Iwill ZPC-SP (ZPCSP) Barebone
Contents
1. IWILL User s Manual Connect the processor fan cable connector to the motherboard header Secure four screws Align the heatsink and clip assembly with the retention mechanism and place it on the processor Secure four screws to the retention mechanism Align the gasket and place it e MM k t E E e Install the gasket by carefully aligning it to the bottom of heatsink Turn the screw to the right to tighten it 22 User s Manual ZPC Series Hardware Installation Guide Installing System Memory To install a memory module you insert a module into its socket and secure it with the socket retaining arms The modules are notched so that you cannot insert them incorrectly The BIOS recognizes the installed memory and configures the CMOS Setup Utility automatically 1 Unlock a DIMM socket by pressing the retaining clips outward Align the notch on the memory module to the break on the socket Firmly insert the module into the socket until the retaining clips snap back into place and the module is properly seated 4 Make sure the memory module is locked on the socket with both retaining clips Memory Specifications 1 Supports 128MB 256MB 512MB and 1GB modules Maximum 2GB total system memory 2 400MHz PC3200 or 333MHz PC2700 or 266MHz PC2100 DDR SDRAM 3 Dual Channel Modules and the same speed provide better performance Note1 Installing two memory modules is recommended for this moth2. 3 Gently join the another cover to the chassis so that it may 4 Make sure the four screw holes on the chassis cover are be firmly fixed aligned to the holes on the case Tighten the four screws 28 User s Manual ZPC Series Hardware Installation Guide Replace the front panel After you have replaced the cover you are now ready to put the front panel back together Follow these steps to re assemble the system 1 Replace the front panel Make sure the cover locks are 2 Tighten the screw properly clamped in place 2 Carefully replace the front panel Take caution when lifting in the drive assembly you may damage the 4 hry cables connected to the front panel and daughter board bossa User s Manual 29 IWILL 30 User s Manual User s Manual ZPC Series Hardware Installation Guide Chapter 3 The small form factor design of the IWILL barebone system help to maximize work space and compliments your interior design This chapter contains E Positioning the System Unit E Setting Up Your Computer E Arranging your workspace gt O D O j e tF CD op lt U tF CD C F User s Manual 31 IWILL User s Manual Positioning the System Unit The small form factor system is placed on a flat stable surface like an office desk or computer table Your computer may not be equipped with all of the hardware features described in the section The location of the cont
3. How this guide is organized This document contains the following parts 1 Chapter 1 System Introduction This chapter gives a general description of the IWILL book size barebone system It includes introduction on the front and rear panel features and the internal features 2 Chapter 2 System Assembly This chapter tells how to install components into the barebone system through illustrated step by step instructions 3 Chapter 3 Connection Peripherals This chapter detail steps in installing other Peripherals and components that can be included in the system 4 Chapter 4 Mainboard Information This chapter describes proper mainboard placement for system safety and compliment space saving design 5 Chapter 5 BIOS Setup This chapter tells how to change system settings through the BIOS Setup menus It includes detailed descriptions of the BIOS parameters 6 Chapter 6 Drivers and Utilities This chapter gives information about the ZPC Software drivers and utilities operation 7 Chapter 7 Specification This chapter gives information about the ZPC detail specification Illustrations used in this guide 7 WARNING i Information to prevent injury to yourself when trying to complete a task DANGER de Information to prevent damage to the components thr IMPORTANT Information that you MUST follow to complete a task NOTE K Tips and additional information to aid in completing a task Where to find more information
4. IEEE 1394 Two front and rear Headphone One front Microphone Two 1 front and 1 rear Line in Two one front one rear Speaker One rear Serial One rear PS 2 Keyboard One rear PS 2 Mouse One rear Height 245 mm Width 75 mm Depth 355 mm 6 22KG Net weight without CPU RAM HDD CDROM Certification FCC class B CE mark 89 336 ECC EMV User s Manual Hardware Installation Guide 61
5. Refer to the IWILL Websites for additional information and for product and software updates User s Manual 7 IWILL User s Manual Unpacking ZPC Your ZPC may not be supplied with all of the accessories shown depending on the system configuration you purchased For details on the accessories supplied with your computer see the specifications sheet in this manual ZPCsp ZPC64 System unit External Power Adapter Power Cord IDE Power Cord for 2 5 HDD 2 5 HDD Holder Drivers CD User s Manual Quick Installation Guide Heatsink and cooling module have been assembled in the ZPC ST already Use 2 5 HDD holder to replace 3 5 HDD holder when you install longer AGP or PCI card If any of the above items is damaged or missing contact your dealer immediately DVI to D Sub Converter only in ZPCsp version 8 User s Manual ZPC Series Hardware Installation Guide Chapter 1 All about the IWILL ZPC series barebone system the front and rear panel features and the internal layout and design The IWILL ZPC series barebone system includes the IWILL motherboard a power supply accessories and cables built into in a chassis This section shows the various external connectors on your computer to which you can attach external options such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When adding an external opt
