Home

Taylor C810 Wheelchair User Manual

1. GRILL TEMPERATURES Figure 26 PROGRAM At the end of the cook cycle the control will display DONE a tone will sound and the platen will automatically raise Item 1 Item 2 Item 3 Item 4 Item 5 Item DONE GRILL TEMPERATURES Figure 27 PROGRAM Note To cancel a cook cycle at any time press the RAISE button A tone will sound and the display will read CANCEL for five seconds and then enter an IDLE mode Models C810 amp C812 17 Operating Procedures Standby Procedures Whenever the grill is idle and product is not being cooked the upper platen must be placed in the STANDBY position Step 1 To place the upper platen in the STANDBY position press the STANDBY button twice from the open position Figure 28 The control will display GOING TO STANDBY and then change to display STANDBY Step 2 To raise the upper platen to the OPEN position to resume cooking press the RAISE button Figure 29 AN onnon Never use force to raise the upper platen Damage to components may result Only use the RAISE button to open the upper platen Menu Parameters To view the settings and actual temperatures for the current item press and hold the menu item key a minimum of 5 seconds The screen will display the cook time gap setting temperature set points and actual temperature readings of each zone for that menu item Item
2. Incorrect cooking time Reset the processor control for the correct time c Incorrect temperature setting c Adjust the processor control to the proper setting The upper platen or lower grill surface is not clean and or has carbon build up Closing procedures must be followed to properly clean the upper platen and the lower grill surface and to remove carbon build up The preset gap height is incorrect Call a service technician The heating zone is not heating The upper platen or lower grill surface is not clean and or has carbon build up Call a service technician Closing procedures must be followed to properly clean the upper platen and the lower grill surface and to remove carbon build up Release material sheet is worn Replace release material sheet c The platen is not level c Call a service technician The preset gap height is incorrect Call a service technician Air pressure is not high enough The thermocouple or the thermocouple interface board is faulty Defective motor control Defective stepper motor c Defective stepper motor wire harness Defective home switch Call a service technician Call a service technician Call a service technician Call a service technician c Call a service technician Call a service technician M
3. 696020 dL MO3HO 3ATVA 0z88 1dN 8101 HOLV1nIWnOOVOINV L Z04850 dO LXY L IH 331 coh zw lddv L X dL X 1d 000 zzocow 00092 5401881 NO 1H31 38n 1 os dHE AOvz JYNSSIYd HDLIMS so segzzo 2989W CIOSINVIN cor q s zuzeso 6 dO v 1Xv L ANEL IH ONILLLIJ oue dO 1247 1 IH HOLdVQV zz zuasezizeo cor z se 0 11 05 2 QOt SIA319 AYAS A0 c HIV HOSSdHdlNOOD 55019 MT1N SMYVINAY HHV kip lavd NOIIdIdOS Parts List 39 Models C810 amp C812 SMYVINAY ap 1 ise N 2 co ceo 882840 665840 S 0868 X 7162 0 28770 60l vZvEZ0 Y gt AS VLvVElX 888940 cVVvELO 280100 862Y20 1888 0 G 8Z 0 62496240 84957 8 6 0 So G9Z 0 oo SSV 19 MMT1N HHV d Jlavd w e 2180 Ws SV HO d IHS 9L SLXD L NI dVNS H3N31S VJ TT3IHS 3SV3H9 V LIM 89 TOHLNOO L33SV9 Nld HIO 4901 ALVW HOLOANNOOt IND OdINOO TIIYO FJYVMLOS LYMYIN N39 1OH1NOO 71 9 LIM gdO 1714 SSN 8 E HSHSVM 1N W OV d d dId1S MYW N39 6 XOd SV 1 1 HS dVO QV3H X3H LXIL B E MIYIS ALIS 8 EXZ6 0 HOS YIdIM 431 Zv80 JISVITIY LIFAS YINIVLIY V1 W TVIH 1VIA WD N 1VTd Z
4. The UNITS key is used to select either English or metric units of measure The UNITS key toggles between English or metric units with each key press ADJUST VOLUME Key The ADJUST VOLUME key displays the current volume To increase or decrease the volume use the UP and DOWN arrow keys MENU EDIT Key The MENU EDIT key is used to program a menu item When the MENU EDIT key is pressed the following screen will display Item 1 Item 2 Item 3 4 Item 5 Ne gt K Previous ious LOAD MENU FROM USB Figure 21 If there is more than one screen of menu items press the Previous or Next arrow keys to access the other menu items Press the menu item key to be programmed The following screen will display 13703 ACTIVE Delet ADJUST VOLUME ltem 1 YEs item TOP TEMP BOTTOM TEMP GAP 4257 3007 LAM 0 390 REMOVE IN 30 SECONDS ALARM AUTO SECONDS ALARM SECONDS ALARM T J Figure 20 Figure 22 Operating Procedures Models C810 amp C812 To edit a menu item press the menu item key to bring up a virtual keyboard Type in the desired name up to 8 characters per line and then press the X key to return to the previous screen Item 1 Figure 23 ACTIVE YES or
5. Failure to follow this instruction may result in serious electrical shock This grill must be installed on a level surface Failure to comply may result in personal injury or equipment damage Installation of Cable Kit If the unit is permanently connected the Cable Kit must be installed Flexible conduit must be used when installing the appliance Ventilation and Clearance To ensure proper operation of this appliance it must be installed so that the products of combustion are efficiently removed After set up do not store anything on top of the grill Failure to follow this instruction may result in a fire hazard Grease Disposal Container If the grill is not factory equipped with grease disposal containers the store is required to provide appropriate grease disposal containers in accordance with NSF Standard 4 requirements To the Installer Models C810 amp C812 Section 2 The grill you have purchased has been carefully engineered and manufactured to provide dependable operation This grill when properly operated and maintained will produce a consistent quality product Like all mechanical products it requires cleaning and maintenance A minimum amount of care and attention is necessary if the operating procedures in this manual are followed closely This Operator s Manual should be read before operating or performing any maintenance on your equipment It is strongly recommended that al
6. V HVH V HSV1dSMOVa dant t t X sswao aaWnN au nee 1HVd NOIIdIdHOS Parts List 31 Models C810 amp C812 1180 H3MOT V TOULNOD o BSINHOJSNVHL Le Moo EG OLEELO e o LW NF9 10H1NOD TiliS V Liy 33S F SMYVINAY co 05880 ggoeowdl zz zuasezize gu z 7 8 0 SSV1O ALO MT1N 0189 Jlavd 0189 A 0962 V G1 F3SNF YIUTOH 10 28 dINV 58006 aan aor EX LdWr F ONLLLEI LH39 OOdOO d TL TIA 9L SLXT L NI dVNS H N LSV AdAL 04 dITO YANALSVA 13315 VWE ONI Y 3 0182 ONIHIM INVHOVIG 9 9 NI9 HIV H3QNITAO FYIM t V0S A0Sc H3MOd QHOO CE80 N LV ld HHMOT H3AOOD HV8 3993 THU M 0180 N 1V 1d V AOO THYS 0185 YO LON TOYLNOD SMIYOS M LIWIT TOHLNOO avd HONOL TIIHO IOHLNOO dE MOAHO AA TWAT TdN 10L HOLVINNNDOV ANVLt v LXv L ANAL HH d X LdWt L X Lddv L 33 L qooseXaiesr NO dHE A0rz AYNSSAYd HOLIMS C 8 V q 1OdINVI 6 QO V LXY L ANAL IH DNILLIS dO v LXV L AYAS A0 c HIV HOSSdHdlNOD GHL 0c c L dOd SIA 1 90 Td 1LSVO OVd 390 TM TAAIMS S TIIHO H31SVO WALS 8 S 7 9 NOILdIH2S3G Models C810 amp
