Teac DV-516E (DV516D000E000DA00) Internal DVD Drive
Contents
1. detected automatically by Windows 98SE Me 2000 XP and assigned a logical drive letter There is no need to install any drivers Windows NT 4 0 Users Windows NT 4 0 does not support the Plug N Play feature Therefore confirm that the IDE CD ROM DRIVE ATAPI version 1 2 driver is installed If not open the Control Panel double click SCSI Adapt ers click the Drivers tab then click the Add button At the Select a SCSI Adapter Option window select IDE CD ROM DRIVE ATAPI Ver 1 2 Click Install and follow the instructions on screen The drive will then be rec ognized by the operating system TEAC DVD ROM Installation Guide 6 Installing PowerDVD Software Installing PowerDVD Software PowerDVD is software that enables you to play DVD discs To install the PowerDVD software insert the included CD ROM that contains the PowerDVD software into your computer s CD ROM drive or the TEAC DVD ROM drive If Auto run is enabled on your system the on screen InstallShield Wizard will launch automatically If not click the Windows Start button then select Run gt D setup exe where D is the drive letter of the drive in which you inserted the PowerDVD CD ROM The Windows InstallShield Wizard displays the following panel PowerDVD XP Setup Welcome to the InstallShield Wizard for PowerDVD PowerDVD s playback performance depends on the power of your system s hardware A system with Pentiu2. drive using 3x5mm mounting screws Warning Do not use mounting screws longer than 3x5mm to secure the DVD ROM drive or you may damage the unit 5c Connect the DVD ROM to the vacant middle connector on your CD ROM CD RW interface cable If your original cable does not have an available middle connector you will need to acquire and install a standard IDE cable with three connectors Proceed to Step 6 Connect one end of the included audio cable to the analog audio connector on the rear panel of the DVD ROM drive then connect the other end to your sound card Note There is no need to install this cable if an audio cable is already con nected from your CD ROM CD RW drive to the sound card Use the CD ROM CD RW drive to listen to audio CDs TEAC DVD ROM Installation Guide 5 8 9 Installing the DVD ROM Drive Connect the power cable to the power connector on the rear panel of the DVD ROM drive Insert the power cable plug in the correct orientation into the power connector The plug is shaped so that it can be easily inserted in only one orientation do not force the plug into the connector The 5v terminal is on the left as you face the rear panel the 12v terminal is on the right The two center terminals are ground terminals Re install your computer s cover faceplate or bay cover Start your system Notes Q The TEAC DVD ROM drive is a true Plug N Play device therefore it will be
3. F 100 000 POH Dimensions 5 83 W x 1 67 H x 7 80 D Weight 2 31 Ibs Power Supplies 5VDC 12VDC Analog Audio Headphone 0 6 0 5Vrms at 32Q Line Out 0 7 0 1Vrms at 10kQ Headphone Jack 3 5mm diameter stereo mini jack Installation Horizontal or vertical 5 Operating Temperature 5 C to 45 C 41 F to 113 F Storage Temperature 30 C to 60 C 22 F to 140 F Operating Humidity Storage Humidity 5 to 85 non condensing 5 to 90 non condensing Safety Standards UL CSA TUV CE FDA Technical Support TEAC America Inc USA Technical Support Telephone 323 727 4860 Fax 323 869 8751 Monday Friday 8 00 a m 5 00 pm PST http www teac com DSPD techsupport htm E mail dspdtsg teac com TEAC DVD ROM Installation Guide 8
4. L Slave Master IDE interface power connector configuration jumper connector connector D analog audio output connector Use the included audio cable to connect this connector to the audio input connector on a sound card Pin assignments from right to left are described below Pin Number Audio Signal Pin Number Audio Signal 1 Left signal 3 Ground 2 Ground 4 Right signal CSEL Slave Master configuration jumper The DVD ROM drive includes five pairs of jumper pins on the rear panel Three of these pairs enable you to set the drive to CSEL Slave or Master mode See TEAC 16X DVD ROM Drive Installation Guide this manual on page 3 interface connector Use an IDE interface 40 pin ribbon cable to connect the DVD ROM drive to an IDE interface connector in your computer See Installing the DVD ROM Drive on page 4 power connector Connect the power connector to the 5 VDC and 12VDC power sources The 5 VDC terminal is on the left as you face the rear panel the 12VDC terminal is on the right The two center terminals are ground terminals TEAC DVD ROM Installation Guide 2 Recommended System Requirements Recommended System Requirements IBM PC compatible computer Pentium II 350MHz or higher An available 5 25 inch drive bay 64MB of RAM minimum 20MB free hard disk space Windows 98SE Me 2000 XP or NT 4 Service Pack 5 Graphics accelerator with DirectDraw COooovoecvv Soun
