Sony DR-BT100CX Headphones User Manual
Contents
1. Low sound level gt Turn up the volume of this unit gt Turn up the volume on the connected device if necessary Low sound quality gt Switch the Bluetooth connection to A2DP Advanced Audio Distribution Profile when HSP Headset Profile is set Sound skips frequently during playback gt Reception condition of this unit may have become unstable due to improper matching of the bit rate setting for the music transmitted from the Bluetooth device and the environment in which this unit is used Terminate A2DP Bluetooth connection by operating the Bluetooth device While this unit is turned on press and hold BH for about 7 seconds to lower the setting of receivable bit rate Bit rate is a numerical value which represents data transmission volume per second The higher the bit rate in general the better quality the sound will be This unit can receive high bit rate music but sound skipping may occur depending on the usage environment When bit rate setting is completed the indicator blue flashes once The above operations may not reduce the sound skip depending on the usage environment To reset to the original setting press and hold B gt Ml again for about 7 seconds The indicator blue flashes twice 2 When calling The recipient s voice cannot be heard gt Check that both this unit and the Bluetooth mobile phone are turned on gt Check the connection between this unit2. Passcode may be called Passkey PIN code PIN number or Password Note Passcode may be not required depending on the connected Bluetooth device For details refer to the operating instructions supplied with the Bluetooth device 6 Start the Bluetooth connection from the Bluetooth device This unit memorizes the device as the last connected device Some Bluetooth devices may connect with the unit automatically when pairing is complete Tips To pair with other Bluetooth devices repeat steps 1 to 5 for each device To delete all pairing information see Initializing the unit page 27 13 14 Wearing the unit To use the clip 1 Clip this unit to a pocket etc of your clothes and then wear the headphones Wear the earphone marked in your left ear and the one marked in your right ear Tip Move the cord slider to change the split position of the cord to prevent the headphones coming apart when the unit is not in use How to install the earbuds correctly If the earbuds do not fit your ears correctly low bass sound may not be heard To enjoy better sound quality change the earbuds to another size or adjust the earbuds position to sit on your ears comfortably and fit your ears snugly If the earbuds do not fit your ears try another size Confirm the size of the earbuds by checking the colour inside When you change the earbuds install them firml
3. and the Bluetooth mobile phone Make a Bluetooth connection HFP or HSP again page 19 Check that output of the Bluetooth mobile phone is set for this unit Check that the volume of the unit is not set too low Turn up the volume on the connected Bluetooth mobile phone if necessary If you are listening to music using this unit stop playback press the multi function button and talk y Low sound from recipient gt Turn up the volume of this unit gt Turn up the volume on the connected Bluetooth mobile phone if necessary Initializing the unit You can reset this unit to its default such as volume setting and delete all pairing information 1 If this unit is turned on press and hold the POWER button for about 2 seconds to turn off this unit 2 Press and hold the POWER button and multi function button together for about 7 seconds The indicator blue flashes four times and this unit is reset to the default setting All pairing information is deleted 27 Specifications General purpose of Bluetooth communication between devices Codec Audio signal compression and conversion format t Subband Codec The optional accessories are not provided Output in some areas Bluetooth Specification Power Class 2 Communication System Bluetooth Specification version 2 1 EDR Enhanced Data Rate Maximum communication range Line of sight approx 10 m Frequency band 2 4 GHz
4. For example to make a call using a Bluetooth mobile phone while listening to music on a Bluetooth compatible music player this unit needs to be connected to the mobile phone using HFP or HSP Make a Bluetooth connection between this unit and the device in use following the procedures outlined below 1 Make a Bluetooth connection between this unit and the mobile phone in use with HFP or HSP following the procedures outlined in Calling page 19 2 Operate the Bluetooth device music player or mobile phone used for playing the music to make a Bluetooth connection to this unit using A2DP To make a call while playing To receive a call while playing back music back music When an incoming call arrives the music pauses and the ring tone is heard from this unit 1 Press the multi function button while playing back music page 21 or operate your Bluetooth mobile phone to make a telephone call T Press the multi function button and talk After finishing the call press the multi function button This unit is switched back to music playback If no dialing tone is heard on this unit press and hold the multi function button for about 2 seconds When no ring tone is heard even if an incoming call arrives 1 Stop music playback 2 When ringing press the multi function button and talk ADDITIONAL INFORMATION Precautions On Bluetooth communication Bluetooth wireless technology operates within a range of ab