7. 9 4 NOLLNYO 03713 139v1 oso 94 8592 0 899640 OAS TIldS NdVA 14827 Old19 AYIM t NE ZHOS A00F JONVH4 LNVITdWOO SHOU 999670189 co 008620 Ovz 80Z 0Z1 VA001 SNVH1L cor 2 72698090 1109 Ov2 002 VOv dv Av 13H 01 72161860 1109 021101 VO b di AVT3U zaz 0180 MOSZ A082 V N 1VTd oo 899270 HLTV GOW 1198 NHVM 138V1 000 enAS669s 0 TLNI TANVd 1OH1NOO 138V1 01 6 97694220 2980 M 8 91 AOEZ 1SVO H 1V H eor 8829 0 asN3a1 quvno oo 299290 LYAZ WOOHOO H31 114 eor 1882 0 80 3104 Z HILIJ cor 0 TB LHA e980 V HALTS oo 46 0 018 ONIHIM NVHOVIG co 6 991570 1 S H ON 1099 LINIT IH TOULNOD 21419373 FYIM r NE ZHOS A00Y 1NVITaAOO SHOU 0009840182 SSV1O ALO MT1N 0189 Jlavd NOILdIH2S3G Parts List 37 Models C810 amp C812 2180 WALS 8 9 Z S d31SVO XdV9 ANI LHW N39 0180 NYO 1 0189 JISVIYO NVI dsNqrauvno GaJY YOLVYIIJJO NOLLNG dsNqrauvno 94 Ia HOLVHHdO NOLL8 X QI8 E L dVNS ONIHSH Q0O8 Z X dl 9L LL dVNS DNIHSN4 AFLMIO MeEXGIIZe9 S14 SNIHSrg V ASONTING HOLOW N3dd31S MAHOS dt 1VNIWNH319 0018 cok 779190 3avds sz dz 1TVNINH31 MOO18 cor ewe dl 1VNINEH31 MOO1T8 so 8 ge0ez20l
8. BOTTOM TOO COOL GRILL TE MPE RATU R E PROGRAM Figure 12 Figure 14 Operating Procedures 12 Models C810 amp C812 Item 1 Item 2 Item 3 Item 4 Item 5 Item 1 TOP TOO COOL GRILL TEMPERATURES 1669096 PROGRAM Figure 15 When the grill is at the proper temperature the temperature statements will no longer display and the temperature indicators will be illuminated in green Item 1 Item 2 Item 3 Item 4 Item 5 Item GRILL TEMPERATURES 9969 Figure 16 Programming Menu Items To enter the Program Mode the grill control must be in the OFF or IDLE mode Step 1 Press and hold the PROGRAM key for approximately five seconds to enter the Program Mode Item 1 Item 2 Item 3 Item 4 Item 5 Item GRILL TEMPERATURES Figure 17 PROGRAM Step 2 The PASSWORD screen will appear Enter the following password STORE Press the OK key STORE 1 Figure 18 Models C810 amp C812 Operating Procedures 3 The PROGRAM MODE screen will appear 13701 PROGRAM MODE Version GMX XX UNITS ENGLISH ADJUST VOLUME SERVICE CONTACT INFORMATION VIEW HELP Figure 19 UNITS Key
9. REMOVE IN 107 sec GAP 0 390 inches TOP SET POINT 425F BOTTOM SET POINT 300F ACTUAL TEMPERATURES TOP F 85F BOTTOM F 78F TOP R 85F BOTTOM M 80F BOTTOM R 73F Figure 30 If a key is not pressed for 20 seconds the grill control will return to the normal display Pressing the X key will bring the display back to the main display page Cleaning After Each Run of Product Step 1 Using the grill scraper scrape the grease on the lower grill surface from front to back Do not scrape across the rear of the lower grill surface with the grill scraper Figure 31 Operating Procedures Models C810 amp C812 Step 2 Use the wiper squeegee to clean the release material sheet on the upper platen Use a diagonal motion to clean the sheet Hold the handle at a slight upward angle with the wiper end facing downward Note Do not use excessive pressure when wiping the release material sheet with the squeegee Using excessive pressure can scratch or tear the release material sheet Figure 32 Step 3 Using the wiper squeegee push the grease at the rear of the lower grill surface into the grease can DO NOT use the grill scraper for this step Step 4 Use the grill cloth to clean the back splash plate and bullnose areas as needed during operation Note To increase the life of the release material sheet wipe it with a damp folded grill cloth a minimum of four times every hour CAUTION The up
10. and back of the platen surfaces Step 33 With a clean wet cloth rinse the platen cook surfaces Figure 49 Models C810 amp C812 Operating Procedures Step 34 C810 Press the STANDBY button to lower the center platen C812 Press the STANDBY button to lower one of the platens if needed Step 35 C810 With a clean wet cloth rinse both sides of the center platen Step 36 With a clean wet cloth rinse the inner edges of the right and left platens Step 37 Press the RAISE button to raise the lowered platen Step 38 With a clean wet cloth wipe the exterior of all the platens especially behind the rear of the upper platens next to the arm assembly Step 39 Starting at the back of the lower grill soread the remaining grill cleaner over the entire surface Do not scrub while applying product Step 40 Lightly scrub the surface with the non abrasive pad until all soil has been liquified by the grill cleaner Figure 50 Note The rear of the upper platen as well as the tubular arm can easily be wiped from the front of the unit If cleaning is performed on a daily basis there should be no carbon build up IMPORTANT the grill AN DO NOT use cold water or ice to cool the upper platen or the lower cook surface DO NOT use 8 jet of water to clean or rinse Failure to follow these instructions may result in N serious electrical shock burns fr
11. is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer The installation location is marked by the equipotential bonding symbol 5021 of IEC 60417 1 on both the removable panel and the equipment s frame A e Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all pole disconnecting device with a contact gap of at least 3 mm installed in the external installation e Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA particularly when disconnected or not used for long periods or during initial installation shall have protective devices such as a GFI to protect against the leakage of current installed by the authorized personnel to the local codes e Supply cords used with this unit shall be oil resistant sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer sheathed cord Code designation 60245 IEC 57 installed with the proper cord anchorage to relieve conductors from strain including twisting at the terminals and protect the insulation of the conductors from abrasion Installation This machine is designed for indoor use only 5 DO NOT install the machine in an area where a water jet could be used to clean or rinse the machine
