Eureka Whirlwind LiteSpeed 5843 Upright Vacuum
Contents
1. Clean or replace the filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the airflow through the filter s Be sure the dust cup is properly seated into the cleaner body Page 10 Empty dust cup Page 10 Be sure hose adapter is secure on back of cleaner Page 15 Remove any blockages from the hose that restrict the airflow Page 15 Check base hose and long hose Page 15 Replace a broken cut loose or out of shape belt Clean hair and thread from bristles and end cap area Replace brush roll if bristles are worn Be sure hose adapter is secure Page 15 Clean or replace the filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the airflow through the filters Remove any clogs from the hose that restrict the airflow Check base hose and long hose Page 15 Empty dust cup Headlight not working Light Bulb Replace light bulb Page 14 Noise from the brush roll area Cleaner is hard to push Cleaner height knob will not turn Dust cup will not go into cleaner Properly Hood will not come off VJ Brush Roll v Belt VJ Cleaner Height Setting VJ Belt V Cleaner Height Setting A Dust Cup Lid Assembled WA Cleaner Height Setting V Screws Missing p2. Upright Vacuum Cleaner an Owner s Guide 5740 5799 Series 6 7 5840 5898 Series 8 9 10 LE 12 13 14 15 Do not return this product to the store For assembly problems or questions contact Eureka s 16 Customer Service Division toll free at 1 800 282 2886 8 a m to 7 30 p m CST M F 10 00 17 a m to 6 30 p m CST Saturday 18 For replacement of broken or missing items to be shipped direct to you call 19 1 800 438 7352 8 a m to 4 45 p m CST M F En Mexico llame al 5670 6169 EUREKA IMPORTANT INFORMATION QUICK REFERENCE HOWTO ASSEMBLE HOWTO USE ROUTINE MAINTENANCE Dust Cup Dust Cup Filter Side Door Filters PERIODIC MAINTENANCE Brush Roll Brush Roll Belt Light Bulb PROBLEM SOLVING Clear Hose Guide WARRANTY CUSTOMER ORDER FORM WWW eureka com NOLLVWHOHNI LNYLHOdHII IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Do not leave vacuum cleaner when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments
3. Do not use with damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center before using Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Do not use extension cords or outlets with inadequate current carrying capacity Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow This vacuum cleaner creates suction and contains a revolving brush roll Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not place cleaner on furniture or stairs as the brush roll may cause damage Place cleaner on floor with the handle in storage position while using attachments Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without the dust cup or filter s in place Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt Use extra care when cleaning on stairs Do not use to pick up flammabl
4. aner on furniture or steps as the brush Wand 2 roll may cause damage Place cleaner on floor with the handle in storage position Hose S or 1 To use accessories remove hose from rear of cleaner by lifting up and twisting Dusting Upholstery Brush is for furniture blinds books 2 Place desired accessory onto end of hose or wand i lamp shades shelves curtains draperies cushions and fabrics Crevice Wand cleans corners stairs baseboards and between cushions Nested extension wands to add reach 1 3 Grasp both wands near ridges Er ds qp ou Pull apart glo c p 9L e Turn ridge end to center e Push wands together ISN OLMOH The instructions in this booklet serve as a guide to routine maintenance To avoid unnecessary service calls checkthe dust cup filters belt and brush roll often We suggest emptying the dust cup after every use NOTE When vacuuming carpet fresheners or cleaners powder plaster dust or similar fine substances the dust cup and filters will require more frequent maintenance NOTE Turn off the switch and unplug the electrical cord before changing the filter Never operate the vacuum cleaner without the dust cup or filter assembly in place Emptying the Dust Cup Remove dust cup by pulling latch upward and 2 Grasp dust cup lid and twist counterclock pivoting dust cup out and away from cleaner wise to rem
