Home

Saturn 2009 VUE Automobile User Manual

1. e A hill that can be driven straight up or down might be too steep to drive across When going straight up or down a hill the length of the wheel base the distance from the front wheels to the rear wheels reduces the likelihood the vehicle will tumble end over end But when driving across an incline the narrower track width the distance between the left and right wheels might not prevent the vehicle from tilting and rolling over Driving across an incline puts more weight on the downhill wheels which could cause a downhill slide or a rollover Surface conditions can be a problem Loose gravel muddy spots or even wet grass can cause the tires to slip sideways downhill If the vehicle slips sideways it can hit something that will trip it a rock a rut etc and roll over Hidden obstacles can make the steepness of the incline even worse If you drive across a rock with the uphill wheels or if the downhill wheels drop into a rut or depression the vehicle can tilt even more For these reasons carefully consider whether to try to drive across an incline Just because the trail goes across the incline does not mean you have to drive it The last vehicle to try it might have rolled over If you feel the vehicle starting to slide sideways turn downhill This should help straighten out the vehicle and prevent the side slipping The best way to prevent this is to walk the course
2. For information about using tire chains on the vehicle see Tire Chains on page 5 62 4 27 Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels Turn off any traction or stability system Shift back and forth between R Reverse and a forward gear or with a manual transmission between 1 First or 2 Second and R Reverse spinning the wheels as little as possible To prevent transmission wear wait until the wheels stop spinning before shifting gears Release the accelerator pedal while shifting and press lightly on the accelerator pedal when the transmission is in gear Slowly spinning the wheels in the forward and reverse directions causes a rocking motion that could free the vehicle If that does not get the vehicle out after a few tries it might need to be towed out If the vehicle does need to be towed out see Towing Your Vehicle on page 4 32 4 28 Loading the Vehicle It is very important to know how much weight your vehicle can carry This weight is called the vehicle capacity weight and includes the weight of all occupants cargo and all nonfactory installed options Two labels on your vehicle show how much weight it may properly carry the Tire and Loading Information label and the Certification Tire label Driving Your Vehicle Z CAUTION Do not load the vehicle any heavier than the Gross Vehicle Weight Rating GV
3. A right front passenger takes his her weight off of the seat for a period of time e The right front passenger seat is occupied by a smaller person such as a child who has outgrown child restraints e Or if there is a critical problem with the airbag system or the passenger sensing system 1 53 When the passenger sensing system has turned off the right front passenger frontal airbag and seat mounted side impact airbag the off indicator will light and stay lit to remind you that the airbags are off See Passenger Airbag Status Indicator on page 3 30 The passenger sensing system is designed to turn on may inflate the right front passenger frontal airbag and seat mounted side impact airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat When the passenger sensing system has allowed the airbags to be enabled the on indicator will light and stay lit to remind you that the airbags are active 1 54 For some children who have outgrown child restraints and for very small adults the passenger sensing system may or may not turn off the right front passenger frontal airbag and seat mounted side impact airbag depending upon the person s seating posture and body build Everyone in the vehicle who has outgrown child restraints should wear a safety belt properly whether or not there is an airbag for that person Z CAUTION If the air
4. 5 82 Windshield Wiper 5 80 G Gage Speedometer 0655 3 28 Tachometer 2 60000 3 28 Gages Fuel eeror n ss 3 41 Trip Odometer c a 3 28 Garage Door Opener 2 37 Gasoline Octane ccceeeeeeeeee eee ees 5 5 Specifications ee 5 6 Gate Ajar Light 8 Glove BOX 0 ceeeeeeeee es GM Mobility Reimbursement Programi esnie Halogen Bulbs 4 Hazard Warning Flashers Head Restraints Headlamp Aiming Headlamps arncanciiiicorenan Bulb Replacement Daytime Running Lamps DRL Exterior Lamps 4 Flash to Pass iniia High Low Beam Changer Wiper Activated Heated Seats cccccecee eee Healer osson Engine Coolant Height Adjuster Driver Seat Highbeam On Light High Speed Operation Tires 4 cseanreecdinx sender s ennas i 6 INDEX Highway Hypnosis Hill and Mountain Roads Hood Checking Things Under Release Horn How to Wear Safety Belts Properly Ignition Positions Infants and Young Children Restraints Inflation Tire Pressure Instrument Panel Brightness Cluster OVEIVIEW ccc ccee cece ee eee ees Storage Area 0 0085 Introduction Jump Starting K Keyless Entry Remote Operation ceeeeeeeee
5. 6 12 3 With the engine off turn the ignition to ON RUN but do not start the engine Without applying the regular brake try to move the shift lever out of P Park with normal effort If the shift lever moves out of P Park contact your dealer retailer for service Ignition Transmission Lock Check While parked and with the parking brake set try to turn the ignition to LOCK OFF in each shift lever position e For automatic transmission vehicles the ignition should turn to LOCK OFF only when the shift lever is in P Park The ignition key should come out only in LOCK OFF e For manual transmission vehicles the ignition key should come out only in LOCK OFF Contact your dealer retailer if service is required Maintenance Schedule Parking Brake and Automatic Transmission P Park Mechanism Check Z CAUTION When you are doing this check the vehicle could begin to move You or others could be injured and property could be damaged Make sure there is room in front of the vehicle in case it begins to roll Be ready to apply the regular brake at once should the vehicle begin to move Park on a fairly steep hill with the vehicle facing downhill Keeping your foot on the regular brake set the parking brake e To check the parking brake s holding ability With the engine running and transmission in N Neutral slowly remove foot pressure from the regular brake pedal
6. If the vehicle does not have a rear seat that will accommodate a rear facing child restraint a rear facing child restraint should not be installed in the vehicle even if the airbag is off When securing a child restraint ina rear seating position study the instructions that came with your child restraint to make sure it is compatible with this vehicle 1 31 Wherever a child restraint is installed be sure to secure the child restraint properly Keep in mind that an unsecured child restraint can move around ina collision or sudden stop and injure people in the vehicle Be sure to properly secure any child restraint in the vehicle even when no child is in it Lower Anchors and Tethers for Children LATCH The LATCH system holds a child restraint during driving or in a crash This system is designed to make installation of a child restraint easier The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system 1 32 Make sure that a LATCH compatible child restraint is properly installed using the anchors or use the vehicle s safety belts to secure the restraint following the instructions that came with that restraint and also the instructions in this manual When installing a child restraint with a top tether you must also use either the lower anchors or the safety belts to properly secure the child restraint A child restraint mus
7. Tire Pressure If your vehicle has the Tire Pressure Monitor System TPMS the pressure for each tire can be viewed in the DIC The tire pressure will be shown in either pounds per square inch psi or kilopascals kPa Press the vehicle information button until the DIC displays FRONT TIRES PSI kPa LEFT RIGHT Press the vehicle information button again until the DIC displays REAR TIRES PSI kPa LEFT RIGHT If a low or high tire pressure condition is detected by the system while driving a message advising you to check the pressure ina specific tire will appear in the display See Inflation Tire Pressure on page 5 49 and DIC Warnings and Messages on page 3 49 for more information If the tire pressure display shows dashes instead of a value there may be a problem with your vehicle If this consistently occurs see your dealer retailer for service Relearn Remote Key This display allows you to match Remote Keyless Entry RKE transmitters to your vehicle This procedure will erase all previously learned transmitters Therefore they must be relearned as additional transmitters To match an RKE transmitter to your vehicle 1 Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays Press the set reset button until REMOTE KEY LEARNING ACTIVE is displayed Press and hold the lock and unlock buttons on the first transmitter at the same time for about 15 second
8. Filling the Tank Z CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries To help avoid injuries to you and others read and follow all the instructions on the pump island Turn off the engine when you are refueling Do not smoke if you are near fuel or refueling the vehicle Do not use cellular phones Keep sparks flames and smoking materials away from fuel Do not leave the fuel pump unattended when refueling the vehicle This is against the law in some places Do not re enter the vehicle while pumping fuel Keep children away from the fuel pump never let children pump fuel Unlock the gas cap door by pressing the door lock switch located on the driver door trim The tethered fuel cap is located behind a hinged fuel door on the driver side of the vehicle To remove the fuel cap turn it slowly counterclockwise The fuel cap has a spring in it if the cap is released too soon it will spring back to the right To avoid fuel contact on the painted surface of the vehicle when filling the fuel tank place the tethered cap on the fuel filler door Z CAUTION Fuel can spray out on you if you open the fuel cap too quickly If you spill fuel and then something ignites it you could be badly burned This spray can happen if the tank is nearly full and is more likely in hot weather Open the fuel cap slowly and wait for any hiss noise to stop Then unscrew the cap all
9. cable to the negative terminal of the good battery Use a remote negative terminal if the vehicle has one Do not let the other end touch anything until the next step The other end of the negative cable does not go to the dead battery It goes to a heavy unpainted metal engine part or to a remote negative terminal on the vehicle with the dead battery Connect the other end of the negative cable away from the dead battery but not near engine parts that move The electrical connection is just as good there and the chance of sparks getting back to the battery is much less 5 34 Service and Appearance Care 10 Now start the vehicle with the good battery and run the engine for a while 11 Press the unlock symbol on the remote keyless entry transmitter to disarm your security system if equipped 12 Try to start the vehicle that had the dead battery If it will not start after a few tries it probably needs service Notice If the jumper cables are connected or removed in the wrong order electrical shorting may occur and damage the vehicle The repairs would not be covered by the vehicle warranty Always connect and remove the jumper cables in the correct order making sure that the cables do not touch each other or other metal Jumper Cable Removal A Heavy Unpainted Metal Engine Part or Remote Negative Terminal B Good Battery or Remote Positive and Remote
10. Chains Tire Charging System Light Check Engine Lamp Checking Things Under the Hood seeneniit Chemical Paint Spotting Child Restraints Infants and Young Children 00008 Lower Anchors and Tethers for Children Child Restraints cont Older Children Securing a Child Restraint in a Rear Seat Position Securing a Child Restraint in the Right Front Seat Position Systems Where to Put the Restraint Chime Level Adjustment Circuit Breakers Cleaning Aluminum Wheels Exterior Lamps Lenses Fabric Carpet Finish Care ccccceeeaee Instrument Panel Vinyl and Other Plastic Surfaces Interior Leather Tires Underbody Maintenance Washing Your Vehicle Cleaning cont Weatherstrips Windshield and Wiper Blades Climate Control System Outlet Adjustment Climate Control Systems Automatic Clock Setting Collision Damage Repair Compact Spare Tire Compass Content Theft Deterrent Control of a Vehicle Convenience Net Coolant Engine Engine Temperature Warning Light Surge Tank Pressure Cap Cooling System Courtesy Transportation Cruise Control Cruise Control Light Cupholders INDEX Customer Assistance Offices Text Telephone TTY Users Customer Information Service Publications Ordering Information Customer Satisfaction Procedure Damage Repair Collision Data Recorders
11. Unlike average fuel economy this display cannot be reset Blank Display This display shows no information Instrument Panel 3 45 Vehicle Information Menu ltems i Vehicle Information Press this button to scroll through the following menu items Oil Life Press the vehicle information button until OIL LIFE REMAINING displays This display shows an estimate of the oil s remaining useful life If you see 99 OIL LIFE REMAINING on the display that means 99 of the current oil life remains The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions 3 46 Instrument Panel When the remaining oil life is low the CHANGE ENGINE OIL SOON message will appear on the display See CHANGE ENGINE OIL SOON under DIC Warnings and Messages on page 3 49 You should change the oil as soon as you can See Engine Oil on page 5 14 In addition to the engine oil life system monitoring the oil life additional maintenance is recommended in the Maintenance Schedule in this manual See Scheduled Maintenance on page 6 3 for more information Units Press the vehicle information button until UNITS displays This display allows you to select between English or Metric units of measurement Once in this display press the set reset button to select between ENGLISH or METRIC units All of the vehicle information will then be displayed in the unit of measurement selected
12. Z CAUTION Try to drive straight up the hill if at all possible If the path twists and turns you might want to find another route Driving to the top crest of a hill at full speed can cause an accident There could be a drop off embankment cliff or even another vehicle You could be seriously injured or killed As you near the top of a hill slow down and stay alert Push the brake pedal to stop the vehicle and keep it from rolling backwards and apply the parking brake If the engine is still running shift the transmission to R Reverse release the parking brake and slowly back down the hill in R Reverse If the engine has stopped running you need to restart it With the brake pedal pressed and the parking brake still applied shift the transmission to P Park and restart the engine Then shift to R Reverse release the parking brake and slowly back down the hill as straight as possible in R Reverse While backing down the hill put your left hand on the steering wheel at the 12 o clock position so you can tell if the wheels are straight and can maneuver as you back down It is best to back down the hill with the wheels straight rather than in the left or right direction Turning the wheel too far to the left or right will increase the possibility of a rollover Things not to do if the vehicle stalls or is about to stall when going up a hill Never attempt to p
13. Z CAUTION If the airbag readiness light stays on after the vehicle is started or comes on while driving it means the airbag system might not be working properly The airbags in the vehicle might not inflate in a crash or they could even inflate without a crash To help avoid injury have the vehicle serviced right away rt The airbag readiness light comes on when the vehicle is started and flashes for a few seconds The light goes out when the system is ready 3 30 Instrument Panel If the airbag readiness light stays on after the vehicle is started or comes on while driving the airbag system may not work properly Have the vehicle serviced right away The airbag readiness light should flash for a few seconds when the engine is started If the light does not come on then have it fixed immediately If there is a problem with the airbag system an airbag Driver Information Center DIC message may also come on See DIC Warnings and Messages on page 3 49 for more information Passenger Airbag Status Indicator The vehicle has the passenger sensing system See Passenger Sensing System on page 1 51 for important safety information The instrument panel has a passenger airbag status indicator E PASSENGER AIRBAG OFF OH A United States Me Bo Canada Ai When the vehicle is started the passenger airbag status indicator will light ON and OFF or the symbol for on and off fo
14. use spare tires tires with nominal rim diameters of 10 to 12 inches 25 to 30 cm or to some limited production tires While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria TPC standards Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and a half 1 5 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B C The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled co
15. 1 Move the shift lever from D Drive rearward to M Manual The six speed transmission will downshift to a lower gear and the instrument panel will display the gear range selected If equipped with a 4 speed transmission it will display a 3 for third gear range When coming to a stop in the manual position the vehicle will automatically shift to 1 First gear 2 Press the plus button to upshift or the minus button to downshift Features and Controls While using the MSM feature the vehicle will have sportier performance You can use this when driving hilly roads to stay in gear longer or to downshift for more power or engine braking The transmission will only allow you to shift into a gear range appropriate for the vehicle speed e The transmission will not automatically shift to the next higher gear range without pressing the button on the shifter handle e The transmission will not allow shifting to the next lower gear if the vehicle speed is too high If the vehicle does not respond to a gear change or detects a problem with the transmission the range of gears may be reduced and the Malfunction Indicator Lamp will come on See Malfunction Indicator Lamp on page 3 35 Parking Brake The parking brake lever is located in the center console between the front seats To set the parking brake hold the brake pedal down and pull up on the parking brake lever If the ignition
16. And you can unbuckle a safety belt even if you are upside down Q If my vehicle has airbags why should have to wear safety belts A Airbags are supplemental systems only so they work with safety belts not instead of them Whether or not an airbag is provided all occupants still have to buckle up to get the most protection That is true not only in frontal collisions but especially in side and other collisions 1 13 Q If am a good driver and never drive far from home why should I wear safety belts A You may be an excellent driver but if you are in a crash even one that is not your fault you and your passenger s can be hurt Being a good driver does not protect you from things beyond your control such as bad drivers Most accidents occur within 25 miles 40 km of home And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph 65 km h Safety belts are for everyone 1 14 How to Wear Safety Belts Properly This section is only for people of adult size Be aware that there are special things to know about safety belts and children And there are different rules for smaller children and infants If a child will be riding in the vehicle see Older Children on page 1 23 or Infants and Young Children on page 1 26 Follow those rules for everyone s protection It is very important for all occupants to buckle up Statistics show that unbel
17. E AaS Notice Driving with the engine coolant temperature warning light on could cause the vehicle to overheat See Engine Overheating on page 5 25 The vehicle s engine could be damaged and it might not be covered by the vehicle warranty Never drive with the engine coolant temperature warning light on If this light comes on and stays on the engine has overheated Pull over and see Engine Overheating on page 5 25 for more information Tire Pressure Light 1 If the vehicle has a tire pressure monitoring system the tire pressure light provides information about tire pressures and the Tire Pressure Monitoring System The light should come on briefly as the engine is started If it does not have the vehicle serviced by your dealer retailer When the Light is On Steady This indicates that one or more of the tires are significantly underinflated A tire pressure message in the Driver Information Center DIC can accompany the light See DIC Warnings and Messages on page 3 49 for more information Stop and check the tires as soon as it is safe to do so If underinflated inflate to the proper pressure See Tires on page 5 43 for more information When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System The light flashes for about a minute and stays on steady for the remainder of the ignition cycle This sequence re
18. GCOMntrOl oseere nne 3 92 Radio Reception 3 92 Fixed Mast Antenna 3 93 XM Satellite Radio Antenna System eseeeeee 3 93 Chime Level Adjustment 3 93 Instrument Panel 3 3 4 NOTES 3 4 Instrument Panel Instrument Panel Overview a ae The main components of the instrument panel are the following A Outlet Adjustment on page 3 24 B Instrument Panel Brightness on page 3 14 C Turn Signal Multifunction Lever on page 3 6 D Instrument Panel Cluster on page 3 27 Windshield Wipers on page 3 7 Audio System s on page 3 64 Auxiliary Input Jack See Radio s on page 3 67 H Fog Lamps on page 3 14 Exterior Lamps on page 3 12 Driver Information Center DIC on page 3 42 J Instrument Panel Storage on page 2 42 K Hood Release on page 5 11 Cruise Control on page 3 9 Tilt Wheel on page 3 6 omm zr W Horn on page 3 5 Audio Steering Wheel Controls on page 3 92 Rear Window Wiper Washer on page 3 9 Traction Control System TCS on page 4 8 Shift Lever See Automatic Transmission Operation Uplevel on page 2 19 or Automatic Transmission Operation Base on page 2 22 Climate Control System on page 3 17 or Automatic Climate Control System on page 3 20 If Equipped Hazard Warning Flashers on page 3 5 Passenger Airbag Status Indicator on page 3 30 Safety Belt Reminders on
19. Instrument Panel Overview 3 4 Hazard Warning Flashers 3 5 ol an E E E E AE 5 Tilt Wheel isiirisini iecere 3 6 Turn Signal Multifunction Lever ea teste tees 3 6 Turn and Lane Change Signals sisme taierea 3 6 Headlamp High Low Beam CHANGER sie cccs sorcensscutaccasesree 3 7 Flash to Pass e eseeeeeeeee 3 7 Windshield Wipers 3 7 Rainsense Wipers 3 8 Windshield Washer 3 8 Rear Window Wiper Washer 3 9 Cruise Control i erreser a 3 9 Exterior LAMPS ceeeeeeeees 3 12 Wiper Activated Headlamps ses iiererrsssisinse 3 12 Daytime Running Lamps DRL Automatic Headlamp System Fog Lamps Instrument Panel Brightness Dome Lamp Entry Lighting Reading Lamps Electric Power Management Battery Run Down Protection Accessory Power Outlet s Climate Controls Climate Control System Automatic Climate Control System Outlet Adjustment Passenger Compartment Air Filter Instrument Panel Warning Lights Gages and Indicators Warning Lights Gages and Indicators Instrument Panel Cluster Speedometer and Odometer Trip Odometer Tachometer Safety Belt Reminders Airbag Readiness Light Passenger Airbag Status Indicator Charging System Light Brake System Warning Light Antilock Brake System ABS Warning Light Power Steering Warning Lights Traction Control System TCS Warning Light StabiliTrak
20. Radio Messages for XM Only See XM Radio Messages on page 3 79 later in this section for further detail Radio Messages Calibration Error The audio system has been calibrated for the vehicle from the factory If Calibration Error displays it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer retailer for service Locked This message displays when the THEFTLOCK system has locked up the radio Take the vehicle to your dealer retailer for service If any error occurs repeatedly or if an error cannot be corrected contact your dealer retailer Playing a CD Single CD Player Insert a CD partway into the slot label side up The player pulls it in and the CD should begin playing Playing a CD s Six Disc CD Player LOAD Press to load CDs into the CD player This CD player holds up to six CDs To insert one CD 1 Press and release the 7 button 2 Wait for the message to insert the disc 3 Load a CD Insert the CD partway into the slot label side up The player pulls the CD in Instrument Panel 3 71 To insert multiple CDs 1 Press and hold the 7 button for two seconds A beep sounds and Load All Discs displays 2 Follow the displayed instruction on when to insert the discs The CD player takes up to six CDs 3 Press the 7 button again to cancel loading more CDs If the ignition or radio is turned off with a CD
21. START This is the position that starts the engine When the engine starts release the key The ignition switch returns to ON RUN for driving A warning tone will sound when the driver door is opened the ignition is in ACC ACCESSORY or LOCK OFF and the key is in the ignition Retained Accessory Power RAP These vehicle accessories may be used for up to 10 minutes after the ignition key is turned to the LOCK position e Outside Mirror e Power Windows e Sunroof if equipped e Radio The outside mirror power windows and sunroof will function until a door is opened The radio will function until the driver door is opened Starting the Engine Move the shift lever to P Park or N Neutral The engine will not start in any other position To restart the engine when the vehicle is already moving use N Neutral only Features and Controls Notice Do not try to shift to P Park if the vehicle is moving If you do you could damage the transmission Shift to P Park only when the vehicle is stopped Starting Procedure 1 With your foot off the accelerator pedal turn the ignition to START When the engine starts let go of the key The idle speed will slow down as the engine warms Do not race the engine immediately after starting it Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts The vehicle has a Computer Controlled Cranking System Thi
22. but it actually took a little more or less than half the tank s capacity to fill the tank e The gage moves alittle while turning a corner or speeding up The gage takes a few seconds to stabilize after the ignition is turned on but it goes back to empty when the ignition is turned off For fuel tank capacity see Capacities and Specifications on page 5 86 Instrument Panel 3 41 Low Fuel Warning Light ny The low fuel warning light below the fuel gage comes on briefly when the engine is started This light also comes on when the fuel tank is low on fuel When fuel is added the light should go off If it does not have the vehicle serviced 3 42 Instrument Panel Driver Information Center DIC Your vehicle has a Driver Information Center DIC All information appears in the DIC display located in the instrument panel cluster The DIC comes on when the ignition is on After a short delay the DIC displays the information that was last displayed before the engine was turned off The DIC displays trip fuel and vehicle system information and warning messages if a system problem is detected The DIC also displays the compass direction outside air temperature and shift position indicator at the top of the DIC display If there is a problem with the system that controls the temperature display the numbers will be replaced with dashes If this occurs have the vehicle serviced by you
23. followed by a tone 3 Say Voice The system responds with OK accessing lt phone name gt e The cell phone s normal prompt messages will go through its cycle according to the phone s operating instructions 3 90 Instrument Panel Dual Tone Multi Frequency DTMF Tones The in vehicle Bluetooth system can send numbers and numbers stored as name tags during a call This is used when calling a menu driven phone system Account numbers can be programmed into the phonebook for retrieval during menu driven calls Sending a Number During a Call 1 Press The system responds with Ready followed by a tone 2 Say Dial The system responds with Say a number to send tones followed by a tone 3 Say the number to send e If the system clearly recognizes the number it responds with OK Sending Number and the dial tones are sent and the call continues e Ifthe system is not sure it recognized the number properly it responds Dial Number Please say yes or no followed by a tone If the number is correct say Yes The system responds with OK Sending Number and the dial tones are sent and the call continues Sending a Stored Name Tag During a Call 1 Press The system responds with Ready followed by a tone 2 Say Send name tag The system responds with Say a name tag to send tones followed by a tone 3 Say the
24. 3 33 Loading Your Vehicle 4 28 Locks Automatic Door Lock 2 8 Automatic Door Unlock 2 8 Delayed Locking 4 2 8 DOOF cctietiss teccetenateaniceddns 2 7 Lockout Protection 2 8 Power Door 0 0e0eees 2 8 Rear Door Security Locks 2 8 Loss of Control 055 4 12 Low Fuel Warning Light 3 41 Low Washer Fluid Warning LIQWE EEEE EEEE 3 40 Lower Anchors and Tethers for Children 2 0000 1 31 Luggage Carrier 0 2 43 Lumbar Manual Controls 1 5 M Maintenance FOOUINO1ES innast erria 6 8 Maintenance Schedule Additional Required ServiceS ccceeeee rio 6 6 At Each Fuel Fill 6 10 At Least Once a Month 6 10 At Least Once a Year 6 11 Maintenance Record 6 17 Maintenance Replacement Pars eein mea 6 15 Maintenance Requirements 6 1 Owner Checks and Services cccceee ee ee ee 6 10 Recommended Fluids and Lubricants 0 00 6 13 Scheduled Maintenance 6 3 USING sede cccteaetacenetaaact naasi 6 2 Your Vehicle and the Environment 20006 6 1 Malfunction Indicator Lamp 3 35 Manual Lumbar Controls 1 5 Manual Seats 00e 1 3 Message DIC Warnings and Messages isn 3 49 INDEX Mirrors Automatic Dimming Rearview 0ceeee eens Manual Rearview Mirror Outside
25. Aftermarket collision parts are also available These are made by companies other than GM and may not have been tested for your vehicle As a result these parts may fit poorly exhibit premature durability corrosion problems and may not perform properly in subsequent collisions Aftermarket parts are not covered by your GM New Vehicle Limited Warranty and Customer Assistance Information any vehicle failure related to such parts are not covered by that warranty Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs Your dealer retailer may have a collision repair center with GM trained technicians and state of the art equipment or be able to recommend a collision repair center that has GM trained technicians and comparable equipment Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage There are significant differences in the quality of coverage afforded by various insurance policy terms Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using 7 11 aftermarket collision parts Some insurance companies will not specify aftermarket collision parts When purchasing insurance we recommend that you assure your vehicle will be repaired with GM original equipment collision parts If such insurance
26. Battery fluid contains acid that can burn you Do not get it on you If you accidentally get it in your eyes or on your skin flush the place with water and get medical help immediately Z CAUTION Fans or other moving engine parts can injure you badly Keep your hands away from moving parts once the engine is running 5 Check that the jumper cables do not have loose or missing insulation If they do you could get a shock The vehicles could also be damaged Before you connect the cables here are some basic things you should know Positive will go to positive or to a remote positive terminal if the vehicle has one Negative will go toa heavy unpainted metal engine part or to a remote negative terminal if the vehicle has one Service and Appearance Care 5 33 Do not connect positive to negative or you will get a short that would damage the battery and maybe other parts Do not connect the negative cable to the negative terminal on the dead battery because this can cause sparks Connect the red positive cable to the positive terminal on the vehicle with the dead battery Use a remote positive terminal if the vehicle has one Do not let the other end touch metal Connect it to the positive terminal of the good battery Use a remote positive terminal if the vehicle has one 8 Now connect the black negative
27. Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying General Motors If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer retailer or General Motors Customer Assistance Information To contact NHTSA you may call the Vehicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 go to safercar gov or write to Administrator NHTSA 1200 New Jersey Avenue S E Washington D C 20590 You can also obtain other information about motor vehicle safety from safercar gov Reporting Safety Defects to the Canadian Government If you live in Canada and you believe that your vehicle has a safety defect notify Transport Canada immediately in addition to notifying General Motors of Canada Limited Call them at 1 800 333 0510 or write to Transport Canada Road Safety Branch 2780 Sheffield Road Ottawa Ontario KiB 3V9 Reporting Safety Defects to Saturn In addition to notifying NHTSA or Transport Canada in a situation like this please notify Saturn Cal
28. Do not race the engine immediately after starting it Operate the engine and transmission gently until the oil warms up and lubricates all moving parts Features and Controls Notice The engine is designed to work with the electronics in the vehicle If you add electrical parts or accessories you could change the way the engine operates Before adding electrical equipment check with your dealer retailer If you do not the engine might not perform properly Any resulting damage would not be covered by the vehicle warranty Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm up in cold weather conditions at or below 0 F 18 C Vehicles with an engine coolant heater should be plugged in at least four hours before starting Some models may have an internal thermostat in the cord which will prevent engine coolant heater operation at temperatures above O F 18 C To Use the Engine Coolant Heater 1 Turn off the engine 2 Open the hood and unwrap the electrical cord The engine coolant heater cord is located near the air cleaner box on the passenger side of the engine compartment See Engine Compartment Overview on page 5 12 for more information on location 3 Plug the cord into a normal grounded 110 volt AC outlet Z CAUTION Plugging the cord into an ungrounded outlet could cause an electrical shock Also the wrong
29. Indicator Light 3 1 3 2 Instrument Panel Engine Coolant Temperature 35 Warning Light ss irssiineenssssus 34 Tire Pressure Light 3 34 Malfunction Indicator Lamp seceeeeees 3 35 Oil Pressure Light 3 37 Change Engine Oil Light 3 38 Security Light sss iresssrssesss 3 38 Fog Lamp Light sccce0 tees 3 38 Cruise Control Light 3 38 Reduced Engine Power Light lt 2 cscstirsaecsntensen 3 39 Highbeam On Light 3 39 Daytime Running Lamps DRL Indicator Light 3 39 Low Washer Fluid Warning Light 0 3 40 All Wheel Drive Disabled Light 006 3 40 Gate Ajar Light eee 3 40 Door Ajar Light 666 3 40 Service Vehicle Soon Light 3 40 Fuel Gage is iecdeiancedetceadioines 3 41 Low Fuel Warning Light 3 41 Driver Information Center DIC Driver Information Center DIC c 0eeeeee 3 42 DIC Operation and Displays 3 42 DIC Compass 0cse0eeee 3 47 DIC Warnings and Messages sistein er 3 49 DIC Vehicle Customization 3 57 Audio System s Audio System s 3 64 Setting the Clock 66 3 65 RAdIO S sa aectnanetdiatanarimensen 3 67 Using an MP serseri 3 75 XM Radio Messages 3 79 Navigation Radio System 3 81 Bluetooth cceeeeeeeeeees 3 81 Theft Deterrent Feature 3 91 Audio Steering Wheel
30. Out of View See Checking Engine Oil under Engine Oil on page 5 14 F Automatic Transmission Fluid Dipstick Out of View See Checking the Fluid Level under Automatic Transmission Fluid on page 5 18 G Brake Fluid Reservoir Out of View See Brakes on page 5 28 H Engine Coolant Recovery Tank See Cooling System on page 5 19 I Remote Positive Terminal See Jump Starting on page 5 31 J See Underhood Fuse Block on page 5 82 K See Battery on page 5 30 L Windshield Washer Fluid Reservoir See Adding Washer Fluid under Windshield Washer Fluid on page 5 27 5 14 Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill In order to get an accurate reading the oil must be warm and the vehicle must be on level ground The engine oil dipstick handle is a yellow loop See Engine Compartment Overview on page 5 12 for the location of the engine oil dipstick 1 Turn off the engine and give the oil several minutes to drain back into the oil pan If this is not done the oil dipstick might not show the actual level 2 Pull the dipstick and clean it with a paper towel or cloth then push it back in all the way Remove it again keeping the tip down and check the level Service and Appearance Care When to Add Engine Oil If the oil is below the MIN minimum mark add at least one quart liter of the recommended oil This section explain
31. Secure objects away from the area in which an airbag would inflate For more information see Where Are the Airbags on page 1 45 and Loading the Vehicle on page 4 28 Things you put on this seatback can strike and injure people in a sudden stop or turn or in a crash Remove or secure all items before driving To fold the seatback 1 Lower the head restraint all the way 2 Lift the bar under the front of the seat to unlock it Slide the seat as far back as it will go and release the bar Try to move the seat back and forth to make sure it is locked into place 3 Lift the recliner lever located on the outboard side of the seat up fully and fold the seatback forward until it disengages Continue to fold the seat forward into the folded position Pull up on the seatback to be sure it is locked To raise the seatback 1 Lift the recliner lever located on the outboard side of the seat up fully and push up on the seatback 2 Continue raising the seatback until the seatback re engages Z CAUTION If either seatback is not locked it could move forward in a sudden stop or crash That could cause injury to the person sitting there Always push and pull on the seatbacks to be sure they are locked 3 Push and pull on the seatback to make sure it is locked in place The recliner lever is also used to recline the seatback while a passenger is seated
32. The performance may be reduced the next time the vehicle is driven The vehicle may be driven at a reduced speed while this message is on but acceleration and speed may be reduced Anytime this message stays on the vehicle should be taken to your dealer retailer for service as soon as possible FUEL LEVEL LOW This message displays when your vehicle is low on fuel Refill the fuel tank as soon as possible See Fuel Gage on page 3 41 and Filling the Tank on page 5 8 for more information HOOD OPEN If your vehicle has the remote start feature this message displays along with a chime when the hood is not closed properly Make sure that the hood is closed completely See Hood Release on page 5 11 This message displays while the ignition is in ON RUN Press any of the DIC buttons to acknowledge this message and to clear it from the screen This message continues to display for two seconds if it has not been acknowledged when the engine is turned off The message comes back on for two seconds if it has been acknowledged but the condition still exists when the engine is turned off If the condition still exists the message reappears when the engine is turned on ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions Adjust your driving accordingly LIFTGATE OPEN This message displays when the liftgate is not closed completely C
33. This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry RKE transmitter Press the customization button until PRESS V TO SET APPROACH LIGHTING appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings OFF The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter ON default If it is dark enough outside the exterior lights will turn on briefly when you unlock the vehicle with the RKE transmitter The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed or the vehicle is no longer off See Remote Keyless Entry RKE System Operation on page 2 4 for more information NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC CHIME VOLUME This feature allows you to select the volume level of the chime Press the customization button until PRESS V TO SET CHIME VOLUME appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings NORMAL The chime vol
34. correct cold tire inflation pressure for the vehicle load 5 51 Service and Appearance Care If your vehicle has P235 55R 18 size tires they will require inflation pressure adjustment when driving your vehicle at speeds of 100 mph 160 km h or higher Set the cold inflation pressure to the maximum inflation pressure shown on the tire sidewall or 38 psi 262 kPa whichever is lower See the example following When you end this high speed driving return the tires to the cold tire inflation pressure shown on the Tire and Loading Information label See Loading the Vehicle on page 4 28 and Inflation Tire Pressure on page 5 49 Example You will find the maximum load and inflation pressure molded on the tire s sidewall in small letters near the rim flange It will read something like this Maximum load 690 kg 1521 Ibs 300 kPa 44 psi Max Press For this example you would set the inflation pressure for high speed driving at 38 psi 262 kPa Tire Pressure Monitor System The Tire Pressure Monitor System TPMS uses radio and sensor technology to check tire pressure levels The TPMS sensors monitor the air pressure in your vehicle s tires and transmit tire pressure readings to a receiver located in the vehicle Each tire including the spare if provided should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle pla
35. during normal use as the original tires GM s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle including brake system performance ride and handling traction control and tire pressure Service and Appearance Care monitoring performance GM s TPC Spec number is molded onto the tire s sidewall near the tire size If the tires have an all season tread design the TPC Spec number will be followed by an MS for mud and snow See Tire Sidewall Labeling on page 5 44 for additional information GM recommends replacing tires in sets of four This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new Replacing less than a full set of tires can affect the braking and handling performance of your vehicle See Tire Inspection and Rotation on page 5 56 for information on proper tire rotation Z CAUTION Mixing tires could cause you to lose control while driving If you mix tires of different sizes brands or types radial and bias belted tires the vehicle may not handle properly and you could have a crash Using tires of different sizes brands or types may also cause damage to your vehicle Be sure to use the correct size brand and type of tires on all wheels It is all right to drive with your compact spare temporarily as it was developed for use on your
36. on page 1 31 for top tether anchor locations Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored or if the instructions that come with the child restraint say that the top strap must be anchored In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached Seats and Restraint System You will be using the lap shoulder belt to secure the child restraint in this position Follow the instructions that came with the child restraint 1 Move the seat as far back as it will go before securing the forward facing child restraint When the passenger sensing system has turned off the right front passenger frontal airbag the off indicator on the passenger airbag status indicator should light and stay lit when the vehicle is started See Passenger Airbag Status Indicator on page 3 30 2 Put the child restraint on the seat 3 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how z 4 Push the latch plate into the buckle until it clicks Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary 5 Pull the rest of the shoulder belt all the way out of the retractor to set the lock Seats
37. or Snow Sun Visors Sunroof Tachometer Taillamps Turn Signal Stoplamps and Back up Lamps Text Telephone TTY Users Theft Deterrent Feature Theft Deterrent Systems Content Theft Deterrent PASS Key Ill Electronic Immobilizer PASS Key Ill Electronic Immobilizer Operation Tilt Wheel Time Setting Tire Pressure Light Tires Aluminum Wheels Cleaning Buying New Tires Chains Changing a Flat Tire Cleaning sceeeeeeeneees Compact Spare Different Size High Speed Operation If a Tire Goes Flat Inflation Tire Pressure Inspection and Rotation Installing the Spare Tire Pressure Monitor Operation Pressure Monitor System Removing the Flat Tire Removing the Spare Tire and Tools Sidewall Labeling Storing a Flat or Spare Tire and Tools Terminology and Definitions Tires cont Uniform Tire Quality Grading wacctecacieccecstecadts 5 60 Wheel Alignment and Tire Balance 5 5 61 Wheel Replacement 5 62 When It Is Time for New Tires aaan 5 57 Towing Recreational Vehicle 4 32 Towing a Trailer 4 35 Your Vehicle 0e 4 32 Traction Control System TCS 4 8 Control System Warning Light ss cst caster idars 3 33 StabiliTrak System 4 7 Transmission Fluid Automatic 5 18 Transmission Operation Automatic 2 19
38. responds with Ready followed by a tone 2 After the tone say Mute Call The system responds with Resuming call Transferring a Call Audio can be transferred between the in vehicle Bluetooth system and the cell phone To Transfer Audio to the Cell Phone During a call with the audio in the vehicle 1 Press The system responds with Ready followed by a tone 2 Say Transfer Call The system responds with Transferring call and the audio will switch from the vehicle to the cell phone To Transfer Audio to the In Vehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred The connection process can take up to two minutes after the key is turned to the ON RUN or ACC ACCESSORY position During a call with the audio on the cell phone press for more than two seconds The audio switches from the cell phone to the vehicle Voice Pass Thru Voice Pass Thru allows access to the voice recognition commands on the cell phone See the cell phone manufacturers user guide to see if the cell phone supports this feature Instrument Panel 3 89 This feature can be used to verbally access contacts stored in the cell phone 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Bluetooth The system responds with Bluetooth ready
39. say Verify at any time and the system will repeat them Using the Call Command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Call The system responds with Call using lt phone name gt Please say the name tag followed by a tone 3 Say the name tag of the person to call e Ifthe system clearly recognizes the name tag it responds with OK calling lt name tag gt and dials the number e Ifthe system is unsure it recognizes the right name tag it confirms the name tag followed by a tone If the name tag is correct say Yes The system responds with OK calling lt name tag gt and dials the number If the name tag is not correct say No The system will ask for the name tag to be re entered Once connected the person called will be heard through the audio speakers Instrument Panel 3 87 Using the Re dial Command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 After the tone say Re dial The system responds with Re dial using lt phone name gt and dials the last number called from the connected Bluetooth phone Once connected the person called will be heard through the audio speakers Receiving a Call When an incoming call is received the audio system mutes and a ring tone is heard in the vehicle e Press and b
40. use only G TPC Spec Tire Performance Criteria Specification Original equipment tires designed to GM s specific tire performance criteria have a TPC specification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines 5 46 Tire Size The following illustration shows an example of a typical passenger vehicle tire size P225 60R16 97S TTT B CDE F A Passenger P Metric Tire The United States version of a metric tire sizing system The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U S Tire and Rim Association B Tire Width The three digit number indicates the tire section width in millimeters from sidewall to sidewall Service and Appearance Care C Aspect Ratio A two digit number that indicates the tire height to width measurements For example if the tire size aspect ratio is 60 as shown in item C of the illustration it would mean that the tire s sidewall is 60 percent as high as it is wide D Construction Code A letter code is used to indicate the type of ply construction in the tire The letter R means radial ply construction the letter D means diagonal or bias ply construction and the letter B means belted bias ply construction E Rim Diameter Diameter of the wheel in inches F Service Description These characters represent the load index and s
41. 28 for an example of the Tire and Loading Information label and its location on your vehicle Also see Inflation Tire Pressure on page 5 49 5 53 Your vehicle s TPMS system can warn you about a low tire pressure condition but it does not replace normal tire maintenance See Tire Inspection and Rotation on page 5 56 and Tires on page 5 43 Notice Liquid tire sealants could damage the Tire Pressure Monitor System TPMS sensors Sensor damage caused by using a tire sealant is not covered by your warranty Do not use liquid tire sealants TPMS Malfunction Light The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable When the system detects a malfunction the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle 5 54 Service and Appearance Care The TPMS malfunction light comes on at each ignition cycle until the problem is corrected Some of the conditions that can cause the malfunction light to come on are e One of the road tires has been replaced with the spare tire The spare tire does not have a TPMS sensor The TPMS malfunction light should go off once you re install the road tire containing the TPMS sensor e The TPMS sensor matching process was started but not completed or not completed successfully after rotating the vehicle s tires The TPMS malfunction light should go off once the TPMS sensor
42. 41 Cupholders 00cccseeeeeeee 2 41 Instrument Panel Storage 2 42 Sunglasses Storage Compartment ceeeeeeeee 2 42 Front Storage Area ceee 2 42 Center Console Storage 2 42 2 2 Features and Controls Luggage Carrier eseese 2 43 Rear Seat Armrest 2 44 Convenience Net esee 2 44 Cargo Cover scccsseeseeeeeeees 2 44 Cargo Tie Downs 0 2 44 Cargo Management SAC 2 44 Sunroof SUNrOO ss 2028 sivardecasiansteeesie 2 45 Keys Z CAUTION Leaving children in a vehicle with the ignition key is dangerous for many reasons children or others could be badly injured or even killed They could operate the power windows or other controls or even make the vehicle move The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window Do not leave the keys in a vehicle with children The two keys can be used for the ignition and all locks The key code is stamped on the key number plate and can be used to make new keys at any dealer retailer Store this information in a safe place outside the vehicle Notice f you ever lock your keys in the vehicle you may have to damage the vehicle to get in Be sure you have spare keys If you are locked out of the vehicle contact Roadside Assistance See Roadside Assistance Program on page 7 6 for more
43. 65 mph 105 km h is exceeded while towing the vehicle The repairs would not be covered by the vehicle warranty Never exceed 65 mph 105 km h while towing the vehicle Driving Your Vehicle 4 33 Once the destination has been reached 1 Set the parking brake 2 Shift the transmission to P Park 3 Reinstall the 2 amp IGN SW fuse to the instrument panel fuse block 4 Turn the ignition key to LOCK OFF and remove the key from the ignition Notice Too much or too little fluid can damage the transmission Be sure that the transmission fluid is at the proper level before towing with all four wheels on the ground Notice Do not tow a vehicle with the front drive wheels on the ground if one of the front tires is a compact spare tire Towing with two different tire sizes on the front of the vehicle can cause severe damage to the transmission 4 34 Driving Your Vehicle Dolly Towing All Wheel Drive Vehicles All wheel drive vehicles should not be towed with two wheels on the ground To properly tow these vehicles they should be placed on a platform trailer with all four wheels off of the ground or dinghy towed from the front Dolly Towing Front Wheel Drive Vehicles Front wheel drive VUE Red Line vehicles should not be towed with two wheels on the ground To properly tow these vehicles they should be placed on a platform trailer with all four wheels off of the ground or dinghy towed from
44. 8 Remove the flat tire Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after time The wheel could come off and cause an accident When changing a wheel remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if needed to get all the rust or dirt off See Changing a Flat Tire on page 5 64 Never use oil or grease on bolts or nuts because the nuts might come loose The vehicle s wheel could fall off causing a crash 10 Place the compact spare tire on the wheel mounting surface P fani 2 i lt 7 3 12 Lower the vehicle by turning the jack handle counterclockwise i i 1 aml 7 sin Ta 5 aie a 5 13 Tighten the wheel nuts firmly in a crisscross sequence as shown Z CAUTION Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off The wheel nuts should be Continued Service and Appearance Care CAUTION Continued tightened with a torque wrench to the proper torque specification after replacing Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts See Capacities and Specifications on page 5 86 for original equipment wheel nut torque s
45. Convex Mirror Outside Heated Mirrors Outside Power Mirrors MIPS oraina ar aO Navigation System Privacy Navigation Radio System see Navigation Manual Net Convenience New Vehicle Break In Odometer Odometer Trip eeeeeeeee Off Road Driving Recovery i 8 INDEX Oil Change Engine Oil Light Engine Engine Oil Life System Pressure Light Older Children Restraints Online Owner Center OnStar Privacy s OnStar System see OnStar Manual Operation Universal Home Remote System Outlet Adjustment Outlets Accessory Power Outside Convex Mirror Heated Mirrors Power Mirrors Owner Checks and Services Owners Canadian Paint Damage 255 Park Shifting Into Shifting Out of Parking Over Things That Burn Parking Brake scires Passenger Airbag Status Indicator Passenger Compartment Air Fiten gea are eae Passenger Sensing System Passing PASS Key Ill Electronic Immobilizer PASS Key Ill Electronic Immobilizer Operation Perchlorate Materials Requirements California Phone Bluetooth Power Door LOCKS 00eee eee Electrical System Reduced Engine Light Retained Accessory RAP Seat Steering Fluid Windows Power Steering Warning Lights Pregnancy Using Safety Belts Privacy Navigation System OnStar Radio Frequency Identif
46. Do this until the vehicle is held by the parking brake only e To check the P Park mechanism s holding ability With the engine running shift to P Park Then release the parking brake followed by the regular brake Contact your dealer retailer if service is required Underbody Flushing Service At least every spring use plain water to flush any corrosive materials from the underbody Take care to clean thoroughly any areas where mud and other debris can collect Maintenance Schedule 6 13 Recommended Fluids and Lubricants Fluids and lubricants identified below by name part number or specification can be obtained from your dealer retailer Usage O Fluid Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol To determine the proper viscosity for your vehicle s engine see Engine Oil on page 5 14 50 50 mixture of clean drinkable water and use only DEX COOL Engine Coolant Coolant See Engine Coolant on page 5 22 Engine Oil DOT 3 Hydraulic Brake Fluid GM Part No U S 12377967 Hydraulic Brake System in Canada 89021320 Windshield Washer Optikleen Washer Solvent MP ing Fluid GM Part No U S 89021184 Hydraulic Power Steering System z Camada TN are No Chassis Lubricant GM Part No 12377985 in Canada 88901242 or Parking Brake Cable Guides lubricant meeting requirements of NLGI 2 Catego
47. Driving on steep hills or through mountains is different than driving on flat or rolling terrain Tips for driving in these conditions include Keep the vehicle serviced and in good shape e Check all fluid levels and brakes tires cooling system and transmission e Going down steep or long hills shift to a lower gear Z CAUTION If you do not shift down the brakes could get so hot that they would not work well You would then have poor braking or even none going down a hill You could crash Shift down to let the engine assist the brakes on a steep downhill slope Z CAUTION Coasting downhill in N Neutral or with the ignition off is dangerous The brakes will have to do all the work of slowing down and they could get so hot that they would not work well You would then have poor braking or even none going down a hill You could crash Always have the engine running and the vehicle in gear when going downhill Stay in your own lane Do not swing wide or cut across the center of the road Drive at speeds that let you stay in your own lane Top of hills Be alert something could be in your lane stalled car accident Pay attention to special road signs falling rocks area winding roads long grades passing or no passing zones and take appropriate action Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires
48. Event arean E states Daytime Running Lamps DRL Daytime Running Lamps Indicator Light Defensive Driving 4 Delayed Locking DIC Compass iniiis nias Disc MP3 Doing Your Own Service Work Dome Lamp i 4 INDEX Door Ajar Light rrciscsczaassaescencccice Automatic Door Lock Automatic Door Unlock Delayed Locking Locks Power Door Locks Rear Door Security Locks Drive Systems All Wheel Drive Driver Seat Height Adjuster Driver Behavior Driver Information Center DIC DIC Operation and Displays DIC Vehicle Customization DIC Warnings and Messages Driving At Night Before a Long Trip Defensive Drunk Environment Highway Hypnosis Hill and Mountain Roads Driving cont In Rain and on Wet Roads Loss of Control Off Road Off Road Recovery Rocking Your Vehicle to Get it Out Winter Driving for Better Fuel ECONOMY s 2 ccdvdecesnetisea ce EDR cecateecectess EE Electrical Equipment Add On Equipment Electrical System Fuses and Circuit Breakers Instrument Panel Fuse Block Power Windows and Other Power Options Underhood Fuse Block Windshield Wiper Fuses Electronic Immobilizer PASS Key IIl Electronic Immobilizer Operation PASS Key Ill Engine Air Cleaner Filter Change Engine Oil Light Check and Service Engine Soon Lamp Compartment Overview Coolant Coolant Heater Coolant Tempera
49. For best performance or trailer towing you could choose to use middle grade 89 octane unleaded gasoline 5 6 If the octane rating is less than 87 you might notice an audible knocking noise when you drive commonly referred to as spark knock If this occurs use a gasoline rated at 87 octane or higher as soon as possible If you are using gasoline rated at 87 octane or higher and you hear heavy knocking the engine needs service Gasoline Specifications At a minimum gasoline should meet ASTM specification D 4814 in the United States or CAN CGSB 3 5 or 3 511 in Canada Some gasolines contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl MMT We recommend against the use of gasolines containing MMT See Additives on page 5 6 for additional information Service and Appearance Care California Fuel If the vehicle is certified to meet California Emissions Standards it is designed to operate on fuels that meet California specifications See the underhood emission control label If this fuel is not available in states adopting California emissions standards the vehicle will operate satisfactorily on fuels meeting federal specifications but emission control system performance might be affected The malfunction indicator lamp could turn on and the vehicle might fail a smog check test See Malfunction Indicator Lamp on page 3 35 If this occurs return to your authorized dealer r
