E35LM1 R2.0
Contents
1. System Panel Header PLED This header accommodates PLED 9 pin PANEL1 PRE several system front panel see p 12 No 8 functions DUMMY RESET GND HDLED A HDLED Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart 21 PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 sleep state The LED is off when the system is in S3 S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assign2. 38 3 4 5 Super lO Configuration ASRock UEFI setup utility mai i Wed 10 17 2012 15 17 59 Serial Port Use this item to enable or disable the onboard serial port Serial Port Address Use this item to set the address for the onboard serial port Configuration options 3F8h IRQ4 and 3E8h IRQ4 CIR Controller Use this item to enable or disable CIR controller The default value is Disabled 39 3 4 6 ACPI Configuration ASRock UEFI setup Utility Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it Check Ready Bit Use this item to enable or disable the feature Check Ready Bit ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this motherboard to submit Windows certification PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode Onboard LAN Power On Use this item to enable or disable Onboard LAN to turn on the system from the power soft off mode Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system USB Keyboard Remote Power On Use this item to enable or di
3. 3 4 3 South Bridge Configuration ASRock UEFI setup Utility 4 Onboard HD Audio Select Enabled or Disabled for the onboard HD Audio feature The de fault value is Enabled Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel Onboard LAN This allows you to enable or disable the Onboard LAN feature Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Good Night LED Use this item to enable or disable Power LED and LAN LED 37 3 4 4 Storage Configuration ASRock UEFI setup Utility SATA Controller Use this to enable or disable SATA controller The default value is Enabled SATA Mode Use this to select SATA mode Configuration options IDE Mode and AHCI Mode The default value is AHCI Mode 4 AHCI Advanced Host Controller Interface supports NCQ and other new features that will improve SATA disk perfor mance but IDE mode does not have these advantages SATA Aggressive Link Power Management Use this item to configure SATA Aggressive Link Power Management Hard Disk S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analy sis and Reporting Technology feature Configuration options Disabled and Enabled
4. 34 3 4 1 CPU Configuration ASRock UEFI setup Utility Cool n Quiet Use this item to enable or disable AMD s Cool n Quiet technology The default value is Enabled Configuration options Auto Enabled and Disabled If you install Windows 8 7 Vista and want to enable this function please set this item to Enabled Please note that enabling this function may reduce CPU voltage and memory frequency and lead to system stability or compatibility issue with some memory modules or power supplies Please set this item to Disable if above issue occurs SVM Mode Use this to enable or disable SVM Secure Virtual Machine architecture When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by AMD V Configuration options Enabled and Disabled The default value is Enabled C6 Mode Use this to enable or disable CPU C6 state The default value is Disabled 35 3 4 2 North Bridge Configuration ASRock UEFI setup Utility KK Z ool H H Monitor PCI Express Wed 10 17 2012 15 17 45 Primary Graphics Adapter This item allows you to select the type of Primary VGA in case of multiple video controllers The default value of this feature is PCI Express Cofiguration options Onboard and PCI Express Share Memory This allows you to set onboard VGA share memory feature The default value is Auto 36
5. E35LM1 R2 0 User Manual Version 1 0 Published October 2012 Copyright 2012 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of the poss
6. m ith A Sao k 8 gt H H Monitor oot Security Description Configuration DRAM Frequency Wed 10 17 2012 15 17 29 DRAM Timing Configuration DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automatically DRAM Timing Control ASRock UEFI setup Utility H W Monitor i Description oy Disabled e duto nable or disable DDR3 power down Auto Auto Auto Auto Wed 10 17 2012 15 17 34 Power Saving Mode Use this to enable or disable Power Saving Mode The default value is Disabled Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node or accross nodes decreasing access contention 31 CAS Latency tCL Use this item to change CAS Latency tCL Auto Manual setting The default is Auto RAS to CAS Delay tRCD Use this item to change RAS to CAS Delay tRCD Auto Manual setting The default is Auto Row Precharge Time tRP Use this item to change Row Precharge Time tRP Auto Manual setting The default is Auto RAS Active Time tRAS Use this item to change RAS Active Time tRAS Auto Manual setting The default is Auto Command Rate CR Use this item to change Command Rate CR Auto Manual setting Min 1N Max 2N The default is Auto RAS Cycle Time tRC Use this item to change RAS Cycle Time tRC Auto Manual setting The default i
