Enterasys ssr-gsx31-04 Expansion Module
Contents
1. O O IL L Y O OIN L Card Guides ra Circuit Card g CULI sL CUO Olole O 1 L r mo L r rl L ri pr L r BE L r aes Siei fol 8 el fells fe fell Metal Plate 8 SlLejleljs Le Lel s Led Ley QOH ORS OFFLINE ONLINE O TROUBLESHOOTING Proper Boot Sequence Offline LED turns on and remains on until card is online Port LEDs turn on momentarily and the CLI indicates that the system discovered the line card in proper slot CLI indicates all ports are initialized and offline LED turns off Online LED lights e Link LED is active for connected lines Common Errors The line card is not inserted properly or seated completely in the chassis Connectors for the connected lines are not seated properly Attached device is not configured to match configuration mode of module i e auto negotiation speed duplex Helpful CLI Commands for Debugging J System show hardware System show version Port show port status gi x y where x is the chassis slot that contains the line card and y is a specific port number on the card e System show bootlog ADDIT2. 39 04 SSR GSX31 04 Quick Start Web Site http www enterasys com 9033748 02 ENTERASYS NETWORKS n
3. Bandwidth Range Connector 62 5 125 um 160 MHz km 2 220 m 7 722 ft SC 200 MHz km 2 275 m 7 902 ft SC 50 125 um 400 MHz km 2 500 m 7 1641 ft SC 500 MHz km 2 550 m 7 1805 ft SC Table 2 1000Base LX Single Mode Fiber Specifications Fiber Diameter Modal Bandwidth Range Connector 62 5 125 um 160 MHz km 2 220 m 7 722 ft SC 200 MHz km 2 275 m 7 902 ft SC 50 125 um 400 MHz km 2 500 m 7 1641 ft SC 500 MHz km 2 550 m 7 1805 ft SC 10 125 um SMF N A 2 5000 m 7 ft 3 1 m SC OPTICS Table 3 1000Base SX Fiber Receiver Sensitivity Transmit Power Minimum 17 dBm Minimum 9 5 dBm Maximum 0 dBm Maximum 4 dBm Table 4 1000Base LX Fiber Receiver Sensitivity Transmit Power Minimum 20 dBm Minimum 11 5 dBm Maximum 3 dBm Maximum 3 dBm LEDs Table 5 LED Indicators LED Condition Status Offline On The line card is offline powered off and ready to hotswap This LED also lights briefly whey you reboot or reset the XP but turns off as soon as the control module discovers the SSR GLX39 04 or SSR GSX3 1 04 Online On The SSR GLX39 04 or SSR GSX31 04 is ready to receive process and send packets if configured Per Port Link Green Indicates that the port hardware detected the cable plugged into the port and a good link is established Intermittent The port received an error during operation Red Red The port hardware detected a cable plugged into the port but a bad link was established Off No link from the port exis
4. IONAL INFORMATION For additional information about installing this module or to learn more about what capabilities are included in the firmware release you are using visit the Enterasys Networks web site Getting Help For additional support related to the Common CLI syntax or this document contact Enterasys Networks using one of the following methods World Wide Web http www enterasys com Phone 603 332 9400 Internet mail support enterasys com FTP fip ftp enterasys com Password your email address To acquire the latest image for http www enterasys com download this product and any available release notes Additional documentation http www enterasys com support manuals To send comments or suggestions concerning this document contact the Technical Writing Department via the following email address TechWriting enterasys com Please include the document Part Number in the email message Before contacting Enterasys Networks for technical support have the following information ready J Your Enterasys Networks service contract number A description of the failure A description of any action s taken to resolve the problem e g changing mode switches rebooting the unit The serial and revision numbers of all involved Enterasys Networks products in the network e A description of your network environment layout cable type etc Network load and frame size at the time of trouble if known SSR GLX
5. NOTICE Enterasys Networks and its licensors reserve the right to make changes in specifications and other information contained in this document without prior notice The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made The hardware firmware or software described in this manual is subject to change without notice IN NO EVENT SHALL ENTERASYS NETWORKS AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT EVEN IF ENTERASYS NETWORKS AND ITS LICENSORS HAVE BEEN ADVISED OF KNOWN OR SHOULD HAVE KNOWN THE POSSIBILITY OF SUCH DAMAGES Enterasys Networks Inc 35 Industrial Way Rochester NH 03866 5005 2001 by Enterasys Networks Inc All Rights Reserved Printed in the United States of America Order Number 9033748 02 October 2001 X Pedition and Enterasys Networks are registered trademarks of Enterasys Networks or its licensors All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies FCC NOTICE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause un
6. desired operation NOTE This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment uses generates and can radiate radio frequency energy and if not installed in accordance with the operator s manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment INDUSTRY CANADA NOTICE This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada VCCI NOTICE This is a class A product based on the standard of the Voluntary Control Council for Interference by Informat