6. USB devices Connection for a headphone Connection for microphone The front panel of your ZPC Computer enables access to drives ports and jacks that enable you to connect compatible peripheral devices 10 User s Manual ZPC Series Hardware Installation Guide ZPCsp Rear Panel Features The back panel of your ZPC AP contains the ports for supplied and optional accessories The icons on the back panel locate and identify the ports on your computer Connection for the external power supply Power connector Keyboard port Connection for a PS 2 keyboard SPDIF Out Connection for SPDIF Output S video In jack Connection for an S video cable Empty PCI bracket Connections for PCI devices Monitor DVI port Connection for a DVI monitor w i i Connections for compatible high full Universal Serial Bus 5 mmy f k wa a Wa a low speed USB devices Connections for compatible high full Universal Serial Bus 6 low speed USB devices Mouse port Connection for a PS 2 mouse le CES Serial connector Connections for serial devices Microphone In jack Connection for a microphone Connection for the supplied line out connector sub woofer or optional speakers or headphones line in connector Connection for an audio device Connection for a compatible digital 6 pin IEEE1394 device Connection for a 10BASE T Ethernet port 100BASE TXBASE TX Ethernet Use
7. DR SDRAM One 32 bit PCI 33 MHz slot Onboard 10BASE T 100BASE TX Ethernet port Eight USB 2 0 external ports on rear and front panel Two IEEE1394 6 pin external ports on rear and front panel ZPC64 The ZPC64 barebone Board adopts nVidia nForce3 150 MCP to integrate all system control functions Features of this system include support for AMD Athlon 64 processor 1600 MHz HyperTransport Bus Up to 2GB DDR SDRAM for Dual Channel mode and up to 1GB DDR SDRAM One AGP 8X slot Onboard 10BASE T 100BASE TX Ethernet port Six USB 2 0 external ports on rear and front panel Two IEEE1394 6 pin external ports on rear and front panel For a complete list of specifications see detail specifications 40 User s Manual ZPC Series Hardware Installation Guide ZPCsp Motherboard Photos Here are two photos of ZPCsp motherboard from front and rear side It helps you understand the whole system ZPCsp motherboard front view mA E wi ian E ik C oh plo A al EL me E rim en Gaps Bh Bis 00 71 ESZPCIA AM MILLA mm di i i mig HTI EM YA af a m ara es F ARA AER tel ee Tr User s Manual 41 IWILL User s Manual ZPCsp motherboard rear view 42 Bi F z a z JEES si 16 A rph tf a GU op we HDD tb ah WD ve a Ti Nj a ii MD a DD ib Db ip DD Eb by SLD is eh Ld talline a wt E 3 e fi Bed User s Manual ZPC Series Hardware Installat
8. ZPCsp and ZPC64 Barebone User s Manual Version 1 0 IWILL User s Manual Contents PCC Compliance Statement since ai coce coco gs ieee AA A Carts avenue 4 Disclaimer Trademarks and COPY dara Aaa 5 WVGICOING AA MAIN Taa AWA MITUNA MBI E S ice uaacha seedniems ean head ve SE MAMIA NA buen AYA MAUNO KAME NA JI MU WERE USRESIMUNE ATA 6 ADOULIRIG MANA st il WA IA ua AA Ka 7 ADON AAA 8 Unpacking wi ai WA AA WA KA WAA KA WA SABA li 9 Chapter 1 System MAU WA 11 ZOSP Front Ranel AA AA AAA AS AAA IA AS 12 ZPCsp Rear Patel FOME Sat A AAA a 13 ZrO Front Panel Features id AAA E AA A SO 14 ZR Cet Rear Panel Re AUTOS di A AAA A A Ea 15 Nemal ESAS A e de a la 16 Chapter 2 Assembling the SYSteM ii a 17 REMOVING MS COVE taa AAA AN io 18 Removing Ue WOME DAI iio isa A AA ee eae 19 UANI doler aero 20 Remove e Dase iS nta ir A A dt 21 Remove Ine COOING Sta AA AAA a icasaedae 22 Install ANG Processor IIIA aaa wana 23 IRSTallMa System Memo essa tec odas tada AA a deade a Aed 25 LS talline EA aa 26 STAINING Nal AdS KAVE sneda dentate doetendanssiemorgucesedeaaeeant Caphadduadudy ii 27 Installing ar PENATI ASIA aa irritada 28 Chapter 3 Positioning the SyStemMm wwwwmwwwwmmmamwwwwwwwnmamamumuwuww namimi www nani 33 POSHIONING the SVSTOMI WA aid ota 34 COnmMeCING WIN MONON uscar ASIA aa 35 Connecting the keyboard and Mi ii 36 Connecting ithe Ethemet Calanda 36 COnnecling ne Patada 37 GONnecuUn
9. ave to CMOS and Exit After making your selections in the Setup program save your changes and exit BIOS Setup Select Exit from the main menu and choose the appropriate option Phoenix AwaraBIOS CMOS Setup Utility Quit Without Saving Y N N Esc Quit F9 Menu in BIOS tTleoe Select Item F10 Save Exit Setup 56 User s Manual ZPC Series Hardware Installation Guide Chapter 6 This chapter gives information about the ZPC Software drivers and utilities operation I lt CD x 0 Q o C p CD 0 User s Manual 57 IWILL User s Manual Drivers and Utilities The ZPC series comes bundled with a Power Installer CD ROM disc that includes driver and utility software This chapter describes installing and using this software Running the Power Installer Disc The Power Installer CD ROM install interface runs under Microsoft Windows 9X NT 4 0 2000 or XP After inserting the disc into your CD ROM drive the install interface loads automatically Choose model ZPC from the selections If it does not load run the Power Installer directly from the disc by running Setup Drivers and Utilities Screen This screen has five selections Choose a selection to open its respective screen which are described below The User s Manual selection opens the motherboard documentation Choose Exit to leave this screen Drivers Installation Screen Click Driver Installation in the Drivers and Utilities scree
