Enterasys (SWPIM-SY) Expansion Module
Contents
1. 7 NO LIABILITY FOR CONSEQUENTIAL DAMAGES IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU vi SWPIM SY Installation Guide Notice CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT IMPORTANT THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS EUROPE MIDDLE EAST AFRICA ASIA AUSTRALIA PACIFIC RIM BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an agreement Agreement between You the end user and Cabletron Systems Limited Cabletron that sets forth your rights and obligations with respect to the Cabletron software program Program in the package The Program may be contained in firmware chips or other media UTILIZING THE ENCLOSED PRODUCT YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT WHICH INCLUD2. LL Local Loopback DCEDTE DCE High or DTE Low RL Remote Loopback TM Test Mode A 2 SWPIM SY Installation Guide Environmental Requirements A 3 ENVIRONMENTAL REQUIREMENTS Operating Temperature 5 to 40 C 41 to 104 F Non operating Temperature 30 to 90 C 22 to 194 F Operating Humidity 5 to 90 Non condensing A 4 REGULATORY COMPLIANCE Safety UL 1950 without D3 deviations CSA C22 2 No 950 and EN 60950 EMI FCC Part 15 Class A EN 55022 Class A and VCCI Class I Electromagnetic EN 50082 1 including IEC 801 2 ESD IEC Compatibility EMC 801 3 Radiated Susceptibility and IEC patibility EMC 014 EFT B NEBS TR NWT 000063 Network Eguipment Building System NEBS Generic Eguipment Reguirements GR 1089 CORE EMC and Electrical Safety Generic Criteria for Network Telecommunications Eguipment Telecom CTR 2 Compliant listed under TUV Rheinland SWPIM SY Installation Guide A 3 Appendix A Specifications A 4 SWPIM SY Installation Guide APPENDIX B CABLES AND PINOUTS This appendix provides Cabletron Systems part numbers and connector pinouts for the following interface cables e EIA 449 e CCITT V 35 e EIA 232 e CCITT X21 e EIA 530 e ETA 530A B 1 INTERFACE CABLE PART NUMBERS Table B 1 lists the DTE interface cable part numbers and table numbers for the SWPIM SY The standard length for all cables is 10 feet Table B 1 DTE Interface Cable Types
3. Manufacturer Mr Ronald Fotino Full Name Compliance Engineering Manager Title Rochester NH USA Location SWPIM SY Installation Guide Legal Representative in Europe Mr J Solari Full Name Managing Director E M E A Title Newbury Berkshire England Location ix Notice X SWPIM SY Installation Guide CONTENTS INTRODUCTION Using TAS GUiGG tT xiii Structure of This xiii SWPIM SY ummistaa m r ss het ri FEE oc E Ebr C ETE xiv Related Manuals irene XV Document CONVENTIONS xvi Getting aloe LI xvii CHAPTER 1 INSTALLATION Unpacking the SWPIMSSY carrara drenato 1 1 installing the SWEPIMSSY icis secet itii ihre tee 1 2 EANVIEW LEED IGdICatiOllS ox io sais San ir 1 4 Connecting to tlie NetWork 1 4 Gompleting the Installationi a uaar 1 5 APPENDIX A SPECIFICATIONS PliysicaliPrOpertl6S A 1 Network III Tae susc cia tartine A 1 Environmental Requirements A 3 HegulatoryComplialiGe 5 355 0 58 5 cd DE E sse ta RO ORDEN Saba ues A 3 APPENDIX B CABLES AND PINOUTS Interface Cable Part B 1 RS449 DTE Gable B 2 5 on o B 4 RS2392
4. DCE Cable Table B 12 CCITT X 21 DCE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 15 Pin Female Conn w Back CCITT X 21 DCE pM CCITT X 21 DTE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Transmit Data 10 2 TXD A Transmit Data T DCE TXD B Transmit Data 28 N 9 TXD B Transmit Data T DTE RXD A Receive Data 5 4 RXD A Receive Data R DTE RXD B Receive Data 23 11 RXD B Receive Data R DTE CTS A Clear to Send 8 5 CTS A Clear to Send DTE CTS B Clear to Send 26 12 CTS B Clear to Send DCE RTS A Req to Send 9 3 RTS A Req to Send DCE RTS B Req to Send 27 i 10 RTS B Req to Send DTE RXC A Receive Timing 15 6 RXC A Receive Timing S DTE RXC B receive Timing 33 13 RXC B receive Timing S DTE CID2 Cable ID 20 21 Signal Common 16 8 Signal Common G Shield DRAIN 1 Note For Cable ID attach CID2 pin 20 to pin 21 SWPIM SY Installation Guide B 17 Appendix B Cables and Pinouts B 12 530 DCE CABLE Cable Part Number 9380416 Table B 13 EIA 530 DCE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 25 Pin Female Conn w Back EIA 530 DCE E Shell EIA 530 DTE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Trans Data 10 2 TXD A Trans Data BA D
5. relied upon by the exporting party If the Program is exported from the United States pursuant to the License Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes SWPIM SY Installation Guide Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the technology if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant o r any major component of a plant export to Country
6. w Back Shell A DB 25 Pin Male Conn w Back EIA 530A DTE PESI EIA 530A DCE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Trans Data 5 2 TXD A Trans Data BA DCE TXD B Trans Data 23 i 14 TXD B Trans Data BA DTE RXD A Rec Data 10 3 RXD A Rec Data BB DTE RXD B Rec Data 28 i 16 RXD B Rec Data BB DTE CTS A Clear to send 9 5 CTS A Clear to send CB DTE CTS B Clear to send 27 j 13 CTS B Clear to send CB DCE RTS A Req to Send 8 D 4 RTS A Req to Send CA DCE RTS B Req to Send 26 D 19 RTS B Req to Send CA DTE DCD A Carrier Detect 6 8 DCD A Carrier Detect CF DTE DCD B Carrier Detect 24 10 DCD B Carrier Detect CF DTE TXC A Trans Timing 17 15 TXC A Trans Timing DB DTE TXC B Trans Timing 35 i 12 TXC B Trans Timing DB DTE RXC A Rec Timing 13 17 RXC A Rec Timing DD DTE RXC B Rec Timing 31 E 9 RXC B Rec Timing DD DCE SCTE A Trans Timing 15 24 SCTE A Trans Timing DA DCE SCTE B Trans Timing 33 11 SCTE B Trans Timing DA DTE RI Ring Indicator 11 22 RI Ring Indicator RI DCE RL Remote loopback 36 21 RL Remote loopback RL DCE LL Local Loopback 18 18 LL Local Loopback LL DTE TM Test Mode 29 25 TM Test Mode TM B 10 SWPIM SY Installation Guide EIA 530A DTE Cable Table B 8 EIA 530A DTE Continued Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 25 Pin Male Conn w Back I Shell EIA 530A DTE R EIA 530A DCE D