5. arranty Does Not Cover e Parts of the cleaner that require replacement under normal use such as disposable dust bags filters fans drive belts light bulbs and brush roll bristles Damages or malfunctions caused by negligence abuse or use not in accordance with the Owner s Guide Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts What The Eureka Company Will Do The Eureka Company will at its option repair or replace a defective cleaner or cleaner part that is covered by this warranty As a matter of warranty policy the Eureka Company will not refund the consumer s purchase price Warranty Registration Please fill out and return the warranty registration card accompanying your cleaner Obtaining Warranty Service To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station You will find the nearest location in the Yellow Pages under Vacuum Cleaners Service and Repair Be certain that the Warranty Station is Eureka Authorized For the location of the nearest Eureka Authorized Warranty Station or for service information telephone toll free USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to The Eureka Company Service Division 807 North Main Street Bloomington Illinois 61701 USA In Canada write to The Eureka Company 866 Langs Drive Cambri
6. arts Remove hood and clean debris or items from the brush roll area Replace a broken cut loose or out of shape belt Page 13 Put handle in operating position Tilt the cleaner back to raise the front wheels off floor Then turn the knob to a higher setting Replace a broken cut loose or out of shape belt Page 13 Hint Put handle in operating position Tilt the cleaner back to raise the front wheels off floor Then turn the knob Filter has to be installed in dust cup or dust cup will not go into cleaner Hood cannot be removed from cleaner unless the cleaner height setting is in the lowest or highest position All three screws must be removed from the top of the hood Page 13 Call 1 800 438 7352 between 8 00 a m and 4 45 p m central standard time Monday through Friday Know the model and serial numbers when you call 9pin5 ONIAIOS WJTdOYd Call 1 800 282 2886 between 8 a m to 7 30 p m CST M F 10 00 a m to 6 30 p m CST Saturday Know the model and serial numbers when you call 17 THE EUREKA LIMITED WARRANTY What This Warranty Covers Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of one year The warranty is granted only to the original purchaser and members of his or her immediate household The warranty is subject to the following provisions What This W
7. dge Ontario N3H 2N7 If it is necessary to ship the cleaner outside your community to obtain warranty repair you must pay the shipping charges to the Eureka Authorized Warranty Station Return shipping charges will be paid by the Warranty Station When returning parts for repair please include the model type and serial number from the data plate on the cleaner Further Limitations and Exclusions Any warranty that may be implied in connection with your purchase or use of the cleaner including any warranty of Merchantability or any warranty for Fitness For A Particular Purpose is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Your relief for the breach of this warranty is limited to the relief expressly provided above In no event shall Eureka be liable for any consequential or incidental damages you may incur in connection with your purchase or use of the cleaner Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights You may also have other rights which vary by state GENUINE EUREKA PRODUCT Questions amp Answers about Genuine Eureka Products Q Why should I use only Genuine Eureka paper bags belts and parts in my Eureka vacuum cleaner A Using Genuine Eureka Products which are mad
8. e into slots Rotate filter toward cleaner press firmly against cleaner to latch Make sure True HEPA cartridge latch is secured on both sides 2 Replace filter door by placing tabs of door into slots on cleaner Rotate door up and against cleaner until it locks into place NOTE To have the benefit of a sealed True HEPA system you must use one of the True HEPA cartridge filter systems Use GENUINE EUREKA replacement True HEPA filter HF5 Pre Motor Filter Models equipped with Filter Pads Check the filter pad each time the dust cup is emptied Replace twice a year or as needed SHO 400q PIS 32NVN3LNIVIW 3NLLOOS Ii Du PER Filter Pad 1 5 EUM VIL ES n E N ES I EZ Se Filter LNI Door I G Latch LG To remove Filter Pad from filter door 1 Push down on filter door latch and pull door away from cleaner 2 Lift filter pad up and out of filter door Dispose of old filter pad To replace Filter Pad into filter door 1 Place new filter pad in filter door 2 Replace filter door by placing tabs of door into slots on cleaner Rotate door up and against cleaner until it locks into place Use GENUINE EUREKA replacement HEPA filter HF6 13 Brush Roll The brush roll turns as it sweeps and combs the carpet nap Remove hair and threads from the brush roll so it continues brushing the carpet To maintain the most efficient cleaning the bristles must touch the carpet To test the b