10. d USB 2 0 ports USB 0 and USB 1 for connecting either USB 1 1 or 2 0 devices to the system It does not matter if the system is on when you connect or disconnect USB devices See the graphic below Audio Jacks The audio jacks are for connecting external audio devices to the onboard audio subsystem The three audio jacks are Line In provides audio input connector for an external audio source Speaker offers output to two stereo speakers Mic this jack is for plugging in a computer microphone User s Manual 45 IWILL User s Manual The differentiate between ZPCsp and ZPC64 rear diagram DC IN s DC IN Power Connector Power Connector AP AGP Expansion 46 User s Manual ZPC Series Hardware Installation Guide Chapter 5 This chapter gives information about the ZPC Basic Input Output System BIOS operation O 0 U D User s Manual 47 IWILL User s Manual BIOS Setup After you have installed peripherals configured the motherboard and assembled the system you can power up the ZPC system The system uses the Award BIOS utility The setup instructions for configuring the system s BIOS Basic Input Output System are contained on this chip The Award BIOS Utility lets you set system parameters which are stored in nonvolatile CMOS RAM This information is retained by battery backup when the system is powered off The values stored in the CMOS configures the system each time the system is power
11. e Enter Select PU PD Yalue F10 Save ESC Exit F1 General Help Fo Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Advanced Chipset Feature Screen Peripherals The Peripherals screen lets you enable and disable onboard peripherals controllers Phoenix AwardBIOS CHOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter Item Help gt Onboard Device gt Superl0 Device Tle Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help Fo Previous Values F6 Fail Safe Defaults F Optimized Defaults Peripherals Screen 52 User s Manual ZPC Series Hardware Installation Guide OnChip IDE Device The OnChip IDE Device screens let you manually or automatically set up different IDE hard drives on two separate IDE channels primary and secondary IDE channels Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode enabled I IDE On Chip Primary PC IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA On Chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Secondary Slave UDMA Tle Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help FS Previous Values F6 Fail Safe Defaults F7 Optimized Defaults OnChip IDE Device Screen Onboard Device The Onboard Device screens let you manually or automatically set up onboard USB function audio functio
12. ed on Running the BIOS Utility The BIOS Utility does not depend on an operating system to run You run the utility by typing the lt Del gt or Delete key before the operating system boots up The BIOS Utility Main Menu appears You navigate the BIOS Utility using keyboard commands that are listed on the lower right portion of each screen Once you have fully configured the BIOS Utility you will rarely need to configure it again Entering Setup Power up the system and press the lt Del gt key to enter the BIOS Setup main menu n entering Setup Main Menu is the first screen displayed Use the UP DOWN arrow keys to highlight the desired menu item and press ENTER to select this item Phoenix AwardBlIOS CMOS Setup Utility Standard CMOS Features Esc Quit F9 Menu in BIOS tl Select Item F10 Save Ex1t Setup BIOS Setup Main Menu Use the arrow keys to select items A description of each selection follows 48 User s Manual ZPC Series Hardware Installation Guide System Information System Information offers general system information such as BIOS information CPU type and speed parallel and serial port I O addresses IDE drive information cache memory size total memory size and memory in each slot Use this information to verify if these components are installed and configured correctly General Configuration The General Configuration screen lets you set time and date settings to suit your locati
13. erboard When installing two modules you must first fill the sockets 1 and 2 Note2 Modules should all be the same manufacture type model and capacity X i MISS User s Manual 23 IWILL User s Manual 1 Install the optical drive and Mini PCl WLAN 2 Remove the CDROM holder 3 Install the mini PC 24 User s Manual ZPC Series Hardware Installation Guide 1 Remove the HDD holder 2 Carefully slip the HDD into the disk drive assembly ill 4 Connect power cable and connect it to the HDD mtg User s Manual 25 IWILL User s Manual 1 Release the PCI AGP bracket 2 Release the screw from the bottom i i 4 Secure the card and bracket with screw 6 Install the card in the expansion slot a a 325 k Ma i Aaa 26 User s Manual ZPC Series Hardware Installation Guide a ZPCsp supports PCI expansion and dose not support AGP expansion it ZPC64supports AGP expansion only PCI Expansion User s Manual AGP Expansion 27 IWILL User s Manual Replace the cover After you have installed all the internal components and you have connected all the necessary cables you are now ready to put the system back together Follow these steps to re assemble the system 1 Replace the cover Make sure the cover locks are properly 2 Gently join the hooks from the cover to the chassis so that clamped in place it may be firmly fixed Mai