12. power source must have an all pole disconnecting device with a contact gap of at least 3 mm installed in the external installation Safety e Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA particularly when disconnected or not used for long periods or during initial installation shall have protective devices such as a GFI to protect against the leakage of current installed by the authorized personnel to the local codes e Supply cords used with this unit shall be oil resistant sheathed flexible cable not lighter than ordinary polychloroprene or oth er equivalent synthetic elastomer sheathed cord Code designation 60245 IEC 57 in stalled with the proper cord anchorage to relieve conductors from strain including twisting at the terminals and protect the in sulation of the conductors from abrasion 3 IMPORTANT DO NOT use a water jet or spray excessive water on or anywhere near the grill Failure to follow this instruction may result in serious electrical shock and cause permanent electrical and mechanical damage to internal parts Failure to follow this instruction may result in A serious electrical shock E burns from hot steam A liquid collecting inside the grill and destroying electrical components Safety Models C810 8 C812 AN DO NOT use cold water or ice to cool the upper platen or the lower cook surface Failure to follow
13. this instruction may result in A serious electrical shock burns from hot steam A liquid collecting inside the grill and destroying electrical components 3 Failure to follow the instructions below may result in severe burns from high temperatures DO NOT prepare or remove product without proper equipment DO NOT allow untrained personnel to operate this grill USE EXTREME CAUTION when cleaning the grill 3 Appropriate grill clearance must be maintained from all combustible materials Failure to comply could result in a fire hazard A Take caution to protect eyes lungs and all parts of the body from potential harm when using any chemical cleaner Failure to follow this instruction may result in a chemical burn A DO NOT use any abrasives or cleaners other than approved food service cleaners and degreasers Failure to comply may cause illness to the consumer and may also damage grill surfaces This grill must be installed on a level surface Failure to comply may result in personal injury or equipment damage The grill must be pulled away from the wall for thorough cleaning Disconnect the tether to the grill located on the back panel of the unit When returning the grill to its original position use extreme caution to smoothly and slowly roll the grill backward into place Failure to do so may cause the grill to tip and will cause severe equipment damage or personal injury es
14. 0 69GELX 57950 OdaINOOINOod we 000 9 1 9 col 9 00 eu Ln i div v eor e r ali G96CLX 7 LEGELZX LGGGLZX OcL EEZGS0O LVZELO 8 G 0 6ESLZO TIIHO V 1V Id Y AONIH HOOd V 1V Id TASNIH dOOd V 31 ld GW8Ix SNIddS NId THDId 01850 HHMO T 3GIS7 THNVd 133140180 HHMO T 3GIS7 THNVd 6180 HHMOT LNOHJ THNVd HJMO TMOV87T3NVd l1H S 8 c 8 Hdddf dIS V TANVd L1 S5 8 GES Y9IddN 3GIS V THNVd 0180 LHOITV TANVd 01109 15 931 TANVd JOIAH3S 948 7 TANVd MEOL X GO9L L ONIY O 2001 8 TA ZIHM 04 L X 91 9 HAC INOHS MAYHOS EA dd 1S SE GEN HV3JO HOLOIN 2189 0180 YAIJdO NVIN ISd 021 0 JINSSITYd YOLV NOJY LNW MOVE LIN 8 L ISd 051 1 gL dO t LMOETI T3AIMS ONILLIA gL dO t t MOETI T3AIMS ONILLIA 06 QO Y LXY L dWAL IH ONILLIA LdW 9ISNJYIA ONILLIJ 39I3HO 0 0 MTIOJINVWN HDO 18 V Q IOJINVIN NOILQVO O313 T38VT 9LGIXLNIdVNS d N LSV ssvo Alo MT1N HuVM 0189 Jlavd NOILdIH2S3G Models C810 amp C812 34 Parts List 0189 00 9 2 920 982 dd SNIHdS NId ONIMASNALVId 000 z 7920 280 HOLVT NOISN31X3 SNIHdS 000 ve 0 6588 0 QL SLXb
15. 0189 HOSSHdlNOO HIV VIG WW ZL SWH 2OVAOS8c HOLSIHVA G IO3INVIN OGA ZL AVM GIONTIOS 3NTIVA G IO3INVIN ISd 0 4411389 TVA HOSSHdlNOO HIV dE MOAHO AATWA cc OIdIdO 69 M MOAHO AN TVA 0OL AOBET Xdl0S AAE ASOH 0 QGO9L Z X IT SGVYEOTAN SENl 0OL AOBET Xdl0S AAE ASOH ZLEOEY QGO9L Z X IT JAVY9BOTAN JAENL 0OL AOBET Xdl0S AAE ASOH 0 QGO9L Z X IT JAVY9AOTAN JAENL HHIN 9 LUZ 3SOH dIAV 1O 100L qO8EY XGdl0Sc A38 HSOH goose x GIOZL JFJENL 5 LHOIY 018 HINHOO WIHL 9 1431 0180 YINYOD NI DI so Ovz 802 02 VAOOL SNVHL Nalvid eol 01 SS 3dAL Y FINOJONYIHL co 6 eu SEN FZZW Y Td1OOOWd HL HOSS ddWOOgly sok zeseso 3811 QOL X dO1 X QOv I 331 HOSS ddWOOglv cok 2 2120 1d X X Lddv 1 331 ozeezo LdN 8101 HOLVINNNIIV ANVL HOLIMS HOLY1 sor 08 9 0 TVNINYIL MIYIS HILIMS cor aregee0 G9dl d AVOL LSdQ H33908 HO1IMS HO1OW d dd 1S 26 6 0 HOLIMS JWOH YOLVNLOV Hdld uv3o col e bb620 1SdS NOLLNGHSNd HOLIMS uv vuossaudwoo cor 2 6 8 70 3 18 00 5 FTUNSSIYd HILIMS SSV IO ALO MT1N SMYVINAY 0189 Jlavd NOILdlH2S3G e o eo N S a e e Models C810 amp C812 36 Parts List SMYVINAY 0189 000 D4 r8rSZ0
16. 130 YolIYLIG 2 AZL w m Az te Juin 183 dol ya tO GIN T ut 401 LI Fi bo GIN on aH x8 pe 1d Q an Te HLH yg 9 9
17. 2 8 5 0018 HOLIMSTOHINOO sor 9 sovo ON LOVLNOO 49078 00 8 2prozzo 91 91 X v JONVILONIYYIB 0980 N NY 413S dl v NIHV 2 Q Sri620 dV QV3H X3H LXIL 8 E MIYIS 000 2 9 99000 1713 SSN 8 E H3HSVM EGET T N IQ r dS 99820 91 71 1 21 11 AT138 uvg 6 8 0 1951 Xv LXzE 0 YJAaINOHS MAYOS i c C Sime 1TNyOO 39NV14 ZIHM 2 01 LON HSAOONALWid sor 2 WIHALVW asvatay v 00 998 2180 v HSV TdSyIOVd eo 2 899290 3811 GO 7 1 X LdWt l HOLdVdV sswoo aaWnN SMYVINAY HuVM apa Jlavd NOILdlH2S3G Models C810 amp C812 38 Parts List 2180 gg e 72490 1OUINOO LISVO 980 V ATOJINVW 969570 LNW 4098 LAW 8 1 ISd 0EL 39nvo A 096 V SI 3aSnd4 u3q1OH H v 10 28 dINV 06 aan JOr LXLadWY L ONILLII LH39 WODQYOO YILII ae X 18 1HM AZZ v 114 000 vz 62t8 0 9U SLXt L NI dVNS H N LSV oo 8 82 0 3dAL N 02 diTO YANJLSVA 13318 6 DNIH 189 ONIYIM WVYOVIA 9 0 34OULS NI9 BIV H NI1AO FYIM V0S A0Sz H3MOd QHOO 280 N31V1d H3MOT H3AOO 3SV3T3U M 0180 N31V 1d V H3AOO H80 H3MOT VJ1OHINOO TIYO 0189 HOLOW 1OH1NOO NalW1d rn ze SM3HOS M LINIT TOULNOD 1yHW N3OTIOULNOO 7199 9 118 BS8 fo w dYd HONOL TilHO 10H1NOO so
18. 908 B EXOZ H L MAYIS so z Have 1H5IH N3lv1d A3TInd oo z 96966 13S 133908 8 EX02 v M3HOS z rezen 1431 Nalvid AdTInd ee9220 318VO N1V dA TInd 55019 MT1N SMYVINAY HHV d lavd NOILdIH2S3G Models C810 amp C812 42 Parts List SMYVINAY 2 180 HOSS3HdWOOHIV sor 2 9 00 0 VIG WW L SINH OVAO8Z HOLSIHVA QIOJNVW 01 56920 OQA ZL AVM ION TOS ATVA eor 756920 ISd OZ 431734 JYNSSIYd JATVA HOSS ddWOOgly sok 696020 dL MO3HO 3ATVA z ee ZZN OIHIHO 69 M 0 HO ATVA 00055 X AIOZL JENL THDId 01850 HANYOO WIYL 1431 0180 YINYOD NI DI Idd 0 6 806 0 VAOOL SNVH L NalW1d 01 SS 3dAL dnOOOWH HL so 6 Se99x SEN F3ZZN IIANODONYIHL YOSSFYaNOD uly esor zeseso 3811 QOL X qOt X qOt 331 YOSSFYaNOD uly esor Zzwe 1ddt 1 X dL X Lddv 1 331 cor 0288 0 LdN 810L YOLVINNNOOV ANVL HOLIMS HO V 08 620 Ssv19 MT1N HHV kip Jlavd NOIIdIdHOS Parts List 43 Models C810 amp C812 Koun 41013105 QV iun 01013305 a Holl 01013305 NU 3m IN3 ume enn IW3 4 V3 ISI NT VIS ye 0 We He LI HOLY TT i 00 09 YOL
