PPI PC2400 Car Audio Amplifier
Contents
1. This will bypass the amplifier s on board QBASS control 2 COOLING VENTS see page 13 3 POWER GROUND POWERLOCK After you have securely connected your power and ground wires plug in the Power Ground POWERLOCK connector here see page 7 4 POWER indicator A green light indicates that the amplifier is on 5 QBASS Level Turn this control clockwise to boost the QBASS PLUS circuit by up to 18dB 6 FORCED AIR INTAKE VENTS see page 13 13311191111 T BACK TO CONTENTS ENDPLATE DIAGRAM 2400 2600 21400 1 FRONT INPUTS Plug in the RCA leads from your head unit here see page 11 2 GAIN Use this control to match the output level of the head unit to the amplifier see page 12 3 HP LP switch This switch is used to select whether the amplifier will provide a high pass switch in or low pass switch out signal to the speakers see page 12 4 QBASS 1 Use this switch with the QBASS 2 to program the QBASS PLUS circuit see page 2 5 QBASS2 Use this switch with the QBASS 1 to program the QBASS PLUS circuit see page 2 6 FORCED AIR EXHAUST VENTS see page 13 7 SPEAKER REMOTE CONNECTOR After connecting remote and speaker wires plug in the PowerLock connector here see page 10 XOVER ON OFF 8 12dB For use with high level inputs 4V up to 12V Push this switch in to attenuate the input by 1288 see page 11 9 XOVER ON OFF switch Push this switch in to acti2. You will need to install an in line fuse or circuit breaker in the power wire within 18 of the battery This fuse or circuit breaker is to protect your vehicle from fire in case the power wire shorts to the vehicle body If you are only using one amplifier use the fuse rating indicated in this chart If you are using more than one amplifier add up the fuse ratings for all the amplifiers This sum 15 the rating for your fuse or circuit breaker You may also want to add a power distribution block near your amplifiers to keep the wiring tidy BACK TO CONTENTS The following is a basic formula to be used as guide to determine current draw A 50 amplifier efficiency rating is used as an average Your new POWERCLASS amplifier is more efficient other amplifiers will probably be less This formula is to be used as a guideline Using wire of a larger gauge can only improve the current transfer of your system Do not use smaller gauge wire Total RMS output x 2 Total Input Wattage Total Input Wattage Current Draw in Amps Supply Voltage Example A POWERCLASS 2600 amplifier has two channels at 150 watts per channel RMS rating into 4 Ohms 150 x 2 300 You would use the formula in the following way 300W x 2 600W 600W 50A Total current draw 12V If the same amplifier is driven into a 2 Ohm stereo or 4 Ohm mono load double it s 4 Ohm RMS rating All POWERCLASS amplifiers will effectively double their power at this l
3. crossover is adjustable from 20 E 92r He to 5 kHz Please refer to the a 2 endplate diagram and detent chart 35 Hz provided for frequency adjustments d The XOVER FREQ control has udis detents or clicks as you rotate it 25 de Each click counted from the full hiz Sdn 2 counterclockwise position 100 Hz d ific f 114 Hz corresponds to a specific frequency 134 Hz This will add more accurate tuning e i 260 Hz to your system 420 Hz Also refer to your owner s manual je D RP z for installation instructions 496 Hz As always PrecisionPower will 228 Hz 864 Hz continue to improve the products 1008 Hz 1200 Hz and services we have to offer you BS HE Thank you for choosing 1032 se ini 2 PrecisionPower 4512 Hz 4944 Hz 5000 Hz New variable crossover 13311111111 jl 1111 H MERLO 9 BACK TO CONTENTS WARRANTY ot Three Year Limited U S A Warranty This warranty gives you specific legal rights and you may also have other rights which vary from state to state PrecisionPower warrants its products to be free from defects in materials and workmanship under normal use and service for a period of three 3 years from the date of original purchase when the unit is installed by an Authorized Dealer Non Authorized Dealer installed products carry a one 1year parts and ninety 90 days labor limited warranty The extent and conditions of Limited Warranty are as follows 1 Authorized