7. 1 x CIR header 1 x COM port header 1 x Chassis Intrusion header 1 x CPU Fan connector 3 pin 2 x Chassis Fan connectors 1 x 4 pin 1 x 3 pin 24 pin ATX power connector Front panel audio connector me 2 x USB 2 0 headers support 4 USB 2 0 ports BIOS Feature 32Mb AMI UEFI Legal BIOS with GUI support Supports Plug and Play ACPI 1 1 Compliance Wake Up Events Supports jumperfree SMBIOS 2 3 1 Support DRAM FCH 1V 1 8V Voltage Multi adjustment Support CD Drivers Utilities AntiVirus Software Trial Version CyberLink MediaEspresso 6 5 Trial ASRock MAGIX Multimedia Suite OEM Google Chrome Browser and Toolbar Hardware CPU Temperature Sensing Monitor Chassis Temperature Sensing CPU Fan Tachometer Chassis Fan Tachometer CPU Quiet Fan Allow Chassis Fan Speed Auto Adjust by CPU Temperature CPU Chassis Fan Multi Speed Control CASE OPEN detection Voltage Monitoring 12V 5V 3 3V CPU Vcore Microsoft Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit compliant see CAUTION 2 Certifications FCC CE WHQL ErP EuP Ready ErP EuP ready power supply is required For detailed product information please visit our website http www asrock com WARNING Please realize that there is a certain risk involved with overclocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using third party overc
8. Mouse Port Purple Green 5 Front Speaker Lime 2 VGA Port 6 Microphone Pink 3 LAN RJ 45 Port 7 USB2 0 Ports USB45 4 Line In Light Blue 8 USB 2 0 Ports USB01 There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications LAN Port LED Indications Activity Link LED SPEED LED Description No Link Off 10Mbps connection ACT LINK SPEED LED LED mM Data Activity Orange 100Mbps connection Onn L Green 1Gbps connection LAN Port To enable Multi Streaming function you need to connect a front panel audio cable to the front panel audio header Please refer to below steps for the software setting of Multi Streaming For Windows XP After restarting your computer you will find Mixer tool on your system Please select Mixer ToolBox click Enable playback multi streaming and click ok Choose 2CH or 4CH and then you are allowed to select Realtek HDA Primary output to use Rear Speaker and Front Speaker or select Realtek HDA Audio 2nd output to use front panel audio Then reboot your system For Windows 8 7 I Vista After restarting your computer please double click Realtek HD Audio Manager on the system tray Set Speaker Configuration to Quadraphonic or Stereo Click Device advanced settings choose Make front and rear output devices playbacks two different audio streams simultaneously
9. On Chassis Fan 1 Setting This allows you to set the chassis fan 1 speed Configuration options Full On and Manual Mode The default is value Full On Chassis Fan 2 Setting This allows you to set the chassis fan 2 speed Configuration options Full On and Manual Mode The default is value Full On Case Open Feature This allows you to enable or disable case open detection feature The default is value Enabled Clear Status This option appears only when the case open has been detected Use this option to keep or clear the record of previous chassis intrusion status 45 3 7 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority ASRock UEFI setup Utility eae lias S FN FN Main Advanced Va OC Tweaker Fast Boot Fast Boot minimizes your computer s boot time There are three con figuration options Disabled Fast and Ultra Fast The default value is Disabled Please refer to below descriptions for the details of these three options Disabled Disable Fast Boot Fast The only restriction is you may not boot by using an USB flash drive Ultra Fast There are a few restrictions 1 Only supports Windows 8 UEFI operating system 2 You will not be able to enter BIOS Setup Clear CMOS or run utility in Widows to enter BIOS Setup 3 If you are using an external graphics card the VBIOS must support U
10. headers on this motherboard Each USB 2 0 header can support two USB 2 0 ports USB 2 0 Headers 9 pin USB6 7 see p 12 No 20 9 pin USB8_ 9 see p 12 No 19 Consumer Infrared Module Header This header can be used to 4 pin CIR1 connect the remote GNC see p 12 No 18 IRRX controller receiver ATX 5VSB 20 Front Panel Audio Header N This is an interface for front PRESENCE 9 pin HD_AUDIO1 MIC_RET panel audio cable that allows see p 12 No 21 A OUT_RET convenient connection and 1 control of audio devices OUT2_L J_SENSE OUT2 R MIC2 R MIC2 L 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction in our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic IN MIC to MIC2 L B Connect Audio R RIN to OUT2_R and Audio L LIN to OUT2 L C Connect Ground GND to Ground GND D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic For Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit OS Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume
11. ments are matched correctly Chassis Speaker Header 4 pin SPEAKER 1 see p 12 No 15 SPEAKER DUMMY DUMMY 5V Chassis Fan Connectors 4 pin CHA_FAN1 CHA_FAN_SPEED 12V see p 12 No 2 GN 2V FAN_SPEED_CONTROL 3 pin CHA_FAN2 GND see p 12 No 16 12V CHA FAN SPEED CPU Fan Connectors 3 pin CPU FAN1 CPU FAN SPEED 12V see p 12 No 1 GND ATX Power Connector 12 24 24 pin ATXPWR1 see p 12 No 7 22 Please connect the chassis speaker to this header Please connect the fan cables to the fan connectors and match the black wire to the ground pin CHA FAN2 supports fan speed control by fan power voltage Please connect the CPU fan cable to the connector and match the black wire to the ground pin CPU FAN1 supports fan speed control Please connect an ATX power supply to this connector 4 Though this motherboard provides 24 pin ATX power connector 26 it can still work if you adopt a traditional 20 pin ATX power supply To use the 20 pin ATX power supply please plug your power supply along with Pin 1 and Pin 13 20 Pin ATX Power Supply Installation 1 Serial port Header 9 pin COM1 This COM1 header supports a serial port module see p 12 No 22 Chassis Intrusion Header This motherboard supports 2 pin Cl1 l CASE OPEN detection feature GND see p 12 No 14 Signal that detects if the chas
12. read below operation guide of Hot Plug feature carefully Before you process the SATA3 HDD Hot Plug please check below cable accessories from the motherboard gift box pack A 7 pin SATA data cable B SATA power cable with SATA 15 pin power connector interface A SATA data cable Red B SATA power cable SATA 7 pin The SATA 15 pin power 1x4 pin conventional connector Black connect power connector White to SATA3 HDD connect to power supply Caution 1 Without SATA 15 pin power connector interface the SATA3 Hot Plug cannot be processed 2 Even some SATA3 HDDs provide both SATA 15 pin power connector and IDE 1x4 pin conventional power connector interfaces the IDE 1x4 pin conventional power connector interface is definitely not able to support Hot Plug and will cause the HDD damage and data loss Points of attention before you process the Hot Plug 1 Below operation procedure is designed only for our motherboard which supports SATA3 HDD Hot Plug The SATA3 Hot Plug feature might not be supported by the chipset because of its limitation the SATA3 Hot Plug support information of our motherboard is indicated in the product spec on our website www asrock com 2 Make sure your SATA3 HDD can support Hot Plug function from your dealer or HDD user manual The SATA3 HDD which cannot support Hot Plug function will be damaged under the Hot Plug operation 3 Please make sure the SATA3 driver is installed into system properly The
13. the bottom of driver list 17 3 CIR sensors in different angles le Only one of the front USB port can support CIR function When the CIR function is enabled the other port will remain USB function 2 Multi Angle CIR Receiver is used for front USB only Please do not use the rear USB bracket to connect it on the rear panel Multi Angle CIR Receiver can receive the multi direction infrared signals top down and front which is compatible with most of the chassis on the market 3 The Multi Angle CIR Receiver does not support Hot Plug function Please install it before you boot the system ASRock Smart Remote is only supported by some of ASRock motherboards Please refer to ASRock website for the motherboard support list http www asrock com 18 2 6 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap Vy is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose Nis Sed pint and pin2 are Short when jumper cap Short Open is placed on these 2 pins Jumper Setting Description Clear CMOS Jumper 12 2 3 Oo comm see p 12 No 6 Default Clear CMOS Note CLRCMOS1 allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap t
14. 2 12 Installing Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions If you want to install Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit OS on your SATA3 HDDs without RAID functions please follow below procedures according to the OS you install 2 12 1 Installing Windows XP XP 64 bit Without RAID Functions If you want to install Windows XP XP 64 bit OS on your SATA3 HDDs without RAID functions please follow below steps 4 AHCI mode is not supported under Windows XP XP 64 bit OS Using SATA3 HDDs without NCQ function STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode to IDE STEP 2 Install Windows XP XP 64 bit OS on your system 27 2 12 2 Installing Windows 8 8 64 bit 7 I 7 64 bit I Vista Vista 64 bit Without RAID Functions If you want to install Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit OS on your SATA3 HDDs without RAID functions please follow below steps Using SATA3 HDDs with NCQ function STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode to AHCI STEP 2 Install Windows 8 8 64 bit 7 I 7 64 bit Vista Vista 64 bit OS on your system Using STA3 HDDs without NCQ function STEP 1 Set up