19. C812 32 Parts List SMYVINAY wo s nen so 6oivwe zz e mas yezx ee9o00 889570 eyye20 z 000 6 eeeyeol zeee20 9 e 00 5 zieoedl EE 092670 N G 2782 9 Q1OJINVIN 9692 0 55019 MT1N 0o Jlavd 0189 00 IN ASWAYOD CTAIHS SV HOD Y LIM 790 TOHLNOO L33SV9 Nid HID MOO1 ALVW HOLOANNOOt WD OdINOO T1ldS9 3HVA LdOS LYYW N39 1OH1NOO 79 9 9 LM gdO 1714 SSN 8 E H3HSVM 1N W OV d d dId1S LIN NID 6 XO9 SV 1 HS dVO QV3H X3H LXIL B E MIYIS ALIS 8 EXZ6 0L HOS YIdIM NO T43 1L H3dVHOS 2080 3SVd 3H L33HS H3NIV LHH V1 W TVIH 1VIA N39 dV9 NIAHOSS OOV Y LIM VO NIVHLS3H LJ V LIM 001L dQO8 t XGl0SZ A38 3SOH 802 MO06L 1SVO H3 1V3H LLE OL89 TOULNODO HONOL SSINYVH 0182 HOLIMS SSANYVH 2080 O I OL SS SS NHVH 8 HOLIMS YO FDd SSINYVH T SE ZEN HOd HO LOW V SS3NHVH 2080 8 L d NOO V SSINUVH 2080 3A TVA dlNOO V SS NdVH N31VT1d 310NVH LAWN N39 ld ALLVd 3GIn9 GW8Ix IOULNOO LAMSVD INW MOVE LIN 8 1 ISd 051 1 NOILdlH2S3G Parts List 33 Models C810 amp C812 SMYVINAY we 02 EG GLGELX 0189 01850 A802 0096 V N3 LV Id 0052
20. HOSS OOV V LIM VO NIVHLS3H LJ V LIM 802 MO06L 1SVO H3 1V3H LE OL82 TOULNODO HONOL SSINYVH 0182 HOLIMS SSINUVH 0882 O I OL SS SS NHVH 2080 O I OL SS SS NHVH Z 80 HOLIMS dD Od SS NHVH 189 9789 HOSS ddAOO SS NHVH 2180 JAYA dAOO V SS3NHVH GE ZEWs HOd HOLOW V SSINYVH 299 JAYA dINOO V SS3NHVH JAYA diWOO V SS3NHVH N31V1d 310NVH NOILdlH2S3G Models C810 amp C812 40 Parts List SMYVINAY ET TOULNOD LNOtid LESELX 0ZL 66 ZGO 55019 MT1N HHV d lavd 2180 94 Ia VIG 8 E L 3 IOH OfY 1d VIC WE L JTOH ON ld 01850 A802 M009c V N3 LV ld H HO5NIH HOOGF V 31V Id TASNIH HOOG V ld GW8Ix dIddN ONIHdS Nld IH9OIY 01850 HHMO T 3GIS7 THNVd 133140180 JAMO T 3GIS7 THNVd 6180 HHMOT LNOHJ THNVd HJMO TMOV87T3NVd l1H S 8 c 8 Hdddf dIS V 1 NVd 1 1S 8 c 8 H3ddfl dIS V TANVd anogHS H3lN3O V TANVd OIAd S MOV8 V TANVd MEOL X GO9L L DNIY O 20201 14 ZIHM 04 L X 9 9 YITINOHS MIYISTt EA dd 1S SE GEN HV3JO HOLOIN 2189 0180 YAIJO NVIN OGA ZL AVM ION 1OS ATVA ISd 0 1 d 1SS dd ATVA ISd 021 0 JINSSITYd YOLV INOJY LNW MOVE LAN 8 1 ISd 051 1 gL dO t L AO813 T3AIMS ONILLIA gL dO t L AO813 T3AIMS ONI LLIA LdW v L 9ISNJIYIA ONILLIJ dI
21. IPTION PART NO CASTER 5 7 5 8 STEM 078377 CASTER GRILL 5 SWIVEL LOC 073240 PANEL FRONT LOWER 073650 15 CONTROL A SWITCH X73659 INCLUDES ITEMS 15a 15e GENERAL MARKET NOTE 1 KIT PER PLATEN 101006 Operator Parts Identification 6 Models C810 C812 C816 C818 C812 Exploded View DESCRIPTION DESCRIPTION PART NO CAN GREASE 073294 PANEL SIDE LOWER RIGHT 073261 SLIDE GREASE CAN 073293 CASTER 5 7 5 8 STEM 078377 PANEL SIDE LOWER LEFT 073262 W LOCK PANEL A SIDE UPPER LEFT _ X72962 CASTER GRILL 5 SWIVEL 073240 PLATEN A 2600W 208V X73272 23 PANEL FRONT LOWER 073650 7 PANEL A BACK SERVICE X72951 15b BUTTON OPERATOR RED 076011 PANEL BACK LOWER 073432 CONTROL A SWITCH X73659 8 SCREW 10 32X3 8 SLTD TRUS 024298 BUTTON OPERATOR BLACK 076012 9 KITA GREASE SHIELD X78330 SER SWITCH ROCKER DPST 10A 076989 WP PANEL A SIDE UPPER RIGHT X72965 KITA ORIEL CONTROE MISSES OE Models C810 amp C812 7 Operator Parts Identification Accessories Figure 3 DESCRIPTION PART NO SHEET RELEASE BOX 9 073442 2 RETAINER SHEET RELEASE 072845 RETENTION BAR 3 CLIP RELEASE MATERIAL 072673 W TAB SCRAPER TEFLON WIPER 075887 110207 DESCRIPTION PART NO STRIP REPLACEMENT 075888 6 HOLDER CLEANING 073736 PAD CLEANING 073737 CLEANER STERA SHEEN 6 073160 1 QT CS SHOWN PER PLATEN SHOWN PER PLATEN NOTE EXT
22. L NI dVNS H3N3LSV4 H S 0868ZX 1 IHS 3SV3HO V 14 9 8 0 e W SV dS d IHS 01 z vev ZLEE 318n00 anouHs e segx 280 N 1VTd V anouHs 6 trezo H3NNI 3811 1V d q IHS 6 zero 3811 1Vd q IHS 6 9 1nO qnOHHS 1V d q1 IHS 6 sevo qnOdHS 1V d q IHS 9 828 0 ZZ W SV HO 1 IHS 9 4z6z20 SNITanOO qT IHS ee ee ee 1NOU4 ONMaNOD QTAIHS HSviasmovamtuy ooo 9 620 SE ZEN WHV Tv3S oo o 660007 dINOONN 5 1 XIL FYOD LNVIVIS cor 9 6200 L X 91 9 cor e 88850 208 9976405 HICINOHS MAHOS cor ez 0020 v L EXB E HIATNOHS MIYOS 01 9 es 19561 20 1228 01 YIATNOHS MIYIS eo st 20012570 A 072 WHVTV NON SS AV13H 980 V GIOIINVN ISd 051 0 SHNSSAYd HOLWINOAY LIS OOS 8 82406 60L u 8vc 40 LHSIY NALW1d ASTINd 00 969680 13S 1 YOOS B EXOZ H L MIYOS e revzeso 1331TN31V1d A3TInd 9 zeezol 318v9 N 1V d A Tnd z 996050 lLSV 1d 40918 VIG 8 6 1OH 5n d 000 l L9gESO MOVIE VIG 8 6 ITOH DMId Ssv19 MT1N SMYVINAY HuVM 0162 Jlavd NOILdlH2S3G e Parts List 35 Models C810 8 C812
23. NO This key displays the current selection Pressing the key toggles to the opposite selection Selecting YES will display the menu item on the main display screen TOP TEMP This key displays the current set point temperature for the platen To increase or decrease the temperature use the UP and DOWN arrow keys BOTTOM TEMP This key displays the current set point temperature for the lower grill surface To increase or decrease the temperature use the UP and DOWN arrow keys Note When setting the temperatures for a given item the limits are 150 F to 450 F 66 C to 232 C for the upper platen and 150 F to 400 F 66 C to 204 C for the lower grill surface If the temperatures are set lower or higher than the temperature limits the set point at the control will default to 150 F and 450 F 66 C and 232 C respectively CLAM FLAT This key displays the current setting CLAM or FLAT associated with that function Pressing the key toggles the mode to the opposite selection GAP This key is only active if CLAM has been selected The key displays the platen gap in inches or mm associated with the function To increase or decrease the gap setting use the UP and DOWN arrow keys MULTIPLE TIMING FUNCTIONS There is one timing function for clam menu items and a maximum of three timing functions for each flat menu item Each function has a set of parameters associated with it The function currently associated with the me
24. ON TOULNOD a 0 08 3 YOLOW TOYLNOD 39198 180815 Houn H21V1 EL EU E a asivy m AHONYIS e 38176 ER Aa0NVIS Yu Taine Tim fine m Bu ys Ra 6 a a ayvon e AV1dSIQ 1081 03 lr quyog AV1dS10 10ULNOD quvog e AV 14510 TOULNOJ a a G e 8SS a a a a 381 ow 1891 LL nd 3653 n 1991 NOOK mr rana zz 1881 36881 UNE ena V 11711 802 WI NEO Tak Wie 115 OIA quvog YOLON TOYLNOD s e CO o 073370 23 9 14 10 n IWI 4 In LINES 201831 1 L fa mum AzL LY4 dol HIH dol GIN dlH 11 x8 y co or Loo ane ONT zoo GTON3TOS WV HOLY 01903199 NJ Koun 41913105 WY HOLYT 4800 NIY Tara ET EEEE 381 8 ABONY1S 11 AQONVLS HOLWT ANyIS Thu T
