Sunbeam 2600 Iron User Manual
Contents
1. not leave the iron unattended a hot iron it could lead to serious burns while it is plugged into the power outlet Iron only on an ironing board An iron takes approximately 30 minutes to cool down Allow the iron to cool completely before storing Sunbeam are very safety conscious when e Do not use an appliance for any purpose designing and manufacturing consumer products other than its intended use but it is essential that the product user also e Do not place an appliance on or near a hot gas exercise care when using an electrical appliance flame electric element or on a heated oven Listed below are precautions which are essential Do not place on top of any other appliance for the safe use of an electrical appliance e Do not let the power cord of an appliance hang Read carefully and save all the instructions over the edge of a table or bench top or touch provided with an appliance any hot surface Always turn the power off at the power outlet e For safety reasons and to avoid maintenance before you insert or remove a plug Remove by unskilled persons some appliances are by grasping the plug do not pull on the cord sealed using tamperproof screws Such Turn the power off and remove the plug appliances should always be returned to the when the appliance is not in use and nearest Sunbeam Appointed Service Centre before cleaning for adjustment or repair if required Do not use your appliance with an extension e Do not ope2. visible as the heat of the iron will fix the stains making them permanent Sunbeam and Ultura are registered trademarks of Sunbeam Corporation Made in China to Sunbeam s specification Due to minor changes in design or otherwise the product may differ from the one shown in this leaflet Backed by Sunbeam s 2 Year Replacement Guarantee and National Service Network Copyright SUNBEAM CORPORATION LIMITED 2005 A B N 45 000 006 771 Sunbeam Corporation is a division of GUD Holdings Ltd For more information or advice on this or any other Sunbeam appliance visit www sunbeam com au or contact the Sunbeam Consumer Service Line Australia 1800 025 059 New Zealand 0800 786 232 06 05 Sunbeam Consumer Hotline Australia 1800 025 059 New Zealand 0800 786 232 www sunbeam com au ee is a registered Trademark of Sunbeam WCL22E8 Corporation Limited ABN 45 000 006 771 Sunbeam Corporation Limited 2005
3. Sunbeam Ultura 2600 Platinum Dry Iron Instruction Booklet SR2600 Please read these instructions carefully and retain for future reference Sunbeam s Safety Precautions Features of your Ultura Dry Iron Using your Ultura Dry Iron Care and Cleaning lroning Guide adbel Eyi Ll olbLiial ai Go Sls aa PRATER LARS ebe Assurez vous que les pr cautions ci dessus relatives a la s curit sont bien comprises Versichern Sie sich daB die obenstehenden SicherheitsmaBnahmen Verstanden werden BeBaldvete nwo ol Napandavw mpopuAdeeic aopakeiac yivovtat KaTavont s Pastikan bahwa tindakan tindakan keselamatan seperti di atas dimengerti anda Accertatevi che le suddette norme di sicurezza siano comprese a dovere A CG Ga M L ozseegzt sau REEERE CSL Yeepete ce peka norope CroMeHaTUTe MepKn Ha npetnaanusBoct ce popo pas6pann Aseg rese de que las precauciones de seguridad precedentes sean bien comprendidas Syy dhs Laia YL clablaial aS iG gyt v si y zi od a ow o dasdlan Zoe 2ssc noer bee ng dunia Yukarda belirtilen g venlik nlemlerinin anla ld ndan emin olunuz Xin ki m chac rang nhng bi n ph p l m an to n k tr n duge hi u r N N Sunbeam s Safety Precautic Ka O NS SAFETY PRECAUTIONS FOR YOUR IRON e Do not wind the cord around the Do not leave a hot iron within reach of soleplate while the iron is still hot children If they come into contact with e Do
4. ature dial The thermostat light cycles on and off during ironing as the iron maintains the selected temperature Temperature indicator Align the desired setting with the temperature indicator Long cord with swivel cord outlet The swivel cord outlet is ideal for left or right hand use and provides greater versatility and ease of movement when ironing The flexible grommet protects the cord from fraying Temperature dial Allows you to select the desired temperature for each garment Stable heel rest Large heel rest keeps the iron stable on the ironing board Figure 1 Teflon Platinum Pro Full length button groove Cord wrap facility non stick soleplate For ironing around The built in cord wrap Glides easily across buttons facility allows you to wind all types of fabric and the cord around the heel for prevents sticking neat and tidy storage of the cord when the iron is not in use Before first use Remove any adhesive stickers plastic covers or cardboard sleeves from the soleplate Ensure that all adhesive is removed by rubbing the soleplate with a cloth dampened with methylated spirits NOTE When turned on for the first time your new iron may give off vapours for up to 10 minutes This is due to the initial heating of the materials used It is safe not detrimental to the performance of the iron and will not reoccur Using your iron Insert the 3 pin plug i