14. es and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Move the equipment away from the receiver Plug the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced radio television technician for additional suggestions This device complies with Part 15 of the FCC Rules Operation is subjected to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation C Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Disclaimer 4 User s Manual ZPC Series Hardware Installation Guide The information in this document is subject to change without notice The manufacturer makes no representations or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose F
15. evice settings onboard LAN controller and BIOS write protection Unless you fully understand the function of these settings it is better to leave the default settings Phoenix AwardBLOS CHOS Setup Utility Advanced BIOS Features gt CPU Feature Press Enter gt Hard Disk Boot Priority CPU 11 amp L2 Cache Hyper Threading Technology Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option APIC Hode HPS Version Control For 0 Tlee Move Enter Select PU PD Value FI Save ESC Exit Fl General Help Fo Previous Values F Fail Safe Defaults F7 Optimized Defaults Advanced BIOS Configuration Screen User s Manual 51 IWILL User s Manual Advanced Chipset Features The Advanced Chipset Setup screen configures the DRAM timing clock the memory CAS latency AGP aperture size Unless you fully understand the function of these settings it is recommended that you do not change the default settings Phoenix AwardBIOS CHOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD CAS Latency Time Active to Precharge Delay DRAM RASH to CASH Delay DRAM RASH Precharge System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15H 16M AGP Aperture Size MB Init Display First On Chip YGA On Chip Frame Buffer Size Boot Display Tle Mov
16. f the bottom This frees the chassis cover Disconnect the computer from its power source and from telecommunications links networks or modems before you open the unit or follow any procedures described in this section 16 User s Manual ZPC Series Hardware Installation Guide Remove the base from chassis Release the screw Remove this screw on the front panel This frees the front cover Push down on the latch Push down on the latch to release it Press the latch to remove the front cover User s Manual 17 IWILL User s Manual Opening the chassis Opening the chassis Separate the case and chassis cover Use your thumbs to pull it off from the bottom to the top then lift it off the chassis slightly Gently detach the three front bezel hooks from the case front so that it may be removed Push down on the latch Place the cable of antenna Place the cable of antenna inside the chassis in the appropriate position Remove the front panel Remove the front bezel and set it aside 18 User s Manual ZPC Series Hardware Installation Guide Remove the gasket Release the gaskets Remove screws on gaskets from the bottom This frees the gaskets Gently detach the EMI gaskets from the chassis so that heatsink pipe may be removed Gently remove the cooling system from the motherboard To install the CPU it is necessary to remove the pre installed heatsink assembly User
17. g iNe SCAN isa Ai aa 37 Connecting the POWEr CO sia rd A RA a 38 Arranging YOWE WOIKSDACE ii EIA angst 38 2 User s Manual ZPC Series Hardware Installation Guide Chapter 4 Mainboard Information 4 3 ye ae ee 39 WOMOOUCTION cercare IA EA ic adan iaa 40 ZPGsp Motherboard DROLO tis ccesvs teeta II AE 41 ZPCsp Motherboard DROLO IA Aa 42 ZP Cet Motherboard DROLO Mercurial 43 Zi Cet MONG DO ard PRADO Zinc aii 44 Meal exteral GOnnecior sis ci dei 45 Chapter 5 BIOS SetuP WA 47 Running the BIO SII catas lides 48 GenoralCONAQUra OR aid REA WAUAWA AWA 49 Smart SA AAA EAS ARAS AAA r 50 Advanced BIOS FS atera AA teeuwl RN 51 Advanced Chipset Features ini ida ad 52 A nO AAA WAA AAA AAA cua AA AAA NA AA AAA AA WWW 53 POWer MANA SM ii A A AAA A A 54 PG ee HPP co PORC PERO O OO 55 PCIe alti Wi a raid 55 Load Optimized Detalla a dades 56 Save O O MOS and EA aro IO dla LES 56 Chapter 6 Drivers and Utilities occoooooncccoconcnccnncononooonccononnnccnnoonnnnnncnnnocnnnnnnones 57 Drivers and INNES SM Wan al ii ada 58 Chapter So AA e ts e dd 59 Federal Communications Commission FCC statement User s Manual 3 IWILL User s Manual This equipment has been tested and found to comply with limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates us
