U-Line U-2115RS-02 Refrigerator User Manual
Contents
1. 12 Adjusting the door as needed Depending on installation bottom of overlay may NOT align with bottom of door 7 Attach the door to the overlay using 6x1 wood screws NOTICE If you decide to drill pilot holes remove the wood overlay from the door and do not use a drill larger than 7 64 Be sure not to drill deeper than 3 8 The door frame and wood overlay must be aligned properly or the door will not operate correctly Note After attaching the wood to the door double check the bottom pivot hole location If the hole in the pivot bracket is covered by any wood chase through the hole with a 1 1 32 drill to open hole in door panel DO NOT drill deeper than 1 4 u line com 19 Il Installation Leveling Information It is recommended that the unit is level 13 Use a level to check the levelness of the unit from front to back and from side to side Level should be placed along top edge and side edge as shown 14 If the unit is not level adjust the feet on the corners of the unit as necessary not available in CO29 models 4 f f J i u i SS f Hy Turn Foot to Adjust 15 Check the levelness after each adjustment and repeat the previous steps until the unit is level INSTALLATION TIP If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a2. For best performance keep the unit out of direct sunlight and awav from heat generating equipment a kk In climates where high humiditv and dew points are present condensation mav appear on outside surfaces This is considered v y A Ba Md normal The condensation will evaporate when the humidity drops u u u u l PRA I A 21 I5RSOD amp 2175SOD Models For best performance and life u 1 2 1 2 i 90 s u outdoors place under a counter or provide shelter of some kind Door Swing li Door Swing li u u Y Y Wy WY Wood Overlay Stainless Steel u line com 6 Doors Self Closing Door Alignment and Adjustment Align and adjust the door if it is not level or is not sealing properly If the door is not sealed the unit may not cool properly or excessive frost may form in the interior NOTICE Properly aligned the door s gasket should be firmly in contact with the cabinet all the way around the door no gaps Carefully examine the door s gasket to ensure that it is firmly in contact with the cabinet Also make sure the door gasket is not pinched on the hinge side of the door The door will not be flush with the top of the cabinet The top edge of the door will be 1 8 in 3 175 mm below the cabinet top 1 8 3 175 mm To align and adjust the door Compare the top edge of the door opposite the hinges to the top edge of the cabinet and note the type up or
3. 414 354 5696 Milwaukee Wisconsin 53224 9540 U S A Email onlineservice u line com Phone 1 414 354 0300 u lineservice com FAX 1 414 354 7905 Email sales u line com PARTS ASSISTANCE u line com E mail onlineparts u line com BUILDING ON THREE GENERATIONS OF INNOVATION For over five decades and through three generations U Line continues to be the leader in innovation quality and performance in the premium built in undercounter ice making refrigeration and wine preservation market U Line has captivated those with an appreciation for the finer things with exceptional functionality style inspired innovation and attention to even the smallest details We are known and respected for our unwavering dedication to product design quality and selection In 1962 Henry Uihlein founded U Line Corporation as an outgrowth of Ben Hur Freezer Company and was the first to develop and patent an automatic stand alone undercounter residential ice maker His foresight and determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today The newest Uihlein generation continues to build upon the family s innovative legacy at the Milwaukee Wisconsin based business by providing continuity and vision from which new designs and technology continue to be born Today the complete U Line product collection includes Ice Makers Ice Machines Wine Captain Models Combo Models Refrigerator Freezers Refrigerator