50. Home Remote with any garage door opener that does not have the stop and reverse feature This includes any garage door opener model manufactured before April 1 1982 Read the instructions completely before attempting to program the Universal Home Remote Because of the steps involved it may be helpful to have another person available to assist you in the programming the Universal Home Remote Keep the original hand held transmitter for use in other vehicles as well as for future Universal Home Remote programming It is also recommended that upon the sale of the vehicle the programmed Universal Home Remote buttons should be erased for security purposes See Erasing Universal Home Remote Buttons later in this section Features and Controls When programming a garage door park outside of the garage Park directly in line with and facing the garage door opener motor head or gate motor head Be sure that people and objects are clear of the garage door or gate that is being programmed It is recommended that a new battery be installed in your hand held transmitter for quicker and more accurate transmission of the radio frequency signal Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System call 1 800 355 3515 or go to homelink com Programming a garage door opener involves time sensitive actions so read the entire procedure before starting Otherwi
51. If a CD is recorded on a personal computer and a description label is needed try labeling the top of the recorded CD with a marking pen To prevent contaminating the lens of the disc optics with lubricants internal to the player mechanism the use of disc lens cleaners is not advised Notice If a label is added to a CD or more than one CD is inserted into the slot at a time or an attempt is made to play scratched or damaged CDs the CD player could be damaged While using the CD player use only CDs in good condition without any label load one CD ata time and keep the CD player and the loading slot free of foreign materials liquids and debris If an error displays see CD Messages later in this section amp EJECT To eject the CD that is currently playing press and release this button A beep sounds and Ejecting Disc displays Once the disc is ejected Remove Disc displays The CD can be removed If the CD is not removed after several seconds the CD automatically pulls back into the player and begins playing For the Six Disc CD player press and hold ZS for two seconds to eject all discs J Tune Turn to select tracks on the CD currently playing K SEEK D Press the left arrow to go to the start of the current track if more than ten seconds have played Press the right arrow to go to the next track If either the left or right arrow is held or pressed multiple times the player continues mo
52. LATCH attachments rub against the vehicle s safety belts This may damage these parts If necessary move buckled safety belts to avoid rubbing the LATCH attachments Seats and Restraint System Do not fold the empty rear seat with a safety belt buckled This could damage the safety belt or the seat Unbuckle and return the safety belt to its stowed position before folding the seat 1 Attach and tighten the lower attachments to the lower anchors If the child restraint does not have lower attachments or the desired seating position does not have lower anchors secure the child restraint with the top tether and the safety belts Refer to your child restraint manufacturer instructions and the instructions in this manual 1 1 Find the lower anchors for the desired seating position 1 2 Put the child restraint on the seat 1 3 Attach and tighten the lower attachments on the child restraint to the lower anchors 1 35 2 If the child restraint manufacturer recommends that the top tether be attached attach and tighten the top tether to the top tether anchor if equipped Refer to the child restraint instructions and the following steps 2 1 Find the top tether anchor 2 2 Route attach and tighten the top tether according to your child restraint instructions and the following instructions If the position you are using does not have a headrest or head restraint and you are using a single tether rout
53. Negative Terminals C Dead Battery or Remote Positive Terminal To disconnect the jumper cables from both vehicles do the following 1 Disconnect the black negative cable from the vehicle that had the dead battery Disconnect the black negative cable from the vehicle with the good battery Disconnect the red positive cable from the vehicle with the good battery Disconnect the red positive cable from the other vehicle Return the underhood fuse block cover to its original position if applicable 5 35 Service and Appearance Care All Wheel Drive It is recommended that the all wheel drive lubricants be checked and filled by the dealer retailer Transfer Case When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it See Scheduled Maintenance on page 6 3 How to Check Lubricant T oe a f T i B Fi as A A Fill Plug B Drain Plug To get an accurate reading the vehicle should be on a level surface If the level is below the bottom of the filler plug hole located on the transfer case you ll need to add some lubricant Add enough lubricant to raise the level to the bottom of the filler plug hole A fluid loss could indicate a problem check and have it repaired if needed What to Use Refer to the Maintenance Schedule to determine what k
54. Programming Universal Home Remote to complete Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second The indicator light will come on while the signal is being transmitted Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends To erase all programmed buttons on the Universal Home Remote device 1 Press and hold down the two outside buttons until the indicator light begins to flash after 20 seconds 2 Release both buttons Features and Controls Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons repeat the programming instructions earlier in this section beginning with Step 2 For help or information on the Universal Home Remote System call the customer assistance phone number under Customer Assistance Offices on page 7 5 2 41 Storage Areas Glove Box To open the glove box lift up on the lever If the glove box has a lock use the key to lock and unlock it The glove box divider can be removed The slots on the left side are for storing the divider Cupholders There are cupholders located in front of and behind the center console To access the cupholders behind the center console push the button 2 42 Instrument Panel Storage Your vehicle has a storage area located to left of th
55. Putting a used wheel on your vehicle is dangerous You cannot know how it has been used or how far it has been driven It could fail suddenly and cause a crash If you have to replace a wheel use a new Saturn original equipment wheel Tire Chains Z CAUTION Do not use tire chains There is not enough clearance Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes suspension or other vehicle parts Continued CAUTION Continued The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions Follow that manufacturer s instructions To help avoid damage to the vehicle drive slowly readjust or remove the device if it is contacting the vehicle and do not spin the vehicle s wheels If you do find traction devices that will fit install them on the front tires Service and Appearance Care If a Tire Goes Flat It is unusual for a tire to blowout while you are driving especially if you maintain your vehicle s tires properly If air goes out of a tire itis much more likely to leak out slowly But if you should ever have a blowout here are a few tips about what to expect and what to do If a front tire fails the fl
56. Select the desired cabin air temperature between 60 90 F 16 32 C Choosing the coldest or warmest temperature setting does not cause the system to heat or cool any faster AUTO Automatic Air Delivery Mode Turn the air delivery mode knob to AUTO for the system to automatically control the direction of the airflow to help reach the desired inside temperature The system automatically controls the air inlet to supply the outside air or recirculated inside air needed to heat or cool the vehicle faster The recirculation button indicator light is lit whenever the recirculation mode is on Press the outside air button to change to outside air However the recirculation mode may turn back on automatically In cold weather if the fan and air delivery modes are in automatic the system starts at lower fan speeds to avoid directing cold air into the vehicle until warmer air is available The climate control system directs air to the floor but may automatically Instrument Panel 3 21 change modes as the vehicle warms up to maintain the chosen temperature setting The length of time needed to warm the interior depends on the outside temperature and inside temperature of the vehicle Manual Operation ss Fan Control Turn clockwise or counterclockwise to increase or decrease the fan speed To turn the fan off turn the left knob to the O position In any setting other than off the fan runs continuously wi
57. System Safety Belts Safety Belts They Are for Everyone This section of the manual describes how to use safety belts properly It also describes some things not to do with safety belts Z CAUTION Do not let anyone ride where a safety belt cannot be worn properly In a crash if you or your passenger s are not wearing safety belts the injuries can be much worse You can hit things inside the vehicle harder or be ejected from the vehicle You and your passenger s can be seriously injured or killed In the same crash you might not be if you are buckled up Always fasten your safety belt and check that your passenger s are restrained properly too Z CAUTION It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly This vehicle has indicators as a reminder to buckle the safety belts See Safety Belt Reminders on page 3 28 for additional information In most states and in all Canadian provinces the law requires wearing safety belts Here is why You never know if you will be in a crash If you do have a crash you do not know if it will be a serious one A few cr
58. TOLL FREE 1 800 551 4123 Monday Friday 8 00 AM 6 00 PM Eastern Time For Credit Card Orders Only VISA MasterCard Discover visit Helm Inc on the World Wide Web at helminc com Or you can write to Helm Incorporated P O Box 07130 Detroit MI 48207 Prices are subject to change without notice and without incurring obligation Allow ample time for delivery Note to Canadian Customers All listed prices are quoted in U S funds Canadian residents are to make checks payable in U S funds 7 16 Vehicle Data Recording and Privacy Your Saturn vehicle has a number of sophisticated computers that record information about the vehicle s performance and how it is driven For example your vehicle uses computer modules to monitor and control engine and transmission performance to monitor the conditions for airbag deployment and deploy airbags in a crash and if so equipped to provide antilock braking to help the driver control the vehicle These modules may store data to help your dealer retailer technician service your vehicle Some modules may also store data about how you operate the vehicle such as rate of fuel consumption or average speed These modules may also retain the owner s personal preferences such as radio pre sets seat positions and temperature settings Customer Assistance Information Event Data Recorders This vehicle has an Event Data Recorder EDR The main purpose of an E
59. a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is parked Tune to favorite stations using the presets favorites button and steering wheel controls if the vehicle has them See Defensive Driving on page 4 3 FAV Favorites A maximum of 36 stations can be programmed as favorites using the six pushbuttons positioned below the radio station frequency labels and by using the FAV button radio favorites page Press the FAV button to go through up to six pages of favorites each having six favorite stations available per page Each page of favorites can contain any combination of AM FM or XM stations To store a station as a favorite 1 Tune to the desired radio station 2 Press the FAV button to display the page where the station is to be stored 3 Press and hold one of the six pushbuttons until a beep sounds When that pushbutton is pressed and released the station that was set returns 4 Repeat the steps for each pushbutton radio station to be stored as a favorite The number of favorites pages can be setup using the MENU button To setup the number of favorites pages 1 Press the MENU button to display the radio setup menu 2 Press the pushbutton located below the FAV 1 6 label 3 Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers 4 Press the FAV button or let the menu time out
60. and or discontinue its participation in this program STEP THREE Canadian Owners General Motors Participation in the Mediation Arbitration Program In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2 General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory related vehicle service claims The program provides for the review of the facts involved by an impartial third party arbiter and may include an informal hearing before the arbiter The program is designed so that the entire dispute settlement process from the time you file your complaint to the 7 3 final decision should be completed in approximately 70 days We believe our impartial program offers advantages over courts in most jurisdictions because it is informal quick and free of charge For further information concerning eligibility in the Canadian Motor Vehicle Arbitration Plan CAMVAP call toll free 1 800 207 0685 Alternatively you may call the Saturn Customer Communication Centre 1 800 263 1999 or you may write to Mediation Arbitration Program c o Customer Communication Centre General Motors of Canada Limited Mail Code CA1 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Telephone 1 800 955 5100 Your inquiry should be accompanied by the Vehicle Identification Number VIN 7 4 Customer Assistance Inf
61. and run the engine for at least 10 minutes to allow the battery to recharge If the engine is running and the condition persists see your dealer retailer immediately CALIBRATING COMPASS TURN IN CIRCLES This message displays when calibrating the compass Drive the vehicle in circles at less than 5 mph 8 km h to complete the calibration See DIC Compass on page 3 47 CHANGE ENGINE OIL SOON This message displays when service is required for the vehicle See your dealer retailer See Engine Oil on page 5 14 and Scheduled Maintenance on page 6 3 for more information Acknowledging this message will not reset the OIL LIFE REMAINING display That must be done at the OIL LIFE screen See OIL LIFE under DIC Operation and Displays on page 3 42 and Engine Oil Life System on page 5 16 for more information CHANGE TRANSMISSION FLUID Notice Use of the incorrect automatic transmission fluid may damage the vehicle and the damages may not be covered by the vehicle s warranty Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 6 13 This message displays when the life of the transmission fluid has expired and it should be changed See Scheduled Maintenance on page 6 3 and Recommended Fluids and Lubricants on page 6 13 for the proper fluid and change intervals CHECK TIRE PRESSURE On vehicles with the Tire Pressure Monitor System TPMS this message disp
62. and the road creating less traction or grip Wet ice can occur at about 32 F 0 C when freezing rain begins to fall resulting in even less traction Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand Drive with caution whatever the condition Accelerate gently so traction is not lost Accelerating too quickly causes the wheels to spin and makes the surface under the tires slick so there is even less traction Try not to break the fragile traction If you accelerate too fast the drive wheels will spin and polish the surface under the tires even more Driving Your Vehicle 4 25 The Antilock Brake System ABS on page 4 6 improves vehicle stability during hard stops on a slippery roads but apply the brakes sooner than when on dry pavement Allow greater following distance on any slippery road and watch for slippery spots Icy patches can occur on otherwise clear roads in shaded areas The surface of a curve or an overpass can remain icy when the surrounding roads are clear Avoid sudden steering maneuvers and braking while on ice Turn off cruise control if equipped on slippery surfaces 4 26 Blizzard Conditions Being stuck in snow can be ina serious situation Stay with the vehicle unless there is help nearby If possible use the Roadside Assistance Program on page 7 6 To get help and keep everyone in the vehicle safe e Turn on the Hazard Warning Flash
63. are all important It can depend on any special equipment on the vehicle and the amount of tongue weight the vehicle can carry See Weight of the Trailer Tongue later in this section for more information Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required trailering equipment The weight of additional optional equipment passengers and cargo in the tow vehicle must be subtracted from the maximum trailer weight Look in the following chart to find the maximum trailer weight for the vehicle Max Trailer Wt GCWR 2WD 2 4L L4 Engine 1 500 Ibs 680 kg 5 375 Ibs 2 438 kg 3 500 Ibs 1 588 kg 7 800 Ibs 3 538 kg 2WD 3 6L V6 Engine AWD 3 5L V6 Engine 3 500 Ibs 1 588 kg AWD 3 6L V6 Engine 3 500 Ibs 1 588 kg 8 000 Ibs 3 629 kg 8 000 Ibs 3 629 kg The Gross Combination Weight Rating GCWR is the total allowable weight of the completely loaded vehicle and trailer including any passengers cargo equipment and conversion The GCWR for the vehicle should not be exceeded The VUE Red Line should not be used to tow a trailer Ask your dealer retailer for trailering information or advice 4 38 Weight of the Trailer Tongue The tongue load A of any trailer is an important weight to measure because it affects the total gross weight of the vehicle The Gross Vehicle Weight GVW includes the curb weight of
64. as possible while still maintaining control of the vehicle Occupants should not lean on or sleep against the door or side windows in seating positions with seat mounted side impact airbags and or roof rail airbags 1 44 Seats and Restraint System Z CAUTION CAUTION Continued Children who are up against or very close to any airbag when it inflates can be seriously injured or killed Airbags plus lap shoulder belts offer protection for adults and older children but not for young children and infants Neither the vehicle s safety belt system nor its airbag system is Continued designed for them Young children and infants need the protection that a child restraint system can provide Always secure children properly in your vehicle To read how see Older Children on page 1 23 or Infants and Young Children on page 1 26 rt There is an airbag readiness light on the instrument panel cluster which shows the airbag symbol The system checks the airbag electrical system for malfunctions The light tells you if there is an electrical problem See Airbag Readiness Light on page 3 29 for more information Where Are the Airbags The driver frontal airbag is in the middle of the steering wheel Seats and Restraint System 1 45 The right front passenger frontal airbag is in the instrument panel on the passenger side Driver Side shown P
65. at the same time In many emergencies steering can help more than even the very best braking StabiliTrak System The vehicle has a vehicle stability enhancement system called StabiliTrak which combines antilock brake traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions StabiliTrak activates when the computer senses a discrepancy between the intended path and the direction the vehicle is actually traveling StabiliTrak selectively applies braking pressure at any one of the vehicle s brakes to assist the driver with keeping the vehicle on the intended path When the vehicle is started and begins to move the system performs several diagnostic checks to insure there are no problems The system may be heard or felt while it is working This is normal and does not mean there is a problem with the vehicle AN ee This light is located on the instrument panel cluster It will flash when StabiliTrak is both on and activated If the system fails to turn on or activate this light will be on solid When the light is on solid the system will not assist the driver maintain directional control of the vehicle Adjust your driving accordingly The StabiliTrak system automatically comes on whenever the vehicle is started To assist the driver with vehicle directional control especially in slippery road conditions the system should always
66. backfire can cause a damaging engine fire And dirt can easily get into the engine which will damage it Always have the air cleaner filter in place when you are driving Automatic Transmission Fluid It is not necessary to check the transmission fluid level A transmission fluid leak is the only reason for fluid loss If a leak occurs take your vehicle to the dealer retailer and have it repaired as soon as possible Change the fluid and filter at the intervals listed in Additional Required Services on page 6 6 and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 6 13 Notice Use of the incorrect automatic transmission fluid may damage the vehicle and the damages may not be covered by the vehicle s warranty Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 6 13 For the 2 4L 3 5L and 3 6L engines the transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature If you need to check the transmission fluid level please take your vehicle to your dealer retailer Service and Appearance Care Cooling System When you decide it is safe to lift the hood here is what you will see 2 4L L4 Engine shown 3 5L V6 and 3 6L V6 Engines similar A Electric Engine Fan B Coolant Surge Tank C Pressure Cap 5 19 Z CAUTION An electric engine cooling fan under th
67. be anchored or if the instructions Seats and Restraint System that come with the child restraint say that the top strap must be anchored In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached If the child restraint does not have the LATCH system you will be using the safety belt to secure the child restraint in this position Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say If more than one child restraint needs to be installed in the rear seat be sure to read Where to Put the Restraint on page 1 30 1 Put the child restraint on the seat 2 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how 1 37 J N 3 Push the latch plate into the buckle until it clicks Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary 1 38 Seats and Restraint System 4 Pull the rest of the shoulder belt all the way out of the retractor to set the lock To tighten the belt push down on the child restraint pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor When installing a forward facing child
68. be connected to the auxiliary input jack for use as another source for playing CDs Press the CD AUX button again and the system begins playing audio from the connected portable audio player If a portable audio player is not connected No Input Device Found displays Playing an MP3 CD R or CD RW Disc The vehicle s radio system may have the MP3 feature If it has this feature it is capable of playing an MP3 CD R or CD RW disc For more information on how to play an MP3 CD R or CD RW disc see Using an MP3 on page 3 75 later in this section 3 74 Instrument Panel CD Messages CHECK DISC If this message displays and or the CD comes out it could be e It is very hot When the temperature returns to normal the CD should play e The road is very rough When the road becomes smoother the CD should play e The CD is dirty scratched wet or upside down e The air is very humid If so wait about an hour and try again e There could have been a problem while burning the CD e The label could be caught in the CD player If the CD is not playing correctly for any other reason try a known good CD If any error occurs repeatedly or if an error cannot be corrected contact your dealer retailer If the radio displays an error message write it down and provide it to your dealer retailer when reporting the problem Using the Auxiliary Input Jack The radio system has an auxiliary input jack
69. belt that is not properly worn may not provide the protection needed in a crash The person wearing the belt could be seriously injured The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces 4 Buckle position and release the safety belt as described previously in this section Make sure that the shoulder belt crosses the shoulder To remove and store the comfort guide squeeze the belt edges together so that the safety belt can be removed from the guide Store the comfort guide in its storage location which is a pocket on the side of the seat Safety Belt Use During Pregnancy Safety belts work for everyone including pregnant women Like all occupants they are more likely to be seriously injured if they do not wear safety belts A pregnant woman should wear a lap shoulder belt and the lap portion should be worn as low as possible below the rounding throughout the pregnancy Seats and Restraint System The best way to protect the fetus is to protect the mother When a safety belt is worn properly it is more likely that the fetus will not be hurt in a crash For pregnant women as for anyone the key to making safety belts effective is wearing them properly Safety Belt Extender If the vehicle s safety belt will fasten around you you should use it But if a safety belt is not long enough you
70. can cause premature engine heater core or radiator corrosion In addition the engine coolant may require changing sooner at the first maintenance service after each 30 000 miles 50 000 km or 24 months whichever occurs first Any repairs would not be covered by the vehicle warranty Always use DEX COOL silicate free coolant in the vehicle Service and Appearance Care What to Use Use a mixture of one half clean drinkable water and one half DEX COOL coolant which will not damage aluminum parts If you use this coolant mixture you do not need to add anything else Z CAUTION Adding only plain water to the cooling system can be dangerous Plain water or some other liquid such as alcohol can boil before the proper coolant mixture will The vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture the engine could get too hot but you would not get the overheat warning The engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant 5 23 Notice If an improper coolant mixture is used the engine could overheat and be badly damaged The repair cost would not be covered by the vehicle warranty Too much water in the mixture can freeze and crack the engine radiator heater core and other parts If you have to add coolant more than four times a year have your
71. can cause your brakes to overheat and fade This could cause loss of control and a serious accident Apply the brakes lightly when descending a hill and use a low gear to keep vehicle speed under control 4 20 Driving Your Vehicle Things not to do when driving down a hill e When driving downhill avoid turns that take you across the incline of the hill A hill that is not too steep to drive down might be too steep to drive across The vehicle could roll over e Never go downhill with the transmission in N Neutral called free wheeling The brakes will have to do all the work and could overheat and fade Vehicles are much more likely to stall when going uphill but if it happens when going downhill 1 Stop the vehicle by applying the regular brakes and apply the parking brake 2 Shift to P Park and while still braking restart the engine Shift back to a low gear release the parking brake and drive straight down If the engine will not start get out and get help Driving Across an Incline An off road trail will probably go across the incline of a hill To decide whether to try to drive across the incline consider the following Z CAUTION Driving across an incline that is too steep will make your vehicle roll over You could be seriously injured or killed If you have any doubt about the steepness of the incline do not drive across it Find another route instead
72. clean inside and out e Keep your eyes moving especially during turns or curves No one can see as well at night as in the daytime But as we get older these differences increase A 50 year old driver might need at least twice as much light to see the same thing at night as a 20 year old Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate Always drive slower in these types of driving conditions and avoid driving through large puddles and deep standing or flowing water Z CAUTION Wet brakes can cause crashes They might not work as well in a quick stop and could cause pulling to one side You could lose control of the vehicle After driving through a large puddle of water or a car vehicle wash lightly apply the brake pedal until the brakes work normally Flowing or rushing water creates strong forces Driving through flowing water could cause your vehicle to be carried away If this happens you and other vehicle occupants could drown Do not ignore police warnings and be very cautious about trying to drive through flowing water Driving Your Vehicle 4 23 Hydroplaning Hydroplaning is dangerous Water can build up under your vehicle s tires so they actually ride on the water This can happen if the road is wet enough and you are going fast enough When your vehicle is hydroplaning it has little
73. clean by washing it often Notice Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle Check the cleaning product label If it states that it should not be used on plastic parts do not use it on the vehicle or damage may occur and it would not be covered by the warranty Service and Appearance Care Do not wash the vehicle in direct sunlight Use a car washing soap Do not use cleaning agents that are petroleum based or that contain acid or abrasives as they can damage the paint metal or plastic on the vehicle Approved cleaning products can be obtained from your dealer retailer Follow all manufacturers directions regarding correct product usage necessary safety precautions and appropriate disposal of any vehicle care product Rinse the vehicle well before washing and after to remove all cleaning agents completely If they are allowed to dry on the surface they could stain Dry the finish with a soft clean chamois or an all cotton towel to avoid surface scratches and water spotting 5 75 High pressure car washes may cause water to enter the vehicle Avoid using high pressure washes closer than 12 inches 30 cm to the surface of the vehicle Use of power washers exceeding 1 200 psi 8 274 kPa can result in damage or removal of paint and decals Cleaning Exterior Lamps Lenses Use only lukewarm or cold water a soft cloth and a car washing soap to clean e
74. come on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer This light along with the service engine soon light displays when a noticeable reduction in the vehicle s performance occurs Stop the vehicle and turn off the ignition Wait for 10 seconds and restart the vehicle This might correct the condition The vehicle can be driven at a reduced speed when the reduced engine power light is on but acceleration and speed might be reduced The performance could be reduced until the next time the vehicle is driven If this light stays on see your dealer retailer as soon as possible for diagnosis and repair Highbeam On Light D The highbeam on light comes on when the high beam headlamps are in use See Headlamp High Low Beam Changer on page 3 7 for more information Instrument Panel 3 39 Daytime Running Lamps DRL Indicator Light SO This light turns on whenever the Daytime Running Lamps are on See Daytime Running Lamps DRL on page 3 13 for more information 3 40 Instrument Panel Low Washer Fluid Warning Light The low washer fluid warning light comes on when the windshield washer fluid is low See Windshield Washer Fluid on page 5 27 for more information All Wheel Drive Disabled Light This light comes on when there is a malfunction in the All Wheel Drive AWD system This light flashes when the AWD system is temporarily di
75. contain lead and lead compounds chemicals known to the State of California to cause cancer and reproductive harm Wash hands after handling Vehicle Storage Z CAUTION Batteries have acid that can burn you and gas that can explode You can be badly hurt if you are not careful See Jump Starting on page 5 37 for tips on working around a battery without getting hurt Infrequent Usage If the vehicle is driven infrequently remove the black negative cable from the battery This helps keep the battery from running down Extended Storage For extended storage of the vehicle remove the black negative cable from the battery or use a battery trickle charger This helps maintain the charge of the battery over an extended period of time Jump Starting If the vehicle battery has run down you may want to use another vehicle and some jumper cables to start your vehicle Be sure to use the following steps to do it safely Z CAUTION Batteries can hurt you They can be dangerous because e They contain acid that can burn you e They contain gas that can explode or ignite e They contain enough electricity to burn you If you do not follow these steps exactly some or all of these things can hurt you Notice Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty Service and Appearance Care Trying to start the
76. cycles B High For rapid wiping cycles Clear ice and snow from the wiper blades before using them If the wiper blades are frozen to the windshield gently loosen or thaw them 3 8 Instrument Panel If they become damaged install new blades or blade inserts See Windshield Wiper Blade Replacement on page 5 42 Heavy snow or ice can overload the wiper motor A circuit breaker will stop the motor until it cools down Rainsense Il Wipers For vehicles with Rainsense II windshield wipers the moisture sensor is located next to the inside rearview mirror and is mounted on the windshield When active these sensors are able to detect moisture on the windshield and automatically turn on the wipers To turn on the Rainsense feature the wipers must be set to one of the five delay settings on the multifunction lever Each of the five settings adjusts the sensitivity of the sensor Since different drivers have different setting preferences it is recommended that the mid range setting position 3 be used initially For more wipes select the higher settings for fewer wipes select the lower settings located closer to the off position on the multifunction lever The sensor will automatically control the frequency of the wipes from the off setting to the high speed setting according to the weather conditions The wipers can be left in a rainsense mode even when it is not raining When Rainsense is activ
77. damage the surface of the wheel s The repairs would not be covered by the vehicle warranty Use only approved cleaners on aluminum or chrome plated wheels Service and Appearance Care Keep the wheels clean using a soft clean cloth with mild soap and water Rinse with clean water After rinsing thoroughly dry with a soft clean towel A wax may then be applied Notice Using chrome polish on aluminum wheels could damage the wheels The repairs would not be covered by the vehicle warranty Use chrome polish on chrome wheels only The surface of these wheels is similar to the painted surface of the vehicle Do not use strong soaps chemicals abrasive polishes abrasive cleaners cleaners with acid or abrasive cleaning brushes on them because the surface could be damaged Do not use chrome polish on aluminum wheels 5 77 Notice Driving the vehicle through an automatic car wash that has silicone carbide tire cleaning brushes could damage the aluminum or chrome plated wheels The repairs would not be covered by the vehicle warranty Never drive a vehicle that has aluminum or chrome plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes Tires To clean the tires use a stiff brush with tire cleaner Notice Using petroleum based tire dressing products on the vehicle may damage the paint finish and or tires When applying a tire dressing always wipe off any overs
78. following fixed bit rates 32 kbps 40 kbps 56 kbps 64 kbps 80 kbps 96 kbps 112 kbps 128 kbps 160 kbps 192 kbps 224 kbps 256 kbps and 320 kbps or a variable bit rate Song title artist name and album are available for display by the radio when recorded using ID3 tags version 1 and 2 Compressed Audio The radio also plays discs that contain both uncompressed CD audio CDA files and MP3 files By default the radio reads only the uncompressed audio and ignore the MP3 files Pressing the CAT category button toggles between compressed and uncompressed audio format MP3 Format To burn an MP3 disc on a personal computer e Make sure the MP3 files are recorded on a CD R or CD RW disc e Do not mix standard audio and MP3 files on one disc e The CD player is able to read and play a maximum of 50 folders 50 playlists and 255 files e Create a folder structure that makes it easy to find songs while driving Organize songs by albums using one folder for each album Each folder or album should contain 18 songs or less e Avoid subfolders The system can support up to eight subfolders deep however keep the total number of folders to a minimum in order to reduce the complexity and confusion in trying to locate a particular folder during playback Instrument Panel 3 75 Make sure playlists have a mp3 or wpl extension other file extensions may not work Minimize the length of the file fo
79. in this manual for more information Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers vehicle convenience accessories and external electronic devices are plugged into the accessory power outlet If there is interference or static unplug the item from the accessory power outlet AM The range for most AM stations is greater than for FM especially at night The longer range can cause station frequencies to interfere with each other For better radio reception most AM radio stations boost the power levels during the day and then reduce these levels during the night Static can also occur when things like storms and power lines interfere with radio reception When this happens try reducing the treble on the radio FM Stereo FM signals only reach about 10 to 40 miles 16 to 65 km Although the radio has a built in electronic circuit that automatically works to reduce interference some static can occur especially around tall buildings or hills causing the sound to fade in and out XM Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast to coast in the 48 contiguous United States and in Canada Just as with FM tall buildings or hills can interfere with satellite radio signals causing the sound to fade in and out In addition traveling or standing under heavy foliage bridges garag
80. instrument panel cluster The traction control system can be turned back on by pressing the TCS StabiliTrak button If the system is limiting wheel spin when the button is pressed the system will not turn off until there is no longer a current need to limit wheel spin The system can be turned back on at any time by pressing the button again If the TCS light does not come on TCS may not be functioning properly and the vehicle should be serviced at your dealer retailer Adding non dealer non retailer accessories can affect the vehicle s performance See Accessories and Modifications on page 5 3 for more information All Wheel Drive AWD System If the vehicle has all wheel drive AWD the AWD system operates automatically without any action required by the driver If the front drive wheels begin to slip the rear wheels will automatically begin to drive the vehicle as required There may be a slight engagement noise during hard use but this is normal This light is located on the instrument panel cluster It will come on and stay on to indicate there may be a problem with the drive system and service is required If the light stays on it must be reset To reset the light turn the ignition off and then back on again If the light stays on see your dealer retailer for service Driving Your Vehicle 4 9 If the vehicle is exposed to extended heavy AWD usage the AWD system will shut off to protect the sys
81. lamp bulb see Front Turn Signal and Parking Lamps on page 5 40 1 Open the hood See Hood Release on page 5 11 for more information 2 Remove the two screws from the top of the front fascia and grille They are inboard of the headlamp assembly 3 Remove the three screws retaining the headlamp assembly 4 Insert a flat blade tool through the opening in the top Make sure the tool fits through the opening in the headlamp bracket lower arm 5 Push the locking tab toward the rear of the vehicle with the tool to lift the headlamp bracket lower arm 5 39 6 Pull back on the front fascia and then pull the headlamp assembly out from the vehicle Another person might be needed to assist with this step 7 Disconnect the electrical connector from the bulb assembly 8 Turn the bulb assembly counterclockwise to remove it from the housing 9 Replace the old bulb with a new one 10 Reverse Steps 1 through 8 to reinstall 5 40 Front Turn Signal and Parking Lamps To replace a front turn signal or parking lamp bulb 1 Follow Steps 1 through 6 under Headlamps on page 5 39 to access the front turn signal or parking lamp 2 Turn the bulb to be replaced counterclockwise to remove it from the headlamp assembly 3 4 Service and Appearance Care Pull the bulb out of the bulb socket assembly Push the new bulb into the bulb socket assembly Insert the bulb assembly into the headla
82. little too hot when you e Climb a long hill on a hot day Stop after high speed driving e Idle for long periods in traffic e Tow a trailer 5 26 Service and Appearance Care If you get the overheat warning with no sign of steam try this for a minute or so 1 If you have an air conditioner and it is on turn it off 2 Turn on your heater to full hot at the highest fan speed and open the windows as necessary 3 Try to minimize engine load If you are in a traffic jam shift to N Neutral otherwise shift to the highest gear possible while driving If you no longer have the overheat warning you can drive Just to be safe drive slower for about ten minutes If the warning does not come back on you can drive normally If the warning continues and you have not stopped pull over stop and park your vehicle right away If there is still no sign of steam idle the engine for three minutes while you are parked If the warning continues turn off the engine and get everyone out of the vehicle until it cools down You may decide not to lift the hood but to get service help right away Power Steering Fluid a iai i titi Lo See Engine Compartment Overview on page 5 12 for reservoir location When to Check Power Steering Fluid Power steering fluid is used in all vehicles with V6 engines Vehicles with the 4 cylinder engine have electric power steering and does not use po
83. located on the lower right side of the faceplate This is not an audio output do not plug the headphone set into the front auxiliary input jack An external audio device such as an iPod laptop computer MP3 player CD changer etc can be connected to the auxiliary input jack for use as another audio source Drivers are encouraged to set up any auxiliary device while the vehicle is in P Park See Defensive Driving on page 4 3 for more information on driver distraction To use a portable audio player connect a 3 5 mm 1 8 inch cable to the radio s front auxiliary input jack When a device is connected press the radio CD AUX button to begin playing audio from the device over the vehicle speakers D Power Volume Turn to increase or decrease the volume of the portable player Additional volume adjustments might have to be made from the portable device if the volume is not loud or soft enough BAND Press to listen to the radio when a portable audio device is playing The portable audio device continues playing CD AUX CD Auxiliary Press to play a CD when a portable audio device is playing Press again and the system begins playing audio from the connected portable audio player If a portable audio player is not connected No Input Device Found displays Using an MP3 MP3 CD R or CD RW Disc The radio plays MP3 files that were recorded on a CD R or CD RW disc The files can be recorded with the
84. location based weather local traffic reports and stock quotes Press the phone button and give a few simple voice commands to browse through the various topics See the OnStar Owner s Guide for more information This feature is only available in the continental U S OnStar Steering Wheel Controls This vehicle may have a Talk Mute button that can be used to interact with OnStar Hands Free Calling See Audio Steering Wheel Controls on page 3 92 for more information OnStar voice command does not work unless Personal Calling is activated To activate Personal Calling see the OnStar Owner s Guide 2 36 On some vehicles the mute button can be used to dial numbers into voice mail systems or to dial phone extensions See the OnStar Owner s Guide for more information How OnStar Service Works The OnStar system can record and transmit vehicle information This information is automatically sent to an OnStar Call Center when the OnStar button is pressed the emergency button is pressed or if the airbags or AACN system deploy This information usually includes the vehicle s GPS location and in the event of a crash additional information regarding the crash that the vehicle was involved in e g the direction from which the vehicle was hit When the Virtual Advisor feature of OnStar Hands Free Calling is used the vehicle also sends OnStar the vehicle s GPS location so they can provide services where it is locate
85. m Not all phones support all functions and not all phones are guaranteed to work with the in vehicle Bluetooth system See gm com bluetooth for more information on compatible phones Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags Noise Keep interior noise levels to a minimum The system may not recognize voice commands if there is too much background noise When to Speak A short tone sounds after the system responds indicating when it is waiting for a voice command Wait until the tone and then speak How to Speak Speak clearly in a calm and natural voice Audio System When using the in vehicle Bluetooth system sound comes through the vehicle s front audio system speakers and overrides the audio Instrument Panel 3 81 system Use the audio system volume knob during a call to change the volume level The adjusted volume level remains in memory for later calls To prevent missed calls a minimum volume level is used if the volume is turned down too low Bluetooth Controls Use the buttons located on the steering wheel to operate the in vehicle Bluetooth system See Audio Steering Wheel Controls on page 3 92 for more information v Push To Talk Press to answer incoming calls confirm system information and to start speech recognition Phone On Hook Press to end a call and to cancel an
86. make it easier for others to see the front of your vehicle during the day Fully functional daytime running lamps are required on all vehicles first sold in Canada The DRL system makes the low beam headlamps come on in daylight when the following conditions are met e The engine is running e The exterior lamp band is in AUTO and The light sensor determines it is daytime When the DRL are on the low beam headlamps will be on The taillamps sidemarker instrument panel lights and other lamps will not be on When the exterior lamp band is turned to the headlamp position the regular headlamps will come on The other lamps that come on with the headlamps will also come on When the headlamps are turned off the regular lamps also turn off and the low beam headlamps turn on The regular headlamp system should be used when needed Instrument Panel 3 13 Automatic Headlamp System When it is dark enough outside the headlamps come on automatically at a There is a light sensor located on top of the instrument panel Do not cover the sensor or the headlamps will come on when they are not needed The system may also turn on the headlamps when driving through a parking garage or tunnel 3 14 Instrument Panel Fog Lamps For vehicles with fog lamps the button is located on the instrument panel next to the exterior lamps switch 40 Press to turn the fog lamps on or off The fog lamp i
87. name of the phone to be deleted If the phone name is unknown use the List command for a list of all paired phones The system responds with Would you like to delete lt phone name gt Yes or No followed by a tone 5 Say Yes to delete the phone The system responds with OK deleting lt phone name gt Linking to a Different Phone 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Bluetooth The system responds with Bluetooth ready followed by a tone Instrument Panel 3 83 3 Say Change phone The system responds with Please wait while search for other phones e If another phone is found the response will be lt Phone name gt is now connected If another phone is not found the original phone remains connected Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems The system uses the following commands to store and retrieve phone numbers e Store e Digit Store e Directory 3 84 Instrument Panel Using the Store Command The store command allows a phone number to be stored without entering the digits individually 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Store The system responds with Store number please followe
88. name tag to send e If the system clearly recognizes the name tag it responds with OK Sending lt name tag gt and the dial tones are sent and the call continues e Ifthe system is not sure it recognized the name tag properly it responds Dial lt name tag gt Please say yes or no followed by a tone If the name tag is correct say Yes The system responds with OK Sending lt name tag gt and the dial tones are sent and the call continues Clearing the System Unless information is deleted out of the in vehicle Bluetooth system it will be retained indefinitely This includes all saved name tags in the phonebook and phone pairing information For information on how to delete this information see the above sections on Deleting a Paired Phone and Deleting Name Tags Other Information The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by General Motors is under license Other trademarks and trade names are those of their respective owners This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device m
89. of the safety belt assembly They can help tighten the safety belts during the early stages of a moderate to severe frontal near frontal or rear crash if the threshold conditions for pretensioner activation are met And for vehicles with side impact airbags safety belt pretensioners can help tighten the safety belts in a side crash or a rollover event Pretensioners work only once If the pretensioners activate in a crash they will need to be replaced and probably other new parts for the vehicle s safety belt system See Replacing Restraint System Parts After a Crash on page 1 59 Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults When installed on a shoulder belt the comfort guide positions the shoulder belt away from the neck and head 1 21 There is one guide for each outboard passenger position in the rear seat Here is how to install a comfort guide to the safety belt 1 Remove the guide from its storage location which is a pocket on the side of the seat k Wh 4 We gt 2 Place the guide over the belt and insert the two edges of the belt into the slots of the guide 1 22 Lt 3 Be sure that the belt is not twisted and it lies flat The elastic cord must be under the belt and the guide on top Seats and Restraint System Z CAUTION A safety
90. operation 3 82 Instrument Panel Pairing A Bluetooth enabled cell phone must be paired to the in vehicle Bluetooth system first and then connected to the vehicle before it can be used See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone Ifa Bluetooth phone is not connected calls will be made using OnStar Hands Free Calling if available Refer to the OnStar owner s guide for more information Pairing Information e Up to five cell phones can be paired to the in vehicle Bluetooth system e The pairing process is disabled when the vehicle is moving e The in vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired e Only one paired cell phone can be connected to the in vehicle Bluetooth system at a time e Pairing should only need to be completed once unless changes to the pairing information have been made or the phone is deleted To link to a different paired phone see Linking to a Different Phone later in this section Pairing a Phone 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Bluetooth The system responds with Bluetooth ready followed by a tone 3 Say Pair The system responds with instructions and a four digit PIN number The PIN number will be used in Step 4 Start the Pairing process
91. or no contact with the road There is no hard and fast rule about hydroplaning The best advice is to slow down when the road is wet Other Rainy Weather Tips Besides slowing down other wet weather driving tips include Allow extra following distance Pass with caution Keep windshield wiping equipment in good shape Keep the windshield washer fluid reservoir filled Have good tires with proper tread depth See Tires on page 5 43 Turn off cruise control 4 24 Driving Your Vehicle Before Leaving on a Highway Hypnosis Long Trip Always be alert and pay attention To prepare your vehicle for a long to your surroundings while driving trip consider having it serviced by If you become tired or sleepy find your dealer retailer before departing e to park your vehicle Things to check on your own l haida Other driving tips include e Windshield Washer Fluid e Keep the vehicle well ventilated Reservoir full Windows e Keep interior temperature cool insi ide i clean inside and outside Keep your eyes moving scan e Wiper Blades In good shape the road ahead and to the sides e Fuel Engine Oil Other Fluids All e Check the rearview mirror and levels checked vehicle instruments often e Lamps Do they all work and are lenses clean e Tires Are treads good Are tires inflated to recommended pressure e Weather and Maps Safe to travel Have up to date maps Hill and Mountain Roads
92. production options weight Normal Occupant Weight The number of occupants a vehicle is designed to seat multiplied by 150 Ibs 68 kg See Loading the Vehicle on page 4 28 Occupant Distribution Designated seating positions Outward Facing Sidewall The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle The side of the tire that contains a whitewall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire Service and Appearance Care Passenger P Metric Tire A tire used on passenger cars and some light duty trucks and multipurpose vehicles Recommended Inflation Pressure Vehicle manufacturer s recommended tire inflation pressure as shown on the tire placard See Inflation Tire Pressure on page 5 49 and Loading the Vehicle on page 4 28 Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread Rim A metal support for a tire and upon which the tire beads are seated Sidewall The portion of a tire between the tread and the bead Speed Rating An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate Traction The friction between the tire and the road surface The amount of grip provided Tread The portion of a tire
93. rail airbag for the driver and the passenger seated directly behind the driver A roof rail airbag for the right front passenger and the passenger seated directly behind the right front passenger All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening Seats and Restraint System For frontal airbags the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger With seat mounted side impact airbags the word AIRBAG will appear on the side of the seatback closest to the door With roof rail airbags the word AIRBAG will appear along the headliner or trim Even if you do not have a right front passenger seat in the vehicle there is still an active frontal airbag in the right side of the instrument panel Do not place cargo in front of this airbag Z CAUTION Be sure that cargo is not near an airbag In a crash an inflating airbag might force that object toward a person This could cause severe injury or even death Secure objects away from the area in which an airbag would inflate For more information see Where Are the Airbags on page 1 45 and Loading the Vehicle on page 4 28 Airbags are designed to supplement the protection provided by safety belts Even though today s airbags are also designed to help reduce the risk o
94. reasonable speed Traction in a curve depends on the condition of the tires and the road surface the angle at which the curve is banked and vehicle speed While in a curve speed is the one factor that can be controlled If there is a need to reduce speed do it before entering the curve while the front wheels are straight Try to adjust the speed so you can drive through the curve Maintain a reasonable steady speed Wait to accelerate until out of the curve and then accelerate gently into the straightaway Steering in Emergencies There are times when steering can be more effective than braking For example you come over a hill and find a truck stopped in your lane or a car suddenly pulls out from nowhere or a child darts out from between parked cars and stops right in front of you These problems can be avoided by braking if you can stop in time But sometimes you cannot stop in time because there is no room That is the time for evasive action steering around the problem The vehicle can perform very well in emergencies like these First apply the brakes See Braking on page 4 5 It is better to remove as much speed as possible from a collision Then steer around the problem to the left or right depending on the space available An emergency like this requires close attention and a quick decision If holding the steering wheel at the recommended 9 and 3 o clock positions it can be
95. refill cooling system This service can be complex you should have your dealer retailer perform this service See Engine Coolant on page 5 22 for what to use Inspect hoses Clean radiator condenser pressure cap and filler neck Pressure test the cooling system and pressure cap j A fluid loss in any vehicle system could indicate a problem Have the system inspected and repaired and the fluid level checked Add fluid if needed k Or every 12 months whichever occurs first If you drive regularly under dusty conditions the filter may require replacement more often Maintenance Schedule 6 9 l If driving regularly under dusty conditions inspect the filter at each engine oil change m Change the fluid the first time the vehicle is serviced after 100 000 miles 166 000 km and when the vehicle is serviced after each subsequent 50 000 miles 83 000 km n Visually inspect belt for fraying excessive cracks or obvious damage Replace belt if necessary 6 10 Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety dependability and emission control performance Your dealer retailer can assist with these checks and services Be sure any necessary repairs are completed at once Whenever any fluids or lubricants are added to the vehicle make sure they are the proper ones as shown in Recommended Fluids and Lubricants
96. release The Universal Home Remote should now activate the garage door To program the remaining two Universal Home Remote buttons begin with Step 2 of Programming the Universal Home Remote System Do not repeat Step 1 Features and Controls as this will erase all previous programming from the Universal Home Remote buttons Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System call 1 800 355 3515 or go to homelink com Canadian radio frequency laws require transmitter signals to time out or quit after several seconds of transmission This may not be long enough for Universal Home Remote to pick up the signal during programming Similarly some U S gate operators are manufactured to time out in the same manner If you live in Canada or you are having difficulty programming a gate operator or garage door opener by using the Programming Universal Home Remote procedures regardless of where you live replace Step 3 under Programming Universal Home Remote with the following Continue to press and hold the Universal Home Remote button while you press and release every two seconds cycle the hand held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote The Universal Home Remote indicator light will flash slowly at first and then rapidly Proceed with Step 4 under
97. restraint it may be helpful to use your knee to push down on the child restraint as you tighten the belt 6 If the child restraint has a top tether follow the child restraint manufacturer s instructions regarding the use of the top tether See Lower Anchors and Tethers for Children LATCH on page 1 31 for more information 7 Push and pull the child restraint in different directions to be sure it is Secure To remove the child restraint unbuckle the vehicle safety belt and let it return to the stowed position If the top tether is attached to a top tether anchor disconnect it Securing a Child Restraint in the Right Front Seat Position The vehicle has airbags A rear seat is a safer place to secure a forward facing child restraint See Where to Put the Restraint on page 1 30 In addition the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions See Passenger Sensing System on page 1 51 and Passenger Airbag Status Indicator on page 3 30 for more information including important safety information A label on the sun visor says Never put a rear facing child seat in the front This is because the risk to the rear facing child is so great if the airbag deploys Seats and Restraint System 1 39 Z CAUTION CAUTION Continued A child in a rear facing child restraint can be seriously injured or kil