5. TEAC Installation Guide DV 516E 16X DVD ROM Drive headphone jack volume eject button disc tray control emergency eject LED indicator mechanism opening The TEAC DVD ROM drive is designed for use in IBM PC or compatible computers It features a 5 25 inch standard chassis and a powered tray for convenient disc loading The TEAC DVD ROM drive can read or play DVD and CD discs in a variety of formats including DVD ROM DVD video DVD R DVD RW DVD RW CD ROM CD audio CD R CD RW Video CD and more DVD discs supported have a playback capacity of 4 7GB to 17GB headphone jack You can connect headphones or external speakers that use a 3 5 mm stereo mini plug to this jack to listen to audio from a DVD or CD being played in your TEAC DVD ROM drive For external speakers connect a stereo adapter to split the output into separate cables for the left and right channels Such adapters convert a male stereo mini jack to two female phono jacks emergency eject mechanism If the eject button fails first turn off the power to the computer and then insert a small thin rod such as a straightened paper clip into the emergency eject mechanism opening and press firmly to eject the disc Caution Do not use the emergency eject mechanism when the LED indicator is lit or flashing or you may seriously damage the disc or the DVD ROM drive volume control Use t
6. computer to ground yourself This will prevent damage to the computer or DVD ROM drive that may be caused by a discharge of static electricity 3 Remove your computer s cover faceplate or 5 25 inch bay cover as well as any mounting clips screws and retaining brackets Note If you a have a SCSI CD RW or CD ROM drive already installed in your system or b do not have any IDE CD ROM or CD RW drives installed in your system continue with Step 4 If you already have an IDE CD ROM or CD RW drive installed in your system skip step 4 and continue with Step 5 4 Ifyou a have a SCSI CD RW or CD ROM drive installed in your system or b do not have any IDE CD ROM or CD RW drives installed in your system do the following 4a Confirm that the jumper on the rear panel of the DVD ROM drive is configured to its default setting of Master see TEAC 16X DVD ROM Drive Installation Guide this manual on page 3 4b Slide the DVD ROM drive into an empty 5 25 drive bay Secure the drive using the included 3x5mm mounting screws Warning Do not use mounting screws longer than 3x5mm to secure the DVD ROM drive or you may damage the unit secure drive with 3x5mm screws 4c Locate the secondary IDE connector on your system s motherboard and connect one end of the IDE interface cable to it Note The TEAC DVD ROM kit does not include an IDE interface cable If you need one you can purchase it from your loca
7. d card Package Contents TEAC 16X DVD ROM drive Audio cable Mounting screws CD ROM disc containing Power DVD XP video player software TEAC 16X DVD ROM Drive Installation Guide this manual DOODO Configuring the DVD ROM Drive The DVD ROM drive features five pairs of jumper pins on the rear panel By placing the jumper on the appropriate pair of pins you can set the drive to Master Slave or CSEL mode jumper The Master Slave CSEL jumper configuration of your TEAC DVD ROM drive depends on whether you already have an IDE CD ROM or CD RW drive installed in your system The following section will guide you through most typical system configurations CSEL CSEL CSEL SLAVE SLAVE SLAVE f pMASTER i pMASTER MASTER oda od 000 o o 0 oo og oo oa oa ao o oooa L 5 jumper jumper jumper set to CSEL set to Slave set to Master default TEAC DVD ROM Installation Guide 3 Installing the DVD ROM Drive Installing the DVD ROM Drive This section explains how to install the TEAC DVD ROM drive into an IBM PC or compatible computer The drive may be installed in a horizontal or vertical orientation within 5 of horizontal or vertical position Follow the steps below and refer to your computer documentation for information specific to your computer system 1 Turn off the power to the computer system and any external devices con nected to it 2 Touch the exposed metal frame of the