5. nto a 230 240 volt power outlet and turn the power on KA After each use 1 Turn the power off and remove the plug from the power outlet 2 Allow the iron to cool before winding the cord around the built in cord wrap Storage Always store the iron on its heel rest NOTE Do not store the iron with the soleplate facing down or in the carton Cleaning To clean the exterior of your iron wipe over with a damp soft cloth and wipe dry Caution Do not use harsh abrasives chemical cleaners or solvents to clean the exterior of your iron as these will damage the surface 2 Turn the temperature dial to the desired setting by aligning the setting on the dial with the temperature indicator The thermostat light will illuminate to indicate that the iron is heating to the selected temperature When the thermostat light goes out the iron is at the selected temperature and is ready to iron NOTE When the temperature dial is changed from a high setting to a lower temperature setting during ironing the thermostat light will go out immediately This indicates that the iron is cooling to the selected temperature To ensure that the iron has reached the selected temperature and is not too hot wait until the thermostat light comes on again and then goes out before ironing Cleaning the Teflon Platinum Pro non stick soleplate The non stick coating reduces sticking of fabrics and starches to the soleplate Do not iron over sharp objec
6. rate any electrical appliance with a cord unless this cord has been checked damaged cord or after the appliance has been and tested by a qualified technician or dropped or damaged in any manner If damage service person is suspected return the appliance to the Always use your appliance from a power nearest Sunbeam Appointed Service Centre outlet of the voltage A C only marked for examination repair or adjustment on the appliance For additional protection Sunbeam This appliance is not intended for use by young recommend the use of a residual current children or infirm persons unless they have device RCD with a tripping current not been adequately supervised by a responsible exceeding 30mA in the electrical circuit adult to ensure that they can use the appliance supplying power to your appliances safely e Do not immerse the appliance in water Never leave an appliance unattended while or any other liquid unless recommended in use Young children should be supervised to ensure that they do not play with the appliance If you have any concerns regarding the performance and use of your appliance please visit www sunbeam com au or contact the Sunbeam Consumer Service Line Ensure the above safety precautions are understood N a Dry Iron ura Features of your Ult Thermostat light IIluminates to indicate that the iron is heating and goes out when it has reached the temperature selected on the temper
7. ts such as buttons studs and zippers as these will scratch the surface Wipe the soleplate with a damp soft cloth after each use If polyester has burnt to the soleplate iron a damp cotton cloth while hot Caution Do not use scouring pads abrasives or harsh cleaners to clean your Teflon Platinum Pro soleplate as these will scratch and damage the surface Selecting ironing temperature Always read garment labels and follow the manufacturer s ironing instructions Hints for easier ironing Sort articles to be ironed according to the type of fabric This will reduce the need to adjust the temperature to suit varying garments Start with garments requiring lower temperatures and work your way through to items requiring higher temperatures If you are unsure of the fabric content of a garment test a small area such as a seam or inside hem section before ironing a visible area Start with a low temperature and gradually increase the heat to find the best setting for ironing the garment When reducing the temperature to iron sensitive fabrics allow approximately 2 minutes for the iron to cool to the new setting Pure woollen fabrics 100 wool can be ironed with the temperature dial set to Wool Use an ironing cloth to prevent shine marks on the fabric Fabrics such as velour wool linen and silk are best ironed with an ironing cloth to prevent shine marks Never iron areas of a garment where perspiration marks are
Download Pdf Manuals
Related Search