18. highs are parallel to the floor and your feet are either flat on the floor or on a footrest When using the keyboard keep your forearms parallel to the floor and your wrists in a neutral comfortable position Adjust the monitor so the top of the screen is at or slightly below eye level m Place the LCD monitor at a comfortable viewing distance usually 50 to 60 cm Also position other equipment you use regularly such as the telephone or a mouse within easy reach User s Manual 37 IWILL 38 User s Manual User s Manual ZPC Series Hardware Installation Guide Chapter 4 This chapter gives information about the IWILL motherboard that came with the system This chapter includes the motherboard layout jumper settings and connector locations lt v O gt O O at 5 User s Manual 39 IWILL User s Manual Introduction The ZPC mainboard is a high performance motherboard that supports the Intel Pentium 4 processor with 478 pin socket or AMD Athlon 64 CPU with 754 pin socket This board has two DIMM memory sockets that accommodates dual channel 400 MHz DDR SDRAM and AGP or PCI for future expansion ZPCsp The ZPCsp barebone Board adopts Intel 865GV chipset to integrate all system control functions Features of this system include support for Intel Pentium 4 processor up to 3 4GHz 800 533 MHz system bus Up to 2GB DDR SDRAM for Dual Channel mode and up to 1GB D
19. hout CPU RAM HDD CDROM Certification FCC class B CE mark 89 336 ECC EMV 60 User s Manual User s Manual ZPC Series ZPC64 Specifications Processor Memory Chipset Ethernet USB 2 0 Firewire Drive Bay Expansion PSU Audio I O ports Dimension Weight Supports AMD Athlon 64 Socket 754 with 1600 MHz Hyper Transport Supports Athlon 64 with maximum to 3400 DDR400 333 SDRAM Support Unbuffer DDR SDRAM Total memory slots two DIMM Maximum memory expansion 2GB nVIDIA nForce 3 150 MCP TI IEEE1394 Host Controller NV MAC Realtek RTL8201BL PHY nVidia MAC 10 100 Ethernet Realtek RTL8110S 10 100 Mb Six USB 2 0 Offer up to 480MB s Two USB 2 0 external ports on the rear panel Four USB 2 0 external ports on the front panel IEEE1394 1394A compliant OHCI compatible programming interface Two IEEE1394 ports on the front and rear panel 100 200 400 Mbps data transfer rates One 3 5 drive bay for IDE HDD Or Two 2 5 drive bay for IDE HDDs One internal drive bay for slim line optical driver One AGP 8X slot available One Mini PCI slot 220 Watt External Power Supply AC Input from 115 230V by 60 50Hz Fully support ATX specification Certification RU TUV CE FCC 6 Channel Audio utilizes the Realtek ALC655 codec Provides Superior Surrounding sound Line in Speaker Mic on rear panel Earphone Mic on front panel SPDIF optical audio In Out USB 2 0 Six 4 front and 2 rear FireWire
20. inter E Plug the USB cord into the back of the computer E Plug both the USB to printer and printer s power cords into a grounded AC wall outlet Connecting the Scanner E Plug the USB cord into the back of the computer E Plug both the USB to scanner and scanner s power cords into a grounded AC wall outlet User s Manual 35 IWILL User s Manual Connecting the Power Cords Plug the power adapter into the back of the computer Connecting the Speakers E Plug the cable attached to the back of the speaker into the Red Speaker jack on the back of the right speaker E Insert the yellow plug of the speaker power cable into the DC In jack yellow on the back of the right speaker E Insert the black plug of the speaker power cable into the DC Out jack located on the back panel of your computer Connector 36 User s Manual ZPC Series Hardware Installation Guide Arranging your workspace Here are some guidelines to help you find better way to use your computer Viewing Distance Lower Back Support Seat Height Sitting in the same position for a long time can cause fatigue m A good chair can make a big difference The backrest and seat should adjust independently and provide good support m The seat should have a curved front to relieve pressure on the thighs Adjust the seat so that your t
21. ion 2GB North Bridge Intel 865GV South Bridge ICH5 VIA 6306 IEEE1394 Host Controller Realtek 8100B Fast Ethernet Controller Integrated Intel Extreme Graphics II Rapid Pixel Rendering Intel Dynamic Video Memory Technology DVI digital monitor outputs Realtek 8100B 100Mbps and 10Mbps Fast Ethernet operations Eight USB 2 0 Offer up to 480MB s Four USB 2 0 external ports on the rear panel Four USB 2 0 external ports on the front panel IEEE1394 1394A compliant OHCI compatible programming interface Two IEEE1394 ports on the front and rear panel 100 200 400 Mbps data transfer rates One 3 5 drive bay for IDE HDD Or Two 2 5 drive bay for IDE HDDs One internal drive bay for slim line optical driver One 32 bit 33MHz PCI slot One Mini PCI slot 220 Watt External Power Supply AC Input from 115 230V by 60 50Hz Fully support ATX specification Certification RU TUV CE FCC 6 Channel Audio utilizes the Realtek ALC655 codec Provides Superior Surrounding sound Line in Speaker Mic on rear panel Earphone Mic on front panel SPDIF optical audio In Out USB 2 0 Eight 4 front and 4 rear FireWire IEEE 1394 Two front and rear Headphone One front Microphone Two 1 front and 1 rear Line in Two one front one rear Speaker One rear Serial One rear PS 2 Keyboard One rear PS 2 Mouse One rear DVI One rear S Video One rear Height 245 mm Width 75 mm Depth 355 mm 6 22KG Net weight wit
22. ion use the information in this section to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Y lt Y F D 3 F x O Q C O Use your hand fingertip to push open the front panel cover User s Manual 9 IWILL ZPCsp Front and Rear Panel Features User s Manual The front panel of ZPCsp features a slim line bay for optical disk drive Microphone Earphone SPDIF Out 6 pin Firewire jacks and USB2 0 connectors Power switch Optical drive System Indicator HDD access indicator Universal Serial Bus 1 Universal Serial Bus 2 A A 7 TEE a System Reset SPDIF In Universal Serial Bus 3 Universal Serial Bus 4 headphone connector microphone connector Turns the computer on and off Slimline drive bay for optical drive The indicator light is amber when the computer is placed in Stand by mode Light is amber while reading and writing data from and to the hard disk Connections for compatible high full low speed USB devices Connections for compatible high full low speed USB devices Connection for a compatible digital device Reset the System Connection for SPDIF Input Connections for compatible high full low speed USB devices Connections for compatible high full low speed
