Daewoo DWC-052C Air Conditioner
Contents
1. A CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame WINDOW KIT FRAME To provide a proper seal pull each expandable side Window Shutter out Screw Type C and up until it is tight against the window frame Using the hole in the top ss SHUTTER and bottom of each Window Kit Frame as a guide secure Window Kit Suse Frame in window sash and on the window sill WINDOW T Screw Type C INNER WINDOW SILL Step 6 Recheck Installation To be sure you have correctly installed your Room Air Conditioner review the steps and make sure all of the parts are securely fastened in the window as the instructions show A tight seal is essential Read through the Use amp Care manual to become familiar with the operation of your room air conditioner A CAUTION Do not lift window sash without holding the unit The window sash helps keep the unit in the window Exercise caution when opening the window Failure to do so many result in personal injury and or property damage e Step 7 Recheck the Entire Installation TOP GUIDE WINDOW KIT FRAME TLC WINDOW SEAL A WINDQW SEAL gt WINDOW SASH e Screw Type C 2 pieces WINDOW KIT R amp L Screw Type D 2x3 6 pieces GUIDE LOWER2. H LOW FAN Select this setting for quiet air circulation without cooling Fan Cool HIGH COOL Select this setting for cooling operation with HIGH FAN LOW COOL Select this setting for cooling operation with LOW FAN Selector TEMPERATURE CONTROL Choose a temperature settings by rotating the knob of thermostat to the appropriate position ANOTE Setting the control at the coldest extreme of the temperature range will not cool the room any faster Usually the midpoint is a good starting position If the room temperature is not satisfactory after a reasonable period of time adjust the temperature control to a lower or higher The Thermostat automatically starts and stops cooling operation in order to keep the room temperature at a proper level and this results in efficient use of power and economical cooling Turn clockwise for a cooler room temperature Turn counter clockwise for a warmer room temperature Thermostat GENERAL INFORMATION CHANGING AIR FLOW DIRECTION Air flow deflectors divert air from center flow to left or right Adjust deflectors for desired air flow pattern AIR FLOW AROUND UNIT Check in door grill and outdoor louvers for air flow obstructions Do not block air flow to and from unit The outdoor coil should be checked and periodically cleaned for debris that may collect and block unit air flow If air flow is obstructed or deflected back into unit the compressor may cycle on and off rapi
3. Screw Type C 2 pieces SILL SILL BRACKET 1 piece Leveling Screw Type A 1 piece Screw Type B 2 pieces OUTER WINDOW SILL WALL NAMES OF MAJOR COMPONENTS OKO D e 1 D D AZ 22 4 2 7 PART PART 1 7 AIR INTAKE 2 BLADE VERTICAL 8 AIR FILTER 3 COOL AIR DISCHARGE 9 CONTROL PANEL 4 GRILLE FRONT 10 PLATE WINDOW TOP 5 KNOB THERMOSTAT 11 FRAME WINDOW KIT 6 KNOB SELECTOR 12 SHUTTER WINDOW O PERATING INSTRUCTIONS ANOTE FOR MOST ECONOMICAL USE 1 Properly control the room temperature 2 Avoid the unit being exposed to direct sunlight Keep direct sunlight from the room 3 Do not leave doors and windows open amp COOLING CONTROL The Fan Control Selector Switch has five positions Choose one of the speed settings by rotating the fan control Selector Switch to the appropriate position A CAUTION When the air conditioner has been performing its cooling operation and is turned OFF or set to the position wait at least 3 minutes before resetting to the cooling operation m ps T OFF Select this setting for stop all operation of air conditioner Fan Cool HIGH FAN Select this setting for maximum air circulation without cooling
4. YNIT SILL BRACKET Pe Screw Type A OUTER SS E j SILL INNER WINDOW SILL Step 3 Placing Unit in Window A CAUTION 1 The unit is heavy To avoid injury or accident it is strongly recommended that you have additional help when lifting the unit 2 Personal injury or property damage may result if unit falls from window 1 Insert Window Kit Frame into the upper and bottom guides of the unit 2 Fasten window shutter in the window kit frame with Screws Type D in the left side and right side of the unit 3 Open the window and place the unit in the center of the window sill o bottom guides crew Type D 9 Step 4 Install Sash Bracket A CAUTION Do not drill into window frame until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located the frame Fasten Sash Bracket with Screw Type C to top of indoor ASH window sash or directly into side of window sash or directly BRACKET WINDOW into side of window frame FRAME This will prevent the raising of the window from the outside If WINDOW you have a hard wood or metal window frame a 1 8 inch pilot SASH S hole may be needed in order to drive the screw Screw Type C Step 5 Secure Window Shutter
