Home
Whirlpool 98015194 Range User Manual
Contents
1. Reinstall burner tube and bracket assemblies e Lower cooktop Reinstall screws to secure burner tubes to cooktop Reinstall burners burner caps and burner grates Do not reinstall control panel or knobs They will be reinstalled in Step 10 on Page 9 6 Oven burner a Open oven door and remove oven racks oven tray flame spreader and set aside Lift oven burner The orifice spud is behind the oven burner air shutter b Locate Natural gas orifice spud stamped 47 in literature package supplied with range c Use a 3 8 combination wrench and remove the L P gas orifice spud Install the number 47 Natural gas spud Place L P gas oven burner spud in plastic parts bag along with L P gas cooktop burner spuds for future use and keep with literature package d Reinstall the oven burner oven burner orifice behind air shutter Natural gas oven orifice spud stamped with 47 I 7 Turn manual shutoff valve in gas supply line on If Gas and electrical connection Steps 10 16 on Page 6 were not completed complete them now 3 Install control knobs Complete Check operation section Steps 17 22 Page 7 Check for proper flame Natural gas flames do not have yellow tips 9 Close the broiler door Turn oven control knob to OFF 1 0 m Remove control knobs Reinstall the control panel Securely tighten the 4 screws Reinstall the control knobs IMPORTANT If not done in
2. Installation Instructions 30 76 2 cm Freestanding Gas Range with standard clean oven factory set for use with L P gas 4 WARNING 4 Tip Over Hazard A child or adult can tip the range and be killed Connect anti tip bracket to rear range foot Reconnect the anti tip bracket if the range is moved Failure to follow these instructions can result in death or serious burns to children and adults IMPORTANT Read and save these instructions IMPORTANT Installer Leave Installation Instructions with the homeowner Homeowner Keep Installation Instructions for future reference Save Installation Instructions for local electrical inspector s use 98015194 Pages a s S N er 5 69 oo N _ Quick Reference Table of Contents Before you start Product dimensions Cutout dimensions requirements Electrical requirements Gas supply requirements Installation steps Gas conversions Moving the range If range does not operate If you need assistance service Write down the model and serial numbers before installing range Both numbers are listed on the model serial rating plate located on the frame behind the broiler door Model Serial www whirlpool com Part No 98015194 Before you start Your safety and the safety of others are very import
3. Step 8 check the LO flame adjustment See Check operation section Step 19 Page 7 L P gas conversion 1 Check that the manual shutoff valve in the gas supply line has been turned off 2 m Open broiler drawer and remove broiler pan The pressure regulator is located in the back right hand corner of the broiler compartment viewed from inside broiler compartment 3 m Pressure regulator Remove the cap from the pressure regulator Turn the cap over so that LP is visible Replace the cap 4 Remove burner grates burner caps burners and screws Lift cooktop NOTE There is no cooktop support rod Cr cap boa burner screw 5 m Cooktop burners a Check that all control knobs are in the OFF position and remove the knobs b Remove the control panel See Step 17a Page 7 c Lift front of bracket and push tube and bracket assembly back off orifice bracket burner d Locate L P gas orifice spuds for top burners in literature package included with the range Three L P gas spuds are stamped 65 and one 62 Remove Natural gas orifice spuds using a 3 8 combination wrench Install L P gas orifice spuds in locations shown to replace the Natural gas orifice spuds NOTE Depending on model the range cooktop may be equipped with 4 standard burners or 3 standard burners and 1 power burner Spud size location remain the same Place Natural gas orifice
4. WCP Contact local gas supplier if you are not sure about the inlet pressure Line pressure testing above 1 2 psi gauge 3 5 kPa 14 35 6 cm WCP The range and its individual manual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than 1 2 psig 3 5 kPa Line pressure testing at 1 2 psi gauge 3 5 kPa 14 35 6 cm WCP or lower The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of that system at test pressures equal to or less than 1 2 psig 3 5 kPa Now start 4 WARNING Excessive Weight Hazard Use two or more people to move and install range Failure to do so can result in back or other injury 1 Do not use oven door handle to lift or move the range 2 m Remove oven racks and parts package from inside oven Remove shipping materials tape and protective film from range 3 Keep cardboard shipping base under range to prevent damage to floor covering cardboard shipping base 4 WARNING Tip Over Hazard A child or adult can tip the range and be killed Connect anti tip bracket to rear range foot Reconnect the anti tip bracket if the range is moved Failure to follow these instructions can result in death or serious burns to children and adults Contact a qualified floor covering installer f