4. Align and adjust the door see DOOR ALIGNMENT AND ADJUSTMENT on page 7 u line com 7 Wood Trim Finishing To prevent permanent damage to the inner liner of the unit the wire rack wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours in accordance with the stain finish manufacturer instructions prior to re installing the wood trim inside the cabinet of the unit Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty NOTICE Your model may contain an electronic display panel in the lowest level trim piece After removing the trim screws and gently pulling the trim from its location a wiring harness connector will become visible Unplug the connector and remove the trim from the interior Glass in door is tinted Stain may look darker when door is closed Removing Wire Racks I 2 3 4 Grasp the end of the rack and gently slide it out until it stops Remove any bottles stored on the rack Press the left rack release lever see above down and at the same time lift the corresponding right rack release lever up and pull the rack out until it is free of the tracks and the cabinet Do not remove the track side rails from the cabinet To insert a rack in the cabinet Align the left and right rack channels with the tracks in the cabinet and ensuring an ev
5. Side Installation Power Supply Environmental Requirements ann uuu 6 Doors Self Closing Door Alignment and Adjustment nnnennennenrennrveneenvenneenenseensseneensennenneenseenveursenvenseenenneenseenvenseene Door Reversabilitylzzinmi i e pepe base Bon pn I Reversing Black or White Doors Reversing Stainless Steel Glass Doors 7 Wood Trim Finishing Staining and final finish application iii 12 Final finish only application ann u nn 12 8 Door Panel Installation Custom 1 4 Thick Door Panel Insert u iene ieri 13 Door Panel Preparation aa 13 Panel Dimensions zat 03 Door Panel Installation isse inizzel 13 9 Wood Grille Overlay Grille Overlayn gir ekeren eee lie ill ille 14 Prep ratiOn ws e AREA ARA ALARE apana RAI RI 14 Installation susino near pp aun Qanaq utqa INNI PALIO 14 10 Overlay Frame Frame Preparatio ri su naam aquqa qusaqa Abba atti I7 Prepare the New Overlay Panel 18 Attaching the Overlay Panel iii 18 Assembling Door to Cabinet nnvunseunenreenreencenvenneeneenseenseaneenvensenneenseenvenneenvensennenneensen 19 II Installation Leveling Informations a abu Vet Boat logici 20 Installation i ai 20 Relocating the Shelves 20 Installation Wii 20 Safety Precautions NOTICE PLEASE READ all instructions before installing operating or servicing the appliance Proper ins
6. a 45 angle then straight out Choose new location and line up on bosses First push straight in then down at a 45 angle Installation Troubleshooting aq Problem The door remains open unless it is pushed closed A Solution The hinges should be self closing when the door is open approximately 8 If this is not the case make sure the closers are clean greased and installed correctly Also re check leveling from front to back of the unit and readjust if necessary Make sure that pivot plate is installed correctly Problem The custom overlay door was designed to align with the rest of the cabinet doors but the unit has crept forward A Solution Make sure that the electrical cord and water supply line are not obstructing the installation 20 u line com INSTALLATION GUIDE U LINE PRODUCT INFORMATION Complete Installation Guides Use and Care Guides Specifications amp Features and Benefits CAD Drawings Overlav Panel Frame and Toe Kick Specifications and Instructions Compliance Documentation and Applicable Energv Guides are available for reference and download at u line com SERVICE INFORMATION Please consult vour Use and Care Guide for troubleshooting information Answers to Customer Frequentiv Asked Questions are available at u line com under Customer Service You may contact U Line directly GENERAL INQUIRIES SERVICE ASSISTANCE U Line Corporation Phone l 800 779 2547 P O Box 245040 FAX l
7. down of door is parallel with top of cabinet and tighten screws 1 securely 5 After adjustment is complete remove the door closers from the bottom hinge clean thoroughly and apply petroleum jelly to the mating surfaces of the closers Be sure that pins on closers align with holes in the door and bottom cabinet hinge plates Mount door and install top hinge pivot pin Door Reversability Location of the unit may make it desirable to mount the door on the opposite side of the cabinet Many doors are reversible See adjustment needed AS 2 lt gt 3 D Remove the top hinge pivot pin with a Phillips screwdriver and lift door off bottom hinge pin Be careful not to lose the door closer insert sets tu Turn the door upside down and inspect the hinge plate mounting holes The plate has slotted mounting holes Loosen but do not remove the two hinge plate screws 1 If door edge opposite the hinges needs to move up move plate toward outside of door 2 If door edge needs to move down move plate toward inside of door 3 Repeat until top edge of u line com table below Model Reverse Model Reverse U 2115RB 00 YES U 2175WCCOL 02 YES U 2115RS 00 NO U 2175WCCOL 60 YES U 2115RS 01 NO U 2175WCCS 00 YES U 2115RS 02 NO U 2175WCCS 02 YES U 2115RSOD 00 NO U 2175WCCS 13 YES U 2115RSOD 01 NO U 2175WCCS 22 YES U 2115RVW 00 YES U CLR2160B 00 YES U 2115WC