5. cooling Compressor lockout on initial plug in Dirty air filter Is there anything blocking the front Thermostat is not adjusted correctly Air conditioner undersized for application Wait 3 to 4 minutes and restart the unit Clean air filter When blocked by curtains blinds or furnitures etc the air flow is restricted and cooling performance is affected Adjust thermostat correctly Check with dealer to determine proper unit capacity for application Noisy unit Loose parts Weak building construction Water hitting fan Tighten any loose parts Provide additional support Normal in high humidity Stop noise by allowing water to drain from base fan through drain hole Ordors from unit Mold mildew or algae formation on wet surfaces Place algaecide tablet in base pan Remove water in base pan through drain hole Water in base pan Normal for operation in humid areas Water in base pan is picked up by the fan blade and thrown onto the warm outdoor coil where water then evaporates 13 Limited Warranty DAEWOO DAEWOO ELECTRONICS CORPORATION OF AMERICA warrants the following window room air conditioner to be free from defective material and workmanship and agrees to remedy any such defect or to furnish a new part at the Company s option in exchange for any part of any unit of its manufacture which under normal
6. installation use and service disclosed such defect provided the unit is delivered by the owner to store or dealer where purchased or Daewoo authorized service center To establish and receive warranty service at our store dealer or our authorized service center a sales receipt or bill of sales is required for proof of purchase This warranty does not extend to any of our electronic products which have been subjected to misuse neglect accident incorrect wiring not our own improper installation unauthorized modification or to use in violation of instructions furnished by us nor units which have been repaired or altered outside of our factory nor to cases where the serial number thereof has been removed defaced or changed This warranty is in lieu of all warranties expressed or implied and no representative or person is authorized to assume for us any other liability in connection with the sales of our electronic products Over the counter exchange for units that are initially defective Initial defective is described as when the dealer opens the unit and finds that it is inoperative or an individual customer opening a new unit and finding that it is initially defective This unit may be returned to the factory by the dealer for exchange Under no circumstances will an individual customer be permitted to return defective unit directly to factory Exchange must be directly with the dealer When this unit is returned to dealer a copy of the
7. purchase evidence stating the date of purchase is to be put in the individual box for dealer s further control with the factory MODEL PARTS LABOR COMPRESSOR DWC 052C DWC 060C 1 year 1 year 5 years Note The warranty service center list is constantly changing with the addition of our current qualified service centers If there is inadequate or no local service facility subject individual customer will call DAEWOO on the toll free number 1 800 DAEWOOS 1 800 323 9668 to be provided with further informations ROOM AIR CONDITIONER USE amp CARE MANUAL WINDOW TYPE ROOM AIR CONDITIONER DWC 052C DWC 060C UL and CUL listed LISTED Please read carefully and thoroughly this manual before operating the unit If you still have any difficulties or problems consult your dealer for help or DAEWOO ELECTRONICS Please keep this manual well
8. AIR FLOW DIRECTION AIR FLOW AROUND UNIT 6 CARE AND MAINTENANCE 2 11 AIR FILTER CLEANING THE AIR CONDITIONER 7 ELECTRICAL REQUIREMENTS nre er tt eee e ree t RE ne de 12 ELECTRICAL GROUNDING INSTRUCTIONS USE OF EXTENSION CORD 8 BEFORE CALLING FOR 13 GENERAL SPECIFICATIONS DWC 052C DWC ITEM 05 060 POWER SOURCE AC 115V 60Hz SINGLE PHASE 17 3 W x 12 3 H x 15 2 D inch DIMENSIONS 440 W x 313 H x 385 D mm WEIGHT NET 45 4 Ibs 20 6 Kg Approx 46 3 Ibs 21 Kg Approx 2 INSTALLATION INSTRUCTIONS e WINDOW REQUIREMENTS These instructions are provided for a standard double hung window or mobile home double hung window installation in windows 21 7in 550mm to 34 6in 880mm The upper and lower x x sash must open sufficiently to allow a clear vertical opening of 12 7in 323mm from the bottom of the sash to the window stool Select a centrally located window on the side of the room that Eom a receives the least direct sunlight There should be no obstruction to TOME air flow either inside i e curtains or outside i e fence wall or i bushes EX m Read this entire installation manual thoroughly before beginning the installation sure you have the necessary tools and other materials for the j