7. 7 DTE CABLE irte incertos B 6 GGITT X21 DTE Cable iiec ia B 7 EIA 530 DTE Cable B 8 EIA 530A d 10 RSA449 DGE Cable iicet in iet ades tete B 12 GOITT V 35 PEE iiec n B 14 RS232 DCE Gable i B 16 GGITT3 21 7 DCE Cable i io tete titi t cesis B 17 EIA b39 DOE Cable B 18 EIA 530A DCE Cable iii B 20 SWPIM SY Installation Guide xi Contents Xii SWPIM SY Installation Guide INTRODUCTION Only qualified personnel should perform installation procedures Welcome to the Cabletron Systems SWPIM SY Installation Guide This manual provides an introduction to the SWPIM SY lists features and capabilities details the cabling pinouts and explains how to install the SWPIM SY The SWPIM SY Sliding WAN Physical Interface Module provides six different synchronous asynchronous serial interface protocol connections to external communications equipment e g a multiplexer or CSU DSU for a host platform designed to receive the SWPIM architecture The term host platform may be used to indicate the device or NOTE interface module such as the SSR 600 or the HSIM SSR 600 into which the SWPIM SY is installed USING THIS GUIDE Read through this guide completely to understand the features and capabilities of the SWPIM SY A
8. BECOME BOUND BY THE TERMS OF THIS AGREEMENT WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT RETURN THE UNOPENED PRODUCT TO CABLETRON OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT CABLETRON SYSTEMS 1 603 332 9400 Attn Legal Department 1 LICENSE You have the right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this License Agreement You may not copy reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron 2 OTHER RESTRICTIONS You may not reverse engineer decompile or disassemble the Program 3 APPLICABLE LAW This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire You accept the personal jurisdiction and venue of the New Hampshire courts 4 EXPORT REQUIREMENTS You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the product is obtained from the U S Government or an exception from obtaining such license may be
9. Back Shell M Series 34 Pin Female Conn CCITT V 35 DCE W BaCk CCITT V 35 DTE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Transmit Data 10 P TXD A Transmit Data 103 DCE TXD B Transmit Data 28 S TXD B Transmit Data 103 DTE RXD A Receive Data 5 R RXD A Receive Data 104 DTE RXD B Receive Data 23 T RXD B Receive Data 104 DTE CTS Clear to Send 8 D CTS Clear to Send 106 DCE RTS Req to Send 9 RTS Req to Send 105 DTE DCD Carrier Detect 6 F DCD Carrier Detect DTE TXC A Transmit Timing 17 Y TXC A Transmit Timing 114 DTE TXC B Transmit Timing 35 AA TXC B Transmit Timing 114 DTE RXC A Receive Timing 15 V RXC A Receive Timing 115 DTE RXC B Receive Timing 33 X RXC B Receive Timing 115 DCE SCTE A Transmit Timing 13 U SCTE A Transmit Timing 113 DCE SCTE B Transmit Timing 31 W SCTE B Transmit Timing 113 DTE RI Ring Indicator 18 J RI Ring Indicator 125 DCE RL Remote Loopback 29 N RL Remote Loopback 140 DCE LL Local Loopback 11 L LL Local Loopback 141 DTE TM Test Mode 36 NN TM Test Mode 142 DTE DSR DCE Set Ready 14 E DSR Data Set Ready 107 DCE DTR DTE Term Ready 4 H DTR Data Term Ready 108 DTE CIDO Cable ID 19 21 B 14 SWPIM SY Installation Guide Table B 10 CCITT V 35 DCE Cable Continued CCITT V 35 DCE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A M Series 34 Pin Female Conn CCITT V 35 DCE WiBack shell CCITT V 35 DTE
10. Dir Signal Name Pin Pin Signal Name Mne To monic DTE CID1 Cable ID 2 21 Signal Ground 25 A Signal Ground Signal common 16 B Signal Common 102 Shield DRAIN 1 Note For Cable ID attach CIDO pin 19 to pin 21 For Cable ID attach CID1 pin 2 to pin 21 SWPIM SY Installation Guide B 15 Appendix B Cables and Pinouts B 10 RS232 DCE CABLE Cable Part Number 9380415 Table B 11 RS232 DCE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back A DB 25 Pin Female Conn w Back Shell Shell RS232 DCE RS232 DTE Dir Signal Name Signal Name Mne To monic DCE TXD Transmit Data TXD Transmit Data DTE RXD Receive Data RXD Receive Data DTE CTS Clear to Send CTS Clear to Send DCE RTS Req to Send RTS Req to Send DTE DCD Carrier Detect DCD Carrier Detect DTE TXC Transmit Timing TXC Transmit Timing DTE RXC Receive Timing RXC Receive Timing DCE SCTE Transmit Timing SCTE Transmit Timing DTE RI Ring Indicator RI Ring Indicator DCE RL Remote Loopback RL Remote Loopback DCE LL Local Loopback LL Local Loopback DTE TM Test Mode TM Test Mode DTE DSR DCE Ready DSR DCE Ready DCE DTR DTE Ready DTR DTE Ready DTE CIDO Cable ID 19 21 Signal Common 16 7 Signal Common AB Shield DRAIN 1 Note For Cable ID attach CIDO pin 19 to pin 2 B 16 SWPIM SY Installation Guide B 11 CCITT X 21 DCE CABLE Cable Part Number 9380417 CCITT X 21
11. Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Product i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Cabletron and or its suppliers For Department of Defense units the Product is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 EXCLUSION OF WARRANTY Except as may be specifically provided by Cabletron in writing Cabletron makes no warranty expressed or implied concerning the Program including its documentation and media CABLETRON DISCLAIMS ALL WARRANTIES OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PROGRAM THE ACCOMPANYING WRITTEN MATERIALS AND ANY ACCOMPANYING HARDWARE