98. see your dealer retailer or a qualified technician for service 2 4 Features and Controls Remote Keyless Entry RKE System Operation The Remote Keyless Entry RKE transmitter functions work up to 195 feet 60 m away from the vehicle There are other conditions which can affect the performance of the transmitter See Remote Keyless Entry RKE System on page 2 3 _ fe fa NG 4 Without Remote Start Shown With Remote Start Similar Q Remote Vehicle Start For vehicles with this feature this button is used to operate the remote start feature See Remote Vehicle Start on page 2 5 for additional information Lock Press to lock all the doors including the liftgate A Unlock Press once to unlock the driver door If E is pressed again within five seconds all remaining doors unlock The interior lamps come on and stay on for 20 seconds or until the ignition is turned on amp Vehicle Locator Panic Alarm Press and release to locate the vehicle The turn signal lamps flash and the horn sounds three times Press and hold 2 to activate the panic alarm The turn signal lamps flash and the horn sounds repeatedly for 30 seconds The alarm turns off when the ignition is turned to ON RUN or when 4 is pressed again The ignition must be in LOCK OFF for the panic alarm to work Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work If a
99. the condition of the brakes the weight of the vehicle and the amount of brake force applied Avoid needless heavy braking Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic This is a mistake The brakes might not have time to cool between hard stops The brakes will wear out much faster with a lot of heavy braking Keeping pace with the traffic and allowing realistic following distances eliminates a lot of unnecessary braking That means better braking and longer brake life Driving Your Vehicle 4 5 If the engine ever stops while the vehicle is being driven brake normally but do not pump the brakes If the brakes are pumped the pedal could get harder to push down If the engine stops there will still be some power brake assist but it will be used when the brake is applied Once the power assist is used up it can take longer to stop and the brake pedal will be harder to push Adding non dealer non retailer accessories can affect vehicle performance See Accessories and Modifications on page 5 3 4 6 Driving Your Vehicle Antilock Brake System ABS This vehicle has the Antilock Brake System ABS an advanced electronic braking system that helps prevent a braking skid When the engine is started and the vehicle begins to drive away ABS checks itself A momentary motor or clicking noise might be heard while this test is going on and it mig
100. the hood down and close it firmly 5 12 Service and Appearance Care Engine Compartment Overview When you open the hood on the 2 4L L4 engine you will see the following A See Engine Air Cleaner Filter on C Engine Oil Dipstick Out of View page 5 17 See Checking Engine Oil under B Electric Engine Cooling Fan Out Engine Oil on page 5 14 of View See Cooling System on D Engine Oil Fill Cap Out of View page 5 19 See When to Add Engine Oil under Engine Oil on page 5 14 G H Brake Fluid Reservoir See Brakes on page 5 28 Engine Coolant Surge Tank See Checking Coolant under Engine Coolant on page 5 22 Remote Positive Terminal See Jump Starting on page 5 31 See Underhood Fuse Block on page 5 82 See Battery on page 5 30 J Windshield Washer Fluid Reservoir See Adding Washer Fluid under Windshield Washer Fluid on page 5 27 Service and Appearance Care When you open the hood on the 3 5L V6 engine 3 6L V6 similar you will see the following i a A See Engine Air Cleaner Filter on page 5 17 B Power Steering Fluid Reservoir Out of View See Power Steering Fluid on page 5 26 e ts a i en i c ei k C Electric Engine Cooling Fan Out of View See Cooling System on page 5 19 D Engine Oil Fill Cap See When to Add Engine Oil under Engine Oil on page 5 14 5 13 E Engine Oil Dipstick
101. the way Service and Appearance Care Be careful not to spill fuel Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle Clean fuel from painted surfaces as soon as possible See Washing Your Vehicle on page 5 75 When replacing the fuel cap turn it clockwise until it clicks Make sure the cap is fully installed The diagnostic system can determine if the fuel cap has been left off or improperly installed This would allow fuel to evaporate into the atmosphere See Malfunction Indicator Lamp on page 3 35 5 9 Z CAUTION If a fire starts while you are refueling do not remove the nozzle Shut off the flow of fuel by shutting off the pump or by notifying the station attendant Leave the area immediately Notice If you need a new fuel cap be sure to get the right type Your dealer retailer can get one for you If you get the wrong type it might not fit properly This can cause the malfunction indicator lamp to light and can damage the fuel tank and emissions system See Malfunction Indicator Lamp on page 3 35 5 10 Service and Appearance Care Filling a Portable Fuel Container CAUTION Continued Z CAUTION Never fill a portable fuel container while it is in the vehicle Static electricity discharge from the container can ignite the fuel vapor You can be badly burned and the vehicle damaged if this o
102. to get the best fuel economy possible e Avoid fast starts and accelerate smoothly e Brake gradually and avoid abrupt stops e Avoid idling the engine for long periods of time e When road and weather conditions are appropriate use cruise control if equipped e Always follow posted speed limits or drive more slowly when conditions require e Keep vehicle tires properly inflated e Combine several trips into a single trip e Replace the vehicle s tires with the same TPC Spec number molded into the tire s sidewall near the size Follow recommended scheduled maintenance Defensive Driving Defensive driving means always expect the unexpected The first step in driving defensively is to wear your safety belt See Safety Belts They Are for Everyone on page 1 10 Driving Your Vehicle 4 3 Z CAUTION Assume that other road users pedestrians bicyclists and other drivers are going to be careless and make mistakes Anticipate what they might do and be ready In addition e Allow enough following distance between you and the driver in front of you e Focus on the task of driving Driver distraction can cause collisions resulting in injury or possible death These simple defensive driving techniques could save your life 4 4 Driving Your Vehicle Drunk Driving Z CAUTION Drinking and then driving is very dangerous Your reflexes perceptions atte
103. to inflate if the impact exceeds a predetermined deployment threshold Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants Whether the frontal airbags will or should deploy is not based on how fast your vehicle is traveling It depends largely on what you hit the direction of the impact and how quickly your vehicle slows down Seats and Restraint System Frontal airbags may inflate at different crash speeds For example e If the vehicle hits a stationary object the airbags could inflate at a different crash speed than if the vehicle hits a moving object e If the vehicle hits an object that deforms the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform e If the vehicle hits a narrow object like a pole the airbags could inflate at a different crash speed than if the vehicle hits a wide object like a wall e Ifthe vehicle goes into an object at an angle the airbags could inflate at a different crash speed than if the vehicle goes straight into the object 1 47 Thresholds can also vary with specific vehicle design Frontal airbags are not intended to inflate during vehicle rollovers rear impacts or in many side impacts In addition the vehicle has dual stage frontal airbags Dual stage airbags adjust the restraint according to crash severity Th
104. transmitter is lost or stolen a replacement can be purchased and programmed through your dealer retailer When the replacement transmitter is programmed to the vehicle all remaining transmitters must also be programmed Any lost or stolen transmitters no longer work once the new transmitter is programmed Each vehicle can have up to eight transmitters programmed to it See Relearn Remote Key under DIC Operation and Displays on page 3 42 Battery Replacement Replace the battery if the REPLACE REMOTE KEY FOB BATTERY message displays on the Driver Information Center DIC See REPLACE REMOTE KEY FOB BATTERY under DIC Warnings and Messages on page 3 49 Notice When replacing the battery do not touch any of the circuitry on the transmitter Static from your body could damage the transmitter To replace the battery 1 Separate the transmitter with a flat thin object inserted into the notch on the side 2 Remove the old battery Do not use a metal object 3 Insert the new battery positive side facing down Replace with a CR2032 or equivalent battery 4 Reassemble the transmitter Features and Controls 2 5 Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle It may also start the vehicle s heating or air conditioning systems and rear window defogger Normal operation of the climate control system returns after
105. turned a full 180 degrees very quickly without removing either hand But you have to act fast steer quickly and just as quickly straighten the wheel once you have avoided the object The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly Off Road Recovery The vehicle s right wheels can drop off the edge of a road onto the shoulder while driving If the level of the shoulder is only slightly below the pavement recovery should be fairly easy Ease off the accelerator and then if there is nothing in the way steer so that the vehicle straddles the edge of the pavement Turn the steering wheel 3 to 5 inches 8 to 13 cm about one eighth turn until the right front tire contacts the pavement edge Then turn the steering wheel to go straight down the roadway Driving Your Vehicle 4 11 Passing Passing another vehicle on a two lane road can be dangerous To reduce the risk of danger while passing Look down the road to the sides and to crossroads for situations that might affect a successful pass If in doubt wait e Watch for traffic signs pavement markings and lines that could indicate a turn or an intersection Never cross a solid or double solid line on your side of the lane e Do not get too close to the vehicle you want to pass Doing so can reduce your visibility e Wait your turn to pass a slo
106. use the delete command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Delete The system responds with Delete please say the name tag followed by a tone 3 Say the name tag to be deleted The system responds with Would you like to delete lt name tag gt Please say yes or no e Ifthe name tag is correct say Yes to delete the name tag The system responds with OK deleting lt name tag gt returning to the main menu e Ifthe name tag is incorrect say No The system responds with No OK let s try again please say the name tag 3 86 Instrument Panel Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar if present To use the delete all name tags command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Delete all name tags The system responds with You are about to delete all name tags stored in your phone directory and your route destination directory Are you sure you want to do this Please say yes or no e Say Yes to delete all name tags e Say No to cancel the function and return to the main menu Making a Call Calls can be made using the following commands e Dial e Digit Dial e Call e Re dial Using t
107. vehicle seats by lap belts or the lap belt portion of a lap shoulder belt or by the LATCH system See Lower Anchors and Tethers for Children LATCH on page 1 31 for more information A child can be endangered in a crash if the child restraint is not properly secured in the vehicle Seats and Restraint System When securing an add on child restraint refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet or both and to this manual The child restraint instructions are important so if they are not available obtain a replacement copy from the manufacturer Keep in mind that an unsecured child restraint can move around ina collision or sudden stop and injure people in the vehicle Be sure to properly secure any child restraint in the vehicle even when no child is in it Securing the Child Within the Child Restraint Z CAUTION A child can be seriously injured or killed in a crash if the child is not properly secured in the child restraint Secure the child properly following the instructions that came with that child restraint Where to Put the Restraint According to accident statistics children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position We recommend that children and child restraints be secured in a rear seat including an infant or a chil
108. vehicle by pushing or pulling it will not work and it could damage the vehicle 1 Check the other vehicle It must have a 12 volt battery with a negative ground system Notice lf the other vehicle s system is not a 12 volt system with a negative ground both vehicles can be damaged Only use vehicles with 12 volt systems with negative grounds to jump start your vehicle 2 Get the vehicles close enough so the jumper cables can reach but be sure the vehicles are not touching each other If they are it could cause a ground connection you do not want You would not be able to start your vehicle and the bad grounding could damage the electrical systems 5 31 To avoid the possibility of the vehicles rolling set the parking brake firmly on both vehicles involved in the jump start procedure Put the transmission in P Park before setting the parking brake Notice f you leave the radio or other accessories on during the jump starting procedure they could be damaged The repairs would not be covered by the warranty Always turn off the radio and other accessories when jump starting the vehicle 3 Turn off the ignition on both vehicles Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlet Turn off the radio and all lamps that are not needed This will avoid sparks helping save both batteries and the radio 5 32 4 Open the hood on the other vehicle and loca
109. while the engine is running at high speed is dangerous Unless your foot is firmly on the brake pedal the vehicle could move very rapidly You could lose control and hit people or objects Do not shift into a drive gear while the engine is running at high speed Notice Shifting out of P Park or N Neutral with the engine running at high speed may damage the transmission The repairs would not be covered by the vehicle warranty Be sure the engine is not running at high speed when shifting the vehicle D Drive This position is for normal driving with the automatic transmission It provides the best fuel economy If you need more power for passing and you are e Going less than about 35 mph 55 km h push the accelerator pedal about halfway down Going about 35 mph 55 km h push the accelerator all the way down Downshifting the transmission in slippery road conditions could result in skidding see Skidding under Loss of Control on page 4 12 Notice Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission The repair will not be covered by the vehicle warranty If you are stuck do not spin the tires When stopping on a hill use the brakes to hold the vehicle in place Manual Shift Mode MSM Automatic Transmission To use this feature do the following 1 Move the shift lever from D Drive to the left into
110. would move too far forward which would increase the chance of head and neck injury Also the belt would apply too much force to the ribs which are not as strong as shoulder bones You could also severely injure internal organs like your liver or spleen The shoulder belt should go over the shoulder and across the chest 1 18 Seats and Restraint System Q What is wrong with this A The belt is behind the body Z CAUTION You can be seriously injured by not wearing the lap shoulder belt properly In a crash you would not be restrained by the shoulder belt Your body could move too far forward increasing the chance of head and neck injury You might also slide under the lap belt The belt force would then be applied right on the abdomen That could cause serious or fatal injuries The shoulder belt should go over the shoulder and across the chest Q What is wrong with this A The belt is twisted across the body Z CAUTION You can be seriously injured by a twisted belt In a crash you would not have the full width of the belt to spread impact forces If a belt is twisted make it straight so it can work properly or ask your dealer retailer to fix it Lap Shoulder Belt All seating positions in the vehicle have a lap shoulder belt The following instructions explain how to wear a lap shoulder belt properly 1 Adjust the seat if the seat is adjus
111. 0 in LOT mm v7 7 0 044 in Li mm 5 88 Service and Appearance Care 4 NOTES Maintenance Schedule 6 1 Maintenance Schedule Maintenance Schedule Introduction 2 2eceeeeeeeeeeees 6 1 Maintenance Requirements 6 1 Your Vehicle and the Environment 0 se0seeeseeeeees 6 1 Using the Maintenance Schedule ccccceeseseeeeseeeees 6 2 Scheduled Maintenance 6 3 Additional Required Services 6 6 Maintenance Footnotes 6 8 Owner Checks and Services ccecseesseeseeeseeeeees 6 10 At Each Fuel Fill 06 6 10 At Least Once a Month 6 10 At Least Once a Year 6 11 Recommended Fluids and Lubricants s0se0 6 13 Maintenance Replacement PANTS erences aringa enasna 6 15 Engine Drive Belt Routing 6 16 Maintenance Record 6 17 Maintenance Schedule Introduction Important Keep engine oil at the proper level and change as recommended Maintenance Requirements Notice Maintenance intervals checks inspections replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep this vehicle in good working condition Any damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep the vehicle in good working condition but also helps the en
112. 2 11 Theft Deterrent Systems Theft Deterrent Systems 2 12 Content Theft Deterrent 2 12 PASS Key Ill Electronic Immobilizer 2s0seeeeeee eee 2 13 PASS Key Ill Electronic Immobilizer Operation 2 14 Starting and Operating Your Vehicle New Vehicle Break In 2 15 Ignition Positions seee 2 16 Retained Accessory Power RAP cseeee 2 17 Starting the Engine 2 17 Engine Coolant Heater 2 18 Automatic Transmission Operation Uplevel 2 19 Automatic Transmission Operation Base eee 2 22 Parking Brake cssceeeeeeees 2 24 Shifting Into Park Automatic Transmission e e 2 Shifting Out of Park 2 27 Parking Over Things That Burn ececeeeeeeeeeenes 2 27 Engine Exhaust eee 2 28 Running the Vehicle While Parked 0seeeeeee 2 28 Features and Controls 2 1 Mirrors Manual Rearview Mirror 2 29 Automatic Dimming Rearview Mirror s sseeeee 2 29 Outside Power Mirrors 2 29 Outside Convex Mirror 2 30 Outside Heated Mirrors 2 30 Object Detection Systems Rear Vision Camera RVC seese 2 31 OnStar System OnStar System ccccceeeeeeee 2 33 Universal Home Remote System Universal Home Remote System esececeeeseesseeeeserseeees 2 37 Universal Home Remote System Operation 2 37 Storage Areas Glove BOX ccessceseeeeeeaeeeeees 2
113. 2 22 Transportation Courtesy 7 9 Trip Odometer 3 28 Turn and Lane Change Signals isk szaseedes ie ep aai 3 6 Turn Signal Multifunction OVOP secticnadtodesadamemeeean ai 3 6 INDEX U Uniform Tire Quality Grading Universal Home Remote System Operation Vehicle Control Design Loading Running While Parked Service Soon Light Symbols Vehicle Customization DIC Vehicle Data Recording and PRIVACY cismini cada siaina Vehicle Data Recording Radio Frequency RFID Vehicle Identification Number VIN cases Service Parts Identification Label Vehicle Remote Start Ventilation Adjustment MISOFS aeara aee a Gotan AE i 11 i 12 INDEX W Warning Lights Gages and Indicators Warnings DIC Warnings and Messages Hazard Warning Flashers Safety and Symbols Washer Fluid Low Warning Light Wheels Alignment and Tire Balance Different Size Replacement When It Is Time for New Tires Where to Put the Child Restraint Windows Power Windshield Rainsense Wipers Washer Washer Fluid Windshield cont Wiper Blade Replacement 5 42 Wiper Blades Cleaning 5 76 Wiper Fuses 265 5 80 WIDONS ranatiers naoa 3 7 Winter Driving 4 25 Wiper Activated Headlamps 3 12 Wipers Rear Washer uiis 3 9 X XM Radio Messages 3 79 XM Sat
114. 2009 Saturn VUE Owner Manual LH Seats and Restraint System 00 0 1 1 Head Restraints 1 2 Front Seats ow eee 1 3 Rear SeatS ow 1 9 Safety Belts oo 1 10 Child Restraints oo 1 23 Airbag System _ 1 42 Restraint System CHECKS Coenin Ae 1 58 Features and Controls 2 1 Keys oiera ioten 2 2 Doors and Locks _ 2 7 Windows nsasssssissrreereesrns 2 10 Theft Deterrent Systems oo eee 2 12 Starting and Operating Your Vehicle _ 2 15 Mitros avosssiecacneandsaceeacass 2 29 Object Detection Systems oo 2 31 OnStar System uu 2 33 Universal Home Remote System Storage Areas Sunroof Instrument Panel Instrument Panel Overview Climate Controls Warning Lights Gages and Indicators Driver Information Center DIC Audio System s Driving Your Vehicle Your Driving the Road and the Vehicle Towing Service and appearance Care ecese ervice Fuel Checking Things Under the Hood All Wheel Drive _ 5 35 Headlamp Aiming _ 5 36 Bulb Replacement _ 5 39 Windshield Wiper Blade Replacement _ 5 42 TGS sesigesetetesechsideseieets 5 43 Appearance Care _ 5 72 Vehicle Identification 5 79 Electrical System _ 5 79 Capacities and Specifications 5 86 Maintenance Schedule 6 1 Maintenance Schedule _ 6 1 Customer Assistance Informati
115. 3 files on the CD R or CD RW can be listened to in random rather than sequential order on one CD R CD RW or all discs in a six disc CD player To use random do one of the following 1 To play MP3 files from the CD R or CD RW in random order press the pushbutton positioned under the RDM label until Random Current Disc displays Press the same pushbutton again to turn off random play 2 To play songs from all CDs loaded in a six disc CD player in random order press the pushbutton positioned under the RDM label until Randomize All Discs displays Press the same pushbutton again to turn off random play Music Navigator Use the music navigator feature to play MP3 files on the CD R or CD RW in order by artist or aloum Press the pushbutton located below the music navigator label The player scans the disc to sort the files by artist and album ID3 tag information It can take several minutes to scan the disc depending on the number of MP3 files recorded to the CD R or CD RW The radio can begin playing while it is scanning the disc in the background When the scan is finished the CD R or CD RW begins playing again Once the disc has been scanned the player defaults to playing MP3 files in order by artist The current artist playing is shown on the second line of the display between the arrows Once all songs by that artist are played the player moves to the next artist in alphabetical order on the CD R CD RW a
116. 4 Manual Lumbar eee0ee 1 5 Heated Seats eseseeeeeeees 1 5 Reclining Seatbacks 5 1 6 Passenger Folding Seatback 1 8 Rear Seats Split Folding Rear Seat 1 9 Safety Belts Safety Belts They Are for Everyone eeceeeeeeeeee 1 10 How to Wear Safety Belts Properly 00 1 14 Lap Shoulder Belt 6 1 19 Safety Belt Use During PrOQNaNCy 2ceeeeeee eee 1 23 Safety Belt Extender 1 23 Seats and Restraint System Child Restraints Older Children 2 s 0000 1 23 Infants and Young Children 1 26 Child Restraint Systems 1 29 Where to Put the Restraint 1 30 Lower Anchors and Tethers for Children LATCH 1 31 Securing a Child Restraint in a Rear Seat Position 1 37 Securing a Child Restraint in the Right Front Seat POSItION cececeeeeeeeeeeeeees 1 39 Airbag System Airbag System csseeeeeeeees 1 42 Where Are the Airbags 1 45 When Should an Airbag Inflate 2ccecceceeeeeeeseeeeneees 1 47 What Makes an Airbag Inflate ccecececeeeeeeeeeeeeees 1 49 How Does an Airbag Restrain c scsescsecenes 1 49 What Will You See After an Airbag Inflates 1 50 Passenger Sensing System 1 51 Servicing Your Airbag Equipped Vehicle 1 56 Adding Equipment to Your Airbag Equipped Vehicle 1 57 Restraint System Check Checking the Rest
117. 4 35 Driving Your Vehicle 4 1 Your Driving the Road and the Vehicle Driving Your Vehicle Whenever we drive we are taking on an important responsibility This is true for any motor vehicle passenger Car van truck sport utility Driver behavior the driving environment and the vehicle s design all affect how well a vehicle performs But statistics show that the most important factor by far is how we drive Knowing how these three factors work together can help you understand how your vehicle handles and what you can do to avoid many types of crashes including a rollover crash 4 2 Driving Your Vehicle Driver Behavior The single most important thing is this everyone in the vehicle including the driver should buckle up See Safety Belts They Are for Everyone on page 1 10 In fact most serious injuries and fatalities to unbelted occupants can be reduced or prevented by the use of safety belts In a rollover crash an unbelted person is significantly more likely to die than a person wearing a seat belt In addition avoiding excessive speed sudden or abrupt turns and drunken or aggressive driving can help make trips safer and avoid the possibility of a crash especially a rollover crash This section provides many useful tips to help you drive more safely Driving Environment You can also help avoid a rollover or other type of crash by being prepared for driving in inclement weather a
118. ANSMITTERS TO YOUR VEHICLE under Remote Keyless Entry RKE System Operation on page 2 4 and DIC Operation and Displays on page 3 42 for more information 3 54 Instrument Panel REPLACE REMOTE KEY FOB BATTERY This message displays if a Remote Keyless Entry RKE transmitter battery is low The battery needs to be replaced in the transmitter See Battery Replacement under Remote Keyless Entry RKE System Operation on page 2 4 SERVICE A C Air Conditioning SYSTEM This message displays when there is a problem detected in the air conditioning system Have the vehicle serviced by your dealer retailer SERVICE AIR BAG This message displays when there is a problem with the airbag system Have your vehicle serviced by your dealer retailer immediately See Airbag Readiness Light on page 3 29 for more information SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system or when the brake fluid level is low See Brake System Warning Light on page 3 31 Have the brake system serviced by your dealer retailer as soon as possible SERVICE POWER STEERING If the vehicle has electric power steering this message displays if a problem has been detected with the power steering See Steering on page 4 9 for more information SERVICE STABILITRAK This message displays if there has been a problem detected with StabiliTrak A warning l
119. DR is to record in certain crash or near crash like situations such as an airbag deployment or hitting a road obstacle data that will assist in understanding how a vehicle s systems performed The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time typically 30 seconds or less The EDR in this vehicle is designed to record such data as How various systems in your vehicle were operating e Whether or not the driver and passenger safety belts were buckled fastened e How far if at all the driver was pressing the accelerator and or brake pedal e How fast the vehicle was traveling This data can help provide a better understanding of the circumstances in which crashes and injuries occur Important EDR data is recorded by your vehicle only if a non trivial crash situation occurs no data is recorded by the EDR under normal driving conditions and no personal data e g name gender age and crash location is recorded However other parties such as law enforcement could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation To read data recorded by an EDR special equipment is required and access to the vehicle or the EDR is needed In addition to the vehicle manufacturer other parties such as law enforcement that have the special equipment can read the information if they have access
120. KE System Operation on page 2 4 for more information Press the customization button until PRESS V TO SET REMOTE DOOR UNLOCK appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings VERIF LIGHTS OFF The exterior lamps will not flash when you press the unlock button on the RKE transmitter VERIF LIGHTS ON default The exterior lamps will flash when you press the unlock button on the RKE transmitter VERIF NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle s doors will be delayed When locking the doors with the power door lock switch and a door is open this feature will delay locking the doors until five seconds after the last door is closed You will hear three chimes to signal that the delayed locking feature is in use The key must be out of the ignition for this feature to work You can temporarily override delayed locking by pressing the power door lock switch twice or the lock button on the RKE transmitter twice See Delayed Locking on page 2 8 for more information Press the customization button until PRESS TO SET DELAY DOOR LOCK appears on the DIC di
121. N Things that can burn could touch hot exhaust parts under the vehicle and ignite Do not park over papers leaves dry grass or other things that can burn 2 28 Engine Exhaust Features and Controls Z CAUTION CAUTION Continued Engine exhaust contains Carbon Monoxide CO which cannot be seen or smelled Exposure to CO can cause unconsciousness and even death Exhaust may enter the vehicle if e The vehicle idles in areas with poor ventilation parking garages tunnels deep snow that may block underbody airflow or tail pipes e The exhaust smells or sounds strange or different e The exhaust system leaks due to corrosion or damage Continued e The vehicle s exhaust system has been modified damaged or improperly repaired e There are holes or openings in the vehicle body from damage or after market modifications that are not completely sealed If unusual fumes are detected or if it is Suspected that exhaust is coming into the vehicle e Drive it only with the windows completely down e Have the vehicle repaired immediately Never park the vehicle with the engine running in an enclosed area such as a garage ora building that has no fresh air ventilation Running the Vehicle While Parked It is better not to park with the engine running But if you ever have to here are some things to know Z CAUTION Idling a vehicle in an enclosed are
122. N MM DD YYYY displays 4 Press the softkey below any one of the tabs you want to change 5 To increase the time or date do one of the following e Press the softkey located below the selected tab Press gt I SEEK or DD FWD e Turn J clockwise 6 To decrease the time or date do one of the following e Press KI SEEK or lt REV e Turn J counterclockwise The date does not automatically display To see the date press MENU and then softkey below the tab while the radio is on The date with display times out after a few seconds and goes back to the normal radio and time display To change the time default setting from 12 hour to 24 hour or to change the date default setting from month day year to day month year 1 Press MENU and then the softkey below the tab The HR MIN MM DD YYYY displays 2 Press the softkey below the forward arrow tab The time 12H and 24H and the date MM DD YYYY month day and year and DD MM YYYY day month and year displays 3 Press the softkey located below the desired option 4 Press MENU again to apply the selected default or let the screen time out Radio s ca T E gl S emet Radio with CD shown Radio with Six Disc CD similar Radio Data System RDS The audio system has a Radio Data System RDS The RDS feature is available for use only on FM stations that broadcast RDS information This system relies upon
123. ON RUN and apply the regular brake pedal Notice Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key Use the correct key make sure it is all the way in and turn it only with your hand If the key cannot be turned by hand see your dealer retailer Features and Controls LOCK OFF This position locks the ignition It also locks the steering wheel and the transmission The key can only be removed in LOCK OFF The shift lever must be in P Park to turn the ignition switch to LOCK OFF The steering can bind with the wheels turned off center If this happens move the steering wheel from right to left while turning the key to ACC ACCESSORY If this doesn t work the vehicle needs service ACC ACC ACCESSORY This is the position in which you can operate the electrical accessories or items plugged into the accessory power outlets Use this position if the vehicle must be pushed or towed ON RUN This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights The switch stays in this position when the engine is running The transmission is also unlocked in this position If you leave the key in the ACC ACCESSORY or ON RUN positions with the engine off the battery could be drained You may not be able to start the vehicle if the battery is allowed to drain for an extended period of time
124. RVC system always check carefully before backing up by checking behind and around the vehicle The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle 2 31 When the key is in the ON RUN position and the driver shifts the vehicle into R Reverse the video image automatically appears on the inside rear view mirror Once the driver shifts out of R Reverse the video image automatically disappears from the inside rear view mirror Turning the Rear Vision Camera System Off or On To turn off the rear vision camera system press and hold located on the inside rearview mirror until the left indicator light turns off The rear vision camera display is now disabled To turn the rear vision camera system on again press and hold until the left indicator light illuminates The rear vision camera system display is now enabled and the display will appear in the mirror normally 2 32 Rear Vision Camera Location The camera is located in the rear of the vehicle The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper The area displayed can vary depending on vehicle orientation or road conditions The distance of the image that appears on the screen differs from the actual distance The following illustration shows the field of view that the c
125. See Reclining Seatbacks on page 1 6 Seats and Restraint System 1 9 Rear Seats Split Folding Rear Seat The rear split bench seatbacks can be folded forward upright or partially reclined independent of the other seatback position Z CAUTION If either seatback is not locked it could move forward in a sudden stop or crash That could cause injury to the person sitting there Always push and pull on the seatbacks to be sure they are locked Z CAUTION A safety belt that is improperly routed not properly attached or twisted will not provide the protection needed in a crash The person wearing the belt could be seriously injured After raising the rear seatback always check to be sure that the safety belts are properly routed and attached and are not twisted To fold the seatback down Notice Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat 1 Unbuckle all three safety belts and put the front seatback in an upright position 1 10 2 Lift the lever located on the top of the seatback to release the seatback and fold the seatback forward To recline the seatback 1 Lift and hold the lever located on top of the seatback 2 Tilt the seatback rearward then release the lever Seats and Restraint
126. Service and Appearance Care See the Tire Size illustration later in this section for more detail B TPC Spec Tire Performance Criteria Specification Original equipment tires designed to GM s specific tire performance criteria have a TPC specification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines C DOT Department of Transportation The Department of Transportation DOT code indicates that the tire is in compliance with the U S Department of Transportation Motor Vehicle Safety Standards D Tire Identification Number TIN The letters and numbers following DOT Department of Transportation code is the Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of the tire although only one side may have the date of manufacture E Tire Ply Material The type of cord and number of plies in the sidewall and under the tread F Uniform Tire Quality Grading UTQG Tire manufacturers are required to grade tires based on three performance factors treadwear traction and temperature resistance For more information see Uniform Tire Quality Grading on page 5 60 G Maximum Cold Inflation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load Compact Spare Tire Example A Tem
127. System 1 7 Power Reclining Seatbacks Z CAUTION iy Sitting in a reclined position when ma your vehicle is in motion can be dangerous Even if you buckle up J your safety belts cannot do their P job when you are reclined like this A F The shoulder belt cannot do its job In a crash you could go into it receiving neck or other injuries The lap belt cannot do its job either In a crash the belt could go Do not have a seatback reclined if up over your abdomen The belt the vehicle is moving forces would be there not at your pelvic bones This could cause serious internal injuries Ye j st ree Yo If the seats have power reclining seatbacks the control used to recline them is located on the outboard side of the seat e To recline the seatback tilt the top of the control rearward For proper protection when the vehicle is in motion have the s seatback upright Then sit well To bring the seatback forward tilt back in the seat and wear your the top of the control forward safety belt properly 1 8 Seats and Restraint System Passenger Folding Seatback The front passenger seatback may fold flat Z CAUTION Z CAUTION If you fold the seatback forward to carry longer objects such as skis be sure any such cargo is not near an airbag In a crash an inflating airbag might force that object toward a person This could cause severe injury or even death
128. TION Changing a tire can be dangerous The vehicle can slip off the jack and roll over or fall on you or other people You and they could be badly injured or even killed Find a level place to change your tire To help prevent the vehicle from moving 1 Set the parking brake firmly 2 Put an automatic transmission shift lever in P Park or shift a manual transmission to 1 First or R Reverse Continued 3 Turn off the engine and do not restart while the vehicle is raised 4 Do not allow passengers to remain in the vehicle To be certain the vehicle will not move put blocks at the front and rear of the tire farthest away from the one being changed That would be the tire on the other side at the opposite end of the vehicle When the vehicle has a flat tire B use the following example as a guide to assist you in the placement of wheel blocks A A Wheel Block B Flat Tire The following information explains how to use the jack and change a tire Removing the Spare Tire and Tools To access the spare tire 1 Open the liftgate 2 Push the levers on the load floor Service and Appearance Care 3 Lift the load floor and hang the hook to the tailgate opening 4 Remove the tire protector foam 5 65 e 5 Remove the wheel retainer bolt holding down the spare tire by turning it counterclockwise 6 Remove the compact spare tire See C
129. The vehicle has components and labels that use symbols instead of text Symbols are shown along with the text describing the operation or information relating to a specific component control message gage or indicator CA This symbol is shown when you need to see your owner manual for additional instructions or information This symbol is shown when you need to see a service manual for additional instructions or information iv Preface Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean For more information on the symbol refer to the index Airbag Readiness Light X Air Conditioning Antilock Brake System ABS Audio Steering Wheel Controls or OnStar Brake System Warning Light Charging System 1 Cruise Control E Engine Coolant Temperature Exterior Lamps 40 Fog Lamps D Fuel Gage 41 Fuses Headlamp High Low Beam Changer LATCH System Child Restraints Malfunction Indicator Lamp 7i Oil Pressure J D C E gt p Power Remote Vehicle Start Safety Belt Reminders Tire Pressure Monitor Traction Control Windshield Washer Fluid Seats and Restraint System Head Restraints Head Restraints 1 2 Front Seats Manual Seats e eseeeeeee 1 3 Seat Height Adjuster 1 4 Power Seat sceceeeseeeeeeeeees 1
130. WR or either the maximum front or rear Gross Axle Weight Rating GAWR If you do parts on the vehicle can break and it can change the way your Continued CAUTION Continued vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of the vehicle Tire and Loading Information Label 3 m a i i kriba ue a Cc E Example Label A vehicle specific Tire and Loading Information label is attached to the center pillar B pillar of your vehicle With the drivers door open you will find the label attached below the door lock post striker The tire and loading information label shows the number of occupant seating positions A and the maximum vehicle capacity weight B in kilograms and pounds The Tire and Loading Information label also shows the size of the original equipment tires C and the recommended cold tire inflation pressures D For more information on tires and inflation see Tires on page 5 43 and Inflation Tire Pressure on page 5 49 There is also important loading information on the vehicle Certification Tire label It tells you the Gross Vehicle Weight Rating GVWR and the Gross Axle Weight Rating GAWR for the front and rear axle See Certification Tire Label later in this section Steps for Determining Correct Load Limit 1 Locate the statement The co
131. a more thorough cleaning is necessary a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt Never use spot lifters or removers on plastic surfaces Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of the interior and are not recommended Do not use silicone or wax based products or those containing organic solvents to clean the vehicle s interior because they can alter the appearance by increasing the gloss in a non uniform manner Some commercial products may increase gloss on the instrument panel The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions Care of Safety Belts Keep belts clean and dry Z CAUTION Do not bleach or dye safety belts It may severely weaken them In a crash they might not be able to provide adequate protection Clean safety belts only with mild soap and lukewarm water Weatherstrips Silicone grease on weatherstrips will make them last longer seal better and not stick or squeak Apply silicone grease with a clean cloth During very cold damp weather frequent application may be required See Recommended Fluids and Lubricants on page 6 13 Washing Your Vehicle The best way to preserve the vehicle s finish is to keep it
132. a with poor ventilation is dangerous Engine exhaust may enter the vehicle Engine exhaust contains Carbon Monoxide CO which cannot be seen or smelled It can cause unconsciousness and even death Never run the engine in an enclosed area that has no fresh air ventilation For more information see Engine Exhaust on page 2 28 Z CAUTION It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P Park with the parking brake firmly set The vehicle can roll Do not leave the vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure the vehicle will not move even when you are on fairly level ground always set the parking brake and move the shift lever to P Park Follow the proper steps to be sure the vehicle will not move See Shifting Into Park Automatic Transmission on page 2 25 If parking on a hill and pulling a trailer see Towing a Trailer on page 4 35 Mirrors Manual Rearview Mirror If the vehicle has the manual rearview mirror it can be adjusted by holding the mirror in the center to move it for a clearer view behind your vehicle Reduce the glare of headlamps from behind by pushing the lever forward or pulling it back for daytime nighttime use Automatic Dimming Rearview Mirror The vehicle may have an a
133. acement of the original tires with other than those of the same Tire Performance Criteria TPC can affect the vehicle s emission controls and can cause this light to come on Modifications to these systems could lead to costly repairs not covered by the vehicle warranty This could also result in a failure to pass a required Emission Inspection Maintenance test See Accessories and Modifications on page 5 3 This light comes on during a malfunction in one of two ways Light Flashing A misfire condition has been detected A misfire increases vehicle emissions and could damage the emission control system on the vehicle Diagnosis and service might be required 3 36 Instrument Panel The following can prevent more serious damage to the vehicle e Reduce vehicle speed e Avoid hard accelerations e Avoid steep uphill grades e If towing a trailer reduce the amount of cargo being hauled as soon as it is possible If the light continues to flash when it is safe to do so stop the vehicle Find a safe place to park the vehicle Turn the key off wait at least 10 seconds and restart the engine If the light is still flashing follow the previous steps and see your dealer retailer for service as soon as possible Light On Steady An emission control system malfunction has been detected on the vehicle Diagnosis and service might be required An emission system malfunction might be corrected by checking the foll
134. ada section within www gm ca Customer Assistance for Text Telephone TTY Users To assist owners who have hearing difficulties Saturn has installed special TDD Telecommunication Devices for the Deaf equipment in its Saturn Customer Assistance Center Any hearing or speech impaired customer who has access to a TDD or to a conventional Text Telephone TTY can communicate with Saturn by dialing 1 800 TDD 6000 TTY users in Canada may dial 1 800 263 3830 Customer Assistance Information 7 5 Customer Assistance Offices Saturn encourages customers to call the toll free number for assistance If a customer wishes to write to Saturn the letter should be addressed to Saturn Customer Assistance Center P O Box 33173 Detroit MI 48232 5173 1 800 553 6000 1 800 833 6000 For Text Telephone devices TTYs Roadside Assistance 1 800 553 6000 In Canada write to Saturn Customer Communication Centre General Motors of Canada Ltd CA1 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 GMcanada com 1 800 263 1999 1 800 263 3830 For Text Telephone devices TTYs Roadside Assistance 1 800 268 6800 7 6 Customer Assistance Information GM Mobility Reimbursement Program FE MOBILITY This program available to qualified applicants can reimburse you up to 1 000 toward eligible aftermarket driver or passenger adaptive equipment you may require for your vehicle such as hand controls wheelchai
135. aded onto the top of the vehicle Crossrails may be purchased at your dealer retailer Notice Loading cargo on the luggage carrier that weighs more than 200 Ibs 91 kg or hangs over the rear or sides of the vehicle can damage the vehicle Load cargo so that it rests as far forward as possible and against the side rails making sure to fasten it securely Do not exceed the maximum vehicle capacity when loading your vehicle For more information on vehicle capacity and loading see Loading the Vehicle on page 4 28 Check that all cargo is securely fastened to prevent damage or loss while driving 2 44 Rear Seat Armrest A Eom En To access the rear seat armrest pull the handle down Lift the top of the armrest to access the storage area Convenience Net Use the convenience net located in the rear to store small loads as far forward as possible The net should not be used to store heavy loads Features and Controls Cargo Cover For vehicles with a cargo cover use it to cover items in the rear of the vehicle To remove the cover and remove it from the vehicle pull both ends toward each other To reinstall place each end of the cover in the holes behind the rear seat Cargo Tie Downs Four cargo tie downs are located in the rear compartment of the vehicle The tie downs can be used to secure small loads Cargo Management System If the vehicle has a cargo management system in the rear o
136. ades if contaminated Replace wiper blades that are worn or damaged See Windshield Wiper Blade Replacement on page 5 42 and Windshield and Wiper Blades on page 5 76 for more information e Make sure the safety belt reminder light and safety belt assemblies are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a Safety belt system from doing its job have it repaired Have any torn or frayed safety belts replaced Also see Checking the Restraint Systems on page 1 58 f Lubricate all key lock cylinders door hinges and latches hood hinges and latches glove box hinges sunroof if equipped and any folding seat hardware More frequent lubrication may be required when exposed to a corrosive environment Applying silicone grease on weatherstrips with a clean cloth will make them last longer seal better and not stick or squeak g Check system for interference or binding and for damaged or missing parts Replace parts as needed Replace any components that have high effort or excessive wear h Severe service is when the vehicle is mainly driven under one or more of these conditions In heavy city traffic where the outside temperature regularly reaches 90 F 32 or higher In hilly or mountainous terrain When doing frequent trailer towing Uses such as found in taxi police or delivery service i Drain flush and
137. adly that they will have to be replaced Do not let someone put in the wrong kind of fluid If brake fluid is spilled on the vehicle s painted surfaces the paint finish can be damaged Be careful not to spill brake fluid on the vehicle If you do wash it off immediately See Washing Your Vehicle on page 5 75 Service and Appearance Care Brake Wear This vehicle has disc brakes Disc brake pads have built in wear indicators that make a high pitched warning sound when the brake pads are worn and new pads are needed The sound can come and go or be heard all the time the vehicle is moving except when applying the brake pedal firmly Z CAUTION The brake wear warning sound means that soon the brakes will not work well That could lead to an accident When the brake wear warning sound is heard have the vehicle serviced Notice Continuing to drive with worn out brake pads could result in costly brake repair 5 29 Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied This does not mean something is wrong with the brakes Properly torqued wheel nuts are necessary to help prevent brake pulsation When tires are rotated inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 5 86 Brake linings should always be replaced as complete axle set
138. aintenance II may be required more often 6 4 Maintenance Schedule Maintenance I Use Maintenance II Use Maintenance II whenever the light Maintenance I if the Change Engine Maintenance II if the previous displays 10 months or more since Oil light displays within 10 months service performed was the last service or if the light has not since the vehicle was purchased or Maintenance I Always use come on at all for one year Maintenance II was performed Scheduled Maintenance Change engine oil and filter See Engine Oil on page 5 14 Reset oil life system See Engine Oil Life System on page 5 16 An Emission Control Service Visually check for any leaks or damage See footnote j ooo e o e Inspect engine air cleaner filter If necessary replace filter See Engine Air Cleaner Filter on page 5 17 See footnote l Rotate tires and check inflation pressures and wear See Tire Inspection and Rotation on page 5 56 and Tire Wear Inspection in At Least Once a Month on page 6 10 Inspect brake system See footnote a ooo e o e e Check engine coolant and windshield washer fluid levels and add fluid as needed Maintenance Schedule 6 5 Scheduled Maintenance coni d Perform any needed additional services See Additional Required Services in this section Inspect suspension and steering components See footnote b a i Inspect engine cooling system See footnote c a i Inspect wiper blades See foo
139. air conditioning compressor unless the outside air is at or below freezing Recirculation mode cannot be selected while in defog mode This helps prevent window fogging W Defrost This mode removes fog or frost from the windshield more quickly Air is directed to the windshield and the side window outlets In this mode the system turns the recirculation mode off automatically and runs the air conditioning compressor unless the outside air is at or below freezing Recirculation mode cannot be selected while in defrost mode This helps prevent window fogging For best results clear all snow and ice from the windshield before defrosting X Air Conditioning Press to turn the air conditioning system on or off An indicator light comes on to show that the air conditioning is on The air conditioning can be selected in any mode as long as the fan is on and the outside temperature is above freezing A flashing indicator light indicates that the air conditioning compressor is currently not available On hot days use the automatic fan and automatic air delivery mode settings and the vehicle will reach the desired temperature more quickly The desired fan and air delivery mode settings can still be adjusted manually Open the windows to let the hot inside air escape then close them This helps reduce the time it takes for the vehicle to cool down and helps the system to operate more efficiently The air conditioning
140. ake hydraulic system fixed since a leak means that sooner or later the brakes will not work well Do not top off the brake fluid Adding fluid does not correct a leak If fluid is added when the linings are worn there will be too much fluid when new brake linings are installed Add or remove brake fluid as necessary only when work is done on the brake hydraulic system Z CAUTION If too much brake fluid is added it can spill on the engine and burn if the engine is hot enough You or others could be burned and the vehicle could be damaged Add brake fluid only when work is done on the brake hydraulic system When the brake fluid falls to a low level the brake warning light comes on See Brake System Warning Light on page 3 31 What to Add Use only new DOT 3 brake fluid from a sealed container See Recommended Fluids and Lubricants on page 6 13 Always clean the brake fluid reservoir cap and the area around the cap before removing it This helps keep dirt from entering the reservoir Z CAUTION With the wrong kind of fluid in the brake hydraulic system the brakes might not work well This could cause a crash Always use the proper brake fluid Notice Using the wrong fluid can badly damage brake hydraulic system parts For example just a few drops of mineral based oil such as engine oil in the brake hydraulic system can damage brake hydraulic system parts so b
141. al hitches or other bumper type hitches to it Use only a frame mounted hitch that does not attach to the bumper e Will any holes be made in the body of the vehicle when the trailer hitch is installed If so be sure to seal the holes when the hitch is removed If they are not sealed deadly carbon monoxide CO from the engine s exhaust can get into the vehicle See Engine Exhaust on page 2 28 Sealing the holes will also prevent dirt and water from entering the vehicle Driving Your Vehicle Safety Chains Always attach chains between the vehicle and the trailer Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer Follow the manufacturer s recommendation for attaching safety chains and do not attach them to the bumper Always leave just enough slack so the rig can turn Never allow safety chains to drag on the ground Trailer Brakes A loaded trailer that weighs more than 1 000 lbs 450 kg needs to have its own brake system that is adequate for the weight of the trailer Be sure to read and follow the instructions for the trailer brakes so they are installed adjusted and maintained properly Because the vehicle has StabiliTrak do not try to tap into the vehicle s hydraulic brake system If you do both
142. amera provides Features and Controls An E gt gp f i p B a A View displayed by the camera B Corner of the rear bumper When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if e The RVC is turned off See Turning the Rear Camera System On or Off earlier in this section e It is dark e The sun or the beam of headlights is shining directly into the camera lens e Ice snow mud or anything else builds up on the camera lens Clean the lens rinse it with water and wipe it with a soft cloth e The back of the vehicle is in an accident the position and mounting angle of the camera can change or the camera can be affected Be sure to have the camera and its position and mounting angle checked at your dealer retailer e There are extreme temperature changes The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions If this occurs the left indicator light on the mirror will flash e A slow flash may indicate a loss of video signal or no video signal present during the reverse cycle Features and Controls e A fast flash may indicate that the display has been on for the maximum allowable time during a reverse cycle or the display has reached an Over Temperature limit The fast flash conditions are used to protect
143. an expensive repair or replacement Paying attention to the warning lights and gages could prevent injury Warning lights come on when there may be or is a problem with one of the vehicle s functions Some warning lights come on briefly when the engine is started to indicate they are working Gages can indicate when there may be or is a problem with one of the vehicle s functions Often gages and warning lights work together to indicate a problem with the vehicle When one of the warning lights comes on and stays on while driving or when one of the gages shows there may be a problem check the section that explains what to do Follow this manual s advice Waiting to do repairs can be costly and even dangerous Instrument Panel 3 27 Instrument Panel Cluster The instrument cluster is designed to indicate how the vehicle is running It shows how fast the vehicle is going about how much fuel the vehicle has left and many other things needed to drive safely and economically United States Base version shown Canada and Uplevel similar 3 28 Instrument Panel Speedometer and Odometer The speedometer shows the vehicle s speed in both miles per hour mph and kilometers per hour km h The odometer shows how far the vehicle has been driven in either miles or kilometers If the vehicle needs a new odometer installed the new one is set to the mileage total of the old odometer If it cannot it will be s
144. ance to rollover 5 59 Additionally if your vehicle has electronic systems such as anti lock brakes rollover airbags traction control and stability control the performance of these systems can be affected Z CAUTION If you add different sized wheels your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected You may increase the chance that you will crash and suffer serious injury Only use Saturn specific wheel and tire systems developed for your vehicle and have them properly installed by a Saturn certified technician See Buying New Tires on page 5 58 and Accessories and Modifications on page 5 3 for additional information 5 60 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration NHTSA which grades tires by treadwear traction and temperature performance This applies only to vehicles sold in the United States The grades are molded on the sidewalls of most passenger car tires The Uniform Tire Quality Grading UTQG system does not apply to deep tread winter type snow tires space saver or temporary Service and Appearance Care
145. and Restraint System 1 41 To tighten the belt push down on the child restraint pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor When installing a forward facing child restraint it may be helpful to use your knee to push down on the child restraint as you tighten the belt 7 If the vehicle does not have a rear seat and the child restraint has a top tether follow the child restraint manufacturer s instructions regarding the use of the top tether See Lower Anchors and Tethers for Children LATCH on page 1 31 for more information 8 Push and pull the child restraint in different directions to be sure it is secure If the airbag is off the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started If a child restraint has been installed and the on indicator is lit see If the On Indicator is Lit for a Child Restraint under Passenger Sensing System on page 1 51 for more information To remove the child restraint unbuckle the vehicle safety belt and let it return to the stowed position 1 42 Airbag System The vehicle has the following airbags A frontal airbag for the driver A frontal airbag for the right front passenger e A seat mounted side impact airbag for the driver e A seat mounted side impact airbag for the right front passenger e A roof