23. ion Guide ZPC64 Motherboard Photos Here are two photos of ZPCe4 motherboard from front and rear side It helps you understand the whole system ZPC64 motherboard front view wy rest 9 1 sa 22 28 Tu e h itb 6 User s Manual 43 User s Manual IWILL ZPC64 motherboard rear view gt DONNA 1 nrsrnrsrnrrnanas seso se 46004404 BRL BAODABAADARARCA A BOS0 A ee ee eteeereenseeeneereeeeseneePeeee E E see gt E 560 O 6464064440440 0900048 4 EA AA AAA AAA AAA A AA A A Gay al TIT 4 IY eaae e aa eeceeeeetceeeeceeeee eee 6064 0081400004 GC E A E E E E A E E E E gt A AA A MA A AAA eeeeeeeeeceeeeeeeee User s Manual 44 ZPC Series Hardware Installation Guide Rear External Connectors This chapter describes the external connection of the ZPC Series PS 2 Ports The PS 2 ports are for a system keyboard and mouse or other tracking device It is recommended that you do not plug or unplug devices when the system is on Serial Port The COM Serial port has a 9 pin connector and can operate at speeds up to 115 200bps Do not connect or disconnect a serial port when the system is turned on VGA Port The VGA port is a 15 pin connector for attaching a VGA monitor Ethernet Ports The LAN Ports is RJ 45 connectors for standard Cat 5 LAN cabling The connectors attach to the onboard 10 100 LAN controllers respectively USB Ports There are four high spee
24. ional accessories The icons on the back panel locate and identify the ports on your computer Power connector Keyboard port Serial connector Empty AGP bracket hat Microphone In jack line out connector cod fed line in connector SPDIF Out 6 pin IEEE1394 ER ES Sd Universal Serial Bus 5 Serial connector TV In Connector Optional Ethernet port User s Manual Connection for the external power supply Connection for a PS 2 keyboard Connections for serial devices For AGP 8X Card expansion Connection for a microphone Connection for the supplied sub woofer or optional speakers or headphones Connection for an audio device Connection for SPDIF Output Connection for a compatible digital device Connections for compatible high full low speed USB devices Connection for a PS 2 mouse Connections for serial devices Connection for an mini PCI TV Tunner Card Optional Connection for a 10BASE T 100BASE TXBASE TX Ethernet 13 IWILL User s Manual Internal Features The figure below shows the system from side The standard components CPU Heatsink power supply are already installed VE OTE TE IY Vs AN TS A IM rA j Hi 14 User s Manual ZPC Series Hardware Installation Guide Chapter 2 Step by step instructions on how to install basic components This section outlines how to install and configure you
25. n and onboard Gigabit LAN function Phoenix AwardBIOS CHOS Setup Utility Onboard Device USB Controller Enabled Item Help USB 2 0 Controller USB Keyboard Support USB Mouse Support AC9 Audio CSA LAN Giga LAN Tle Move Enter Select PU PD Value F1 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults Onboard Device Screen User s Manual 53 IWILL User s Manual SuperlO Device The SuperlO Device screen let set up onboard FDC function Onboard Serial Port and Power On Setting Phoenix AwardBIOS CHOS Setup Utility Superl0 Device POWER ON Function BUTTON ONLY KB Power ON Password Hot Key Power ON Onboard FDC Controller Onboard Serial Port 1 PWRON After PWR Fail Tle Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help Fo Previous Values F6 Fail Safe Defaults F Optimized Defaults SuperlO Device Screen Power Management The Power Management screen lets you configure power management settings Phoenix AwardBI0S CHOS Setup Utility Power Management Setup Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Suspend Mode HDD Power Down Sof t Off by PWR BITN Wake Up by PCI card Power On by Ring Wake Up On LAN Resume by Alarm Primary IDE 9 Tle Move Enter Select PU PD Value F1 Save ESC Exit F1 General Help Fo Previous Values F6 Fail Safe Defaults F Optimized Defaults 54 User
26. n and the Driver Installation screen appears Choose drivers in sequence to open their respective install programs Select the installation guides to review installation information When you are finished click Exit to leave this screen Software Utility Screen Click Software Utility in the Drivers and Utilities screen and the Software Utility screen appears To install the Adobe Acrobat Reader software click on the item you wish to install and follow the instructions Clicking on the Hardware Monitor Utility lets you install a program that gives access to information detected by the hardware monitor Make Driver Screen Click Make Driver in the Drivers and Utilities screen and the Make Driver utility screen appears This utility gives you a convenient way to make driver floppy disks You can use this utility to make driver disks for the LAN driver 58 User s Manual ZPC Series Hardware Installation Guide Chapter 7 This chapter gives information about the ZPC detail specification 0 a D O Q O User s Manual 59 IWILL ZPCsp Specifications Processor Memory Chipset Graphics Ethernet USB 2 0 Firewire Drive Bay Expansion PSU Audio I O ports Dimension Weight Supports Intel Pentium 4 CPU with 800MHz System Bus Supports Pentium 4 Prescott Core with maximum to 3 4GHz of speed DDR400 333 SDRAM Support Unbuffer DDR SDRAM Total memory slots two DIMM Maximum memory expans
