Ultra Start 430 Automobile Alarm User Manual
Contents
1. 2 When in program Mode change the desired Program Setting by pressing the transmitter buttons in the following sequences NOTE The Systems Default Setting Are Shown In Bold Lettering 9 aA2 IR O 3 Quick View Programming Programmable Feature Press Buttons One Chirp Two Chirps Shock Sensor Disable 3 3 1 Disabled Enabled Arm Disarm Chirps 2 1 1 Chirps Off Chirps On Ignition Auto Locks 1 3 2 Off On Door Lock Timing 1 3 1 3 Second 75 Second Double Pulse Unlock 2 2 1 Two Pulses Single Pulses Door Input Voltage Sense 1 1 3 Voltage Door Pin Passive Active Locks 3 3 2 Active Passive Passive Active Arming 1 2 3 Active Passive Car Jack Mode 2 1 3 Deactivated Activated Siren Horn Output 3 2 1 Siren Horn System Reset 3 3 3 Confirmed by Three Siren Chirps CJ series ONLY 441 series ONLY INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 8 Enter Program Mode Entering program mode is done by the following steps 1 Make sure ignition is in the off position 2 Turn the ignition key ON OFF leaving key in the OFF position 3 Press and release the Valet button two times 4 The siren will chirp one time to confirm entering program mode If this does not happen turn ignition off wait five seconds and repeat steps 1 4 Shock Sensor Disable 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the follo2. of the switch is picked use a 1 4 drill bit and drill a hole Remove the nut and push the Program Button through the hole Replace the nut and tighten until the switch is secure Plug the Program Button into the Blue connector of the main module Basic Install Step 1 Connect All Of the Following Wires Black Ground Input System ground input Yellow Ignition Input Input from vehicles ignition wire Red Power Input Constant 12 Volt input Brown Siren Output Positive output for siren White Park lights Positive park light output Green Door Input Negative door pin switch input Purple Door Input Positive door pin switch input Test for door pin type or then connect the appropriate wire Step 2 Plug In The Module Step 3 Test And Adjust The Shock Sensor see page 3 Step 4 Test The System Your Basic Install Is Complete REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 7 Programming To Enter Program Mode 1 Make sure ignition is in the off position 2 Within three seconds turn the key ON the OFF 3 Press and release the Program Button two times 4 The siren will chirp and the lights will flash once to confirm NOTE f unit does not enter Program Mode repeat steps 2 3 The ignition input wire yellow on the 10 pin connector MUST be connected If it is not connected it will not be possible to enter the Program Mode Changing A Programmable Setting 1 Enter Program Mode As explained above
3. with the following 3 Chirps System Reset NOTE Repeat sequence to change selection INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 10 Transmitter Programming Follow the steps below to program the transmitters to the system s memory Step 1 Turn the Ignition key ON then OFF Leaving Key Off Step 2 Press and release the Program Button twice then press and hold Step 3 The siren will respond with five chirps to confirm Transmitter Program Mode Note If the siren does not respond repeat Steps1 amp 2 Step 4 Continue to hold the Program Button and press lock button on each of the transmitter s to be programmed Maximum of 3 Different transmitter codes Step 5 The system will respond with a siren chirp each time a transmitter is programmed Exit After five seconds the system will exit transmitter program mode automatically NOTE You must program ALL of the transmitters to be used at one time For the owner s security any transmitters not programmed at this time will be erased from memory This system will store a maximum of three transmitter codes in memory Car Jack Mode Activation CJ series ONLY 1 If the ignition key is On and a door is opened the Car Jack Mode Timer will start The siren will chirp one every second for 10 seconds then trigger into full alarm 2 If the timer was activated by accident within 10 seconds turn the ignition key back to On then press and release the program button one time The C
4. INSTALL GUIDE Covers All 430 440 441 and CJ Series Advanced Security Systems REMOTE STAPTERS CAR ALARMS www ultrastarters com Technical Support 866 698 5872 ext 0 support ultrastarters com Note Some features may not be available on certain models FCC ID Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance void the user s authority to operate this devise INSTALL MANUAL PAGE 2 Table of Contents Table Of Contents REMOTE VEHICLE SECURITY Page 2 Components Wiring Diagram With 10 pin connector Wiring Diagram With 11 pin connector Page 3 Page 4 Wiring Description Pages 5 6 Recommended Installation Procedures Basic Installation Quick start Shock Sensor Adjusting Test The System Programming Page 7 9 Program Overview Quick View Programming Program Menu System Reset Transmitter Programming Car Jack Mode CJ series Only System Operation Page 10 Page 11 Relay Diagrams COMPONENTS Three Button Remote transmitter s 430 Series Four Button Remote transmitter s 440 Series Plug in Valet Switch Program Switc