9. e or combustible liquids such as gasoline or use in areas where they may be present Store your cleaner indoors in a cool dry area Keep your work area well lighted Unplug electrical appliances before vacuuming them Unplug before connecting turbo nozzle model 28 SAVE THESE INSTRUCTIONS Lors de l utilisation d un appareil lectrique quelques pr cautions l mentaires doivent tre observ es incluant les suivantes Pour r duire le risque de feu de choc lectrique ou de blessure CONSEILS DE S CURIT LISEZ TOUTES LES INSTRUCTIONS AVANT D UTILISER VOTRE ASPIRATEUR AVERTISSEMENT Ne pas utiliser l ext rieur ou sur des surfaces mouill es Fermez le commutateur et d branchez l appareil lorsque vous ne l utilisez pas ou avant le nettoyage ou l entretien Ne permettez pas qu il soit utilis comme jouet Une attention particuli re est n cessaire lorsque utilis par ou pr s d un enfant ALTNDAS 3d STI3SNOO 4 Suivez les recommandations d utilisation de ce manuel Utilisez uniquement les accessoires recommand s par le fabriquant Ne pas utiliser si le cordon ou la fiche sont endommag s Si l aspirateur ne fonctionne pas comme il le devrait s il a t chapp S il est endommag s il a t laiss l ext rieur ou chapp dans l eau retournez le un centre de service avant d utiliser Ne pas le tirer ou le transporter par le cordon ne pas utiliser le cordon en guise de poign e Ne pas fermer u
10. e source of overheating such as a full dust cup a blocked hose or clogged filter If these conditions are found fix them and wait at least 30 minutes before attempting to use the cleaner After the 30 minute period plug the cleaner back in and push the on off switch on I If the cleaner still does not run then take it to a Eureka Authorized Service Center for repair Questions Do Not Return To Store Call 1 800 282 2886 8 a m to 7 30 p m CST M F 10 00 a m to 6 30 p m Saturday Accessory Items in This Carton 1 Dusting Upholstery Brush 2 screws required to attach handle located in poly bag NOLLVW8ONI LNYLHOdHII Nested extension wands to add reach AL 0 gt 1 extra belt located Grasp both wands near ridges LIL 2 Coo e in poly bag e Pull apart o 1 vacuum cleaner Turn ridge end to center Push wands together handle Thank you for selecting a Eureka cleaner Don t Forget to Use Genuine Eureka Belts Caution Damages caused by the use of non genuine Eureka parts are not covered by the Eureka Limited Warranty 3oN3u3339 XIND Cord Retainer To use push electrical cord down into cord retainer 2 ON OFF Switch International symbol I means On International symbol O means Off 3 Dust Cup Latch Pull up on latch to remove dust cup giving access to the dust cup filter and motor filter Filter Door Latch Push down on latch and pivot out for acces
11. e to our exacting specifications and engineered with emphasis on quality performance and customer satisfaction ensures the long life and cleaning efficiency of your vacuum cleaner Overall this saves you money and helps to keep your home clean How can I be sure I am using only genuine Eureka products in my vacuum cleaner Typically packaged products and paper bags can be identified by a Genuine Eureka Product symbol see illustration above For further identification assistance you may call our toll free number 1 800 282 2886 for the location of a nearby Eureka Authorized Warranty Station Are there any differences between made to fit or imitation and Genuine Eureka paper bags belts and parts Yes there are some very important differences in materials quality and reliability Many customers have mistakenly purchased imitation paper bags and parts while thinking they purchased genuine Unfortunately many of these customers discovered the differences after they experienced related difficulties For Genuine Eureka Value Accept No Imitations THE EUREKA COMPANY Household Warranty Bloomington Illinois 61701 abs 190 18 ALNVYY YM CONTACT FRAN DAVIS EXT 5481 FOR CURRENT CUSTOMER ORDER FORM 2002 White Consolidated Ltd Part No 71496B 11 02 Printed in U S A
12. ep 5 If blockage is found clear and continue to step 11 00O Lower Hose Adapter Base Hose Locate lower hose adapter on the back of the cleaner Remove lower hose adapter from rear of cleaner by lifting up and twisting Check for blockages in the hose and base hose Flexing the hose may help loosen any blockage If no blockage is found continue to step 8 If blockage is found clear and continue to step 11 Remove hood from cleaner and check for a blockage in the brush roll area Make sure the hose inlet is clear After the blockage is found and cleared replace the hood on the cleaner Place lower hose adapter back into the base hose Install the upper hose adapter onto the back of the cleaner line it up with the cleaner opening and push it against the cleaner until both tabs lock into place NOTE Turn off the switch and unplug the electrical cord before servicing CAUSE Electric Plug PROBLEM Motor will not start SOLUTION Push plug securely into outlet Try another outlet Check circuit breaker Does not clean the carpet or floor No suction at the end of hose Vj Filters W Dust Cup V Hose V Belt Brush Roll V Hose Adapter V Filters VJ Hose Vj Dust Cup