12. and Cabletron Part Numbers Interface Type Maximum Cabletron Part Table Number Length feet Number RS449 500 9380414 Table B 3 CCITT V 35 200 9380413 Table B 4 RS232 50 9380412 Table B 5 CCITT X 21 500 9380410 Table B 6 EIA 530 500 9380411 Table B 7 EIA 530A 500 9380420 Table B 8 SWPIM SY Installation Guide Appendix B Cables and Pinouts Table B 2 lists the DCE interface cable part numbers and table numbers for the SWPIM SY The standard length for all cables is 10 feet Table 2 DCE Interface Cable Types and Cabletron Part Numbers Interface Type Maximum Cabletron Part Table Number Length feet Number RS449 500 9380419 Table B 9 CCITT V 35 200 9380418 Table B 10 RS232 50 9380415 Table B 11 CCITT X 21 500 9380417 Table B 12 EIA 530 500 9380416 Table B 13 EIA 530A 500 9380421 Table B 14 For all the following tables Dir To indicates the direction of the signal Notes at the bottom of all the tables in this Appendix are supplied as reference information for cable construction They can be ignored if the cable has been supplied by the vendor B 2 Cable Part Number Connector 1 36 Pin Male Conn w Back Shell 9380414 RS449 DTE CABLE Table B 3 RS449 DTE Cable A Connector 2 DB 37 Pin Male Conn w Back Shell RS449 DTE R RS449 DCE Dir Signal Name Pin Pin Signal Name Mne To monic Sign
13. and pin assignments for these cables The interface network cable types are software detectable The SWPIM SY detects the type of cable attached and whether it is DTE or DCE The SWPIM SY is capable of receiving or transmitting clock in either DTE or DCE mode Refer to the host platform software user s manual for information on how to configure the SWPIM SY using software The SWPIM SY has an LED to indicate link traffic and standby conditions Refer to Chapter 1 for more details For supported WAN protocols refer to the host platform software user s manual xiv SWPIM SY Installation Guide Introduction RELATED MANUALS The following Cabletron Systems manuals may help the user to set up and manage the SWPIM SY SSR 600 Installation Guide HSIM SSR 600 Installation Guide 6C105 SmartSwitch 6000 Overview and Setup Guide Ethernet Technology Guide Cabling Guide The manuals referenced above can be obtained on the World Wide Web in Adobe Acrobat Portable Document Format PDF at the following site http www cabletron com Cabletron Systems applicable software manuals for the SSR 600 and the HSIM SSR 600 host platforms Cabletron Routing Software Manuals Bridging Configuration Guide Event Logging System Message Guide Network Interface Operations Guide Routing Protocols Reference Guide Routing Protocols User s Guide System Software Guide ClearVISN Routing Configurator User s Guide Systems Network Architecture
14. B Transmit Timing 35 N 23 TXC B Send Timing ST DCE LL Local Loopback 18 10 LL Local Loopback LL DTE TM Test Mode 29 18 TM Test Mode TM DCE RL Remote Loopback 36 14 RL Remote Loopback RL DTE DCEDTE_ 3 7 DTE CID1 Cable ID 2 21 Signal Common 16 a Sana aroung Signal SG SC Shield DRAIN 1 Note For DTE attach DCEDTE_ pin 3 to pin 7 For Cable ID attach CID1 pin 2 to pin 21 SWPIM SY Installation Guide B 3 Appendix B Cables and Pinouts CCITT V 35 DTE CABLE Cable Part Number 9380413 Table B 4 CCITT V 35 DTE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back A M Series 34 Pin Male Conn Shell w Back Shell CCITT V 35 DTE CCITT V 35 DCE Dir Signal Name Pin Pin 2 Signal Name Mne To monic DCE TXD A Transmit Data 5 P TXD A Transmit Data 103 DCE TXD B Transmit Data 23 5 TXD B Transmit Data 103 DTE RXD A Receive Data 10 R RXD A Receive Data 104 DTE RXD B Receive Data 28 i T RXD B Receive Data 104 DTE CTSClearto Send 9 D CTS Clear to Send 106 DCE RTS Req to Send 8 RTS Req to Send 105 DTE DCD Carrier Detect 6 F DCD Carrier Detect DTE TXC A Transmit Timing 17 Y TXC A Transmit Timing 114 DTE TXC B Transmit Timing 35 AA TXC B Transmit Timing 114 DTE RXC A Receive Timing 18 V RXC A Receive Timing 115 DTE RXC B Receive Timing 31 X RXC B Receive Timing 115 DCE SCTE A Transmit Timing 15 U SCTE A Transmit Timing 113 DCE
15. BLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU viii SWPIM SY Installation Guide Notice DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Conformance to Directive s Product Standards Equipment Type Environment 89 336 EEC 73 23 EEC Cabletron Systems Inc 35 Industrial Way PO Box 5005 Rochester NH 03867 Mr J Solari Cabletron Systems Limited Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England EC Directive 89 336 EEC EC Directive 73 23 EEC EN 55022 EN 50082 1 EN 60950 Networking Equipment for use in a Commercial or Light Industrial Environment We the undersigned hereby declare under our sole responsibility that the equipment packaged with this notice conforms to the above directives
16. CE TXD B Trans Data 28 14 TXD B Trans Data BA DTE RXD A Rec Data 5 3 RXD A Rec Data BB DTE RXD B Rec Data 23 i 16 RXD B Rec Data BB DTE CTS A Clear to send 8 5 CTS A Clear to send CB DTE CTS B Clear to send 26 13 CTS B Clear to send CB DCE RTS A Reg toSend 9 D 4 RTS A Reg to Send CA DCE RTS B Reg to Send 27 D 19 RTS B Reg to Send CA DTE DCD A Carrier Detect 6 8 DCD A Carrier Detect CF DTE DCD B Carrier Detect 24 10 DCD B Carrier Detect CF DTE TXC A Trans Timing 17 15 TXC A Trans Timing DB DTE TXC B Trans Timing 35 12 TXC B Trans Timing DB DTE RXC A Rec Timing 15 17 RXC A Rec Timing DD DTE RXC B Rec Timing 33 e 9 RXC B Rec Timing DD DCE SCTE A Trans Timing 13 24 SCTE A Trans Timing DA DCE SCTE B Trans Timing 31 i 11 SCTE B Trans Timing DA DCE RL Remote loopback 29 21 RL Remote loopback RL DCE LL Local Loopback 11 18 LL Local Loopback LL DTE TM Test Mode 36 25 TM Test Mode TM DTE DSR A DCE Set Ready 14 6 DSR A DCE Set Ready cc DTE DSR B DCE Set Ready 32 22 DSR B DCE Set Ready cc B 18 SWPIM SY Installation Guide EIA 530 DCE Cable Table B 13 EIA 530 DCE Cable Continued Connector 1 Connector 2 36 Pin Male Conn w Back Shell A DB 25 Pin Female Conn w Back EIA 530 DCE 4 nel EIA 530 DTE Dir Signal Name Pin Pin Signal Name Mne To monic DCE DTR ADTE Term Ready 4 20 DTR A DTE Term Ready CD DCE DTR B DTE Term Read