4. operation of your PrecisionPower product should occur contact your Authorized Dealer for assistance with the return and factory repair of your PrecisionPower product If an Authorized Dealer is not available return the unit including your name telephone number return address a copy of your sales receipt and a description of the problem to PrecisionPower Inc Service Department 4829 S 38th Street Phoenix AZ 85040 2964 TO RETURN PRECISIONPOWER PRODUCTS OUT OF WARRANTY Return the unit postage prepaid in the original protective carton Please include a description of the problem and if desired a request for an estimate of repair costs Unless a request for an estimate is included the unit will be repaired as necessary Please contact PrecisionPower Customer Service at 1 800 62 POWER for questions concerning out of warranty repair charges Repaired unit will be returned with an itemized statement C O D BACK TO CONTENTS
5. 2 volts RMS Input Impedance 10 k Ohms Load Impedance stereo 2 8 Ohms Load Impedance bridged 4 8 Ohms Supply Voltage 11 15 volts Damping Factor 2500 Slew Rate gt 50 V uS QBASS PLUS Up To 18dB Boost Frequency Centers 30Hz 36Hz 44Hz and 60Hz Idle Current PC2400 1 5 Amps PC2600 2 Amps PC21400 3 Amps Crossover Two Way 24dB Octave Linkwitz Riley Crossover Frequency 90Hz Dimensions PC2400 100 WRMS x 2 4Q per channel Length 15 75 200 WRMS x 2 20 per channel Height 2 25 di 400 WRMS x 1 40 bridged Width 8 9 PC2600 150 WRMS x 2 4Q per channel Length 17 75 300 WRMS x 2 2Q per channel Height 2 25 600 WRMS x 1 40 bridged Width 8 9 PC21400 350 WRMS x 2 4Q per channel Length 25 25 700 WRMS x 2 20 per channel Height 2 25 1400 WRMS x 1 40 bridged Width 8 9 1 BACK TO CONTENTS QBASS PLUS QBASS PLUS On PC2400 PC2600 and PC21400 amplifiers we ve taken bass control to a higher level with QBASS PLUS The two QBASS switches labeled 1 and 2 on the front end of the amplifier allow you to select one of four frequency centers 30Hz 36Hz 44Hz and 60Hz The Q SELECT switch determines the width of boosted frequencies A Q of 2 switch out will give you a wide boost while a Q of 4 will boost a narrow range of frequencies See chart below On the rear end panel you will find the QBASS level control and the plug in for an optional QBASS REMOTE dash moun
6. Dealer Installed Products PrecisionPower will either repair or replace at no charge to the original purchaser any unit which PrecisionPower s examination discloses to be defective and under warranty provided the defect occurs within three 3 years from the date of original purchase when the unit is installed by an Authorized Dealer and the product is returned immedi ately to PrecisionPower This warranty is not transferable 2 Non Authorized Dealer Installed Products PrecisionPower will either repair or replace at no charge to the original purchaser any unit which PrecisionPower s examination discloses to be defective and under warranty provided the defect occurs within ninety 90 days from the date of purchase and the product is returned immediately to PrecisionPower Warranty claims beyond ninety 90 days for Non Authorized Dealer Installed Products will be for parts only and will extend for one 1 year from the date of purchase This warranty is not transferable 3 The date of purchase and proof of Authorized Dealer Installation of a PrecisionPower product must be established by an original sales receipt which must accompany the article being re turned for warranty work 4 This warranty shall NOT apply to any PrecisionPower product found to have the original fac tory serial number removed or defaced All products received by PrecisionPower for in war ranty or out of warranty repair with their original serial numbers removed or
7. POWERCLASS PC2400 PC2600 PC21400 OWNER S MANUAL CONTENTS click on a topic to a _ CONGRATULATIONS INPUTS _ FEATURES SPECIFICATIONS _ CROSSOVER GAIN CONTROL MATES PLUS _ THERMAL MANAGEMENT _ INSTALLATION TROUBLE SHOOTING _ WIRING _ SYSTEM DIAGRAM ONE _ WIRING continued _ SYSTEM DIAGRAM TWO POWER GROUND _ SYSTEM DIAGRAM THREE POWER GROUND and REMOTE _ SYSTEM DIAGRAM FOUR REAR ENDPLATE DIAGRAM BLOCK DIAGRAM FRONT ENDPLATE DIAGRAM _ ADDENDUM _ WARRANTY lili gl qp ls mls ql gl gl SPEAKER WIRING yl yl ll ol ml gl ml mpl mln for choosing PrecisionPower audio epuipment At PrecisionPower we proudly design engineer and manufacture audio products at our facility in Phoenix Arizona Our award winning engineering team utilizes innovative technology to consistently deliver Absolutely State of the Art performance sound quality reliability and value This PrecisionPower product reflects our commitment to offer you unparalleled versatility and quality for years of dependable service and listening enjoyment Service Do not attempt to service PrecisionPower products yourself Performing exploratory surgery on your audio equipment yourself will void the warranty Many parts of your PrecisionPower gear are custom built to our specifications Our factory parts are not made available to anyone else nor are they for sale Our goal is to make sure that your PrecisionPower product
