Toshiba IK-DF03A Security Camera User Manual
Contents
1. 1 Attach the alignment sticker to the surface 2 Drill one hole for cable at the center 3 Drill two pilot holes 7mmx40mm D through the two circles on the sticker 4 Hammer the supplied plastic anchors into the holes 5 Align the two holes on each side of the camera base with the two plastic anchors insert the supplied screws with camera to corresponding holes rere S NS z6 7 IN CASE OF PROBLEMS Condition Check Points No image e Are the camera and connected equipment turned on e Are wires connected correctly Unnatural color e Is the display monitor adjusted correctly e Is the lighting too dim Flicker noise e Under the fluorescent lamp of 60 Hz flicker noise rarely occurs 8 SPECIFICATIONS 1 Image System Image Device 1 3 inch CCD image sensor Pixel Elements 768 H x 492 V 2 Electrical TV System NTSC 2 1 Interlace 15 734 KHz horizontal 59 94 Hz vertical Horizontal Resolution 480 TV lines typical S N Ratio 48 dB Minimum Illumination 0 5 lux at 10 IRE Gain Control Auto AGC White Balance Auto White Balance Range 2 500 K to 9 500 K Electric Shutter 1 60 s to 1 100 000 s Backlight Compensation Always On Video Output Signal VBS 1 0 Vp p 75 ohms unbalanced BNC Synchronization System Synchronization System Internal Alignment Sticker Pan angle 350 75 Tilt angle 4 2 Adjusting the view2. 6 NOTES ON USE AND INSTALLATION e Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off e Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction e Treat the camera with care Do not drop the camera or subject it to intense vibration e Never touch internal parts Do not touch the internal parts of the camera other than the parts specified e Do not splash water on the camera Install the camera where the camera can be kept dry If the camera gets wet turn off the power and contact your dealer e Keep the camera installation away from video noise If cables are wired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment e Check the ambient temperature and humidity Avoid using the camera where the temperature is hotter or colder than the specified operating range Doing so could affect the internal parts or cause the image quality to deteriorate Special care is required to use the camera at high temperature and humidity e Should you notice any trouble If any trouble occurs while you are using the camera turn off the power and contact your dealer If you continue to use the camera when there is something wrong with it the trouble may get worse and an unpredictable problem may occur LIMITED WARRANTY CCD SECURITY CA
3. medical applications commercial aviation mass transit applications military applications homeland security applications nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage Accordingly Toshiba TAIS disclaims any and all liability arising out of the use of the product in any critical applications i 10 11 12 1 IMPORTANT SAFEGUARDS Read Instructions Read all the safety and operating instructions before operating the product Retain Instructions Retain the safety instructions and instruction manual for future reference 13 Lightning For additional protection on this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the video product due to lightning and power line surges If lightning occurs do not touch the unit Warnings or any connected cables in order to avoid electric shock Comply with all warnings on the product and in the 14 Overloading instruction manual Do not overload the power supply or extension cords as this Follow Instructions can result in a risk of fire or electric shock Follow all operating and use instructions 15 Object and Liquid Entry Cleaning Never push objects of any kind into this video product Disconn
4. BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND INCLUDING ANY DIRECT OR INDIRECT DAMAGES LOST PROFITS LOST SAVINGS OR OTHER SPECIAL INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES WHETHER FOR BREACH OF CONTRACT TORT OR OTHERWISE OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT EVEN IF TAIS ITS PARENT COMPANY OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE ABUSE ACCIDENT MPROPER INSTALLATION IMPROPER MAINTENANCE OR USE IN VIOLATION OF ISD S WRITTEN INSTRUCTIONS OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD S PRIOR AUTHORIZATION OR UPON THE REMOVAL OR ALTERATION OF ISD S FACTORY SERIAL NUMBER LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY No person agent distributor dealer authorized service provider or company is authorized to change modify or extend the terms of this Limited Warranty in any manner wha
5. angle 1 The lens pan direction can be adjusted by rotating the dome cover by hand Note e Do not rotate the dome over 350 otherwise the inner connector may break damaging the camera 2 Tilt angle of the lens can be adjusted within the limit of 0 to 75 by rotating Tilt ADJ screw with a compatible screw driver Note e Do not set up the lens at the limit position 75 of tilt angle otherwise the image of upper left and upper right may drop out 5 BACKLIGHT COMPENSATION BLC The BLC function of this camera is always ON The exposure is automatically adjusted so that the best picture is obtained at a monitor zone of about 75 in horizontal and about 75 in vertical direction a7 3 Mechanical Weight 0 729 Ibs 330g Dimension 3 97 D x 2 64 H inches 100mm D x 67mm H Pan and Tilt angle 350 Pan 75 Tilt Ingress Protection IP65 Rating 4 Optical Built in Lens f 3 6 mm F 2 0 View Angle of Lens 71 H 53 V 5 Power Input Voltage 12V DC 10 Current Consumption 0 16A 6 Environmental Operating Temperature 14 F to 122 F 10 C to 50 C and Humidity 20 to 90 RH Storage Temperature 4 F to 140 F 20 Cto 60 C and Humidity 90 RH Design and specifications are subject to change without notice 9 EXTERIOR VIEW 2 64 67 3 97 100 4 57 116 4 24 107 6 Dimensions Inch mm 10
