missing please contact your retailer User s Manual Revision History Revision Revision History Date V 1 00 First release for PCB 1 00 May 18 2009 1 01 Corrections of pin header pitch at 16 September 28 2009 V1 02 Correction of RJ45 LED status at Page 23 December 18 2009 1 03 Adjust Connectors direction of Pin 1 January 4 2010 1 04 Add internal COM port header May 1 2010 ENX US15WP 7 ENX US15WP Specifications Summary Intel Atom processor Z510P 1 1GHz Z530P 1 6GHz 400 533 MT s MHz FSB Intel System Controller Hub US15WP 1 200 pin SODIMM 2 DDR2 400 533 org x16 SDRAM Display 1 x By Chrontel CH7317 1 x LVDS m Realtek ALC 888 7 1 Channel High Definition Audio Codec udio co lay ALC 888VC Features LAN Realtek RTL 8111C Gigabit LAN gt 1 Mini PCle 1 x 4 x USB 2 x connectors 1 x pin header 1 x COM port w power header 1 x
20. a warning Enabled message to appear when anything attempts to access the boot sector or hard disk partition table Disabled No warning message will appear when anything attempts to access the boot sector or hard disk partition table 2 2 2 4 CPU L1 amp L2 amp L3 Cache Enabling this feature speeds up memory access Enabled Enable cache Disabled Disable cache AIV IIA PAIR Yall S1 AWD ENX US15WP 2 2 2 5 Quick Power On Self Test This allows the system to skip certain tests to speed up the boot up procedure Disabled Normal POST Enabled Enable quick POST 2 2 2 6 First Second Third Boot Device The BIOS tries to load the OS from the devices in the sequence set here The options are Hard Disk Hard Disk Device CDROM CDROM Device USB FDD USB Floppy Device USB ZIP USB ZIP Device USB CDROM USB CDROM Device Disabled Disabled any boot device 2 2 2 7 Boot Other Device Use this to boot another device The options Disabled Enabled 2 2 2 8 Security Option This category determines whether the password is required when the sys tem boots up or only when entering setup The options are The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt The system will boot but access to Setup will be denied if the correct password is not entered at the prompt To disable security select Set Supervisor Password at Main Menu and then you will be asked to
21. e main menu Take some time to familiarize yourself with the legend keys and their corresponding functions Practice navigating through the various menus and submenus If you accidentally make unwanted changes to any of the fields press F7 to load the Set up default values While moving around through the Setup program note that explanations appear in the Item Specific Help window located to the right of each menu This window displays the help text for the currently highlighted field ENX US15WP 33 ENX US15WP 2 2 BIOS Menu Screen When you enter the BIOS the following screen appears The BIOS menu screen displays the items that allow you to make changes to the system configuration To access the menu items press the up down right left arrow key on the keyboard until the desired item is highlighted then press Enter to open the specific menu Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features Esc Quit L lt Select 10 Save Exit Setup 34 User s Manual 2 2 1 Standard CMOS Features The Standard CMOS Features screen gives you an overview of the basic system Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Fri May 8 2009 Time hh mm ss 11 22 24 Menu Level p IDE Channel 0 Master IDE Channel 0 Slaver Change the internal clock Video EGA VGA Halt All errors Base Memory 639K Extended Memory 2086
22. ectrical shock hazard disconnect the power cable from the electrical outlet before relocating the system When adding or removing devices to or from the system ensure that the power cables for the devices are unplugged before the signal cables are connected If possible disconnect all power cables from the existing system before you add a device Before connecting or removing signal cables from the motherboard ensure that all power cables are unplugged Seek professional assistance before using an adapter or extension cord These devices could interrupt the grounding circuit Make sure that your power supply is set to the correct voltage in your area If you are not sure about the voltage of the electrical outlet you are using contact your local power company If the power supply is broken do not try to fix it by yourself Contact a qualified service technician or your retailer Operation safety Before installing the motherboard and adding devices on it carefully read all the manuals that came with the package Before using the product make sure all cables are correctly connected and the power cables are not damaged If you detect any damage contact your dealer immediately To avoid short circuits keep paper clips screws and staples away from connectors slots sockets and circuitry Avoid dust humidity and temperature extremes Do not place the product in any area where it may become wet Place the product on a stable surface