5. bracket shipped with the range see Page 5 and the anti tip bracket template Electrical requirements 4 amp WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine that the ground path is adequate Do not ground to a gas pipe Check with a qualified electrician if you are not sure range is properly grounded A 120 volt 60 Hz AC only 10 amp fused electrical supply is required A time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided Electronic ignition systems operate within wide voltage limits but proper grounding and polarity are necessary In addition to checking that the outlet is correctly grounded the outlet must be checked by a qualified electrician to see if it is wired with correct polarity IMPORTANT This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized A wiring diagram is included on the back of the range See Cutout dimensions requirements section for recommended location of electrical outlet Recommended ground method For personal
6. safety this range is equipped with a power supply cord having a 3 prong ground plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong ground type outlet grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances If a mating outlet is not available it is the personal responsibility and obligation of the customer to have a properly polarized and grounded 3 prong outlet installed by a qualified electrician 3 prong polarized ground type outlet 3 prong ground Gas supply requirements 4 WARNING Explosion Hazard Use a new AGA or CSA approved gas supply line Install a shutoff valve Securely tighten all gas connections If connected to LP have a qualified person make sure gas pressure does not exceed 14 water column Examples of a qualified person include licensed heating personnel authorized gas company personnel and authorized service personnel Failure to do so can result in death explosion or fire In the State of Massachusetts the following installation instructions apply e Installations and repairs must be performed by a qualified or licensed contractor plumber or gasfitter qualified or licensed by the State of Massachusetts e If using a ball valve it shall be a T handle type e A flexible gas connector when used must not exceed 3 feet Observe all governin
7. the anti tip bracket Use 3 8 drive ratchet and channel lock pliers to adjust leveling legs up or down until range is level Push range back into position Check that rear leveling leg is engaged in anti tip bracket NOTE Oven must be level for satisfactory baking conditions SS LLM LO 4 LLL yp 7 Gas and electrical connection 1 0 m Assemble the flexible connector to the gas supply pipe to the pressure regulator connection fitting using the adapter fittings provided with the flexible connector Use pipe joint compound made for use with L P gas to seal all pipe thread connections regulator connection fitting 4 UH All connections must be wrench tightened i L p 90 elbow __ black iron pressure regulator pipe connection fitting unon oy manual Typical rigid gas i i F shutoff pipe connection jinnie__ es 1 2 to 3 4 Co gas pipe Typical flexible connection pressure regulator connection fitting use pipe joint compound agm adapter flexible connector use pipe joint La compound adapter manual gas shutoff 1 2 to 3 4 valve gas pipe A 1 2 male pipe thread is needed for connection to pressure regulator female pipe threads 1 1 If a flexible appliance connector is used be certain connector is not kinked 1 2 m Check that all control knobs are in the OFF position 1
8. 3 m Check that range regulator shutoff valve is in the on position Open the manual shutoff valve in the gas supply line viewed from inside broiler compartment regulator shutoff valve in on position manual shutoff valve open position to range 1 4 Test all connections by brushing on an approved non corrosive leak detection solution Bubbles will show a leak If a leak appears shut off gas supply valve and tighten connections Then check connections again Clean all leak detection solution from gas connections Close broiler door 1 5 m Place burners burner caps and grates on cooktop 1 6 Plug power supply cord into grounded electrical outlet Check operation Electronic ignition system Cooktop and oven burners use electronic ignitors in place of standing pilots When a cooktop control knob is turned to the LITE position the system creates a spark to light the burner This sparking continues until the control knob is turned to the desired setting When the oven control is turned to the desired setting a hot surface ignitor heats to a bright orange and ignites the gas No sparking occurs The glow bar remains on while the burner operates Check operation of cooktop 1 7 Push in and turn each surface unit control knob to LITE position The flame should light within 4 seconds Turn control knob to HI position after burner lights noisy or blo
9. Batterymarch Park Quincy Massachusetts 02269 CSA International 8501 East Pleasant Valley Road Cleveland Ohio 44131 5575 Flexible metal appliance connector If local codes permit a new CSA design certified 1 2 or 3 4 I D flexible metal appliance connector is recommended for connecting range to the gas supply line A 1 2 male pipe thread nipple is needed for connection to pressure regulator connection fitting Do not kink or damage the flexible metal tubing when moving the range Rigid pipe connection Requires a combination of pipe fittings to obtain an in line connection to the range All strains must be removed from the supply and fuel lines so range will be level and in line Shutoff valve The supply line must be equipped with a manual shutoff valve This valve should be located in the same room as the range and should be ina location that allows ease of opening and closing The valve is for turning on or shutting off gas to the range Do not block access to shutoff valve manual shutoff valve open position to range PE gas supply Pressure regulator The gas pressure regulator supplied with this range must be used The inlet pressure to the regulator should be as follows for proper operation L P GAS Minimum pressure 11 inches 27 9 cm WCP Maximum pressure 14 inches 35 6 cm WCP NATURAL GAS Minimum pressure 5 inches 12 7 cm WCP Maximum pressure 14 inches 35 6 cm
10. ant We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean 4 DANGER You can be killed or seriously injured if you don t immediately follow instructions 4 WARNING You can be killed or seriously injured if you don t follow instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch e Do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or t
11. e anti tip bracket is installed e Look for the anti tip bracket securely attached to floor e Slide range back so rear range foot is under anti tip bracket anti tip bracket range foot 6 Check that range is level 7 Reconnect gas line to range and check for leaks 8 Plug in range or reconnect power 10 For cleaning and maintenance If removing the range is necessary for cleaning or maintenance disconnect the electric supply If electrical supply is inaccessible lift the range slightly at the front and pull the range away from the wall Pull the range out only as far as necessary to disconnect the electrical supply line Remove the range to complete cleaning or maintenance Move range back into operating position Remove drawer Level the range Reconnect the electrical supply Make sure that left rear leveling leg is engaged in the anti tip bracket If range does not operate WA Check that the circuit breaker is not tripped or the house fuse blown S Check that the power supply cord is plugged into the outlet PA Check that gas line is turned on S See Use and Care Guide for troubleshooting list NOTE Refer to Use and Care Guide for operating and cleaning instructions If you need assistance If you have questions about operating cleaning or maintaining your range S Refer to Use and Care Guide L Check your Use and Care Gu
12. e installation of this range must conform with the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Home Installations ANSI NCSBCS A225 1 and Manufactured Home Installations Sites and Communities ANSI NFPA 501A or with local codes When this range is installed in a mobile home it must be secured to the floor during transit Any method of securing the range is adequate as long as it conforms to the standards listed above Copies of the standards listed may be obtained from CSA International 8501 East Pleasant Valley Road Cleveland Ohio 44131 5575 National Fire Protection Association One Batterymarch Park Quincy Massachusetts 02269 Tools and materials needed Follow all factory safety instructions included with your tools e level e 3 8 drive ratchet e 1 2 and 3 8 wrenches e flat blade screwdriver e Phillips screwdriver e hand or electric drill e wood floor 1 8 drill bit concrete ceramic floors 3 16 carbide tipped masonry drill bit Hammer may be needed for anchors e slip joint pliers tape measure or ruler pipe wrench Materials required e gas line shutoff valve e 1 2 male pipe thread nipple for connection to pressure regulator e L P gas resistant pipe joint compound e CSA design c
13. er compartment viewed from inside broiler compartment Do not remove the pressure regulator 3 m Pressure regulator Remove the cap from the pressure regulator Turn the cap over so that N or NAT is visible Replace the cap 4 Remove burner grates burner caps burners and screws Lift cooktop NOTE There is no cooktop support rod burner cap burner 5 m Cooktop burners a Check that all control knobs are in the OFF position and remove the knobs b Remove the control panel See Step 17a Page 7 c Lift front of bracket and push tube and bracket assembly back off orifice bracket burner ee d Locate Natural gas orifice spuds for top burners in literature package included with the range Three Natural gas spuds are stamped 145 and one 52 Remove Natural gas orifice spuds using a 3 8 combination wrench Install Natural gas orifice spuds in locations shown to replace the L P gas orifice spuds NOTE Depending on model the range cooktop may be equipped with 4 standard burners or 3 standard burners and 1 power burner Spud size location remain the same Remove and replace orifice spuds orifice spuds notches NOTE Burner tube and brackets not shown gas manifold 445 52 A o G CJ Gy L R L F R R R F Place L P gas orifice spuds in plastic parts bag for future use and keep with literature package
14. ertified flexible metal appliance connector 4 5 feet or rigid gas supply line as needed e insulated pad or 1 4 plywood if range is installed over carpeting Parts supplied for installation anti tip bracket Q q Not shown e literature pack orifice spu W 2 plastic anchors Bracket must be securely mounted to sub floor Thickness of flooring may require longer screws to anchor the bracket to sub floor ds Ys screws 10 x 1 1 2 Product dimensions 26 3 4 67 9 cm depth with handle Proper gas supply connection must be available See Gas supply requirements Page 4 46 1 4 117 5 cm overall height for tall backguard models Grounded electrical outlet is required See Electrical requirements Page 4 aN 24 1 4 61 6 cm 29 7 8 75 9 cm lt _ lt width 18 45 7 cm min clearance upper side cabinet to countertop I This shaded area recommended for electrical outlet Contact a qualified floor covering installer to check that the floor covering can withstand at least 200 F Use an insulated pad or 1 4 plywood under range if installing range over carpeting g depth 30 76 2 cm min i cabinet opening width For minimum materials used will not discolor delaminate or sustain 30 1 8 76 5 cm a 61 i j 3 7 6 cm Opening width 2 5 1 cm min countertop space
15. g codes and ordinances This installation must conform with all local codes and ordinances In the absence of local codes installation must conform with American National Standard National Fuel Gas Code ANSI Z223 1 latest edition Input ratings shown on the model serial rating plate are for elevations up to 2 000 feet For assistance when installing the range at higher elevations contact your local service company Type of gas This range is design certified by CSA International for use with L P gas or after proper conversion for use with Natural gas This range is factory set for use with L P gas Gas conversion instructions are provided on pages 8 9 The model serial rating plate located on the frame behind the broiler drawer has information on the type of gas that can be used If the type of gas listed does not agree with the type of gas available check with the local gas supplier Conversion must be done by a qualified service technician Gas supply line Provide a gas supply line of 3 4 rigid pipe to the range location With L P gas piping or tubing size can be 1 2 minimum A smaller size pipe on longer runs may result in insufficient gas supply Usually L P gas suppliers determine the size and materials used in the system Pipe joint compounds made for use with L P gas must be used on pipe threads only Copies of the standards listed may be obtained from National Fire Protection Association One
16. he gas supplier IMPORTANT Observe all governing codes and ordinances Do not obstruct flow of combustion and ventilation air This installation must conform with all local codes and ordinances In the absence of local codes installation must conform with American National Standard National Fuel Gas Code ANSI Z223 1 latest edition It is the customer s responsibility e To contact a qualified electrical installer e To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all codes and ordinances Cabinet opening dimensions shown must be used Given dimensions are minimum clearances To eliminate the risk of burns or fire by reaching over heated surface units cabinet storage space located above the surface units should be avoided If cabinet storage is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 inches 12 7 cm beyond the bottom of the cabinets Proper installation is your responsibility A qualified technician must install this range Make sure you have everything necessary for correct installation It is the installer s responsibility to comply with installation clearances specified on the gas information label The gas information label and model serial rating plate are located on the frame behind the broiler door Mobile home installation Th
17. ide for a toll free number to call or call the dealer from whom you purchased this appliance The dealer is listed in the Yellow Pages of your phone directory under Appliances Household Major Service and Repair If you need service Maintain the quality built into your range by calling an authorized service company To obtain the name and number of the authorized service company S Contact the dealer from whom you purchased your range or S Look in the Yellow Pages of your telephone directory under Appliances Household Major Service and Repair or S Call the Customer Interaction Center The toll free number is listed in your Use and Care Guide When you call you will need S The range model number S The range serial number S Call the Customer Interaction Center Both numbers are listed on the model serial rating plate located on the frame behind the broiler door 11 Part No 98015194 an Printed in Mexico 2004 Whirlpool Corporation Benton Harbor Michigan 49022 1 04
18. inct blue flame 1 4 6 4 mm to 1 2 1 3 cm long The outer cone is not as distinct as the inner cone The oven burner flame should be 1 2 1 3 cm long with a bluish green inner cone and dark blue outer mantle L P gas flames have a slightly yellow tip If the flames are noisy or blowing they are getting too much air If the flames are soft and lazy they are not getting enough air If burners need adjusting see Check operation section Steps 17 22 Page 7 9 Close the broiler door Turn oven control knob to OFF 1 0 m Remove control knobs Reinstall the control panel Securely tighten the 4 screws Reinstall the control knobs IMPORTANT If not done in Step 8 check the LO flame adjustment See Check operation section Step 19 Page 7 Moving the range 4 WARNING 4 Tip Over Hazard A child or adult can tip the range and be killed Connect anti tip bracket to rear range foot Reconnect the anti tip bracket if the range is moved Failure to follow these instructions can result in death or serious burns to children and adults When moving range slide range onto cardboard or hardboard to prevent damaging the floor covering If removing the range is necessary for cleaning or maintenance Unplug range or disconnect power 2 Shut off the gas supply to the range 3 Disconnect gas 4 Slide range forward to complete cleaning or maintenance 5 Making sure th
19. ntrol knob to the LO setting and remove control knob Insert a small flat blade screwdriver into the valve stem Turn the valve screw to obtain the smallest flame that will not go out when the control of a cold burner is quickly turned from HI to LO Repeat for other cooktop burners as needed Check operation of oven broil burner OFF 140 1706 200 250 e a e 300 7 350 400 OVEN TEMP 20 m Open broiler door Push in and turn the oven control knob to 350 F The oven burner should light in 20 40 seconds this delay is normal The oven valve requires a certain time before it will open and allow gas to flow To avoid damaging the hot surface ignitor do not insert any object into the openings of the protective shield that surrounds the ignitor or clean that area 2 1 Check the oven burner for proper flame The flame should be 1 2 1 3 cm long with inner cone of bluish green and outer mantle of dark blue and should be clean and soft in character No yellow tips not enough air blowing or lifting too much air of flame should occur If oven flame needs adjusting a Turn the oven off Wait for the oven burner to cool down b Open oven door and remove oven racks oven tray flame spreader and set aside A Wt lift up to remove c Locate the air shutter near the rear wall of oven and loosen the shutter screw Ps shutter screw air shutter d Adj
20. or the best procedure for drilling mounting holes through your type floor covering 4 Use the anti tip bracket template instruction sheet to install the anti tip bracket Anti tip bracket must be anchored securely to the sub floor Depending on the thickness of your flooring longer screws may be needed to anchor the bracket to the sub floor Longer screws are available from your local hardware store 5 Check that range is still on cardboard shipping base to protect floor covering Move range close to final location 6 Remove cardboard shipping base from under range Open broiler door Use a 3 8 drive ratchet to lower rear leveling legs one half turn Use slip joint pliers to lower front leveling legs one half turn front leveling leg CS C N rear x leveling leg CTT 7 Making sure the anti tip bracket is installed e Look for the anti tip bracket securely attached to floor e Slide range back so rear range foot is under anti tip bracket anti tip bracket range foot 3 If installing the range in a mobile home you must secure the range to the floor Any method of securing the range is adequate as long as it conforms to the Manufactured Home Construction and Safety Standard Page 2 9 Place rack in oven Place level on rack first side to side then front to back If range is not level pull range forward until rear leveling leg is removed from
21. spuds in plastic parts bag for future use and keep with literature package Reinstall burner tube and bracket assemblies Remove and replace orifice spuds orifice spuds NOTE Burner tube and brackets not shown 65 62 A A o o w L R L F e Lower cooktop Reinstall screws to secure burner tubes to cooktop Reinstall burners burner caps and burner grates Do not reinstall control panel or knobs They will be reinstalled in Step 10 6 Oven burner a Open oven door and remove oven racks oven tray flame spreader and set aside Lift oven burner The orifice spud is behind the oven burner air shutter b Locate L P gas orifice spud stamped 56 in literature package supplied with range c Use a 3 8 combination wrench and remove the natural gas orifice spud Install the number 56 L P gas spud Place natural gas oven burner spud in plastic parts bag along with natural gas cooktop burner spuds for future use and keep with literature package d Reinstall the oven burner te te te te c oven burner orifice behind air shutter L P oven orifice spud stamped with 56 S D 7 Turn manual shutoff valve in gas supply line on If Gas and electrical connection Steps 10 16 on Page 6 were not completed complete them now 8 Install control knobs Check for proper flame The cooktop burner flames should have a small inner cone with a very dist
22. to side wall or other combustible material 24 0 cm 13 33 cm max upper cabinet Check location where range will be installed The range should be located for convenient use in the kitchen Recessed installations must provide complete enclosure of the sides and rear of range All openings in the wall or floor where range is to be installed must be sealed IMPORTANT Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self cleaning Check with your builder or cabinet supplier to make sure that the clearance to top Other damage of cooktop see NOTE NOTE 24 61 cm min when bottom of wood or metal cabinet is protected by not less than 1 4 0 64 cm flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 0 4 mm stainless steel 0 024 0 6 mm Bo aluminum or 0 020 0 5 mm copper 30 76 2 cm min clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet This shaded area recommended for installation of gas pipe Do not seal the range to the side cabinets If cabinet depth is greater than 24 61 cm oven frame must extend beyond cabinet fronts by 1 2 1 3 cm min Anti tip bracket The floor anti tip as 10 25 4 cm bracket must be am Ce cm t t 12 7 cm installed To install 5 1 cm 5 12 7 cm the anti tip
23. ust the air shutter e Turn the oven back on and check for proper flame If the flame is still not properly adjusted turn the oven off wait for the oven burner to cool down and repeat Step d until flame is properly adjusted f When the flame has been properly adjusted turn the oven off wait for the burner to cool down and tighten the shutter screw 22 m Replace flame spreader and oven tray Replace the oven racks and close oven door Close the broiler door You have just finished installing your new range To get the most efficient use from your range read your Use amp Care Guide Keep Installation Instructions and Guide close to range for easy reference The instructions will make installing the range in another home as easy as the first installation Gas conversion Gas conversions from L P gas to Natural gas or from Natural gas to L P gas must be done by a qualified installer 4 amp WARNING A Fire Hazard Shut off gas supply line valve Make all conversions before turning gas supply valve back on Failure to follow these instructions can result in explosion fire or injury Natural gas conversion 1 Complete installation Steps 1 9 Pages 5 6 before converting range to Natural gas Check that the manual shutoff valve in the gas supply line has been turned off 2 m Open broiler drawer and remove broiler pan The pressure regulator is located in the back right hand corner of the broil
24. wing it is getting too much air If the flame is soft and lazy it is not getting enough air Turn each surface burner control knob to OFF position Adjust air shutter if needed Check each cooktop burner for proper flame The small inner cone should have a very distinct blue flame 1 4 6 4 mm to 1 2 1 3 cm long The outer cone is not as distinct as the inner cone If the flame is OFF MED If surface burner air shutters need adjusting a Remove control knobs and 4 screws that attach control panel to range cabinet Pull control panel forward to remove Set panel screws and knobs aside Cio i i To 4 screws b Replace control knob for burner to be adjusted Push knob in and turn to LITE position When burner lites turn to HI position c Adjust the air shutter by hand as needed Close the air shutter to decrease the amount of air to the flame Open the air shutter to increase the amount of air to the flame air shutter Adjust the air shutter to the widest opening that will not cause the flame to lift or blow off the burner Turn burner off and remove knob As needed adjust other air shutters 1 83 Replace control panel and tighten screws securely Replace control knobs 1 9 Push in and turn each cooktop control knob from LITE to LO setting quickly The low flame should be a minimum steady blue flame If flame needs to be adjusted turn co
Download Pdf Manuals
Related Search
Related Contents
Bedienungsanleitung 木製オープンワゴン 取扱説明書 FM/AM Digital Media Player Platform User Manual - Precision Weighing Balances Presents MPL-28-02V1.00/USBW32 MPL-28 Citation 商学討究 (2014), 64(4): 345-348 Issue Date 2 - Barrel Document converted with www.koolwire.com Serie HB73 Manuale d`uso - Honeywell Video Systems Copyright © All rights reserved.
Failed to retrieve file