0DVWHU 9LHZ 3OXV &38 6ZLWFK
Contents
1. MASTER VIEW PLUS 2 PU SWITCH USER S MANUAL CS 104 able of Contents Introduction Specifications Hardware Requirements Hardware Installation One Stage Installation Two Stage Installation Three Stage Installation Step by Step Hardware Installation Operation of the CS 104 Front Panel Selection Keyboard Selection Auto Scan Mode Previous Next Mode Direct Port Selection LED Display DIP Switch Settings Foot Switch Optional Troubleshooting Preventing Radio amp TV Interference Limited Warranty MCOONNNDOOHKR A HWW W Packaging Checklist e 1 Master View CPU Switch CS 104 e 1 Power Adapter DC 9V 250mA minimum e 1 CPU Switch User s Manual This Book Copyright 1996 ATEN International Co Ltd Manual Part No PAPE 0126 200 Introduction Master View is a controller for that will allow one user to access multiple computers Before the costly network was the only solution for this application Now the Master View provides the easiest and the most cost effective way of accessing multiple computers With the powerful features of Master View anyone is capable of operating or testing many computers with one of each a monitor a keyboard and a mouse Switching from one computer to another is accomplished quickly and easily either by using Hot Keys or pressing a button on the Master View No additional programs to install and no problems with compatability because the Master View intercepts the Hot2. CS 104 DIP switch 4 to ON Turn all other CS 104s switches OFF Check the PORT STATUS LEDs for a flash pattern Or Press the space bar to exit these modes before giving Hot Key Commands Manually change the port selection using the SELECT BUT TON S to a com puter in the power on state Unplug the keyboard then reconnect the keyboard Turn off all CS 104s wait for 5 seconds and turn them on Try presing a single key at a time CTRL ALT SHIFT Port Number then EN TER Both Serial and PS 2 mice must be used if using AT and PS 2 style computers NT System must be selected at startup for NT to detect the mouse Port light lit while NT loading Add a DC 9V power adaptor to the first stage CS 104 PREVENTING RADIO amp TV INTERFERENCE WARNING This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications This equipment has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interfer ence when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures LIMITED WARRANTY IN
3. 3Seconds OFF ON xX ON 10Seconds ON or x ON 20Seconds OFF orr X ON 40Seconds The DIP Switch settings for the second and third stage CS104s are all switches off Foot Switch Optional FUNCTION The Foot Switch is an extension of the front panel Push Button both have the same function Each time the Foot Switch is stepped on a different computer is selected Foot Switch part 2X 001 Large 2X 002 Small CONNECTION The Foot Switch is connected to the CS 104 through a RJ 11 phone jack which is located on one side of the unit If you plan to install an ON OFF switch to work with the Push Button check the diagram to the right to ensure correct switch connection 123456 Troubleshooting Symptom Possible Causes What to do The first stage CS 104 unit will not take Hot Key commands Pressing the Hot Keys get no response Mouse is not responding or be ing detected The CS 104 does not work properly Incorrect DIP switch settings The CS 104 is oper ating in either Auto Scan or Previous Next mode The selected port connects to a power off com puter Improper keyboard reset Improper CS 104 reset Incorrectly pressing hot keys AT Serial Mouse and PS 2 style com puters being used with CS 104 If using NT system and Serial Number begins with a letter D C B or A The CS 104 can not get enough power from the CPUs Set the first stage
4. Keys directly from the keyboard One Master View unit will control up to four computers When used together or cascaded the Master View can control up to 64 computers A powerful auto scan feature scans all operational computers one at a time and will stop upon the users request Master View is ideal for Server Control Room Testing etc Features Supports PS 2 Keyboard or AT Keyboard Supports PS 2 Mouse or Serial Mouse Supports VGA SVGA and Multisync Monitors Simple keystrokes or push button selection of active PC Buzzer Sound for Switching Confirmation Cascade to a depth of three units Auto Scan and Manual Selection Keyboard Caps Lock Num Lock and Scroll Lock states automatically saved and restored when switching between computers e Scan mode automatically switches through active computers this scan rate is controlled by DIP switch selections Saves space equipment and power costs Easy Hot Key control is compatible with normal keyboard operation Specifications Specification DC 9V 250 mA max Keyboard Button 1 Ready LED 4 Port Status LEDs 3 10 20 and 40 Seconds Selectable 5 pin DIN AT and 6 pin mini DIN PS 2 9 pin D Type Male Female 6 pin mini DIN Female 15 pin D Type Female Male Metal 2650g Dimensions L x W x H 254 x 180 x 82 mm Hardware Requirements You will need to have the following To connect to a Monitor e A VGA SVGA or Multisync monitor card installed in
5. NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAM AGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and specially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquires please contact your direct
6. each PC e One VGA SVGA or Multisync Monitor To connect a Mouse e DB 9 serial port or 6 pin mini DIN PS 2 bus mouse port in each PC e One PS 2 mouse and or a DB 9 Serial Mouse To connect a Keyboard e 5 pin DIN AT keyboard port with 5V DC on pin 5 and ground on pin 4 or a 6 pin mini DIN PS 2 keyboard port with 5V DC on pin 4 and ground on pin 3 e One PS 2 style Keyboard or one AT style Keyboard Hardware Installation The CS 104 is cascadable up to a depth of 3 stages which is selected by DIP switch settings One Stage In a one stage system a single CS 104 can control up to four computers The DIP switch 4 is set to the ON position Connect the monitor output mouse port and the keyboard port of a computer to one of the CS 104 s available PC port groups with the appropriate cables The 5 pin DIN is for an AT style PC key board and the 6 pin mini DIN is for a PS 2 style keyboard You can use either port for each computer Keyboard Video Mouse Fig 1 A One Stage installation of the CS 104 Two Stage In a two stage system the CS 104 can either control PC s directly or it can control other CS 104 s second stage units or a combination of both In this configuration the maximum number of computers that can be in the system is 16 The DIP switch 4 on the first stage unit The CS 104 directly connected to the monitor mouse and keyboard is placed in the ON position All other CS 104 units have DIP switch 4 in
7. he Fig 3 A Three Stage installation of the CS 104 Step by Step Hardware Installation Setting up one CS 104 The connection of the Keyboard Video and the Mouse is accomplished by using the same cables that you would use to connect them to a PC Connecting the mouse e Ifyou are using a PS 2 style mouse connect the 6 pin mini DIN male plug of the PS 2 mouse to the female PS 2 port located in the CONSOLE section on the back of the CS 104 e Ifyou are using a Serial mouse you must connect the DB 9 Serial connector of the mouse to the DB 9 Serial Port of the CS 104 e NOTE If the computers attaced to the CPU ports have mixed mouse types ie Serial and PS 2 you must connect BOTH mice to the console port Connecting the keyboard e If your keyboard uses a 5 pin DIN AT style connector plug the male 5 pin DIN connector into the female 5 pin DIN socket in the CONSOLE section of the CS 104 OR e If your keyboard uses a 6 pin mini DIN PS 2 style connector plug the male 6 pin mini DIN connector into the 6 pin mini DIN socket in the CONSOLE section of the CS 104 3 Connecting the monitor e Using the cable attached to your monitor plug the male high density DB 15 standard VGA SVGA or Multisync connector into the female high density DB 15 connector in the CONSOLE section of the CS 104 Connecting a computer e Connect a VGA compatible monitor extension cable from the video card of the computer to the video connecto
8. ns all connected computers that are in a power on state one by one from the first computer in the first stage to the last computer in the last stage Alt Ctrl Shift 0 Enter To stop Auto Scan mode Space To start the Previous Next mode This mode selects from all connected computers that are in a power on state one by one from the first computer in the first stage to the last computer in the last stage Alt Ctrl Shift 9 Enter To select the previous port Left Shift To select the next port right Shift To stop the Previous Next mode Space To select a first stage port directly Alt Ctrl Shift Enter is the number of the first stage port To select a second stage port directly Alt Ctrl Shift Enter The 1 selects the number of a first stage port The 2 selects the number of a second stage port To select a third stage port directly Alt Ctrl Shift Enter The 1 selects the number of a first stage port The 2 selects the number of a second stage port The 3 selects the number of a third stage port NOTE is a numerical digit between 1 and 4 Actions Taken by the CS 104 Result for correct Hot Key Incorrect Hot Keys e Filters out Hot Keys and beeps once Displays incorrect keystrokes e Scans powered on computers one by one and flashes corresponding LED Scan rate is set by the DIP switches of the firs