25. RA CLIPS ARE SENT WITH GRILL Operator Parts Identification Models C810 amp C812 Section 5 Important To the Operator F e b e e 3 9 zg 1 EE 2 3 item 4 9 5 OFF 4 CLEAN 8 Previou Next GRILL TEMPERATURES EN PROGRAM 6 7 5 Figure 4 DESCRIPTION DESCRIPTION RAISE BUTTON 6 TEMPERATURE INDICATOR LIGHTS 2 STANDBY COOK MODE BUTTON POWER KEY 4 CLEAN MODE KEY 9 MENU SELECT KEYS 5 PROGRAM KEY EA Dec Models C810 amp C812 9 Important To the Operator Section 6 Operating Procedures The Model C810 has three independent upper platens The Model C812 has two independent upper platens These grills are capable of cooking a variety of products and feature two cooking options They provide all of the features of a flat grill as well as the advantages of two sided cooking Note The three platen Model C810 has been selected to illustrate the step by step procedures For grills equipped with less than three platens perform the following steps as appropriate for your grill platen configuration Daily Opening Procedures Before operating the grill the release material sheets must be installed on the upper platens Perform the following steps for installing release material sheets CAUTION Make sure the grill is COOL before attempti
26. UI Tanu Tun rT ET TI ym EI TW TW TAN Yu Jr Yu 0 08 YOLON 1081 02 0 08 YOLON 1OYLNOD Ja mix 11719510 TOYLNOD AVIdSIQ TOU LNOD lr qawog 10510 TOYLNOD ELI tou eset an OVA 007 IVA 007 t Mi Wo FO 183 401 6 YLH dOl IS ate te un LI m V IIV110 CN T co C os 38 o 9 15 10 41013105 OY Ho11 01913109 N amr IN3 4 wm ae kn l III ITI wie im 1 DTI PE quvog T D03181 YOLOW 1081NOD A Ju FE HO1V1 L T TT CTT gf 0 8 YO LON 1081N02 31 8 MR ABGNYIS 5 H21V1 luf Tii luna CT 8108 TE mann AHONYIS voi 351 8 190115 r ine A Tina ym mun 00 8 e AW1dS1d TOYLNOD mix mix AV dS10 0HIN0 Ir qawoa AV dS10 TOULNOJ YU ier RETE Yu I Cum rasa dd ht1 me 6 4 9 0 98 an A 802 A 808 1Iv
27. YLS DMV 06 v80 NId NId HIO v 4001 ALVIN YOLOANNOO V Q IOJINVIN NOILdlH2S3G Parts List 41 Models C810 amp C812 2180 sot dW686970 S9dl d AVOL LSdQ H331908 HOLIMS HO1OW d dd 1S eor 2 2660 HOLIMS JWOH YOLVNLOV Hald dv3D cor 2 sye20 1SdS NOLLn8HShd HO LIMS uiv vHOoss3HdWOO eor Q 9O6 840 dH A0bz JYNSSIYd HILIMS 00 25792 0 2780 H3ddh ONIHdS NId ONIHdS NALVId 000 8 7 20 280 HO1V1NOISN31X3 ONIHdS so z 8 0 ZIEL N 318n0d anouus 2 Ste8zx 2780 N31vd v ONOUHS 9 rwa H3NNI 3811 31V1d G13IHS 9 zozo 3811 31 19 013 15 9 99220 31 19 013 18 9 9220 GNOUHS 31V1d G13IHS 000 vz 6 2590 9U SLXt L NI dVNS H N LSV H S 0868ZX 1 IHS 3SV3HO V 14 8 8 0 e W SV dS d IHS 46220 ONNaNOIJ aTAIHS z 926z0 1NOH 5NI1dnOo TIHS HSVTdSOV WdV ooo 29560 SE ZEW WHV 1V3S 00 u 660001 dWOONN v L X31 3809 1NV1V3S so 6 0 L X 94 5 HAGINOHS MAYOS cor 8 186890 20S 9975 40 b b EX8 E 1OHS A HOS 1951 207 122 0 H TnOHS A HOS Solo A 075 WHVTV NON SS V ee ISd 021 0 AHNSSAYd HOLVINDAY 000 z 96966 13S 133
28. all possible hazards to the user and the equipment have been addressed Electrical Connections The grill is supplied with two power cords Check the data plate on the grill for voltage cycle phase and electrical specifications Refer to the wiring diagram provided inside the protective control panel door at the front of the grill for proper power connections The power connection is located behind the access line cover on the front of the grill In the United States this equipment is intended to be installed in accordance with the National Electrical Code NEC ANSI NFPA 70 1987 The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity This code contains provisions considered necessary for safety Compliance therewith and proper maintenance will result in an installation essentially free from hazard In all other areas of the world equipment should be installed in accordance with the existing local codes Please contact your local authorities The Proper Wire Size and Branch Circuit Overcurrent Device shall be selected according to the data label information and in accordance with CEC Part 2006 Section 14 100 e i FOLLOW YOUR LOCAL ELECTRICAL CODES Models C810 amp C812 To the Installer CAUTION THIS EQUIPMENT MUST BE PROPERLY GROUNDED FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK v unit
29. e all warning labels that have been attached to the grill to further point out safety precautions to the operator This piece of equipment is made in America and has American sizes on hardware All metric conversions are approximate and vary in size NOISE LEVEL Airborne noise emission does not exceed 70 dB A when measured at a distance of 1 0 meter from the surface of the machine and at a height of 1 6 meters from the floor These instructions are valid only if the country code symbol appears on the appliance If the symbol does not appear on the appliance refer to the technical instructions which give the necessary instructions for adapting the appliance to the utilization conditions of that country x 4 the crossed out wheeled bin symbol is affixed to this product it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13 2005 Therefore it must be collected separately after its use is completed and cannot be disposed as unsorted municipal waste The user is responsible for returning the product to the appropriate collection facility as specified by your local code For additional information regarding applicable local laws please contact the municipal facility and or local distributor Models C810 amp C812 Safety Section 4 Operator Parts Identification C810 Exploded View Figure 1 DESCRIPTION PART NO DESCR
30. face board is faulty c Call a service technician Call a service technician The solid state relay is faulty The restaurant circuit breaker has been tripped Call a service technician Reset the circuit breaker The control cord is not connected properly Reconnect the cord c The fuse in the control box is faulty c Call a service technician The power switch is faulty Incorrect use of the STANDBY button Call a service technician Press the STANDBY button within five seconds of lowering the platen into the COOK position Faulty wire connections Call a service technician Models C810 amp C812 27 Troubleshooting Guide PROBLEM 6 The upper platen will not stay in the COOK or STANDBY position 7 The upper platen will not stay in the COOK position but will stay in the STANDBY mode 8 The upper platen opens too rapidly 9 The display reads PLATEN NOT LATCHED 10 The display reads UPPER PLATEN STUCK 11 The platen will not lower to preset gap height PROBABLE CAUSE Temperature is insufficient to satisfy the indicator LED s REMEDY Wait until the indicator LED s turn green The control harness is faulty Call a service technician c The interface board is faulty c Call a service technician The latch switch is faulty Call a service tec