27. nding thermal solution as standard equipment And of course they come with FireWire 400 ports High Speed USB2 0 PCI or AGP expansion optical S PDIF front headphone and microphone and built in Ethernet all as standard equipment All models are WiFi ready and offer AccessPoint capability as a option The Intel based ZPCsp The Intel based ZPCsp based on Intel 865G chipset supports Intel Pentium 4 processors Expandable to 2GB dual channel 400MHz DDR with 800MHz system bus IEEE1394 USB2 0 6 Channel Audio SPDIF In Out 10 100mbps Ethernet and One PCI expansion slot The AMD based ZPC64 ZPC64 based on nVidia nForce 3 150 MCP supports AMD Athlon 64 Socket 754 processors with high speed Hypertransport 2 x 400MHz DDR memory IEEE1394 USB2 0 6 Channel Audio SPDIF In Out 10 100mbps Ethernet and One AGP 8X expansion slot The information provided here is designed to help you to become familiar with the design and hardware in your system With the user s guide s step by step instructions chassis installation can never be easier Read this manual which provides updates and supplemental information about your computer Audience This guide provides general information and installation instructions about the IWILL ZPC series Barebone System This 6 User s Manual ZPC Series Hardware Installation Guide guide is intended for experienced users and integrators with hardware knowledge of personal computers
28. on Set boot devices in the appropriate sequence Power up options include Numlock Primary VGA and Boot Sector protection You can set a User and Supervisor password after enabling the Password Required item Forgot the Password If you forget the password you can clear the password by erasing the real time clock s CMOS RAM You can erase the CMOS RAM using the JCMOS1 jumper see Appendix 1 Hardware Layout After you have done so hold down the lt Del gt key during boot up and enter BIOS setup to reenter user preferences Phoenix AwardBIO0S CMOS Setup Utility Standard CMOS Features Time hh mm ss IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive Drive B Video Halt On Tle lt Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help FS Previous Values F6 Fail Safe Defaults F7 Optimized Defaults General Configuration Screen User s Manual 49 IWILL User s Manual Smart Setting Smart Setting allows users to enable CPU or memory options for over clocking 865 Turbojet option will enhance the system memory performance if enabled Items under On chip Serial ATA Setting allow users to enable disable on board Serial ATA function and set up the Serial ATA port mode if enabled Smart Setting Screen 50 User s Manual ZPC Series Hardware Installation Guide Advanced BIOS Features The Advanced BIOS Configuration sets CPU L1 and 2 cacheable booting disk d
29. r ZPC Refer to the following mainboard layout to help you to identify various jumpers connectors slots and ports Then follow these steps designed to guide you through a quick and correct Installation of your system IWILL has designed the ZPC for an IWILL motherboard only It is not advisable to install other motherboards Always turn the power off before you open the system or connect your computer to peripheral equipment Otherwise damage may occur to the integrated circuits in your computer Electrostatic discharge ESD may damage HDDs and other components Follow the procedures described here only at an ESD workstation Ground yourself by maintaining continuous contact with an unpainted metal portion of the chassis while installation gt 0 0 D ez O F D p lt 0 e D User s Manual 15 IWILL User s Manual Removing the cover 1 Disconnect all cables attached to the computer This includes power cords input output 1 0 cables and any other cables that are connected to the computer 2 Remove the WLAN antenna on the top of the computer 3 Release the three screws at the rear of the left side cover 4 Separate the case and chassis cover use your thumbs to pull it off from the front to the back then lift it off the chassis Remove the base from chassis Remove the base Push down on the latch to release it Release the screws Remove the four screws on each end o
30. r s Manual 11 IWILL ZPC64 Front and Rear Panel Features User s Manual The front panel of ZPCe4 features a slim line bay for optical disk drive Microphone Earphone SPDIF Out 6 pin Firewire jacks and USB2 0 connectors Power switch Optical drive System Indicator HDD access indicator Universal Serial Bus 1 Universal Serial Bus 2 A A 7 TEE a System Reset SPDIF In Universal Serial Bus 3 Universal Serial Bus 4 headphone connector microphone connector Turns the computer on and off Slimline drive bay for optical drive The indicator light is amber when the computer is placed in Stand by mode Light is amber while reading and writing data from and to the hard disk Connections for compatible high full low speed USB devices Connections for compatible high full low speed USB devices Connection for a compatible digital device Reset the System Connection for SPDIF Input Connections for compatible high full low speed USB devices Connections for compatible high full low speed USB devices Connection for a headphone Connection for microphone The front panel of your ZPC Computer enables access to drives ports and jacks that enable you to connect compatible peripheral devices 12 User s Manual ZPC Series Hardware Installation Guide ZPC64 Rear Panel Features The back panel of your ZPCex contains the ports for supplied and opt