15. EFI GOP in order to boot Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65535 0xFFFF means indefi nite waiting Bootup Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up 46 Full Screen Logo Use this item to enable or disable OEM Logo The default value is En abled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots please select Enabled Configuration options Enabled and Disabled The default value is Enabled Boot Failure Guard Enable or disable the feature of Boot Failure Guard Boot Failure Guard Count Enable or disable the feature of Boot Failure Guard Count 47 3 8 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it ASRock UEFI setup Utility Disabled Secure Boot Use this to enable or disable Secure Boot The default value is Disabled 48 3 9 Exit Screen ASRock UEFI setup Utility Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the UEFI SETUP UTILIT
16. UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode to IDE STEP 2 Install Windows 8 8 64 bit 7 I 7 64 bit Vista Vista 64 bit OS on your system 28 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the UEFI SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information OC Tweaker To set up overclocking features Advanced To set up the advanced UEFI features Tool Useful tools H W Monitor To display current hardware status Boot To set up the default system device to locate and load
17. Y Discard Changes and Exit When you select this option it will pop out the following message Discard changes and exit setup Select OK to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Discard changes Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this operation 49 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to dis play the menus 4 22 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects in
18. and PPPOE UEFI Download Server Use this item to select UEFI firmware download server for Internet Flash Configuration options Asia Europe USA and China Dehumidifier Function Users may prevent motherboard damages due to dampness by enabling Dehumidifier Function When enabling Dehumidifier Function the com puter will power on automatically to dehumidify the system after entering S4 S5 state Dehumidifier Period This allows users to configure the period of time until the computer powers on and enables Dehumidifier after entering S4 S5 state Dehumidifier Duration This allows users to configure the duration of the dehumidifying process before it returns to S4 S5 state Dehumidifier CPU Fan Setting Use this setting to configure CPU fan speed while Dehumidifier is en abled Would you like to save current setting user defaults In this option you are allowed to load and save three user defaults according to your own requirements 44 3 6 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage ASRock UEFI setup Utility Te gt PA b a OC Tweaker Advanced CPU Fan Setting This allows you to set the CPU fan speed Configuration options Full On and Automatic Mode The default is value Full
19. and click ok Then reboot your system 13 Chapter 2 Installation This is a Mini ITX form factor motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Make sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard components 2 1 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis 4 Do not over tighten the screws Doing so may damage the motherboard 2 2 Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded antistatic pad or in the bag that comes with the component switched off or the power cord is detached from the power supply Failure to do So may cause severe damage to the motherboard peripherals and or components 4 Before you install or remove any comp
20. ibility of such damages arising from any defect or error in the manual or product FC This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents 1 introduction a a na 5 1 1 Package Contents vuymeeessemmsunaerestdmeed nn 5 12 HENAN 6 1 3 Unique Features iacccdccancarentnccesascdsneneescecnereusseutonenadeedeniaces 9 1 4 Motherboard Lay OWE intasicconvievrerdiunncdniasinnciueawanateenntivauae 12 13 VO Panel sranie iE 13 2 ANS ON 14 2 1 STEN OES ua 14 2 2 Pre installation Precautions rrrrnnrnnnnnrnnnnnennnnnnnnnnre 14 2 3 Installation of Memory Modules DIMM 15 2 4 Expansion Slot PCI Express Slot 16 2 5 ASRock Smart Remote Installation Guide 17 26 Jumpers Setup nid 19 2 7 O
21. ing You can watch Youtube HD videos and download si multaneously Real Time Analysis of Your Data With the status window you can easily recognize which data streams you are transferring currently ASRock XFast RAM ASRock XFast RAM fully utilizes the memory space that cannot be used under Windows OS 32 bit CPU ASRock XFast RAM shortens the loading time of previously visited websites mak ing web surfing faster than ever And it also boosts the speed of Adobe Photoshop 5 times faster Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan ASRock Crashless BIOS ASRock Crashless BIOS allows users to update their BIOS without fear of failing If power loss occurs during the BIOS up date process ASRock Crashless BIOS will automatically finish the BIOS update procedure after regaining power Please note that BIOS files need to be placed in the root directory of your USB disk Only USB2 0 ports support this feature ASRock OMG Online Management Guard Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG You may schedule the starting and ending hours of internet access granted to other users In order to prevent users from bypassing OMG guest accounts without permission to modify the system time are re quired 10 ASRock Internet Flash ASRock Internet Flash searches for available UEFI firmware u