31. hnician The latch solenoid is faulty Call a service technician The processor control is faulty Call a service technician The pneumatic system is faulty The processor control is not set properly The orifice check valve is incorrect or missing The pneumatic system is faulty Call a service technician Call a service technician Call a service technician Call a service technician The latch switch is faulty Call a service technician c The latch solenoid is faulty The arm bearings are dirty c Call a service technician Call a service technician The air cylinder is faulty Call a service technician c Plugged air lines to cylinders Defective motors and cables c Call a service technician Call a service technician Defective motor interface board Call a service technician c Loose harness connections c Call a service technician Defective main display controller Call a service technician Troubleshooting Guide 28 Models C810 amp C812 PROBLEM 12 The product is under cooked or overcooked 13 The product is not cooking evenly 14 The display reads PROBE OPEN 15 The display reads HOME SWITCH STUCK ON PROBABLE CAUSE The release material sheet is worn REMEDY Replace the release material sheet
32. ial clip the release sheet Scrape the lower grill surface with the grill scraper retainer and the release material sheet Take these from front to back parts to the sink to be washed and rinsed Figure 40 Step 11 Use the wiper squeegee to push residual grease Figure 38 into the grease cans Step 7 Repeat steps 1 through 6 for the remaining upper platen s Step 8 Wash and rinse the clips and retainers in the sink Set them aside for future use Step 9 Set the release material sheets aside on a clean flat surface next to the sink until further cleaning is performed DO NOT fold crease or place them on sharp objects Figure 41 Step 12 Remove empty and reinstall the grease cans Figure 39 Figure 42 Models C810 amp C812 21 Operating Procedures Step 13 Step 17 Using an approved high temperature grill cleaner Apply grill cleaner to the platen surfaces pour approximately 3 oz 90 ml onto each 12 305 mm cook zone p NN Figure 43 Figure 45 Step 14 Firmly attach a non abrasive pad to the pad holder Step 18 Note The pad must not contain any ceramic Apply grill cleaner to the back side of the upper particles platens Step 15 Dip the non abrasive pad into the grill cleaner IMPORTANT DO NOT SCRUB while applying grill cleaner in the following steps Step 16 Apply grill cleaner to the front side of the upper platens Figure 46 Step 19 Apply grill clea
33. ility and or local distributor Models C810 amp C812 To the Operator Section 3 We at Taylor Company are concerned about the safety of the operator when he or she comes in contact with the grill and its parts Taylor has gone to extreme efforts to design and manufacture built in safety features to protect both you and the service technician As an example warning labels have been attached to the grill to further point out safety precautions to the operator AN IMPORTANT Failure to adhere to the following safety precautions may result in severe personal injury or death Failure to comply with these warnings may damage the machine and its components Component damage will result in part replacement expense and service repair expense To Operate Safely 1 DO NOT operate the grill without reading this Operator s Manual This manual should be kept in a safe place for future reference A Failure to follow the instructions below may result in severe injury or death from electrocution DO NOT operate the grill unless it is properly grounded DO NOT attempt any repairs unless the power supply to the grill has been disconnected must be performed by an authorized service technician DO NOT operate the grill unless all service panels are restrained with screws e Stationary appliances which are not equipped with a power cord and a plug or other device to disconnect the appliance from the
34. l personnel responsible for the equipment s operation and cleaning review these procedures for proper training and assurance that no misunderstandings exist In the event you should require technical assistance please contact your local authorized Taylor Distributor Note Warranty is valid only if the parts are authorized Taylor parts purchased from an authorized Taylor Distributor and the required service work is provided by an authorized Taylor service technician Taylor reserves the right to deny warranty claims on equipment or parts if non approved parts or refrigerant were installed in the machine system modifications were performed beyond factory recommendations or it is determined that the failure was caused by neglect or abuse To the Operator Note Constant research results in steady improvements therefore information in this manual is subject to change without notice x mamam the crossed out wheeled bin symbol is affixed to this product it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13 2005 Therefore it must be collected separately after its use is completed and cannot be disposed as unsorted municipal waste The user is responsible for returning the product to the appropriate collection facility as specified by your local code For additional information regarding applicable local laws please contact the municipal fac
35. material sheets on a clean sanitized flat surface to air dry overnight Figure 54 Models C810 amp C812 25 Operating Procedures Non 24 Hour Stores Only Step 51 Leave the upper platens in the OPEN position Step 48 overnight Wipe all areas with a clean wet cloth Step 49 Step 52 Wipe all exterior panels Place the power switch in the OFF position Step 50 Apply a light coat of vegetable oil to the entire lower grill plate Figure 55 Figure 56 Operating Procedures 26 Models C810 amp C812 Section 7 Troubleshooting Guide PROBLEM One side of the grill will not heat The control will display the message FAULTY ELEMENT OR SHORTED PROBE after the TOO COOL timer has elapsed One heat zone will not heat The display reads TOO COOL One of the heat zones is overheating The display reads TOO HOT The grill will not turn on when power switch is placed in the ON position The upper platen will not stay in the STANDBY mode but will stay in the COOK position PROBABLE CAUSE The heater is faulty REMEDY Call a service technician The high limit switch is faulty Call a service technician c The solid state relay is faulty The interface board is faulty c Call a service technician Call a service technician The solid state relay is faulty Call a service technician c The control harness is faulty The inter