23. enter password Do not type anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely 40 User s Manual 2 2 3 Advanced Chipset Features Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD Item Help Menu Level p On Chip Frame Buffer Size Boot Type VBIOS Default LCD Panel Type 1024 768 generic Panel Scaling Auto Spread Spectrum Disabled 1 Enter Select PU PD Value 10 ESC Exit Fl1 General Help F5 Previous Values Setup Defaults DRAM default timings have been carefully chosen and should ONLY be changed if data is being lost Please first contact technical sup port 2 2 3 1 DRAM Timing Selectable This shows the DRAM timing value by SPD data or Manual 2 2 3 2 On Chip Frame Buffer Size The On Chip Frame Buffer Size can be set to 1 MB or 8 MB This memory is shared with the system memory 2 2 3 3 Boot The options VBIOS Default CRT LFP ENX US15WP 41 ENX US15WP 2 2 3 4 LCD Panel Type The options 640x480 generic 800x600 generic 1024 768 generic 640x480 NEC 8 4 800x480 NEC 9 1024x600 TMD 5 61 1024x600 Samsung 4 8 1024x768 Samsung 15 1024x768 Sharp 7 2 1280x800 Samsung 15 4 2 2 3 5 Panel Scaling The options Auto Force Off 2 2 3
24. nter gt The screen displays the following message Please lt Enter Password gt Press lt Enter gt If the CMOS is good and this option has been used to change the default password the user is asked for the password stored in the CMOS The screen displays the following message Confirm Password Type the current password and press Enter After pressing Enter ROM password or the current password user defined you can change the password stored in the CMOS The password must be no longer than eight 8 characters Remember to enable the password setting feature you must first select either Setup or System from the Advanced BIOS Features menu ENX US15WP 53 ENX US15WP 2 2 10 Save and Exit Setup If you select this and press lt Enter gt the values entered in the setup utilities will be recorded in the CMOS memory of the chipset The processor will check this every time you turn your system on and compare this to what it finds as it checks the system This record is required for the system to operate 54 Phoenix AwardBIOS CMOS Setup Utility Save amp Exit Setup SAVE to CMOS and EXIT Esc Quit 10 Save amp Exit Setup Save Data to CMOS User s Manual 2 2 11 Exit Without Saving Selecting this option and pressing lt Enter gt lets you exit the setup program without recording any new values or changing old ones Phoenix AwardBIOS CMOS Setup Utility Exit Withou
25. onochrome adapters 2 2 1 5 On Set the system to halt on errors according to the system functions specified in each option Configuration options All Errors No Errors All But Keyboard 36 2 2 2 Advanced BIOS Features User s Manual The Advanced BIOS Features screen appears when choosing the Advanced BIOS Features item from the Initial Setup Screen menu It allows the user to configure the motherboard according to his particular requirements Below are some major items that are provided in the Advanced BIOS Features screen A quick booting function is provided for your convenience Simply enable the Quick Booting item to save yourself valuable time Phoenix AwardBIOS CMOS Setup Utility CPU Feature Hard Disk Boot Priority Virus Warning CPU 11 5 12 Cache CDU 13 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up HumLock Status Security Option 1 Enter Select PU PD Value Fi Save ESC Exit F5 Previous Values Advanced BIOS Features Item Help Press Enter Disab led Enabled Enabled Enabled USB CDROM Hard Disk USB FDD Enabled Setup Menu Level General Help FT Setup Defaults ENX US15WP 3 7 ENX US15WP 2 2 2 1 CPU Features This item allows you to setup the CPU thermal management function Phoenix AwardBIOS CMOS Set
26. ow these steps to change the password 52 Choose the Set Supervisor Password option from the Initial Setup Screen menu and press lt Enter gt The screen displays the following message Please lt Enter Password gt Press lt Enter gt If the CMOS is good and this option has been used to change the default password the user is asked for the password stored in the CMOS The screen displays the following message Confirm Password Type the current password and press Enter After pressing Enter ROM password or the current password user defined you can change the password stored in the CMOS The password must be no longer than eight 8 characters Remember to enable the password setting feature you must first select either Setup or System from the Advanced BIOS Features menu User s Manual 2 2 9 Set User Password You can set user password It is able to enter change the options of setup menus Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Load Setup Defaults Advanced BIOS Features Set Supervisor Password Advanced Chipset Features Set User Password Integrated Peripherals Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Ese Quit Select 10 Save amp Exit Setup Change Set Disable Password Follow these steps to change the password Choose the Set User Password option from the Initial Setup Screen menu and press lt E