9. r in one of the PC sections of the CS 104 e Connect a straight through keyboard from the keyboard port of your computer to the keyboard port of the same PC section where you connected the video e Connect a straight through PS 2 or Serial mouse extension cable from the mouse connection of your PC to Operation of the CS 104 You may access any computer by pressing the front panel SELECT BUTTON or through keyboard com mands After selecting the computer you wish to control the CS 104 directs the keyboard control mouse control and video image of the computer you have selected as if the computer were right next to you Selection from the front panel button To select a computer connecting to a CS 104 unit you simply press the front panel SELECT BUTTON of that unit several times until the computer that you wish to select is indicated by the corresponding indicator LED being turned on For a computer in the second stage of a Two Stage system you will have to make your selection on the CS 104 unit directly connected to the PC you wish to use Similarly in a Three Stage system you will need to make your selection on the CS 104 unit directly connected to the computer in the third stage Selection from the keyboard As shown below first pressing the Alt Ctrl and Shift keys to enable the Hot Key commands You then enter the command keystrokes and complete the command by hitting the Enter key To start the Auto Scan mode This mode sca
10. t stage CS 104 Space stops this mode Previous Next e Filters out Hot Keys and beeps once Displays incorrect keystrokes The right Shift key selects the next higher numbered computer The eft Shift selects the next lower num bered computer Space stops this mode Filters out Hot Keys and beeps once for a Displays incorrect keystrokes ready port otherwise beeps twice LED Display There is one MANUAL LED and four PORT STATUS LEDs on the front panel The functions of these LEDs are as follows MANUAL LED This LED turns on when the CS 104 is in MANUAL mode PORT STATUS LED These four 4 LEDs are used to indicate the various status conditions for any given port 1 If a port is not selected its corresponding PORT STATUS LED will be off 2 If a port is selected that is connected to another CS 104 its corresponding PORT STATUS LED will flash 3 If a port is selected that is connected to a power on computer its corresponding PORT STATUS LED will remain lit 4 If a port is selected that is connected to a power on computer while in Previous Next mode its corresponding PORT STATUS LED will flash 5 If a port is selected that is connected to a power on computer while in the Auto Scan mode its corresponding PORT STATUS LED will flash LED On LED Off DIP Switch Settings The Following DIP Switch settings are for the first stage CS 104 ONLY DIP Switch Number ON ON x ON
11. the OFF position Computers may now be connected either to the first stage CS 104 or the second stage units The 5 pin DIN is for an AT style PC keyboard and the 6 pin mini DIN is for a PS 2 style keyboard You can use either port for each computer Keyboard Video Mouse z 7 a Second Stage CS 104 e Use AT style 5 pin DIN Keyboard connector m e Set DIP Switch 4 to the OFF Position Fig 2 A Two Stage installation of the CS 104 Three Stages Similar to a Two Stage configuration more computers can be controlled by adding another layer of CS 104 units In a three stage system the maximum number of computers that can be controlled is increased to 64 The DIP switch 4 on the first stage unit The CS 104 directly connected to the monitor mouse and keyboard is placed in the ON position All other CS 104 units have DIP switch 4 in the OFF posi tion Computers may now be connected to the first stage CS 104 the second stage units or the thirrd stage units The 5 pin DIN is for an AT style PC keyboard and the 6 pin mini DIN is for a PS 2 style key board You can use either port for each computer NOTE To connect the keyboard ports of the second or Keyboard Video Mouse ErP i we Second Stage CS 104 e Use AT style 5 pin DIN Keyboard connector roe m e Set DIP Switch 4 to the OFF Position nn Third Stage CS 104 e Use AT style 5 pin DIN _ a a Keyboard connector E e F e Set DIP Switch 4 to t
Download Pdf Manuals
Related Search