SV Sound SVS PB2-ISD Speaker User Manual
Contents
1. only one supplied to the Monitor Out connector Connect the other end of the RCA cable to your TV or Security Monitor s Video In socket Turn on the mains power to the 2Volt power supply a and follow the instructions in the operation section below on the following pages If you have an A V TV with RCA sockets you will need to switch the TV to the AV channel to view the quad processor To view the quad processor connected to your VCR you will need to select the AV input you have connect the quad processor to on the VCR turn your TV onto the channel you would normally use to view a tape or movie on your VCR This channel may be activated by a button on your remote that is marked with this symbol GF or LI or L2 or possibly AVI or Av2 VCR VCR MONITOR MAINS IN OUT OUT DC 12V WALL SOCKET O00 a a ai b eu a ji CAMERA S i BNC to RCA cable CAM1 CAM2 CAM3 CAM4 Please note Only one BNC to RCA cable for connecting the Quad Processor to your TV VCR or AV Monitor is supplied Please see your local electronics retailer for information on purchasing additional suitable cables Operation Front Panel ZOOM CH1 CH2 CH3 CH4 ENTER FREEZE MENU POWER Geta QQQQQQQO Color Quad Processor ae gt AUTO a Oo Please refer to the panel diagram above for additio2. Help Desk Support Details Swann Technical Support All Countries E mail tech swann com au Telephone Helpdesk UNITED STATES toll free 877 274 3695 Sun Thurs 2pm 10 30pm PST 800 627 2799 Mon Fri 9am pm PST USA Exchange amp Repairs 562 777 255 Mon Fri 9am 5pm PST AUSTRALIA toll free 1300 13 8324 Mon Fri Jam 5 30pm Aus EST International 61 3 8412 4610 Mon Fri Jam 5 30pm Aus EST See http www worldtimeserver com for information on different time zones and the time in Melbourne Australia compare to your local time Warranty Information Swann Communications warrants this product against defects in workmanship and material for a period of one 1 year from it s original purchase date You must present your receipt as proof of date of purchase for warranty validation Any unit which proves defective during the stated period will be repaired without charge for parts or labour or replaced at the sole discretion of Swann The repair or replacement will be warranted for either ninety days or the remainder of the original one year warranty period whichever is longer The end user is responsible for all freight charges incurred to send the product to Swann s repair centres The end user is responsible for all shipping costs incurred when shipping from and to any country other than the country of origin The warranty does not cover any incidental accidental or consequential damages arising from the use of or the inability to
3. W x D 1 29 x 5 7 x 4 72 inches 33 x 145 x 120 mm Weight 0 88 pounds 400 grams Ports Camera In x 4 BNC Female VCR In x BNC Female VCR Out x BNC Female Monitor Out x BNC Female FCC Notice We Swann Communications of 106 12 Shoemaker Avenue Bldg A Santa Fe Springs CA 90670 USA declare under our sole responsibility that the product SW247 QP4 This product meets the requirements specified in Part 15 of FCC Regulation Operation rests with the following two conditions 1 The equipment should not cause any harmful interference 2 The equipment must receive and process any interference including any possible interference caused by operation mistakes After testing the product we confirm that it complies with the provision for class C digital equipment in the 5th part in FCC regulation and the receiver complies with the limitations for class B digital equipment in Part 15 of FCC regulation The product generates applies and emits radio waves It might cause harmful interferences to wireless communication if not be installed and used following the description of the manual The product may cause interference in residential area and the customer should take remedies to eliminate the interference at their own costs If the product causes any harmful interference to wireless equipment or disturbs the receiving of TV signals it can be identified by turning on and off the product you can solve the trouble by following m
4. creen Brightness Contrast Saturation Hue Sharpness Change the settings for the image produced by the selected camera Mirroring Flip the image horizontally text will appear reversed Motion Setup Camera Select the camera that you are going to modify the settings on Detection Time Set the operating time for motion detection Sensitivity Velocity Set the amount and speed of movement to trigger event Masking Area Select the area of the image to be monitored for movement Event Setup Buzzer Report Control Set whether the buzzer activates for these events Buzzer Hold Time Set the duration of the beeper sound for each event Report Hold Time Set the time the camera remains on screen after an alarm Alarm Polarity Set for input polarity of alarm connected to alarm port Not used on this model Event Report x 6 PAGE Select page of event report to view List Clear Clear entire list of event reports Simple Connection Instructions Please refer to the connection and panel diagrams below and over the page for more information Connect the cable from the DC 2Volt power supply a to the DC 2Volt socket b on the rear of the unit Connect your cameras to the Video In sockets CAMI CAM4 on the rear panel of the unit If your camera has RCA male plugs you will first need to fit the supplied BNC to RCA adaptors to the Video In sockets and connect your camera s to each of these Connect the BNC to RCA Cable c
5. ee the recorded footage play on your TV or Monitor Press any of the channel Buttons to show that channel in full screen mode 5 Freeze Auto Button Press this button for less than second to Freeze the current image on screen Press for longer than second to start automatically switching between Quad Screen and Individual camera views Press the button for less than second twice to turn Auto Mode off or press the Menu Button to return to the normal view 6 Menu Button Press this button for less than second to change back to quad screen mode from any other display mode Press for longer than second to enter and exit the configuration menu Operation Rear Panel iei VCR MONITOR CAM1 CAM2 CAM3 CAM4 OUT OUT DC 12V 8 g 9 7 Channel 2 3 and 4 Video Input Sockets Connect the BNC to RCA adaptor to each socket to which you will connect a camera that uses a Male RCA plug on the end of it s cable If you are using a camera that comes with a cable that uses BNC connectors then you do not need to use the BNC to RCA adaptor for that camera socket 8 VCR In Socket Plug the Video Out socket of your VCR into this socket to allow you to view individual cameras in Full Screen mode when playing recorded footage back 9 VCR Out Socket Plug the Video In socket of your VCR into this socket to allow you to record footage to your VCR while you view the Quad Screen on your monito