8. each unit s Installation i Guide H 16 1 2 li l 16 1 2 i i l No trim kit is required However 1 4 inch space needs to be Door Swing 4 Door Swing q P oor Swin i oor Swin Mei uy l i y hed y maintained between the units to ensure unobstructed door swing M Black White and Wood Overlay Stainless Steel Units must operate from separate properly grounded electrical 2175R F amp 2275WC Models receptacles placed according to each unit s Electrical Specifications Requirements Wall A Wall 1 4 Min gt lt B 2 Min gt fe P Power Su pply B ne The unit requires a grounded and polarized 115 VAC 60 Hz ISA circuit normal household current See Electrical Specifications t T ali lt J k Environmental Requirements H I I Ud I I am ii ee The units are designed to operate between 50 F 10 C and 100 F ii 1 2 DI 1 2 s A g0 A 37 C High ambient temperatures 100 F 37 C or higher may Door Swing MOI Door Swing MI i4 ili orf ir reduce the unit s abilitv to reach low temperatures and mav also ka 5 reduce the ice production rate for those models with icemakers Black and White Stainless Steel If the ambient temperature is expected to drop below 45 F 7 C 2175BEV drain all water from the unit to prevent freezing damage which is not covered by the warranty en Mae Wall ML Wall ie 2 Min
9. model s grille is designed to accept a wood grille overlay An overlay may be used to compliment a door overlay and provides a seamless look for your surrounding decor Follow the instructions below to prepare and install your grille overlay Be sure to read over this chapter completely before beginning Preparation The grille overlay MUST have venting as shown in the drawing below Failure to have proper venting can result in damage to your model The grille overlay may only be installed on indoor units I Prepare your overlay using the dimensions provided in the figure on page 15 for 24 inch models and page 16 for 15 inch models If using a hook and loop style mount drill hole A will not be used 2 If desired stain and finish your grille to match your surrounding decor Follow the stain manufacturers instructions to apply stain to your overlay Installation NOTICE The wood overlay grille must be installed in such a manner that the grille assembly can still be removed from the unit Screw Mount Recommended I Remove the grille from your unit by removing the two mounting screws See below Remove Screw Remove Screw 2 Lay the back of your grille overlay onto the front of the grille Make certain the screw holes and vents are aligned 3 Slide each of the screws removed in step through the grille overlay and grille 4 Mount your new overlay on
10. top hinge three screws 2 Reinstall hinge to bottom opposite I Install the hinge just removed from the top to the BOTTOM opposite side of the cabinet three screws 2 2 Remove the two door closer inserts 4 from the existing bottom hinge 3 Install door closer inserts as shown on the new bottom hinge 4 8 u line com Remove preexisting bottom hinge I Remove the preexisting bottom hinge three screws 2 Reinstall hinge to top opposite I Install the hinge just removed from the bottom to the TOP opposite side of the cabinet three screws 2 Reinstall Hole Plugs I Install plastic screw plugs three each top and bottom 3 into holes where hinge hardware was removed Prepare door for reinstallation I Remove plastic hole plug from top of door handle and reinstall on opposite side 2 With bottom of door facing up remove pivot plate 5 two screws 3 Hip over and install pivot plate on opposite side of door Ensure notch in plate faces center Install Door I Hold door upright and tilted forward Lift door on to bottom hinge closer inserts Tilt door forward into position Hold door to keep it from falling A Ww YN Reinstall hinge screw pin 1 into top hinge using a Phillips screwdriver Align and adjust the door Align and adjust the door see DOOR ALIGNMENT AND ADJUSTMENT on page 7 u line com Reversing Stainless Steel Glass Doors Remove Doo