5. ar Jack Mode Timer will stop 3 If the timer is not deactivated Car Jack Mode will trigger into full alarm To deactivate turn the ignition On then press and release the program button 5 times then press unlock on the remote transmitter Emergency Override If Car Jack Mode is not deactivated in time the system will need to be placed into Emergency Override Turn the ignition key to the On position then press and hold the program button for 20seconds At this time the customer can bring the vehicle back to the dealer fora system reset REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 11 Alarm Functions Arm 1 Press and release the button 2 The park lights will flash and the siren will chirp one time 3 The doors will lock optional NOTE The LED will start flashing within five seconds If installed the starter disable will activate Disarm 1 Press and release the button on the remote transmitter 2 The park lights will flash and the siren will chirp two times 3 The doors will unlock optional NOTE The LED will stop flashing If installed the starter disable will deactivate Silent Arm Disarm 1 Press and release the button then press and release the button to silent arm The park lights will flash once to confirm 2 Press and release the button then press and release the button to silent disarm The park lights will flash twice to confirm Panic 1 Press and hold the button on the remo
6. ckwise a ff E Decrease Sensitivity Turn the adjustment screw counter clockwise Ka m 500ma outputs are low current and are designed to activate relays INSTALL MANUAL PAGE 4 For modules with 11 pin connector only REMOTE VEHICLE SECURITY 500ma Programmable lock output Lock Output Green 3 Low current output for voltage inverter 12v Constant Red bi 500ma Programmable unlock output Unlock Output Blue 8 C Connect to park lights 15amp Maximum Park Lights White 500ma negative output When Armed Orange 500ma negative output Trunk Release H Gray z Connect to constant power 20amp input 12 Volt Input Red Connect to Siren wire 2amp Maximum Siren Output Brown z Connect to chassis ground Ground Input Black 3 Connect to hood and or trunk pin Hood Input Blue H Connect to door pin when opened Door Input Green Connect to vehicles ignition wire Ignition Input Yellow Connect to door pin when opened Door Input Purple Dome Light Supervision Output Dome Light BIk White LED T Red 1 Program Switch E _ Blue Shock Sensor Adjustment Increase Sensitivity Turn the adjustment s
7. crew clockwise Decrease Sensitivity Turn the adjustment screw counter clockwise 500ma outputs are low current and are designed to activate relays REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 5 Wiring Descriptions 10 Pin 11 Pin Connector White Park lights Park light output Orange When Armed Negative output when system is armed Grey Trunk Release Negative output for trunk release Yellow Ignition Input Input from vehicles ignition wire Red 12Volt Input Constant 12 Volt input Brown Siren Output Positive output for siren Black Ground Input System ground input Purple Door Input Positive door pin switch input Green Door Input Negative door pin switch input Blue Hood Input Negative input from hood pin switch Bik White Dome Supervision 30 second output when disarmed This wire is only available on models with the 11 pin connector 3 Pin Connector Red Green Door Lock Door Lock Output Programmable Red 12 Volt Output 12Volt Output for voltage inverter Blue Door Unlock Door Unlock Output Programmable NOTE 500ma outputs ONLY Recommended Installation Procedures Mounting the module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceab
8. h 10 Pin Main Harness 2 pin Keyless Entry harness Page 12 Control Module Plug in Led Multi Tone Siren Installation Guide Owners Manual REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 3 For modules with 10 pin connector only See page 4 for 11 pin connector 500ma Programmable unlock output Unlock Output Blue E S Low current output for voltage inverter 12v Constant Red gt 500ma Programmable lock output Lock Output Green i Connect to park lights 15amp Maximum Park Lights White 500ma negative output When Armed Orange 500ma negative output Trunk Release Gray z Connect to vehicles ignition wire Ignition Input Yellow i 5 Connect to constant power 20amp input 12 Volt Input Red F Connect to Siren wire 2amp Maximum Siren Output Brown Connect to chassis ground Ground Input Black 3 Connect to door pin when opened Door Input Purple a Connect to door pin when opened Door Input Green Connect to hood and or trunk pin Hood Input Blue Program Switch O 5 Blue LED C 8 Red Shock Sensor Adjustment Increase Sensitivity Turn the adjustment screw clo
9. le areas Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a thief The module must be free from all moving parts Under Hood Connections Route the hood pin optional and Siren wire through the firewall into the engine compartment Always try to pull the wires through a factory rubber grommet If drilling through the firewall BE CAREFUL Check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Mounting the Siren Choose a location in the engine compartment that is away from high heat sources and direct exposer to water The siren should be mounted as well as grounded to solid metal Run the wiring for the siren so that it can not be seen or reached from below the vehicle INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 6 Recommended Installation Procedures Installing the LED Choose a location that will be highly visible when the LED is installed Most vehicles are equipped with knock out panels in the dashboard these panels are easily removable and can be easily replaced if necessary Once the location is picked use drill bit and drill a hole through the panel Test fit the LED into the hole Plug the Led into the Red connector on the main module Installing the Program Button Choose a location to mount the Program Button This location should be hidden and not visible from outside the vehicle Once the location
10. n the following sequence 1 1 then 3 3 The siren will respond with the following 1 Chirp Voltage Sensing No Door Pin Connection Needed 2 Chirps Door Pin Door Pin Connection Required Passive Active Locks 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 3 3 then 2 3 The siren will respond with the following 1 Chirp Active Locks 2 Chirps Passive Locks Passive Active Arming 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 2 then 3 3 The siren will respond with the following 1 Chirp Active Arming 2 Chirps Passive Arming Car Jack Mode CJ series ONLY 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 2 1 then 3 3 The siren will respond with the following 1 Chirp Inactive 2 Chirps Active Siren Horn Output 441 series ONLY 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 3 2 then 1 3 The siren will respond with the following 1 Chirp Siren 2 Chirps Horn Reset System 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 3 3 then 3 3 The siren will respond
11. te transmitter 2 The park lights will flash and the siren will sound 3 Press and release the or the button to deactivate Panic will be active for 60 seconds or until disabled by the remote transmitter Trunk 1 Press and hold the button for 3 seconds 2 The doors will unlock optional continue holding until the Trunk Release activates Car Finder 1 Press and hold the button for 3 seconds 2 The park lights will flash and the siren will chirp 5 times INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 12 Relay Wiring Diagrams Negative Type Door Locks f Tel Vehicle Lock To Control Lock Unlock U Relay or Oo Switch n Actuators lock Green TI Blue Positive Type Door Locks Vehicle SI Fused 12V Lock Unlock Switch f Green Blue TT o Control Relay or Actuator Fused 12V Vehicle Lock Unlock Switch To Actuator Negative Park Lights In some cases the park lights may flash erratically after installing the negative park light relay To correct this issue add a diode between the coil pins of the relay as shown Add IN4001 Diode a7 as shown fms 7 oO White 86 C188 Ground Negative park light output
12. wing sequence 3 3 then 1 3 The siren will respond with the following 1 Chirp Shock Sensor OFF 2 Chirps Shock Sensor ON Arm Disarm Chirp 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 2 1 then 1 3 The siren will respond with the following 1 Chirp Chirps Disabled 2 Chirps Chirps Enabled Ignition Auto Locks 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 3 then 2 3 The siren will respond with the following 1 Chirp Auto Lock Disabled 2 Chirps Auto Lock Enabled Door Lock Timing 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 3 then 1 3 The siren will respond with the following 1 Chirp 3 Second Door Locks 2 Chirps 0 75sec Pulses Double Pulse Unlock 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 2 2 then 1 3 The siren will respond with the following 1 Chirp Double Pulse Unlock 2 Chirps Single Pulse Unlock NOTE Repeat sequence to change selection REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 9 Voltage Door Pin Sensing 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons i
Download Pdf Manuals
Related Search