5. cccssssssssesssscsssseseses 7 3 steps to Bluetooth function 8 Location and Function of Palts cccccsccsrssrcsssecsecsecsesseees 9 Charging the unit 00000 10 Pairing 008 12 What is pairing Procedures of pairing Wearing the unit 14 Indications of Bluetooth function ccscccscesscssscescseees 15 Listening to MUSIC 00000 16 Controlling the audio device AV RGD Essen 17 Callliing sccsccsccsssscsscescsscessesees 19 Controlling the Bluetooth mobile phone HEP HSP ou 21 Calling while playing back MUSIC cccccrcscceccccsscccssccesseee 22 Precautions ccccccscscesscseees 23 Troubleshooting s s000 25 Common When charging When listening to music When calling Initializing the unit 27 Specifications 28 General Headset System requirements for battery charge using USB 25 What is Bluetooth wireless technology Bluetooth wireless technology is a short range wireless technology that enables wireless data communication between digital devices such as a computer or digital camera Bluetooth wireless technology operates within a range of about 10 metres Connecting two devices as necessary is common but some devices can be connected to multiple devices at the same time You do not need to use a cable for connection nor is it necessary for the device
6. and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents CE Hereby Sony Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC For details please access the following URL http www compliance sony de Use of this radio equipment is not allowed in the geographical area within a radius of 20 km from the centre of Ny Alesund Svalbard in Norway Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences or the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased th
7. band 2 4000 GHz 2 4835 GHz Modulation method FHSS Compatible Bluetooth Profiles A2DP Advanced Audio Distribution Profile AVRCP Audio Video Remote Control Profile HSP Headset Profile HFP Hands free Profile Supported Codecs SBC MP3 Supported content protection method SCMS T Transmission range A2DP 20 20 000 Hz Sampling frequency 44 1 kHz Supplied accessories USB cable 1 Earbuds Sx2 Mx2 Lx2 Operating instructions this book 1 Recommended accessories Spare Earbuds EP EX10A not supplied USB charging AC power adaptor AC U50A not supplied The actual range will vary depending on factors such as obstacles between devices magnetic fields around a microwave oven static electricity reception sensitivity aerial s performance operating system software application etc 28 Bluetooth standard profiles indicate the Headset Power source DC 3 7 V Built in lithium ion rechargeable battery Dimension w h d excluding projection parts and controls Approx 19 5 x 74 0 x 17 5 mm Cord from unit to earpiece Approx 0 6 m Mass Approx 26 g including headphones 4g Rated power consumption 13W Receiver Type Closed dynamic Driver unit 9 mm dome type CCAW voice coil Frequency response 6 23 000 Hz Microphone Type Electret condenser Direction characteristic Omni directional Effective frequency range 100 4 000 Hz Operating te
8. sound played on this unit is slightly delayed from the sound played on the Bluetooth device during talking on the telephone or listening to the music Welcome Thank you for purchasing this Sony Wireless Stereo Headset This unit uses Bluetooth wireless technology Enjoy music wirelessly from Bluetooth Stereo enabled music players and mobile phones e Embedded microphone enables hands free conversation from Bluetooth enabled mobile phone Enjoy basic remote control operation play stop etc of music player functions via Bluetooth connection Bluetooth version 2 1 EDR for higher quality audio with less interference lower power consumption and easy connection USB rechargeable function Noise suppression and echo cancellation functions for superior conversation sound quality For details on Bluetooth wireless technology see page 6 Talking on the phone Listening to music The connected Bluetooth device is required to support A2DP Advanced Audio Distribution Profile The connected Bluetooth device is required to support HFP Hands free Profile or HSP Headset Profile 3 The connected Bluetooth device is required to support AVRCP Audio Video Remote Control Profile t Enhanced Data Rate 3 steps to Bluetooth function Pairing First register pair a Bluetooth device mobile phone etc and this unit with each other Once pairing is established there is no need for pair
9. Even if you change the volume while calling the volume for music playback does not change To stop use 1 Terminate the Bluetooth connection by operating the Bluetooth device 2 Press and hold the POWER button for about 2 seconds The indicator blue lights up and the unit turns off Tip When you finish playing music the Bluetooth connection may terminate automatically depending on the Bluetooth device Controlling the audio device AVRCP If the Bluetooth audio device connected with this unit supports AVRCP Audio Video Remote Control Profile you can control by using the unit buttons Refer to the operating instructions supplied with the Bluetooth device on how to operate it Note Operation of the Bluetooth connecting device by this unit will vary depending on its specification Status In stop or pause mode Short Press Long Press gt a Hea gt i Starts playback Stop Skip to next previous Fast forward Fast rewind Status In play mode Short Press Long Press gt Hea gt i Pause Stop Skip to next previous Fast forward Fast rewind You may need to press the button twice depending on the Bluetooth device Some Bluetooth devices may not operate Note You cannot adjust the volume of the Bluetooth device by pushing the jog switch of this unit up or down 17 Continued Tip Depen