22. latest SATA3 driver is available on our support website www asrock com 4 Make sure to use the SATA power cable amp data cable which are from our motherboard package 5 Please follow below instructions step by step to reduce the risk of HDD crash or data loss 25 How to Hot Plug a SATA3 HDD Points of attention before you process the Hot Plug Please do follow below instruction sequence to process the Hot Plug improper procedure will cause the SATA3 HDD damage and data loss SCA Please connect SATA power cable 1x4 pin Sieg Connect SATA data cable to end White to the power supply 1x4 pin the motherboard s SATAII SATA3 cable connector SE Connect SATA 15 pin power cable SC Connect SATA data cable to the connector Black end to SATA3 HDD SATA3 HDD gt How to Hot Unplug a SATA3 HDD Points of attention before you process the Hot Unplug Please do follow below instruction sequence to process the Hot Unplug improper procedure will cause the SATA3 HDD damage and data loss Unplug SATA data cable from SATA3 HDD side 26 2 11 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive first Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from up to bottom side to install those required drivers Therefore the drivers you install can work properly
23. locking tools Overclocking may affect your system s stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION 1 Due to the operating system limitation the actual memory size may be less than 4GB for the reservation for system usage un der Windows 8 7 Vista XP For Windows OS with 64 bit CPU there is no such limitation 2 ASRock XFast RAM is not supported by Microsoft Windows XP 64 bit 1 3 Unique Features ASRock Instant Boot ASRock Instant Boot allows you to turn on your PC in just a few seconds provides a much more efficient way to save energy time money and improves system running speed for your sys tem It leverages the S3 and S4 ACPI features which normally enable the Sleep Standby and Hibernation modes in Windows to shorten boot up time By calling S3 and S4 at specific timing during the shutdown and startup process Instant Boot allows you to enter your Windows desktop in a few seconds ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS DOS or Windows With this utility you can press the lt F6 gt key during the POST or the lt F2 gt key to enter into the BIOS setup menu to access ASRock Instant Fla
24. nboard Headers and Connectors ccseeeeeeeeeee sees 20 2 8 Serial ATA3 SATA3 Hard Disks Installation 24 2 9 Hot Plug and Hot Swap Functions for SATA3 HDDs 24 2 10 SATA3 HDD Hot Plug Feature and Operation Guide 25 2 11 Driver Installation Guide resrrnnvrnnrrnnrrnvrnvrrnnnrnvrnnnnnnn 27 2 12 Installing Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions 27 2 12 1 Installing Windows XP XP 64 bit Without RAID FIN ccctacaucaentanintousance une aaresmcaunede oo 27 2 12 2 Installing Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit Without RAID Functions 28 3 UEFI SETUP UTILITY 2 29 TYNN 29 3 1 1 UEFI Menu BOF ane inni 29 312 Navigation KEY man 30 3 2 Main SEE ete 30 3 3 OC Tweaker Screen naissent ientesstes 31 3 4 Advanced Screen 34 3 4 1 CPU Configuration 2 2 35 3 4 2 North Bridge Configuration 36 3 4 3 South Bridge Configuration 37 3 4 4 Storage Configuration 38 3 4 5 Super IO Configuration 39 3 4 6 ACPI Configuration 40 3 4 7 USB Configuration sesssasrdanen berede 42 0 Te 43 3 6 Hardware Health Event Monitoring Screen 45 3 7 Boot STEN ete 46 3 8 SE SEN See 48 3 9 PSN 49 4 Software Support rnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnr 50 4 1 Install Operating System 50 4 2 Suppor
25. nstallation Guide ASRock E35LM1 R2 0 Support CD 2 x Serial ATA SATA Data Cables Optional 1 x I O Panel Shield FN y iS Q ASRock Reminds You To get better performance in Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit it is recommended to set the BIOS option in Storage Con figuration to AHCI mode 1 2 Specifications Platform Mini ITX Form Factor AMD Zacate E 240 APU Supports AMD s Cool n Quiet Technology UMI 2 5 GT s AMD A50M Chipset 2 x DDR3 DIMM slots Supports DDR3 1333 0C 1066 800 non ECC un buffered Max capacity of system memory 16GB see CAUTION 1 Expansion Slot 1x PCI Express 2 0 x16 slot PCIE1 x4 mode Integrated AMD Radeon HD 6310 graphics DX11 class iGPU Pixel Shader 5 0 Max shared memory 512MB Supports D Sub with max resolution up to 2560x1600 60Hz 5 1 CH HD Audio Realtek ALC662 Audio Codec PCIE x1 Gigabit LAN 10 100 1000 Mb s Realtek RTL8111E Supports Wake On LAN Supports LAN Cable Detection Supports Energy Efficient Ethernet 802 3az Supports PXE Rear Panel I O I O Panel 1 x PS 2 Keyboard Mouse Port 1 x VGA Port 4 x Ready to Use USB 2 0 Ports 1 x RJ 45 LAN Port with LED ACT LINK LED and SPEED LED HD Audio Jack Line in Front Speaker Microphone SATA3 4 x SATA3 6 0 Gb s connectors support NCQ AHCI and Hot Plug functions Connector 4 x SATA3 6 0Gb s connectors