13. er using a mild detergent Do not submerge dust cup lid wipe only with a damp cloth a When all parts are completely dry replace filter in dust cup and replace lid Lift filter up and out of dust cup with a twisting motion Clean or replace with a new filter NOTE These parts are not dishwasher safe NOTE Your dust cup filter may need to be replaced if cleaning it does not restore cleaning performance Use GENUINE EUREKA replacement filter Style DCF3 12 Pre Motor Filter Check the pre motor filter each time the dust cup is emptied Clean or replace as needed To Clean Pre Motor Filter 1 Remove filter centered in the bottom of the dust cup compartment 2 Shake filter to remove excess dust If necessary the filter can be cleaned by vacuuming with another cleaner or washing with mild detergent 3 Reinstall filter after completely dry Use GENUINE EUREKA replacement pre motor filter Part No 71480 Models equipped with Cartridge Filter only cartridge style filters can be used with these models Check the True HEPA filter each time dust cup is emptied Replace twice a year or as needed True HEPA Cartridge I aS y Filter Door Latch To remove True HEPA cartridge filter 1 Push down on filter door latch and pull door away from cleaner 2 Push down on HEPA cartridge latch and remove filter To replace True HEPA cartridge filter 1 Place bottom tabs of filter cartridg
14. ne porte sur le cordon ou tirer le cordon sur des coins ou bordures pointus Ne pas circuler sur le cordon avec l aspirateur Tenir le cordon distance des surfaces chauffantes Ne pas utiliser des rallonges ou des prises qui n ont pas de capacit suffisante pour transporter le courant Fermer tous les contr les avant de d brancher Ne pas d brancher en tirant sur le cordon Pour d brancher tenez la fiche et non le cordon Ne pas manipuler la fiche ou l aspirateur avec les mains mouill es Ne pas rien ins rer dans les ouvertures Ne pas utiliser si des ouvertures sont bloqu es assurez vous qu elles soient d gag es de poussi re mousse cheveux ou toute autre chose qui pourrait r duire le passage de l air Cet aspirateur cr e de la succion et contient un rouleau brosse tournant Tenir les parties mobiles et les ouvertures loin des cheveux du linge des doigts et de toute partie du corps Ne pas mettre l aspirateur sur les meubles ou sur les escaliers car le rouleau brosse peut faire des dommages Placer l aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage Ne pas ramasser des objets qui br lent ou fument comme les cigarettes allumettes ou cendres chaudes N utilisez pas sans le coupe de poussi re de ou filtre s en place Les poulies du courroie peuvent devenir chaudes pendant l utilisation normale Pour pr venir des br lures vitez de touch la poulie du courroie lo
15. ove dn53sng 12NVNALNIVN 3NLLOOH 3 Lift filter up and out of dust cup with a twisting 2 Dump debris in a waste container motion Reinstalling the Dust Cup Replace filter onto center tube in dust cup applying gentle pressure Line up tabs on dust cup with openings on lid Tab rotate lid clockwise while applying pressure to secure The lock symbol 4 on lid will be LED centered over dust cup handle when properly assembled G To replace dust cup position dust cup with handle facing inside the dust cup compartment place bottom of dust cup in bottom of compartment and rotate upward pushing dust cup against cleaner until it locks into place 11 Instructions to Clean or Change Dust Cup Filter Style DCF3 Check and clean the filter frequently to maintain good performance Remove dust cup by pulling latch upward and pivoting dust cup out and away from cleaner To clean the Filter Dust Cup and Dust Cup Lid To remove debris tap filter against waste container and or brush with dusting brush accessory tool You may also vacuum the filter using a different cleaner Grasp dust cup lid and ne ot twist counterclockwise to DT 2 If filter needs further cleaning wash in warm remove UD water using a mild detergent To clean between filter pleats fan open under Joy dn 3snq 39NVN3LNIVW 3NLLOOH running water 3 If dust cup needs cleaning wash in warm wat