17. ES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT RETURN THE UNOPENED PRODUCT TO CABLETRON OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT CABLETRON SYSTEMS 1 603 332 9400 Attn Legal Department 1 LICENSE You have the right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this License Agreement You may not copy reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron 2 OTHER RESTRICTIONS You may not reverse engineer decompile or disassemble the Program 3 APPLICABLE LAW This License Agreement shall be governed in accordance with English law The English courts shall have exclusive jurisdiction in the event of any disputes 4 EXPORT REQUIREMENTS You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the product is obtained from the U S Government or an exception from obtaining such license may be relied upon by the exporting party If the Program is exported from the United States pursuant to
18. G THE ENCLOSED PRODUCT YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT RETURN THE UNOPENED PRODUCT TO CABLETRON OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT CABLETRON SYSTEMS 1 603 332 9400 Attn Legal Department 1 LICENSE You have the right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this License Agreement You may not copy reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron 2 OTHER RESTRICTIONS You may not reverse engineer decompile or disassemble the Program 3 APPLICABLE LAW This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire You accept the personal jurisdiction and venue of the New Hampshire courts 4 EXPORT REQUIREMENTS You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the product is obtained from the U S Government or an
19. Guide Quick Reference Guide DTF Data Trace Facility User Guide SWPIM SY Installation Guide XV Introduction DOCUMENT CONVENTIONS The following conventions may be used in this document Note symbol Calls the reader s attention to any item of information that may be of special importance Tip symbol Conveys helpful hints concerning procedures or actions Caution symbol Contains information essential to avoid damage to the equipment Electrical Hazard Warning symbol Warns against an action that could result in personal injury or death due to an electrical hazard gt gt xvi SWPIM SY Installation Guide Introduction GETTING HELP For additional support related to this device or document contact Cabletron Systems using one of the following methods World Wide Web http www cabletron com Phone 603 332 9400 Internet mail support cabletron com FTP ftp ftp cabletron com Login anonymous Password your email address To send comments or suggestions concerning this document contact the Cabletron Systems Technical Writing Department via the following email address TechWriting cabletron com Make sure to include the document Part Number in the email message Before calling Cabletron Systems have the following information ready Your Cabletron Systems service contract number A description of the failure A description of any action s already taken to resolve the probl
20. OTICE The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence Numbers of all the devices does not exceed 5 VCCI NOTICE This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions CORRI V CC I OLE TORE RIERE CHATS CHE EEITILK DET ZLIBRSNSTEMBOET SWPIM SY Installation Guide Notice CABLETRON SYSTEMS INC PROGRAM LICENSE AGREEMENT IMPORTANT THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS CANADA MEXICO CENTRAL AMERICA SOUTH AMERICA BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an agreement Agreement between You the end user and Cabletron Systems Inc Cabletron that sets forth your rights and obligations with respect to the Cabletron software program Program in the package The Program may be contained in firmware chips or other media UTILIZIN
21. RXC B Rec Timing DD DCE SCTE A Trans Timing 13 H 24 SCTE A Trans Timing DA DCE SCTE B Trans Timing 31 11 SCTE B Trans Timing DA DTE RI Ring Indicator 18 22 RI Ring Indicator RI DCE RL Remote loopback 29 21 RL Remote loopback RL B 20 SWPIM SY Installation Guide EIA 530A DCE Cable Table B 14 530A DCE Cable Continued Connector 1 Connector 2 36 Pin Male Conn w Back DB 25 Pin Female Conn w Back Shell Shell EIA 530A DCE R EIA 530A DTE Signal Name Pin Pin Signal Name Mne monic LL Local Loopback 11 18 LL Local Loopback LL TM Test Mode 36 25 TM Test Mode TM DSR DCE Set Ready 14 l 6 DSR DCE Set Ready cc DTR DTE Term Ready 4 J 20 DTR DTE Term Ready CD CID2 Cable ID 20 21 CID1 Cable ID 2 21 Signal Ground 25 1 Signal Ground Signal Common 16 7 Signal Common AB Signal Common 34 23 Signal Common AC Signal DRAIN 1 7 Note For Cable ID attach CID2 pin 20 to pin 21 For Cable ID attach CID1 SWPIM SY Installation Guide pin 2 to pin 21 B 21 Appendix B Cables and Pinouts B 22 SWPIM SY Installation Guide