146. appears to be not damaged wait about five minutes and try another ignition key and check the fuse See Fuses and Circuit Breakers on page 5 80 If the engine still does not start with the other key the vehicle needs service If the vehicle does start the first key may be faulty See your dealer retailer who can service the PASS Key IIl to have a new key made In an emergency contact Roadside Assistance See Roadside Assistance Program on page 7 6 It is possible for the PASS Key IIl decoder to learn the transponder value of a new or replacement key Up to 10 keys may be programmed for the vehicle The following procedure is for programming additional keys only If all the currently programmed keys are lost or do not operate you must see your dealer retailer or a locksmith who can service PASS Key Ill to have keys made and programmed to the system See your dealer retailer or a locksmith who can service PASS Key Ill to get a new key blank that is cut exactly as the ignition key that operates the system To program the new key 1 Verify that the new key has a stamped on it 2 Insert the already programmed key in the ignition and start the engine If the engine does not start see your dealer retailer for service 3 After the engine has started turn the key to LOCK OFF and remove the key 4 Insert the key to be programmed and turn it to the ON RUN position within five seconds of the ori
147. ashes are mild and some crashes can be so serious that even buckled up a person would not survive But most crashes are in between In many of them people who buckle up can survive and sometimes walk away Without safety belts they could have been badly hurt or killed After more than 40 years of safety belts in vehicles the facts are clear In most crashes buckling up does matter a lot Seats and Restraint System Why Safety Belts Work When you ride in or on anything you go as fast as it goes Take the simplest vehicle Suppose it is just a seat on wheels Put someone on it 1 11 1 12 Seats and Restraint System Get it up to speed Then stop the vehicle The rider does not stop The person keeps going until stopped by something In a real vehicle it could be the windshield or the instrument panel or the safety belts With safety belts you slow down as the vehicle does You get more time to stop You stop over more distance and your strongest bones take the forces That is why safety belts make such good sense Seats and Restraint System Questions and Answers About Safety Belts Q Will be trapped in the vehicle after a crash if am wearing a safety belt A You could be whether you are wearing a safety belt or not But your chance of being conscious during and after an accident so you can unbuckle and get out is much greater if you are belted
148. asoline Octane on page 5 5 The services in Scheduled Maintenance on page 6 3 should be performed when indicated See Additional Required Services on page 6 6 and Maintenance Footnotes on page 6 8 for further information Z CAUTION Performing maintenance work on a vehicle can be dangerous In trying to do some jobs you can be seriously injured Do your own maintenance work only if you have the required know how and the proper tools and equipment for the job If you have any doubt see your dealer retailer to have a qualified technician do the work See Doing Your Own Service Work on page 5 4 Some maintenance services can be complex So unless you are technically qualified and have the necessary equipment have your dealer retailer do these jobs When you go to your dealer retailer for service trained and supported service technicians will perform the work using genuine parts To purchase service information see Service Publications Ordering Information on page 7 15 Owner Checks and Services on page 6 10 tells what should be checked when to check it and what can easily be done to help keep the vehicle in good condition The proper replacement parts fluids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6 13 and Maintenance Replacement Parts on page 6 15 When the vehicle is serviced make sure these are used All parts should be replaced and all neces
149. assenger Side similar The seat mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door 1 46 5 r i T k 4 SDs alll Driver Side shown Passenger Side similar The roof rail airbags for the driver right front passenger and second row outboard passengers are in the ceiling above the side windows Seats and Restraint System Z CAUTION CAUTION Continued If something is between an occupant and an airbag the airbag might not inflate properly or it might force the object into that person causing severe injury or even death The path of an inflating airbag must be kept clear Do not put anything between an occupant and an airbag and do not attach or put anything on the steering wheel hub or on or near any other airbag covering Continued Do not use seat accessories that block the inflation path of a seat mounted side impact airbag Never secure anything to the roof of a vehicle with roof rail airbags by routing a rope or tie down through any door or window opening If you do the path of an inflating roof rail airbag will be blocked When Should an Airbag Inflate Frontal airbags are designed to inflate in moderate to severe frontal or near frontal crashes to help reduce the potential for severe injuries mainly to the driver s or right front passenger s head and chest However they are only designed
150. at tire creates a drag that pulls the vehicle toward that side Take your foot off the accelerator pedal and grip the steering wheel firmly Steer to maintain lane position and then gently brake to a stop well out of the traffic lane A rear blowout particularly on a curve acts much like a skid and may require the same correction you would use in a skid In any rear blowout remove your foot from the accelerator pedal Get the vehicle under control by steering the way you want the vehicle to go 5 63 It may be very bumpy and noisy but you can still steer Gently brake to a stop well off the road if possible Z CAUTION Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training If a jack is provided with the vehicle it is designed only for changing a flat tire If it is used for anything else you or others could be badly injured or killed if the vehicle slips off the jack If a jack is provided with the vehicle only use it for changing a flat tire If a tire goes flat the next part shows how to use the jacking equipment to change a flat tire safely 5 64 Changing a Flat Tire If a tire goes flat avoid further tire and wheel damage by driving slowly to a level place Turn on the hazard warning flashers See Hazard Warning Flashers on page 3 5 Service and Appearance Care CAUTION Continued Z CAU
151. ave questions call Customer Assistance The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual See Customer Satisfaction Procedure on page 7 1 If the vehicle has rollover roof rail airbags see Different Size Tires and Wheels on page 5 59 for additional important information 1 58 Q Because have a disability have to get my vehicle modified How can find out whether this will affect my airbag system A If you have questions call Customer Assistance The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual See Customer Satisfaction Procedure on page 7 1 In addition your dealer retailer and the service manual have information about the location of the airbag sensors sensing and diagnostic module and airbag wiring Seats and Restraint System Restraint System Check Checking the Restraint Systems Safety Belts Now and then check that the safety belt reminder light safety belts buckles latch plates retractors and anchorages are all working properly Look for any other loose or damaged safety belt system parts that might keep a Safety belt system from doing its job See your dealer retailer to have it repaired Torn or frayed safety belts may not protect you ina crash They can rip apart under impact forces If a belt is torn or frayed get a new o
152. ay FAN AUX Cooling Fan RLY Auxiliary Relay Engine Control Module CAM Canister Injectors Electronic Throttle Control Relay oe Starter Relay PWR TRN RLY Service and Appearance Care Relays Usage UN RLY Run Relay R A C CLTCH Air Conditioning RLY Compressor Relay WPR SPD Windshield Wiper RLY Speed Relay HORN RLY Horn Relay WPR windshield Wiper it Control Relay ie Parking Lamp Relay 5 85 Relays Usage HDLP HI High Beam RLY Headlamp Relay HDLP LO Low Beam RLY Headlamp Relay FRT FOG Front Foglamp RLY Relay STOP LP Stoplamp Relay DEFOG RLY RLY Defogger Relay 5 86 Service and Appearance Care Capacities and Specifications For the air conditioning system refrigerant charge amount see the refrigerant caution label located under the hood See your dealer retailer for more information Air Conditioning Refrigerant R134a Service and Appearance Care 5 87 i Transmission Fluid Four Speed Automatic 6 9 qt Six Speed Automatic 9 5 qt Wheel Nut Torque 100 ft Ib 140 Nem Transmission fluid capacity is approximate See Automatic Transmission Fluid on page 5 18 for information on checking fluid level All capacities are approximate When adding be sure to fill to the approximate level as recommended in this manual Recheck fluid level after filling Engine Specifications Engine __VINGode Spark Plug Gap 2 4L L4 LES 0 040 in 1 01 mm 24 0 04
153. ay not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Instrument Panel 3 91 Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Theft Deterrent Feature THEFTLOCK is designed to discourage theft of the vehicle s radio by learning a portion of the Vehicle Identification Number VIN The radio does not operate if it is stolen or moved to a different vehicle 3 92 Instrument Panel Audio Steering Wheel Controls Some audio controls can be adjusted at the steering wheel They include the following Next Previous Press and release to go to the next or the previous preset radio station or CD track S End Call For vehicles with the OnStar system press to end a Hands Free call an OnStar call cancel an incoming call or end the Advisor Playback For vehicles with Bluetooth press to end a call or cancel an incoming call 44 54 Volume Move the thumbwheel up or down to increase or to decrease the volume ya Call Mute Press and release to mute the system Press it again to turn the sound back on For vehicles with OnStar or Bluetooth systems press and hold for longer than two seconds to interact with those systems See OnStar System on page 2 33 and Bluetooth on page 3 81
154. ayed wiping on or off Cruise Control With cruise control the vehicle can maintain a speed of about 25 mph 40 km h or more without keeping your foot on the accelerator Cruise control does not work at speeds below 25 mph 40 km h On vehicles with the StabiliTrak feature the system may begin to limit wheel spin while you are using cruise control If this happens the cruise control will automatically disengage See StabiliTrak System on page 4 7 Instrument Panel 3 9 Z CAUTION Cruise control can be dangerous where you cannot drive safely at a steady speed So do not use the cruise control on winding roads or in heavy traffic Cruise control can be dangerous on slippery roads On such roads fast changes in tire traction can cause excessive wheel slip and you could lose control Do not use cruise control on slippery roads 3 10 Instrument Panel Setting Cruise Control Z CAUTION If you leave your cruise control on when you are not using cruise you might hit a button and go into cruise when you do not want to You could be startled and even lose control Keep the cruise control switch off until you want to use cruise control The cruise control buttons are located on the left side of the steering wheel On Off Press to turn the cruise control system on and off An indicator light comes on RES Resume Accel Move the thumbwheel up to resume a
155. bag readiness light ever comes on and stays on it means that something may be wrong with the airbag system To help avoid injury to yourself or others have the vehicle serviced right away See Airbag Readiness Light on page 3 29 for more information including important safety information Seats and Restraint System If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit Ae 2 3 Turn the vehicle off Remove the child restraint from the vehicle Remove any additional items from the seat such as blankets cushions seat covers seat heaters or seat massagers Reinstall the child restraint following the directions provided by the child restraint manufacturer and refer to Securing a Child Restraint in the Right Front Seat Position on page 1 39 5 If after reinstalling the child restraint and restarting the vehicle the on indicator is still lit turn the vehicle off Then slightly recline the vehicle seatback and adjust the seat cushion if adjustable to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion Also make sure the child restraint is not trapped under the vehicle head restraint If this happens adjust the head restraint See Head Restraints on page 1 2 Restart the vehicle If the on indicator is still lit with an infant present in a child restraint secure the chi
156. be covered by the vehicle warranty Do not attach a temporary vehicle license tape a decal or anything similar to the defogger grid Remote Start Climate Control Operation For vehicles with the remote start feature and if it is activated the climate control system heats and cools the inside of the vehicle using the modes that were set before the vehicle was turned off and the rear defogger automatically turns on Automatic Climate Control System The heating cooling and ventilation for the vehicle can be controlled with this system For vehicles with the remote start feature the climate control system functions as part of the remote start feature See Remote Keyless Entry RKE System Operation on page 2 4 A B aim a am ray gt a United States version shown Canada version similar A Fan Control E Outside Air B Temperature Control F Recirculation C Air Delivery Mode Control G Rear Window Defogger D Air Conditioning Automatic Operation This climate control system automatically maintains the desired temperature inside the vehicle Do not cover the sensor located on the top of the instrument panel near the windshield or the sensor grille below the climate control faceplate These two sensors help regulate the inside air temperature AUTO Automatic Fan Turn the fan knob to AUTO for the system to automatically adjust the fan speed to reach the desired inside temperature Temperature Control
157. be left on StabiliTrak can be turned off if needed Driving Your Vehicle 4 7 we os The Traction Control System TCS StabiliTrak button is located on the instrument panel TCS can be turned off or turned on by pressing and releasing the TCS StabiliTrak button To disable both StabiliTrak and TCS press and hold the button until the TCS StabiliTrak warning light turns on solid It is recommended to leave the system on for normal driving conditions but it may be necessary to turn the system off if the vehicle is stuck in sand mud ice or snow and you want to rock the vehicle to attempt to free it StabiliTrak may also turn off automatically if it determines that a problem exists with the system 4 8 Driving Your Vehicle The TCS StabiliTrak warning light will be on solid to warn the driver that StabiliTrak is disabled and requires service If the problem does not clear itself after restarting the vehicle see your dealer retailer for service If cruise control is being used when StabiliTrak activates the cruise control automatically disengages The cruise control can be re engaged when road conditions allow See Cruise Control on page 3 9 Trailer Sway Conirol TSC The vehicle has a Trailer Sway Control TSC feature as part of the StabiliTrak system If the vehicle is towing a trailer and the system detects that the trailer is swaying the vehicle s brakes are applied without the driver pr
158. block the flow of air into the vehicle e Do not use any non GM approved hood deflectors that could adversely affect the performance of the system e Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively Passenger Compartment Air Filter The filter removes dust pollen and other airborne irritants from outside air that is pulled into the vehicle The filter should be replaced as part of routine scheduled maintenance See Scheduled Maintenance on page 6 3 for replacement intervals To find out what type of filter to use see Maintenance Replacement Parts on page 6 15 The passenger compartment air filter can be accessed by removing the entire glove box 1 Remove the six screws from around the glove box and detach the three inner clips from the glove box 2 Lower the loosened glove box housing 3 Unplug both wire cables and remove the glove box Instrument Panel 3 25 al 4 Remove the air filter cover screw 3 26 Instrument Panel 5 Remove the filter cover and pull out the old air filter 6 Install the new air filter 7 Reinstall the air filter cover Reconnect the wire cabling and re install the glove box See your dealer retailer if additional assistance is needed Warning Lights Gages and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause
159. brake systems will not work well or at all Driving with a Trailer Z CAUTION When towing a trailer exhaust gases may collect at the rear of the vehicle and enter if the liftgate trunk hatch or rear most window is open Engine exhaust contains carbon monoxide CO which cannot be seen or smelled It can cause unconsciousness and even death Continued CAUTION Continued To maximize safety when towing a trailer e Have the exhaust system inspected for leaks and make necessary repairs before starting a trip e Never drive with the liftgate trunk hatch or rear most window open e Fully open the air outlets on or under the instrument panel e Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting See Climate Control System in the Index For more information about carbon monoxide see Engine Exhaust on page 2 28 Towing a trailer requires a certain amount of experience Get to know the rig before setting out for the open road Get acquainted with the feel of handling and braking with the added weight of the trailer And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself Before starting check all trailer hitch parts and attachments safety chains electrical connectors lamps tires and mirror adjustments If the trailer has elect
160. cals California Perchlorate Materials Requirements Certain types of automotive applications such as airbag initiators seat belt pretensioners and lithium batteries contained in remote keyless transmitters may contain perchlorate materials Special handling may be necessary For additional information see www dtsc ca gov hazardouswaste perchlorate Doing Your Own Service Work Z CAUTION You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it e Be sure you have sufficient knowledge experience the proper replacement parts and tools before attempting any vehicle maintenance task e Be sure to use the proper nuts bolts and other fasteners English and metric fasteners can be easily confused If the wrong fasteners are used parts can later break or fall off You could be hurt If doing some of your own service work use the proper service manual It tells you much more about how to service the vehicle than this manual can To order the proper service manual see Service Publications Ordering Information on page 7 15 This vehicle has an airbag system Before attempting to do your own service work see Servicing Your Airbag Equipped Vehicle on page 1 56 Keep a record with all parts receipts and list the mileage and the date of any service work performed See Maintenance Record on page 6 17 Adding Equipmen
161. card or tire inflation pressure label If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label you should determine the proper tire inflation pressure for those tires As an added safety feature your vehicle has been equipped with a tire pressure monitoring system TPMS that illuminates a low tire pressure telltale when one or more of your tires is significantly under inflated Accordingly when the low tire pressure telltale illuminates you should stop and check your tires as soon as possible and inflate them to the proper pressure Driving on a significantly under inflated tire causes the tire to overheat and can lead to tire failure Under inflation also reduces fuel efficiency and tire tread life and may affect the vehicle s handling and stopping ability Please note that the TPMS is not a substitute for proper tire maintenance and it is the driver s responsibility to maintain correct tire pressure even if under inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale 5 52 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly The TPMS malfunction indicator is combined with the low tire pressure telltale When the system detects a malfunction the telltale will flash for approximately one minute and then remain continuo
162. ccurs To help avoid injury to you and others e Dispense fuel only into approved containers e Do not fill a container while it is inside a vehicle ina vehicle s trunk pickup bed or on any surface other than the ground Continued Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle Contact should be maintained until the filling is complete Do not smoke while pumping fuel Do not use a cellular phone while pumping fuel Checking Things Under the Hood Z CAUTION An electric fan under the hood can start up and injure you even when the engine is not running Keep hands clothing and tools away from any underhood electric fan Z CAUTION Things that burn can get on hot engine parts and start a fire These include liquids like fuel oil coolant brake fluid windshield washer and other fluids and plastic or rubber You or others could be burned Be careful not to drop or spill things that will burn onto a hot engine Service and Appearance Care 5 11 Hood Release To open the hood do the following 1 Pull the handle with this symbol on it It is located under the instrument panel on the driver side of the vehicle 2 Then go to the front of the vehicle and lift up on the secondary hood release lever 3 Lift the hood Before closing the hood be sure all the filler caps are on properly Then pull
163. ched In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached Be sure to read and follow the instructions for your child restraint If the child restraint does not have a top tether one can be obtained in kit form for many child restraints Ask the child restraint manufacturer whether or not a kit is available Seats and Restraint System Lower Anchor and Top Tether Anchor Locations Hh ah at Rear Seat Top Tether Anchor Seating positions with top tether anchors Lower Anchor Seating positions with two lower anchors 1 33 To assist you in locating the lower anchors each seating position with lower anchors has two labels near the crease between the seatback and the seat cushion Hs To assist you in locating the top tether anchors the top tether anchor symbol is located near the top tether anchors The top tether anchors are located on the back of the rear seatback Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed 1 34 Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached or if the instructions that come with the child restraint say that the top tether must be attached Accident statistics show that children are safer if they are restrain
164. cle or because of what the repair costs were For frontal airbags inflation is determined by what the vehicle hits the angle of the impact and how quickly the vehicle slows down For seat mounted side impact and roof rail airbags deployment is determined by the location and severity of the side impact Ina rollover event roof rail airbag deployment is determined by the direction of the roll What Makes an Airbag Inflate In a deployment event the sensing system sends an electrical signal triggering a release of gas from the inflator Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy The inflator the airbag and related hardware are all part of the airbag module Frontal airbag modules are located inside the steering wheel and instrument panel For vehicles with seat mounted side impact airbags there are airbag modules in the side of the front seatbacks closest to the door For vehicles with roof rail airbags there are airbag modules in the ceiling of the vehicle near the side windows that have occupant seating positions Seats and Restraint System How Does an Airbag Restrain In moderate to severe frontal or near frontal collisions even belted occupants can contact the steering wheel or the instrument panel In moderate to severe side collisions even belted occupants can contact the inside of the vehicle Airbags supplement the protection provided by
165. compressor is automatically turned off When the coolant temperature returns to normal the A C operation automatically resumes You can continue to drive your vehicle ENGINE OVERHEATED IDLE ENGINE Notice lf you drive your vehicle while the engine is overheating severe engine damage may occur If an overheat warning appears on the instrument panel cluster and or DIC stop the vehicle as soon as possible Do not increase the engine speed above normal idling speed See Engine Overheating on page 5 25 for more information This message displays when the engine coolant temperature is too hot Stop and allow the vehicle to idle until it cools down 3 52 Instrument Panel ENGINE OVERHEATED STOP ENGINE Notice lf you drive your vehicle while the engine is overheating severe engine damage may occur If an overheat warning appears on the instrument panel cluster and or DIC stop the vehicle as soon as possible See Engine Overheating on page 5 25 for more information This message displays along with a continuous chime when the engine has overheated Stop and turn the engine off immediately to avoid severe engine damage See Engine Overheating on page 5 25 ENGINE POWER IS REDUCED This message displays when the vehicle s engine power is reduced Reduced engine power can affect the vehicle s ability to accelerate If this message is on but there is no reduction in performance proceed to your destination
166. continue to remain unsatisfied after following the procedure outlined in Steps One and Two Saturn and its retailers offer the additional assistance of a neutral party through our voluntary participation in a mediation arbitration program called Better Business Bureau BBB Auto Line The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty This program is available at no cost to you our customer Although you may be required to resort to this informal dispute resolution program prior to filing a court action use of the program is free of charge and your case is generally heard within 40 days If you do not agree with the decision given in your case you can reject it and proceed with any other venue for relief available to you Contact the BBB Auto Line Program by using the toll free telephone number or by writing them at the following address BBB Auto Line Program Council of Better Business Bureaus Inc 4200 Wilson Boulevard Suite 800 Arlington VA 22203 1838 Telephone 1 800 955 5100 dr bbb org goauto Customer Assistance Information This program is available in all 50 states and the District of Columbia Eligibility is limited by vehicle age mileage and other factors Saturn Corporation reserves the right to change eligibility limitations
167. could startle and confuse you or make you push a pedal when you do not want to Adjust the driver s seat only when the vehicle is not moving To move a manual seat forward or rearward E i i pe AN a et i Se i i w j SLR i i k 1 Lift the bar to unlock the seat 2 Slide the seat to the desired position and release the bar Try to move the seat with your body to be sure the seat is locked in place 1 4 Seats and Restraint System Seat Height Adjuster If the vehicle has a manual driver seat height adjuster it is located on the outboard side of the seat near the front of the seat cushion To raise the seat move the lever upward repeatedly until the seat is at the desired height To lower the seat move the lever downward repeatedly until the seat is at the desired height Power Seat d To adjust the seat Zz AG a Bi a Move the seat forward or rearward Raise or lower the front or rear part of the seat cushion Manual Lumbar If the vehicle has this feature the knob is located on the inboard side of the driver seatback Seats and Restraint System 1 5 Turn the knob clockwise or counterclockwise to increase or decrease the lumbar support Heated Seats On vehicles with heated front seats the controls are located on the center console The engine must be running to operate the heated seats w Heated Seat Press this button t
168. coverage is not available from your current insurance carrier consider switching to another insurance carrier If your vehicle is leased the leasing company may require you to have insurance that assures repairs with Genuine GM Original Equipment Manufacturer OEM parts or Genuine Manufacturer replacement parts Read your lease carefully as you may be charged at the end of your lease for poor quality repairs 7 12 If a Crash Occurs Here is what to do if you are involved in a crash e Check to make sure that you are all right If you are uninjured make sure that no one else in your vehicle or the other vehicle is injured e If there has been an injury call emergency services for help Do not leave the scene of a crash until all matters have been taken care of Move your vehicle only if its position puts you in danger or you are instructed to move it by a police officer e Give only the necessary and requested information to police and other parties involved in the crash Do not discuss your personal condition mental frame of mind or anything unrelated to the crash This will help guard against post crash legal action Customer Assistance Information If you need roadside assistance call GM Roadside Assistance See Roadside Assistance Program on page 7 6 for more information If your vehicle cannot be driven know where the towing service will be taking it Get a card from the tow truck operator
169. covers seat heaters and seat massagers can affect how well the passenger sensing system operates We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your specific vehicle See Adding Equipment to Your Airbag Equipped Vehicle on page 1 57 for more information about modifications that can affect how the system operates Z CAUTION Stowing of articles under the passenger seat or between the passenger seat cushion and seatback may interfere with the proper operation of the passenger sensing system Seats and Restraint System Servicing Your Airbag Equipped Vehicle Airbags affect how the vehicle should be serviced There are parts of the airbag system in several places around the vehicle Your dealer retailer and the service manual have information about servicing the vehicle and the airbag system To purchase a service manual see Service Publications Ordering Information on page 7 15 Z CAUTION For up to 10 seconds after the ignition is turned off and the battery is disconnected an airbag can still inflate during improper service You can be injured if you are close to an airbag when it inflates Avoid yellow connectors They are probably part of the airbag system Be sure to follow proper service procedures and make sure the person performing work for you is qualified to do so Adding Equipment to Your Airbag Equipped V
170. ct to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment PASS Key Ill uses a radio frequency transponder in the key that matches a decoder in the vehicle 2 14 PASS Key Ill Electronic Immobilizer Operation This vehicle has PASS Key Ill Personalized Automotive Security System theft deterrent system PASS Key Ill is a passive theft deterrent system The system is automatically armed when the key is removed from the ignition You do not have to manually arm or disarm the system The security light comes on if there is a problem with arming or disarming the theft deterrent system When the PASS Key Ill system senses that someone is using the wrong key it prevents the vehicle from starting Anyone using a trial and error method to start the vehicle will be discouraged because of the high number of electrical key codes Features and Controls When trying to start the vehicle if the engine does not start and the security light on the instrument panel cluster comes on there may be a problem with your theft deterrent system Turn the ignition off and try again If the engine still does not start and the key
171. d Features and Controls OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area OnStar service also cannot work unless the vehicle is in a place where the wireless service provider OnStar has hired for that area has coverage network capacity and reception when the service is needed and technology that is compatible with the OnStar service Not all services are available everywhere particularly in remote or enclosed areas or at all times Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available The vehicle must have a working electrical system including adequate battery power for the OnStar equipment to operate There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place Some examples are damage to important parts of the vehicle in a crash hills tall buildings tunnels weather or wireless phone network congestion Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard If the light next to the OnStar buttons is red the system may not be functioning properly Press the OnStar button and request a vehicle diagnostic If the light appears clear no light is appearing your OnStar subscription has expired and all services have been deactivated Pr
172. d riding in a rear facing child restraint a child riding in a forward facing child seat an older child riding in a booster seat and children who are large enough using safety belts A label on the sun visor says Never put a rear facing child restraint in the front This is because the risk to the rear facing child is so great if the airbag deploys Seats and Restraint System Z CAUTION CAUTION Continued A child in a rear facing child restraint can be seriously injured or killed if the right front passenger airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag A child in a forward facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position Even if the passenger sensing system has turned off the right front passenger frontal airbag no system is fail safe No one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off Continued Secure rear facing child restraints in a rear seat even if the airbag is off If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go Itis better to secure the child restraint in a rear seat See Passenger Sensing System on page 1 51 for additional information
173. d by a tone 3 Say the complete phone number to be stored at once with no pauses e Ifthe system recognizes the number it responds with OK Storing and repeats the phone number e Ifthe system is unsure it recognizes the phone number it responds with Store and repeats the number followed by Please say yes or no If the number is correct say Yes If the number is not correct say No The system will ask for the number to be re entered 4 After the system stores the phone number it responds with Please say the name tag followed by a tone 5 Say a name tag for the phone number The name tag is recorded and the system responds with About to store lt name tag gt Does that sound OK e Ifthe name tag does not sound correct say No and repeat Step 5 e Ifthe name tag sounds correct say Yes and the name tag is stored After the number is stored the system returns to the main menu Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Digit Store The system responds with Please say the first digit to store followed by a tone 3 Say the first digit to be stored The system will repeat back the digit it heard followed by a tone Continue entering digit
174. d where you want Replace your spare with a full size tire as soon as you can Notice When the compact spare is installed do not take the vehicle through an automatic car wash with guide rails The compact spare can get caught on the rails which can damage the tire wheel and other parts of the vehicle Do not use your compact spare on other vehicles Do not mix your compact spare tire or wheel with other wheels or tires Keep your spare tire and its wheel together Notice Tire chains will not fit the compact spare Using them can damage the vehicle and can damage the chains too Do not use tire chains on the compact spare 5 72 Appearance Care Interior Cleaning The vehicle s interior will continue to look its best if it is cleaned often Although not always visible dust and dirt can accumulate on the upholstery Dirt can damage carpet fabric leather and plastic surfaces Regular vacuuming is recommended to remove particles from the upholstery It is important to keep the upholstery from becoming and remaining heavily soiled Soils should be removed as quickly as possible The vehicle s interior may experience extremes of heat that could cause stains to set rapidly Lighter colored interiors may require more frequent cleaning Use care because newspapers and garments that transfer color to home furnishings may also transfer color to the vehicle s interior Service and Appearance Care When c
175. dealer retailer check your cooling system Notice If extra inhibitors and or additives are used in the vehicle s cooling system the vehicle could be damaged Use only the proper mixture of the engine coolant listed in this manual for the cooling system See Recommended Fluids and Lubricants on page 6 13 for more information 5 24 Service and Appearance Care Checking Coolant The surge tank is located on the driver side of the engine compartment See Engine Compartment Overview on page 5 12 for more information on location Z CAUTION Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly Never turn the surge tank pressure cap even a little when the engine and radiator are hot The vehicle must be on a level surface When your engine is cold the coolant level should be between the MIN and MAX lines Adding Coolant If you need more coolant add the proper DEX COOL coolant mixture at the surge tank but only when the engine is cool See Cooling System on page 5 19 for instructions on How to Add Coolant to the Coolant Surge Tank Z CAUTION You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine When replacing the pressure cap make sure i
176. driver side rear tire The driver side rear turn signal lamp comes on Repeat the procedure in Step 5 The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire and the TPMS sensor matching process is no longer active Turn the ignition switch to LOCK OFF 10 Set all four tires to the Ti recommended air pressure level as indicated on the Tire and Loading Information label Put the valve caps back on the valve stems 5 56 Tire Inspection and Rotation We recommend that you regularly inspect the vehicle s tires including the spare tire for signs of wear or damage See When It Is Time for New Tires on page 5 57 for more information Tires should be rotated every 5 000 to 8 000 miles 8 000 to 13 000 km See Scheduled Maintenance on page 6 3 The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle This will ensure that the vehicle continues to perform most like it did when the tires were new Any time you notice unusual wear rotate the tires as soon as possible and check wheel alignment Also check for damaged tires or wheels Service and Appearance Care See When It Is Time for New Tires on page 5 57 and Wheel Replacement on page 5 62 U S When rotating the vehicle s tires always use the correct rotation pattern shown here Do not include the compact spare tire in the tire ro
177. e press the button on the Remote Keyless Entry RKE transmitter twice or the power door lock switch To open the liftgate press the touchpad on the underside of the liftgate handle and pull up To close the liftgate pull down using the handle and close until it latches Features and Controls 2 9 Liftgate Operation with Loss of Power b gt To open the liftgate if the vehicle s battery is disconnected or the voltage is low access the release lever Remove the interior trim cover on the inside of the liftgate Use a tool to push the lever on the latch until the liftgate releases 2 10 Features and Controls Windows Power Windows Z CAUTION Z CAUTION Leaving children helpless adults or pets in a vehicle with the windows closed is dangerous They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke Never leave a child a helpless adult or a pet alone in a vehicle especially with the windows closed in warm or hot weather Leaving children in a vehicle with the keys is dangerous for many reasons children or others could be badly injured or even killed They could operate the power windows or other controls or even make the vehicle move The windows will function and they could be seriously injured or killed if caught in the path of a closing window Do not leave keys in a vehicle with children When there are childre
178. e the headlamps will turn on automatically if the exterior lamp control is in the AUTO position and the wipers are active Notice Going through an automatic car wash with the wipers on can damage them Turn the wipers off when going through an automatic car wash Windshield Washer Z CAUTION In freezing weather do not use your washer until the windshield is warmed Otherwise the washer fluid can form ice on the windshield blocking your vision Pull the windshield wiper lever toward you to spray washer fluid on the windshield The wipers will run for a few cycles to clear the windshield For more wash cycles pull the lever forward and hold Heated Windshield Washer Nozzles This feature prevents the windshield washer fluid from freezing on the nozzle during cold conditions The heated nozzles are turned on when the rear window defogger is activated See Automatic Climate Control System on page 3 20 Rear Window Wiper Washer The rear wiper and rear wash button is located on the instrument panel above the climate control system 6 amp 5 Rear Wiper Washer Press to wash and wipe the rear window The rear window washer uses the same reservoir as the windshield washer Check the windshield washer reservoir level if the front windshield can be worked but no fluid is sprayed when the rear washer is activated See Windshield Washer Fluid on page 5 27 bA Delay Press to turn the del
179. e the tether over the seatback 1 36 Seats and Restraint System If the position you are using does not have a headrest or head restraint and you are using a dual tether route the tether over the seatback If the position you are using has an adjustable headrest or head restraint and you are using a dual tether route the tether around the headrest or head restraint If the position you are using has an adjustable headrest or head restraint and you are using a single tether raise the headrest or head restraint and route the tether under the headrest or head restraint and in between the headrest or head restraint posts 3 Push and pull the child restraint in different directions to be sure it is secure Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position study the instructions that came with the child restraint to make sure it is compatible with this vehicle If the child restraint has the LATCH system see Lower Anchors and Tethers for Children LATCH on page 1 31 for how and where to install the child restraint using LATCH If a child restraint is secured in the vehicle using a safety belt and it uses a top tether see Lower Anchors and Tethers for Children LATCH on page 1 31 for top tether anchor locations Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether
180. e a piece of cardboard or equivalent in front of the headlamp not being adjusted This allows only the beam of light from the headlamp being adjusted to be seen on the flat surface Service and Appearance Care 7 Locate the vertical headlamp aiming screws which are under the hood near each headlamp assembly The adjustment screw can be turned with a E8 Torx socket 8 Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line Turn it clockwise or counterclockwise to raise or lower the angle of the beam i yo g sigh ig heh 9 Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line The lamp on the left A shows the correct headlamp aim The lamp on the right B shows the incorrect headlamp aim 10 Repeat Steps 7 through 9 for the opposite headlamp Bulb Replacement For the proper type of replacement bulbs see Replacement Bulbs on page 5 41 For any bulb changing procedure not listed in this section contact your dealer retailer Halogen Bulbs Z CAUTION Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb You or others could be injured Be sure to read and follow the instructions on the bulb package Service and Appearance Care Headlamps To replace one of the headlamp bulbs use the following procedure To replace the parking turn signal
181. e cleaned regularly to keep their luster Washing with water is all that is usually needed However chrome polish may be used on chrome or stainless steel trim if necessary Use special care with aluminum trim To avoid damaging protective trim never use auto or chrome polish steam or caustic soap to clean aluminum A coating of wax rubbed to high polish is recommended for all bright metal parts Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent Wash the windshield thoroughly when cleaning the blades Bugs road grime sap and a buildup of vehicle wash wax treatments may cause wiper streaking Replace the wiper blades if they are worn or damaged Wipers can be damaged by e Extreme dusty conditions Sand and salt e Heat and sun e Snow and ice without proper removal Aluminum Wheels Notice Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium calcium or sodium chloride These chlorides are used on roads for conditions such as ice and dust Always wash the vehicle s chrome with soap and water after exposure Notice Using strong soaps chemicals abrasive polishes cleaners brushes or cleaners that contain acid on aluminum or chrome plated wheels could
182. e could move suddenly If the vehicle moves you or others could be injured 1 Before starting this check be sure there is enough room around the vehicle 2 Firmly apply both the parking brake and the regular brake See Parking Brake on page 2 24 Do not use the accelerator pedal and be ready to turn off the engine immediately if it starts Maintenance Schedule 3 For automatic transmission vehicles try to start the engine in each gear The vehicle should start only in P Park or N Neutral If the vehicle starts in any other position contact your dealer retailer for service For manual transmission vehicles put the shift lever in Neutral push the clutch pedal down halfway and try to start the engine The vehicle should start only when the clutch pedal is pushed down all the way to the floor If the vehicle starts when the clutch pedal is not pushed all the way down contact your dealer retailer for service 6 11 Automatic Transmission Shift Lock Control System Check Z CAUTION When you are doing this inspection the vehicle could move suddenly If the vehicle moves you or others could be injured 1 Before starting this check be sure there is enough room around the vehicle It should be parked on a level surface 2 Firmly apply the parking brake See Parking Brake on page 2 24 Be ready to apply the regular brake immediately if the vehicle begins to move
183. e effectiveness of soil removal e Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt For liquid cleaners about 20 drops per gallon 3 78 L of water is a good guide Use only mild neutral pH soaps e Too much cleaner that saturates the upholstery e Organic solvents such as naptha alcohol etc that can damage the vehicle s interior Service and Appearance Care Fabric Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats For any soil always try to remove it first with plain water or club soda Before cleaning gently remove as much of the soil as possible using one of the following techniques e For liquids gently blot the remaining soil with a paper towel Allow the soil to absorb into the paper towel until no more can be removed e For solid dry soils remove as much as possible and then vacuum To clean 1 Saturate a lint free clean white cloth with water or club soda 2 Wring the cloth to remove excess moisture 5 73 3 Start on the outside edge of the soil and gently rub toward the center Continue cleaning using a clean area of the cloth each time it becomes soiled 4 Continue to gently rub the soiled area until the cleaning cloth remains clean 5 If the soil is not co
184. e hood can start up even when the engine is not running and can cause injury Keep hands clothing and tools away from any underhood electric fan If the coolant inside the coolant surge tank is boiling do not do anything else until it cools down The vehicle should be parked ona level surface 5 20 The coolant level should be between the MIN and MAX lines If it is not you may have a leak at the radiator hoses heater hoses radiator water pump or somewhere else in the cooling system Z CAUTION Heater and radiator hoses and other engine parts can be very hot Do not touch them If you do you can be burned Do not run the engine if there is a leak If you run the engine it could lose all coolant That could cause an engine fire and you could be burned Get any leak fixed before you drive the vehicle Service and Appearance Care If there seems to be no leak with the engine on check to see if the electric engine cooling fan is running If the engine is overheating the fan should be running If it is not your vehicle needs service Turn off the engine Notice Engine damage from running the engine without coolant is not covered by the warranty Notice Using coolant other than DEX COOL can cause premature engine heater core or radiator corrosion In addition the engine coolant could require changing sooner at 30 000 miles 50 000 km or 24 months whichever occ
185. e ignition is in ON RUN QW Rear Window Defogger Press to turn the rear window defogger on or off An indicator light on the button comes on to show that it is activated The rear window defogger stays on for approximately 10 minutes after the button is pressed unless the ignition is turned to ACC ACCESSORY or LOCK OFF If turned on again the defogger only runs for approximately five minutes before turning off At higher vehicle speeds the defogger may stay on continuously The defogger can also be turned off by turning off the engine 3 24 Instrument Panel For vehicles with the remote start feature the rear defogger will automatically turn on when remote start is activated Notice Do not use anything sharp on the inside of the rear window If you do you could cut or damage the warming grid and the repairs would not be covered by the vehicle warranty Do not attach a temporary vehicle license tape a decal or anything similar to the defogger grid Remote Start Climate Control Operation For vehicles with the remote start feature and if it is activated the climate control system heats and cools the inside of the vehicle using the modes that were set before the vehicle was turned off Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airflow Operation Tips e Clear away any ice snow or leaves from the air inlets at the base of the vehicle that may
186. e steering wheel Pull down on the handle to access Sunglasses Storage Compartment Your vehicle may have a sunglasses storage compartment located near the rearview mirror Push the cover to open Features and Controls Front Storage Area For vehicles with a storage area located under the front passenger seat lift up on the end of the tray and pull it forward to access it Center Console Storage Your vehicle has a center console with an upper lower and rear storage area To access the upper storage area lift up on the top lever To access the lower storage area lift up on the bottom lever The top of the center console can extend forward To adjust hold the top of the lever up and pull the top of the center console forward To open the cover of the rear storage area push the button located at the top Luggage Carrier Z CAUTION If something is carried on top of the vehicle that is longer or wider than the luggage carrier like paneling plywood or a mattress the wind can catch it while the vehicle is being driven This can cause a driver to lose control The item being carried could be violently torn off and this could cause a collision and damage the vehicle Items may be carried inside Never carry something longer or wider than the luggage carrier on top of the vehicle Features and Controls 2 43 If your vehicle has a luggage carrier items can be lo
187. e this vehicle correctly may result in loss of control or an accident Be sure to read the on pavement and off road driving guidelines which follow in this manual in the section called Your Driving the Road and Your Vehicle and specifically Off Road Driving on page 4 13 2008 General Motors Corporation All Rights Reserved Index To quickly locate information about the vehicle use the index in the back of the manual It is an alphabetical list of what is in the manual and the page number where it can be found Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means Do Not Do not do this or Do not let this happen A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning Z CAUTION These mean there is something that could hurt you or other people Cautions tell what the hazard is and what to do to avoid or reduce the hazard Read these cautions A notice tells about something that can damage the vehicle Notice These mean there is something that could damage your vehicle Many times this damage would not be covered by the vehicle s warranty and it could be costly The notice tells what to do to help avoid the damage There are also warning labels on the vehicle which use the same words CAUTION or Notice Preface iii Vehicle Symbols
188. e vehicle has electronic frontal sensors which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact For moderate frontal impacts dual stage airbags inflate at a level less than full deployment For more severe frontal impacts full deployment occurs 1 48 The vehicle has seat mounted side impact and roof rail airbags See Airbag System on page 1 42 Seat mounted side impact and roof rail airbags are intended to inflate in moderate to severe side crashes In addition these roof rail airbags are intended to inflate during a rollover or in a severe frontal impact Seat mounted side impact and roof rail airbags will inflate if the crash severity is above the system s designed threshold level The threshold level can vary with specific vehicle design Seats and Restraint System Seat mounted side impact airbags are not intended to inflate in frontal impacts near frontal impacts rollovers or rear impacts Roof rail airbags are not intended to inflate in rear impacts A seat mounted side impact airbag is intended to deploy on the side of the vehicle that is struck Both roof rail airbags will deploy when either side of the vehicle is struck or if the sensing system predicts that the vehicle is about to roll over or in a severe frontal impact In any particular crash no one can say whether an airbag should have inflated simply because of the damage to a vehi
189. e working If this happens see your dealer retailer for service Traction Control System TCS Warning Light ee OFF The Traction Control System TCS Warning Light shows one of these two symbols This light comes on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer It also comes on when the Traction Control System TCS has been turned off or when the Electronic Stability Program ESP is not ready If there is a problem with the TCS or the ESP this light and the TCS warning light comes on at the same time See Traction Control System TCS on page 4 8 and StabiliTrak System on page 4 7 for more information Instrument Panel 3 33 StabiliTrak Indicator Light AN ee The StabiliTrak light comes on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer This light flashes while the StabiliTrack or the Traction Control System TCS is working The light comes on when the ESP has been turned off and if there is a problem with the StabiliTrak or the TCS See Traction Control System TCS on page 4 8 and StabiliTrak System on page 4 7 for more information 3 34 Instrument Panel Engine Coolant Temperature Warning Light The engine coolant temperature light should come on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer
190. e00 5 8 Filling a Portable Fuel Container ceseceeeeeeeeeeeeeees 5 10 Service and Appearance Care Checking Things Under the Hood Checking Things Under the HOOG 2s ccesissssscccenadeaed 5 10 Hood Release eseeeeeeeee 5 11 Engine Compartment OVOCIVIGW ses eeceeeverswen dem tebe 5 12 Engine Qil sest ireren ensia 5 14 Engine Oil Life System 5 16 Engine Air Cleaner Filter 5 17 Automatic Transmission Fluid Cooling System Engine Coolant Coolant Surge Tank Pressure Cap c seceeeeeee 5 25 Engine Overheating eee 5 25 Power Steering Fluid 5 26 Windshield Washer Fluid 5 27 Brakes ss tiesecndccetadanncaveamaamen 28 Battery ecseri teeina 5 30 Jump Starting vertencgesecncerae 5 31 All Wheel Drive All Wheel Drive 0006 5 35 Headlamp Aiming Headlamp Aiming 5 36 Bulb Replacement Bulb Replacement Halogen Bulbs Headlamps Front Turn Signal and Parking Lamps Taillamps Turn Signal Stoplamps and Back up LAMPS 0 eee eect teeta License Plate Lamp Replacement Bulbs Windshield Wiper Blade Replacement Windshield Wiper Blade Replacement Tires l a SE E EE E EE Tire Sidewall Labeling Tire Terminology and Definitions 220eeeeeeeeeees Inflation Tire Pressure High Speed Operation Tire Pressure Monitor System Tire Pressure Monitor Operation ANEN ET E E 5 2 Tire Inspection and Rotation When It Is Time for N
191. ecsicisd 5 30 Electric Power Management 4 3 15 Run Down Protection 3 16 Belt Routing Engine 6 16 Bluetooth oiii 3 81 Brake Emergencies 0 00 4 6 Brake Fluid c0eeee ee 5 28 Brakes ccjsienesyeaien neeecdaheseae 5 28 ANUIOCK innascceiniecsabedaacnes steed 4 6 Parking asscchsnacetetencmeancanate 2 24 System Warning Light 3 31 Braking zepoa onerare etaa 4 5 Braking in Emergencies 4 6 Break In New Vehicle 2 15 Bulb Replacement 5 41 Fog Lamp icivecisiceitiocns 3 14 Front Turn Signal and Parking Lamps 5 40 Halogen Bulbs 5 39 Headlamp Aiming 5 36 Headlamps eeeeeeee 5 39 License Plate Lamps 5 41 Taillamps Turn Signal Stoplamps and Back up LAMPS iore 5 40 Buying New Tires 0 5 58 C Calibration o 3 47 California Perchlorate Materials Requirements 5 4 California Fuel ceeee 5 6 California Proposition 65 WARNING wet ccevaecredinedent gece 5 4 Camera Rear Vision Canadian Owners Capacities and Specifications 5 Carbon Monoxide Engine Exhaust Liftgate Winter Driving Care of Safety Belts 000 Cargo Tie Downs 2 2 2000 Cargo Cover Cargo Management System CD MP3 Center Console Storage
192. ed in the rear rather than the front seat See Where to Put the Restraint on page 1 30 for additional information Seats and Restraint System Securing a Child Restraint Designed for the LATCH System Z CAUTION Z CAUTION If a LATCH type child restraint is not attached to anchors the child restraint will not be able to protect the child correctly In a crash the child could be seriously injured or killed Install a LATCH type child restraint properly using the anchors or use the vehicle s safety belts to secure the restraint following the instructions that came with the child restraint and the instructions in this manual Do not attach more than one child restraint to a single anchor Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash A child or others could be injured To reduce the risk of serious or fatal injuries during a crash attach only one child restraint per anchor Z CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten Buckle any unused safety belts behind the child restraint so children cannot reach them Pull the shoulder belt all the way out of the retractor to set the lock if your vehicle has one after the child restraint has been installed Notice Do not let the
193. ed using the remote start feature if the key is in the ignition the hood is open or if there is an emission control system malfunction The engine turns off during a remote start if the coolant temperature gets too high or if the oil pressure gets low Remote Start Ready If the vehicle does not have the remote vehicle start feature it may have the remote start ready feature This feature allows your dealer retailer to add the manufacturer s remote vehicle start feature To add the manufacturer s remote vehicle start feature to the vehicle see your dealer retailer Doors and Locks Door Locks Z CAUTION Unlocked doors can be dangerous e Passengers especially children can easily open the doors and fall out of a moving vehicle When a door is locked the handle will not open it The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked So all passengers should wear Safety belts properly and the doors should be locked whenever the vehicle is driven Continued Features and Controls 2 7 CAUTION Continued e Young children who get into unlocked vehicles may be unable to get out A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke Always lock the vehicle whenever leaving it e Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle Locki