11. 1 8 4 2175R C F Black and White Models 3 13 16 2175R C F S Overlay Models 2175BEVC Series 2175WCC Series 2275ZWC Series 2175BEVCOL Wood Overlay Models 2175WCCOL Wood Overlay Models 2275ZWCOL Wood Overlay Model Door Swing Dimensions 2175WC Models 21 15R Models ja Wall jee 2 Min gt e Wals Wall MW 1 4 Min l 2 Min gt ZI 21 A A ISSA 4 215 21 u u u 25 1 2 l 25 1 2 90 90 l i i Door Swing H Door Swing li e u u fil ni ALL wa l 4 iena Ma iaa Black White and Wood Overlay Stainless Steel I II 90 ii 90 E Door Swing Hi Door Swing i La v hard Y Black and White Models Stainless Models A N ikkes Units have a zero clearance for the door to open 90 Stainless 21 15WC Models Steel models require 2 1 8 door clearance to accommodate the handle if installed next to a wall Wall Wall NA A 1 4 Min gt 2 Min ij ma 7 7 Other Site Requirements Side Bv Side Installation 21 21 For a complete refreshment center install two units side by side Y i Cut out width for a side by side installation is the total of the A Ts 1 widths listed under Cut Out Dimensions in
12. Cutting Tools Drill amp Drill Bits Optional Door Panel on 21 5R F or 2175R F Black or White Models 1 4 thick door panel material Cutting Tools Obtional WC amp BEV Wood Trim Finishing Minwax Water Based Wood Stain Minwax Polycrylic Protective Finish Foam Applicator and or Synthetic Bristle Brush 220 grit Sandpaper 280 grit Sandpaper Obtional Overlay kits for Non OL models Model Panel Kit Black Panel Kit White 2115R U OL2115B U OL2115W 2175R U OL2175B U OL2175W 2175RF U OL2175B U OL2175W Exterior Cleaning Black and White Models Black and White surfaces may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Models Stainless door panels handles and frames can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach Keep your Stainless unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation Part numbers 173348 Do not clean with steel wool or abrasive pads Do not use cleaners that are not specifically intended for stainless steel on stainless surfaces this includes glass tile and count
13. INSTALLATION GUIDE 2000 SERIES GLASS DOOR REFRIGERATOR WINE CAPTAIN REFRIGERATORS REFRIGERATORS FREEZERS MODELS U 2175RCGOL 00 U 2175RFB 00 U 2115RB 00 U 2115WCOL 00 U 2175RCGS 00 U 2175RFS 00 U 2115RS 00 U 2115WCS 00 U 2175RCGS 01 U 2175RFS 01 U 2115RS 01 U 2115WCS 01 U 2175RFW 00 U 2115RS 02 U 2175WCCOL 00 U 21 ISRSOD 00 U 2175WCCOL 02 BEVE RAG E U 2115RSOD 01 U 2175WCCOL 60 CENTERS U 2115RW 00 U 2175WCCS 00 U 2175RCB 00 U 2175WCCS 01 U 2175RCB 02 U 2175WCCS 02 U 2175RCS 00 U 2175WCCS 13 U 2175RCS 01 U 2175WCCS 22 U 2175RCS 22 U 2275ZWCOL 00 U 2175RCW 00 U 2275ZWCS 00 U 2175RSOD 00 U 2275ZWCS 01 U 2175RSOD 01 U 2175BEVCOL 00 U 2175BEVCOL 02 U 2175BEVCOL 60 U 2175BEVCS 00 U 2175BEVCS 01 U 2175BEVCS 02 U 2175BEVCS 13 Table of Contents I Safety Precautions Safety Alert Definitions u Aa AAA nende tenen l General Precautions 2 Inspect amp Plan Product Registration Models Covered Tools Material Required a lie ade 2 Exterior Cleaning tienen neerde Meenen 2 Black and White Models 2 Stainless Models fii tet assets a aW La Banat alata anand 2 3 Prepare Site Electrical Specifications namen ee ne E S 3 C t O t Dimensions hesia e aa 3 2115 Series 2175 Series 2275 Series 4 Product Dimensions 2115R 2115WC OL amp 2175RC Series l u u 2175BEV 2175WC amp 2275ZWC Series 5 Door Swing Dimensions Other Site Requirements a a Nas 6 Side By
14. OL 00 YES U CLR2160B 40 YES U 2115WCS 00 YES U CLR2160S 00 NO U 2175BEVCOL 00 YES U CLR2160S 01 NO U 2175BEVCOL 02 YES U CLR21060S 40 NO U 2175BEVCOL 60 YES U CLR2160S 41 NO U 2175BEVCS 00 YES U CLR2160SOD 00 NO U 2175BEVCS 02 YES U CLR2160SOD 01 NO U 2175RCB 00 YES U CLR2160SOD 40 NO U 2175RCB 02 YES U CLR2160SOD 41 NO U 2175RCGOL 00 YES U CLR2160W 00 YES U 2175RCGS 00 YES U CLR2160W 40 YES U 2175RCS 00 NO U CLRCO2175B 00 YES U 2175RCS 01 NO U CLRCO2175B 40 YES U 2175RCS 22 NO U CLRCO3286S 00 NO U 2175RCW 00 YES U CLRCO2175S 01 NO U 2175RSOD 00 NO U CO2175FS 01 NO U 2175RSOD 01 NO U CO2175FW 00 YES U 2175WCCOL 00 YES Reversing Black or White Doors Remove Door I Hold door to keep it from falling 2 Remove hinge screw pin 1 from top hinge using a Phillips screwdriver 3 Remove door by tilting forward and lifting door off bottom hinge closer inserts 4 Reinstall hinge screw pin 1 into top hinge using a Phillips The hinge hardware will be removed and reinstalled on the screwdriver opposite side of the cabinet Remove hole plugs The top hinge hardware will be reinstalled on the bottom of the hike A Remove plastic screw plugs three each top and bottom 3 opposite side of the cabinet from new hinge location Save for reinstallation later Thebottom hinge hardware will be reinstalled on the top of the En opposite side of the cabinet Remove existing top hinge Remove existing