22. Receive Data 5 6 RXD A Receive Data RD DTE RXD B Receive Data 23 i 24 RXD B Receive Data RD DTE RI Ring Indicator 18 15 RI Incoming Call IC DTE RXC A Receive Timing 15 8 RXC A Receive Timing RT DTE RXC B Receive Timing 38 i 26 RXC B Receive Timing RT DCE DTR A Terminal Ready 4 12 DTR A Terminal Ready TR DCE DTR B Terminal Ready 22 i 30 DTR B Terminal Ready TR DCE SCTE A Transmit Timing 13 17 SCTE A Terminal Timing TT DCE SCTE B Transmit Timing 31 35 SCTE B Terminal Timing TT B 12 SWPIM SY Installation Guide RS449 DCE Cable Table B 9 RS449 DCE Cable Continued Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 37 Pin Female Conn w Back RS449 DCE Shell RS449 DTE To monic DTE TXC A Transmit Timing 17 5 TXC A Send Timing ST DTE TXC B Transmit Timing 35 N 23 TXC B Send Timing ST DCE LL Local Loopback 11 10 LL Local Loopback LL DTE TM Test Mode 36 18 TM Test Mode TM DCE RL Remote Loopback 29 14 RL Remote Loopback RL DTE CID1 Cable ID 2 21 Signal Common 16 k Signal Arouna Signal E Shield DRAIN 1 Note For Cable ID attach CID1 pin 2 to pin 21 SWPIM SY Installation Guide B 13 Appendix B Cables and Pinouts B 9 CCITT V 35 DCE CABLE Cable Part Number 9380418 Table B 10 CCITT V 35 DCE Cable Connector 1 Connector 2 36 Pin Male Conn w
23. SCTE B Transmit Timing 33 W SCTE B Transmit Timing 113 DTE RI Ring Indicator 11 J RI Ring Indicator 125 DCE RL Remote Loopback 36 N RL Remote Loopback 140 DCE LL Local Loopback 18 L LL Local Loopback 141 DTE TM Test Mode 29 NN TM Test Mode 142 DTE DSR DCE Set Ready 4 E DSR Data Set Ready 107 DCE DTR DTE Term Ready 14 H DTR Data Term Ready 108 SWPIM SY Installation Guide Table B 4 CCITT V 35 DTE Cable Continued CCITT V 35 DTE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back A M Series 34 Pin Male Conn Shell w Back Shell R CCITT V 35 DTE CCITT V 35 DCE Dir Signal Name Pin Pin Signal Name Mne To monic DTE CIDO Cable ID 19 21 DTE CID1 Cable ID 2 21 DTE DCEDTE 3 7 Signal Ground 25 A Signal Ground Signal common 16 B Signal Common 102 Shield DRAIN 1 Note For attach DCEDTE 3 to pin 7 For Cable ID attach CIDO pin 19 to pin 21 For Cable ID attach CID1 pin 2 to pin 21 SWPIM SY Installation Guide B 5 Appendix B Cables and Pinouts B 4 RS232 DTE CABLE Cable Part Number 9380412 Table B 5 RS232 DTE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 25 Pin Male Conn w Back RS232 DTE A Snell RS232 DCE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD Transmit Data 5 2 TXD Transmit Dat
24. SWPIM SY Installation Guide CABLETRON Systems 9033001 02 Only qualified personnel should perform installation procedures NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made The hardware firmware or software described in this manual is subject to change without notice IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF KNOWN OR SHOULD HAVE KNOWN THE POSSIBILITY OF SUCH DAMAGES Cabletron Systems Inc 35 Industrial Way Rochester NH 03867 1999 by Cabletron Systems Inc AII Rights Reserved Printed in the United States of America Order Number 9033001 02 October 1999 Cabletron Systems SPECTRUM and LANVIEW are registered trademarks and SmartSwitch is a trademark of Cabletron Systems Inc All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies FCC NOTICE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful
25. Timing DD DTE RXC B Rec Timing 31 9 RXC B Rec Timing DD DCE SCTE A Trans Timing 15 24 SCTE A Trans Timing DA DCE SCTE B Trans Timing 33 11 SCTE B Trans Timing DA DCE RL Remote loopback 36 21 RL Remote loopback RL DCE LL Local Loopback 18 18 LL Local Loopback LL DTE TM Test Mode 29 25 TM Test Mode TM B 8 SWPIM SY Installation Guide EIA 530 DTE Cable Table B 7 530 DTE Cable Continued Connector 1 Connector 2 36 Pin Male Conn w Back Shell DB 25 Pin Male Conn w Back Shell EIA 530 DTE EIA 530 DCE Dir Signal Name Pin Pin Signal Name Mne To monic DTE DSR A DCE Set Ready 4 6 DSR A DCE Set Ready CC DTE DSR B DCE Set Ready 22 22 DSR B DCE Set Ready CC DCE DTR ADTE Term Ready 14 20 DTR A DTE Term Ready CD DCE DTR BDTE Term Ready 32 23 DTR B DTE Term Ready CD DTE CID1 Cable ID 2 21 DTE CID3 Cable ID 30 21 DTE DCEDTE_ 3 7 Signal Ground 25 1 Signal Ground Signal Common 16 7 Signal Common AB Signal DRAIN 1 7 Note For DTE attach DCEDTE_ pin 3 to pin 7 For Cable ID attach CID1 pin 42 to pin 21 For Cable ID attach CID3 pin 30 to pin 21 SWPIM SY Installation Guide B 9 Appendix B Cables and Pinouts B 7 EIA 530A DTE CABLE Cable Part Number 9380420 Table B 8 530 DTE Connector 1 P Connector 2 36 Pin Male Conn
26. WRITTEN MATERIALS AND ANY ACCOMPANYING HARDWARE 7 NO LIABILITY FOR CONSEQUENTIAL DAMAGES IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU iv SWPIM SY Installation Guide Notice CABLETRON SYSTEMS SALES AND SERVICE INC PROGRAM LICENSE AGREEMENT IMPORTANT THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA AND BY UNITED STATES OF AMERICA GOVERNMENT END USERS BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an agreement Agreement between You the end user and Cabletron Systems Sales and Service Inc Cabletron that sets forth your rights and obligations with respect to the Cabletron software program Program in the package The Program may be contained in firmware chips or other media UTILIZING THE ENCLOSED PRODUCT YOU ARE AGREEING TO