194. ee 2 4 Keyless Entry System 2 3 KEYS iichsdnsielaticgnertadiegtcennets 2 2 L Labeling Tire Sidewall 5 44 Lamp Malfunction Indicator 3 35 Lamps Daytime Running DRL 3 13 DOME weve 2 iatdecaweaesdiees 3 14 Front Turn Signal and Parking Lamps 5 40 License Plate 5 41 REAGING scccininarnererias 3 15 Lap Shoulder Belt 1 19 LATCH System for Child Restraints 00 0 0 cee 1 31 Liftgate Carbon Monoxide 2 9 Lighting BEAUV eioten 3 14 Lights Airbag Readiness All Wheel Drive Disabled Antilock Brake System ABS Warning Brake System Warning Change Engine Oil Charging System Cruise Control Daytime Running Lamps Indicator siensa DOOM Al al ssnin siete Engine Coolant Temperature Warning Exterior Lamps Flash to Pass 0085 Fog LAMP naciscacizevecs teases Gate Ajar eeee Highbeam On eeeeee High Low Beam Changer Low Fuel Warning Low Washer Fluid Warning Oil Pressure 0008 Passenger Airbag Status INDICATOR siese Lights cont Reduced Engine Power 3 39 Safety Belt Reminders 3 28 SECUMILY eiriaa renano 3 38 Service Vehicle Soon 3 40 StabiliTrak Indicator 3 33 Tire Pressure 006 3 34 Traction Control System TCS Warning 3 33 Warning Power Steering
195. eesti ciweeoeiemeeeeies 3 40 All Wheel Drive AWD SYSTEM ienei ri 4 9 Antenna Fixed Mast aaen 3 93 Antenna XM Satellite Radio Antenna System 3 93 Antilock Brake System ABS 0 eeeeeeee 4 6 Warning Light 3 32 INDEX Appearance Care Aluminum Wheels Care of Safety Belts Chemical Paint Spotting Cleaning Exterior Lamps Lenses Fabric Carpet Finish Care 0 0 00ee Finish Damage 5 Instrument Panel Vinyl and Other Plastic Surfaces Interior Cleaning Leather Sheet Metal Damage MMOS erpe Underbody Maintenance Washing Your Vehicle Weatherstrips 4 Windshield and Wiper Blades c icccseteterasccnsete es Assistance Program Roadside Audio System a Audio Steering Wheel COMMONS ihent Navigation Radio System see Navigation Manual i 1 i 2 INDEX Audio System cont Setting the Clock 3 65 XM Satellite Radio Antenna System 3 93 Audio System s 1eee 3 67 Audio Systems Radio Reception 3 92 Theft Deterrent Feature 3 91 Automatic Climate Control System aiic 3 20 Automatic Door Lock 2 8 Automatic Door Unlock 2 8 Automatic Headlamp SYSTEM s ccttercnedaeden 3 13 Automatic Transmission O scien 2545 adenine ten ses dhe 5 18 Operation 2 19 2 22 B Battery siciiiecissdidelectedar
196. egin speaking to answer the call e Press to ignore a call 3 88 Instrument Panel Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work Press to answer an incoming call when another call is active The original call is placed on hold Press again to return to the original call To ignore the incoming call continue with the original call with no action Press to disconnect the current call and switch to the call on hold Three Way Calling Three Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work 1 While on a call press X The system responds with Ready followed by a tone 2 Say Three way call The system responds with Three way call please say dial or call 3 Use the dial or call command to dial the number of the third party to be called 4 Once the call is connected press to link all the callers together Ending a Call Press to end a call Muting a Call During a call all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them To Mute a call 1 Press The system responds with Ready followed by a tone 2 Say Mute Call The system responds with Call muted To Cancel Mute 1 Press The system
197. ehicle Q Is there anything might add to or change about the vehicle that could keep the airbags from working properly A Yes If you add things that change the vehicle s frame bumper system height front end or side sheet metal they may keep the airbag system from working properly Changing or moving any parts of the front seats safety belts the airbag sensing and diagnostic module steering wheel instrument panel roof rail airbag modules ceiling headliner or pillar garnish trim front sensors side impact sensors rollover sensor module or airbag wiring can affect the operation of the airbag system Seats and Restraint System 1 57 In addition the vehicle has a passenger sensing system for the right front passenger position which includes sensors that are part of the passenger seat The passenger sensing system may not operate properly if the original seat trim is replaced with non GM covers upholstery or trim or with GM covers upholstery or trim designed for a different vehicle Any object such as an aftermarket seat heater or a comfort enhancing pad or device installed under or on top of the seat fabric could also interfere with the operation of the passenger sensing system This could either prevent proper deployment of the passenger airbag s or prevent the passenger sensing system from properly turning off the passenger airbag s See Passenger Sensing System on page 1 51 If you h
198. ellite Radio Antenna System 3 93 Y Your Driving the Road and Your Vehicle 4 1 Your Vehicle and the Environment 0 eee 6 1
199. em needs to be reset again What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer Do not let used oil stay on your skin for very long Clean your skin and nails with soap and water or a good hand cleaner Wash or properly dispose of clothing or rags containing used engine oil See the manufacturer s warnings about the use and disposal of oil products Used oil can be a threat to the environment If you change your own oil be sure to drain all the oil from the filter before disposal Never dispose of oil by putting it in the trash pouring it on the ground into sewers or into streams or bodies of water Recycle it by taking it to a place that collects used oil Service and Appearance Care Engine Air Cleaner Filter See Engine Compartment Overview on page 5 12 for the location of the engine air cleaner filter When to Inspect the Engine Air Cleaner Filter Inspect the air cleaner filter at the Maintenance II intervals and replace it at the first oil change after each 50 000 mile 80 000 km interval See Scheduled Maintenance on page 6 3 for more information If you are driving in dusty dirty conditions inspect the filter at each engine oil change How to Inspect the Engine Air Cleaner Filter To inspect the air cleaner filter remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt If the fil
200. em is designed to work properly under a wide range of conditions including off road usage Always wear your safety belt and observe safe driving speeds especially on rough terrain Drinking and driving can be very dangerous on any road and this is certainly true for off road driving At the very time you need special alertness and driving skills your reflexes perceptions and judgment can be affected by even a small amount of alcohol You could have a serious or even fatal accident if you drink and drive or ride witha driver who has been drinking Off roading can be great fun but has some definite hazards The greatest of these is the terrain itself When off road driving traffic lanes are not marked curves are not banked and there are no road signs Surfaces can be slippery rough uphill or downhill Avoid sharp turns and abrupt maneuvers Failure to operate the vehicle correctly off road could result in loss of vehicle control or vehicle rollover Driving Your Vehicle 4 13 Off roading involves some new skills That is why it is very important that you read these driving tips and suggestions to help make off road driving safer and more enjoyable Before You Go Off Roading e Have all necessary maintenance and service work done e Make sure there is enough fuel that fluid levels are where they should be and that the spare tire is fully inflated e Be sure to read all the information abou
201. emoving the Spare Tire and Tools on page 5 65 to replace the floor and lock in place Place the flat or damaged tire face down on the bottom of the spare tire compartment After 5 Remove the disk A from the retainer bolt Turn the disk A over and place it back on the retainer bolt Return the disk back to its original position after removing the flat tire from the spare tire compartment and before storing the spare tire 6 Place the wheel retainer bolt onto the wheel stow rod and tighten by turning it clockwise The compact spare is for temporary use only Replace the compact spare tire with a full size tire as soon as possible Service and Appearance Care Compact Spare Tire Z CAUTION Driving with more than one compact spare tire at a time could result in loss of braking and handling This could lead to a crash and you or others could be injured Use only one compact spare tire at a time The compact spare tire was fully inflated when the vehicle was new however it can lose air after a time Check the inflation pressure regularly It should be 60 psi 414 kPa After installing the compact spare on your vehicle you should stop as soon as possible and make sure your spare tire is correctly inflated The compact spare is intended to perform well at speeds up to 50 mph 80 km h so you can finish your trip 5 71 and have your full size tire repaired or replace
202. enger airbag e Airbags are designed to inflate only once After an airbag inflates you will need some new parts for the airbag system If you do not get them the airbag system will not be there to help protect you in another crash A new system will include airbag modules and possibly other parts The service manual for your vehicle covers the need to replace other parts e The vehicle has a crash sensing and diagnostic module which records information after a crash See Vehicle Data Recording and Privacy on page 7 16 and Event Data Recorders on page 7 16 Seats and Restraint System e Let only qualified technicians work on the airbag systems Improper service can mean that an airbag system will not work properly See your dealer retailer for service Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started f PASSENGER AIRBAG OFF On a Be United States 1 51 He Be Canada The words ON and OFF or the symbol for on and off are visible during the system check If you are using remote start if equipped to start the vehicle from a distance you may not see the system check When the system check is complete either the word ON or OFF or the symbol for on or off will be visible See Passenger Airbag Status Indicator on pa
203. er allow a child to wear the safety belt with the shoulder belt behind their back A child can be seriously injured by not wearing the lap shoulder belt properly In a crash the child would not be restrained by the shoulder belt The child could move too far forward increasing the chance of head and neck injury The child might also slide under the lap belt The belt force would then be applied right on the abdomen That could cause serious or fatal injuries The shoulder belt should go over the shoulder and across the chest 1 25 1 26 Infants and Young Children Everyone in a vehicle needs protection This includes infants and all other children Neither the distance traveled nor the age and size of the traveler changes the need for everyone to use safety restraints In fact the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle Seats and Restraint System Z CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten Never leave children unattended in a vehicle and never allow children to play with the safety belts Airbags plus lap shoulder belts offer protection for adults and older children but not for young children and infants Neither the vehicle s safety belt system nor its airbag system is desig
204. ere may be a power outlet located inside the instrument panel storage area below the climate controls To use the outlets remove the cover When not in use always cover the outlet with the protective cap Notice Leaving electrical equipment on for extended periods will drain the battery Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses If you experience a problem see your dealer retailer for additional information on the accessory power outlet Notice Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should The repairs would not be covered by your warranty Check with your dealer retailer before adding electrical equipment When adding electrical equipment be sure to follow the installation instructions included with the equipment Notice Improper use of the power outlet can cause damage not covered by the warranty Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only Climate Controls Climate Control System The heating cooling and ventilation for the vehicle can be controlled with this system For vehicles with the remote start feature the c
205. ers on page 3 5 e Tie a red cloth to an outside mirror Driving Your Vehicle CAUTION Continued CAUTION Continued Z CAUTION Snow can trap engine exhaust under the vehicle This may cause exhaust gases to get inside Engine exhaust contains carbon monoxide CO which cannot be seen or smelled It can cause unconsciousness and even death Continued If the vehicle is stuck in the snow e Clear away snow from around the base of your vehicle especially any that is blocking the exhaust pipe e Check again from time to time to be sure snow does not collect there e Open a window about two inches 5 cm on the side of the vehicle that is away from the wind to bring in fresh air e Fully open the air outlets on or under the instrument panel e Adjust the Climate Control system to a setting that circulates the air inside the vehicle and set the fan speed to the highest setting See Climate Control System in the Index Continued For more information about carbon monoxide see Engine Exhaust on page 2 28 Snow can trap exhaust gases under your vehicle This can cause deadly CO carbon monoxide gas to get inside CO could overcome you and kill you You cannot see it or smell it so you might not know it is in your vehicle Clear away snow from around the base of your vehicle especially any that is blocking the exhaust Run the engine for short periods o
206. es or tunnels may cause loss of the XM signal for a period of time Cellular Phone Usage Cellular phone usage may cause interference with the vehicle s radio This interference may occur when making or receiving phone calls charging the phone s battery or simply having the phone on This interference causes an increased level of static while listening to the radio If static is received while listening to the radio unplug the cellular phone and turn it off Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged as long as it is securely attached to the base If the mast becomes slightly bent straighten it out by hand If the mast is badly bent replace it Occasionally check to make sure the antenna is tightened to its base If tightening is required tighten by hand Instrument Panel 3 93 XM Satellite Radio Antenna System The XM Satellite Radio antenna is located on the roof of the vehicle Keep the antenna clear of obstructions for clear radio reception If the vehicle has a sunroof the performance of the XM system may be affected if the sunroof is open Chime Level Adjustment The radio may be used to adjust the vehicle s chime level If the radio can be used to change the volume level of the chime press and hold the sixth FAV softkey with the ignition on and the radio power off The volume level changes between Normal and Loud The selected v
207. ess the OnStar button to confirm that the OnStar equipment is active Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand held Radio Frequency RF transmitters used to activate devices such as garage door openers security systems and home lighting This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Features and Controls This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment 2 37 Universal Home Remote System Operation QY If there is one triangular Light Emitting Diode LED indicator light above the Universal Home Remote buttons follow the instructions below This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers security systems and home automation devices 2 38 Do not use the Universal
208. essing the brake pedal The TCS StabiliTrak warning light will flash on the instrument panel cluster to notify the driver to reduce speed If the trailer continues to sway StabiliTrak will reduce engine torque to help slow the vehicle Adding non dealer non retailer accessories can affect the vehicle s performance See Accessories and Modifications on page 5 3 for more information Traction Control System TCS The vehicle has a Traction Control System TCS that limits wheel spin This is especially useful in slippery road conditions The system operates only if it senses that any of the drive wheels are spinning or beginning to lose traction When this happens TCS applies the brakes to limit wheel spin and also reduces engine power The system may be heard or felt while it is working but this is normal Bs OFF This light will flash when TCS is limiting wheel spin It is recommended to leave the system on for normal driving conditions but it may be necessary to turn the system off if the vehicle is stuck in sand mud ice or snow and you want to rock the vehicle to attempt to free it See Rocking Your Vehicle to Get It Out on page 4 27 and If Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 27 for more information N el The TCS StabiliTrak button is located on the instrument panel Press and release this button to turn off TCS The TCS warning light will be displayed on the
209. esult in engine damage not covered by the vehicle warranty Cold Temperature Operation If in an area of extreme cold where the temperature falls below 20 F 29 C use either an SAE 5W 30 synthetic oil or an SAE OW 30 engine oil Both provide easier cold starting for the engine at extremely low temperatures Always use an oil that meets the required specification GM6094M See What Kind of Engine Oil to Use for more information 5 16 Engine Oil Additives Engine Oil Flushes Do not add anything to the oil The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty Engine Oil Life System When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter This is based on engine revolutions and engine temperature and not on mileage Based on driving conditions the mileage at which an oil change is indicated can vary considerably For the oil life system to work properly the system must be reset every time the oil is changed Service and Appearance Care When the system has calculated that oil life has been diminished it indicates that an oil change is necessary A change engine oil light comes on See Change Engine Oil Light on page 3 38 Change t
210. et at zero and a label must be put on the driver s door to show the old mileage reading when the new odometer was installed If the mileage is unknown the label should then indicate that the previous mileage is unknown Trip Odometer The trip odometer can record the number of miles used in the United States or kilometers used in Canada traveled for up to two trips Cycle between the odometer and trip odometers A and B by pressing the reset button located in the lower right area of the speedometer Press the reset button to tell how many miles or kilometers have been recorded on either Trip A or Trip B since the trip odometer was last set back to zero To reset each trip odometer to zero press and hold the reset button The reset button resets only the trip odometer that is being displayed Each trip odometer must be reset individually Tachometer The tachometer displays the engine speed in revolutions per minute rpm Safety Belt Reminders Driver Safety Belt Reminder Light When the engine is started a chime sounds for several seconds to remind the driver to fasten their safety belt unless it is already buckled The safety belt light comes on and stays on for several seconds then flashes for several more This chime and light are repeated if the driver safety belt remains unbuckled and the vehicle is in motion If the driver safety belt is already buckled neither the chime nor the l
211. etailer for diagnosis If it is determined that the condition is caused by the type of fuel used repairs might not be covered by the vehicle warranty Additives To provide cleaner air all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming allowing the emission control system to work properly In most cases you should not have to add anything to the fuel However some gasolines contain only the minimum amount of additive required to meet U S Environmental Protection Agency regulations To help keep fuel injectors and intake valves clean or if the vehicle experiences problems due to dirty injectors or valves look for gasoline that is advertised as TOP TIER Detergent Gasoline For customers who do not use TOP TIER Detergent Gasoline regularly one bottle of GM Fuel System Treatment PLUS added to the fuel tank at every engine oil change can help clean deposits from fuel injectors and intake valves GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors Also your dealer retailer has additives that will help correct and prevent most deposit related problems Gasolines containing oxygenates such as ethers and ethanol and reformulated gasolines might be available in your area We recommend that you use these gasolines if they comply with the specifications described earlier Service and Ap
212. ever to P Park See Shifting Into Park Automatic Transmission on page 2 25 If you are pulling a trailer see Towing a Trailer on page 4 35 Make sure the shift lever is fully in P Park before starting the engine The vehicle has an automatic transmission shift lock control system 2 20 The regular brakes must be applied first and then the shift lever button pressed before you can shift from P Park when the ignition key is in ON RUN If you cannot shift out of P Park ease pressure on the shift lever and push the shift lever all the way into P Park as you maintain brake application Then press the shift lever button and move the shift lever into another gear See Shifting Out of Park on page 2 27 R Reverse Use this gear to back up Notice Shifting to R Reverse while the vehicle is moving forward could damage the transmission The repairs would not be covered by the vehicle warranty Shift to R Reverse only after the vehicle is stopped To rock the vehicle back and forth to get out of snow ice or sand without damaging the transmission see f Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 27 Features and Controls N Neutral In this position the engine does not connect with the wheels To restart the engine when the vehicle is already moving use N Neutral only Also use N Neutral when the vehicle is being towed Z CAUTION Shifting into a drive gear
213. evious set speed by a least 5 mph Reducing Speed While Using Cruise Control If the cruise control system is already engaged e Move the thumbwheel toward SET and hold until the desired lower speed is reached then release it To slow down in very small amounts move the thumbwheel toward SET briefly Each time this is done the vehicle goes about 1 mph 1 6 km h slower Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle s speed When you take your foot off the pedal the vehicle will slow down to the previously set cruise control speed Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle s speed load and the steepness of the hills When going up steep hills you might have to step on the accelerator pedal to maintain the vehicle s speed When going downhill you might have to brake or shift to a lower gear to maintain the vehicle s speed For some vehicles the transmission may automatically downshift when going down hills to help maintain the vehicle s speed When the brakes are applied the cruise control shuts off Instrument Panel 3 11 Ending Cruise Control There are three ways to disengage the cruise control e Step lightly on the brake pedal or clutch when cruise control disengages the indicator light on the instrument panel cluster goes out e Press to turn off the cruise co
214. ew Tires Buying New Tires Different Size Tires and Wheels Uniform Tire Quality Grading Wheel Alignment and Tire Balance Wheel Replacement Tire Chains If a Tire Goes Flat Changing a Flat Tire Removing the Spare Tire and Tools Removing the Flat Tire and Installing the Spare Tire Storing a Flat or Spare Tire and Tools Compact Spare Tire Service and Appearance Care Appearance Care Interior Cleaning Fabric Carpet Leather Instrument Panel Vinyl and Other Plastic Surfaces Care of Safety Belts Weatherstrips Washing Your Vehicle Cleaning Exterior Lamps Lenses Finish Care Windshield and Wiper Blades Aluminum Wheels Tires Sheet Metal Damage Finish Damage Underbody Maintenance Chemical Paint Spotting Vehicle Identification Vehicle Identification Number VIN Service Parts Identification Label Electrical System Add On Electrical Equipment Windshield Wiper Fuses Power Windows and Other Power Options Fuses and Circuit Breakers Instrument Panel Fuse Block Underhood Fuse Block Capacities and Specifications Capacities and Specifications Service For service and parts needs visit your dealer retailer You will receive genuine Saturn parts and Saturn trained and supported service people Genuine Saturn parts have one of these marks ACBelcoa l N SATURN e Service and Appearance Care Accessories and Modifications When non dealer non retailer accessories are added to the veh
215. f the vehicle it will have rails with adapters and hooks These are used to hold the net and mesh pocket The adapters are used to hold the net Slide the adapters to the desired location on the upper and lower rail and turn the handle up to lock it in place Compress the rods of the net and insert them into the corresponding openings of the adapter The longer rod is for the upper adapter The hooks hold the mesh pocket To insert a hook on the rail place the hook in the upper groove of the rail and press it into the lower groove Sunroof The sunroof switch is located between the sun visors To operate the sunroof the ignition must be in ON RUN ACC ACCESSORY or in Retained Accessory Power RAP See Retained Accessory Power RAP on page 2 17 Features and Controls Open Close Slide and release the switch rearward to express open the sunroof Slide the switch forward or rearward to stop movement The sun shade opens automatically with the sunroof or can be manually operated The sunshade cannot be closed with the sunroof open Slide and hold the switch forward to close the sunroof The sunshade must be closed manually Vent Open Close Press and hold the switch to vent the sunroof Pull and hold the switch to close it The sunshade must be manually operated when the sunroof is in the vent position 2 45 2 46 Features and Controls 4 NOTES Instrument Panel Instrument Panel Overview
216. f humidity and cool outside temperatures since this may result in increased window fogging If window fogging is experienced select the defrost mode Recirculation mode is not available in floor defog or defrost modes and will shut off automatically and change to outside air The indicator will flash if the button is selected in any of these modes This helps prevent window fogging and moisture building up inside the vehicle Instrument Panel 3 19 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window The rear window defogger only works when the ignition is in ON RUN G3 Rear Window Defogger Press to turn the rear window defogger on or off An indicator light on the button comes on to show that the rear window is activated The rear window defogger stays on for approximately 10 minutes after the button is pressed unless the ignition is turned to ACC ACCESSORY or LOCK OFF If turned on again the defogger only runs for approximately five minutes before turning off again At higher vehicle speeds the defogger may stay on continuously The defogger can also be turned off by turning off the engine 3 20 Instrument Panel For vehicles with the remote start feature the rear defogger will automatically turn on Notice Do not use anything sharp on the inside of the rear window If you do you could cut or damage the warming grid and the repairs would not
217. f injury from the force of an inflating bag all airbags must inflate very quickly to do their job Seats and Restraint System 1 43 Here are the most important things to know about the airbag system CAUTION Continued CAUTION Continued Z CAUTION You can be severely injured or killed in a crash if you are not wearing your safety belt even if you have airbags Airbags are designed to work with safety belts but do not replace them Also airbags are not designed to deploy in every crash In some crashes safety belts are your only restraint See When Should an Airbag Inflate on page 1 47 Continued Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it Airbags are supplemental restraints to the safety belts Everyone in your vehicle should wear a safety belt properly whether or not there is an airbag for that person Z CAUTION Airbags inflate with great force faster than the blink of an eye Anyone who is up against or very close to any airbag when it inflates can be seriously injured or killed Do not sit unnecessarily close to the airbag as you would Continued be if you were sitting on the edge of your seat or leaning forward Safety belts help keep you in position before and during a crash Always wear your safety belt even with airbags The driver should sit as far back
218. f you have a question ask for an explanation Reputable shops welcome this opportunity Customer Assistance Information Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs GM recommends that you take an active role in its repair If you have a pre determined repair facility of choice take your vehicle there or have it towed there Specify to the facility that any required replacement collision parts be original equipment parts either new Genuine GM parts or recycled original GM parts Remember recycled parts will not be covered by your GM vehicle warranty 7 13 Insurance pays the bill for the repair but you must live with the repair Depending on your policy limits your insurance company may initially value the repair using aftermarket parts Discuss this with your repair professional and insist on Genuine GM parts Remember if your vehicle is leased you may be obligated to have the vehicle repaired with Genuine GM parts even if your insurance coverage does not pay the full cost If another party s insurance company is paying for the repairs you are not obligated to accept a repair valuation based on that insurance company s collision policy repair limits as you have no contractual limits with that company In such cases you can have control of the repair and parts choices as long as cost stays within reasonable limits 7 14 Reporting Safety
219. ferent features Surface Conditions Off roading surfaces can be hard packed dirt gravel rocks grass sand mud snow or ice Each of these surfaces affects the vehicle s steering acceleration and braking in different ways Depending on the surface slipping sliding wheel spinning delayed acceleration poor traction and longer braking distances can occur Driving Your Vehicle Surface Obstacles Unseen or hidden obstacles can be hazardous A rock log hole rut or bump can startle you if you are not prepared for them Often these obstacles are hidden by grass bushes snow or even the rise and fall of the terrain itself Some things to consider e Is the path ahead clear e Will the surface texture change abruptly up ahead Does the travel take you uphill or downhill e Will you have to stop suddenly or change direction quickly When driving over obstacles or rough terrain keep a firm grip on the steering wheel Ruts troughs or other surface features can jerk the wheel out of your hands When driving over bumps rocks or other obstacles the wheels can leave the ground If this happens even with one or two wheels you cannot control the vehicle as well or at all Because you will be on an unpaved surface it is especially important to avoid sudden acceleration sudden turns or sudden braking Off roading requires a different kind of alertness from driving on paved roads and highwa
220. first so you know what the surface is like before driving it Stalling on an Incline Z CAUTION Getting out on the downhill low side of a vehicle stopped across an incline is dangerous If the vehicle rolls over you could be crushed or killed Always get out on the uphill high side of the vehicle and stay well clear of the rollover path If the vehicle stalls when crossing an incline be sure you and any passengers get out on the uphill side even if the door there is harder to open If you get out on the downhill side and the vehicle starts to roll over you will be right in its path If you have to walk down the slope stay out of the path the vehicle will take if it does roll over Driving in Mud Sand Snow or Ice When you drive in mud snow or sand the wheels do not get good traction Acceleration is not as quick turning is more difficult and braking distances are longer It is best to use a low gear when in mud the deeper the mud the lower the gear In really deep mud keep the vehicle moving so it does not get stuck When driving on sand wheel traction changes On loosely packed sand such as on beaches or sand dunes the tires will tend to sink into the sand This affects steering accelerating and braking Drive ata reduced speed and avoid sharp turns or abrupt maneuvers Driving Your Vehicle 4 21 Hard packed snow and ice offer the worst tire traction On
221. g the vehicle during a remote start and the engine is still running turn the key to the ON RUN position to drive the vehicle If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done If it is the vehicle s first remote start since it was last driven repeat these steps while the engine is still running to give a 10 minute time extension Remote start can be extended one time To manually shut off a remote start Aim the RKE transmitter at the vehicle and press Q until the parking lamps turn off e Turn on the hazard warning flashers e Turn the ignition switch on and then off The vehicle can be remote started two separate times between driving sequences The engine runs for 10 minutes after each remote start Or the engine run time can be extended another 10 minutes within the first 10 minute remote start time frame and before the engine stops For example if and then Q are pressed again after the vehicle has been running for five minutes 10 minutes are added allowing the engine to run for 15 minutes The additional 10 minutes are considered a second remote vehicle start The vehicle must be started with the key once two remote starts ora single remote start with one time extension has been done The vehicle can be started using the remote start feature again after the key is removed from the ignition The vehicle cannot be start
222. ge 3 30 1 52 The passenger sensing system turns off the right front passenger frontal airbag and seat mounted side impact airbag under certain conditions The driver airbags and the roof rail airbags are not affected by the passenger sensing system The passenger sensing system works with sensors that are part of the right front passenger seat and safety belt The sensors are designed to detect the presence of a properly seated occupant and determine if the right front passenger frontal airbag and seat mounted side impact airbag should be enabled may inflate or not Seats and Restraint System According to accident statistics children are safer when properly secured in a rear seat in a correct child restraint for their weight and size We recommend that children be secured in a rear seat including an infant or a child riding ina rear facing child restraint a child riding in a forward facing child seat an older child riding in a booster seat and children who are large enough using safety belts A label on the sun visor says Never put a rear facing child seat in the front This is because the risk to the rear facing child is so great if the airbag deploys Z CAUTION A child in a rear facing child restraint can be seriously injured or killed if the right front passenger airbag inflates This is because the back of the rear facing child restraint would be very close to the inflati
223. ghy Towing Front wheel drive and all wheel drive vehicles may be dinghy towed from the front These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground For other towing options see Dolly Towing following in this section For vehicles being dinghy towed the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes This will ensure proper lubrication of transmission components i i tf To tow the vehicle from the front with all four wheels on the ground 1 Position the vehicle that will be towed and secure it to the towing vehicle 2 Turn the ignition key to ACC ACCESSORY 3 Shift the transmission to N Neutral 4 Turn fog lamps and all accessories off 5 To prevent the battery from draining while the vehicle is being towed remove the 2 amp IGN SW fuse from the instrument panel fuse block and store itin a safe location See Instrument Panel Fuse Block on page 5 80 Notice lf the vehicle is towed without performing each of the steps listed under Dinghy Towing the automatic transmission could be damaged Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle Notice lf the vehicle has a four speed automatic transmission it can be dinghy towed from the front for unlimited miles at 65 mph 105 km h The vehicle could be damaged If
224. ginal key being turned to the LOCK OFF position The security light turns off once the key has been programmed 5 Repeat Steps 1 through 4 if additional keys are to be programmed If the PASS Key Ill key is lost or damaged see your dealer retailer or a locksmith to have a new key made Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle Starting and Operating Your Vehicle New Vehicle Break In Notice The vehicle does not need an elaborate break in But it will perform better in the long run if you follow these guidelines Do not drive at any one constant speed fast or slow for the first 500 miles 805 km Do not make full throttle starts Avoid downshifting to brake or slow the vehicle Features and Controls 2 15 Avoid making hard stops for the first 200 miles 322 km or so During this time the new brake linings are not yet broken in Hard stops with new linings can mean premature wear and earlier replacement Follow this breaking in guideline every time you get new brake linings Do not tow a trailer during break in See Towing a Trailer on page 4 35 for the trailer towing capabilities of your vehicle and more information Following break in engine speed and load can be gradually increased 2 16 Ignition Positions Hy 12 The ignition switch has four different positions To shift out of P Park turn the ignition to
225. gnition key to ACC ACCESSORY or ON RUN Press db to turn the radio on 2 Press and the HR MIN MM DD YYYY hour minute month day and year displays 3 Press the softkey located below any one of the tabs that you want to change 4 To increase the time or date do one of the following e Press the softkey located below the selected tab Press D1 SEEK or PD FWD e Turn J clockwise 5 To decrease the time or date do one of the following e Press KI SEEK or lt REV e Turn J counterclockwise The date does not automatically display To see the date press while the radio is on The date with display times out after a few seconds and goes back to the normal radio and time display Instrument Panel 3 65 To change the time default setting from 12 hour to 24 hour or to change the date default setting from month day year to day month year 1 Press and then the softkey located below the forward arrow label Once the time 12H and 24H and the date MM DD YYYY month day and year and DD MM YYYY day month and year displays 2 Press the softkey located below the desired option 3 Press again to apply the selected default or let the screen time out 3 66 Instrument Panel Six Disc CD MP3 Player To set the time and date 1 Turn the ignition key to ACC ACCESSORY or ON RUN Press b to turn the radio on 2 Press MENU 3 Press the softkey below the tab The HR MI
226. hance of circuit overload and fire caused by electrical problems There are two fuse blocks the underhood fuse block and the instrument panel fuse block To identify and check fuses and relays refer to the Fuse Usage Chart on the inside surface of the fuse panel door Instrument Panel Fuse Block The instrument panel fuse block is located on the passenger side of the lower console Pull the latch of the fuse box cover straight back to access the fuses PWR SEAT PASS Passenger Side P WIN Power Window DRIV Driver Side Power P WIN Window S ROOF Sunroof Module Service and Appearance Care CIGAR _ Cigarette Lighter Engine Control Module ECM Transmission Control Module TCM FSCM Je de Control ECM TCM 5 81 Inside Rearview ISRVM Mirror Instrument Panel CLUSTER Ca AIR BAG Airbag Airbag System iM lee Rearview par eo Wheel dew e E vB ten Module DRLCK Door Lock Body Control BOM VB6 Module VB6 5 82 Body Control BOM VB4 Module VB4 va eal Body Control BOM VB7 Module VB7 IGN SW Ignition Switch AIR BAG Air Bag System WASHER Washer Pump Accessory Power APO1 Outlet 1 Service and Appearance Care Fuel Storage Control TEA oe cate ONSTAR Relays Usage Accessory Retained oaa Accessory Power RAP Relay RELAY Run Crank Relay RUN CRANK Underhood Fuse Block The underhood fuse bl
227. he following Engine coolant will boil at a lower temperature than at normal altitudes If the engine is turned off immediately after towing at high altitude on steep uphill grades the vehicle may show signs similar to engine overheating To avoid this let the engine run while parked preferably on level ground with the automatic transmission in P Park for a few minutes before turning the engine off If the overheat warning comes on see Engine Overheating on page 5 25 Parking on Hills Z CAUTION Parking the vehicle on a hill with the trailer attached can be dangerous If something goes wrong the rig could start to move People can be injured and both the vehicle and the trailer can be damaged When possible always park the rig on a flat surface If parking the rig on a hill 1 Press the brake pedal but do not shift into P Park yet Turn the wheels into the curb if facing downhill or into traffic if facing uphill 2 Have someone place chocks under the trailer wheels 3 When the wheel chocks are in place release the regular brakes until the chocks absorb the load 4 Reapply the brake pedal Then apply the parking brake and shift into P Park 5 Release the brake pedal Leaving After Parking on a Hill 1 Apply and hold the brake pedal while you e Start the engine e Shift into a gear e Release the parking brake 2 Let up on the brake pedal 3 Drive slowly until t
228. he hand held transmitter Release both buttons 5 Press and hold the newly trained Universal Home Remote button and observe the indicator light If the indicator light stays on continuously the programming is complete and the garage door should move when the Universal Home Remote button is pressed and released There is no need to continue programming Steps 6 through 8 If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light continue with the programming Steps 6 through 8 2 39 It may be helpful to have another person assist with the remaining steps am eee a i E li 6 After Steps 1 through 5 have been completed locate inside the garage the garage door opener receiver motor head unit Locate the Learn or Smart button The name and color of the button may vary by manufacturer 2 40 7 Firmly press and release the Learn or Smart button After you press this button you will have 30 seconds to complete Step 8 8 Immediately return to the vehicle Firmly press and hold the Universal Home Remote button chosen in Step 3 to control the garage door for two seconds and then release it If the garage door does not move press and hold the same button a second time for two seconds and then release it Again if the door does not move press and hold the same button a third time for two seconds and then
229. he tune knob until the speaker control labels display Continue pressing to highlight the desired tab or press the pushbutton positioned under the desired label Turn the Jd knob clockwise or counterclockwise to adjust the highlighted setting The highlighted setting can also be adjusted is ressing d SEEK arrow FWD or REV until the desired levels are obtained To quickly adjust balance or fade to the middle position press the pushbutton positioned under the BAL or FADE label for more than two seconds A beep sounds and the level adjusts to the middle position To quickly adjust all speaker and tone controls to the middle position press the dd knob for more than two seconds until a beep sounds 3 70 Instrument Panel Finding a Category CAT Station CAT Category The CAT button is used to find XM stations when the radio is in the XM mode To find XM channels within a desired category perform the following 1 Press the BAND button until the XM frequency displays Press the CAT button to display the category tabs on the radio display Continue pressing the CAT button until the desired category name displays 2 Press either of the two buttons below the desired category tab to immediately tune to the first XM station associated with that category 3 Turn the Jd knob press the buttons below the right or left arrows displayed or press either SEEK arrow to go to the previous or to the next XM station with
230. he Dial Command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Dial The system responds with Dial using lt phone name gt Number please followed by a tone 3 Say the entire number without pausing e If the system recognizes the number it responds with OK Dialing and dials the number e Ifthe system does not recognize the number it confirms the numbers followed by atone If the number is correct say Yes The system responds with OK Dialing and dials the number If the number is not correct say No The system will ask for the number to be re entered Using the Digit Dial Command 1 Press and hold 9 for two seconds The system responds with Ready followed by a tone 2 Say Digit Dial The system responds with Digit dial using lt phone name gt please say the first digit to dial followed by atone 3 Say the digits to be dialed one at a time Following each digit the system will repeat back the digit it heard followed by a tone 4 Continue entering digits until the number to be dialed is complete After the whole number has been entered say Dial The system responds with OK Dialing and dials the number e If an unwanted number is recognized by the system say Clear at any time to clear the last number To hear all of the numbers recognized by the system
231. he Engine Running Automatic Transmission Z CAUTION It can be dangerous to leave the vehicle with the engine running The vehicle could move suddenly if the shift lever is not fully in P Park with the parking brake firmly set And if you leave the vehicle with the engine running it You or others could be injured Do not leave the vehicle with the engine running could overheat and even catch fire Features and Controls If you have to leave an automatic transmission vehicle with the engine running be sure the vehicle is in P Park and the parking brake is firmly set before you leave it After you have moved the shift lever into P Park hold the brake pedal down Then see if you can move the shift lever away from P Park without first pushing the button If you can it means that the shift lever was not fully locked into P Park Torque Lock Automatic Transmission If you are parking on a hill and you do not shift into P Park properly the weight of the vehicle may put too much force on the parking pawl in the transmission You may find it difficult to pull the shift lever out of P Park This is called torque lock To prevent torque lock set the parking brake and then shift into P Park properly before you leave the driver seat To find out how see Shifting Into Park Automatic Transmission on page 2 25 Move the shift lever out of P Park before you release the
232. he GVWR for your vehicle or the GAWR for either the front or rear axle Driving Your Vehicle 4 31 Z CAUTION Z CAUTION Do not load the vehicle any heavier than the Gross Vehicle Weight Rating GVWR or either the maximum front or rear Gross Axle Weight Rating GAWR If you do parts on the vehicle can break and it can change the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of the vehicle Notice Overloading your vehicle may cause damage Repairs would not be covered by your warranty Do not overload your vehicle If you put things inside your vehicle like suitcases tools packages or anything else they will go as fast as the vehicle goes If you have to stop or turn quickly or if there is a crash they will keep going Things you put inside your vehicle can strike and injure people in a sudden stop or turn or in a crash e Put things in the cargo area of your vehicle Try to spread the weight evenly e Never stack heavier things like suitcases inside the vehicle so that some of them are above the tops of the seats e Do not leave an unsecured child restraint in your vehicle When you carry something inside the vehicle secure it whenever you can Do not leave a seat folded down unless you need to 4 32 Towing Towing Your Vehicle To avoid damage the disabled vehicle should be towed w
233. he alarm by accident turn off the alarm by pressing or on the RKE transmitter or by placing the key in the ignition and turning it to START Testing the Alarm To test the alarm 1 From inside the vehicle lower the driver window and open the driver door 2 Get out of the vehicle close the door and activate the system by locking the doors with the RKE transmitter 3 Wait for the security light to flash slowly 4 Then reach in through the window unlock the door with the manual door lock and open the door This should set off the alarm If the alarm does not sound when it should but the vehicle s headlamps flash check to see if the horn works The horn fuse may be blown To replace the fuse see Fuses and Circuit Breakers on page 5 80 If the alarm does not sound or the vehicle s headlamps do not flash see your dealer retailer for service Features and Controls PASS Key Ill Electronic Immobilizer The PASS Key lll system operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation 2 13 This device complies with RSS 210 of Industry Canada Operation is subje
234. he oil as soon as possible within the next 600 miles 1 000 km It is possible that if driving under the best conditions the oil life system might not indicate that an oil change is necessary for over a year However the engine oil and filter must be changed at least once a year and at this time the system must be reset Your dealer retailer has trained service people who will perform this work using genuine parts and reset the system It is also important to check the oil regularly and keep it at the proper level If the system is ever reset accidentally the oil must be changed at 3 000 miles 5 000 km since the last oil change Remember to reset the oil life system whenever the oil is changed How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use Whenever the oil is changed reset the system so it can calculate when the next oil change is required If a situation occurs where the oil is changed prior to a change engine oil light being turned on reset the system After changing the engine oil reset the system 1 Turn the ignition key to ON RUN with the engine off 2 Fully press and release the accelerator pedal three times within five seconds If the change engine oil light is not on the system is reset If the light comes on again and stays on for 30 seconds at the next ignition cycle it did not reset The syst
235. he owner of the vehicle registers with OnStar After the first prepaid year contact OnStar to select a monthly or annual subscription payment plan If a payment plan is not selected the OnStar system and all services including airbag notification and emergency services may be deactivated and no longer available For more information visit onstar com U S or onstar ca Canada or press the OnStar button to speak with an advisor Features and Controls Not all OnStar services are available on all vehicles To check if this vehicle is able to provide the services described below or for a full description of OnStar services and system limitations see the OnStar Owner s Guide in the glove box or visit onstar com U S or onstar ca Canada contact OnStar at 1 888 4 ONSTAR 1 888 466 7827 or TTY 1 877 248 2080 or press the OnStar button to speak with an OnStar advisor 24 hours a day 7 days a week OnStar Services Available with the Safe amp Sound Plan e Automatic Notification of Airbag Deployment e Advanced Automatic Crash Notification AACN If equipped e Link to Emergency Services e Roadside Assistance e Stolen Vehicle Location Assistance e Remote Door Unlock Vehicle Alert e OnStar Vehicle Diagnostic Email e GM Goodwrench On Demand Diagnostics e OnStar Hands Free Calling with 30 trial minutes e OnStar Virtual Advisor U S Only OnStar Services Included with Directions amp Connect
236. he tire s sidewall To decrease the tire s air pressure use the pointed end of the valve cap a pencil style air pressure gage or a key You have two minutes to match each tire and wheel position If it takes longer than two minutes to match any tire and wheel position the matching process stops and you will need to start over The TPMS matching process is outlined below 1 2 3 Set the parking brake Turn the ignition switch to ON RUN with the engine off Press and hold the RKE transmitter s Lock and Unlock buttons at the same time for about three seconds The horn will sound twice to indicate the receiver is ready for the sensor matching process to begin Service and Appearance Care Start with the driver side front tire The driver side turn signal lamp comes on Remove the valve cap from the tire s valve stem Activate the TPMS sensor by increasing or decreasing the tire s air pressure for five seconds or until a horn chirp sounds The horn chirp which may take up to 30 seconds to sound confirms that the sensor identification code has been matched to the tire wheel position Proceed to the passenger side front tire The passenger side front turn signal lamp comes on Repeat the procedure in Step 5 Proceed to the passenger side rear tire The passenger side rear turn signal lamp comes on Repeat the procedure in Step 5 8 9 5 55 Proceed to the
237. he trailer is clear of the chocks 4 Stop and have someone pick up and store the chocks Driving Your Vehicle 4 43 Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer See Scheduled Maintenance on page 6 3 for more information Things that are especially important in trailer operation are automatic transmission fluid engine oil axle lubricant belts cooling system and brake system It is a good idea to inspect these before and during the trip Check periodically to see that all hitch nuts and bolts are tight Engine Cooling When Trailer Towing The cooling system may temporarily overheat during severe operating conditions See Engine Overheating on page 5 25 4 44 Driving Your Vehicle 4 NOTES Service and Appearance Care Service Semvice s lt seecies seseesisveasiasaseeces 5 3 Accessories and Modifications s seseeeeeee 5 3 California Proposition 65 Warning seeen reinate is 5 4 California Perchlorate Materials Requirements 5 4 Doing Your Own Service Work scsceceseeeeeeees 5 4 Adding Equipment to the Outside of the Vehicle 5 5 Fuel Fuel sciuciee de teckicecctacendiectancdiacs 5 5 Gasoline Octane eeeeee es 5 5 Gasoline Specifications 5 6 California Fuel sceceeceeeees 5 6 Additives c casse0esssaeeecseneeoee 5 6 Fuels in Foreign Countries 5 8 Filling the Tank c 00c
238. hever occurs first An Emission Control Service See footnote i Inspect engine accessory drive belt An Emission Control Service See footnote n 6 8 Maintenance Footnotes t The U S Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle s useful life We however urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded a Visually inspect brake lines and hoses for proper hook up binding leaks cracks chafing etc Inspect disc brake pads for wear and rotors for surface condition Inspect other brake parts including calipers parking brake etc b Visually inspect front and rear suspension and steering system for damaged loose or missing parts or signs of wear Maintenance Schedule c Visually inspect hoses and have them replaced if they are cracked swollen or deteriorated Inspect all pipes fittings and clamps replace with genuine parts as needed To help ensure proper operation a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year d Inspect wiper blades for wear cracking or contamination Clean the windshield and wiper bl
239. high speed heated seats engine cooling fans trailer loads and loads plugged into accessory power outlets EPM works to prevent excessive discharge of the battery It does this by balancing the generator s output and the vehicle s electrical needs Instrument Panel 3 15 It can increase engine idle speed to generate more power whenever needed It can temporarily reduce the power demands of some accessories Normally these actions occur in steps or levels without being noticeable In rare cases at the highest levels of corrective action this action may be noticeable to the driver If so a Driver Information Center DIC message might be displayed such as BATTERY SAVER ACTIVE BATTERY VOLTAGE LOW or LOW BATTERY If this message is displayed it is recommended that the driver reduce the electrical loads as much as possible See DIC Warnings and Messages on page 3 49 3 16 Instrument Panel Battery Run Down Protection The battery saver feature is designed to protect the vehicle s battery If any interior or exterior lamp is left on and the ignition is turned off the battery rundown protection system automatically turns the lamp off after 10 minutes Accessory Power Outlet s The accessory power outlets can be used to connect electrical equipment such as a cellular phone The accessory power outlets are located on the rear of the center storage console and in the rear cargo compartment Th
240. ht even be noticed that the brake pedal moves a little This is normal If there is a problem with ABS this warning light stays on See Antilock Brake System ABS Warning Light on page 3 32 Let us say the road is wet and you are driving safely Suddenly an animal jumps out in front of you You slam on the brakes and continue braking Here is what happens with ABS A computer senses that the wheels are slowing down If one of the wheels is about to stop rolling the computer will separately work the brakes at each wheel ABS can change the brake pressure to each wheel as required faster than any driver could This can help the driver steer around the obstacle while braking hard As the brakes are applied the computer keeps receiving updates on wheel speed and controls braking pressure accordingly Remember ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance If you get too close to the vehicle in front of you there will not be enough time to apply the brakes if that vehicle suddenly slows or stops Always leave enough room up ahead to stop even with ABS Using ABS Do not pump the brakes Just hold the brake pedal down firmly and let antilock work The antilock pump or motor operating might be heard and the brake pedal might be felt to pulsate but this is normal Braking in Emergencies ABS allows the driver to steer and brake
241. ible to steal Content Theft Deterrent Your vehicle may have a content theft deterrent alarm system Ore s EN Ta United States shown Canada similar The security light is located near the center of the instrument panel Features and Controls To arm the theft deterrent system press on the RKE transmitter when all doors and the hood vehicles started with the remote start feature only are closed The security light will come on solid for approximately 30 seconds and then flashes slowly If on the RKE transmitter is pressed a second time the theft deterrent system will activate immediately bypassing the 30 second delay The content theft deterrent alarm is not armed until the security light flashes slowly If any door liftgate or the hood vehicles started with the remote start feature only are opened without using the key or pressing on the RKE transmitter the exterior lamps flash and the horn will sound for about 30 seconds If or on the RKE transmitter is not pressed the alarm sounds and periodically repeats If the system does not operate as described above see your dealer retailer for service The theft deterrent system also activates if you lock the doors with a key To avoid setting off the alarm by accident always unlock a door with the RKE transmitter or a key Unlocking a door any other way will set off the alarm if the system has been armed If you set off t
242. ication RFID Proposition 65 Warning California Radio Frequency Identification RFID PRIVACY iiser messini renee Radio s Radios Navigation Radio System see Navigation Manual Reception Setting the Clock Theft Deterrent Rainsense Wipers Reading Lamps Rear Door Security Locks Rear Seat Armrest Rear Vision Camera RVC Rear Window Washer Wiper Rearview Mirror Automatic DIMMING sasian 2 29 Rearview Mirrors 065 2 29 Reclining Seatbacks 1 6 Recommended Fluids and Lubricants 0ceeeeee 6 13 Recreational Vehicle Towing Reduced Engine Power LIGNE ienirt asra 3 39 Reimbursement Program GM Mobility 7 6 Remote Keyless Entry RKE SYSIOM sereen scons 2 3 Remote Keyless Entry RKE System Operation 2 4 Remote Vehicle Start 2 5 Removing the Flat Tire and Installing the Spare Tire 5 66 Removing the Spare Tire and Tools serisini 5 65 Replacement Bulbs 5 41 Replacement Parts Maintenance 65 6 15 Reporting Safety Defects Canadian Government 7 14 Reporting Safety Defects to Saturn aroo eee es 7 14 Reporting Safety Defects to the Canadian Government 066 Restraint System Check Checking the Restraint SySteMS enana Replacing Restraint System Parts After a Crash Retained Accessory Power RAP oen Roadside Assistance Pr graM niciaietci