10. S ONY 4 130 037 11 1 Wireless Stereo Headset Operating Instructions DR BT100CX Bluetooth 2009 Sony Corporation WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To reduce the risk of electrical shock do not open the cabinet Refer servicing to qualified personnel only Do not install the appliance in a confined space such as a bookcase or built in cabinet Do not expose the batteries battery pack or batteries installed to excessive heat such as sunshine fire or the like for a long time Excessive sound pressure from headphones can cause hearing loss The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Sony Corporation is under license Microsoft Windows and Windows Vista are registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Macintosh and Mac OS are trademarks of Apple Inc registered in the U S and other countries MPEG Layer 3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson Other trademarks and trade names are those of their respective owners Notice for customers the following information is only applicable to equipment sold in countries applying EU directives The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo Japan The Authorized Representative for EMC
11. cal devices Turn off this unit and other Bluetooth devices in the following locations as it may cause an accident where inflammable gas is present in a hospital train airplane or a petrol station near automatic doors or a fire alarm This unit supports security capabilities that comply with the Bluetooth standard to provide a secure connection when the Bluetooth wireless technology is used but security may not be enough depending on the setting Be careful when communicating using Bluetooth wireless technology We do not take any responsibility for the leakage of information during Bluetooth communication Connection with all Bluetooth devices cannot be guaranteed A device featuring Bluetooth function is required to conform to the Bluetooth standard specified by Bluetooth SIG Inc and be authenticated Even if the connected device conforms to the above mentioned Bluetooth standard some devices may not be connected or work correctly depending on the features or specifications of the device While talking on the phone hands free noise may occur depending on the device or communication environment Depending on the device to be connected it may require some time to start communication Contin ued 24 Note on static electricity In particularly dry air conditions mild tingling may be felt on your ears This is a result of static electricity accumulated in the body and not a ma
12. d Procedures of pairing 1 Place the Bluetooth device within 1 m of this unit Press and hold the PAIRING button for 2 seconds or more to standby for pairing while the unit is turned off The indicator blue and indicator red flash in turn and the unit enters into pairing mode Note If pairing is not established within about 5 minutes pairing mode will be cancelled and this unit will turn off In this case start over from step 1 3 Perform pairing procedure on the Bluetooth device to detect this unit The list of detected devices appears on the display of the Bluetooth device This unit is displayed as DR BT100CX If DR BT100CX is not displayed repeat from step 1 Notes For details refer to the operating instructions supplied with the Bluetooth device When pairing with a Bluetooth device that cannot display a list of detected devices or that has no display you may pair the device by setting both this unit and the Bluetooth device to pairing mode At this time if passcode is set besides 0000 on the Bluetooth device pairing cannot be done with this unit Select DR BT100CX on the display of the Bluetooth device If Passcode input is required on the display of a Bluetooth device input 0000 Pairing is complete when the indicator blue flashes slowly The message standing for Pairing complete appears on the display of some Bluetooth devices
13. d any problem persist consult your nearest Sony dealer Common The unit is not turned on gt Charge the battery of the unit gt The unit cannot be turned on while charging Remove the USB cable from the unit and then turn on the power Pairing cannot be done gt Bring this unit and the Bluetooth device closer together Cannot make the Bluetooth connection gt Check that this unit is turned on gt Check that the Bluetooth connecting device is turned on and the Bluetooth function is on gt Connection with the Bluetooth device may not be memorized on this unit Make the Bluetooth connection from the Bluetooth device to this unit soon after pairing is complete gt This unit or Bluetooth connecting device is in sleep mode gt The Bluetooth connection is terminated Make the Bluetooth connection again when listening to music see page 16 when calling see page 19 Distorted sound gt Ensure that this unit is not receiving interference from a wireless LAN other 2 4 GHz wireless device or microwave oven The correspondence distance is short Sound skips gt Ifa device that generates electromagnetic radiation such as a wireless LAN other Bluetooth device s or a microwave oven is nearby move away from such sources Point the aerial of this unit page 23 towards the Bluetooth device Make sure no obstacles blocks the communication The unit does not operate properly g