27. a BA DTE RXD Receive Data 10 3 RXD Receive Data BB DTE CTS Clear to Send 9 5 CTS Clear to Send CB DCE RTS Req to Send 8 4 RTS Req to Send CA DTE DCD Carrier Detect 6 8 DCD Carrier Detect DTE TXC Transmit Timing 17 15 TXC Transmit Timing DB DTE RXC Receive Timing 13 17 RXC Receive Timing DD DCE SCTE Transmit Timing 15 24 SCTE Transmit Timing DA DTE RI Ring Indicator 11 22 RI Ring Indicator CE DCE RL Remote Loopback 36 21 RL Remote Loopback RL DCE LL Local Loopback 18 18 LL Local Loopback LL DTE TM Test Mode 29 25 TM Test Mode TM DTE DSR DCE Ready 4 6 DSR DCE Ready cc DCE DTR DTE Ready 14 20 DTR DTE Ready CD DTE CIDO Cable ID 19 21 DTE DCEDTE 9 7 Signal Common 16 7 Signal Common AB Shield DRAIN 1 Note For DTE attach DCEDTE pin 3 to pin 7 For Cable ID attach CIDO pin 19 to pin 21 B 6 SWPIM SY Installation Guide CCITT X 21 DTE Cable B 5 CCITT X 21 DTE CABLE Cable Part Number 9380410 Table B 6 CCITT X 21 DTE Cable Connector 1 Connector 2 36 Pin Male Conn w Back DB 15 Pin Male Conn w Back Shell Shell CCITT X 21 DTE CCITT X 21 DCE Signal Name TXD A Transmit Data Signal Name TXD A Transmit Data Mne monic TXD B Transmit Data TXD B Transmit Data RXD A Receive Data RXD A Receive Data RXD B Receive Data RXD B Receive Data CTS A Clear to Send CTS B Clear to Send CTS A Clear to Send CTS B Clear to Send RTS A Re
28. al Common 25 20 Signal common RC DTE DSR A DCE Ready 4 11 DSR A DCE Mode DM A DTE DSR B DCE Ready 22 29 DSR B DCE Mode DM DCE TXD A Transmit Data B 4 TXD A Transmit Data SD B DCE TXD B Transmit Data 23 22 TXD B Transmit Data SD B 2 SWPIM SY Installation Guide RS449 DTE Cable Table B 3 RS449 DTE Cable Continued Connector 1 P Connector 2 36 Pin Male Conn w Back Shell A DB 37 Pin Male Conn w Back Shell RS449 DTE E RS449 DCE Dir Signal Name Pin Pin Signal Name Mne To monic DTE DCD A Receiver Ready 6 13 DCD A Receiver Ready RR DTE DCD B Receiver Ready 24 N 31 DCD B Receiver Ready RR DCE RTS A Reg to Send 8 7 RTS A Reg to Send RS DCE RTS B Reg to Send 26 25 RTS B Req to Send RS DTE CTS A Clear to Send 9 9 CTS A Clear to Send Cs DTE CTS B Clear to Send 27 27 CTS B Clear to Send Cs DTE RXD A Receive Data 10 6 RXD A Receive Data RD DTE RXD B Receive Data 28 i 24 RXD B Receive Data RD DTE RI Ring Indicator 11 15 RI Incoming Call IC DTE RXC A Receive Timing 13 8 RXC A Receive Timing RT DTE RXC B Receive Timing 31 26 RXC B Receive Timing RT DCE DTR A Terminal Ready 14 12 DTR A Terminal Ready TR DCE DTR B Terminal Ready 32 N 30 DTR B Terminal Ready TR DCE SCTE A Transmit Timing 15 17 SCTE A Terminal Timing TT DCE SCTE B Transmit Timing 33 35 SCTE B Terminal Timing TT DTE TXC A Transmit Timing 17 5 TXC A Send Timing ST DTE TXC
29. e host platform and sliding it in Take care that the SWPIM SY slides in straight and properly engages the backplane host connector Do not force the device SWPIM SY Installation Guide Installing the SWPIM SY Rail Guides Host Platform SSS View of Host Connector End of SWPIM SY SWPIM SY Network Connector End Thumbscrew WENN 9 LNK SWPIM SY 3001 E Figure 1 1 Installing the SWPIM SY into the Host Platform 8 Fasten the SWPIM SY with the thumbscrew 9 Replace power to the host platform if necessary Check to see that the host platform LED indicators go to their normal configuration If they do not remove the SWPIM SY from the host platform and contact Cabletron Systems Do not connect any WAN cables until the SWPIM SY has been LN configured in software The phone company can shut down a line that has an unconfigured connection on it 10 The SWPIM SY must be configured before the WAN connection is made Once the SWPIM SY has been configured the host platform must undergo a soft or hard restart in order for the SWPIM SY to be recognized and for traffic to pass Refer to the appropriate software manual to configure the SWPIM SY SWPIM SY Installation Guide 1 3 Chapter 1 Installation 1 3 LANVIEW LED INDICATIONS Refer to Table 1 1 for the link LED indications for the SWPIM SY The link LED is multicolored and will display different colors and on off rates to indicate diff
30. em e g changing mode switches rebooting the unit etc The serial and revision numbers of all involved Cabletron Systems products in the network A description of your network environment layout cable type etc Network load and frame size at the time of trouble if known The device history i e have you returned the device before is this a recurring problem etc Any previous Return Material Authorization RMA numbers SWPIM SY Installation Guide xvii Introduction xviii SWPIM SY Installation Guide CHAPTER 1 INSTALLATION d Only qualified personnel should install the SWPIM SY This chapter covers the following items e Unpacking the SWPIM SY Section 1 1 e Installing the SWPIM SY into the host platform Section 1 2 e description of the LANVIEW LED indications Section 1 3 e Connecting the SWPIM SY to the network Section 1 4 e What to do once the SWPIM SY is installed Section 1 5 1 1 UNPACKING THE SWPIM SY Use static electricity precautions when handling the SWPIM SY 1 Open the packing box and remove the SWPIM SY 2 Attach the antistatic strap refer to the instructions in the antistatic wrist strap package before removing the SWPIM SY from the antistatic packaging Failure to observe static safety precautions could cause N damage to the SWPIM SY Follow static safety handling rules and wear the antistatic wrist strap shipped with the SWPIM SY Do not cut the non conductive bag to remove t
31. erent situations Table 1 1 Link LED Color Indication Off Disabled or not configured Red No Link Amber Transmit or Receive Traffic Blinking Amber Loopback Test Mode Green Port is Active Blinking Green Port is in test mode 1 4 CONNECTING TO THE NETWORK Figure 1 2 depicts a common configuration for the SWPIM SY It is shown only as an example of a setup used for the SWPIM SY CSU DSU NS SD CSU DSU Site 1 Site 2 SSR 600 7 SSR 600 Va SWPIM SY SWPIM SY Figure 1 2 Common Configuration for the SWPIM SY 1 4 SWPIM SY Installation Guide Completing the Installation Figure 1 3 shows the V 35 cable typically used for connecting the SWPIM SY to the network One end has thumbscrews to attach and the other uses a push release mechanism whereby the connector is removed by squeezing the release buttons Cabletron Part Number 9380413 Figure 1 3 V 35 Cable 1 5 COMPLETING THE INSTALLATION After installing the SWPIM SY the SWPIM SY will need to be configured for the network Refer to the host platform documentation in order to set up and manage the SWPIM SY using the software SWPIM SY Installation Guide 1 5 Chapter 1 Installation 1 6 SWPIM SY Installation Guide APPENDIX A SPECIFICATIONS This section describes the environmental specifications and safety and approval requirements for the SWPIM SY Cabletron Systems reserves the right to cha