243. icle they can affect vehicle performance and safety including such things as airbags braking stability ride and handling emissions systems aerodynamics durability and electronic systems like antilock brakes traction control and stability control Some of these accessories could even cause malfunction or damage not covered by the vehicle warranty Damage to vehicle components resulting from the installation or use of non GM certified parts including control module modifications are not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts 5 3 GM Accessories are designed to complement and function with other systems on the vehicle Your GM dealer retailer can accessorize the vehicle using genuine GM Accessories When you go to your GM dealer retailer and ask for GM Accessories you will know that GM trained and supported service technicians will perform the work using genuine GM Accessories Also see Adding Equipment to Your Airbag Equipped Vehicle on page 1 57 5 4 Service and Appearance Care California Proposition 65 Warning Most motor vehicles including this one contain and or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Engine exhaust many parts and systems including some inside the vehicle many fluids and some component wear by products contain and or emit these chemi
244. ight also appears on the instrument panel cluster See StabiliTrak Indicator Light on page 3 33 See StabiliTrak System on page 4 7 for more information If this message turns on while you are driving pull off the road as soon as possible and stop carefully Try resetting the system by turning the ignition off and then back on If this message still stays on or turns back on again while you are driving your vehicle needs service Have the system inspected by your dealer retailer as soon as possible SERVICE TIRE MONITORING SYSTEM On vehicles with the Tire Pressure Monitor System TPMS this message displays if a part on the TPMS is not working properly The tire pressure light also flashes and then remains on during the same ignition cycle See Tire Pressure Light on page 3 34 Several conditions may cause this message to appear See Tire Pressure Monitor Operation on page 5 53 for more information If the warning comes on and stays on there may be a problem with the TPMS See your dealer retailer SERVICE TRACTION CONTROL This message displays when the Traction Control System TCS is not functioning properly A warning light also appears on the instrument panel cluster See Traction Control System TCS Warning Light on page 3 33 and Traction Control System TCS on page 4 8 for more information Have the TCS serviced by your dealer retailer as soon as possible SERVICE TRANSMISSION This message disp
245. ight comes on Passenger Safety Belt Reminder Light Several seconds after the engine is started a chime sounds for several seconds to remind the front passenger to buckle their safety belt This only occurs if the passenger airbag is enabled See Passenger Sensing System on page 1 517 for more information The passenger safety belt light located on the instrument panel comes on and stays on for several seconds and then flashes for several more Be This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion If the passenger safety belt is buckled before the engine is started neither the chime nor the light comes on The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase handbag grocery bag laptop or other electronic device To turn off the warning light and or chime remove the object from the seat or buckle the safety belt Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster which shows the airbag symbol The system checks the airbag s electrical system for malfunctions The light indicates if there is an electrical problem The system check includes the airbag sensor the pretensioners the airbag modules the wiring and the crash sensing and diagnostic module For more information on the airbag system see Airbag System on page 1 42 Instrument Panel 3 29
246. ignaling a turn or lane change the arrow flashes rapidly or does not come on a signal bulb may be burned out Have the bulbs replaced If a bulb is not burned out check the fuse See Fuses and Circuit Breakers on page 5 80 and for burned out bulbs Headlamp High Low Beam Changer 2D D Headlamp High Low Beam Changer Push the turn signal multifunction lever away from you to turn the high beams on Pull the lever towards you to return to low beams This indicator light turns on in the instrument panel cluster when the high beam headlamps are on Flash to Pass This feature lets you use your high beam headlamps to signal a driver in front of you that you want to pass To flash the high beams from low beam pull the turn signal multifunction lever all the way towards you Then release it Windshield Wipers The windshield wiper lever is located on the right side of the steering column Instrument Panel 3 7 Push up or pull down on the lever to place it in one of the following positions Wy Mist For a single wiping cycle The lever returns to its starting position when released For more cycles hold the lever down before releasing it O Off Turns the wipers off SY Intermittent Sets a delay between wipes To set for a shorter or longer delay between wipes move the switch on top of the lever left or right to decrease or increase wiper movement Low For slow steady wiping
247. in the selected category 4 To exit the category search mode press the FAV button or BAND button to display favorites again Undesired XM categories can be removed through the setup menu To remove an undesired category 1 Press the MENU button to display the radio setup menu 2 Press the pushbutton located below the XM CAT tab 3 Turn the JJ knob to display the category to be removed 4 Press the pushbutton located under the Remove tab until the category name along with the word Removed displays 5 Repeat the steps to remove more categories Removed categories can be restored by pressing the pushbutton under the Add tab when a removed category is displayed or by pressing the pushbutton under the Restore All tab The radio does not allow categories to be removed or added while the vehicle is moving faster than 5 mph 8 km h XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces XM Satellite Radio has a wide variety of programming and commercial free music coast to coast and in digital quality sound During your trial or when you subscribe you will get unlimited access to XM Radio Online for when you are not in the vehicle A service fee is required to receive the XM service For more information contact XM at xmradio com or call 1 800 929 2100 in the U S and xmradio ca or call 1 877 438 9677 in Canada
248. in the player it stays in the player When the ignition or radio is turned on the CD starts playing where it stopped if it was the last selected audio source When a CD is inserted the CD symbol displays on the CD As each new track starts to play the track number displays The CD player can play the smaller 3 inch 8 cm single CDs with an adapter ring Full size CDs and the smaller CDs are loaded in the same manner 3 72 Instrument Panel Care of CDs If playing a CD R the sound quality can be reduced due to CD R quality the method of recording the quality of the music that has been recorded and the way the CD R has been handled Handle them carefully Store CD R s in their original cases or other protective cases and away from direct sunlight and dust The CD player scans the bottom surface of the disc If the surface of a CD is damaged such as cracked broken or scratched the CD does not play properly or not at all Do not touch the bottom side of a CD while handling it this could damage the surface Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge If the surface of a CD is soiled take a soft lint free cloth or dampen a clean soft cloth in a mild neutral detergent solution mixed with water and clean it Make sure the wiping process starts from the center to the edge Care of the CD Player Do not add any label to a CD it could get caught in the CD player
249. ind of lubricant to use See Recommended Fluids and Lubricants on page 6 13 Carrier Assembly Differential Rear Drive Module When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it See Scheduled Maintenance on page 6 3 5 36 How to Check Lubricant z eee a a p k i A B AWD Differential Case A Fill Plug B Drain Plug To get an accurate reading the vehicle should be on a level surface Service and Appearance Care If the level is below the bottom of the filler plug hole you ll need to add some lubricant Add enough lubricant to raise the level to the bottom of the filler plug hole A fluid loss could indicate a problem check and have it repaired if needed What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use See Recommended Fluids and Lubricants on page 6 13 Headlamp Aiming The headlamp aiming system has been preset at the factory If the vehicle is damaged in an accident the aim of the headlamps may be affected and adjustment may be necessary It is recommended that a dealer retailer adjust the headlamps To re aim the headlamps yourself use the following procedure The vehicle should be properly prepared as follows e The vehicle should be placed so the headlamps are 25 ft 7 6 m from a light colored wall e The vehicle must have al
250. information Remote Keyless Entry RKE System If this vehicle has the Remote Keyless Entry RKE system it operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Features and Controls 2 3 If there is a decrease in the RKE operating range try this e Check the distance The transmitter may be too far from the vehicle Stand closer during rainy or snowy weather e Check the location Other vehicles or objects may be blocking the signal Take a few steps to the left or right hold the transmitter higher and try again e Check the transmitter s battery See Battery Replacement later in this section e If the transmitter is still not working correctly
251. ins only folders subfolders and no compressed files directly beneath them the player advances to the next folder in the file structure that contains compressed audio files The empty folder does not display No Folder When the CD contains only compressed files the files are located under the root folder The next and previous folder functions do not display on a CD that was recorded without folders or playlists When displaying the name of the folder the radio displays ROOT When the CD contains only playlists and compressed audio files but no folders all files are located under the root folder The folder down and up buttons searches playlists Px first and then go to the root folder When the radio displays the name of the folder the radio displays ROOT Order of Play Tracks recorded to the CD R or CD RW are played in the following order e Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist When the last track of the last playlist has played play continues from the first track of the first playlist e Play begins from the first track in the first folder and continues sequentially through all tracks in each folder When the last track of the last folder has been played play continues from the first track of the first folder When play enters a new folder the display does not automatically show the new folder name unless the folder
252. ions Plan e All Safe and Sound Plan Services e OnStar Turn by Turn Navigation If equipped or Driving Directions Advisor delivered e RideAssist Information and Convenience Services OnStar Hands Free Calling OnStar Hands Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands Hands Free Calling is fully integrated into the vehicle and can be used with OnStar Pre Paid Minute Packages Most vehicles include 30 trial minutes good for 60 days Hands Free Calling can also be linked to a Verizon Wireless service plan in the U S or a Bell Mobility service plan in Canada depending on eligibility To find out more refer to the OnStar Owner s Guide in the vehicle s glove box visit onstar com or onstar ca or speak with an OnStar advisor by pressing the OnStar button or calling 1 888 4 ONSTAR 1 888 466 7827 OnStar Turn by Turn Navigation Vehicles with the OnStar Turn by Turn Navigation system can provide voice guided driving directions Press the OnStar button to have an OnStar advisor locate a business or address and download driving directions to the vehicle Voice guided directions to the desired destination will play through the audio system speakers See the OnStar Owner s Guide for more information Features and Controls 2 35 OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands Free Calling that uses minutes to access
253. ire pressure readings for vehicles with the Tire Pressure Monitor System TPMS Remote Keyless Entry RKE transmitter programming compass zone setting compass recalibration on vehicles with this feature coolant temperature and battery voltage amp Customization Press this button to customize the feature settings on your vehicle See DIC Vehicle Customization on page 3 57 for more information V Set Reset Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC Trip Fuel Menu Items ZN Trip Fuel Press this button to scroll through the following menu items Odometer Press the trip fuel button until ODOMETER displays This display shows the distance the vehicle has been driven in either miles mi or kilometers km Pressing the trip odometer reset stem will also display the odometer To switch between English and metric measurements see Units later in this section 3 44 Instrument Panel Trip Odometer Press the trip fuel button until TRIP A or TRIP B displays This display shows the current distance traveled in either miles mi or kilometers km since the last reset for the trip odometer Pressing the trip odometer reset stem will also display the trip odometer Each trip odometer can be reset to zero separately by pressing the set reset button while the trip odometer is displayed You can also reset the trip odometer while itis d
254. ires may look properly inflated even when they are under inflated Check the tire s inflation pressure when the tires are cold Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile 1 6 km Service and Appearance Care Remove the valve cap from the tire valve stem Press the tire gage firmly onto the valve to get a pressure measurement If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label no further adjustment is necessary If the inflation pressure is low add air until you reach the recommended amount If you overfill the tire release air by pushing on the metal stem in the center of the tire valve Re check the tire pressure with the tire gage Be sure to put the valve caps back on the valve stems They help prevent leaks by keeping out dirt and moisture High Speed Operation Z CAUTION Driving at high speeds 100 mph 160 km h or higher puts an additional strain on tires Sustained high speed driving causes excessive heat build up and can cause sudden tire failure You could have a crash and you or others could be killed Some high speed rated tires require inflation pressure adjustment for high speed operation When speed limits and road conditions are such that a vehicle can be driven at high speeds make sure the tires are rated for high speed operation in excellent condition and set to the
255. is in ON RUN the brake system warning light will come on To release the parking brake hold the brake pedal down Pull the parking brake lever up until you can press the release button Hold the release button in as you move the brake lever all the way down Release the parking brake before driving the vehicle Notice Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts Make sure that the parking brake is fully released and the brake warning light is off before driving Shifting Into Park Features and Controls 2 25 To shift into P Park Automatic Transmission 1 Hold the brake pedal down and set the parking brake Z CAUTION See Parking Brake on page 2 24 for more information It can be dangerous to get out of the vehicle if the shift lever is not fully in P Park with the parking brake firmly set The vehicle can roll If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure the vehicle will not move even when you are on fairly level ground use the steps that follow If you are pulling a trailer see Towing a Trailer on page 4 35 2 Move the shift lever into P Park by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle 3 Turn the ignition key to LOCK OFF 2 26 Leaving the Vehicle With t
256. is opened the lights remain on and stay on for 20 seconds after the doors are closed or until the key is put into the ignition and turned to the ACC ACCESSORY position The lights will then gradually dim until they are no longer lit Reading Lamps The reading lamps are located on the overhead console To turn the reading lamps on or off press the button located next to each lamp Electric Power Management The vehicle has Electric Power Management EPM that estimates the battery s temperature and state of charge It then adjusts the voltage for best performance and extended life of the battery When the battery s state of charge is low the voltage is raised slightly to quickly bring the charge back up When the state of charge is high the voltage is lowered slightly to prevent overcharging If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center DIC you may see the voltage move up or down This is normal If there is a problem an alert will be displayed The battery can be discharged at idle if the electrical loads are very high This is true for all vehicles This is because the generator alternator may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads A high electrical load occurs when several of the following are on such as headlamps high beams fog lamps rear window defogger climate control fan at
257. isplayed by pressing and holding the trip odometer reset stem Fuel Range Press the trip fuel button until FUEL RANGE displays This display shows the approximate number of remaining miles mi or kilometers km the vehicle can be driven without refueling The display will show LOW if the fuel level is low The fuel range estimate is based on an average of the vehicle s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank This estimate will change if driving conditions change For example if driving in traffic and making frequent stops this display may read one number but if the vehicle is driven on a freeway the number may change even though the same amount of fuel is in the fuel tank This is because different driving conditions produce different fuel economies Generally freeway driving produces better fuel economy than city driving Fuel range cannot be reset If the vehicle is low on fuel the FUEL LEVEL LOW message will be displayed See FUEL LEVEL LOW under DIC Warnings and Messages on page 3 49 Average Fuel Economy Press the trip fuel button until AVERAGE FUEL ECONOMY displays This display shows the approximate average miles per gallon mpg or liters per 100 kilometers L 100 km This number is calculated based on the number of mpg L 100 km recorded since the last time this menu item was reset To reset the AVERAGE FUEL ECONOMY press and ho
258. ith all four wheels off the ground Consult your dealer retailer or a professional towing service if the disabled vehicle must be towed See Roadside Assistance Program on page 7 6 To tow the vehicle behind another vehicle for recreational purposes such as behind a motorhome see Recreational Vehicle Towing following Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle such as behind a motorhome The two most common types of recreational vehicle towing are known as dinghy towing and Driving Your Vehicle dolly towing Dinghy towing is towing the vehicle with all four wheels on the ground Dolly towing is towing the vehicle with two wheels on the ground and two wheels up ona device known as a dolly Here are some important things to consider before recreational vehicle towing e What is the towing capacity of the towing vehicle Be sure to read the tow vehicle manufacturer s recommendations e What is the distance that will be travelled Some vehicles have restrictions on how far and how long they can tow Is the proper towing equipment going to be used See your dealer retailer or trailering professional for additional advice and equipment recommendations e Is the vehicle ready to be towed Just as preparing the vehicle for a long trip make sure the vehicle is prepared to be towed See Before Leaving on a Long Trip on page 4 24 Din
259. ity Weight for Example 2 1 000 lbs 453 kg B Subtract Occupant Weight 150 Ibs 68 kg x 5 750 Ibs 340 kg C Available Cargo Weight 250 Ibs 113 kg Driving Your Vehicle Example 3 A Vehicle Capacity Weight for Example 3 1 000 lbs 453 kg B Subtract Occupant Weight 200 Ibs 91 kg x 5 1 000 Ibs 453 kg C Available Cargo Weight 0 Ibs 0 kg Refer to your vehicle s tire and loading information label for specific information about your vehicle s capacity weight and seating positions The combined weight of the driver passengers and cargo should never exceed your vehicle s capacity weight Certification Tire Label Label Example A vehicle specific Certification Tire label is attached to the lower area of the center pillar B Pillar The label shows the gross weight capacity of your vehicle This is called the Gross Vehicle Weight Rating GVWR The GVWR includes the weight of the vehicle all occupants fuel cargo and trailer tongue weight if the vehicle is pulling a trailer The Certification Tire label also tells you the maximum weights for the front and rear axles called the Gross Axle Weight Rating GAWR To find out the actual loads on your front and rear axles you need to go to a weigh station and weigh your vehicle Your dealer retailer can help you with this Be sure to spread out your load equally on both sides of the centerline Never exceed t
260. ive extended attention to entertainment tasks while driving This system provides access to many audio and non audio listings To minimize taking your eyes off the road while driving do the following while the vehicle is parked e Become familiar with the operation and controls of the audio system e Set up the tone speaker adjustments and preset radio stations For more information see Defensive Driving on page 4 3 Notice Contact your dealer retailer before adding any equipment Adding audio or communication equipment could interfere with the operation of the vehicle s engine radio or other systems and could damage them Follow federal rules covering mobile radio and telephone equipment Notice The chime signals related to safety belts parking brake and other functions of your vehicle operate through the radio entertainment system If that equipment is replaced or additional equipment is added to your vehicle the chimes may not work Make sure that replacement or additional equipment is compatible with your vehicle before installing it See Accessories and Modifications on page 5 3 The vehicle has Retained Accessory Power RAP With RAP the audio system can be played even after the ignition is turned off See Retained Accessory Power RAP on page 2 17 for more information Setting the Clock Radio with Single CD MP3 Player To set the time and date 1 Turn the i
261. kind of extension cord could overheat and cause a fire You could be seriously injured Plug the cord into a properly grounded three prong 110 volt AC outlet If the cord will not reach use a heavy duty three prong extension cord rated for at least 15 amps 4 Before starting the engine be sure to unplug and store the cord as it was before to keep it away from moving engine parts If you do not it could be damaged The length of time the heater should remain plugged in depends on several factors Ask a dealer retailer in the area where you will be parking the vehicle for the best advice on this Features and Controls Automatic Transmission Operation Uplevel The shift lever is located on the console between the seats There are several different positions for the automatic transmission P Park This position locks the front wheels It is the best position to use when starting the engine because the vehicle cannot move easily 2 19 Z CAUTION It is dangerous to get out of the vehicle if the shift lever is not fully in P Park with the parking brake firmly set The vehicle can roll Do not leave the vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure the vehicle will not move even when you are on fairly level ground always set the parking brake and move the shift l
262. l 1 800 553 6000 or write Saturn Corporation 100 Saturn Parkway Mail Drop 371 999 S24 Spring Hill TN 37174 1500 In Canada call 1 800 263 1999 or write Saturn Customer Communication Centre General Motors of Canada Limited CA1 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines transmission axle suspension brakes electrical steering body etc Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks Each bulletin contains instructions to assist in the diagnosis and service of your vehicle Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle The owner manual includes the Maintenance Schedule for all models Customer Assistance Information In Portfolio Includes a Portfolio Owner Manual and Warranty Booklet RETAIL SELL PRICE 35 00 U S plus processing fee Without Portfolio Owner Manual only RETAIL SELL PRICE 25 00 U S plus processing fee Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model GM vehicles To request an order form specify year and model name of the vehicle 7 15 ORDER
263. l designation e Paint information e Production options and special equipment Do not remove this label from the vehicle 5 79 Electrical System Add On Electrical Equipment Notice Do not add anything electrical to the vehicle unless you check with your dealer retailer first Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle s warranty Some add on electrical equipment can keep other components from working as they should Add on equipment can drain the vehicle s battery even if the vehicle is not operating The vehicle has an airbag system Before attempting to add anything electrical to the vehicle see Servicing Your Airbag Equipped Vehicle on page 1 56 5 80 Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse If the motor overheats due to heavy snow or ice the wiper will stop until the motor cools If the overload is caused by some electrical problem have it fixed Power Windows and Other Power Options Circuit breakers in the fuse block protect the power windows and other power accessories When the current load is too heavy the circuit breaker opens and closes protecting the circuit until the problem is fixed or goes away Service and Appearance Care Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by fuses This greatly reduces the c
264. l four tires on a level surface which is level all the way to the wall e The vehicle should be placed so it is perpendicular to the wall or other flat surface e The vehicle should not have any snow ice or mud on it e The vehicle should be fully assembled and all other work stopped while headlamp aiming is being performed e The vehicle should be normally loaded with a full tank of fuel and one person or 160 Ibs 75 kg sitting on the driver s seat e Tires should be properly inflated Headlamp aiming is done with the vehicle s low beam headlamps The high beam headlamps will be correctly aimed if the low beam headlamps are aimed properly Service and Appearance Care To adjust the vertical aim do the following 1 Open the hood See Hood Release on page 5 11 for more information 2 Locate the aim dot on the lens of the low beam headlamp 3 Measure the distance from the ground to the aim dot on the low beam headlamp Record the distance 5 37 Raine 4 At the wall measure from the ground upward A to the recorded distance from Step 3 and mark it 5 Draw or tape a horizontal line B on the wall the width of the vehicle at the height of the mark in Step 4 5 38 Notice Do not cover a headlamp to improve beam cut off when aiming Covering a headlamp may cause excessive heat build up which may cause damage to the headlamp 6 Turn on the low beam headlamps and plac
265. layed on the DIC AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature It also allows you to select which doors and when the doors will automatically unlock See Automatic Door Unlock on page 2 8 for more information Press the customization button until PRESS V TO SET AUTO DOOR UNLOCK appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings OFF None of the doors will automatically unlock DRIVER DOOR AT KEY OUT Only the driver s door will unlock when the key is taken out of the ignition DRIVER DOOR IN PARK Only the driver s door will unlock when the vehicle is shifted into P Park ALL DOORS AT KEY OUT All of the doors will unlock when the key is taken out of the ignition ALL DOORS IN PARK default All of the doors will unlock when the vehicle is shifted into P Park NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Instrument Panel 3 59 REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry RKE transmitter You will not receive feedback when locking the vehicle with the RKE trans
266. lays when the pressure in one or more of the vehicle s tires needs to be checked This message also displays LEFT FRONT RIGHT FRONT LEFT REAR or RIGHT REAR to indicate which tire needs to be checked You can receive more than one tire pressure message at a time To read the other messages that may have been sent at the same time press the set reset button Ifa tire pressure message appears on the DIC stop as soon as you can Have the tire pressures checked and set to those shown on the Tire Loading Information label See Tires on page 5 43 Loading the Vehicle on page 4 28 and Inflation Tire Pressure on page 5 49 The DIC also shows the tire pressure values See DIC Operation and Displays on page 3 42 If the tire pressure is low the low tire pressure warning light comes on See Tire Pressure Light on page 3 34 COMPASS CALIBRATION COMPLETE This message displays when the compass Calibration is complete See DIC Compass on page 3 47 CRUISE CONTROL SET TO XXX This message displays whenever the cruise control is set See Cruise Control on page 3 9 for more information DRIVER DOOR OPEN This message displays when the driver door is not closed properly Close the door completely ENGINE HOT A C Air Conditioning OFF This message displays when the engine coolant becomes hotter than the normal operating temperature To avoid added strain on a hot Instrument Panel 3 51 engine the air conditioning
267. lays when there is a problem with the transmission See your dealer retailer for service SERVICE VEHICLE SOON This message displays when a non emissions related malfunction occurs Have the vehicle serviced by your dealer retailer as soon as possible STABILITRAK NOT READY If your vehicle has StabiliTrak this message may display and the StabiliTrak indicator light on the instrument panel cluster may be on after first driving the vehicle and exceeding 20 mph 32 km h for 30 seconds The StabiliTrak system is not functional until the light has turned off See StabiliTrak System on page 4 7 for more information STABILITRAK OFF If your vehicle has StabiliTrak this message displays when you turn off the StabiliTrak or when the stability control has been automatically disabled To limit wheel spin and realize the full benefits of the stability enhancement system you should normally leave StabiliTrak on However you should turn StabiliTrak off if your vehicle gets stuck in sand mud ice or snow and you want to rock your vehicle to attempt to free it Instrument Panel 3 55 or if you are driving in extreme off road conditions and require more wheel spin See f Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 27 To turn the StabiliTrak system on or off see StabiliTrak System on page 4 7 TIGHTEN GAS CAP This message may display along with the check engine light on the instrument panel c
268. ld the set reset button The display will show zero Fuel Used Press the trip fuel button until FUEL USED displays This display shows the number of gallons gal or liters L of fuel used since the last reset of this menu item To reset the fuel used information press and hold the set reset button while FUEL USED is displayed Elapsed Time Press the trip fuel button until ELAPSED TIME displays This display can be used as a timer To start the timer press the set reset button while ELAPSED TIME is displayed The display will show the amount of time that has passed since the timer was last reset not including time the ignition is off Time will continue to be counted as long as the ignition is on even if another display is being shown on the DIC The timer will record up to 99 hours 59 minutes and 59 seconds 99 59 59 after which the display will return to zero To stop the timer press the set reset button briefly while ELAPSED TIME is displayed To reset the timer to zero press and hold the set reset button while ELAPSED TIME is displayed Instantaneous Fuel Economy If the vehicle has this display press the trip fuel button until INSTANT FUEL ECONOMY displays This display shows the current fuel economy at a particular moment and will change frequently as driving conditions change This display shows the instantaneous fuel economy in miles per gallon mpg or liters per 100 kilometers L 100 km
269. ld restraint in a rear seat position in the vehicle and see your dealer retailer If the Off Indicator is Lit for an Adult Size Occupant If a person of adult size is sitting in the right front passenger seat but the off indicator is lit it could be because that person is not sitting properly in the seat Seats and Restraint System If this happens use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat mounted side impact airbag 1 Turn the vehicle off 2 Remove any additional material from the seat such as blankets cushions seat covers seat heaters or seat massagers 3 Place the seatback in the fully upright position 4 Have the person sit upright in the seat centered on the seat cushion with legs comfortably extended 5 Restart the vehicle and have the person remain in this position for two to three minutes after the on indicator is lit 1 55 Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking which helps the passenger sensing system maintain the passenger airbag status See Safety Belts and Child Restraints in the Index for additional information about the importance of proper restraint use 1 56 A thick layer of additional material such as a blanket or cushion or aftermarket equipment such as seat
270. lder or playlist names Long file folder or playlist names ora combination of a large number of files and folders or playlists can cause the player to be unable to play up to the maximum number of files folders playlists or sessions To play a large number of files folders playlists or sessions minimize the length of the file folder or playlist name Long names also take up more space on the display potentially getting cut off Finalize the audio disc before burning it Trying to add music to an existing disc can cause the disc not to function in the player 3 76 Instrument Panel Playlists can be changed by using the previous and next folder buttons the tune knob or the SEEK arrows An MP3 CD R or CD RW that was recorded using no file folders can also be played If a CD R or CD RW contains more than the maximum of 50 folders 50 playlists and 255 files the player can access and navigate up to the maximum but all items over the maximum are not accessible Root Directory The root directory of the CD R or CD RW is treated as a folder If the root directory has compressed audio files the directory displays as F1 ROOT All files contained directly under the root directory are accessed prior to any root directory folders However playlists Px are always accessed before root folders or files Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that conta
271. le on page 4 32 Antilock Brake System ABS Warning Light For vehicles with the Antilock Brake System ABS this light should come on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer If the ABS light stays on longer than a few seconds after engine is started or comes on and stays on while driving try resetting the system To reset the system 1 While driving pull over when it is safe to do so 2 Place the vehicle in P PARK 3 Turn off the ignition 4 Then restart the engine If the ABS light remains on after resetting the system or comes on again while driving the vehicle needs service If the ABS light is on but the regular brake system warning light is not on the antilock brakes are not working properly but the regular brakes are still functioning Have the vehicle serviced right away If both brake lights are on the vehicle does not have antilock brakes and there is a problem with the regular brakes as well Have the vehicle towed for service See Towing Your Vehicle on page 4 32 Power Steering Warning Lights For 4 cylinder vehicles with Electric Power Steering EPS this light comes on briefly when the ignition is turned to ON RUN as a check to show it is working If it does not come on have the vehicle serviced by your dealer retailer If the EPS light stays on or comes on while driving the EPS system may not b
272. leaning the vehicle s interior only use cleaners specifically designed for the surfaces being cleaned Permanent damage may result from using cleaners on surfaces for which they were not intended Use glass cleaner only on glass Remove any accidental over spray from other surfaces immediately To prevent over spray apply cleaner directly to the cleaning cloth Notice Using abrasive cleaners when cleaning glass surfaces on the vehicle could scratch the glass and or cause damage to the rear window defogger When cleaning the glass on the vehicle use only a soft cloth and glass cleaner Many cleaners contain solvents that may become concentrated in the vehicle s breathing space Before using cleaners read and adhere to all safety instructions on the label While cleaning the vehicle s interior maintain adequate ventilation by opening the vehicle s doors and windows Dust may be removed from small buttons and knobs using a small brush with soft bristles Products that remove odors from the vehicle s upholstery and clean the vehicle s glass can be obtained from your dealer retailer Do not clean the vehicle using A knife or any other sharp object to remove a soil from any interior surface e A stiff brush It can cause damage to the vehicle s interior surfaces e Heavy pressure or aggressive rubbing with a cleaning cloth Use of heavy pressure can damage the interior and does not improve th
273. led if the right front passenger airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag A child in a forward facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position Even if the passenger sensing system has turned off the right front passenger frontal airbag no system is fail safe No one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off Continued Secure rear facing child restraints in a rear seat even if the airbag is off If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go Itis better to secure the child restraint in a rear seat See Passenger Sensing System on page 1 51 for additional information If the vehicle does not have a rear seat that will accommodate a rear facing child restraint a rear facing child restraint should not be installed in the vehicle even if the airbag is off 1 40 If the child restraint has the LATCH system see Lower Anchors and Tethers for Children LATCH on page 1 37 for how and where to install the child restraint using LATCH If a child restraint is secured using a safety belt and it uses a top tether see Lower Anchors and Tethers for Children LATCH
274. led is higher than if the person had not been drinking Control of a Vehicle The following three systems help to control the vehicle while driving brakes steering and accelerator At times as when driving on snow or ice it is easy to ask more of those control systems than the tires and road can provide Meaning you can lose control of the vehicle See Traction Control System TCS on page 4 8 Adding non dealer non retailer accessories can affect vehicle performance See Accessories and Modifications on page 5 3 Braking See Brake System Warning Light on page 3 31 Braking action involves perception time and reaction time Deciding to push the brake pedal is perception time Actually doing itis reaction time Average reaction time is about three fourths of a second But that is only an average It might be less with one driver and as long as two or three seconds or more with another Age physical condition alertness coordination and eyesight all play a part So do alcohol drugs and frustration But even in three fourths of a second a vehicle moving at 60 mph 100 km h travels 66 feet 20 m That could be a lot of distance in an emergency so keeping enough space between the vehicle and others is important And of course actual stopping distances vary greatly with the surface of the road whether it is pavement or gravel the condition of the road whether it is wet dry or icy tire tread
275. ler for service TRACTION CONTROL ON This message displays when the Traction Control System TCS turns on See StabiliTrak System on page 4 7 for more information TRANSMISSION HOT IDLE ENGINE Notice f you drive your vehicle while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and or DIC you can damage the transmission This could lead to costly repairs that would not be covered by your warranty Do not drive your vehicle with overheated transmission fluid or while the transmission temperature warning is displayed This message displays along with a chime if the transmission fluid in the vehicle gets hot Driving with the transmission fluid temperature high can cause damage to the vehicle Stop the vehicle and let it idle to allow the transmission to cool This message clears and the chime stops when the fluid temperature reaches a safe level TURN SIGNAL ON This message displays and a chime sounds as a reminder to turn off the turn signal if you drive your vehicle for more than about 3 4 mile 1 2 km with a turn signal on See Turn and Lane Change Signals on page 3 6 for more information DIC Vehicle Customization Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting Customization features can only be programmed to one setting on the vehicle and cannot be progra
276. limate control system functions as part of the remote start feature See Remote Keyless Entry RKE System Operation on page 2 4 A Fan Control B Temperature Control C Air Delivery Mode Control D Air Conditioning E Outside Air F Recirculation G Rear Window Defogger Instrument Panel 3 17 3 Fan Control Turn clockwise or counterclockwise to increase or decrease the fan speed To turn the fan off turn the left knob all the way counterclockwise In any setting other than off the fan runs continuously with the ignition on There will be some airflow noticeable from the various outlets when driving even with the fan in the off position To turn off the air completely turn the fan to O and select the recirculation button Temperature Control Turn clockwise or counterclockwise to increase or decrease the temperature inside the vehicle Air Delivery Mode Control Turn clockwise or counterclockwise to change the current airflow mode Select from the following air delivery modes 7 Vent Air is directed to the instrument panel outlets 3 18 Instrument Panel 74 Bi Level Air is divided between the instrument panel and the floor outlets tpd Floor Air is directed to the floor outlets with some air directed to the windshield When this mode is selected the system turns the recirculation mode off Recirculation mode cannot be selected while in floor mode This helps prevent window f
277. lose the liftgate completely See Liftgate on page 2 9 OIL PRESSURE LOW STOP ENGINE Notice lf you drive your vehicle while the engine oil pressure is low severe engine damage may occur If a low oil pressure warning appears on the Driver Information Center DIC stop the vehicle as soon as possible Do not drive the vehicle until the cause of the low oil pressure is corrected See Engine Oil on page 5 14 for more information This message displays when the vehicle s engine oil pressure is low The oil pressure light also appears on the instrument panel cluster See Oil Pressure Light on page 3 37 Stop the vehicle immediately as engine damage can result from driving a vehicle with low oil pressure Have the vehicle serviced by your dealer retailer as soon as possible when this message is displayed PASSENGER DOOR OPEN This message displays when one or more of the passenger doors are not closed properly Close the doors completely Instrument Panel 3 53 REMOTE KEY LEARNING ACTIVE This message displays while matching a Remote Keyless Entry RKE transmitter to your vehicle See MATCHING TRANSMITTERS TO YOUR VEHICLE under Remote Keyless Entry RKE System Operation on page 2 4 and DIC Operation and Displays on page 3 42 for more information REMOTE KEY LEARNING COMPLETE This message displays while matching a Remote Keyless Entry RKE transmitter to your vehicle See MATCHING TR
278. luster if the vehicle s fuel cap is not tightened properly See Malfunction Indicator Lamp on page 3 35 Reinstall the fuel cap fully See Filling the Tank on page 5 8 The diagnostic system can determine if the fuel cap has been left off or improperly installed A loose or missing fuel cap allows fuel to evaporate into the atmosphere A few driving trips with the cap properly installed should turn this light and message off 3 56 Instrument Panel TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System TPMS this message displays when the TPMS is re learning the tire positions on your vehicle The tire positions must be re learned after rotating the tires or after replacing a tire or sensor See Tire Inspection and Rotation on page 5 56 Tire Pressure Monitor System on page 5 51 and Inflation Tire Pressure on page 5 49 for more information TRACTION CONTROL OFF This message displays when the Traction Control System TCS turns off See StabiliTrak System on page 4 7 for more information This message only displays while the ignition is in ON RUN and disappears after 10 seconds unless it is acknowledged or an urgent warning appears Any of the following conditions may cause the TCS to turn off e The TCS is turned off by pressing the TCS StabiliTrak button See StabiliTrak System on page 4 7 for more information e The battery is low e There is a TCS failure See your dealer retai
279. m SCC sse O S Passenger Side 16 in 40 0om S s220 o y Rear 12 0 in 20 0 om ezeas OOO O S 6 16 Maintenance Schedule Engine Drive Belt Routing 3 5L V6 LZ4 Engine 2 4L L4 LE5 Engine 3 6L V6 LY7 Engine Maintenance Schedule 6 17 Maintenance Record After the scheduled services are performed record the date odometer reading who performed the service and the type of services performed in the boxes provided See Maintenance Requirements on page 6 1 Any additional information from Owner Checks and Services on page 6 10 can be added on the following record pages You should retain all maintenance receipts Maintenance Record 6 18 Maintenance Schedule Maintenance Record cont d Odometer Maintenance I or 3 Maintenance Schedule 6 19 Maintenance Record cont d Odometer 7 Maintenance I or g 6 20 Maintenance Schedule Maintenance Record cont d Odometer Maintenance I or 3 Customer Assistance Information Customer Assistance and Information Customer Satisfaction Procedure uc seesseesseseeeeeeeeees 7 1 Online Owner Center 7 4 Customer Assistance for Text Telephone TTY WS OPS cn cscncccemadessaeadnedtesaceeds 7 5 Customer Assistance Offices 7 5 GM Mobility Reimbursement Programi ticksiecedacrshaencavennobe 7 6 Roadside Assistance PROGFAM kesesinin 7 6 Scheduling Service Appointments eeseeeeeeees 7 8 Cou
280. matching process is performed successfully See TPMS Sensor Matching Process later in this section One or more TPMS sensors are missing or damaged The TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully See your dealer retailer for service Replacement tires or wheels do not match your vehicle s original equipment tires or wheels Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly See Buying New Tires on page 5 58 Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction TPMS Sensor Matching Process Each TPMS sensor has a unique identification code Any time you replace one or more of the TPMS sensors or rotate the vehicle s tires the identification codes will need to be matched to the new tire wheel position The sensors are matched to the tire wheel positions in the following order driver side front tire passenger side front tire passenger side rear tire and driver side rear tire using a TPMS diagnostic tool See your dealer retailer for service The TPMS sensors can also be matched to each tire wheel position by increasing or decreasing the tire s air pressure When increasing the tire s pressure do not exceed the maximum inflation pressure indicated on t
281. mbined weight of occupants and cargo should never exceed XXX kg or XXX lbs on your vehicle s placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers from XXX kg or XXX Ibs 4 The resulting figure equals the available amount of cargo and luggage load capacity For example if the XXX amount equals 1400 lbs and there will be five 150 Ib passengers in your vehicle the amount of available cargo and luggage load capacity is 650 lbs 1400 750 5 x 150 650 Ibs 5 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4 6 If your vehicle will be towing a trailer the load from your trailer will be transferred to your vehicle Consult this manual to determine how this reduces the available cargo and luggage load capacity for your vehicle See Towing a Trailer on page 4 35 for important information on towing a trailer towing safety rules and trailering tips Driving Your Vehicle 4 29 Ms A B 44 i Example 1 A Vehicle Capacity Weight for Example 1 1 000 Ibs 453 kg B Subtract Occupant Weight 150 Ibs 68 kg x 2 300 Ibs 136 kg C Available Occupant and Cargo Weight 700 Ibs 317 kg 4 30 E c Example 2 A Vehicle Capac
282. mitter if the doors are open See Remote Keyless Entry RKE System Operation on page 2 4 for more information Press the customization button until PRESS V TO SET REMOTE DOOR LOCK appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings VERIFICATION OFF There will be no feedback when you press the lock button on the RKE transmitter 3 60 Instrument Panel VERIFICATION LIGHTS ONLY The exterior lamps will flash when you press the lock button on the RKE transmitter VERIFICATION HORN ONLY The horn will sound on the second press of the lock button on the RKE transmitter VERIFICATION HORN amp LIGHTS default The exterior lamps will flash when you press the lock button on the RKE transmitter and the horn will sound when the lock button is pressed again within five seconds of the previous command VERIFICATION NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry RKE transmitter You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open See Remote Keyless Entry R
283. mmed to a preferred setting for two different drivers All of the customization options may not be available on your vehicle Only the options available will be displayed on the DIC The default settings for the customization features were set when your vehicle left the factory but may have been changed from their default state since then The customization preferences are automatically recalled To change customization preferences use the following procedure Entering the Feature Seitings Menu 1 Turn the ignition on and place the vehicle in P Park To avoid excessive drain on the battery it is recommended that the headlamps are turned off 2 Press the customization button to scroll through the available customizable options Instrument Panel 3 57 Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle DISPLAY IN ENGLISH This feature will only display if a language other than English has been set This feature allows you to change the language in which the DIC messages appear to English Press the customization button until the PRESS TO DISPLAY IN ENGLISH screen appears on the DIC display Press the set reset button once to display all DIC messages in English 3 58 Instrument Panel DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear Press the customization butt
284. mode is chosen as the default display The new track name displays File System and Naming The song name that is displayed is the song name that is contained in the ID3 tag If the song name is not present in the ID3 tag then the radio displays the file name without the extension such as mp3 as the track name Track names longer than 32 characters or four pages are shortened Parts of words on the last page of text and the extension of the filename does not display Preprogrammed Playlists Preprogrammed playlists that were created by WinAmp MusicMatch or Real Jukebox software can be accessed however they cannot be edited using the radio These playlists are treated as special folders containing compressed audio song files Playing an MP3 Insert a CD R or CD RW partway into the slot Single CD Player or press the 7 button and wait for the message to insert disc Six Disc CD Player label side up The player pulls it in and the CD R or CD RW should begin playing If the ignition or radio is turned off with a CD R or CD RW in the player it stays in the player When the ignition or radio is turned on the CD R or CD RW starts to play where it stopped if it was the last selected audio source As each new track starts to play the track number and song title displays Instrument Panel 3 77 4 EJECT Press and release to eject the CD R or CD RW that is playing A beep sounds and Ejec
285. more efficiently For quick cool down on hot days select the following settings together 1 Select 32 mode Select amp 2 3 Turn the lt on 4 Select the coolest temperature and highest fan speed 5 Once the vehicle s interior temperature is below the outside temperature select recirculation mode for enhanced cooling Using these settings together for long periods of time may cause the air inside the vehicle to become too dry To prevent this from happening after the air inside of the vehicle has cooled turn the recirculation mode off The air conditioning system removes moisture from the air so a small amount of water might drip under the vehicle while idling or after turning off the engine This is normal ce Outside Air Press to turn the outside air mode on An indicator light comes on to show that outside air is on Air from outside the vehicle will circulate throughout the vehicle The outside air mode can be used with all modes but it cannot be used with the recirculation mode Pressing this button will cancel the recirculation mode lt amp Recirculation Press to turn on the recirculation mode An indicator light comes on to show that recirculation is on This mode recirculates and helps to quickly cool or heat the air inside the vehicle It can be used to prevent outside air and odors from entering the vehicle Avoid using the recirculation mode during high periods o
286. mp assembly Turn the bulb assembly clockwise until seated Reverse the steps to reinstall the headlamp assembly Taillamps Turn Signal Stoplamps and Back up Lamps To replace one of these bulbs A Taillamp Stoplamp B Turn Signal Lamp C Back up Lamp 1 Open the liftgate f b fi 4 l a i j qi it i MD Remove the two screws holding in the taillamp assembly Slide the taillamp assembly rearward and away from the vehicle Turn the bulb socket being replaced counterclockwise to disconnect it Pull the bulb out of the bulb socket 6 Push the new bulb into the bulb socket Reverse Steps 2 through 4 to reinstall the taillamp assembly ao A o N Service and Appearance Care 5 41 License Plate Lamp To replace one of these bulbs 1 Remove the two screws holding each of the license plate lamps to the fascia 2 Turn and pull the license plate lamp forward through the fascia opening 3 Turn the bulb socket counterclockwise and pull the bulb straight out of the socket 4 Push the new bulb into the bulb socket and turn it clockwise to lock it into place 5 Push and turn the license plate back through the fascia opening 6 Reinstall the two screws holding the license plate lamps to the fascia Replacement Bulbs Exterior Lamp Bulb Number Back up Lamp 3156 Front Turn 3157K Signal Parking Headlam
287. mpletely removed use a mild soap solution and repeat the cleaning process that was used with plain water If any of the soil remains a commercial fabric cleaner or spot lifter may be necessary When a commercial upholstery cleaner or spot lifter is to be used test a small hidden area for colorfastness first If the locally cleaned area gives any impression that a ring formation may result clean the entire surface After the cleaning process has been completed a paper towel can be used to blot excess moisture from the fabric or carpet 5 74 Leather A soft cloth dampened with water can be used to remove dust If a more thorough cleaning is necessary a soft cloth dampened with a mild soap solution can be used Allow the leather to dry naturally Do not use heat to dry Never use steam to clean leather Never use spot lifters or spot removers on leather Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of the leather and are not recommended Do not use silicone or wax based products or those containing organic solvents to clean the vehicle s interior because they can alter the appearance by increasing the gloss in a non uniform manner Never use shoe polish on leather Service and Appearance Care Instrument Panel Vinyl and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust If
288. n once to access the settings for this feature Then press the customization button to scroll through the following settings RESTORE default The customization features will be set to their factory default settings Instrument Panel 3 63 NO CHANGE The customization features will not be set to their factory default settings To select a setting press the set reset button while the desired setting is displayed on the DIC EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu Press the customization button until PRESS V TO EXIT FEATURE SETTINGS appears in the DIC display Press the set reset button once to exit the menu If you do not exit pressing the customization button again will return you to the beginning of the feature settings menu 3 64 Instrument Panel Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs e The vehicle is no longer in ON RUN The trip fuel or vehicle information DIC buttons are pressed e The end of the feature settings menu is reached and exited e A 40 second time period has elapsed with no selection made Audio System s Determine which radio the vehicle has and read the following pages to become familiar with its features Z CAUTION Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others Do not g
289. n Signals When Towing a Trailer The arrows on the instrument panel flash whenever signaling a turn or lane change Properly hooked up the trailer lamps also flash telling other drivers the vehicle is turning changing lanes or stopping When towing a trailer the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out For this reason you may think other drivers are seeing the Driving Your Vehicle signal when they are not It is important to check occasionally to be sure the trailer bulbs are still working Driving on Grades Notice Do not tow on steep continuous grades exceeding 6 miles 9 6 km Extended higher than normal engine and transmission temperatures may result and damage the vehicle Frequent stops are very important to allow the engine and transmission to cool Vehicles can tow in D Drive Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and or hilly conditions Reduce speed and shift to a lower gear before starting down a long or steep downgrade If the transmission is not shifted down the brakes might have to be used so much that they would get hot and no longer work well On a long uphill grade shift down and reduce the vehicle s speed to around 45 mph 70 km h to reduce the possibility of the engine and the transmission overheating When towing at high altitude on steep uphill grades consider t
290. n Weight Rating of 14 000 Ibs 6 350 kg The trailer rating should be 14 000 Ibs 6350 kg 5 500 Ibs 2495 kg 8 500 Ibs 3855 kg GCWR Vehicle Weight Trailer Rating Expect tongue weight to be at least 10 percent of trailer weight 850 Ibs 386 kg and because the weight is applied well behind the rear axle the effect on the rear axle is greater than just the weight itself as much as 1 5 times as much The weight at the rear axle could be 850 Ibs 386 kg X 1 5 1 275 lbs 578 kg Since the rear axle already weighs 2 700 lbs 1 225 kg adding 1 275 lbs 578 kg brings the total to 3 975 lbs 1 803 kg This is very close to but within the limit for RGAWR as well The vehicle is set to trailer up to 8 500 Ibs 3 856 kg If the vehicle has many options and there is a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well 300 lbs 136 kg could be added to the front axle weight and 400 Ibs 181 kg to the rear axle weight The vehicle now weighs 2 800 Ibs 1270 kg 300 lbs 136 kg Front 2 700 Ibs 1225 kg 400 Ibs 181 kg Rear 6 200 Ibs 2812 kg Total Weight is still below 7 200 Ibs 3 266 kg and you might think 700 additional pounds 318 kg should be subtracted from the trailering capacity to stay within GCWR limits The maximum trailer would only be 7 800 Ibs 3 538 kg You may go further and think the tongue weight should be limited to les