6. MERA IK DF03A The Imaging System Division ISD of Toshiba America Information Systems Inc makes the following limited warranties with regard to this CCD Camera Model IK DFO3A Product These limited warranties extend to the Original End User You r Three 3 Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of three 3 years from the date of purchase by the Original End User During this three 3 year period ISD will repair or replace the Product if it does not perform as warranted In order to take advantage of this Limited Warranty You must a call 877 855 1349 to receive a RMA number and b pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center ISD reserves the right to substitute factory refurbished parts in place of those in need of repair Instruction Manual Owner s Manual You should read the Instruction Manual Owner s Manual thoroughly before operating this Product Before seeking warranty service you should check the troubleshooting guide in the Instruction Manual Owner s Manual and follow the instructions to correct the problem How to Obtain Warranty Service Step by step Procedures To obtain warranty service You should 1 Contact Toshiba at 877 855 1349 to first verify operation or installation assistance 877 855 1FIX 2 If technical support determines that
7. OISTURE The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance FIELD INSTALLATION MARKING WORDED THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES FCC USA INFORMATION NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party 2 PART NAMES AND FUNCTIONS Power Input Wire Connect the power cable to 12V DC Length approx 12 inches 300mm Do not touch this screw Video Wire BNC Tap Connect the video cable to a monit
8. TOSHIBA Leading Innovation gt gt gt DOME CAMERA IK DFO3A Please read this manual thoroughly before use and keep it handy for future reference INSTRUCTION MANUAL Record in space provided below the Model and the Serial as found on the label on the bottom of this unit Model IK DFO3A Retain this information for future reference Serial TABLE OF CONTENTS IMPORTANT SAFEGUARDS mociensrnsrniieiinn nrn A 1 A COMPONENTS ic isvsscssecsnsaesacveovarcatestestiacestistas E E 4 2 PART NAMES AND FUNCTIONS orssssssseseeseeseeseeseesccsecaecacesecseesecsecseeseeseeaeeas 5 5 _iGONNECTIONS onr ar ii Ee e N ERENT 5 A NSTAUA TT ON enaena n NE 6 5 BACKLIGHT COMPENSATION ceeroiriins isinsin E nE ttt ieee 7 6 NOTES ON USE AND INSTALLATION 8 7 IN CASE OF PROBLEMS crsssessessesseseeseees ne 8 SPECIFICATIONS s sscactesesedeecesceseeetevees E REREN EEEO NOR 9 6 EXTERIOR VIE iona o T 10 For information on our latest products and peripheral devices refer to the following Web page E hittp www toshibasecurity com The above URL is subject to change without prior notice If the URL changes refer to the Toshiba website http www toshiba com Disclaimer We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user in any of the following cases 1 Fire earthquake or any other act of God acts by third parties misuse by the user whether intentional or acci
9. aced upon or against or other hazards them Pay particular attention to cords at plugs screws and 19 Safety Check the point where they exit the product Upon completion of any service or repairs to this video Installation product ask the service technician to perform safety checks Install this video product on a secure part of the ceiling or to determine that the video product is in proper operating wall If installed on an unsecured location the camera condition could fall causing injury and damage ae 1 GAINS Rate sie ees owe sae nieee e eee E a e E e es e 1 2 Accessories a INSTFUCTION MANUAl eeeeeeeeeeceeeeeeeececeeeneceeeesceeaeeeeeeneeeeeneeenereeneaeaeneeeeeseee eee 1 b POWEYL CONNE CIOS eceeeteerteeteteceteeeeeeeneeeeneeeeeeeeeeaeeeneeneeeeeneeeneeeeneaeneneeeeeeeen eee 1 C SCrEWS ecco 2 d ANACHO EEEE EEE EEE E E EERS E RE REEE ENE E RANE RAEES 2 e Alignment Sticker Guide pattern ee E 1 CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightening flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR M
10. dental use under extreme operating conditions 2 Malfunction or non function resulting in indirect additional or consequential damages including but not limited to loss of expected income and suspension of business activities Incorrect use not in compliance with instructions in this instruction manual Malfunctions resulting from misconnection to other equipment Repairs or modifications made by the user or caused to be made by the user and carried out by an unauthorized third party Notwithstanding the foregoing Toshiba s liabilities shall not in any circumstances exceed the purchase price of the product Copyright and Right of Portrait There may be a conflict with the Copyright Law and other laws when a customer uses displays distributes or exhibits an image picked up by the camera without permission from the copyright holder Please also note that transfer of an image or file covered by copyright is restricted to use within the scope permitted by the Copyright Law O oR Protection of Personal Information Images taken by the camera that reveal the likeness of an individual person may be considered personal information To disclose exhibit or transmit those images over the internet or otherwise consent of the person may be required Usage Limitation The product is not designed for any critical applications Critical applications means life support systems exhaust or smoke extraction applications