9. PRECAUTIONS FOR PRO PER USE OF AIR CONDITIONER Please observe the following instructions 1 Operate the Selector Switch to run or stop the unit Do not use Main Power Switch or Auxiliary Power Switch to operate unit 2 Do not stick anything into the air outlet or inlet It is dangerous and it can cause injury or damage 3 Avoid exposing your body directly to a continuous cool air flow for long periods It is not good for your health 4 Do not pour water on the unit to clean it It is dangerous and it can cause injury or damage Never use solvents or harsh chemicals when cleaning the unit When the air inlet grill and cabinet are dirty wipe with luke warm water below 104 F or 40 C 5 Avoid placing any obstacles near the inlet or outlet f the inlet or outlet is blocked with any obstacle it may cause damage to the unit 6 Do not or stop the unit frequently If you run or stop the unit more then 4 5 times an hour it can cause damage to the unit 7 Wait atleast 3 minutes before restarting the unit or in the case of power failure If you turn on the unit within 3 minutes after power off this can cause damage to the unit 8 If the air conditioner is operated without an air filter dust is not removed from the air and resultant accumulation in the unit may lead to a failure Do not forget to install the air filter 9 The air filter should be cleaned at least once every two weeks 10 When the un
10. afety and protection this air conditioner is equipped with a special three prong grounding plug on the service cord A WARNING Do not under any circumstances cut or remove the grounding prong on the plug To do so will create a shock hazard Your air conditioner must be plugged into a properly grounded and polarzied three prong receptacle Do not use an adapter plug If the wall receptacle you intend to use will not accept a three prong plug or if you are not sure the outlet is adequately grounded or protected by a fuse or circuit breaker have a qualified electrician install the proper oulet according to the National Electric Code and applicable local code Step 1 Prepare Components For Installation 1 Open the components box for installation SCREW TYPE 2 Check components for installation as follows Tyne A Sill Bracket 1 piece Window Shutter 2 pieces e Sash Bracket 1 piece g Window Kit Frame Left side 1 piece Window Kit Frame Right side 1 piece Leveling Screw M8 x 45 1 piece 11 4 inch Screw 5 x 30 2 pieces 8 45 5 30 16 MA 8 5 8 inch Screw 4 x 16 5 pieces OTF 1 2 5 6 5 16 inch Screw M4 x 8 6 p
11. dly causing early compressor failure 10 CARE AND MAINTENANCE A CAUTION To avoid death or personal injury due to electrical shock turn fan control OFF and unplug power cord before cleaning or performing maintenance After cleaning or performing maintenance reconnect power AIR FILTER Clean the air filter which removes dust inside the room It should be washed at least once every week during operation 1 Remove the Air Filter from the front grill by pulling up 2 Clean Air Filter with a vacuum cleaner or lukewarm soapy water 3 Shake it when clean to remove moisture completely Replace it NOTE A dirty Air Filter reduces air flow and the cooling capacity Do not operate unit without Air Filter CLEANING THE AIR CONDITIONER 1 At least once a year remove cabinet and thoroughly clean air conditioner Have the unit inspected by an authorized service man to ensure unit is functioning properly 2 Wash air conditioner with lukewarm soapy water as needed Rinse and dry thoro
12. ghly 3 If using concentrated liquid detergent dilute in warm water first 4 Front grill may be wiped off with a cloth dampened in a mild detergent solution 5 Cabinet may be washed with mild soap or detergent and lukewarm water then polished with liquid wax for appliances 6 Condenser and Evaporator coils should be cleaned at the beginning of each cooling season Use a soft brush or vacuum cleaner to clean them making sure that the Condenser and Evaporator coils are not damaged 7 Do not use abrasive cleaners These items scrach crack and discolor surfaces NOTE To assure continued peak efficiency condenser coils weather side of unit should be checked periodically and cleaned if clogged with soot or dirt from the atmosphere 11 ELECTRICAL REQUIREMENTS e ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three prong grounding plug for protection against possible shock hazards If a two prong wall receptacle is encountered the customer is required to contact a qualified electrician and have the two prong wall receptacle replaced with a properly grounded three prong wall receptacle in accordance with the National Electr