6. ethods 1 Re adjust the product or put it in another place 2 Extend the distance between the equipment interfered and the product and 3 Refer to dealers or experienced radio electrician for help CE Notice This product complies with standards including Low Voltage Device Directive 73 23 EEC EMC Directive 89 336 EEC and R amp TTE Directive 1999 5 EC It passed the subject tests by the authority concerned and is authorized to bear CE mark Q System Setup Use the up down buttons to highlight the setting you wish to change then use the left and right buttons to change the setting Date Adjust the date format and set the date Time Adjust the current time in 24hour format military time System Format Set the TV signal to be PAL or NTSC Default is set to TV standard of country of sale System ID Number Feature not used Key Lock Lock all Buttons except Menu Button Factory Reset Reset all settings to Factory Default Display Setup Display on Screen Place a tick to display each of these Title Date Time Screen Position Move the image on your screen left or right Border Color Change the color of the border between the screens Auto Sequence Page A Set the length of time in seconds the screen pauses Page B Set all cameras to SKIP Not used on this model Camera Setup Camera Select the camera that you are going to modify the settings on Title Change the name of the camera on the main s
7. home or business at once Simply connect up to four security cameras to the Swann Quad Processor and view them on any AM TV VCR or Swann security monitor and you can keep an eye on all the important areas from one central location Choose between a quad screen 4 cameras at once split screen picture in picture or see each camera view individually in full screen The Swann Quad Processor also features an auto switch function allowing you to scan between all camera views including the split screen with a user definable pause on each screen Your Color Quad package comes with e x Color Quad Processor x 2Volt Power Adaptor design may vary between countries 5 x BNC Male to RCA Female adaptors x IR Remote Control x Video Cable e This Instruction Sheet fany of these items are missing please contact your retailer FCC NOTICE This device complies with Part 15 of FCC Rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received Including interference that may cause undesired operation Ss Technical Specifications Refresh Rate NTSC 60frames sec PAL 50 frames sec Resolution NTSC 720 x 480 PAL 720 x 576 Video System PAL or NTSC switchable Video Input 1 0Vp p 75 ohms Video Output OVp p 75 ohms Power Source 2Volt Operation Temperature 14 F 122 F 10 C 50 C Dimensions H x
8. nal information 1 Power Switch Press to turn the unit on 2 Zoom Mode Button Press this button for less than second to switch through the different screen modes 8 screens 2 x Picture in Picture x Picture in Picture Split Screen When in Picture in Picture or Split Screen mode press the Enter Button to enable configuration mode Once in configuration mode press the Up and Down buttons to select one of the channels you are viewing then press the Left or Right button to make changes You can change which camera appears in which box and also where the PiP boxes appear on the screen Press the Enter button again to save your settings when you have finished To enter amp exit the ZOOM mode press this button for longer than second Once in configuration use the UP DOWN amp LEFT RIGHT buttons to move the zoom box then press ENTER button to view zoomed area 3 Channel 2 3 and 4 Left Right Down and up Buttons Press the Channel Buttons to view each camera independently in full screen mode Use the UP Down buttons to navigate the Configuration Menu and the Left Right buttons to change the highlighted setting 4 Enter PB Button Press this button for longer than sec to switch to VCR Playback mode To use VCR Playback mode effectively you must have a cable connected from your VCRs Video Out to the VCR In Socket 8 and the VCRs Video In to the VCR Out Socket While in VCR Playback mode press Play on your VCR to s
9. r 10 Monitor Out Socket Plug the Video In socket of your TV or Security Monitor into this socket to allow you to view the video signal generated by the Quad Processor 11 12Volt DC Power Socket Connect the supplied Power Adaptor to this socket to power the Quad Processor Use of Power Sources other than the one supplied will void your warranty
10. use this product Any costs associated with the fitting or removal of this product by a tradesman or other person or any other costs associated with its use are the responsibility of the end user This warranty applies to the original purchaser of the product only and is not transferrable to any third party Unauthorised end user or third party modifications to any component or evidence of misuse or abuse of the device will render all warranties void Swann www swannsecurity com Swann Advanced Color Quad Processor 4 Channel Quad with Remote Control Swann Helpdesk D Has the answers R2 wee we a If this device does not work when you first plug it in do not take it back to the store Contact the Swann Helpdesk using our fast e mail service tech swann com au or call us on one of the Toll Free numbers shown on the back cover of this booklet Most problems can be quickly and easily fixed with a simple e mail or a quick chat with one of our friendly technical staff Toll Free available in the US and Australia only Installation Guide Introduction 2 Your Color Quad package comes with 2 Simple Connection Instructions 3 Operation Front Panel 4 Operation Rear Panel 5 Menu Screens 6 Technical Specifications J Warranty Information Back Cover Help Desk Support Details Back Cover Introduction The Swann Quad Processor is a low cost convenient security solution for monitoring up to four areas in your
Download Pdf Manuals
Related Search