32. exception from obtaining such license may be relied upon by the exporting party If the Program is exported from the United States pursuant to the License Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes SWPIM SY Installation Guide Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the technology if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant o r an
33. general working knowledge of WAN and Ethernet and IEEE 802 3 data communications networks and their physical layer components is helpful before using the SWPIM SY STRUCTURE OF THIS GUIDE This guide is organized as follows This Introduction provides preliminary information that will aid in using this manual lists technology and user s guides that may help the user to set up and manage the SWPIM SY and gives an overview of the SWPIM SY and its features and information on how to get help from Cabletron Systems Chapter 1 Installation provides instructions on how to install the device into a host platform and gives the LED indications SWPIM SY Installation Guide Xiii Introduction Appendix A Specifications contains information on functionality and operating specifications connector pinouts for the SWPIM SY environmental requirements and physical properties Appendix B Cables and Pinouts provides Cabletron Systems part numbers and detailed connector and pinout information for the different interface cables used with the SWPIM SY SWPIM SY FEATURES The SWPIM SY can be installed into any Cabletron Systems product that supports the SWPIM architecture such as the SSR 600 or the HSIM SSR 600 The SWPIM SY uses a 36 pin AMP female connector supporting the following electrical signal interfaces e EIA 232 D e EIA 449 e V35 e X2l e EIA 530 e EIA 530A Refer to Appendix B for the Cabletron Systems part numbers
34. he device Damage could result from sharp objects contacting the device or components 3 Verify that the SWPIM SY is undamaged Refer to Getting Help if there is any damage to the device Do not attempt to install the SWPIM SY if it is damaged SWPIM SY Installation Guide 1 1 Chapter 1 Installation 1 2 INSTALLING THE SWPIM SY The SWPIM SY can be installed in any available open slot in the host platform To install the SWPIM SY proceed as follows 1 You do not need to power down the host platform to install the SWPIM SY The SWPIM SY can be installed into the host platform with the power on or off Remove the blank panel covering the slot in the host platform in which the SWPIM SY will be installed by prying it off the faceplate Ensure that the antistatic wrist strap is attached and employed as recommended Observe all precautions to prevent damage from Electrostatic ZAN Discharge ESD 4 Remove the SWPIM SY from the plastic bag Save the bag in the event the device must be removed from the host platform Hold the SWPIM SY with the faceplate facing away right side up from the host platform The 40 pin connector should be facing towards the empty slot with the wide part of the connector oriented down See Figure 1 1 Locate the rail guides inside the slot in which the SWPIM SY will be installed See Figure 1 1 Install the SWPIM SY in the host platform by aligning the SWPIM SY with the rail guides in th
35. interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment uses generates and can radiate radio frequency energy and if not installed in accordance with the operator s manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment SWPIM SY Installation Guide Notice INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des C
36. ir Signal Name Pin Pin Signal Name Mne To monic DTE DSR DCE Set Ready 4 6 DSR DCE Set Ready DCE DTR DTE Term Ready 14 J 20 DTR DTE Term Ready CD DTE CID2 Cable ID 20 21 DTE CID1 Cable ID 2 21 DTE DCEDTE 3 7 Signal Ground 25 1 Signal Ground Signal Common 16 7 Signal Common AB Signal Common 34 23 Signal Common AC Signal DRAIN 1 7 Note For DTE attach DCEDTE pin 3 to pin 7 For Cable ID attach CID2 pin 20 to pin 21 For Cable ID attach CID1 pin 2 to pin 21 SWPIM SY Installation Guide B 11 Appendix B Cables and Pinouts B 8 RS449 DCE CABLE Cable Part Number 9380419 Table B 9 RS449 DCE Cable Connector 1 Connector 2 36 Pin Male Conn w Back Shell DB 37 Pin Female Conn w Back RS449 DCE 4 shell RS449 DTE Dir Signal Name Pin Pin Signal Name Mne To monic Signal Common 25 20 Signal common RC DTE DSR A DCE Ready 14 11 DSR A DCE Mode DM DTE DSR B DCE Ready 32 29 DSR B DCE Mode DM DCE TXD A Transmit Data 10 4 TXD A Transmit Data SD DCE TXD B Transmit Data 28 i 22 TXD B Transmit Data SD DTE DCD A Receiver Ready 6 18 DCD A Receiver Ready RR DTE DCD B Receiver Ready 24 31 DCD B Receiver Ready RR DCE RTS A Req to Send 9 7 RTS A Req to Send RS DCE RTS B Req to Send 27 N 25 RTS B Reg to Send RS DTE CTS A Clear to Send 8 9 CTS A Clear to Send cs DTE CTS B Clear to Send 26 i 27 CTS B Clear to Send CS DTE RXD A