13. ical Code A WARNING To avoid death personal injury or properly damage due to electrical shock this unit must be grounded Do not under any circumstances cut or remove the round grounding prong from the plug Do not use a two prong adapter USE OF EXTENSION CORD Because of potential safety hazards under certain condition we strongly recommend against the use of an extension cord However if you still elect to use an extension cord it is absolutely necessary that it will be a UL listed 3 wire grounding type appliance extension cord rated has a 3 blade grounding plug and a 3 slot receptacle that will plug into the appliance The marked rating of the extension cord should be 125V 13A Min A WARNING To avoid death personal injury or properly damage due to electrical shock do not use an extension cord or pinch the power cord Do not remove the warning tag from the power cord 12 BEFO RE CALLING FOR SERVICE When you find something wrong with your room air conditioner please carefully check the following items If you are unable to find the cause of trouble contact your service dealer Difficulty Possible Cause Suggested Solution Air conditioner does not operate No power to unit Set Fan Control Select to position other than OFF Confirm power cord is plugged in Verify main power switch main circuit breaker or fuse of the unit is good Little or no
14. ieces Window Seal A B 2 pieces JE s Window Seal A 1 piece 2 pieces 2 F 6 ue Md gt Window Seal B 1 piece Window kit Frame Sill Bracket 1 piece Sash Bracket Left side 1 piece 1 piece Window kit Frame Step 2 Prepare Window For Installation EOD WARNING 1 To reduce the risk of electric shock personal injury or death turn the fan control to the OFF position and unplug the unit from the wall outlet before installing or removing this unit 2 The window where the air conditioner is to be installed should have enough strength to bear the weight of the air conditioner Inspect window track sash and sill to be sure they are strong enough to hold an air conditioner 2 Measure width between window frame to be sure instant mount will fit in the window Instant mount models are designed for windows 21 7in 550 to 34 6in 880mm wide Mark the center of window sill with a pencil Insert Screw Type A into the sill bracket Attach Sill bracket to window sill using Screws Type B The outside edge of window bracket should be center line 6 Place the carpenter s level on the sill and the outdoor end of Sill Bracket Adjust Screw A so that Sill Bracket have a slight tilt by using carpenter s level meter about 1 59 AC 0 28 v 0 39 v 7 101g CENTER CARPENTER S LEVEL o ue e o 4 8 INNER WINDOW
15. it is cleaned set the Selector Switch at off position And then unplug the power plug 11 Never store gasoline or other flammable liquid near the air conditioner It is very dangerous 12 Do not force the controls on the front panel too much It can cause damage the controls and the unit 13 Set a comfortable temperature Very low temperature setting considerably increase power consumption 14 Be careful to keep room temperature comfortable Avoid continuous direct air flow on you or a sick person while sleeping 15 Do not remove the plug by pulling the power cord Damage to the cord and may cause shock hazard TABLE OF CONTENTS 1 GENERAL SPECIFICATIONS cere tee re eet ee ede s ER EE 2 2 INSTALLATION 65 3 7 WINDOW REQUIREMENTS BASIC TOOLS NEEDED SAFETY INSTRUCTIONS STEP1 PREPARE COMPONENTS FOR INSTALLATION STEP2 PREPARE WINDOW FOR INSTALLATION STEP3 PLACING UNIT IN WINDOW STEP4 INSTALL SASH BRACKET STEP5 SECURE WINDOW SHUTTER STEP6 RECHECK INSTALLATION STEP7 RECHECK THE ENTIRE INSTALLATION 3 NAMES OF MAJOR COMPONENTS 8 4 OPERATION INSTRUCTIONS IM Hmmm 9 FAN amp COOLING CONTROL TEMPERATURE CONTROL 5 GENERAL INFORMATION ie n patna Ce ee erexit erga c teen ro Pur ea vedas 10 CHANGING
16. ob Study the illustrations in these instructions to become familiar with important details of the installation process Read the Use amp Care manual to become familiar with the operation of your room air conditioner Te A IMPORTANT It is important both for your personal safety and to avoid possible damage to your home that you observe the safety instructions that are given following After installing the unit re read these instructions to make sure you have completed each step and all parts are fastened in place for a secure installation For best results perform the installation procedure in the order given Doing so will minimize the time required to install the unit e BASIC TOOLS NEEDED e Standard screwdriver Phillips screwdriver Sharp knife Carpenter s level 1 4 hex driver Tape measure Electric drill 1 8 drill bit SAFETY INSTRUCTIONS The receptacle should be an individual branch circuit used only for this air conditioner Be sure the electrical service is adequate for the model air conditioner you have chosen The complete electrical rating of your air conditioner is stated on the name plate located at the unit s side Be sure the plug receptacle is close enough for the power cord to reach it WARNING An extension cord must not be used with your air conditioner To minimize shock and fire hazards proper grounding is important For your s
Download Pdf Manuals
Related Search