11. ect this video product from the power supply before hrough openings as they may touch dangerous electrical cleaning points or short out parts that could result in a fire or electrical Attachments shock Never spill liquid of any kind on the video product Do not use attachments not recommended by the video 16 Servicing product manufacturer as they may cause hazards Do not attempt to service this video product yourself as Water and Moisture opening or removing covers may expose you to dangerous ea electrical or other hazards Refer all servicing to qualified Do not use this video product near water Some examples service personnel are near a bath tub wash bowl kitchen sink or laundry tub 6 in a wet basement or near a swimming pool 17 Damage Requiring service Accessories Disconnect this video product from the power supply and PRR refer servicing to qualified service personnel under the Do not place this video product on an unstable cart stand ollowin diti A 4 g conditions tipod bracket or table The video product may fall causing serious injury to a person or serious damage to the product a When the power supply cord or plug is damaged Use only with stand tripod bracket or table recommended b It liquid has been spilled or objects have fallen into the by the manufacturer or sold with the video product Any video product mounting of the product should follow the manufacturer s c If the video product has been exposed to rain
12. or or video device The image is outputted when powered on Length approx 12 inches 300mm Tilt ADJ screw i Turn this screw with a driver and adjust the angle of a video image Pan ADJ Turn this domed cover by hand and adjust the angle of a video image 3 CONNECTIONS Notes on connecting e Power plugs of connected equipment must be disconnected before camera installation e A 75 ohm coaxial cable with connector 8C 2V or 5C 2V is required for standard connection e For details of wiring and operation of equipment to be connected refer to their operation manuals e A power supply with cable connectors and coaxial cable are not supplied with the camera Display Monitor BNC Connector io ORed Connector avot 5 a power supply Bi GND Black t This Power connector is provided as an accessory Recommended power cord is a minimum wire size of 18 AWG Do not overload power supply The recommended power supply for this camera is 5 watts minimum at 12V DC 4 INSTALLATION Notes e This camera is for indoor application e The attached screws and anchors are used to install the camera to a solid surface e g concrete If installing to loose or thin material surfaces use the appropriate anchors not included with the screws e Install the camera firmly 4 1 Mounting the camera to a solid surface
13. or water instructions and should use a mounting accessory d If the video product does not operate normally by following recommended by the manufacturer he operating instructions in the instruction manual Adjust Ventilation only those controls that are covered by the instruction hae manual as an improper adjustment of other controls may This video product should never be placed near or over a result in damage and will often require extensive work by radiator or heat register If this product is placed in a built a qualified technician to restore the video product to its in installation verify that there is proper ventilation so that normal operation the camera temperature operates within the recommended e If the video product has been dropped or the cover has temperature range been damaged Power Sources f When the video product exhibits a distinct change in This video product should be operated only from the type of performance which indicates a need for service power source indicated on the information label If you are 18 Replacement Parts not sure of the type of power supply at your location consult When replacing parts be sure the service technician uses your product dealer parts specified by the manufacturer or have the same Power Cord Protection characteristics as the original part Power cords should be routed so that they are not likely to Unauthorized substitutions may result in fire electric shock be walked on or pinched by items pl
14. the unit is defective an RMA will be issued with return instructions for repair 3 Securely pack the Product in the original carton and external shipping pack include a letter explaining the problem with a copy of the bill of sale or proof of purchase 4 Prepay all transportation and insurance costs Your Responsibilities This Limited Warranty is subject to the following conditions 1 You must provide the bill of sale or proof of purchase at the time that warranty service is required 2 You must notify 877 855 1349 within 30 days after you discover that the product does not perform in accordance with specifications during the Limited Warranty period 3 You must pack the Product in its original carton using the original packing material Then insert the original carton containing the Product into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center DISCLAIMERS ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP
15. tsoever The time within which an action must be commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute or law of the United States or any state thereof is herby limited to one 1 year from the date You discovered or should have discovered the problem This limitation does not apply to implied warranties arising under state law Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law so the above provision may not apply to You This Limited Warranty gives You spacific legal rights and You may also have other rights which vary from state o state TOSHIBA TOSHIBA AMERICA INFORMATION SYSTEMS INC maging Systems Division e i
Download Pdf Manuals
Related Search