27. r a speaker In 4 channel 6 channel and 8 channel configuration the function of this port becomes Front Speaker Out ENX US15WP 23 ENX US15WP 1 6 2 Chassis Fan Connector Power Pin Sense 1 These are not jumpers DO NOT place jumper caps on the fan connectors 1 6 3 Serial Port Connector 1 2 COM1 COM2 RE DDTRE 24 User s Manual 1 6 4 System Panel Connector F PANEL This connector supports several chassis mounted functions PWR LED ran nm HD LED PWR LED GND PWR RESET Reset PWRSW GND NC DOHA Hoos System Power LED 2 pin PWRLED This 2 pin connector is for the system power LED Connect the chassis power LED cable to this connector The system power LED lights up when you turn on the system power and blinks when the system is in sleep mode ATX Power Button Soft off Button 2 pin PWRSW This connector is for the system power button Pressing the power button turns the system on or puts the system in sleep or soft off mode depending on the BIOS settings Pressing the power switch for more than four seconds while the system is ON turns the system OFF Hard Disk Drive Activity LED 2 pin HDLED This 2 pin connector is for the HDD Activity LED Connect the HDD Activity LED cable to this connector The IDE LED lights up or flashes when data is read from or written to the HDD Reset Button 2 pin RESET This 2 pin connec
28. rameters are also provided BIOS se ENX US15WP 31 ENX US15WP BIOS Setup 2 1 BIOS Setup Program This motherboard supports a programmable firmware chip that you can update using the provided utility Use the BIOS Setup program when you are installing a motherboard reconfiguring your system or prompted to Run Setup This section explains how to configure your system using this utility Even if you are not prompted to use the Setup program you can change the configuration of your computer in the future For example you can enable the security password feature or change the power management settings This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the firmware hub The firmware hub on the motherboard stores the Setup utility When you start up the computer the system provides you with the opportunity to run this program Press lt Del gt during the Power On Self Test POST to enter the Setup utility otherwise POST continues with its test routines If you wish to enter Setup after POST restart the system by pressing lt Ctrl Alt Delete gt or by pressing the reset button on the system chassis You can also restart by turning the system off and then back on Do this last option only if the first two failed The Setup program is designed to make it as easy to use as possible Being a menu driven program it lets you
29. t Saving Quit Without Saving Save amp Exit Setup Abandon all Data ENX US15WP 55
30. tor is for the chassis mounted reset button for system reboot without turning off the system power ENX US15WP 25 ENX US15WP 1 6 5 Primary EIDE Connector IDE UE unm 1 e Orient the red markings usually zigzag on IDE cable to 1 26 User s Manual 1 6 6 LCD Inverter Connector JBKL Signal Description For inverter with adjustable Backlight function it is possible to control the LCD brightness through the VR signal VOCS Vadj20 75V 4 25V Recommended 4 7 gt 1 16W ENBKL LCD backlight ON OFF control signal ENX US15WP 27 ENX US15WP 1 6 7 Digital UO Connector JDIO 1 6 8 28 Yer EI IILT WE GND DIO3 DIOT 0102 DIOG DIO1 0105 DIOO 0104 5 12V GND N Z GND LVDS1 CLEN NU A LYDSO CLKN LVDS SPAN Luten m KS GND aoa M GND LVDS1 N3 3 E LVDs1 LVDS1 P3 3d 2 E LVDSI P GND 9 GND LVDS1 d __ LVDS1 LVDS1 das G LYDS1 GND 2 E GND LVDSO_N3 LVDSO N2 Luten a j p LVDSO_P GND y e GND 1 050 es LYVDSO_NO LVDSO VDS PO d UN SC DDC x DOC 3 3V 5 333V User s Manual 1 6 9 Audio Line In Connector LINE IN vm vm mm GND 1 6 10 ATX Power
31. up Utility CPU Feature Delay Prior to Thermal 4 Min Limit CPUID MaxVal Disabled Menu Level p Execute Disable Bit Enabled Virtualization Technology Enabled 1 gt Enter Select PU PD Value 10 5 ESC Exit Fi General Help F5 Previous Values Setup Defaults Delay Prior to Thermal With the default value of 16 Minutes the BIOS activates the Thermal Monitor in automatic mode 16 minutes after the system starts booting up The options 4 Min 8 Min 16 Min 32 Min Limit CPUID MaxVal Sets Limit CPUID MaxVa1 to 3 This should be disabled for WinXP Execute Disabled Bit When disabled forces the XD feature flag to always return 0 Virtualization Technology When enabled a VMM can utilize the additional hardware capabilities provided by Vander pool Technology 2 2 2 2 Hard Disk Boot Priority set hard disk boot device priority Phoenix AwardBIOS CMOS Setup Utility Hard Disk Boot priority 1 Bootable Add in Cards Menu Level Use lt T gt or lt gt to select a device them press lt gt to move it up or lt gt move it down the list Press lt ESC gt to exit this menu 1 Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values Setup Defaults 2 2 2 3 Virus Warning Enables or disables the virus warning Activates automatically when the system boots up causing
Download Pdf Manuals
Related Search
ENX US15WP