26. o short pin2 and pin3 on CLRCMOS for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS ac tion Please be noted that the password date time user default profile 1394 GUID and MAC address will be cleared only if the CMOS battery is removed the BIOS option Clear Status to clear the record of previous chassis intrusion status 4 If you clear the CMOS the case open may be detected Please adjust 19 2 7 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard Serial ATA3 Connectors These four Serial ATA3 SATA3 A SATA3_1 see p 12 No 12 2 x connectors support SATA data SATA3_2 see p 12 No 10 lt Ly IL q cables for internal storage SATA3_3 see p 12 No 11 FE devices The current SATA3 SATA3 4 see p 12 No 9 A cg interface allows up to 6 0 Gb s 3 LL 3 data transfer rate Serial ATA SATA Either end of the SATA data Data Cable cable can be connected to the Optional SATA SATA2 SATA3 hard disk or the SATA2 SATA3 connector on this motherboard Besides four default USB 2 0 ports on the I O panel there are two USB 2 0
27. ock Good Night LED ASRock Good Night LED technology can offer you a better en vironment by extinguishing the unessential LED By enabling Good Night LED in BIOS the Power HDD LAN LED will be switched off when system is on Not only this Good night LED will automatically switch off Power and Keyboard LED when the system enters into Standby Hibernation mode as well 11 1 4 Motherboard Layout 1 2 34 5 mu Nu x GRE 6 z AE T MAS HER elle lt AJI X A 2 ae JE 2 LE 2 Z Q Se 7 m lt lt x 5 X A A cn Pa na 2 X 8 LL iii 8 T USB4 Top I I I I I P a VWs vane eam 20000000 LF 9 21 ee amp a 10 i iT H 12 LL 22Mb 3 PCIE1 14 2019 18 17 1615 1 CPU Fan Connector CPU_FAN1 12 SATA3 Connector SATA3_1 2 Chassis Fan Connector CHA_FAN1 13 32Mb SPI Flash 3 CPU Fan 14 Chassis Intrusion Header C11 4 CPU Heatsink 15 Chassis Speaker Header SPEAKER1 5 2 x 240 pin DDR3 DIMM Slots 16 Chassis Fan Connector CHA_FAN2 DDR3_A1 DDR3_A2 17 PCI Express 2 0 x16 Slot PCIE1 6 Clear CMOS Jumper CLRCMOS1 18 Consumer Infrared Module Header CIR1 7 ATX Power Connector ATXPWR1 19 USB 2 0 Header USB8_9 8 System Panel Header PANEL1 20 USB 2 0 Header USB6_7 9 SATA3 Connector SATA3_4 21 Front Panel Audio Header HD_AUDIO1 10 SATA3 Connector SATA3_2 22 COM Port Header COM1 11 SATA3 Connector SATA3_3 23 AMD A50M Chipset 12 1 5 1 0 Panel 1 PS 2 Keyboard
28. onent ensure that the power is 14 2 3 Installation of Memory Modules DIMM E35LM1 R2 0 motherboard provides two 240 pin DDR3 Double Data Rate 3 DIMM slots It is not allowed to install a DDR or DDR2 memory module into DDR3 slot otherwise this motherboard and DIMM may be damaged Installing a DIMM Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot lt lt notch lt break lt notch lt lt break The DIMM only fits in one correct orientation It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 15 2 4 Expansion Slot PCI Express Slot There is 1 PCI Express slot on this motherboard PCIE slot PCIE1 PCIE x16 slot is used for PCI Express x4 lane width graphics cards Installing an expansion card Step 1 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove
29. pdates from our servers In other words the system can auto detect the latest UEFI from our servers and flash them without entering Windows OS Please note that you must be running on a DHCP configured computer in order to enable this function ASRock UEFI System Browser ASRock UEFI system browser is a useful tool included in graphical UEFI It can detect the devices and configurations that users are currently using in their PC With the UEFI system browser you can easily examine the current system configura tion in UEFI setup ASRock Dehumidifier Function Users may prevent motherboard damages due to dampness by enabling Dehumidifier Function When enabling Dehumidifier Function the computer will power on automatically to dehumidi fy the system after entering S4 S5 state ASRock Fast Boot With ASRock s exclusive Fast Boot technology it takes less than 1 5 seconds to logon to Windows 8 from a cold boot No more waiting The speedy boot will completely change your user experience and behavior ASRock Restart to UEFI Windows 8 brings the ultimate boot up experience The light ning boot up speed makes it hard to access the UEFI setup AS Rock Restart to UEFI technology is designed for those requiring frequent UEFI access It allows users to easily enter the UEFI automatically when turning on the PC next time Just simply enable this function the PC will be assured to access the UEFI directly in the very beginning ASR
30. s Auto Write Recovery Time tWR Use this item to change Write Recovery Time tWR Auto Manual setting The default is Auto Refresh Cycle Time tRFC Use this item to change Refresh Cycle Time tRFC Auto Manual setting The default is Auto RAS to RAS Delay tRRD Use this item to change RAS to RAS Delay tRRD Auto Manual setting The default is Auto Write to Read Delay tWTR Use this item to change Write to Read Delay tWTR Auto Manual setting The default is Auto Read to Precharge tRTP Use this item to change Read to Precharge tRTP Auto Manual setting The default is Auto Four Activate Window tFAW Use this item to change Four Activate Window tFAW Auto Manual setting The default is Auto 32 Voltage Configuration DRAM Voltage Use this to select DRAM Voltage The default value is Auto FCH Voltage Use this to select FCH Voltage The default value is Auto 1 8V Voltage Use this to select 1 8V Voltage The default value is Auto 1V Voltage Use this to select 1V Voltage The default value is Auto 33 3 4 Advanced Screen In this section you may set the configurations for the following items CPU Configu ration North Bridge Configuration South Bridge Configuration Storage Configura tion Super IO Configuration ACPI Configuration and USB Configuration ASRock UEFI setup Utility a ms Tool Setting wrong values in this section may cause the system to malfunction
31. sable USB Keyboard Remote to turn on the system from the power soft off mode USB Mouse Power On Use this item to enable or disable USB Mouse to turn on the system from the power soft off mode 40 CSM Please disable CSM when you enable Fast Boot option The default value is Enabled 41 3 4 7 USB Configuration ASRock UEFI setup Utility r In USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller Legacy USB Support Use this option to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility is sue it is recommended to select Disabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS 42 3 5 Tool ASRock UEFI setup utility OC Tweaker System Browser System Browser can let you easily check your current system configura tion in UEFI setup OMG Online Management Guard Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG You may schedule the star
32. sh Just launch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other compli cated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system ASRock APP Charger If you desire a faster less restricted way of charging your Apple devices such as iPhone iPad iPod Touch ASRock has prepared a wonderful solution for you ASRock APP Charger Simply install the APP Charger driver it makes your iPhone charge much quickly from your computer and up to 40 faster than before ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continu ous charging when your PC enters into Standby mode S1 Suspend to RAM S3 hibernation mode S4 or power off S5 With APP Charger driver installed you can easily enjoy the mar velous charging experience ASRock XFast USB ASRock XFast USB can boost USB storage device perfor mance The performance may depend on the properties of the device ASRock XFast LAN ASRock XFast LAN provides a faster internet access which includes the benefits listed below LAN Application Prioritiza tion You can configure your application s priority ideally and or add new programs Lower Latency in Game After setting online game s priority higher it can lower the latency in games Traffic Shap
33. sis cover has been removed This feature requires a chassis with chassis intrusion detection design 23 2 8 Serial ATA3 SATA3 Hard Disks Installation This motherboard adopts AMD A50M chipset that supports Serial ATA3 SATA3 hard disks You may install SATA3 hard disks on this motherboard for internal stor age devices This section will guide you to install the SATA3 hard disks STEP 1 Install the SATA3 hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA3 hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATA3 connector STEP 4 Connect the other end of the SATA data cable to the SATA3 hard disk 2 9 Hot Plug Function for SATA3 HDDs This motherboard supports Hot Plug function for SATA3 in AHCI mode AMD A50M chipset provides hardware support for Advanced Host controller Interface AHCI a new programming interface for SATA host controllers developed thru a joint industry effort 4 NOTE What is Hot Plug Function If the SATA3 HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA3 HDDs while the system is Still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA3 HDD 24 2 10 SATA3 HDD Hot Plug Feature and Operation Guide This motherboard supports Hot Plug feature for SATA3 HDD in RAID AHCI mode Please