31. rols ports and jacks may vary from the illustrations shown See the Specifications for your system s specific hardware configuration 32 User s Manual ZPC Series Hardware Installation Guide Setting Up Your Computer Connecting a Display Monitor E Plug the display s cable into the monitor port E f necessary plug the display s cable into the rear of the display cn CREARA kununua ANTE VGA DVI If your monitor has a VGA connector and the optional video card is present connect your monitor to the optional video card connector using the DVI adapter included DVI DVI If your monitor has a DVI connector connect your monitor to the optional video card connector User s Manual 33 IWILL User s Manual Connecting the Keyboard and Mouse E Plug the keyboard cable into the keyboard port on the back of the computer E Plug the mouse cable into the mouse port on the back of the computer Connecting the Ethernet cable m Plug the LAN cable into the LAN jack located on the back panel of your computer E Plug the other end of the LAN cable into the wall jack 34 User s Manual ZPC Series Hardware Installation Guide Connecting the pr
32. s Manual ZPC Series Hardware Installation Guide PCI amp PnP The PCI amp PnP screen configures Plug and Play and other PCI bus settings Phoenix AwardBIOS CHOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Item Help Resources Controlled By PCI VGA Palette Snoop PCI SLOT1 Mini PCI Onboard 1394 Onboard PCI LAN Card Tle Move Enter Select PU PD VYalue F10 Save ESC Exit F1 General Help Fo Previous Values F6 Fail Safe Defaults F Optimized Defaults PCI amp PnP Screen PC Health Status The PC Health Status screen shows information on the system s voltages fan rotations and temperatures Phoenix AwardBI0S CMOS Setup Utility PC Health Status Sysfan Speed Item Help Smart Fan2 Temperature Fan2 Tolerance Value Tle Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help Fo Previous Values F6 Fail Safe Defaults F Optimized Defaults Hardware Monitor Screen User s Manual 55 IWILL User s Manual Load Optimized Defaults The Optimized Defaults Settings screen lets you reload the original manufacturer settings The Restore Optimized Defaults lets the system start using the most reliable settings Use this option when you can no longer boot the system due to changing adding or removing hardware parts or peripherals Phoenix AwarcBIOS CMOS Setup Uti Esc Quit F9 Menu in BIOS F10 Save amp Exit Setup Restore Default Settings Screen S
33. s Manual 19 IWILL User s Manual Disconnect the power cord from the mainboard Disconnect the CPU fan power cable The figure left shows the system from above The standard CPU Memory and SlimLine optical drive are need to be installed Lift Socket Lever Lift the load plate By pressing the socket lever sideways then lift it up to a 90 100 angle Do not touch the socket contacts Before installing or removing the processor make sure AC power has been removed by unplugging the power cord from the computer the standby power LED should not be lit Failure to do so could damage the processor and the board 20 User s Manual ZPC Series Hardware Installation Guide Carefully insert the CPU into the socket until it fits in place Es Make sure that the socket lever is LW yl ps lifted up to 90 100 angle otherwise the CPU does not fit in completely AS Install the processor by carefully aligning the pins to the socket The CPU fits only in one correct orientation DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU When the CPU is in place press it firmly on the socket while you push down the socket lever to secure the CPU The lever clicks on the side tab to indicate that it is locked Apply thermal cream on CPU Use the enclosed syringe and apply some thermal interface material to the top of the processor as shown in left photo User s Manual 21
34. urthermore the manufacturer reserves the right to revise this publication or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision Trademarks Microsoft and Windows are registered trademarks of Microsoft Corp Intel and Pentium 4 are registered trademarks of Intel Corporation Other product names used in this manual are the properties of their respective owners and are acknowledged Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without the express written consent of the manufacturer IWILL Copyright 2003 Welcome User s Manual 5 IWILL User s Manual Thank you for purchasing a ZPC series desktop PC The ZPC features the IWILL mainboard power supply cooling system and other quality components It is ideal for the end users to make a complete understanding about this model The advanced users can also get help while studying this manual The ZPC product line comes in two muscular configurations Intel 865G for Intel Pentium 4 and nVIDIA nForce 3 for AMD Athlon 64 CPUs They all feature the high performance motherboard high quality power supply stylish anodized aluminum alloy enclosure designed and outsta
Download Pdf Manuals
Related Search