Stanton SMX.311 CD Player User Manual
Contents
1. When replacement parts are required be sure the service technician has used replacement parts specified by themanufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is waste Please refer to your localregulations for instructions on proper disposal of this product Carts and Stands The appliance should be used only with a cart or stand that is recommended by the manufacturer An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn The appliance coupler is used as the disconnect device the disconnect device shall remain readily operable in proper operating conditions This product is in compliance with EU WEEE regulations Disposal of end of life product should not be treated as municipal E WARNING To reduce the risk of electric shock do not expose this apparatus to rain or moisture Ensure that the apparatus is not exposed to splashing and that no objects filled with liquids such as vases are placed on the apparatus CAUTION CAUTION To reduce the risk of electric shock do not remove any cover No user serviceable parts inside Refer servicing to qualified personnel only RISK2. or C The appliance has been exposed to rain or D The appliance does not appear to operate normally or exhibits a marked change in performance or E The appliance has been dropped or the enclosure damaged Servicing The user should not attempt any service to the appliance beyond that described in the operating instructions All other servicing should be referred to qualified service personnel Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is the manufacturer s instructions have been adhered to Attachments do not use attachments not recommended by the product manufacturer as they may cause hazards Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer Replacement Parts
3. OFF always reverse this operation by turning off amplifiers then your mixer and then input devices Amp ar O Power 9 Supply oa nu DAT Power Amp For booth monitor y cocoa 9 7 Tape Deck S OO L LP ELE Figure 2 1 SMX 311 Description Top Panel 3 SMX 311 Description 3 1 Top Panel Figure 3 1 on 15 SMX 311 1 ON OFF TALK POWER CO 2 3 4 5 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 o o 7 MIC O w w 8 9 Figure 3 1 SMX 311 Description Top Panel 1 Mic ON OFF TALK Switch Turns the Mic ON or OFF When the switch is in the TALK position the mixer s sound level will decrease around 14 dB except the Mic channel so that the microphone is more clearly heard over the music 2 Mic Level Adjusts the microphone input level 3 CueLevel Adjusts the headphone volume output level 4 Cue Mix Allows you to preview channel audio to your headphones Listen here before bringing up channel faders or moving the crossfader 5 Channel EQ Adjusts the HI MID and LOW frequency levels of the Phono or Line input Range 26
4. Tech Support team can resolve your problem immediately avoiding down time due to shipping delays However if Tech Support determines that a repair is needed please call us at 1 954 949 9600 to obtain a Return Authorization Number RA PRIOR to shipping your product to us Warranty Service outside the United States To initiate a warranty repair please contact the authorized Stanton dealer from whom you purchased your product and follow the dealer s return policy Save your shipping boxes and all packaging materials For the fastest and safest product return to Stanton please use the original shipping carton and packaging materials Stanton cannot be responsible for any damages incurred during the shipping process due to poor or inadequate packing Please remember to insure your shipment Stanton Warranty To register your Stanton product on line please visit http www stantondj com v2 login product asp Model Type Model No Serial No Date of Purchase Dealer s Name Your Name Your Address E mail Address Please check this box CJ to receive updates and important information about Stanton via e mail How did you hear about us Dealer Magazine Friend Web Other Please specify Stanton www stantondj com Stanton Warranty Through Stanton s authorized dealers around the World Stanton or one of Stanton s authorized distributors outside the U S will w
5. OF ELECTRIC SHOCK The lighting flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product enclosure that may be significant enough to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintance servicing instructions in the literature accompanying this appliance CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure 1 Introd ction M 1 1 2 MX 3111 1 UOI 1 2 Quick Setup Diagram 1 O 2 3 SMX 311 5 A Rn ek 3 3 MERERETUR ODD LUTTE 3 3 2 p e 5 etie sese eer E ME reed 6 4 Troubleshooting nenne aE 7 Registration Card 8 Stanton Warranty TTE TIIILD G R 9 Specifications O 10 1 Introduction 1 1 Welcome to the SMX 311 Thank you for purchasing the SMX 311 Before starting please check tha
6. a non authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty To initiate a warranty repair you must contact the authorized Stanton dealer from whom you purchased the merchandise and follow such authorized Stanton dealer s return policy Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise Stanton s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise In no event will Stanton be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Stanton or otherwise To the extent permitted by law and except as otherwise provided above Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose The above warranty provides you with specific legal rights You may also have additional rights which are subject to variation from state to state and country to country If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above please includ
7. cables Some less expensive audio cables can be susceptible to hum and interference Keep your audio cables away from AC power cables and AC transformers Make sure the mixer is not mounted too close to high power amplifiers or lighting equipment power supplies or ballasts Make sure your turntables are properly grounded to the back of the mixer if they include a grounding wire hear feedback If you are using a microphone make sure that you are not too close to the speakers or headphones If you hear feedback on the Phono Input then the turntable may be mounted to close to the speakers and or subwoofer Also make sure the turntable base is placed on a surface that does not vibrate or resonate easily when the speakers are turned up loudly Registration Card nee ss ac MEE een PLACE STAMP HERE Stanton Magnetics Inc 772 S Military Trail Deerfield Beach FL 33442 USA Attn Technical Support l l l stanton www stantondj com Thank you for choosing Stanton Your satisfaction is extremely important to us We proudly stand behind the quality of our work and appreciate that you put your trust in us Registering your product will help us guarantee that you are kept up to date on our latest advances Warranty Service in the United States Please contact Stanton Tech Support BEFORE sending your product In some cases our
8. dB to 9 dB 6 Channel Fader Controls the output level of the selected input Phono or Line 7 Crossfader Controls the audio signal that is sent to the outputs When the Crossfader is set to CH 1 hard left only channel 1 Phono or Line will be sent to the outputs and when is set to CH 3 hard right only channel 3 Phono or Line will be sent to the outputs If the Crossfader is centered both channels will be sent to the outputs Channel 2 is not affected by the crossfader 8 Input Connect a standard unbalanced 1 4 microphone 9 Headphone Output Insert your headphones plug here 10 PFL Pre Fade Listen Buttons These buttons allows you to set each channel in CUE mode If you press CUE 1 for example the red LED located to its will glow the CH 1 signal will be sent to the headphones Set the CUE MIX knob 4 to the CUE position left To prevent any potential ear damage progressively adjust the cue level using the CUE LEVEL knob 3 11 Booth This knob allows you to adjust the level of the signal to be sent to the DJ Booth monitor system Please read 19 12 Pan Used to adjust the left right balance of the master output 13 Master Level Controls the overall output level 14 Gain Adjusts the volume of the Phono or Line input 15 Level Indicators The dual LED s indicators display the master output level 16 Source Input Selector Switch Selects the input source assigned to each channel Each cha
9. distortion GND To eliminate electrical hum connect the ground cable from your standard turntable ground post to the SMX 311 ground terminal Some turntables like the Stanton STR8 150 do not require a grounding wire SMX 311 Description Front Panel 3 3 Front Panel Figure 3 3 Figure 3 3 25 Microphone Input Mic Connect a standard unbalanced 1 4 microphone 26 Headphone Output Standard 1 4 headphone output connector Troubleshooting 4 Troubleshooting Problem Symptom Possible Cause Solution Is the power ON Based on your connections check that you have properly set the Channel Input Phone Line Make sure that the Input Gain Channel Fader and Master output are turned up Make sure the channels are properly assigned to the Crossfader No Sound Headphones Check the Cue Level Cue Mix and Cue button settings Mixer sounds noisy If a microphone is not being used move the Mic switch to the OFF position and turn all its related controls down Microphone doesn t work Is the Mic Level turned up Does the microphone require phantom power This mixer does not provide microphone phantom power Sound is distorted Line Input Turn down the Input Gain Control Check EQ settings Sound is distorted Phono Input Only plug turntables into this input do not plug in CD players or other Line Level sources Turn down the Input Gain Control and check EQ settings Make sure you are using good shielded audio
10. e a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein Specifications Input output impedance amp sensitivity ech B 10k ohm 54 0 1 dB 2mV Tonm 035 IV 7288 Master Bal Load 600 ohm 600 ohm 4 dBm 1 23V 2 dB of 28 MAPA S N ratio Maximum Gain EQ Flat W 20 kHz LPF A weighted THD N Master O dBV Output Maximum Gain W 20 kHz LPF Note O dBV 1V rms Crosstalk Line More than 65 dB at 1 kHz between L and R More than 70 dB at 1 kHz between Channels Channel EQ Hi 9 2 dB at 13 kHz 15 3 dB at 13 kHz Mid 9 2 dB at 1 kHz below 23 dB at 1 kHz Low 9 2 dB at 70 Hz below 23 dB at 70 Hz Dimensions H x W x D 100 mm x 254 mm x 308 mm 10 11 12 Stanton www stantondj com Copyright 2009 Stanton Magnetics Inc SMX 311 and STR8 150 are trademarks or registered trademarks of the Stanton Group All other trademarks are property of their respective owners who are in no way affiliated with Stanton DJ or SC System products All information included in the User Manual is subject to change without notice 1 954 949 9600 7500058 11 17 2009
11. ithout charge repair or replace at the sole discretion of the entity responsible for making the repair or providing the replacement any Stanton merchandise proved defective in material or workmanship for a period of one 1 year following the date of original purchase Exceptions to this warranty are as noted below The warranty for mechanical parts which are subject to wear and tear are limited to either the earlier of thirty 30 days following the date of original purchase or for 10 000 cycles for switches Stanton will warrant all replacement parts and repairs for ninety 90 days from the date of original shipment Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Returns Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country All goods requiring warranty repair or replacement must be returned freight prepaid if not hand delivered to the authorized Stanton dealer from whom the merchandise was purchased and in the same country where the merchandise was purchased For purposes of purchases made via the Internet the merchandise must be returned to the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the country where the purchaser is located or the country in which the merchandise was received Any returns to
12. nnel can be assigned to only one input source at a time SMX 311 Description Rear Panel 3 2 Rear Panel Figure 3 2 stanton R MASTER 299 x 00 0002000 LINE3 CH 3 LINE PHONO CH 1 Figure 3 2 17 18 19 20 21 22 23 24 Power Switch Turns the mixer ON or OFF Power Connector While the power is switched OFF plug the power supply into the mixer first and then plug it into the outlet Booth Output Using a RCA cable connect from the SMX 311 booth output to the DJ booth monitor system inputs Balanced Master output TRS balanced 1 4 connectors are typically used to connect to a P A mixer or an amplifier for live performances or a recording console Unbalanced Master output RCA connectors are typically used to connect to a home stereo or to another mixer with RCA inputs for practicing or team routines Line Inputs Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players Hi Fi VCRs cassette decks DAT machines laser discs tuners Mini Discs even synthesizers or other mixing consoles Plug mono audio sources into both Left and Right inputs using a Y cable connector Phono Inputs Plug your turntables in here When these connectors are used your signal is fed directly to the high quality RIAA phono pre amplifiers Only connect turntables here Line level sources will overload the sensitive phono pre amps and will cause
13. oduct dealer or local power company Grounding or Polarization This product may be equipped with a polarized alternation current line plug a plug having one blade widerthan the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the cord in correspondence of plugs convenience receptacles and the point where they exit from the appliance Cleaning The appliance should be cleaned only as recommended by the manufacturer Clean by wiping with a cloth slightly damp with water Avoid getting water inside the appliance Non use Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings Damage Requiring Service The appliance should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged or B Objects have fallen or liquid has been spilled into the appliance
14. stanten SMX 311 PROFESSIONAL TABLE TOP CD MIXER tal SMX 311 MIC O ON OFF TALK SE N 7 D 0 S 10 CUE LEVEL 10 N gt 7 E N ue O S CUE MIX 5 5 gt User Manual Important Safety Instructions Ur ow NP 10 11 12 13 14 15 16 17 18 19 20 21 22 Read Instructions All the safety and operating instructions should be read before this product is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Water and Moisture The appliance should not be used near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool and the like Heat Appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources This product should be operated only from the type of power source indicated on the rating label If you are not sure of the type of power supply to your home consult your pr
15. t you have received the following items SMX 311 unit e AC Adaptor e User Manual Now that you have checked that everything was included in the box let s talk about the SMX 311 1 2 Overview The SMX 311 is a compact 3 channel mixer that offers high end performance at a low cost With features like balanced outputs booth out replaceable crossfader and microphone talkover the SMX 311 is ready for duty in the club studio or mobile gig In addition the SMX 311 s functionality is wrapped in a rugged all metal inner chassis enclosure with a striking black and gray color scheme Let s summarize the main SMX 311 features Individual Low Mid High Master Booth Outs e 3 Line Phono 1 Microphone input e Balance Volume Control e 20 Segment Bright LEDs Grounding terminal Ok now that we ve covered the SMX 311 basics let s get started Quick Setup Diagram 2 Quick Setup Diagram Review this setup diagram Figure 2 1 Make sure all faders are at zero and all devices are OFF First connect all input sources and processors Next connect your microphone and monitor headphones Finally connect the stereo outputs to the power amplifier s and or audio receivers such as tape decks Plug your mixer into AC power Now you are ready to switch everything ON Important Always switch ON your audio input sources such as turntables or CD players first then your mixer and finally any amplifiers When turning
Download Pdf Manuals
Related Search