36. ner to the outer edges of the right and left platens Figure 44 Step 20 C810 Press the STANDBY button to lower the N center platen DO NOT use metal scrapers abrasive pads screens or wire brushes Damage to C812 Press the STANDBY button to lower one of components may result the platens if needed 110204 Operating Procedures 22 Models C810 amp C812 Step 21 C810 Apply grill cleaner to both sides of the center platen Step 22 Apply grill cleaner to the inner edges of the right and left platens Step 23 Press the RAISE button to raise the lowered platen Step 24 Lightly scrub the front side of the platens with the non abrasive pad until all soil has been liquified by the grill cleaner For stubborn soils apply additional grill cleaner and lightly scrub Do not rinse the platens at this time Step 25 Lightly scrub the platen surfaces S mi Ta Figure 47 Step 26 Lightly scrub the back side of the upper platens Figure 48 Step 27 Lightly scrub the outer edges of the right and left platens Step 28 C810 Press the STANDBY button to lower the center platen C812 Press the STANDBY button to lower one of the platens if needed Step 29 C810 Lightly scrub both sides of the center platen Step 30 Lightly scrub the inner edges of the right and left platens Step 31 Press the RAISE button to raise the lowered platen Step 32 With a clean wet cloth rinse the front sides
37. ng to install or remove release material sheets Step 1 Slide the release sheet retainer through the hemmed end of the release material sheet Figure 5 Step 2 Hook the release sheet retainer on the release material shoulder screws at the top of the upper platen Figure 6 Step 3 Hold the non hemmed end of the release material sheet Gently pull the sheet tight wrapping it around the platen in a side to side manner Figure 7 Note Check the alignment of the release material and make sure it fits smoothly over the upper platen Operating Procedures Models C810 8 C812 Step 4 Place the release material clips over the release material sheet Press them into place over the release material bar at the top of the platen Figure 8 Step 5 Check the tightness of the release material against the upper platen Figure 9 Note Installing the release material sheets too tightly may cause premature failure of the sheet Step 6 Repeat steps 1 through 5 for the remaining upper platens Note It is not necessary to change the release material if small pin holes develop Note Rotate and reverse the release the material sheets on a daily basis The release material must be changed when Product sticks to the release material Carbon builds up causing problems in taste or appearance There is a tear in the release material in the cooking area 14361 P Figure 10 The
38. ntification 6 C810 Exploded VieW esie Vue wets See ese iG e EE e See ee eae ins 6 C812 Exploded View Soopers canoe Maree bore eee vean oo tae a dac 7 ACGESSONIOS 2 8 Models C810 amp C812 Table of Contents Table of Contents Page 2 Section 5 Important To the Operator 9 Section 6 Operating Procedures 10 Daily Opening Procedures 10 Operating Procedures 17 Daily Cleaning Procegures os korido refi abi ki 19 Section 7 Troubleshooting Guide 27 Section 8 uu 25 31 44 Wiring DiagramSs ere sd siu uus pur REND E me og momo EE SERE TAN Note Continuing research results in steady improvements therefore information in this manual is subject to change without notice September 2010 Taylor All rights reserved 073523 M TAYLOR reise A aylor Company The word Taylor and the Crown design are registered trademarks in the United States 750 N Blackhawk Blvd Rockton IL 61072 of America and certain other countries Table of Contents Models C810 amp C812 Section 1 The following are general installation instructions For complete installation details please see the checkout card Installer Safety A In all areas of the world eq
39. nu item is displayed Pressing either function 1 function 2 or function 3 will bring up the next function in the list The functions provided are REMOVE IN TURN IN SEAR IN ALARM AUTO MANUAL This key displays the current status of the alarm mode Pressing the key toggles the mode to the opposite selection IF ALARM AUTO is selected the alarm will automatically stop after five seconds has elapsed If ALARM MANUAL is selected the operator must touch either the display screen the raise button or the standby button to stop the alarm XXX SECONDS This key displays the time associated with that menu item in seconds To increase or decrease the seconds setting use the UP and DOWN arrow keys Upon completion of all programming selections save the selections by pressing the OK key To return to the main display screen without saving the programming selections press the X key SERVICE CONTACT INFORMATION Key Press the SERVICE CONTACT INFORMATION key to view the programmed service contact information SERVICE CONTACT INFO NAME Service Company PHONE XXX XXX XXX EMAIL XXXXXXX QXXXXXXX COM Figure 24 VIEW HELP Key The View Help key is not functional at this time future development Models C810 amp C812 15 Operating Procedures Patty Placement Placement procedures of meat products must be Note It is very important that all patties be followed on the grill The meat must be placed on
40. odels C810 amp C812 29 Troubleshooting Guide PROBLEM 16 The display reads HOME SWITCH NOT SEEN PROBABLE CAUSE Defective motor control Defective stepper motor c Defective stepper motor wire harness Defective home switch Broken platen cable REMEDY a Call a service technician b Call a service technician c Call a service technician Call a service technician Call a service technician Troubleshooting Guide 30 Models C810 amp C812 Parts List Section 8 SXiqvnwnIJy e HOLOW d dd 1S L9 e 899250 HOLIMSTOHLNOO sor 9 60940 000 a m 2 oo cres 0189 XdVO ANI LHW N39 L00393H9 QUVO 0180 NYO 1 0180 JISVIYO NVI ASNITTAYVNO AaJY YOLVYIIJJO NOLLNG dsNqrqaavno 94 Ia HOLVHHdO NOLL8 X QI8 E L dVNS ONIHSH Q0O8 Z X dl 94 LE dVNS DNIHSN4 JLO MeEXGIIZe9 S14 SNIHSrg V ASONTING TOAld 1 OVH N33H9 dZ TVNINYIL ADOT19 439 MAYOS dv IWNINYAL MOO1E VdS SZ d IWNIWYAL MOO1E ve 8 E LSNCAV dv5100 1H ON LOVLNOO MOO 18 91 91 X ADNV1A ONIYVAE NOMV 35 0 t ONIYVAE dVO QV3H X3H LX91 8 MdqHOS 11 SSN 8 E HHHSVM 1 ATISG YVE 1921 Xb LX e Ol IMOHS MAIYIS LANMDIOT TA ZIHM 2 0L LON SV 1
41. om hot steam A liquid collecting inside the grill and destroying electrical components damaged cook surfaces Step 41 Carefully pour warm water on the lower grill surface starting from the back to the front Use the squeegee to remove the cleaner from the grill surface NN Figure 51 Operating Procedures 24 Models C810 amp C812 Step 46 Remove and empty the grease cans To avoid damaging the grill Never use grill screens on the upper platen or the lower grill surface e Never use any abrasives or cleaners other than the approved cleaner e Never allow the grill scraper or the abrasive cleaning materials to come in contact with the release material Step 42 Pour a small amount of lukewarm water on a clean wet cloth over the bottom grill surface and wipe off the residue Figure 53 Step 47 Wash rinse and reinstall the grease cans 24 Hour Stores Only Step 48 Re install the release material sheets on the opposite side than previously used Secure the sheets with the release material clips and retainers Start up the grill per instructions starting on page 10 Figure 52 Step 43 Wipe the lower grill surface with a clean wet cloth Repeat until no visible soil remains Step 44 On aclean sanitized flat surface next to the sink clean both sides of the release material sheets by gently wiping them with a clean sanitized cloth Step 45 Place the release