8. amplifier input gain controls to just above minimum sensitivity fully counterclockwise ni 2 Using the cleanest source CD with music playing turn up the head unit until you can hear distortion Now turn it down a bit until you cannot hear the distortion 3 Increase the Amplifier gain clockwise until the onset of audible distortion Then decrease the gain to the point just before the distortion starts This setting minimizes background noise and prevents overload 4 Repeat step 3 for any remaining amplifiers in the system BACK TO CONTENTS THERMAL MANAGEMENT O Heatsink Cooling unique heatsink on 7 your POWERCLASS amplifier has been designed with fins on the inside of the aluminum mass This allows for the transfer of heat from the circuitry to the heatsink fins and out through the vents in the endplates Be sure you have ample space around the amplifier for cooling at least 2 on all sides Forced Air Thermal Management To manage the additional heat associated with higher output capability a thermally controlled fan has been designed into the PC2600 and PC21400 When the heatsink temperature reaches a pre determined value the fan is activated and cool air is drawn in through the lower intake vents on the endplate This cool air flows below the circuit board through the fan and across the internal fins cooling the heatsink The warm air is then forced out through the upper endplate exhaust
9. any special cables see diagram below This type of input works with any conventional RCA cable My my yl music noise 9 signal and ground music noise music and noise music noise noise noise cancels music NO noise BACK TO CONTENTS CROSSOVER and GAIN CONTROL Crossover Your new POWERCLASS amplifier has a 90Hz fourth order Linkwitz Riley type 24dB per octave phase correlated crossover built in to provide system flexibility without the added expense and installation of an outboard crossover The speaker outputs of your amplifier are high pass or low pass according to the HP LP switch on the front endplate You would choose low pass switch out to use this amp for subwoofers or choose high pass switch in to use this amp for full range speakers The RCA outputs are controlled by the same HP LP switch but are always the inverse of the speaker output crossover If the HP LP switch is out LP the RCA outputs will be high pass and if the HP LP switch is in HP the RCA outputs will be low pass In addition the speaker outputs can be all pass no crossover by setting the XOVER ON OFF switch to the off out position ly NOTE The RCA outputs are always crossed over The System Diagrams beginning on page 14 show several ways to use the internal crossover in your system Adjusting The Amplifier Input Gain 1 Adjust all
10. by using the left channel positive wire as the positive speaker wire and the right channel negative wire as the negative speaker wire NOTE It is important that a minimum 4 ohm impedance is observed If the impedance drops below 4 ohms while the amplifier is wired in the bridged configuration the amplifier s protection circuitry AM IV may engage 10 BACK TO CONTENTS in eS ti There are two sets of RCA jacks on the front end of your amplifier The RCA cables from your head unit go in the set labeled INPUTS If your head unit doesn t have RCA outputs don t worry Simply add a set of RCA plugs available at your dealer to your front or rear set of speaker leads see drawing below plug them into the input jacks and push in the 12dB input attenuation switch SOURCE Headunit eee Positive A d LEFT input Positive cin Ro E RIGHT input Negative D WARNING f you are using a source unit with bridged high powered or floating ground speaker outputs a suitable high to low level adapter must be used If you are unsure about your head unit see your local PrecisionPower dealer or call 1 800 62Power Balanced Differential Inputs This circuitry reduces noise radiated into your signal cables by up to 4088 This is equivalent to a noise reduction of approximately one hundred times what the noise level would be without this circuitry It provides all the benefits of a true balanced line without the need of