14. ding on the Bluetooth device the fast forward or fast rewind operation can be done by performing the following procedures on this unit 1 Press and hold the POWER button for about 2 seconds to turn off the unit 2 Press and hold the POWER button and jog switch BH for about 7 seconds The indicator blue flashes once The setting can be released by repeating the above procedures At this time the indicator blue flashes twice Note You cannot adjust the volume of the Bluetooth device by pushing the jog switch of this unit up or down When this unit does not connect to a Bluetooth mobile phone automatically You can make a connection by operating Bluetooth mobile phone or by operating this unit to connect the last connected Bluetooth device Jog switch VOL MIC A To make a connection by operating Bluetooth mobile phone POWER button NL Multi function button 1 Make the Bluetooth connection HFP or HSP from the Check the following before operating Bluetooth mobile phone to this the unit unit The Bluetooth function is active on the mobile phone Pairing of this unit and the Bluetooth mobile phone is complete 1 Press and hold the POWER button for about 2 seconds while the unit is turned off The indicator blue flashes twice the unit turns on and then this unit tries to connect to the last Bluetooth mobile phone that was used Tip This unit will stop tryin
15. e product Disposal of waste batteries applicable in the European Union and other European countries with separate collection systems This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste By ensuring these batteries are disposed of correctly you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery The recycling of the materials will help to conserve natural resources In case of products that for safety performance or data integrity reasons require a permanent connection with an incorporated battery this battery should be replaced by qualified service staff only To ensure that the battery will be treated properly hand over the product at end of life to the applicable collection point for the recycling of electrical and electronic equipment For all other batteries please view the section on how to remove the battery from the product safely Hand the battery over to the applicable collection point for the recycling of waste batteries For more detailed information about recycling of this product or battery please contact your local Civic Office your household waste disposal service or the shop where you purchased the product Table Of Contents What is Bluetooth wireless technology rss 6 Welcomel
16. g to connect to the Bluetooth mobile phone after 1 minute In such a case press the multi function button to try to connect again Refer to the manual supplied with your Bluetooth mobile phone for operation details The list of recognized devices appears on the display of the Bluetooth mobile phone This unit is displayed as DR BT100CX When you use the Bluetooth mobile phone features both HFP Hands free Profile and HSP Headset Profile set to HFP Note When connecting to a Bluetooth mobile phone which is different from the last connected one make the connection following the above procedure For details on profiles see page 6 Continued 20 B To make a connection with the last connected Bluetooth device by operating this unit Press the multi function button The indicator blue starts flashing and the unit performs the connection operation for about 5 seconds Note When listening to music with this unit a Bluetooth connection cannot be made with the multi function button To call 1 Use the buttons on your mobile phone when making a call If no dialing tone is heard on this unit press and hold the multi function button for about 2 seconds Tip You can call in the following way depending on the Bluetooth mobile phone Refer to the manual supplied with your mobile phone on operating details When not communicating you can call using the voice dial function by pre
17. ime up to Standby time up to 120 hours Time stated above may vary depending on ambient temperature or conditions of use Checking the remaining battery When pressing the POWER button while the unit is turned on the indicator red flashes You can check the remaining battery by the number of times the indicator red flashes Indicator red Status 3 times Full 2 times Mid 1 time Low needs to charge Note You cannot check the remaining battery immediately after the unit is turned on or while pairing When the battery is almost empty Indications of the Bluetooth function that are stated by the indicator blue changes to the indicator red When the battery becomes empty a beep sounds and the unit will turn off automatically 11 12 Pairing What is pairing Bluetooth devices need to be paired with each other beforehand Once Bluetooth devices are paired there is no need for pairing again except in the following cases Pairing information is deleted after repair etc This unit is paired with 9 or more devices This unit can be paired with up to 8 devices if a new device is paired after 8 devices have been paired the device whose latest connection time is the oldest among the 8 paired devices is replaced by the new one When recognition of the unit by the device to be connected is deleted This unit is initialized page 27 All pairing information is delete
18. ing again Bluetooth mobile phone etc Bluetooth connection Operate the Bluetooth device to make the Bluetooth connection Connection CD o gt Page 16 Listening to music You can listen to music played on the Bluetooth device Playback stop or pause is possible from this unit Music gt Page 17 18 Wireless Stereo Headset Page 12 13 Calling Bluetooth connection When the unit is turned on the unit starts making the Bluetooth connection to the recognized mobile phone automatically Connection gt Page 19 20 Talking on the phone You can make and receive a call by operating this unit gt Page 21 22 GETTING STARTED Location and Function of Parts 1 Headphones 8 Microphone 2 RESET button 9 POWER button 3 USB Y jack 10 2 Multi function button Z PAIRING button Controls various call functions 5 Cord slider 11 Clip 6 Indicator blue red Indicate the communication status blue or power status red of the unit 7 Jog switch Controls various functions when listening to music Adjust the volume of this unit when talking over the telephone Charging the unit The unit contains a rechargeable Lithium Ion battery which should be charged before using for the first time 1 Open the cove
19. lfunction of the headphones The effect can be minimized by wearing clothes made from natural materials Others Do not place this unit in a place exposed to humidity dust soot or steam subject to direct sunlight or in a car waiting at a traffic signal It may cause a malfunction Using the Bluetooth device may not function on mobile phones depending on radio wave conditions and location where the equipment is being used If you experience discomfort after using the Bluetooth device stop using the Bluetooth device immediately Should any problem persist consult your nearest Sony dealer Listening with this unit at high volume may affect your hearing For traffic safety do not use this unit while driving or cycling Do not put weight or pressure on this unit as it may cause the unit to deform during long storage Do not subject the headphones to excessive shock Clean the headphones with a soft dry cloth e If you have any questions or problems concerning this unit that are not covered in this manual please consult your nearest Sony dealer EP EX10A is available sold separately as optional replacement earbuds EP EX10A offers 4 types of the earbuds SS S M and L The optional accessory is not provided in some areas Troubleshooting If you run into any problems using this unit use the following checklist and read the product support information on our website Shoul
20. mperature 0 C to 45 C System requirements for battery charge using USB Personal Computer with pre installed with any of the following operating systems and USB port Operating Systems when using Windows Microsoft Windows Vista Home Basic Home Premium Business Ultimate Windows XP Home Edition Professional Media Center Edition Service Pack2 or later Media Center Edition 2004 amp 2005 Service Pack2 or later when using Macintosh Mac OS X version 10 3 or later Design and specifications are subject to change without notice 29 http www sony net Printed in Thailand
21. or blue lights up and the unit turns off Controlling the Bluetooth mobile phone HFP HSP The operation of the buttons on this unit varies depending on your mobile phone HFP Hands free Profile or HSP Headset Profile is used for Bluetooth mobile phone Refer to the operating instructions supplied with your Bluetooth mobile phone on supported Bluetooth profiles or how to operate HFP Hands free Profile Status Multi function button Short Press Long Press Standby Start Voice Last number Dial redial Voice Dial Cancel Voice active Dial Outgoing call End outgoing Change call call device Incoming call Answer Reject During call End call Change call device HSP Headset Profile Status Multi function button Short Press Long Press Standby Dial Outgoing call End outgoing End outgoing call call or change call device to headset Incoming call Answer During call End call Change call device to headset Some functions may not be supported depending on the Bluetooth mobile phone Refer to the operating instructions supplied with your mobile phone This may vary depending on the Bluetooth mobile phone Some functions may not be supported when calling using the Bluetooth mobile phone 21 Calling while playing back music The Bluetooth connection using HFP or HSP as well as A2DP is necessary to make a call while playing back music