34. stalled devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard sup ports Click on a specific item then follow the installation wizard to install it 4 24 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 50 Installing OS on a HDD Larger Than 2TB This motherboard is adopting UEFI BIOS that allows Windows OS to be installed on a large size HDD gt 2TB Please follow below procedure to install the operating system 1 Please make sure to use Windows Vista 64 bit with SP1 or above Windows 7 64 bit or Windows 8 64 bit 2 Press lt F2 gt or lt Delete gt at system POST Set AHCI Mode in UEFI Setup Utility gt Advanced gt Storage Configuration gt SATA Mode 3 Choose the item UEFI xxx to boot in UEFI Setup Utility gt Boot gt Boot Option 1 5007 is the device which contains your Windows installation files Normally it is an optical drive You can also press lt F11 gt to launch boot menu at system POST and choose the item UEFI xxx to boot 4 Start Windows installation 5 If you install Windows 7 64 bit OS OS will be formatted by GPT GUID Partition Table Please install the hotfix file from Microsoft http support microsof
35. t CD Information smvenemieseemmenemm inek 50 4 2 1 Running Support CDs 50 422 Drivers WONG iesiaiuatsarasiarictanaxteterssactaaivinwiiatianimatads 50 4 2 3 Utilities Menu usuumananqmsuisuneaemestdniihei 50 4 2 4 Contact Information uaeueeme4sssnsneimmsiemssvsmien 50 Thank you for purchasing ASRock E35LM1 R2 0 motherboard a reliable mother board produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to Chapter 1 Introduction quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without no tice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest VGA cards and CPU support lists on ASRock website as well ASRock website _ http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock E35LM1 R2 0 Motherboard Mini ITX Form Factor ASRock E35LM1 R2 0 Quick I
36. t com kb 979903 51
37. the Operating System Security To set up the security features Exit To exit the current screen or the UEFI SETUP UTILITY Use lt lt gt key or lt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen You can also use the mouse to click your required item 29 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description lt Moves cursor left or right to select Screens io Moves cursor up or down to select items To change option for the selected items lt Tab gt Switch to next function lt Enter gt To bring up the selected screen lt PGUP gt Go to the previous page lt PGDN gt Go to the next page lt HOME gt Go to the top of the screen lt END gt Go to the bottom of the screen lt F1 gt To display the General Help Screen lt F7 gt Discard changes and exit the UEFI SETUP UTILITY lt F9 gt Load optimal default values for all the settings lt F10 gt Save changes and exit the UEFI SETUP UTILITY lt F12 gt Print screen lt ESC gt Jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview ASRock UEFI setup Utility 30 3 3 OC Tweaker Screen In the OC Tweaker screen you can set up overclocking features ASRock UEFI setup Utility 4
38. the system unit cover if your motherboard is already installed in a chassis Step 3 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 5 Fasten the card to the chassis with screws Step 6 Replace the system cover 16 2 5 ASRock Smart Remote Installation Guide ASRock Smart Remote is only used for ASRock motherboard with CIR header Please refer to below procedures for the quick installation and usage of ASRock Smart Remote Step Step2 Step3 Step4 Step5 Find the CIR header located next to the USB 2 0 header on ASRock B2 0h pi lack motherboard US 0 header 9 pin black CIR header 4 pin gray USB 2 0 header as below pin 1 5 and the CIR header Please make sure the wire assignments and the pin assignments are matched correctly ATX 5VSB Install Multi Angle CIR Receiver to the front USB port Boot up your system Press lt F2 gt or lt Del gt to enter BIOS Setup Utility Make sure the option CIR Controller is setting at Enabled Advanced gt Super IO Configuration gt CIR Controller gt Enabled If you cannot find this option please shut down your system and install Multi Angle CIR Receiver to the other front USB port then try again Enter Windows Execute ASRock support CD and install CIR Driver It is listed at
39. ting and ending hours of internet access granted to other users In order to prevent users from bypassing OMG guest accounts without permission to modify the system time are required UEFI Update Utility Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM This conve nient UEFI update tool allows you to update system UEFI without enter ing operating systems first like MS DOS or Windows Just save the new UEFI file to your USB flash drive floppy disk or hard drive and launch this tool then you can update your UEFI only in a few clicks without prepar ing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to up date your UEFI and reboot your system after the UEFI update process is completed Internet Flash Internet Flash searches for available UEFI firmware updates from our servers In other words the system can auto detect the latest UEFI from our servers and flash them without entering Windows OS Please note that you must be running on a DHCP configured computer in order to 43 enable this function Network Configuration ASRock UEFI setup Utility r In Internet Setting Use this item to set up the internet connection mode Configuration options DHCP Auto IP
Download Pdf Manuals
Related Search