11. defaced will NOT be repaired and will be returned to sender freight collect Refer to original packaging for the serial number of your component speakers 5 The provisions of this warranty shall not apply to any PrecisionPower product used for a purpose for which it is not designed which has been repaired or altered in any way or which has een connected installed or adjusted other than in accordance with the instructions furnished in PrecisionPower s owner s manual Nor shall this warranty apply to any part which has been subject to misuse neglect or accident 6 PrecisionPower does not authorize any other persons to assume any other liability in connec tion with its products THIS WARRANTY IS THE ONLY EXPRESS WARRANTY MADE BY PRECISIONPOWER APPLICABLE TO ITS PRODUCTS ANY IMPLIED WARRANTY OR MER CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO PRECISIONPOWER PRODUCTS IS LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY PRECISIONPOWER SHALL NOT BE LIABLE FOR THE INCIDENTAL CONSEQUENTIAL OR COMMERCIAL DAMAGES RESULTING FROM THE BREACH OF THIS WRITTEN WARRANTY Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you 7 Your product will be serviced on an in warranty basis within the warranty period for the correc tion of warranted defects If improper
12. ff or Low Pass 16 BACK TO CONTENTS SYSTEM DIAGRAM Source Unit PAR 245 Preamp Equalizer Front Output Rear Output PSC 221 Phase Shift Control Passive Passive Tweeter 4 Crossover Crossover Tweeter MidRange n MidRange POWERCLASS Amplifier High Pass at 90 Hz Subwoofer a Subwoofer N POWERCLASS Amplifier Low Pass at 90 Hz 17 BACK TO CONTENTS SYSTEM DIAGRAM Source Unit FRX 456 Crossover PSC 221 Phase Shift Control High Pass Frequencies Tweeter 2 Tweeter POWERCLASS Amplifier Crossover off Y Mid Range Frequencies Mid Range a Mid Range SN POWERCLASS Amplifier amp Crossover off Y Low Pass Frequencies A Subwoofer Subwoofer POWERCLASS Amplifier Crossover off 18 BACK TO CONTENTS BLOCK DIAGRAM le Ez vod lt lt wiSNTd Ssvao lt ejnu lt wJLONWJH 55780 E AAO NO H3AO X 193138 dVdH anepo sseq M0 206 enejo0 gprc SSed 206 Sseg 1288 INPUT ATTENUATION indu vod 19 BACK TO CONTENTS POWERCLASS ADDENDUM DETENT XOVER FREQ Your new POWERCLASS amplifier l 2 Lr 2 may have been updated to include a 3 21 Hz E 4 21 5 Hz variable detented crossover in place 5 22 Hz 6 23 Hz of the Q 4 2 function switch The gt 24 5 Hz r ver is adj le from 20 Hz 8 26 Hz
13. lifier to run warmer 14 BACK TO CONTENTS SYSTEM DIAGRAM Source Unit Passive Passive Tweeter 1 Crossover Crossover b Tweeter MidRange po E D MidRange 5 Sy YA POWERCLASS Amplifier Crossover Off Passive Crossover Subwoofer Mixed Mono Output The ability to run stereo speakers while simultaneously running mono output from the same amplifier is accomplished by running the stereo speakers normally and tapping into the appropriate wires for the mixed mono channel left channel positive for the positive speaker wire and right channel negative for the negative speaker wire Speaker impedance should be no lower than 2 Ohms on the stereo channels and 4 ohms on the mono channel NOTE Passive crossovers must be used for mixed mono operation Choose a low pass crossover around 100Hz for your subwoofer then choose a high pass crossover for your stereo channels The high pass crossover must be at the same or slightly higher frequency than the low pass crossover to maintain the correct impedance See your PrecisionPower dealer or call 1 800 62POWER for more information about passive crossovers BACK TO CONTENTS SYSTEM DIAGRAM HEN NENNEN Source Unit Passive Passive Tweeter 1 Crossover Crossover Tweeter MidRange n MidRange POWERCLASS Amplifier High Pass 90Hz Low Pass Out to Sub Amplifier Subwoofer x s Subwoofer POWERCLASS Amplifier Crossover o