22. out 10 metres Maximum communication range may vary depending on obstacles human body metal wall etc or electromagnetic environment The aerial is built into the unit as illustrated in the dotted line The sensitivity of the Bluetooth communication will improve by turning the direction of the built in aerial to the connected Bluetooth device The communication distance shortens when the obstacles are between the aerial of the connected device and this unit Location of built in aerial The following conditions may affect the sensitivity of Bluetooth communication There is an obstacle such as a human body metal or wall between this unit and Bluetooth device A device using 2 4 GHz frequency such as a wireless LAN device cordless telephone or microwave oven is in use near this unit Because Bluetooth devices and wireless LAN IEEE802 11b g use the same frequency microwave interference may occur and resulting in communication speed deterioration noise or invalid connection if this unit is used near a wireless LAN device In such as case perform the following Use this unit at least 10 m away from the wireless LAN device Ifthis unit is used within 10 m ofa wireless LAN device turn off the wireless LAN device Install this unit and Bluetooth device as near to each other as possible Microwaves emitting from a Bluetooth device may affect the operation of electronic medi
23. r of the USB Tips jack If the USB cable is connected to a computer while the unit is turned on the unit will be turned off automatically To charge the unit from an AC outlet use 2 Connect the supplied USB Y cable to the unit and then the USB charging AC power adaptor AC connect the other end toa U50A sold separately For details refer computer to the manuals supplied with the USB charging AC power adaptor When connecting insert the This unit cannot be turned on while connector with facing down charging The above optional accessory is not provided in some areas Charging starts when the unit and the computer are connected Make sure that the indicator red lights up Charging is completed in about 2 5 hours and the indicator red goes off automatically Time required for empty battery to recharge Notes If this unit is not used for a long time the indicator red may not light up when you connect the USB cable to charge this unit In this case do not disconnect the USB cable from the unit and wait until the indicator red lights up When you close the cover of the USB jack after charging push the cover thoroughly until the tab is full inserted For system requirements for a personal computer that can charge the battery using 1 0 USB see the Specifications page 29 Caution If this unit detects a problem while charging the indicator red may t
24. s to face one another such is the case with infrared technology For example you can use such a device in a bag or pocket Bluetooth standard is an international standard supported by thousands of companies all over the world and employed by various companies worldwide Communication System and Compatible Bluetooth Profiles of this unit Profile is standardization of the function for each Bluetooth device specification This unit supports the following Bluetooth version and profiles Communication System Bluetooth Specification version 2 1 EDR Compatible Bluetooth Profiles A2DP Advanced Audio Distribution Profile Transmitting or receiving audio content of high quality AVRCP Audio Video Remote Control Profile Controlling A V equipment pausing stopping starting playback volume control etc HSP Headset Profile Talking on the phone Operating the phone HFP Hands free Profile Talking on the phone Operating the phone by hands free Enhanced Data Rate When you use a Bluetooth mobile phone supported by both HFP Hands free Profile and HSP Headset Profile set to HEP Notes To be able to use the Bluetooth function the Bluetooth device to be connected requires the same profile as the unit s Note also that even if the same profile exists devices may vary in function depending on their specifications Due to the characteristic of Bluetooth wireless technology the
25. ssing the multi function button You can call the last dialed number by pressing the multi function button for about 2 seconds To receive a call When an incoming call arrives a ring tone will be heard from the unit 1 Press the multi function button on the unit The ring tone differs in the following ways depending on your mobile phone ring tone set on the unit ring tone set on the mobile phone ring tone set on the mobile phone only for Bluetooth connection Note If you received a call by pressing the button on the Bluetooth mobile phone some Bluetooth mobile phones may have handset use priority In this case set to talk with the unit by pressing and holding the multi function button for about 2 seconds or by operating the Bluetooth mobile phone For details refer to the manual supplied with your Bluetooth mobile phone To adjust the volume Push the jog switch up or down to adjust the volume Tips You cannot adjust the volume when not communicating Volume for calling and listening to music can be adjusted independently Even if you change the volume while playing back the music the volume of a call does not change To terminate a call You can end a call by pressing the multi function button on the unit To stop use 1 Terminate Bluetooth connection by the Bluetooth mobile phone 2 Press and hold the POWER button for about 2 seconds to turn off the power The indicat