7. dule only in appropriate anti static packaging Equipment Checklist After unpacking SSR GLX39 04 or SSR GSX31 04 check the contents of the box to be sure you received the following items One SSR GLX39 04 or SSR GSX31 04 module in anti static bag One disposable anti static wristband Tools This installation requires the following tools Anti static wristband Phillips screwdriver E Preliminary Setup Firmware Image Requirements Version 8 3 0 0 or later CLI Setup Enter the following commands at the CLI before implementing any configurations 1 Type the following from Enable mode to enter Configuration mode Enable gt Configure 2 You may now begin configuring ports on the SSR GLX39 04 or SSR GSX31 04 Refer to the Enterasys X Pedition Command Line Interface Reference Manual for details Default Module Settings The default mode for each port on the XP 8000 and XP 8600 is Full duplex 1000 mbs autonegotiation on To view the current mode for a particular port enter the following where x is the chassis slot that contains the line card and y is a specific port number on the card XP port show port status gi x y Connector Pin Assignments The connector pins are assigned as follows Table 6 Rx Tx Pin Assignments Pin Connection Rx When mated with the cable connector the SC connector is keyed to run the proper Tx to Rx and Rx to Tx fibers Tx Hotswap You may install this module into a live s
8. ion Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions COM AWLERESERMSAEMMN RAR VCCI OFF CHED VIRZARRNEE CT TOREA KERETEI S ER HHI AMITLCEMHVET COBRICLEAAMBIEHRERT ZLIBRENSTCEMHOVET CLASS A ITE NOTICE WARNING This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures DECLARATION OF CONFORMITY Application of Council Directive s 89 336 EEC 73 23 EEC Manufacturer s Name Enterasys Networks Inc Manufacturer s Address 35 Industrial Way PO Box 5005 Rochester NH 03867 European Representative Name Mr Jim Sims European Representative Address Enterasys Networks Ltd Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England Conformance to Directive s Product Standards EC Directive 89 336 EEC EC Directive 73 23 EEC EN 55022 EN 55024 EN 60950 EN 60825 Equipment Type Environment Networking Equipment for use in a Commercial or Light Industrial Environment Enterasys Networks Inc declares that the equipment packaged with this notice conforms to the above directives AGENCY STANDARDS Safety Meets the requirements of UL 1950 CSA C22 2 No 950 EN 60950 IEC 950 73 23 EEC and EN 60825 Electromagnetic Compatibility Compliant with the requirement
9. s of FCC Part 15 CSA C108 8 EN 55022 VCCI V 3 EN 55024 89 336 EEC and EN 500082 1 SSR GLX39 04 amp SSR GSX31 04 The SSR GLX39 04 and SSR GSX31 04 are 4 port T Series Gigabit Line Cards for the XP 8000 and XP 8600 switch routers The SSR GLX39 04 connects to 1000Base LX fiber and the SSR GSX3 1 04 connects to 1000Base SX fiber SPECIFICATIONS Ports 4 1000Base SX or 1000Base LX SC connectors Network Interfaces SC connector 850 nm Short Wavelength Transceiver SC connector 1300 nm Long Wavelength Transceiver 50 125 um Multimode Fiber Optic Cables 62 5 125 um Multimode Fiber Optic Cables 10 125 um Singlemode Fiber Optic Cables Number of Flows Routes Layer 2 Entries 512 000 memory size 32 MB Layer 3 Entries 256 000 memory size 16 MB Switch Method Address based and Flow based Queue Buffer Packet memory size 8MB Physical Dimensions Size 3 94 cm H x 19 68 W x 27 94 D 1 55 in H x 7 75 W x 11 D Weight 1 4 kg 3 0 Ibs Power Consumption BTU hr 273 63 AC Volt Amps 81 nanan NOTE If your system uses a redundant power configuration or only one power supply you will not be able to support more than 4 cards in the XP 8000 and 10 in the XP 8600 Temperature Operating 41 to 104 F 5 to 40 C Storage 22 to 164 F 30 to 73 C Humidity 15 to 90 non condensing CONNECTIVITY GUIDELINES Table 1 1000Base SX Multi Mode Fiber Specifications Fiber Diameter Modal
10. ts Per port Rx Green The port s transceiver is receiving packets Orange The port s transceiver is receiving flow control packets Per port Tx Green The port s transceiver is transmitting packets Orange The port s transceiver is transmitting flow control packets Per port AN Green The line card auto negotiated the operating mode of the link between full duplex and half duplex Intermittent Auto negotiation is in progress Orange Orange Indicates a problem with auto negotiation configuration Red An auto negotiation failure occurred This fault may occur if the link partner does not support full duplex operation Off Auto negotiation is disabled or the link is down INSTALLING THE MODULE ELECTRICAL HAZARD Only qualified personnel should perform installation procedures saan NOTE You may install the SSR GLX39 04 or SSR GSX31 04 in any line card slot except the CM slot which supports a control module only Handling the Module CAUTION The SSR GLX39 04 and SSR GSX31 04 are easily damaged by electrostatic discharge To prevent electrostatic damage observe the following guidelines Do not remove the module from its packaging until you are ready to install it Do not touch any of the module s pins connectors or components Hold the module only by its edges or front panel Wear an anti static wristband connected to a suitable earth ground whenever handling the module Store or transport this mo
11. ystem without powering off the device However you may not remove an active module from a live system except under the following conditions Press the Hotswap button The Online LED will turn off and the Offline LED will turn on OR Enter the following from the CLI and click enter Enable gt System gt Hotswap gt Out gt Slot gt The Online LED will turn off and the Offline LED will turn on Instructions CAUTION You may install the SSR GLX39 04 or SSR GSX31 04 in the chassis with the chassis powered up However before removing an existing line card hotswap the line card as described previously 1 Ifa cover plate is installed in the line module slot remove the cover plate loosen the captive screws on each side of the coverplate and pull out the plate 2 Align the backsheet of the line card between the card guides as shown in Figure 1 tnssa NOTE Make sure that the circuit card is between the card guides Check both tracks 3 Slide the line card all the way into the slot firmly but gently pressing the line card fully in place to ensure that the pins on the back of the line card are completely seated in the backplane 4 Tighten captive screws Align the captive screws with the holes in the face of the module and tighten the screws to secure the SSR GLX39 04 or SSR GSX31 04 to the chassis 5 Repeat the above steps for additional cards Figure 1 Install the Module fe OGIES O O LIL o fo
Download Pdf Manuals
Related Search