14. nto the wires when you replace the trim For systems over 300 watts add a ground cable from the amp to the battery see page 6 BACK TO CONTENTS POWER GROUND Locate an area near the amplifier s that is metal and clean an area about the size of a quarter to bare metal Inspect the area around and underneath to be sure you won t drill into wires brake or fuel lines etc Drill a pilot hole in the middle of this area Terminate the ground wire with a ring connector and attach itto the bare metal using a 48 sheet metal screw and washer or preferably a bolt nut and a star washer not supplied We suggest crimping and soldering this connection After the connection is complete coat the area on both sides with silicone or some similar material to prevent rust from developing on the bare metal My i If your grand total current draw is over 50 amps or total output power is over 300 watts you should run a ground wire beside your power wire from the battery to the amplifier s in addition to your regular ground wire Keep the ground and power wires as close together as possible and use the same gauge wire for both This will ensure that you have a good ground path and may eliminate such potential problems as engine noise and overheated amplifiers harging System Considerations If your grand total current draw is over 100 amps or total output power is over 600 watts you are probably exceeding the capability
15. oad 300W x 2x 2 1200W 1200W 100A Total current draw 12V If you are using more than one amplifier add up the total current draw for all of them and choose the appropriate gauge based on the grand total Power Wire Calculator Recommended MINIMUM Gauge yi Total Current Draw Length Of Wire To Be Run in Amps Upto4ft 41074 71010 10to 13ft 13to 16ft 16to 19ft 19 to 22ft 2210 281 10 125 150 NOTE The ground wire should be the same gauge as the power wire 4 BACK TO CONTENTS Before beginning disconnect the negative terminal of the battery prior to working on the positive terminal to prevent a short to ground This is important unless you want to spend the rest of your life with a nickname like Sparky or Smokey Reconnect the negative terminal only after all connections have been made Factory Ground wire may need to be replaced if it is frayed or broken Run signal cables RCAs and remote turn on lead down the opposite side of the vehicle of the power wire to avoid radiated noise Avoid sharp edges that could through the insulation Warning y Fuse must be installed within 18 of battery Wl Positive Battery Terminal Fuse must be installed within 18 of battery Drill a hole in the firewall and use a rubber grommet to keep wire from shorting Run the cables under the carpet near the side of the vehicle Be careful not to drill or screw i
16. of your charging system Dimming lights and fluctuating voltage are solid indicators that you need to upgrade your alternator battery or go to multiple batteries or both Keep in mind that your amplifiers simply convert electrical energy to acoustical energy and any electrical deficiency will compromise the performance of your sound system For more information about charging system upgrades see your local authorized PrecisionPower Dealer or call the PrecisionPower technical support office at 1 800 62POWER li i BACK TO CONTENTS POWER GROUND and REMOTE Once you have run both the power and ground wires it s time to connect the cables to the amplifier Cut off excess wire and using wire strippers strip the ends of the power and ground cables approximately 1 4 inch Locate the PowerLock power and ground connector supplied With a small flat bladed screw driver loosen the screws before attempting to insert the cables Insert the wires into the appropriate hole and tighten the screws Once the wires are secure the PowerLock may be plugged into the amplifier The Power Ground PowerLock will accommodate 4 gauge wire for the PC2400 PC2600 and PC21400 Power Ground PowerLock Fastening screws Power wires Connect to Amplifier BACK TO CONTENTS ENDPLATE DIAGRAM 2400 2600 21400 1 QBASS REMOTE plug in Plug in the data cable from the optional QBASS REMOTE dash mount level control here
17. ted level control Adjust the level control clockwise for up to 18dB of boost at your selected frequency and Q li i QBASS Settings 30Hz 36Hz 44Hz 60Hz CAUTION 55 PLUS should only be used in systems with strong subwoofers 18dB is a lot of bass boost and could damage full range speakers Optional QBASS REMOTE This boost control can be mounted in the dash and will supersede the boost control on the endplate Optional expansion module allows one boost control to operate multiple amplifiers Each QPORT has outputs for four amplifiers as well as another QPORT for greater expansion See your Authorized PrecisionPower Dealer for more information 2 BACK TO CONTENTS Tools Parts needed for Installation not supplied Small flat blade screwdriver Phillips Screwdriver 2 or medium sized Wire cutters Wire strippers 4 6 round head screws and 1 8 sheet metal screw or nut bolt and star washer 2 Ring connectors large enough to accommodate your method of grounding In line fuse or circuit breaker see fuse chart below Power and ground wire see Power Wire Calculator on page 3 Speaker wire 16 gauge or larger Grommets sized to work with the power wire you plan to use in your installation Tube of silicone sealant Fuse requirements my yu n i Amplifier Maximum Fuse Rating PC2400 PC2600 PC21400