37. nge these specifications at any time without notice A 1 PHYSICAL PROPERTIES Dimensions 1 98 H x 5 40 W x 19 35 D cm 0 78 H x 2 125 W x 7 62 D in Weight Unit 068 kg 0 15 Ib Nominal current draw on 5V supply from host platform 350 mA MTBF Predicted 65 681 445 hours A 2 NETWORK INTERFACE The SWPIM SY uses a 36 pin AMP female connector for the network port that supports the electrical signal interfaces in Table A 1 Table A 1 also shows the minimum and maximum speeds of the Synchronous Asynchronous module Table A 1 Interface Performance Interface Minimum Speed Maximum Speed EIA 232 D 1 2 Kbps 256 Kbps EIA 449 1 2 Kbps 8 Mbps V 35 1 2 Kbps 8 Mbps X 21 1 2 Kbps 8 Mbps EIA 530 1 2 Kbps 8 Mbps EIA 530A 1 2 Kbps 8 Mbps SWPIM SY Installation Guide A 1 Appendix A Specifications The network interface pin assignments for the network connector are listed in Table A 2 Dir To indicates the direction of the signal Table A 2 Network Interface Connector Pin Assignment Signal Dir To Pin GND 1 CIDI_ 2 DCEDTE_ 3 DSR_A DTE 4 TXD_A DCE 5 DCD_A DTE 6 GND 7 RTS_A DCE 8 CTS_A DTE 9 RXD_A DTE 10 RI DTE 11 NC 12 RXC_A DTE 13 DTR_A DCE 14 SCTE A DCE 15 GND 16 GND 34 TXC A DTE 17 TXC B DTE 35 LL DCE 18 RL DCE 36 SHIELD M1 SHIELD M2 Note CIDn Cable Identity n
38. ommunications du Canada NOTICE The Industry Canada label identifies certified equipment This certification means that the equipment meets telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents s The department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate N
39. q to Send RTS A Req to Send RTS B Req to Send RTS B Req to Send RXC A Receive Timing RXC A Receive Timing RXC B receive Timing RXC B receive Timing CID2 Cable ID DCEDTE_ Signal Common Shield DRAIN Signal Common Note For DTE attach DCEDTE pin 3 to pin 7 For Cable ID attach CID2 pin 20 to pin 21 SWPIM SY Installation Guide Appendix B Cables and Pinouts B 6 EIA 530 DTE CABLE Cable Part Number 9380411 Table B 7 EIA 530 DTE Cable Connector 1 P Connector 2 36 Pin Male Conn w Back Shell DB 25 Pin Male Conn w Back EIA 530 DTE shell EIA 530 DCE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Trans Data 5 2 TXD A Trans Data BA DCE TXD B Trans Data 23 14 TXD B Trans Data BA DTE RXD A Rec Data 10 3 RXD A Rec Data BB DTE RXD B Rec Data 28 16 RXD B Rec Data BB DTE CTS A Clear to send 9 5 CTS A Clear to send CB DTE CTS B Clear to send 27 13 CTS B Clear to send CB DCE RTS A Req to Send 8 4 RTS A Req to Send CA DCE RTS B Req to Send 26 19 RTS B Req to Send CA DTE DCD A Carrier Detect 6 8 DCD A Carrier Detect CF DTE DCD B Carrier Detect 24 10 DCD B Carrier Detect CF DTE TXC A Trans Timing 17 15 TXC A Trans Timing DB DTE TXC B Trans Timing 35 12 TXC B Trans Timing DB DTE RXC A Rec Timing 13 17 RXC A Rec
40. the License Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes SWPIM SY Installation Guide vii Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the technology if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant o r any major component of a plant export to Country Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign prod
41. uced direct product is subject to national security controls as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Product i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Cabletron and or its suppliers For Department of Defense units the Product is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 EXCLUSION OF WARRANTY Except as may be specifically provided by Cabletron in writing Cabletron makes no warranty expressed or implied concerning the Program including its documentation and media CABLETRON DISCLAIMS ALL WARRANTIES OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PROGRAM THE ACCOMPANYING WRITTEN MATERIALS AND ANY ACCOMPANYING HARDWARE 7 LIABILITY FOR CONSEQUENTIAL DAMAGES IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIA
42. y 22 23 DTR B DTE Term Ready CD DTE CID1 Cable ID 2 21 DTE CID3 Cable ID 30 21 Signal Ground 25 1 Signal Ground Signal Common 16 7 Signal Common AB Signal DRAIN 1 7 Note For Cable ID attach CID1 42 to pin 21 Cable ID attach CID3 30 to pin 21 SWPIM SY Installation Guide B 19 Appendix B Cables and Pinouts B 13 530 DCE CABLE Cable Part Number 9380421 Table B 14 EIA 530A DCE Cable Connector 1 p Connector 2 36 Pin Male Conn w Back A DB 25 Pin Female Conn w Back Shell Shell EIA 530A DCE R EIA 530A DTE Dir Signal Name Pin Pin Signal Name Mne To monic DCE TXD A Trans Data 10 A 2 TXD A Trans Data BA DCE TXD B Trans Data 28 14 TXD B Trans Data BA DTE RXD A Rec Data 5 B 3 RXD A Rec Data BB DTE RXD B Rec Data 23 16 RXD B Rec Data BB DTE CTS A Clear to send 8 C 5 CTS A Clear to send CB DTE CTS B Clear to send 26 13 CTS B Clear to send CB DCE RTS A Req to Send 9 D 4 RTS A Req to Send CA DCE RTS B Req to Send 27 D 19 RTS B Req to Send CA DTE DCD A Carrier Detect 6 E 8 DCD A Carrier Detect CF DTE DCD B Carrier Detect 24 10 DCD B Carrier Detect CF DTE TXC A Trans Timing 17 F 15 TXC A Trans Timing DB DTE TXC B Trans Timing 35 12 TXC B Trans Timing DB DTE RXC A Rec Timing 15 G 17 RXC A Rec Timing DD DTE RXC B Rec Timing 33 9
43. y major component of a plant export to Country Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Product i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Cabletron and or its suppliers For Department of Defense units the Product is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 EXCLUSION OF WARRANTY Except as may be specifically provided by Cabletron in writing Cabletron makes no warranty expressed or implied concerning the Program including its documentation and media CABLETRON DISCLAIMS ALL WARRANTIES OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PROGRAM THE ACCOMPANYING
Download Pdf Manuals
Related Search