8. he volume control to adjust audio volume Turning the control to the right increases the volume Lower the volume before you play a disc to protect your hearing and speakers LED indicator The DVD ROM drive features an LED indicator light on the front panel Various operations are indicated as per the following table Rear Panel Operation LED Indication At tray loading green LED flashes At tray eject green LED flashes During audio play green LED flashes During seek data transfer green LED lights up steady At system drive start up green LED flashes Self diagnosis error green LED flashes eject button Press this button to open or close the disc tray Some DVD and CD ROM titles disable the manual eject button and rely on software commands to eject the disc Refer to the documentation for these titles for more information disc tray Use the disc tray to load discs into the drive Open the tray by pressing the eject button Close the tray by pressing the eject button Note Do not push the tray to close it Instead always press the eject button to eject or retract the tray Rear Panel CABLE SELECT SLAVE ANALOG AUDIO MASTER IDE INTERFACE DC INPUT CSM 39 1 RGGL slal l4 3 5V G G12V a baean sss 00 Ob boo oe ooo onana a aeea e O000 4 cI Lg analog audio CSE
9. l computer store TEAC DVD ROM Installation Guide 4 IDE interface ribbon cable 5 Installing the DVD ROM Drive Be certain to connect Pin 1 of the interface cable to Pin 1 on the secondary IDE connector on the motherboard Pin 1 on an interface cable is usually designated by a color strip along one edge of the cable Also the interface ribbon cable connector may feature a tab on one side Insert the cable so that the tab aligns with the notch on the drive s IDE interface connector Do not use excessive force while trying to insert the cable into position 4d Connect the other end of the IDE interface ribbon cable to the interface connector on the rear panel of the DVD ROM drive Skip Step 5 and proceed to Step 6 power cable If you already have an IDE CD ROM or CD RW drive installed in your system do the following Typically an IDE CD ROM or CD RW drive that is already installed in your system is connected to the secondary IDE motherboard connector and is configured as a Master In such cases it is strongly recommended that you configure the TEAC 16X DVD ROM drive as a Slave drive then connect it to the same cable that currently hosts your installed CD ROM or CD RW drive 5a Set the jumper on the rear panel of the TEAC DVD ROM drive to Slave see TEAC 16X DVD ROM Drive Installation Guide this manual on page 3 5b Slide the DVD ROM drive into the empty 5 25 inch drive bay Secure the
10. m Il 350 or above or any AMD Athlon CPU is highly recommended Click the Next button then follow the on screen InstallShield Wizard s instructions to complete the installation Note Once the software installation is completed you will be prompted to execute the system diagnostic program Select OK and make sure to enable DMA for the TEAC DV 516E and any other drive that supports this function The PowerDVD software features a graphic user interface that enables you to control the playback of DVD discs on the TEAC DVD ROM drive see figure below Click the Help button in the lower right corner of the CyberLink panel to display additional operational information Help button TEAC DVD ROM Installation Guide 7 Specifications Specifications Model DV 516E Interface IDE ATAPI Transfer Rate 16 6MB sec Data Transfer Rate DVD 8 91MBps 6 6X to 21 6MBps 16X CAV CD 3 09MBps 20 6X to 7 2MBps 48X CAV Access Time DVD 85 msec 1 3 Stroke CD 85 msec 1 3 Stroke Audio Extraction 40X maximum Buffer Size 512KB Disc Formats Sup ported DVD Single and Dual Layer DVD R DVD RW DVD RW XA Mode 2 Form1 Form2 Super Video CD CD Extra CD Plus UDF CD I Photo CD Single and Multisession CD R CD RW MultiRead Disc Size 12cm and 8cm Front Panel Built in headphone jack LED indicator volume control knob and power eject button MTB
Download Pdf Manuals
Related Search