18. vate the crossover or out for full range speaker outputs see page 12 10 OUTPUTS Left and Right RCA outputs provide high pass or low pass signal to another amplifier see page 12 NOTE RCA outputs are always high pass or low pass 11 Q SELECT 4 2 Push this button in for a Q setting of 4 and out for a setting of 2 see page 2 12 FORCED AIR INTAKE VENTS see page 13 BACK TO CONTENTS SPEAKER WIRING eit Using 16 gauge or larger run the speaker wires from the amplifier location through the vehicle to the speakers Observe the same precautions for routing these wires that you followed for running the power and remote turn on wires Cut off excess and using wire strippers strip 1 4 inch of insulation Locate the speaker remote turn on PowerLock connector Loosen the four outer screws on the underside of the connector Insert the speaker leads into the end Check to be sure you ve maintained proper polarity before securing each wire and plug the PowerLock into the amplifier Speaker PowerLock Connector 3 gt Right Speaker negative Right Speaker positive Remote turn on Left Speaker positive Speaker Remote PowerLock n e O All two channel POWERCLASS amplifiers are capable of being bridged into a 4 ohm mono output without switches or bridging modules This feature permits the creation of a mono channel for a subwoofer or center channel li i Deriving the mono channel is accomplished
19. vents m li i Cool Air Intake BACK TO CONTENTS Warm Air Exhaust TROUBLE SHOOTING et YES NO Check Power and Remote turn on wire for voltage Make sure Ground wire is secure STILL NO SOUND See your Authorized PrecisionPower Dealer or call 1 800 62POWER SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector turning it over and plugging it back in SOUND 15 NOW IN OPPOSITE CHANNEL SAME CHANNEL Reverse RCA inputs Problem is in the speaker or speaker wire of the silent channel M SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL Reverse RCAs at head unit Problem is in the Amplifier See your local Authorized PrecisionPower Dealer or call 1 800 62POWER S SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL Problem is in the head unit Problem is in the RCA cables AMPLIFIER TURNS DOWN Both excessive temperature and low impedance or short circuit conditions will activate the amplifier s AM IV protection circuitry which turns down the amplifier s output When the amplifier cools down or the impedance is corrected the AM IV will restore full power If your amp is turning down check your speakers and wiring for low impedance and short circuits Also ensure that there is nothing blocking the normal convective airflow of the amplifier No obstruction should be within 2 of the amplifier on all sides NOTE Low battery voltage will cause the amp
20. will always sound as good as the day it was purchased Contact your authorized PrecisionPower dealer about obtaining any warranty service through PrecisionPower See Warranty insde back cover y FOR YOUR RECORDS Model Serial Number Purchase Date The extended use of a high powered audio system may result in hearing loss or damage While PrecisionPower systems are capable of Concert Level volumes with incredible accuracy they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians Please observe all local sound ordinances ny jl h BACK TO CONTENTS FEATURES SPECIFICATIONS O Adaptive MOSFET Switching Power Supply Fully Complementary Triple Darlington Output Stage AM IV Protection Circuitry QBASS PLUS Bass Boost QBASS REMOTE Compatible Advanced Buss Technology Forced Air Thermal Management Two Way 24dB Octave Linkwitz Riley 90Hz Crossover Crossover Line Outputs Balanced Differential Input Stage High Voltage Input Capability with Input Attenuation Switch Gold Plated RCA Input and Output Connectors PowerLock Speaker and Power Wire Connectors Mixed Mono Stereo Operation Three Year Warranty when installed by an Authorized PrecisionPower Dealer Completely Designed and Handcrafted in the USA Power Bandwidth 4 5 Hz 100 kHz Total Harmonic Distortion 0 02 lt Input Topology Differential Input Sensitivity 150mv 1
Download Pdf Manuals
Related Search