291. n in the rear seat use the window lockout button to prevent unintentional operation of the windows 2 11 Features and Controls The window switches for all doors are located on the driver door Each door also has a switch To open or close a window press or pull up on the switch The power windows operate when the ignition is in ON RUN or ACC ACCESSORY or while in Retained Accessory Power RAP See Retained Accessory Power RAP on page 2 17 Express Down Window The driver window switch has an express down feature that lowers the window without holding the switch Press the switch part way and the window will open a small amount Press the switch down all the way and release it and the window lowers all the way To stop the window while it is lowering press and release the switch Window Lockout fa Window Lockout The vehicle has a lockout feature to prevent rear seat passengers from operating the windows Press the lockout button located with the power window switches to turn the feature on and off Sun Visors To block out glare swing the sun visor down or detach the driver sun visor from the center mount and slide it along the rod from side to side On a visor with a mirror lift the cover to use it 2 12 Theft Deterrent Systems Vehicle theft is big business especially in some cities This vehicle has theft deterrent features however they do not make it imposs
292. n of the gas pedal may allow you to gain more traction on slippery surfaces With the Manual Shift Mode the vehicle can accelerate from a stop in 2 Second or 3 Third 1 Move the shift lever from D Drive into the manual gate 2 With the vehicle stopped move the shift lever forward to select 2 Second or 3 Third The vehicle will start from a stop position in 2 Second or 3 Third 3 Once the vehicle is moving select the desired drive gear or move the shift lever to the D Drive position 2 22 Automatic Transmission Operation Base The shift lever is located on the console between the seats There are several different positions for the automatic transmission P Park This position locks the front wheels It is the best position to use when you start the engine because the vehicle cannot move easily Features and Controls Z CAUTION It is dangerous to get out of the vehicle if the shift lever is not fully in P Park with the parking brake firmly set The vehicle can roll Do not leave the vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure the vehicle will not move even when you are on fairly level ground always set the parking brake and move the shift lever to P Park See Shifting Into Park Automatic Transmission on page 2 25 lf you are pulling a trailer
293. nd in vehicle transmitters for garage door openers RFID technology in Saturn vehicles does not use or record personal information or link with any other Saturn system containing personal information 7 18 Customer Assistance Information 4 NOTES A About Driving Your Vehicle ii Accessories and Modifications 2 00 5 3 Accessory Power 2 17 Accessory Power Outlets 3 16 Adding Equipment to Your Airbag Equipped Vehicle 1 57 Additional Required Services Scheduled Maintenance 6 6 Additives Fuel 6068 5 6 Add On Electrical Equipment porcen 5 79 Adjustment Chime Level 055 3 93 Air Cleaner Filter Engine 5 17 Air Conditioning 0 3 17 Air Filter Passenger Compartment 0 3 24 Airbag Readiness Light 3 29 Airbag System eeeeeeeee 1 42 Adding Equipment to Your Airbag Equipped Vehicle cceeeeees 1 57 How Does an Airbag Restrain n a 1 49 Airbag System cont Passenger Sensing SYSTEMA sonsonen 1 51 Servicing Your Airbag Equipped Vehicle crisser 1 56 What Makes an Airbag Inflate oenina 1 49 What Will You See After an Airbag Inflates 1 50 When Should an Airbag Inflate oinnia 1 47 Where Are the Airbags 1 45 Airbags Passenger Status Indication 3 30 All Wheel Drive 5 5 35 All Wheel Drive Disabled Light ses
294. nd begins playing MP3 files by that artist To listen to MP3 files by another artist press the pushbutton located below either arrow button The disc goes to the next or previous artist in alphabetical order Continue pressing either button until the desired artist is displayed To change from playback by artist to playback by album press the pushbutton located below the Sort By label From the sort screen push one of the buttons below the album button Press the pushbutton below the back label to return to the main music navigator screen Now the album name is displayed on the second line between the arrows and songs from the current album begins to play Once all songs from that album are played the player moves to the next album in alphabetical order on the CD R CD RW and begins playing MP3 files from that album To exit music navigator mode press the pushbutton below the Back label to return to normal MP3 playback BAND Press to listen to the radio while a CD is playing The inactive CD remains inside the radio for future listening CD AUX CD Auxiliary Press to play a CD while listening to the radio The CD icon and a message showing disc and or track number displays while a CD is in the player Press this button again and the system automatically searches for an auxiliary input device such as a portable audio player If a portable audio player is not connected No Aux Input Device displays I
295. nd cargo Service and Appearance Care DOT Markings A code molded into the sidewall of a tire signifying that the tire is in compliance with the U S Department of Transportation DOT motor vehicle safety standards The DOT code includes the Tire Identification Number TIN an alphanumeric designator which can also identify the tire manufacturer production plant brand and date of production GVWR Gross Vehicle Weight Rating See Loading the Vehicle on page 4 28 GAWR FRT Gross Axle Weight Rating for the front axle See Loading the Vehicle on page 4 28 GAWR RR Gross Axle Weight Rating for the rear axle See Loading the Vehicle on page 4 28 5 47 Intended Outboard Sidewall The side of an asymmetrical tire that must always face outward when mounted on a vehicle Kilopascal kPa The metric unit for air pressure Light Truck LT Metric Tire A tire used on light duty trucks and some multipurpose passenger vehicles Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire Maximum Inflation Pressure The maximum air pressure to which a cold tire can be inflated The maximum air pressure is molded onto the sidewall Maximum Load Rating The load rating for a tire at the maximum permissible inflation pressure for that tire 5 48 Maximum Loaded Vehicle Weight The sum of curb weight accessory weight vehicle capacity weight and
296. nd safe location such as an open parking lot where driving the vehicle in circles is not a danger It is suggested to calibrate away from tall buildings utility wires manhole covers or other industrial structures if possible If CAL should ever appear in the DIC display the compass should be calibrated If the DIC display does not show a heading for example N for North or the heading does not change after making turns there may be a strong magnetic field interfering with the compass Such interference may be caused by a magnetic CB or cell phone antenna mount a magnetic emergency light magnetic note pad holder or any other magnetic item Turn off the vehicle move the magnetic item then turn on the vehicle and calibrate the compass To calibrate the compass use the following procedure Compass Calibration Procedure 1 Before calibrating the compass make sure the compass is set to the variance zone in which the vehicle is located See Compass Variance Zone Procedure earlier in this section Do not operate any switches such as window sunroof climate controls seats etc during the calibration procedure Press the vehicle information button until PRESS V TO CALIBRATE COMPASS displays Press the set reset button to start the compass calibration The DIC will display CALIBRATING COMPASS TURN IN CIRCLES Drive the vehicle in tight circles at less than 5 mph 8 km h to comple
297. ndicator in the instrument panel comes on when the fog lamps are in use The parking lamps or low beam headlamps must be on before the fog lamps can be turned on If the exterior lamp control is set to AUTO mode the parking lamps and low beam headlamps come on simultaneously when the fog lamps are turned on When the high beam headlamps are turned on the fog lamps turn off automatically When the high beam headlamps are turned off the fog lamps come on again Some localities have laws that require the headlamps to be on along with the fog lamps Instrument Panel Brightness This feature controls the brightness of the instrument panel lights The thumbwheel for this feature is located on the left side of the steering wheel next to the exterior lamps control Turn the thumbwheel to the right or left to brighten or dim the lights Dome Lamp X Dome Lamp Override Press this button to keep the dome lamps and other interior lamps turned off while any door is open Press this button again to return it to the out position and the lamps automatically come on when any door is opened x On Off Press this button to turn the dome lamps on and off while the doors are closed Entry Lighting If the dome lamp override button is in the out position the lamps inside the vehicle automatically come on when any door is opened or when the Remote Keyless Entry RKE unlock button is pressed After the door
298. nditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger Service and Appearance Care car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law It should be noted that the temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 5 61 Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis However if you notice unusual tire wear or your vehicle pulling to one side or the other the alignment might need to be checked If you notice your vehicle vibrating when driving on a smooth road the tires and wheels might need to be rebalanced See your dealer retailer for proper diagnosis 5 62 Wheel Replacement Replace any wheel that is bent cracked or badly rus
299. ne right away Make sure the safety belt reminder light is working See Safety Belt Reminders on page 3 28 for more information Keep safety belts clean and dry See Care of Safety Belts on page 5 74 Airbags The airbag system does not need regularly scheduled maintenance or replacement Make sure the airbag readiness light is working See Airbag Readiness Light on page 3 29 for more information Notice f an airbag covering is damaged opened or broken the airbag may not work properly Do not open or break the airbag coverings If there are any opened or broken airbag covers have the airbag covering and or airbag module replaced For the location of the airbag modules see What Makes an Airbag Inflate on page 1 49 See your dealer retailer for service Replacing Restraint System Parts After a Crash Z CAUTION A crash can damage the restraint systems in your vehicle A damaged restraint system may not properly protect the person using it resulting in serious injury or even death in a crash To help make sure your restraint systems are working properly after a crash have them inspected and any necessary replacements made as soon as possible Seats and Restraint System If the vehicle has been in a crash do you need new safety belts or LATCH system if equipped parts After a very minor crash nothing may be necessary But the safety belt assemblies that were used during an
300. ned for them Every time infants and young children ride in vehicles they should have the protection provided by appropriate child restraints Children who are not restrained properly can strike other people or can be thrown out of the vehicle Z CAUTION Never do this Never hold an infant or a child while riding in a vehicle Due to crash forces an infant or a child will become so heavy it is not possible to hold it during a crash For example in a crash at only 25 mph 40 km h a 12 Ib 5 5 kg infant will suddenly become a 240 Ib 110 kg force ona person s arms An infant should be secured in an appropriate restraint Seats and Restraint System 1 27 Z CAUTION Never do this Children who are up against or very close to any airbag when it inflates can be seriously injured or killed Never put a rear facing child restraint in the right front seat Secure a rear facing child restraint in a rear seat It is also better to secure a forward facing child restraint in a rear seat If you must secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go 1 28 Q What are the different types of add on child restraints A Add on child restraints which are purchased by the vehicle s owner are available in four basic types Selection of a particular restraint should take into consideration not o
301. ng airbag A child in a forward facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position Continued CAUTION Continued Even if the passenger sensing system has turned off the right front passenger frontal airbag and seat mounted side impact airbag if equipped no system is fail safe No one can guarantee that an airbag will not deploy under some unusual circumstance even though the airbag s are off Secure rear facing child restraints in a rear seat even if the airbag s are off If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go It is better to secure the child restraint in a rear seat If the vehicle does not have a rear seat that will accommodate a rear facing child restraint a rear facing child restraint should not be installed in the vehicle even if the airbag is off Seats and Restraint System The passenger sensing system is designed to turn off the right front passenger airbag and seat mounted side impact airbag if e The right front passenger seat is unoccupied e The system determines that an infant is present in a rear facing infant seat e The system determines that a small child is present in a child restraint e The system determines that a small child is present in a booster seat
302. ng your doors can help prevent this from happening To lock or unlock a door use the key from the outside or the door lock from the inside 2 8 Features and Controls Power Door Locks amp The power door lock switches are located on the driver door e Press the right side of the switch to unlock the doors e Remove the ignition key and press the left side of the switch to lock all of the doors Delayed Locking A chime will sound to indicate a door or liftgate is open when you try to lock the doors with the power door lock switch The doors will not lock and the theft deterrent system will not arm until all the doors are closed and five seconds have passed Automatic Door Lock The doors are programmed to automatically lock when the shift lever is moved into a forward gear The automatic door lock feature cannot be disabled Automatic Door Unlock The doors will automatically unlock when the shift lever is moved into P Park Rear Door Security Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside Open the rear doors to access the security locks on the inside edge of each door To set the locks insert a key into the slot and turn it to the horizontal position The door can only be opened from the outside with the door unlocked To return the door to normal operation turn the slot to the vertical position Locko
303. ning You need new tires if any of the following statements are true e You can see the indicators at three or more places around the tire e You can see cord or fabric showing through the tire s rubber e The tread or sidewall is cracked cut or snagged deep enough to show cord or fabric e The tire has a bump bulge or split e The tire has a puncture cut or other damage that cannot be repaired well because of the size or location of the damage The rubber in tires degrades over time even if they are not being used This is also true for the spare tire if the vehicle has one Multiple conditions affect how fast this aging takes place including temperatures loading conditions and inflation pressure maintenance With proper care and maintenance tires typically wear out before they degrade due to age If you are unsure about the need to replace the tires as they get older consult the tire manufacturer for more information 5 58 Buying New Tires GM has developed and matched specific tires for your vehicle The original equipment tires installed on your vehicle when it was new were designed to meet General Motors Tire Performance Criteria Specification TPC Spec system rating If you need replacement tires GM strongly recommends that you get tires with the same TPC Spec rating This way your vehicle will continue to have tires that are designed to give the same performance and vehicle safety
304. nly as needed to keep warm but be careful To save fuel run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat Repeat this until help arrives but only when you feel really uncomfortable from the cold Moving about to keep warm also helps If it takes some time for help to arrive now and then when you run the engine push the accelerator pedal slightly so the engine runs faster than the idle speed This keeps the battery charged to restart the vehicle and to signal for help with the headlamps Do this as little as possible to save fuel If Your Vehicle is Stuck in Sand Mud Ice or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand mud ice or snow See Rocking Your Vehicle to Get It Out on page 4 27 If the vehicle has a traction system it can often help to free a stuck vehicle Refer to the vehicle s traction system in the Index If stuck too severely for the traction system to free the vehicle turn the traction system off and use the rocking method Driving Your Vehicle Z CAUTION If you let your vehicle s tires spin at high speed they can explode and you or others could be injured The vehicle can overheat causing an engine compartment fire or other damage Spin the wheels as little as possible and avoid going above 35 mph 55 km h as shown on the speedometer
305. nly the child s weight height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used For most basic types of child restraints there are many different models available When purchasing a child restraint be sure it is designed to be used in a motor vehicle If it is the restraint will have a label saying that it meets federal motor vehicle safety standards The restraint manufacturer s instructions that come with the restraint state the weight and Seats and Restraint System height limitations for a particular child restraint In addition there are many kinds of restraints available for children with special needs Z CAUTION To reduce the risk of neck and head injury during a crash infants need complete support This is because an infant s neck is not fully developed and its head weighs so much compared with the rest of its body In a crash an infant in a rear facing child restraint settles into the restraint so the crash forces can be distributed across the strongest part of an infant s body the back and shoulders Infants should always be secured in rear facing Z CAUTION A young child s hip bones are still so small that the vehicle s regular safety belt may not remain low on the hip bones as it should Instead it may settle up around the child s abdomen In a crash the belt would apply force on a body area
306. nsportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion Collision Damage Repair If your vehicle is involved in a collision and it is damaged have the damage repaired by a qualified technician using the proper equipment and quality replacement parts Poorly performed collision repairs diminish your vehicle s resale value and safety performance can be compromised in subsequent collisions Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built Genuine GM Collision parts are your best choice to ensure that your vehicle s designed appearance durability and safety are preserved The use of Genuine GM parts can help maintain your GM New Vehicle Warranty Recycled original equipment parts may also be used for repair These parts are typically removed from vehicles that were total losses in prior crashes In most cases the parts being recycled are from undamaged sections of the vehicle A recycled original equipment GM part may be an acceptable choice to maintain your vehicle s originally designed appearance and safety performance however the history of these parts is not known Such parts are not covered by your GM New Vehicle Limited Warranty and any related failures are not covered by that warranty
307. nstrument Panel 3 79 XM Radio Messages XL Explicit Language Channels These channels or any others can be blocked at a customer s request by calling 1 800 852 XMXM 9696 XM Updating The encryption code in the receiver is being updated and no action is required This process should take no longer than 30 seconds No XM Signal The system is functioning correctly but the vehicle is in a location that is blocking the XM signal When the vehicle is moved into an open area the signal should return Loading XM The audio system is acquiring and processing audio and text data No action is needed This message should disappear shortly 3 80 Instrument Panel Channel Off Air This channel is not currently in service Tune in to another channel Channel Unauth This channel is blocked or cannot be received with your XM Subscription package Channel Unavail This previously assigned channel is no longer assigned Tune to another station If this station was one of the presets choose another station for that preset button No Artist Info No artist information is available at this time on this channel The system is working properly No Title Info No song title information is available at this time on this channel The system is working properly No CAT Info No category information is available at this time on this channel The system is working properly No Information No text or informati
308. nt laws including speed limit restrictions having to do with trailering Make sure the rig will be legal not only where you live but also where you will be driving A good source for this information can be state or provincial police Do not tow a trailer at all during the first 500 miles 800 km the new vehicle is driven The engine axle or other parts could be damaged Then during the first 500 miles 800 km that a trailer is towed do not drive over 50 mph 80 km h and do not make starts at full throttle This helps the engine and other parts of the vehicle wear in at the heavier loads e Vehicles can tow in D Drive Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and or hilly conditions e Obey speed limit restrictions when towing a trailer Do not drive faster than the maximum posted speed for trailers or no more than 55 mph 90 km h to save wear on the vehicle s parts e Do not tow a trailer when the outside temperature is above 100 F 38 C Three important considerations have to do with weight e The weight of the trailer e The weight of the trailer tongue e The total weight on the vehicle s tires 4 37 Driving Your Vehicle Weight of the Trailer How heavy can a trailer safely be It depends on how the rig is used For example speed altitude road grades outside temperature and how much the vehicle is used to pull a trailer
309. nt for reasonable fuel expenses may be available Claim amounts should reflect actual costs and be supported by original receipts See your retailer for information regarding the allowance amounts for reimbursement of fuel or other transportation costs 7 10 Courtesy Rental Vehicle Your retailer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair Rental reimbursement will be limited and must be supported by original receipts This requires that you sign and complete a rental agreement and meet state provincial local and rental vehicle provider requirements Requirements vary and may include minimum age requirements insurance coverage credit card etc You are responsible for fuel usage charges and may also be responsible for taxes levies usage fees excessive mileage or rental usage beyond the completion of the repair It may not be possible to provide a like vehicle as a courtesy rental Customer Assistance Information Additional Program Information All program options such as shuttle service may not be available at every retailer Please contact your retailer for specific information about availability All Courtesy Transportation arrangements will be administered by appropriate retailer personnel Saturn reserves the right to unilaterally modify change or discontinue Courtesy Tra
310. ntiveness and judgment can be affected by even a small amount of alcohol You can have a serious or even fatal collision if you drive after drinking Do not drink and drive or ride with a driver who has been drinking Ride home in a cab or if you are with a group designate a driver who will not drink Death and injury associated with drinking and driving is a global tragedy Alcohol affects four things that anyone needs to drive a vehicle judgment muscular coordination vision and attentiveness Police records show that almost 40 percent of all motor vehicle related deaths involve alcohol In most cases these deaths are the result of someone who was drinking and driving In recent years more than 17 000 annual motor vehicle related deaths have been associated with the use of alcohol with about 250 000 people injured For persons under 21 it is against the law in every U S state to drink alcohol There are good medical psychological and developmental reasons for these laws The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive Medical research shows that alcohol in a person s system can make crash injuries worse especially injuries to the brain spinal cord or heart This means that when anyone who has been drinking driver or passenger is in a crash that person s chance of being killed or permanently disab
311. ntrol system Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off 3 12 Instrument Panel Exterior Lamps The exterior lamp control is located on the instrument panel to the left of the steering wheel The exterior lamp control can be turned to the following positions O Off Turns off the exterior lamps The knob returns to the AUTO position after it is released AUTO Automatic Automatically turns the exterior lamps on and off depending on outside lighting D0 Parking Lamps Turns on the parking lamps together with the following e Sidemarker Lamps Taillamps e License Plate Lamps e Instrument Panel Lights ZD Headlamps Turns on the headlamps together with the previously listed lamps and lights Lamps On Reminder A warning chime sounds if the driver door is opened while the ignition is off and the lamps are on Wiper Activated Headlamps This feature automatically turns on the headlamps and parking lamps if the exterior lamp control is set in the AUTO position and the windshield wipers are turned on and have completed eight wipe cycles See Exterior Lamps on page 3 12 for additional information When the ignition is turned off the wiper activated headlamps immediately turn off They also turn off if the windshield wiper control is turned off Daytime Running Lamps DRL Daytime Running Lamps DRL can
312. o turn on the heated seat The indicator light on the button shows that the feature is on and the level of heat three being the highest Press the button to choose the level of heat The passenger seat may take longer to heat up 1 6 Seats and Restraint System Reclining Seatbacks Manual Reclining Seatbacks Z CAUTION You can lose control of the vehicle if you try to adjust a manual driver s seat while the vehicle is moving The sudden movement could startle and confuse you or make you push a pedal when you do not want to Adjust the drivers seat only when the vehicle is not moving Z CAUTION If either seatback is not locked it could move forward in a sudden stop or crash That could cause injury to the person sitting there Always push and pull on the seatbacks to be sure they are locked fa x On seats with manual reclining seatbacks the lever used to operate them is located on the outboard side of the seat To recline the seatback 1 Lift the recline lever 2 Move the seatback to the desired position then release the lever to lock the seatback in place 3 Push and pull on the seatback to make sure it is locked To return the seatback to an upright position 1 Lift the lever fully without applying pressure to the seatback and the seatback returns to the upright position 2 Push and pull on the seatback to make sure it is locked Seats and Restraint
313. ock is located on the driver side of the engine compartment near the battery Notice Spilling liquid on any electrical components on the vehicle may damage it Always keep the covers on any electrical component Service and Appearance Care 5 83 Fuses Te Control Eog Not Used S ROOF Sunroof Module HTD SEAT ee Seat Control Body Control Fess veer FAN MAIN Cooling Fan Main A anma STRTR Starter Motor odule REAR WPR Rear Wiper Motor EcM tcwy Transmission Windshield Wiper Control Module FAN AUX peer Fan SGCM Serial Data Gateway ial J Communication Module 5 84 All Wheel Drive 4WD ESCM System Antilock Brake System Module Air Conditioning BLWR MTR Blower Motor Antilock Brake System Module Instrument Panel P BEC Bussed Electrical Center Service and Appearance Care Fuses Usage FRT FOG Front Fog Lamps Instrument Panel P BEC _ Bussed Electrical Center Daytime Running Right Turn and T LAMP RT Parking Lamps Left Turn and TAME LT Parking Lamps TRLR Trailer Parking T LAMP Lamps Passenger Side HDLP HI LT High Beam Headlamp STOP LP Stoplamps DEFOG _ Defroster Fog Driver Side Low Beam Headlamp HDLP LO RT Driver Side High Beam Headlamp Outside Rearview Mirror Heating HDLP HI RT OSRVM HTR Passenger Side io a Low Beam Headlamp Relays Usage FAN MAIN Cooling Fan Main RLY Relay FAN CTRL Cooling Fan Control RLY Rel
314. ogging Pd Defog This mode clears the windows of fog or moisture Air is directed to the floor outlets with some air directed to the windshield and side window outlets In this mode the system turns the recirculation mode off and runs the air conditioning compressor unless the outside air is at or below freezing Recirculation mode cannot be selected while in defog mode This helps prevent window fogging W Defrost This mode removes fog or frost from the windshield more quickly Air is directed to the windshield and the side window outlets In this mode the system turns the recirculation mode off automatically and runs the air conditioning compressor unless the outside air is at or below freezing Recirculation mode cannot be selected while in defrost mode This helps prevent window fogging For best results clear all snow and ice from the windshield before defrosting Air Conditioning Press to turn the air conditioning system on or off An indicator light comes on to show that the air conditioning is on The air conditioning can be selected in any mode as long as the fan is on and the outside temperature is above freezing A flashing indicator light indicates that the air conditioning compressor is currently not available On hot days open the windows to let hot inside air escape then close them This helps reduce the time it takes for the vehicle to cool down and helps the system to operate
315. ollow the advice in this section and see your dealer retailer for important information about towing a trailer with the vehicle The vehicle can tow a trailer if it is equipped with the proper trailer towing equipment To identify the trailering capacity of the vehicle read the information in Weight of the Trailer that appears later in this section Trailering is different than just driving the vehicle by itself Trailering means changes in handling acceleration braking durability and fuel economy Successful safe trailering takes correct equipment and it has to be used properly 4 36 The following information has many time tested important trailering tips and safety rules Many of these are important for your safety and that of your passengers So please read this section carefully before pulling a trailer Load pulling components such as the engine transmission rear axle wheel assemblies and tires are forced to work harder against the drag of the added weight The engine is required to operate at relatively higher speeds and under greater loads generating extra heat The trailer also adds considerably to wind resistance increasing the pulling requirements The vehicle has Trailer Sway Control TSC See Trailer Sway Control TSC in StabiliTrak System on page 4 7 for more information Driving Your Vehicle Pulling A Trailer Here are some important points e There are many differe
316. olume level appears on the radio display Removing the radio and not replacing it with a factory radio or chime module will disable vehicle chimes 3 94 Instrument Panel 4 NOTES Driving Your Vehicle Your Driving the Road and the Vehicle Driving Your Vehicle Driver Behavior 0006 Driving Environment Vehicle Design Driving for Better Fuel Economy Defensive Driving Drunk Driving oee Control of a Vehicle Braking eeeeeeeeee eee ee eee Antilock Brake System ABS Braking in Emergencies StabiliTrak System Traction Control System TCS ceecee All Wheel Drive AWD SYSTEM siecceseccsaseasecsnneenccs SH GHING E Off Road Recovery seee 4 11 PASSING siecssesccaacctiancqoessdepeeg 4 11 Loss of Control discriminer 4 12 Off Road Driving eseese 4 13 Driving at Night s s 4 22 Driving in Rain and on Wet Roads sseseeeeee 4 23 Before Leaving on A LONG Trip eeeeeeeeeeeeee ees 4 24 Highway Hypnosis 4 24 Hill and Mountain Roads 4 24 Winter Driving ce00ee 4 25 If Your Vehicle is Stuck in Sand Mud Ice or Snow 4 27 Rocking Your Vehicle to Get It Out cctesiaccnteests ects 4 27 Loading the Vehicle 4 28 Towing Towing Your Vehicle 4 32 Recreational Vehicle Towing 4 32 Towing a Trailer ceee
317. olve your concerns 7 2 Normally concerns can be quickly resolved at this level STEP TWO Should you need additional assistance in the U S contact the Saturn Customer Assistance Center by calling 1 800 553 6000 In Canada call the Saturn Customer Communication Centre at 1 800 263 1999 A Saturn Customer Assistance Center team member will handle your call and assist in providing product and warranty information the nearest retailer location roadside assistance brochures literature and discuss any concerns you may have Customer Assistance Information We encourage you to call the toll free number in order to give your inquiry prompt attention Please have the following information available to give the Customer Assistance Representative e Vehicle Identification Number VIN This 17 digit number can be found on the vehicle registration or title on the upper driver side corner of the instrument panel or on your roadside assistance key card The name of your selling and servicing retail facility e Vehicle delivery date and present mileage e Your daytime and evening phone numbers When contacting Saturn please remember that your concern will likely be resolved at a retailer s facility That is why we suggest you follow Step One first STEP THREE U S Owners Both Saturn and its retailers are committed to making sure you are completely satisfied with your Saturn vehicle However if you
318. ompact Spare Tire on page 5 71 for more information 5 66 The tools are located between the compact spare tire and the liftgate To access the tools Tool Bag Wing bolt Jack Ow gt e Remove the wing bolt B from the jack 2 Remove the jack C and tool bag A Service and Appearance Care 3 Remove the straps holding the bag containing the wheel wrench and extension jack handle Remove the wheel wrench and extension jack handle from the bag The tools you will be using include A Tool Bag B Jack C Wheel Wrench D Extension Jack Handle Removing the Flat Tire and Installing the Spare Tire 1 Do a safety check before proceeding See Changing a Flat Tire on page 5 64 for more information ay Ch We a r 2 Use the wheel wrench to loosen all the wheel nuts Do not remove them yet 3 Attach the wheel wrench to the jack bolt head and rotate the wheel wrench clockwise to raise the lift head a little 4 Position the lift head at the jack location nearest the flat tire Make sure all of the jack lift head is touching the jacking flange under the body Do not place the jack under a body panel The lower body panel has an arrow to aid in locating the jacking location 5 Put the compact spare tire near you Service and Appearance Care 6 Raise the vehicle by turning the jack handle clockwise Raise the vehicle far enough off the ground
319. on eee 7 1 Customer Assistance and Information ee eee 7 1 Reporting Safety DefectS cece ee eeeee eee 7 14 Vehicle Data Recording and Privacy 068 16 Indek aiceiokscetecleidae i 1 ii Preface d El SATURN the SATURN Emblem and the name VUE are registered trademarks of Saturn Corporation GENERAL MOTORS and GM are registered trademarks of General Motors Corporation This manual includes the latest information at the time it was printed Saturn reserves the right to make changes after that time without further notice This manual describes features that may or may not be on your specific vehicle Litho in U S A Part No 25812262 B Second Printing Read this manual from beginning to end to learn about the vehicle s features and controls Pictures symbols and words work together to explain vehicle operation Keep this manual in the vehicle for quick reference Canadian Owners A French language copy of this manual can be obtained from your dealer retailer or from Helm Incorporated P O Box 07130 Detroit MI 48207 1 800 551 4123 www helminc com Propri taires Canadiens On peut obtenir un exemplaire de ce guide en fran ais aupr s de concessionnaire ou l adresse suivante Helm Incorporated P O Box 07130 Detroit MI 48207 1 800 551 4123 www helminc com About Driving Your Vehicle As with other vehicles of this type failure to operat
320. on page 6 13 Maintenance Schedule At Each Fuel Fill It is important to perform these underhood checks at each fuel fill Engine Oil Level Check Notice It is important to check the engine oil regularly and keep it at the proper level Failure to keep the engine oil at the proper level can cause damage to the engine not covered by the vehicle warranty Check the engine oil level and add the proper oil if necessary See Engine Oil on page 5 14 Engine Coolant Level Check Check the engine coolant level and add DEX COOL coolant mixture if necessary See Engine Coolant on page 5 22 Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary At Least Once a Month Tire Inflation Check Inspect the vehicle s tires and make sure they are inflated to the correct pressures Do not forget to check the spare tire See Inflation Tire Pressure on page 5 49 Check to make sure the spare tire is stored securely See Changing a Flat Tire on page 5 64 Tire Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification Check the tires for wear and if necessary rotate the tires See Tire Inspection and Rotation on page 5 56 At Least Once a Year Starter Switch Check Z CAUTION When you are doing this inspection the vehicl
321. on the cell phone that will be paired to the vehicle Reference the cell phone manufacturers user guide for information on this process Locate the device named General Motors in the list on the cellular phone and follow the instructions on the cell phone to enter the four digit PIN number that was provided in Step 3 The system prompts for a name for the phone Use a name that best describes the phone This name will be used to indicate which phone is connected The system then confirms the name provided The system responds with lt Phone name gt has been successfully paired after the pairing process is complete Repeat Steps 1 through 7 for additional phones to be paired Listing All Paired and Connected Phones 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Bluetooth The system responds with Bluetooth ready followed by a tone 3 Say List The system lists all the paired Bluetooth devices If a phone is connected to the vehicle the system will say Is connected after the connected phone Deleting a Paired Phone 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Bluetooth The system responds with Bluetooth ready followed by a tone 3 Say Delete The system asks which phone to delete followed by a tone 4 Say the
322. on until the PRESS TO SET DISPLAY LANGUAGE screen appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings ENGLISH default All messages will appear in English FRANCAIS All messages will appear in French ESPANOL All messages will appear in Spanish PORTUGUESE All messages will appear in Portuguese NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC AUTO DOOR LOCK This feature allows you to select when the vehicle s doors will automatically lock See Automatic Door Lock on page 2 8 for more information Press the customization button until PRESS V TO SET AUTO DOOR LOCK appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings SHIFT OUT OF PARK default The doors will automatically lock when the vehicle is shifted out of P Park AT VEHICLE SPEED The doors will automatically lock when the vehicle speed is above 8 mph 13 km h for three seconds NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is disp
323. onal messages are available at this time on this channel The system is working properly CAT Not Found There are no channels available for the selected category The system is working properly XM Theftlocked The XM receiver in the vehicle could have previously been in another vehicle For security purposes XM receivers cannot be swapped between vehicles If this message is received after having the vehicle serviced check with your dealer retailer XM Radio ID If tuned to channel 0 this message alternates with the XM Radio 8 digit radio ID label This label is needed to activate the service Unknown If this message is received when tuned to channel 0 there could be a receiver fault Consult with your dealer retailer Check XM Receivr If this message does not clear within a short period of time the receiver could have a fault Consult with your dealer retailer XM Not Available If this message does not clear within a short period of time the receiver could have a fault Consult with your dealer retailer Navigation Radio System For vehicles with a navigation radio system see the separate Navigation System manual Bluetooth Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls The system can be used while the key is in ON RUN or ACC ACCESSORY position The range of the Bluetooth system can be up to 30 ft 9 1
324. or write down the driver s name the service s name and the phone number Remove any valuables from your vehicle before it is towed away Make sure this includes your insurance information and registration if you keep these items in your vehicle e Gather the important information you will need from the other driver Things like name address phone number drivers license number vehicle license plate vehicle make model and model year Vehicle Identification Number VIN insurance company and policy number and a general description of the damage to the other vehicle e If possible call your insurance company from the scene of the crash They will walk you through the information they will need If they ask for a police report phone or go to the police department headquarters the next day and you can get a copy of the report for a nominal fee In some states provinces with no fault insurance laws a report may not be necessary This is especially true if there are no injuries and both vehicles are driveable Choose a reputable collision repair facility for your vehicle Whether you select a dealer retailer or a private collision repair facility to fix the damage make sure you are comfortable with them Remember you will have to feel comfortable with their work for a long time Once you have an estimate read it carefully and make sure you understand what work will be performed on your vehicle I
325. or might begin programs to inspect the emission control equipment on the vehicle Failure to pass this inspection could prevent getting a vehicle registration Here are some things to know to help the vehicle pass an inspection e The vehicle will not pass this inspection if the check engine light is on with the engine running or if the key is in ON RUN and the light is not on e The vehicle will not pass this inspection if the OBD II on board diagnostic system determines that critical emission control systems have not been completely diagnosed by the system The vehicle would be considered not ready for inspection This can happen if the battery has recently been replaced or if the battery has run down The diagnostic system is designed to evaluate critical emission control systems during normal driving This can take several days of routine driving If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness your dealer retailer can prepare the vehicle for inspection Oil Pressure Light Z CAUTION Do not keep driving if the oil pressure is low The engine can become so hot that it catches fire Someone could be burned Check the oil as soon as possible and have the vehicle serviced Instrument Panel 3 37 Notice Lack of proper engine oil maintenance can damage the engine The repairs would not be covered by the vehicle warranty Alwa
326. ormation Online Owner Center Online Owner Center U S www gmownercenter com saturn Information and services customized for your specific vehicle all in one convenient place e Digital owner manual warranty information and more e Online service and maintenance records e Find Saturn retailers for service nationwide e Exclusive privileges and offers e Recall notices for your specific vehicle OnStar and GM Cardmember Services Earnings summaries Other Helpful Links Saturn www saturn com Saturn Merchandise www saturncollection com Help Center www saturn com helpcenter e FAQ e Contact Us My GM Canada Canada www gm ca My GM Canada is a password protected section of www gm ca where you can save information on GM vehicles get personalized offers and use handy tools and forms with greater ease Here are a few of the valuable tools and services you will have access to My Showroom Find and save information on vehicles and current offers in your area My Dealers Retailers Save details such as address and phone number for each of your preferred GM dealers retailers My Driveway Access quick links to parts and service estimates check trade in values or schedule a service appointment by adding the vehicles you own to your driveway profile My Preferences Manage your profile and use tools and forms with greater ease To sign up visit the My GM Can
327. owing items e Make sure the fuel cap is fully installed See Filling the Tank on page 5 8 The diagnostic system can determine if the fuel cap has been left off or improperly installed A loose or missing fuel cap allows fuel to evaporate into the atmosphere A few driving trips with the cap properly installed should turn the light off e Ifthe vehicle has been driven through a deep puddle of water the vehicle s electrical system might be wet The condition is usually corrected when the electrical system dries out A few driving trips should turn the light off e Make sure to fuel the vehicle with quality fuel Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start up stalling when the vehicle is changed into gear misfiring hesitation on acceleration or stumbling on acceleration These conditions might go away once the engine is warmed up If one or more of these conditions occurs change the fuel brand used It will require at least one full tank of the proper fuel to turn the light off See Gasoline Octane on page 5 5 If none of the above have made the light turn off your dealer retailer can check the vehicle The dealer retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed Emissions Inspection and Maintenance Programs Some state provincial and local governments have
328. page 3 28 Glove Box on page 2 41 Instrument Panel 3 5 Hazard Warning Flashers A Hazard Warning Flasher Press this button located on the instrument panel to make the front and rear turn signal lamps flash on and off This warns others that you are having trouble Press A again to turn the flashers off Horn Press near or on the horn symbols on the steering wheel pad to sound the horn 3 6 Instrument Panel Tilt Wheel The tilt lever lets the steering wheel be adjusted The tilt lever is located on the left side of the steering column To adjust the steering wheel hold the wheel and push the lever down Then move the wheel to a comfortable position and pull the lever up firmly to lock the steering column in place Turn Signal Multifunction Lever The lever on the left side of the steering column includes Turn and Lane Change Signals D Headlamp High Low Beam Changer Flash to Pass Feature Information for these features is on the pages following Turn and Lane Change Signals gt An arrow on the instrument panel cluster flashes in the direction of the turn or lane change Move the lever all the way up or down to signal a turn Raise or lower the lever until the arrow starts to flash and then release to signal a lane change The turn signal flashes automatically three times The lever returns to its starting position whenever it is released If after s
329. parking brake If torque lock does occur you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission so you can pull the shift lever out of P Park Shifting Out of Park The vehicle has an electronic shift lock release system The shift lock release is designed to e Prevent ignition key removal unless the shift lever is in P Park with the shift lever button fully released e Prevent movement of the shift lever out of P Park unless the ignition is in ON RUN and the regular brake pedal is applied The shift lock release is always functional except in the case of an uncharged or low voltage less than 9 volt battery If the vehicle has an uncharged battery or a battery with low voltage try charging or jump starting the battery See Jump Starting on page 5 31 for more information To shift out of P Park 1 Apply the brake pedal 2 Press the shift lever button 3 Move the shift lever to the desired position If you still are unable to shift out of P Park 1 Fully release the shift lever button 2 Hold the brake pedal down and press the shift lever button again 3 Move the shift lever to the desired position If you still cannot move the shift lever from P Park consult your dealer retailer or a professional towing service Features and Controls 2 27 Parking Over Things That Burn Z CAUTIO
330. pearance Care 5 43 Z CAUTION CAUTION Continued Poorly maintained and improperly used tires are dangerous Overloading your tires can cause overheating as a result of too much flexing You could have an air out and a serious accident See Loading the Vehicle on page 4 28 Underinflated tires pose the same danger as overloaded tires The resulting accident could cause serious injury Check all tires frequently to maintain the recommended pressure Tire pressure should be checked when your tires are cold See Inflation Tire Pressure on page 5 49 Continued e Overinflated tires are more likely to be cut punctured or broken by a sudden impact such as when you hit a pothole Keep tires at the recommended pressure Worn old tires can cause accidents If your tread is badly worn or if your tires have been damaged replace them See High Speed Operation on page 5 50 for inflation pressure adjustment for high speed driving 5 44 Tire Sidewall Labeling Useful information about a tire is molded into its sidewall The examples below show a typical passenger vehicle tire and a compact spare tire sidewall 8 ae a A as eee uf aig SE Passenger P Metric Tire Example A Tire Size The tire size is a combination of letters and numbers used to define a particular tire s width height aspect ratio construction type and service description
331. pearance Care 5 7 However E85 85 ethanol and other fuels containing more than 10 ethanol must not be used in vehicles that were not designed for those fuels Notice This vehicle was not designed for fuel that contains methanol Do not use fuel containing methanol It can corrode metal parts in the fuel system and also damage plastic and rubber parts That damage would not be covered under the vehicle warranty Some gasolines that are not reformulated for low emissions can contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl MMT ask the attendant where you buy gasoline whether the fuel contains MMT We recommend against the use of such gasolines Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system could be affected The malfunction indicator lamp might turn on If this occurs return to your dealer retailer for service 5 8 Service and Appearance Care Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada the proper fuel might be hard to find Never use leaded gasoline or any other fuel not recommended in the previous text on fuel Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty To check the fuel availability ask an auto club or contact a major oil company that does business in the country where you will be driving
332. peats with every ignition cycle See Tire Pressure Monitor System on page 5 51 for more information Malfunction Indicator Lamp Check Engine Light A computer system called OBD II On Board Diagnostics Second Generation monitors operation of the fuel ignition and emission control systems It ensures that emissions are at acceptable levels for the life of the vehicle helping to produce a cleaner environment KI This light comes on when the ignition is on but the engine is not running as a check to show it is working If it does not have the vehicle serviced by your dealer retailer If the check engine light comes on and stays on while the engine is running this indicates that there is an OBD II problem and service is required Malfunctions often are indicated by the system before any problem is apparent Being aware of the light can prevent more serious damage to the vehicle This system assists the service technician in correctly diagnosing any malfunction Notice If the vehicle is continually driven with this light on after a while the emission controls might not work as well the vehicle s fuel economy might not be as good and the engine might not run as smoothly This could lead to costly repairs that might not be covered by the vehicle warranty Instrument Panel 3 35 Notice Modifications made to the engine transmission exhaust intake or fuel system of the vehicle or the repl
333. pecifications Notice Improperly tightened wheel nuts can lead to brake pulsation and rotor damage To avoid expensive brake repairs evenly tighten the wheel nuts in the proper sequence and to the proper torque specification See Capacities and Specifications on page 5 86 for the wheel nut torque specification 5 69 14 Lower the jack all the way and remove the jack from under the vehicle 15 Tighten the bolts firmly with the wheel wrench When reinstalling full plastic covers or center caps tighten all the plastic caps hand snug then tighten with the wheel wrench an additional one quarter of a turn Notice Wheel covers will not fit on your vehicle s compact spare If you try to put a wheel cover on the compact spare the cover or the spare could be damaged 5 70 Service and Appearance Care Storing a Flat or Spare Tire and Tools Z CAUTION Storing a jack a tire or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store all these in the proper place To store the flat or spare tire and tools do the following 1 Place the wheel wrench into the bag and use the straps to secure the bag to the fully collapsed jack 2 Install the jack between the back of the trunk and the compact spare tire and secure with the wing bolt Reverse Steps 1 through 3 under R
334. peed rating of the tire The load index represents the load carry capacity a tire is certified to carry The speed rating is the maximum speed a tire is certified to carry a load Tire Terminology and Definitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire Air pressure is expressed in pounds per square inch psi or kilopascal kPa Accessory Weight This means the combined weight of optional accessories Some examples of optional accessories are automatic transmission power steering power brakes power windows power seats and air conditioning Aspect Ratio The relationship of a tire s height to its width Belt A rubber coated layer of cords that is located between the plies and the tread Cords may be made from steel or other reinforcing materials Bead The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim Bias Ply Tire A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread Cold Tire Pressure The amount of air pressure in a tire measured in pounds per square inch psi or kilopascals kPa before a tire has built up heat from driving See nflation Tire Pressure on page 5 49 Curb Weight The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel oil and coolant but without passengers a
335. penses may be reimbursed during the 5 years 100 000 miles 160 000 km Powertrain warranty period Items considered are hotel meals and rental car Services Not Included in Roadside Assistance Impound towing caused by violation of any laws Legal fines Mounting dismounting or changing of snow tires chains or other traction devices Towing or services for vehicles driven on a non public road or highway 7 8 Services Specific to Canadian Purchased Vehicles Fuel delivery Reimbursement is approximately 5 Canadian Diesel fuel delivery may be restricted Propane and other fuels are not provided through this service Lock Out Service Vehicle registration is required Trip Routing Service Detailed maps of North America are provided when requested either with the most direct route or the most scenic route There is a limit of six requests per year Additional travel information is also available Allow three weeks for delivery Customer Assistance Information e Trip Interruption Benefits and Assistance Must be over 250 kilometres from where your trip was started to qualify General Motors of Canada Limited requires pre authorization original detailed receipts anda copy of the repair orders Once authorization has been received the Roadside Assistance advisor will help you make arrangements and explain how to receive payment Alternative Service If assistance cannot be provided righ
336. pidly You could lose control and hit people or objects Do not shift into a drive gear while the engine is running at high speed Notice Shifting out of P Park or N Neutral with the engine running at high speed may damage the transmission The repairs would not be covered by the vehicle warranty Be sure the engine is not running at high speed when shifting the vehicle D Drive This position is for normal driving with the automatic transmission It provides the best fuel economy If you need more power for passing and you are e Going less than about 35 mph 55 km h push the accelerator pedal about halfway down e Going about 35 mph 55 km h push the accelerator all the way down Features and Controls 2 23 Downshifting the transmission in slippery road conditions could result in skidding see Skidding under Loss of Control on page 4 12 M Manual This position allows you to change gears similar to a manual transmission If the vehicle has this feature see Manual Shift Mode Notice Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission The repair will not be covered by the vehicle warranty If you are stuck do not spin the tires When stopping on a hill use the brakes to hold the vehicle in place 2 24 Manual Shift Mode MSM Automatic Transmission To use this feature do the following
337. plate to fully tighten the lap belt on smaller occupants Seats and Restraint System To unlatch the belt push the button on the buckle The belt should return to its stowed position Slide the latch plate up the safety belt webbing when the safety belt is not in use The latch plate should rest on the stitching on the safety belt near the guide loop on the side wall Before a door is closed be sure the safety belt is out of the way If a door is slammed against a safety belt damage can occur to both the safety belt and the vehicle Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions Adjust the height so that the shoulder portion of the belt is centered on the shoulder The belt should be away from the face and neck but not falling off of the shoulder Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt ina crash Squeeze the release buttons A together and move the height adjuster up or down to the desired position After the adjuster is set to the desired position try to move it up or down without squeezing the release buttons to make sure it has locked into position Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants Although the safety belt pretensioners cannot be seen they Seats and Restraint System are part
338. porary Use Only The compact spare tire or temporary use tire has a tread life of approximately 3 000 miles 5 000 km and should not be driven at speeds over 65 mph 105 km h The compact spare tire is for emergency use when a regular road tire has lost air and gone flat If your vehicle has a compact spare tire see Compact Spare Tire on page 5 71 and Ifa Tire Goes Flat on page 5 63 Service and Appearance Care B Tire Ply Material The type of cord and number of plies in the sidewall and under the tread C Tire Identification Number TIN The letters and numbers following the DOT Department of Transportation code is the Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of the tire although only one side may have the date of manufacture D Maximum Cold Inflation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load E Tire Inflation The temporary use tire or compact spare tire should be inflated to 60 psi 420 kPa For more information on tire pressure and inflation see Inflation Tire Pressure on page 5 49 5 45 F Tire Size A combination of letters and numbers define a tire s width height aspect ratio construction type and service description The letter T as the first character in the tire size means the tire is for temporary