16. pair Call 1 800 282 2886 for the nearest Eureka Authorized Service Center to you CAUTION Assemble the cleaner before using CAUTION Moving parts make sure on off switch is in off 0 position before plugging in NOTE Features may vary by model yet all parts assemble the same Attach Handle Attach Hose CAUTION Do not catch cord under handle Upper Hose Retainer Groove Hose Lower Hose Retainer T14N1SSV OLMOH From rear of cleaner align handle with groove and slide 3 Pick up hose and lay across upper hose retainer onto cleaner If necessary use thumb and finger pressure to slide handle into position a Push the end of the hose in the lower hose retainer to secure 2 Attach handle with the two 1 inch screws provided in the assembly packet Use a Phillips head screwdriver NOTE Hand tighten with screwdriver to be sure both Screws are firmly seated Store Hose and Accessories Dusting Brush Store Electrical Cord 8 Cord Retainer 6 Cord Hook 6 Un po i i Ej A L 2 T ua FN aum b le Us Plu EI b Plug yO INA 6 Cord Hook 319N1SSV OLMOH You will find your cord retainer on the handle above the upper cord hook Firmly push the electrical cord down into the cord retainer This will place the cord out of the way the next time you vacuum Next wind
17. right side of brush roll to stretch belt Secure right end cap into base y IMPORTANT 9 Rotate brush roll by hand two full rotations to properly position belt 10 Place hood back on cleaner Make sure hood front is behind furniture guard Replace three screws 11 Tighten screws Use GENUINE EUREKA replacement belt Style U Look for the GENUINE EUREKA product symbol How To Change Light Bulb only for models with a headlight NOTE Turn off the power switch and disconnect the electrical cord before changing light bulb a Lower handle Remove the screw from lens cover 2 Pull lens cover from cleaner G Pull old light bulb out of socket a Push new light bulb into socket 8 Replace lens cover 6 Secure with screw Use GENUINE EUREKA replacement light bulb Part No 57940 2 qing auri 15 To Clear Blockages in Hose NOTE Turn off the switch and unplug the electrical cord 9S0H ONIAIOS N1140d OO before clearing hose Adapter Locate upper hose adapter on the back of the cleaner Remove nested wands from back of cleaner for easy access to hose adapter tabs Press hose adapter tabs together and pull hose adapter away from cleaner The hose adapter will unscrew off hose for easy access to debris if necessary a Check for blockages at cleaner opening and in hose If no blockage is found continue to st
18. ristle length hold a ruler against the underneath side of the cleaner If the bristles no longer touch the ruler replace the brush roll Brush Roll Belt Style U The brush roll belt turns the brush roll to agitate sweep and comb the carpet nap Check the belt regularly to be sure it is in good condition Replace the belt if it stretches cracks or loses tension Cut away any hair or threads wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly How To Replace Brush Roll Belt NOTE Turn off the switch and unplug the electrical cord before replacing belt Belt pulleys can become hot during normal use To prevent injury avoid touching the motor shaft when E changing the belt o g O P zi gt C m os 1 Lower handle to floor to change belt a 2 Remove three screws indicated by screwdrivers in above u illustration Lift hood to remove gt e NOTE The carpet height adjustment has to be in the ca lowest or highest position to remove or reinstall the hood u S a e Motor Shaft w e CRM o 2 1 Belt et dl o v Brush X Roll 3 Lift left end of brush roll 4 Remove and discard belt 14 6 Place belt around brush roll pulley 7 Align left end cap with base Push end cap securely into place 8 Pull
19. rsque vous r parez la courroie Portez une attention particuli re lorsque vous nettoyez les escaliers Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l essence Ne pas utiliser dans les endroits o ces liquides pourraient tre pr sents Entreposez votre aspirateur l int rieur dans un endroit propre et sec Maintenez un bon clairage l endroit o vous travaillez D brancher les appareils lectrique avant de les balayer D brancher l appareil avant de brancher Turbo Nozzle Mod le 28 CONSERVEZ CES INSTRUCTIONS s NOLLVIWYOANI LNYLHOdHII To reduce the risk of electric shock this appliance has a polarized plug one blade wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Afin de r duire le risque de choc lectrique cet appareil est muni d une fiche polaris e une des lames est plus large Cette fiche ne peut tre ins r e dans une prise polaris e que d une seule fa on Si la fiche ne peut tre ins r e dans la prise retourner la fiche Si la fiche ne peut toujours pas tre ins r e dans la prise faire installer une prise ad quate par un lectricien qualifi Ne pas modifier la fiche GENERAL INFORMATION The cleaner is designed to pick up dirt and dust par