42. per platen surface is very HOT To prevent burn injuries use extreme caution when wiping the release material sheet Daily Cleaning Procedures Note The three platen Model C810 has been selected to illustrate the step by step procedures For grills equipped with less than three platens perform the following steps as appropriate for your grill platen configuration Step 1 Raise the upper platen to the OPEN position by pressing the red RAISE button Figure 33 AN nor Never use force to raise the upper platen Damage to components may result Only use the RAISE button to open the upper platen Models C810 amp C812 Operating Procedures 2 Press the CLEAN key When the cook surfaces reach the proper temperature for cleaning an alarm will sound and the message READY TO CLEAN will be displayed Item 1 Item 2 Item 3 4 Item 5 Ready to Clean GRILL TEMPERATURES Figure 34 PROGRAM Step 3 Press the RAISE button to cancel the alarm Figure 35 Step 4 Put on heat resistant gloves Figure 36 S CAUTION The upper platen surface and release material sheets are very hot To prevent burn injuries use extreme care Step 5 Wipe the exposed surface of the release material sheets with a clean wet cloth Figure 37 Operating Procedures Models C810 amp C812 Step 6 Step 10 Remove the release mater
43. release material substance is worn from the release material sheet Note Temperature checks should only be conducted with the release material sheets removed Note Rotate and reverse the release material sheets on a daily basis Models C810 amp C812 Operating Procedures Care of Release Material Sheets The control will display the word INITIALIZATION for five seconds and then will enter the OFF mode displaying the message OFF The temperature DO NOT fold or crease indicators will not be illuminated A tone will sound for 20 seconds unless the operator touches either the display screen the raise button or the standby button Item 1 Item 2 Item 3 Item 4 Item 5 OFF Figure 11 GRILL TEMPERATURES DO NOT touch with any sharp object or abrasive PROGRAM DO NOT hose with hot water or soak in water DO NOT place under other objects Figure 13 Step 2 Touch a menu key on the control to start the grill The grill will start heating up to the proper Start Up of the Grill temperature The control will display the selected menu item and indicate BOTTOM TOO COOL and IMPORTANT The lower grill surface and the TOP TOO COOL The grill temperature indicators upper platen MUST BE CLEAN before starting will be illuminated in amber these procedures Step 1 Place the power switch in the ON position Item 1 Item 2 Item 3 Item 4 Item 5 Item 1
44. removed from the lower grill surface in the same the lower grill surface from front to back When the sequence that they were placed before cooking cook cycle is complete the upper platen will raise Patties must be removed immediately after the upper platen has been raised to the OPEN position and after the meat has been seasoned 1 Patty 2 Patties 3 Patties 4 Patties 9 9 0 1 2 5 Patties 6 Patties 8 Patties 4 SO maximum of 6 maximum of 8 4 oz patties 1 6 oz patties Patties are generally placed two at a time from front to back of grill and right to left The removal order of the patties is shown in the diagrams by the number shown in the center of each patty Operating Procedures 16 Models C810 8 C812 Operating Procedures Cooking Product Step 1 Select the menu item to be cooked The grill is at the correct temperature if the control does not display any temperature statements and the grill temperature indicators are green Step 2 Quickly place the product on the lower grill surface from front to back Step 3 Press the STANDBY button once Figure 25 The display reads MOVING DOWN as the platen lowers to the cook surface During the cooking cycle the display will show the name of the current menu item REMOVE IN and the time remaining until the product should be removed Item 1 Item 2 Item 3 Item 4 Item REMOVE IN 106 SECONDS
45. uipment should be installed in accordance with existing local codes Please contact your local authorities if you have any questions Care should be taken to ensure that all basic safety practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment Only Taylor authorized service personnel should perform installation and repairs on the equipment e Authorized service personnel should consult OSHA Standard 29CFRI910 147 or the applicable code of the local area for the industry standards on lockout tagout procedures before beginning any installation or repairs e Authorized service personnel must ensure that the proper PPE is available and worn when required during installation and service e Authorized service personnel must remove all metal jewelry rings and watches before working on electrical equipment AN The main power supply s to the equipment must be disconnected prior to performing any repairs Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous moving parts as well as poor performance or damage to the equipment Note All repairs must be performed by an authorized Taylor Service Technician To the Installer This unit has many sharp edges that can cause severe injuries Site Preparation Review the area where the unit will be installed before uncrating the unit Make sure
46. y I Models C810 amp C812 Auto Lift Grills Operating Instructions 073523 M TAYLOR 9 15 10 Complete this page for quick reference when service is required Taylor Distributor Address Phone Service Parts Date of Installation Information found on data plate Model Number Serial Number Electrical Specs Voltage Phase Maximum Fuse Size Minimum Wire Ampacity Part Number September 2010 Taylor All rights reserved 073523 M TAYLOR The word Taylor and the Crown design are registered trademarks in the United States of America and certain other countries Cycle Amps Amps Taylor Company 750 N Blackhawk Blvd Rockton IL 61072 J J J Ban _ 7 T able of Contents Section 1 To the Installer 1 Installer Sal OLY END Sie Preparations uma Osee D apte phu umapa ao pated 1 Electrical Connections 1 Installation i255 4e dn LE eng 2 Gk oe ns he DIE sa muna n Lei ns T EE Le 2 Installation of Cable Kit III 2 Ventilation and Clearance 2 Grease Disposal Container 2 Section 2 To the Operator LiL 3 Section 3 Salely le tet ex one tee ones 4 Section 4 Operator Parts Ide

Taylor C810 Wheelchair User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents