Whirlpool 1982 Oven User Manual
Contents
1. panel See View A SCREW 1 Each Side VIEW A 2 Put an allen wrench 5 32 or smaller or equivalent in the hole in each of the hinges Close the oven door until the pins touch the oven front See View B 3 The oven door can now be lifted off 4 Reinstall oven door the same as on non self cleaning models See page 4 5 Reinstall the door mounting screws With the door off you will notice how the ends of the hinges slide into slots at the bottom corners of the door To put the door back on fit both bottom corners of the door over the ends of the hinges Push the door down evenly so neither corner gets ahead of the other When it reaches the bottom you can close the door A safety latch will hold the door open until it is on correctly 4 CHECKING CAUTION Do not touch the elements They may be hot and you may get burned A THERMOSTAT 1 Broil Turn selector switch to BROIL and set thermostat to a high temperature position The top element should become cherry red and the indicator light should glow 2 Bake Turn selector switch to BAKE and set thermostat to 350 The bottom element should become red and the indicator light should glow B CLOCK VIEW B Refer to the Use and Care Guide for proper operation of TO REMOVE OVEN DOOR ores NON SELF CLEANING MODELS C ROTISSERIE if optional kit has been installed 1 Position the spit bar on special rack 2 Insert the point of spit bar into hole in2. quality originally built into your WHIRLPOOL appliance WHIRLPOOL CORPORATION BENTON HARBOR MICHIGAN 49022 Part No 311434 Rev D 4
3. Installation Instructions your new ELECTRIC BUILT IN OVEN 30 SINGLE OVEN MODELS STARTING WITH 1982 MODELS 1 Min 2954 48 INCH FLEX CABLE FOR A 36 OPEN OVEN DOOR HEIGHT FIGURE 1 ROUGH IN DIMENSIONS NU HOLE IN OVEN SUPPORT SURFACE FOR CABLE OVEN SUPPORT SURFACE 12 Max L CABINET T FRONT 1 SEE NOTE 1 MIN 28 MINIMUM IF 28 5 8 IS AVAILABLE THE CUTOUT SHOULD BE MADE 28 5 8 DO NOT INSTALL THIS OVEN IN A BASE CABINET WITH A COUNTERTOP ABOVE IT 1 CARPENTRY Reter to Figure 1 for the dimensions of the oven and the space necessary to receive the oven The oven support surface may be solid plywood or similar material but the contact surface must be level from side to side and from front to rear This surface is 234 below the open door height NOTE 1 The oven support surface must be flush with the bottom of the cabinet cut out WARNING TO AVOID DAMAGE TO CABINET AND OR POOR BAKE PERFORMANCE DO NOT BLOCK OVEN VENT 2 ELECTRICAL REQUIREMENTS IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR S USE A A three wire or four wire single phase 120 240 volt 60Hz AC only electrical supply or three wire or four wire 120 208 volt if specified on nameplate is required on a separate circuit fused on both sides of the line time delay fuse or circuit breaker is
4. inances This appliance is manufactured with a white neutral power supply wire and a frame connected green ground wire 1 Iflocal codes permit connection of the frame ground ing conductor to the neutral white wire connect the green and white wire from the supply cable of the appliance together and to the neutral white wire in the junction box Connect the remaining wires from the supply cable matching the colors to the wires in the junction box 2 If local codes DO NOT permit frame grounding to the neutral separate the white and green wires that extend out of the end of the supply cable of the appliance Connect the white wire from the supply cable to the neutral wire in the junction box Connect the black and red wire from the supply cable matching the colors to the corresponding wires in the junction box The green wire MUST now be used to ground the appliance in accordance with local electri cal codes Connect the green ground wire to a grounded cold water pipe or to the grounded lead in the service panel Do not ground to a gas supply pipe Do not connect to electrical power supply until appliance is permanently grounded Connect the ground wire before turning on the power See Figure 2 GROUNDED COLD COPPER WATER PIPE GROUND WIRE TIGHTEN NUTS FIRMLY GROUND CLAMP MUST BE TIGHT ON PIPE FIGURE 2 Cold water pipe must have metal continuity to electrical ground and not be interrupted by plastic rubber
5. or other electrically insulating connectors including water meter or pump without adding a jumper wire at these connec tions CAUTION If connecting to a four wire electrical system MOBILE HOME the appliance frame MUST NOT be connected to the neutral wire of the four wire electrical system Separate the white and green wires that extend out of the end of the supply cable of the appliance Connect the white red and black wires from the supply cable matching the colors to the corresponding wires in the junction box Connect the green wire from the supply cable to the ground wire in the junction box REMOVE PAINT ETC 3 INSTALLATION NOTE Before installing the oven in the cutout it may be helpful to remove the oven door See details below Insert appliance into cut out Screws are provided for fastening the front frame of the appliance to the cabinet The mounting holes in the front frame of appliance may be used as a template to locate the appliance mounting screw holes CAUTION For your personal safety and to minimize potential personal injury this oven must be securely fastened to the cabinet using the four screws that are provided Use caution when mounting oven in cutout so you do not overtighten screws and cause porcelain chippage or puncture oven cavity TO REMOVE OVEN DOOR SELF CLEANING MODELS Door to be removed for installation only 1 Remove the two screws one on each side of the inner door
6. recommended Do NOT fuse neutral The fuse size must not exceed the circuit rating of the appliance specified on the nameplate NOTE Wire sizes and connections must conform with the fuse size and rate of the appliance in accordance with the National Electrical Code and local codes and ordinances Do not use an extension cord ad The appliance should be connected to the fused discon nect or circuit breaker box through flexible armored or non metallic sheathed cable The flexible armored cable extending from the appliance should be connected directly to the junction box The junction box should be located as shown in Figure 1 so that as much slack as possible remains in the cable between the box and the appliance so that it can be moved if servicing is ever necessary C A suitable strain relief must be provided to attach the flexible armored cable to the junction box D Electrical Connection It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code and local code ordinances Electrical ground is required on this appliance This appliance is equipped with copper lead wires If the connection is made to aluminum house wiring use only special connectors which are approved for joining copper and aluminum wires in accordance with the National Electrical Code and local codes and ord
7. the back of the oven 3 Rotation starts upon insertion of spit bar Push down evenly Pull straight with the angle of part open door Removing the oven door For installing and cleaning Removing the oven door may make it easier to clean the oven To remove the door first open it to the first stop about 4 inches or 10 cm Take hold of both sides of the door near the top then lift it at the same angle it is in In the event your WHIRLPOOL appliance should need service call the dealer from whom gt you purchased the appliance or a WHIRLPOOL franchised TECH CARE service company dv He is in the Yellow Pages of your telephone directory listed under Appliances Household Wh Major Service and Repair You can also obtain his name and number by dialing free within 1T Oo the continental United States the Whirlpool COOL LINE Service 800 253 1301 When calling from Michigan dial B00 632 2243 from Alaska or Hawaii dial 800 253 1121 Fredo TECH CARE FRANCHISED SERVICE Dial just as you normally dial long distance A special operator will tell you the name and number of your nearest Whirlpool TECH CARE service outlet During normal working hours Whirlpool consultants at this same number will also answer any questions about operating or ECH CARE maintaining your appliance not covered in your Use and Care Guide FRANCHISED SERVICE Learn the benefits of using TECH CARE service for maintaining the
Download Pdf Manuals
Related Search