20. s to the filter compartment Push up on latch to close door Dust Cup Filter Clean the dust cup filter frequently to maintain good performance 6 Dust Cup The debris from cleaning is collected in the dust CUP 2 Stair Handle To use when cleaning stairs Headlight Handle Release Step on handle release to pull handle back to a comfortable operating position 2 Cleaner Height Setting An adjustment that raises or lowers the cleaner base to match the type of floor surface WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting Helpful Information Listen to your cleaner If you notice a change in the sound of the motor or a change in performance it could simply indicate a common usage or maintenance issue Such as a need to raise or lower the carpet height adjustment possible blockage in hose or brush roll area or a broken or loose brush roll belt These are all easy to fix and the instructions are included in this owner s guide Becoming familiar with the information in this guide will help you to get the best possible performance from your new cleaner for many years to come DANA Ill UN j T Hose Retainers 4 Place hose in retainer
21. s to store hose on unit Electrical Cord Hooks 2 Wrap electrical cord around them to store electrical cord on unit The upper cord hook rotates for quick cord release Nested Wand Storage The crevice wand stores inside the larger wand Carrying Handle Use this handle to carry unit from one place to another Dusting Upholstery Brush Storage Store the dusting brush on back of cleaner NOTE WHEN UNIT IS RUNNING DO NOT ATTEMPT TO REMOVE ANY OBJECT WHICH PREVENTS THE BRUSH ROLL FROM TURNING First turn off unit unplug from the electrical socket then remove object from brush roll area Ex sock rug etc 32N3u333u XIND Thermal Cut Off This cleaner has a special thermostat that protects the cleaner in case of motor overheating If the cleaner suddenly turns off follow this procedure 1 Push rocker switch to off O position 2 Unplug cleaner 3 Check for source of overheating problem i e full dust cup blocked hose or clogged filter 4 If a full dust cup blocked hose or clogged filter is found empty the cup clear the hose or replace or clean the filters 5 Wait atleast 30 minutes before attempting to reuse the cleaner 6 After 30 minute cool down period plug the cleaner in and push the rocker switch to the on I position The cleaner should turn on 7 If the cleaner still does not operate take it to any Eureka Authorized Service Center for re
22. the cord around the two cord hooks on the back side of cleaner Secure the plug to the cord to prevent unwinding ON OFF Switch International symbol I means On International symbol O means Off Cleaner Height Setting An adjustment i that raises or lowers the cleaner base WARNING Avoid injury Keep loose clothing to match the type of floor surface With hair fingers and all other parts of the cleaner cord unplugged set the body away from any moving part adjustment to lowest setting for such as the revolving brush Turn maximum carpet cleaning If the off the switch and unplug the TE l ll Ill Ha cleaner is difficult to push move cleaner before changing the adjustment to next highest setting until cleaner is comfortable to push The brush roll must reach the carpet for effective cleaning For ease in moving the adjustment knob place handle in operating position and tilt cleaner back to remove weight from front wheels Handle Release Step on Store handle release to pull Helpful Information handle back to a Operate comfortable operating F Before cleaning under low position To lower SAT furniture check area first for handle completely to ji objects that might harm the the floor depress a unit or block the vacuum handle release a Clean 95 second time Under Dusting Upholstery NOTE While using accessories do not place Crevice 4 Brush Ly cle
23. ticles Avoid picking up hard or sharp objects with the cleaner to prevent hose clogs Service Information The instructions in this booklet serve as a guide to routine maintenance For additional service information telephone our toll free number for the nearest Eureka Authorized Warranty Station You should know the model type and serial numbers when you call USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to The Eureka Company Service Division 807 North Main Street Bloomington Illinois 61701 USA In Canada write to The Eureka Company 866 Langs Drive Cambridge Ontario N3H 2N7 Refer to The Eureka Limited Warranty for complete service information DO NOT OIL the motor or the brush roll at any time The bearings are permanently lubricated and sealed Rating Plate The model type and serial numbers are indicated on the rating plate located on the back side of the cleaner For prompt and complete service VOLTS AMPS HERTZ information always refer to these numbers when inquiring about service Model amp Type Serial No MODEL TYPE SERIAL NO SERVICE INFORMATION 1 800 282 2886 THE EUREKA COMPANY BLOOMINGTON ILLINOIS 61701 Thermal Cut Off This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating If the cleaner suddenly shuts off push the on off switch off 0 and unplug the cleaner Check the cleaner for a possibl
Download Pdf Manuals
Related Search