15. Stainless Frame I Prop frame against solid surface handle side down and away 2 Insert door logo forward into frame at a 30 angle For a right hand hinge the logo should be to your right For a left hand hinge the logo should be to your left Reinstall hinge to bottom opposite Door Orientation Right Hand Hinge I Install the hinge just removed from the top to the BOTTOM opposite side of the cabinet three screws 2 2 Remove the two door closer inserts 4 from the preexisting bottom hinge Logo Door Orientation Left Hand Hinge 3 Install door closer inserts as shown on the new bottom hinge Logo d 10 u line com Remove existing bottom hinge I Remove the existing bottom hinge three screws 2 Reinstall hinge to top opposite I Install the hinge just removed from the bottom to the TOP opposite side of the cabinet three screws 2 Reinstall Hole Plugs I Install plastic screw plugs three each top and bottom 3 into holes where hinge hardware was removed Install Door I Hold door upright and tilted forward Lift door on to bottom hinge closer inserts Tilt door forward into position Hold door to keep it from falling wu fk WN Reinstall hinge screw pin 1 into top hinge using a Phillips screwdriver Align and adjust the door
16. en track engagement on both sides gently push the rack into the cabinet until it stops Before reloading the rack ensure proper operation of the travel stops in the left and right track rails by pulling the rack out gently until it completely stops Staining and final finish application NOTICE DO NOT use oil based stains on wood trim Vapors from oil based stains will permanently penetrate the liner and will not dissipate over time Remove all screws securing wood trim to interior parts and remove the trim from the cabinet interior Lightly sand and clean wood Apply Minwax Water Based Wood Stain to wood with a synthetic bristle brush or a foam applicator Allow stain to penetrate about three minutes Before the stain is dry take a stain dampened rag and remove any excess stain remaining Wipe towards the grain with medium pressure to achieve the desired stain color After two hours repeat step 2 This will even out the color of the wood Allow stain to dry for a minimum of three hours before applying the final finish If desired sand the wood with very fine sandpaper to smooth the surface after staining Remove all dust from the wood and apply one coat of Minwax Polycrylic Protective Finish using a synthetic bristle brush to the wood Apply this finish in a thin coat following towards the grain Apply the finish to the back and sides of the wood first and allow it to dry for two hours Apply the finish to the fr
17. epth of the reveal is 1 4 on all four sides handle from door Pull handle up and off Slide custom door panel insert into 1 4 inch channel in door front NOTICE Use care not to damage magnet located on door bottom when installing door insert Do not set door on bottom edge when pushing insert into place NOTICE Raised panels will reduce the door s 90 swing zero clearance if the unit is installed next to a wall or similar type of structure 6 Panel Dimensions The door panel must not weigh more than 20 Ibs Model Width Height 2175R C F 23 1 32 27 11 16 2115R C F 14 1 32 27 11 16 Door Panel Installation Install the insert as follows Use care when handling the insert Insert edges may be sharp Remove top hinge screw pin with Phillips head screwdriver Remove door by tilting forward and lifting off bottom hinge pin Pull door gasket out of groove top edge of door only Start in the middle and pull outward moving toward the edge This may take some force u line com Holding door gasket out of the way replace handle on door making sure it is seated properly on insert and that screw holes line up Install two small screws removed in Step 3 Starting at the corners and working inward push door gasket into place on door Place door on bottom hinge pin and install upper hinge screw 9 Wood Grille Overlay Grille Overlay Your
18. er cleaners If any surface discolors or rust appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible u line com 3 Prepare Site Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for an electrical connection in the rear NOTICE Unit can NOT be installed behind a closed cabinet door Electrical Specifications SHOCK HAZARD Electrical Grounding Required Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit NOTICE Electrical installation must observe all state and local codes This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician The unit requires a grounded and polarized 115 VAC 60 Hz ISA power supply normal household current An individual properly grounded branch circuit or circ