26. t Reset the unit Pairing information is not deleted by this operation Insert a small pin etc into the hole and push until you feel a click 25 Continued 26 When charging Charging cannot be done gt Check that the unit and the computer are firmly connected by the USB cable gt Check that the computer is turned on gt Check that the computer is not in standby sleep or hibernation mode Charging time is too long gt Check that the unit and the computer are directly connected not via a USB hub The unit cannot be recognized by a computer gt The USB cable is not connected properly to the USB port of the computer Connect the USB cable again gt Check that the unit and the computer are directly connected not via a USB hub gt A problem may occur with the connected USB port of the computer Connect to another USB port if it is available gt Try the USB connection procedure again in cases other than those stated above When listening to music No sound gt Bluetooth device are turned on gt A2DP Bluetooth connection is not made between this unit and the Bluetooth device Make an A2DP Bluetooth connection page 16 gt Check that music is being played back by the Bluetooth device gt Check that the volume of the unit is not set too low gt Turn up the volume on the connected device if necessary gt Pair this unit and Bluetooth device again page 12
27. te After the unit is turned on the unit attempts to connect to the last connected Bluetooth device automatically with HFP or HSP When not calling with this unit do not make the last connected Bluetooth device ready for HFP or HSP connection To make or receive a call while playing back music see page 22 2 Make the Bluetooth connection A2DP from a Bluetooth device to this unit Refer to the operating instructions supplied with the Bluetooth device on how to operate it 3 Start playback on the Bluetooth device Tip Bluetooth connection of A2DP Advanced Audio Distribution Profile can also be operated with the jog switch from this unit to the Bluetooth device except when making a call on this unit Notes When you play music by connecting the unit to a Bluetooth device using HSP Headset Profile sound quality will not be high For better sound change the Bluetooth connection to A2DP by operating the Bluetooth device e If this unit is turned off while an A2DP Bluetooth connection is established operate the unit again from step 1 to make the A2DP Bluetooth connection again For detail on profiles see page 6 To adjust the volume Push the jog switch up or down while listening to music to adjust the volume Tips Depending on the connected device it may be necessary to adjust the volume on the connected device as well Volume for calling and listening to music can be adjusted independently
28. urn off although charging is not complete Check for the following causes Ambient temperature exceeds the range of 0 C 40 C There is a problem with the battery In this case charge again within the above mentioned temperature range If the problem persists consult your nearest Sony dealer Notes If the battery is not used for a long time battery may be quickly depleted however after a few recharges battery life will improve If the life of the built in rechargeable battery drops to half the normal length the battery should be replaced Consult your nearest Sony dealer for replacement of the rechargeable battery Avoid exposure to temperature extremes direct sunlight moisture sand dust or mechanical shock Never leave in a car parked in the sun Use only the supplied USB cable Do not use any other USB cable If the computer enters into hibernation mode while connected to the unit charging will not be completed properly Check the setting of the computer before charging The indicator red will go off automatically even if the computer enters into hibernation mode Charge the unit again in this case Use the supplied USB cable only and connect directly to a computer Charging will not be completed properly by an indirect connection such as via a USB hub Usage hours Status Approx usage hours Communication time 8 hours including music playback t
29. y on the headphones to prevent the earbud from detaching and remaining in your ear DE pp Indications of Bluetooth function Status Flashing patterns Indicator blue Indicator red Searching Connecting Pairing Connectable Connecting Connected HEP HSP or A2DP standby for receiving audio signal HFP HSP and A2DP standby for receiving audio signal Apap AD x o pw Music Listening Listening during standby for telephone call Phone Incoming call Talking Calling while playing back music Oo x amp DO DO x o 15 16 OPERATING THE UNIT Listening to music Jog switch VOL POWER he This unit supports SCMS T content protection You can enjoy music etc from a device such as a mobile phone or portable TV that supports SCMS T content protection Check the following before operating the unit The Bluetooth device is turned on Pairing of this unit and the Bluetooth device is complete The Bluetooth device supports the transmitting music function profile A2DP 1 Press and hold the POWER button for about 2 seconds while the unit is turned off The indicator blue flashes twice and the unit is turned on No
Download Pdf Manuals
Related Search