19. m maintenance on the unit until the electricity has been disconnected Never remove the round grounding prong from the plug and never use a two prong grounding adapter Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty Never use an extension cord to connect power to the unit Always keep your working area dry Install provided Anti Tip kit Serious personal injury could occur Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges If your model requires defrosting DO NOT use an ice pick or other sharp instrument to help speed up defrosting These instruments can puncture the inner lining or damage the cooling unit DO NOT use any type of heater to defrost Using a heater to speed up defrosting can cause personal injury and damage to the inner lining NOTICE Do not lift unit by door handle Never install or operate the unit behind closed doors Be sure front grille is free of obstruction Obstructing free airflow can cause the unit to malfunction and will void the warranty Failure to clean the condenser every six months can cause the unit to malfunction This could void the warranty Allow unit temperature to stabilize for 24 hours before use Do not Block any internal Fans Use only genuine U Line replacement parts Imitation pa
20. n overlay frame covers the door frame to give a built in appearance Appropriate hardware and a copy of these instructions will be included with the unit NOTICE The thickness of the overlay panel must be 3 4 Right hand isometric view shown Opposite Use the following instructions to create or have a wood overlay panel created for you Wine Captain or beverage Center model as shown below Drill holes for pivot pins upper door hinge and lower door hinge as shown for left hand See Detail A i NOTE Final component is only a picture frame No panel inside of rails Excludes 60 Models NOTE Front view of wood panel with Dim right hand hinge shown mirror image for left hand hinge 2 1 4 AT Detail A Door top Scale 2 1 3 16 x 11 16 deep Detail C Door bottom Scale 2 1 3 8 x 1 4 deep Chamfer 1 32 x 45 3 4 1 1 ma Section A A Excludes 60 Models Dim A Scale 2 1 See Table Typ 4 places Dimension A Table u line com Dimension B Table EE L I Prepare the New Overlay Panel NOTICE The overlay door panel must not weigh more than 20 Ibs The thickness of the door panel must be 3 4 I Place a towel or similar soft non marking material out on a flat clean surface Be sure the material is large enough to have the wood panel not touch the hard mating su
21. ont side of the wood next and allow it to dry for two hours Sand with very fine 220 grit sandpaper Apply two morel coats of finish in the same manner but do not sand the trim after applying the final third coat Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior parts Final finish only application 5 Remove all screws securing wood trim to interior parts and remove the trim Lightly scruff sand the wood trim with 280 or finer grit sandpaper Remove sanding dust with a clean dry cloth The factory applied seal is compatible with almost all finishes A low odor water clean up quick drying finish such as Minwax Polycrylic Protective Finish is recommended Minwax Polycrylic is an ultra fast drying water based finish Apply a thin coat of a clear protective finish following the container label directions Lightly sand and reapply if desired Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior parts u line com 8 Door Panel Installation Remove the two outside screws holding door handle Slightly separate door Custom 1 4 Thick Door Panel Insert Door Panel Preparation A custom door panel may be inserted into the doorframe Custom door panels can be flat or raised as long as the maximum panel thickness where inserted into the door reveal channel is no more than 1 4 thick For raised panels the d
22. r ma 9 O s lt 2 I Hold door to keep it from falling 2 Remove hinge screw pin 1 from top hinge using a Phillips screwdriver 3 Remove door by tilting forward and lifting door off bottom hinge closer inserts 4 Reinstall hinge screw pin 1 into top hinge using a Phillips screwdriver Remove hole plugs I Remove plastic screw plugs from three each top and bottom 3 from new hinge location Save for reinstallation later Remove Stainless Frame I Remove two screws from top of door Save screws for later installation Top Of Door Screws U LINE 2 Remove pivot plate from bottom of door by removing 2 screws Set pivot plate and screws aside for later installation Bottom Of Door Pivot Plate 3 Grasp outer edge of stainless frame and firmly press inside edge 3 Swing door into frame of glass in while pulling stainless frame in opposite direction puma PP 4 Install screws removed in Remove Stainless Frame step to top of door opposite handle 5 Install pivot plat to bottom of door opposite of handle using hardware removed in Remove Stainless Frame step 2 Arrange 2 oa Pull Frame pivot plate so the flat edge is against the edge of the door Away Door Edge Pivot Plate Flat Edge Push Glass In Orient Hinge I Remove existing top hinge three screws 2 4 Unhinge frame from door Assemble
23. rface 2 Lay the wood panel out with the front side of the wood facing down 3 Cut the foam tape in to four pieces two pieces the width of the overlay and two pieces the height of the overlay 4 Remove adhesive protection strip from one piece of the cut foam and align the edge of the foam tape to the inside edge of the overlay as shown adhering the foam tape to the overlay See below _ Inside edge Front surface of overlav frame 5 Trim each piece of tape immediately after applying it to the overlay Do not allow any overlapping of the foam tape Damage to the overlay can occur is the foam tape is not trimmed correctly 6 If required attach any optional cabinet hardware to the wood panel at this time If an optional cabinet handle is installed make sure the mounting screw heads are below countersunk the back surface of the overlay Note After attaching the optional cabinet hardware additional supports may be needed to keep panel flat for next steps Attaching the Overlay Panel I Remove the top hinge pivot pin with a Phillips screwdriver and lift the door off bottom hinge pin Be careful not to lose the door closer insert sets Save pivot pin for use later See figure in next column 18 u line com Carefully lay the door over the wood panel making sure door is oriented correctly top of door with top of wood overlay Pull door gasket out of the groove completely Start in the middle and p
24. rts can damage the unit affect its operation or performance and may void the warranty 2 Inspect amp Plan L LINE Product Registration You have received a carton containing your U Line Refrigerator Refrigerator Freezer Beverage Center or Wine Captain unit with a package inside containing a Use and Care Guide a Product Registration Card and a water line kit Please complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the Use and Care Guide and this Installation Guide in a safe place for future reference Models Covered This installation guide covers the following models U 2115RB 00 U 2115RS 00 U 2115RS 01 U 2115RS 02 U 2115RSOD 00 U 2115RSOD 01 U 2115RW 00 U 2115WCOL 00 U 2115WCS 00 U 2115WCS 01 U 2175BEVCOL 00 U 2175BEVCOL 02 U 2175BEVCOL 60 U 2175BEVCS 00 U 2175BEVCS 01 U 2175BEVCS 02 U 2175BEVCS 13 U 2175RCB 00 U 2175RCB 02 U 2175RCS 22 U 2175RFS 00 U 2175RCGOL 00 U 2175RCGS 00 U 2175RCGS 01 U 2175RCS 00 U 2175RCS 01 U 2175RCW 00 U 2175RFB 00 U 2175RFS 01 U 2175RFW 00 U 2175RSOD 00 U 2175RSOD 01 U 2175WCCOL 00 U 2275WCCOL 02 U 2275WCCOL 60 U 2175WCCS 00 U 2175WCCS 01 U 2175WCCS 02 U 2175WCCS 13 U 2175WCCS 22 U 2275ZWCOL 00 U 2275ZWCS 00 U 2275ZWCS 01 Tools Material Required Screwdrivers slotted and Phillips head Models ending in OL Only 3 4 overlay frame material
25. s Drawer Models and Beverage Centers The U Line brand offers products in the 1000 Series 2000 Series and the Modular 3000 Series The 1000 Series offers a more targeted priced product with appropriate features while the 2000 Series offers upscale features advanced technology and specialized product families Our Modular 3000 Series provides sleek design and versatile temperature settings with our U Select control U Line s approach to its breadth of products multiple price points and features allows a choice and product that will fit any lifestyle DESIGNED ENGINEERED AND ASSEMBLED IN WISCONSIN USA
26. tallation procedures must be followed when completing an installation or relocation of a unit An INSTALLATION GUIDE for the unit providing complete installation information is available from U Line Corporation direct Consult the installation guide before any installation begins U Line contact information appears on the rear cover of this guide This unit requires connection to a dedicated 15 Amp grounded three prong polarized receptacle installed by a qualified electrician compliant with applicable electrical codes Safety Alert Definitions Throughout this guide are safety items labeled with a Danger Warning or Caution based on the risk type A DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death Warning means that failure to follow this safety statement could result in serious personal injury or death Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage u line com General Precautions Use this appliance for its intended purpose only Follow these general precautions with those listed throughout this guide A DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so children may not easily climb inside SHOCK HAZARD Electrical Grounding Required Never attempt to repair or perfor
27. to your unit by screwing the overlay back onto the base of your unit Hook and Loop Fastener Mount You may also mount your overlay to your grille using hook and loop type fasteners U Line recommends using 3M Dual lock fasteners To mount your overlay using a hook and loop fastener follow the instructions below I Read the instructions provided with your hook and loop fastener carefully 2 Apply hook and loop fastener system to the back of the overlay and front of the grille Use the shaded areas in the diagram below for application location 24 Inch Models Application Area Wood Overlay L C Back c 5 C I Grille T T Front LE gt 15 Inch Models Application Area Wood Overlay l Back Grille Front 3 Carefully align the wood overlay with the grille and press into position 14 u line com 8IL TT SJ POW YOU Z SUOISUSWIG LJJOAQ l5 15 u line com SJBPOW YDU S SUOISUSWIG efJ9AO l u line com 10 Overlay Frame Frame Preparation 2 2115WCOL 2175WCCOL amp 2175BEVCOL Models Only A
28. total unit rear height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening Installation I Plug in the powercord 2 Gently push the unit into position Be careful not to kink the water supply line or entangle the electrical cord 3 Re check the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop 4 Remove the tape from the glass shelves and wipe out the inside of the unit with a clean water dampened cloth Relocating the Shelves Both the glass shelves in the refrigerator and the inner door shelves can be moved to accommodate your bottles cans and containers Glass Shelves on Right Hand Hinge Units Open door fully grasp shelf firmly lift front edge slightly and pull straight out Choose new location and slide shelf onto the appropriate rib Glass Shelves on Left Hand Hinge Units Pull shelf out about 6 to clear the wall s molded protrusion e Tilt right hand edge of shelf up e Keeping at this angle and hugging the right wall pull the shelf out Choose new location and insert over ribs tilting right hand edge up Push in then lower shelf onto ribs Door Shelves First pull shelf up at
29. uit breaker is recommended GFCI ground fault circuit interrupter is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See below for recommended receptacle location Cut Out Dimensions 2115 Series Follow the cut out drawing The 15 1 4 width allows 1 4 for ease in installation and removal of the unit 24 is the cabinet depth in most installations t 35 g A 7 4 1 1 2 15 1 4 u line com 2175 Series Follow the cut out drawing The 24 1 4 width allows 1 4 for ease in installation and removal of the unit 24 is the cabinet depth in most installations 24 1 4 2275 Series Follow the cut out drawing The 24 1 4 width allows 1 4 for ease in installation and removal of the unit 24 is the cabinet depth in most installations MAN 5 fe LI 7 i 1 1 2 24 1 4 Product Dimensions 2115R Series 34 1 8 3 13 16 Fo 15 2115RS Stainless amp Outdoor Models 34 1 8 2115WC 21 15WCOL Series 2115WCOL Wood Overlay Models Not Including Wood Overlay Panel u line com 21175RC RCG RF Series 4
30. ull outward moving towards the corners see below This may take some force but be careful not to cut or rip the gasket After the gasket has been removed place it on a clean flat surface Secure the door to the back of the wood overlay using tape on all four corners Make sure all four edges are aligned See figure on next page Assembling Door to Cabinet DOOR FRAME 8 Starting at the corners and working toward the center push the door gasket back into place Make sure the gasket is fully seated on all four sides and corners 9 Check the closure assembly on the bottom hinge to be sure it is seated correctly in the bosses in the hinge TOP OF OVERLAY BOTTOM OF OVERLAY ULIN_0418_A 6 Use the door frame holes as a guide to drill pilot holes for the 6x1 pan head screws 6 x Pan Head Screws 10 Total Top Of Tape x x Al Door closers 10 Position door over closer Be sure the door hinge plate holes align with the bosses on the closer see below Failure to do so will result in the door not sitting in the proper position and door will not align correctly Sometimes it is helpful to open the door 180 to have the closer and pivot align correctly II Holding the door in the closed position install the pivot post through the top hinge into the top pivot plate Tighten securely with a Phillips screwdriver making sure post is seated fully
Download Pdf Manuals
Related Search