339. pray from all painted surfaces on the vehicle 5 78 Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement make sure the body repair shop applies anti corrosion material to parts repaired or replaced to restore corrosion protection Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty Finish Damage Any stone chips fractures or deep scratches in the finish should be repaired right away Bare metal will corrode quickly and may develop into major repair expense Minor chips and scratches can be repaired with touch up materials available from your dealer retailer Larger areas of finish damage can be corrected in your dealer s retailer s body and paint shop Service and Appearance Care Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody If these are not removed corrosion and rust can develop on the underbody parts such as fuel lines frame floor pan and exhaust system even though they have corrosion protection At least every spring flush these materials from the underbody with plain water Clean any areas where mud and debris can collect Dirt packed in close areas of the frame should be loosened before being flushed Your dealer retailer or an underbody car washing system can do this Chemical Paint Spotting Some weather and atmosphe
340. ps 9005 or HB3 9006 or HB4 3057 For replacement bulbs not listed here contact your dealer retailer High beam Low beam DRL Rear Turn Signal Stoplamp and Taillamp 5 42 Service and Appearance Care Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking See Scheduled Maintenance on page 6 3 for more information Replacement blades come in different types and are removed in different ways For proper type and length see Maintenance Replacement Parts on page 6 15 To replace the windshield wiper blade 1 Lift the wiper arm away from the windshield as L _ pie O 2 Push the release lever B to disengage the hook and push the wiper arm A out of the blade C 3 Push the new wiper blade securely on the wiper arm until you hear the release lever click into place To replace the rear wiper blade e 1 Lift the rear wiper arm A from the window 2 Rotate the bottom edge of the blade assembly B slightly away from the underside of the wiper arm 3 Apply downward pressure to the blade assembly and remove from the wiper arm Tires Your new vehicle comes with high quality tires made by a leading tire manufacturer If you ever have questions about your tire warranty and where to obtain service see your vehicle Warranty booklet for details For additional information refer to the tire manufacturer Service and Ap
341. r If the tailpipe is under water you will never be able to start the engine When going through water remember that when the brakes get wet it might take longer to stop See Driving in Rain and on Wet Roads on page 4 23 After Off Road Driving Remove any brush or debris that has collected on the underbody chassis or under the hood These accumulations can be a fire hazard After operation in mud or sand have the brake linings cleaned and checked These substances can cause glazing and uneven braking Check the body structure steering suspension wheels tires axles and exhaust system for damage and check the fuel lines and cooling system for any leakage The vehicle requires more frequent service due to off road use Refer to the Maintenance Schedule for additional information Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired by alcohol or drugs with night vision problems or by fatigue Night driving tips include e Drive defensively e Do not drink and drive e Reduce headlamp glare by adjusting the inside rearview mirror e Slow down and keep more space between you and other vehicles because headlamps can only light up So much road ahead e Watch for animals e When tired pull off the road e Do not wear sunglasses e Avoid staring directly into approaching headlamps e Keep the windshield and all glass on your vehicle
342. r down the hill so you will not have to make turning maneuvers e Are there obstructions on the hill that can block your path such as boulders trees logs or ruts e What is beyond the hill Is there a cliff an embankment a drop off a fence Get out and walk the hill if you do not know It is the smart way to find out e Is the hill simply too rough Steep hills often have ruts gullies troughs and exposed rocks because they are more susceptible to the effects of erosion 4 18 Driving Your Vehicle Driving Uphill Once you decide it is safe to drive up the hill Use a low gear and get a firm grip on the steering wheel Get a smooth start up the hill and try to maintain speed Not using more power than needed can avoid spinning the wheels or sliding Z CAUTION Ease up on the speed as you approach the top of the hill Attach a flag to the vehicle to be more visible to approaching traffic on trails or hills Sound the horn as you approach the top of the hill to let opposing traffic know you are there Use headlamps even during the day to make the vehicle more visible to oncoming traffic If the vehicle stalls or is about to stall and you cannot make it up the hill Turning or driving across steep hills can be dangerous You could lose traction slide sideways and possibly roll over You could be seriously injured or killed When driving up hills always try to go straight up
343. r dealer retailer If an abnormal temperature reading is displayed for an extended period of time consult your dealer retailer Under certain circumstances especially when the engine is idling a delay updating the temperature display is normal See DIC Compass on page 3 47 and Automatic Transmission Operation Uplevel on page 2 19 or Automatic Transmission Operation Base on page 2 22 for more information DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel below the headlamp switch The DIC displays trip fuel and vehicle system information and warning messages if a system problem is detected The DIC also allows some features to be customized See DIC Vehicle Customization on page 3 57 for more information 3 43 Instrument Panel DIC Buttons of ei Ee ff The buttons are the trip fuel vehicle information customization and set reset buttons The button functions are detailed in the following pages ZN Trip Fuel Press this button to display the odometer trip odometer fuel range average economy fuel used and elapsed time Some vehicles also display instantaneous economy The compass and outside temperature will also be shown in the display The temperature will be shown in F or C depending on the units selected i Vehicle Information Press this button to display the oil life units t
344. r dealer retailer will order you an extender When you go in to order it take the heaviest coat you will wear so the extender will be long enough for you To help avoid personal injury do not let someone else use it and use it only for the seat it is made to fit The extender has been designed for adults Never use it for securing child seats To wear it attach it to the regular safety belt For more information see the instruction sheet that comes with the extender 1 23 Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle s safety belts 1 24 The manufacturer s instructions that come with the booster seat state the weight and height limitations for that booster Use a booster seat with a lap shoulder belt until the child passes the below fit test e Sit all the way back on the seat Do the knees bend at the seat edge If yes continue If no return to the booster seat e Buckle the lap shoulder belt Does the shoulder belt rest on the shoulder If yes continue If no try using the rear safety belt comfort guide See Rear Safety Belt Comfort Guides under Lap Shoulder Belt on page 1 19 for more information If the shoulder belt still does not rest on the shoulder then return to the booster seat e Does the lap belt fit low and snug on the hips touching the thighs If yes continue If no return to the booster seat Seats and Res
345. r retailer will set the correct zone for your location Under certain circumstances such as during a long distance cross country trip or moving to a new state or province it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly Compass variance is the difference between the earth s magnetic north and true geographic north If the compass is not set to the zone where you live the compass may give false readings The compass must be set to the variance zone in which the vehicle is traveling 3 48 Instrument Panel To adjust for compass variance use the following procedure Compass Variance Zone Procedure 1 Do not set the compass zone when the vehicle is moving Only set it when the vehicle is in P Park Press the vehicle information button until PRESS vV TO SET COMPASS ZONE displays 2 Find the vehicle s current location and variance zone number on the map Zones 1 through 15 are available 3 Press and hold the set reset button to scroll through and select the appropriate variance zone 4 Press the trip fuel button until the vehicle heading for example N for North is displayed in the DIC 5 If calibration is necessary calibrate the compass See Compass Calibration Procedure following Compass Calibration The compass can be manually calibrated Only calibrate the compass in a magnetically clean a
346. r scooter lifts etc The offer is available for a limited period of time from the date of vehicle purchase lease For more details or to determine your vehicle s eligibility visit your Saturn retailer or call the Saturn Customer Assistance Center at 1 800 553 6000 Text telephone TTY users call 1 800 833 6000 In Canada customers may call the Saturn Customer Communication Centre at 1 800 263 1999 TTY users in Canada may call 1 800 263 3830 Roadside Assistance Program For U S purchased vehicles call 1 800 553 6000 Text Telephone TTY 1 800 889 2438 For Canadian purchased vehicles call 1 800 268 6800 Service is available 24 hours a day 365 days a year Calling for Assistance When calling Roadside Assistance have the following information ready e Your name home address and home telephone number Telephone number of your location e Location of the vehicle e Model year color and license plate number of the vehicle e Odometer reading Vehicle Identification Number VIN and delivery date of the vehicle e Description of the problem Coverage Services are provided up to 5 years 100 000 miles 160 000 km whichever comes first In the U S anyone driving the vehicle is covered In Canada a person driving the vehicle without permission from the owner is not covered Roadside Assistance is not a part of the New Vehicle Limited Warranty Saturn and General Moto
347. r several seconds as a system check Then after several more seconds the status indicator will light either ON or OFF or either the on or off symbol to let you know the status of the right front passenger frontal and seat mounted side impact airbags If the word ON or the on symbol is lit on the passenger airbag status indicator it means that the right front passenger frontal airbag and seat mounted side impact airbag are enabled may inflate If the word OFF or the off symbol is lit on the airbag status indicator it means that the passenger sensing system has turned off the right front passenger frontal airbag and seat mounted side impact airbag If after several seconds both status indicator lights remain on or if there are no lights at all there may be a problem with the lights or the passenger sensing system See your dealer retailer for service Z CAUTION If the airbag readiness light ever comes on and stays on it means that something may be wrong with the airbag system To help avoid injury to yourself or others have the vehicle serviced right away See Airbag Readiness Light on page 3 29 for more information including important safety information Charging System Light The charging system light comes on briefly when the ignition is turned on but the engine is not running as a check to show the light is working It should go out when the engine is started If the light stay
348. raint Replacing Restraint System Parts After a Crash 1 1 1 2 Seats and Restraint System Head Restraints The front and rear seats have adjustable head restraints in the outboard seating positions Z CAUTION With head restraints that are not installed and adjusted properly there is a greater chance that occupants will suffer a neck spinal injury in a crash Do not drive until the head restraints for all occupants are installed and adjusted properly Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant s head This position reduces the chance of a neck injury in a crash Pull the head restraint up to raise it To lower the head restraint press the button located on the top of the seatback and push the restraint down Seats and Restraint System 1 3 Push down on the head restraint after the button is released to make sure that it is locked in place The head restraints are not designed to be removed Active Head Restraint System The vehicle has an active head restraint system in the front outboard seating positions The active head restraints automatically tilt forward to reduce the risk of neck injury if the vehicle is hit from behind Front Seats Manual Seats Z CAUTION You can lose control of the vehicle if you try to adjust a manual driver s seat while the vehicle is moving The sudden movement
349. receiving specific information from these stations and only works when the information is available While the radio is tuned to an FM RDS station the station name or call letters displays In rare cases a radio station can broadcast incorrect Instrument Panel 3 67 information that causes the radio features to work improperly If this happens contact the radio station Playing the Radio D Power Volume Press to turn the system on and off Turn to increase or decrease the volume Finding a Station BAND Press to switch between AM FM or XM if equipped J Tune Turn to select radio stations Ki SEEK I Press to go to the previous or to the next station To scan stations press and hold either arrow for a few seconds until a beep sounds The radio goes to a station plays for a few seconds then goes to the next station Press either arrow again to stop scanning 3 68 Instrument Panel The radio only seeks and scans stations with a strong signal that are in the selected band i Information XM Satellite Radio Service MP3 and RDS Features Press to display additional text information related to the current FM RDS station XM station or MP3 song If information is available the song title information displays on the top line of the display and artist information displays on the bottom line When information is not available NO INFO displays Storing a Radio Station as
350. reezing use a fluid that has sufficient protection against freezing Adding Windshield Washer Fluid Open the cap with the washer symbol on it Add washer fluid until the tank is full See Engine Compartment Overview on page 5 12 for reservoir location 5 27 Notice e When using concentrated washer fluid follow the manufacturer s instructions for adding water Do not mix water with ready to use washer fluid Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system Also water does not clean as well as washer fluid Fill the washer fluid tank only three quarters full when it is very cold This allows for fluid expansion if freezing occurs which could damage the tank if it is completely full e Do not use engine coolant antifreeze in your windshield washer It can damage the vehicle s windshield washer system and paint 5 28 Service and Appearance Care Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid See Engine Compartment Overview on page 5 12 for the location of the reservoir There are only two reasons why the brake fluid level in the reservoir might go down e The brake fluid level goes down because of normal brake lining wear When new linings are installed the fluid level goes back up e A fluid leak in the brake hydraulic system can also cause a low fluid level Have the br
351. rence that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System TPMS The TPMS is designed to warn the driver when a low tire pressure condition exists TPMS sensors are mounted onto each tire and wheel assembly excluding the spare tire and wheel assembly The TPMS sensors monitor the air pressure in the vehicle s tires and transmit the tire pressure readings to a receiver located in the vehicle 1 When a low tire pressure condition is detected the TPMS illuminates the low tire pressure warning light on the instrument panel cluster Service and Appearance Care The low tire pressure warning light comes on at each ignition cycle until the tires are inflated to the correct inflation pressure The low tire pressure warning light may come on in cool weather when the vehicle is first started and then turn off as you start to drive This may be an early indicator that the air pressure in the tire s are getting low and need to be inflated to the proper pressure A Tire and Loading Information label attached to your vehicle shows the size of your vehicle s original equipment tires and the correct inflation pressure for your vehicle s tires when they are cold See Loading the Vehicle on page 4
352. revent a stall by shifting into N Neutral to rev up the engine and regain forward momentum This will not work The vehicle can roll backward very quickly and could go out of control Never try to turn around if about to stall when going up a hill If the hill is steep enough to stall the vehicle it is steep enough to cause it to roll over If you cannot make it up the hill back straight down the hill If after stalling you try to back down the hill and decide you just cannot do it set the parking brake put your transmission in P Park and turn off the engine Leave the vehicle and go get some help Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill Driving Downhill When off roading takes you downhill consider e How steep is the downhill Will be able to maintain vehicle control e What is the surface like Smooth Rough Slippery Hard packed dirt Gravel e Are there hidden surface obstacles Ruts Logs Boulders e What is at the bottom of the hill Is there a hidden creek bank or even a river bottom with large rocks Driving Your Vehicle 4 19 If you decide you can go down a hill safely try to keep the vehicle headed straight down Use a low gear so engine drag can help the brakes so they do not have to do all the work Descend slowly keeping the vehicle under control at all times Z CAUTION Heavy braking when going down a hill
353. ric conditions can create a chemical fallout Airborne pollutants can fall upon and attack painted surfaces on the vehicle This damage can take two forms blotchy ring shaped discolorations and small irregular dark spots etched into the paint surface Although no defect in the paint job causes this we will repair at no charge to the owner the surfaces of new vehicles damaged by this fallout condition within 12 months or 12 000 miles 20 000 km of purchase whichever occurs first Vehicle Identification Vehicle Identification Number VIN SAMPLE4UX1Mo72675 F e This is the legal identifier for the vehicle It appears on a plate in the front corner of the instrument panel on the driver side It can be seen through the windshield from outside the vehicle The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration Engine Identification The eighth character in the VIN is the engine code This code helps identify the vehicle s engine specifications and replacement parts See Engine Specifications under Capacities and Specifications on page 5 86 for the vehicle s engine code Service and Appearance Care Service Parts Identification Label This label is on the inside of the glove box It is very helpful if parts need to be ordered The label has the following information e Vehicle Identification Number VIN Mode
354. ric brakes start the vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working This checks the electrical connection at the same time During the trip check occasionally to be sure that the load is secure and that the lamps and any trailer brakes are still working Driving Your Vehicle 4 41 Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer This can help to avoid situations that require heavy braking and sudden turns Passing More passing distance is needed when towing a trailer Because the rig is longer it is necessary to go much farther beyond the passed vehicle before returning to the lane Backing Up Hold the bottom of the steering wheel with one hand Then to move the trailer to the left move that hand to the left To move the trailer to the right move your hand to the right Always back up slowly and if possible have someone guide you 4 42 Making Turns Notice Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle The vehicle could be damaged Avoid making very sharp turns while trailering When turning with a trailer make wider turns than normal Do this so the trailer will not strike soft shoulders curbs road signs trees or other objects Avoid jerky or sudden maneuvers Signal well in advance Tur
355. rs of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification Saturn and General Motors of Canada Limited reserve the right to limit services or payment to an owner or driver if they decide the claims are made too often or the same type of claim is made many times Services Provided e Emergency Fuel Delivery Delivery of enough fuel for the vehicle to get to the nearest service station e Lock Out Service Service is provided to unlock the vehicle if you are locked out A remote unlock may be available if you have OnStar For security reasons the driver must present identification before this service is given Customer Assistance Information 7 7 Emergency Tow From a Public Road or Highway Tow to the nearest Saturn retailer for warranty service or if the vehicle was in a crash and cannot be driven Assistance is also given when the vehicle is stuck in sand mud or snow Flat Tire Change Service is provided to change a flat tire with the spare tire The spare tire if equipped must be in good condition and properly inflated It is the owner s responsibility for the repair or replacement of the tire if it is not covered by the warranty Battery Jump Start Service is provided to jump start a dead battery Trip Interruption Benefits and Assistance If your trip is interrupted due to a warranty failure incidental ex
356. rtesy Transportation 7 9 Collision Damage Repair 7 10 Customer Assistance Information 7 1 Reporting Safety Defects Reporting Safety Defects to the United States Government eeeceeeeeeee eee 7 14 Reporting Safety Defects to the Canadian Government 7 14 Reporting Safety Defects tO Saturn cccceceeeeseceaeeeee ees 7 14 Service Publications Ordering Information 7 15 Vehicle Data Recording and Privacy Vehicle Data Recording and PrVaCy sesierririnisseai aret 7 16 Event Data Recorders 7 16 OnStar weccsccvencscswniatiuaseenes 7 17 Navigation System 7 17 Radio Frequency Identification RFID 7 17 Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn Together we are committed to providing our customers with unparalleled service before during and after the purchase of a Saturn vehicle for total customer satisfaction We call this the Saturn Difference Normally any concerns with the sales transaction or the operation of the vehicle are resolved by the retailers sales or service departments If for any reason your ownership experience falls below your expectations we suggest you take the following action STEP ONE Contact the Retail Customer Assistance Liaison Any member of the retail management team has the authority and the desire to res
357. ructions Ina remote area a winch can be handy if you get stuck but you will want to know how to use it properly Getting Familiar with Off Road Driving It is a good idea to practice in an area that is safe and close to home before you go into the wilderness Off roading requires some new and different skills Tune your senses to different kinds of signals Your eyes need to constantly sweep the terrain for unexpected obstacles Your ears need to listen for unusual tire or engine sounds Use your arms hands feet and body to respond to vibrations and vehicle bounce Driving Your Vehicle 4 15 Controlling the vehicle is the key to successful off road driving One of the best ways to control the vehicle is to control the speed At higher speeds e You approach things faster and have less time to react e There is less time to scan the terrain for obstacles e The vehicle has more bounce when driving over obstacles e More braking distance is needed especially on an unpaved surface Z CAUTION When you are driving off road bouncing and quick changes in direction can easily throw you out of position This could cause you to lose control and crash So whether you are driving on or off the road you and your passengers should wear safety belts 4 16 Scanning the Terrain Off road driving can take you over many different kinds of terrain Be familiar with the terrain and its many dif
358. ry LB or GC LB Automatic Transmission DEXRON VI Automatic Transmission Fluid 6 14 Maintenance Schedule Usage i O Fluid Lubricant Transfer Case and Carrier SAE 75W 90 Synthetic Axle Lubricant GM Part No U S 89021677 Assembly Differential in Canada 89021678 meeting GM Specification 9986115 Multi Purpose Lubricant Superlube GM Part No U S 12346241 Key Lock Cylinders in Canada 10953474 Hood Latch Assembly Secondary Lubriplate Lubricant Aerosol Saturn Part No 21038869 or Latch Pivots Spring Anchor and GM Part No U S 12346293 in Canada 992723 or lubricant Release Pawl meeting requirements of NLGI 2 Category LB or GC LB Hood Liftgate Door and Rear Multi Purpose Lubricant Superlube GM Part No U S 12346241 Folding Seat Hinges in Canada 10953474 Lubriplate Lubricant Aerosol Saturn Part No 21038869 or Sunroof Track GM Part No U S 12346293 in Canada 992723 or lubricant meeting requirements of NLGI 2 Category LB or GC LB Weatherstrip Lubricant GM Part No U S 3634770 Weatherstrip Conditioning in Canada 10953518 or Dielectric Silicone Grease GM Part No U S 12345579 in Canada 992887 Maintenance Schedule 6 15 Maintenance Replacement Parts Replacement parts identified below by name part number or specification can be obtained from your retailer at ai Part Number ACDelco Part Number rEngine Ar GleaneFiter O O O OO e O o PFASTG PFI Pras Driver Side 24 in 60 0 o
359. s A chime will sound indicating that the transmitter is matched and REMOTE KEY LEARNING COMPLETE will be shown on the display 4 To match additional transmitters at this time repeat Step 3 Each vehicle can have a maximum of eight transmitters matched to it 5 To exit the programming mode you must cycle the key to LOCK OFF Compass Zone Setting This display allows for setting the compass zone See DIC Compass on page 3 47 for more information Compass Recalibration This display allows for calibrating the compass See DIC Compass on page 3 47 for more information Coolant Temperature Press the vehicle info button until the coolant temperature is displayed The temperature will be shown in F or C depending on the units selected If the coolant temperature display shows dashes instead of a value there may be a problem with the vehicle If this happens often see your dealer retailer for service Battery Voltage Press the vehicle info button until the battery voltage is displayed If the battery voltage display shows dashes instead of a value there may be a problem with the vehicle If this happens often see your dealer retailer for service Blank Display This display shows no information Instrument Panel 3 47 DIC Compass Your vehicle may have a compass in the Driver Information Center DIC Compass Zone The zone is set to zone eight upon leaving the factory Your deale
360. s Brake Pedal Travel See your dealer retailer if the brake pedal does not return to normal height or if there is a rapid increase in pedal travel This could be a sign that brake service might be required Brake Adjustment Every time the brakes are applied with or without the vehicle moving the brakes adjust for wear 5 30 Replacing Brake System Parts The braking system on a vehicle is complex Its many parts have to be of top quality and work well together if the vehicle is to have really good braking The vehicle was designed and tested with top quality brake parts When parts of the braking system are replaced for example when the brake linings wear down and new ones are installed be sure to get new approved replacement parts If this is not done the brakes might not work properly For example if someone puts in brake linings that are wrong for the vehicle the balance between the front and rear brakes can change for the worse The braking performance expected can change in many other ways if the wrong replacement brake parts are installed Service and Appearance Care Battery This vehicle has a maintenance free battery When it is time for a new battery see your dealer retailer for one that has the replacement number shown on the original battery s label See Engine Compartment Overview on page 5 12 for battery location Warning Battery posts terminals and related accessories
361. s until the number to be stored is complete e If an unwanted number is recognized by the system say Clear at any time to clear the last number e To hear all of the numbers recognized by the system say Verify at any time and the system will repeat them 4 After the complete number has been entered say Store The system responds with Please say the name tag followed by a tone Say a name tag for the phone number The name tag is recorded and the system responds with About to store lt name tag gt Does that sound OK e Ifthe name tag does not sound correct say No and repeat Step 5 e Ifthe name tag sounds correct say Yes and the name tag is stored After the number is stored the system returns to the main menu Using the Directory Command The directory command lists all of the name tags stored by the system To use the directory command 1 Press and hold for two seconds The system responds with Ready followed by a tone 2 Say Directory The system responds with Directory and then plays back all of the stored name tags When the list is complete the system returns to the main menu Deleting Name Tags The system uses the following commands to delete name tags e Delete e Delete all name tags Instrument Panel 3 85 Using the Delete Command The delete command allows specific name tags to be deleted To
362. s feature assists in starting the engine and protects components If the ignition key is turned to the START position and then released when the engine begins 2 17 cranking the engine will continue cranking for a few seconds or until the vehicle starts If the engine does not start and the key is held in START cranking will be stopped after 15 seconds to prevent cranking motor damage To prevent gear damage this system also prevents cranking if the engine is already running Engine cranking can be stopped by turning the ignition switch to the ACC ACCESSORY or LOCK OFF position Notice Cranking the engine for long periods of time by returning the key to the START position immediately after cranking has ended can overheat and damage the cranking motor and drain the battery Wait at least 15 seconds between each try to let the cranking motor cool down 2 18 2 If the engine does not start after 5 10 seconds especially in very cold weather below 0 F or 18 C it could be flooded with too much gasoline Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds Wait at least 15 seconds between each try to allow the cranking motor to cool down When the engine starts let go of the key and accelerator If the vehicle starts briefly but then stops again repeat these steps This clears the extra gasoline from the engine
363. s on or comes on while driving there could be a problem with the electrical charging system Have it checked by your dealer retailer Driving while this light is on could drain the battery If a short distance must be driven with the light on be sure to turn off all accessories such as the radio and air conditioner Instrument Panel 3 31 Brake System Warning o BRAKE United States The brake indicator light should come on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer When the ignition is on the brake system warning light comes on when the parking brake is set The light stays on if the parking brake does not fully release 3 32 Instrument Panel If it stays on after the parking brake is fully released there is a brake problem Have the brake system inspected immediately Z CAUTION The brake system might not be working properly if the brake system warning light is on Driving with the brake system warning light on can lead to a crash If the light is still on after the vehicle has been pulled off the road and carefully stopped have the vehicle towed for service If the light comes on while driving a chime sounds Pull off the road and stop The pedal might be harder to push or go closer to the floor It might also take longer to stop If the light is still on have the vehicle towed for service See Towing Your Vehic
364. s than 1 000 Ibs 454 kg to avoid exceeding GVWR But the effect on the rear axle must still be considered Because the rear axle now weighs 3 100 Ibs 1 406 kg 900 Ibs 408 kg can be put on the rear axle without exceeding RGAWR The effect of tongue weight is about 1 5 times the actual weight Dividing the 900 Ibs 408 kg by 1 5 leaves only 600 Ibs 272 kg of tongue weight that can be handled Since tongue weight is usually at least 10 percent of total loaded trailer weight expect that the largest trailer the vehicle can properly handle is 6 000 Ibs 2 721 kg Driving Your Vehicle 4 39 It is important that the vehicle does not exceed any of its ratings GCWR GVWR RGAWR Maximum Trailer Rating or Tongue Weight The only way to be sure it is not exceeding any of these ratings is to weigh the vehicle and trailer Total Weight on the Vehicle s Tires Be sure the vehicle s tires are inflated to the upper limit for cold tires These numbers can be found on the Certification label or see Loading the Vehicle on page 4 28 for more information Make sure not to go over the GVW limit for the vehicle or the GAWR including the weight of the trailer tongue 4 40 Hitches It is important to have the correct hitch equipment Crosswinds large trucks going by and rough roads are a few reasons why the right hitch is needed e The rear bumper on the vehicle is not intended for hitches Do not attach rent
365. s what kind of oil to use For engine oil crankcase capacity see Capacities and Specifications on page 5 86 Notice Do not add too much oil If the engine has so much oil that the oil level gets above the upper mark that shows the proper operating range the engine could be damaged T AAAA See Engine Compartment Overview on page 5 12 for the location of the engine oil fill cap Add enough oil to put the level somewhere in the proper operating range Push the dipstick all the way back in when through What Kind of Engine Oil to Use Look for three things RECOMMENDED SAE S1S006ITY GRADE ROT WEATHER BAE SW GOLD WEATHER Oo ROT LE GA ii AE BOWS OA ANY OTHER Scary GRADE CL WOT RECOMMEMOET Service and Appearance Care e GM6094M Use only an oil that meets GM Standard GM6094M e SAE 5W 30 SAE 5W 30 is best for the vehicle These numbers on an oil container show its viscosity or thickness Do not use other viscosity oils such as SAE 20W 50 e American Petroleum Institute API starburst symbol Oils meeting these requirements should have the starburst symbol on the container This symbol indicates that the oil has been certified by the American Petroleum Institute API 5 15 Notice Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol Failure to use the recommended oil can r
366. sabled For more information see All Wheel Drive AWD System on page 4 9 Gate Ajar Light a If the gate ajar light comes on the liftgate is not completely closed Driving with the liftgate open can cause carbon monoxide CO to enter the vehicle See Engine Exhaust on page 2 28 for more information Door Ajar Light a The door ajar light comes on when a door is open Before driving check that all doors are properly closed Service Vehicle Soon Light C m The service vehicle soon light comes on if a condition exists that may require the vehicle to be taken in for service If the light comes on take the vehicle to your dealer retailer for service as soon as possible Fuel Gage Canada United States When the ignition is on the fuel gage indicates how much fuel is left in the tank When the indicator nears empty the low fuel light comes on There is still a little fuel left but the fuel tank should be refilled soon See Low Fuel Warning Light on page 3 41 for more information An arrow on the fuel gage indicates the side of the vehicle the fuel door is on Here are four things that some owners ask about None of these means the fuel gage is not working properly e At the service station the fuel pump shuts off before the gage reads full e It takes a little more or less fuel to fill up than the gage indicated For example the gage may have indicated the tank was half full
367. safety belts Frontal airbags distribute the force of the impact more evenly over the occupant s upper body stopping the occupant more gradually Seat mounted side impact and roof rail airbags distribute the force of the impact more evenly over the occupant s upper body 1 49 Rollover capable roof rail airbags are designed to help contain the head and chest of occupants in the outboard seating positions in the first and second rows The rollover capable roof rail airbags are designed to help reduce the risk of full or partial ejection in rollover events although no system can prevent all such ejections But airbags would not help in many types of collisions primarily because the occupant s motion is not toward those airbags See When Should an Airbag Inflate on page 1 47 for more information Airbags should never be regarded as anything more than a supplement to safety belts 1 50 Seats and Restraint System What Will You See After an Airbag Inflates CAUTION After the frontal airbags and When an airbag inflates there seat mounted side impact airbags may be dust in the air This dust inflate they quickly deflate so could cause breathing problems quickly that some people may not for people with a history of even realize an airbag inflated asthma or other breathing trouble Roof rail airbags may still be at least To avoid this everyone in the partially inflated for some time vehicle sho
368. sary repairs done before you or anyone else drives the vehicle We recommend the use of genuine parts from your dealer retailer Scheduled Maintenance When the Change Engine Oil light displays service is required for the vehicle Have the vehicle serviced as soon as possible within the next 600 miles 1 000 km It is possible that if driving under the best conditions the engine oil life system may not indicate that vehicle service is necessary for over a year However the engine oil and filter must be changed at least once a year and at this time the system must be reset Your dealer retailer has trained service technicians who will perform this work using genuine parts and reset the system Maintenance Schedule 6 3 If the engine oil life system is ever reset accidentally service the vehicle within 3 000 miles 5 000 km since the last service Remember to reset the oil life system whenever the oil is changed See Engine Oil Life System on page 5 16 for information on the Engine Oil Life System and resetting the system When the Change Engine Oil light appears certain services checks and inspections are required Required services are described in the following for Maintenance I and Maintenance II Generally it is recommended that the first service be Maintenance I the second service be Maintenance II and then alternate Maintenance I and Maintenance II thereafter However in some cases M
369. se the device will time out and the procedure will have to be repeated To program up to three devices 1 From inside the vehicle press and hold down the two outside buttons at the same time releasing only when the Universal Home Remote indicator light begins to flash after 20 seconds This step will erase the factory settings or all previously programmed buttons Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons 2 Hold the end of your hand held transmitter about 1 to 3 inches 3 to 8 cm away from the Universal Home Remote buttons while keeping the indicator light in view The hand held transmitter was supplied by the manufacturer of your garage door opener receiver motor head unit 3 At the same time press and hold both the Universal Home Remote button to be used to control the garage door and the hand held transmitter button Do not release the Universal Home Remote button or the hand held transmitter button until Step 4 has been completed Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in Gate Operator and Canadian Programming later in this section Features and Controls 4 The indicator light on the Universal Home Remote will flash slowly at first and then rapidly after Universal Home Remote successfully receives the frequency signal from t
370. second skid if it occurs Of course traction is reduced when water snow ice gravel or other material is on the road For safety slow down and adjust your driving to these conditions It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited While driving on a surface with reduced traction try your best to avoid sudden steering acceleration or braking including reducing vehicle speed by shifting to a lower gear Any sudden changes could cause the tires to slide You may not realize the surface is slippery until the vehicle is skidding Learn to recognize warning clues such as enough water ice or packed snow on the road to make a mirrored surface and slow down when you have any doubt Remember Any Antilock Brake System ABS helps avoid only the braking skid Off Road Driving Vehicles with all wheel drive can be used for off road driving Vehicles without all wheel drive should not be driven off road except on a level solid surface Many of the vehicle design features that help make the vehicle more responsive on paved roads during poor weather conditions also help make it better suited for off road use than conventional passenger vehicles The vehicle does not have features usually thought to be necessary for extended or severe off road use such as special underbody shielding and transfer case low gear range The airbag syst
371. see Towing a Trailer on page 4 35 Make sure the shift lever is fully in P Park before starting the engine The vehicle has an automatic transmission shift lock control system You have to fully apply the regular brakes first and then press the shift lever button before you can shift from P Park when the ignition key is in ON RUN If you cannot shift out of P Park ease pressure on the shift lever and push the shift lever all the way into P Park as you maintain brake application Then press the shift lever button and move the shift lever into another gear See Shifting Out of Park on page 2 27 R Reverse Use this gear to back up Notice Shifting to R Reverse while the vehicle is moving forward could damage the transmission The repairs would not be covered by the vehicle warranty Shift to R Reverse only after the vehicle is stopped To rock the vehicle back and forth to get out of snow ice or sand without damaging the transmission see f Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 27 N Neutral In this position the engine does not connect with the wheels To restart the engine when the vehicle is already moving use N Neutral only Also use N Neutral when the vehicle is being towed Z CAUTION Shifting into a drive gear while the engine is running at high speed is dangerous Unless your foot is firmly on the brake pedal the vehicle could move very ra
372. set speed or to accelerate to a higher speed SET Set Coast Move the thumbwheel down to set a speed or to decrease the speed To set a speed 1 Press to turn cruise control on The indicator light on the button comes on 2 Get to the speed desired 3 Press the thumbwheel toward SET and release it 4 Take your foot off the accelerator pedal When the brakes are applied the cruise control shuts off Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied the cruise control is disengaged The indicator light on the instrument panel cluster goes out when the cruise is no longer engaged To return to the previously set speed press the thumbwheel up toward RES briefly when the vehicle has reached a speed of about 25 mph 40 km h or more This accelerates the vehicle to the previously selected speed Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control e Move the thumbwheel up toward RES and hold it until the vehicle accelerates to the desired speed and then release the switch e To increase the speed in small amounts move the thumbwheel up toward RES briefly and then release it Each time this is done the vehicle goes about 1 mph 1 6 km h faster e Use the accelerator pedal to reach the desired speed and move the thumbwheel towards SET The new desired speed must be greater than the pr
373. snzaccsanahonns Rocking Your Vehicle to Get it Out a an Roof SUNMOOT seis sadceexecedawecteacs Running the Vehicle While Parked iscAssatisticieeiteine Safety Belt Reminders Safety Belts Care of Extender How to Wear Safety Belts Properly INDEX i 9 Safety Belts cont Lap Shoulder Belt 1 19 Safety Belts Are for Everyone ivcseciseseeskdiss 1 10 Use During Pregnancy 1 23 Safety Defects Reporting to Saturn 7 14 Reporting to the United States Government 7 14 Safety Warnings and Symbols iii Scheduled Maintenance 6 3 Additional Required Services 2 2 eeeeeeeeeee eee 6 6 Scheduling Appointments 7 8 Seatback Folding Passenger 1 8 Seats Driver Seat Height Adjuster naiean 1 4 Head Restraints 1 2 Heated Seats c ee 1 5 Manual Lumbar 1 5 Passenger Folding Seatback a a 1 8 Power Seat eeeeeeeee 1 4 Reclining Seatbacks 1 6 Split Folding Rear Seat 1 9 i 10 INDEX Securing a Child Restraint Rear Seat Position 1 37 Right Front Seat Position 1 39 Security Light e 3 38 Service 20 eee cec eee ee eee eeeee neers 5 3 Accessories and Modifications 4 5 3 Adding Equipment to the Outside of the Vehicle 5 5 Doing Your Own Work 5 4 Engine Soon Lamp 3 35 Publications Ordering Informa
374. so there is enough room for the road tire to be removed 5 67 Z CAUTION Getting under a vehicle when it is jacked up is dangerous If the vehicle slips off the jack you could be badly injured or killed Never get under a vehicle when it is supported only by a jack Z CAUTION Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall To help avoid personal injury and vehicle damage be sure to fit the jack lift head into the proper location before raising the vehicle 5 68 Service and Appearance Care Z CAUTION Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training If a jack is provided with the vehicle it is designed only for changing a flat tire If it is used for anything else you or others could be badly injured or killed if the vehicle slips off the jack If a jack is provided with the vehicle only use it for changing a flat tire 9 Remove any rust or dirt from the wheel bolts mounting surfaces and spare wheel 11 Reinstall the wheel nuts Tighten each nut by hand until the wheel is held against the hub Z CAUTION Z CAUTION Notice Make sure that the jack lift head is in the correct position or you may damage your vehicle The repairs would not be covered by your warranty 7 Remove all of the wheel nuts
375. splay Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings OFF There will be no delayed locking of the vehicle s doors ON default The doors will not lock until five seconds after the last door is closed NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Instrument Panel 3 61 EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside This happens after the key is turned from ON RUN to LOCK OFF Press the customization button until PRESS V TO SET EXIT LIGHTING appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings OFF The exterior lamps will not turn on 10 SECONDS default The exterior lamps will stay on for 10 seconds 3 62 Instrument Panel 30 SECONDS The exterior lamps will stay on for 30 seconds 2 MINUTES The exterior lamps will stay on for two minutes NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC APPROACH LIGHTING
376. system removes moisture from the air so a small amount of water might drip under the vehicle while idling or after turning off the engine Outside Air Press to turn the outside air mode on An indicator light comes on to show that outside air is on Air from outside the vehicle will circulate throughout the vehicle The outside air mode can be used with all modes but it cannot be used with the recirculation mode Pressing this button will cancel the recirculation mode lt amp Recirculation Press to turn on the recirculation mode An indicator light comes on to show that recirculation is on This mode recirculates and helps to quickly cool or heat the air inside the vehicle It can be used to prevent outside air and odors from entering the vehicle Avoid using the recirculation mode during high periods of humidity and cool outside temperatures since this may result in increased window fogging If window fogging is experienced select the defrost mode Recirculation mode is not available in floor defog or defrost modes and will shut off automatically and change to outside air If the button is selected in any of these modes the indicator will flash This helps prevent window fogging and moisture building up inside the vehicle Instrument Panel 3 23 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window The rear window defogger only works when th
377. t all wheel drive vehicles in this manual e Make sure all underbody shields if the vehicle has them are properly attached e Know the local laws that apply to off roading where you will be driving or check with law enforcement people in the area e Be sure to get the necessary permission if you will be on private land 4 14 Loading Your Vehicle for Off Road Driving Driving Your Vehicle CAUTION Continued Z CAUTION e Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop You or your passengers could be injured Keep cargo below the top of the seatbacks e Unsecured cargo on the load floor can be tossed about when driving over rough terrain You or your passengers can be struck by flying objects Secure the cargo properly Continued e Heavy loads on the roof raise the vehicle s center of gravity making it more likely to roll over You can be seriously or fatally injured if the vehicle rolls over Put heavy loads inside the cargo area not on the roof Keep cargo in the cargo area as far forward and low as possible There are some important things to remember about how to load your vehicle e The heaviest things should be on the floor forward of the rear axle Put heavier items as far forward as you can e Be sure the load is properly secured so things are not tossed around You will find other impor
378. t away the Roadside Assistance advisor may give you permission to get local emergency road service You will receive payment up to 100 after sending the original receipt to Roadside Assistance Mechanical failures may be covered however any cost for parts and labor for repairs not covered by the warranty are the owner responsibility Scheduling Service Appointments When your vehicle requires warranty service contact your dealer retailer and request an appointment By scheduling a service appointment and advising your service consultant of your transportation needs your dealer retailer can help minimize your inconvenience If your vehicle cannot be scheduled into the service department immediately keep driving it until it can be scheduled for service unless of course the problem is safety related If it is please call your dealership retailer let them know this and ask for instructions If the dealer retailer requests you to bring the vehicle for service you are urged to do so as early in the work day as possible to allow for the same day repair Courtesy Transportation To enhance your ownership experience we and our participating retailers are proud to offer Courtesy Transportation a customer support program for vehicles with the Bumper to Bumper Base Warranty Coverage period in Canada extended powertrain and hybrid specific warranties in both the U S and Canada Several courtesy transpor
379. t is hand tight and fully seated Coolant Surge Tank Pressure Cap Notice f the pressure cap is not tightly installed coolant loss and possible engine damage may occur Be sure the cap is properly and tightly secured If you need to replace your coolant surge tank pressure cap see your retailer Engine Overheating There is a coolant temperature warning light on your vehicle s instrument panel See Engine Coolant Temperature Warning Light on page 3 34 Service and Appearance Care lf Steam Is Coming From Your Engine Z CAUTION Steam from an overheated engine can burn you badly even if you just open the hood Stay away from the engine if you see or hear steam coming from it Just turn it off and get everyone away from the vehicle until it cools down Wait until there is no sign of steam or coolant before you open the hood If you keep driving when your engine is overheated the liquids in it can catch fire You or others could be badly burned Stop your engine if it overheats and get out of the vehicle until the engine is cool 5 25 Notice lf the engine catches fire because of being driven with no coolant your vehicle can be badly damaged The costly repairs would not be covered by the vehicle warranty If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam the problem may not be too serious Sometimes the engine can get a
380. t never be installed using only the top tether and anchor In order to use the LATCH system in your vehicle you need a child restraint that has LATCH attachments The child restraint manufacturer will provide you with instructions on how to use the child restraint and its attachments Seats and Restraint System The following explains how to attach a child restraint with these attachments in your vehicle Not all vehicle seating positions or child restraints have lower anchors and attachments or top tether anchors and attachments Lower Anchors Lower anchors A are metal bars built into the vehicle There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments B Top Tether Anchor A G hy FA ME A top tether A C anchors the top of the child restraint to the vehicle A top tether anchor is built into the vehicle The top tether attachment B on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash Your child restraint may have a single tether A or a dual tether C Either will have a single attachment B to secure the top tether to the anchor Some child restraints that have top tethers are designed for use with or without the top tether being attached Others require the top tether always to be atta
381. t night or during other times where visibility or traction may be limited such as on curves slippery roads or hilly terrain Unfamiliar surroundings can also have hidden hazards To help you learn more about driving in different conditions this section contains information about city freeway and off road driving as well as other hints for driving in various weather conditions Vehicle Design According to the U S Department of Transportation utility vehicles have a significantly higher rollover rate than other types of vehicles Utility vehicles do have higher ground clearance and a narrower track or shorter wheelbase than passenger cars to make them more capable for off road driving Specific design characteristics like these give the driver a better view of the road but also give utility vehicles a higher center of gravity than other types of vehicles This means that you should not expect a utility vehicle to handle the same way a vehicle with a lower center of gravity like a car would in similar situations But driver behavior factors are far more often the cause of a utility vehicle rollover than are environmental or vehicle factors Safe driver behavior and understanding the environment in which you will be driving can help avoid a rollover crash in any type of vehicle including utility vehicles Driving for Better Fuel Economy Driving habits can affect fuel mileage Here are some driving tips
382. t to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it This can cause wind noise and can affect fuel economy and windshield washer performance Check with your dealer retailer before adding equipment to the outside of the vehicle Service and Appearance Care 5 5 Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle To help keep the engine clean and maintain optimum vehicle performance we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline The 8th digit of the Vehicle Identification Number VIN shows the code letter or number that identifies the vehicle s engine The VIN is at the top left of the instrument panel See Vehicle Identification Number VIN on page 5 79 Gasoline Octane If the vehicle has the 2 4L L4 engine VIN Code P or the 3 5L V6 engine VIN Code N use regular unleaded gasoline with a posted octane rating of 87 or higher If the octane rating is less than 87 you might notice an audible knocking noise when you drive commonly referred to as spark knock If this occurs use a gasoline rated at 87 octane or higher as soon as possible If you are using gasoline rated at 87 octane or higher and you hear heavy knocking the engine needs service If the vehicle has the 3 6L V6 engine VIN Code 7 use regular unleaded gasoline with a posted octane rating of 87 or higher
383. table so you can sit up straight To see how see Seats in the Index 2 Pick up the latch plate and pull the belt across you Do not let it get twisted Seats and Restraint System 1 19 The lap shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly If the shoulder portion of a passenger belt is pulled out all the way the child restraint locking feature may be engaged If this happens let the belt go back all the way and start again Engaging the child restraint locking feature in the right front seating position may affect the passenger sensing system See Passenger Sensing System on page 1 51 for more information IW 3 Push the latch plate into the buckle until it clicks Pull up on the latch plate to make sure it is secure If the belt is not long enough see Safety Belt Extender on page 1 23 Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary 1 20 4 If equipped with a shoulder belt height adjuster move it to the height that is right for you See Shoulder Belt Height Adjustment later in this section for instructions on use and important safety information 5 To make the lap part tight pull up on the shoulder belt It may be necessary to pull the stitching on the safety belt through the latch
384. tant information under Loading the Vehicle on page 4 28 and Tires on page 5 43 Environmental Concerns Off road driving can provide wholesome and satisfying recreation However it also raises environmental concerns We recognize these concerns and urge every off roader to follow these basic rules for protecting the environment e Always use established trails roads and areas that have been specially set aside for public off road recreational driving and obey all posted regulations e Avoid any driving practice that could damage shrubs flowers trees or grasses or disturb wildlife This includes wheel spinning breaking down trees or unnecessary driving through streams or over soft ground e Always carry a litter bag and make sure all refuse is removed from any campsite before leaving Take extreme care with open fires where permitted camp stoves and lanterns e Never park your vehicle over dry grass or other combustible materials that could catch fire from the heat of the vehicle s exhaust system Traveling to Remote Areas It makes sense to plan your trip especially when going to a remote area Know the terrain and plan your route Get accurate maps of trails and terrain Check to see if there are any blocked or closed roads It is also a good idea to travel with at least one other vehicle in case something happens to one of them For vehicles with a winch be sure to read the winch inst
385. tation After the tires have been rotated adjust the front and rear inflation pressures as shown on the Tire and Loading Information label See Inflation Tire Pressure on page 5 49 and Loading the Vehicle on page 4 28 Reset the Tire Pressure Monitor System See Tire Pressure Monitor Operation on page 5 53 Make certain that all wheel nuts are properly tightened See Wheel Nut Torque under Capacities and Specifications on page 5 86 Z CAUTION Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after time The wheel could come off and cause an accident Continued 5 57 Service and Appearance Care CAUTION Continued When you change a wheel remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if needed to get all the rust or dirt off See Changing a Flat Tire on page 5 64 When It Is Time for New Tires Various factors such as maintenance temperatures driving speeds vehicle loading and road conditions influence when you need new tires G NNa y T ti ay fl AN GENO SUE BS Filji4 BS Saris ke One way to tell when it is time for new tires is to check the treadwear indicators which will appear when the tires have only 1 16 inch 1 6 mm or less of tread remai
386. tation options are available to assist in reducing your inconvenience when warranty repairs are required Courtesy Transportation is not a part of the New Vehicle Limited Warranty A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information Customer Assistance Information Transportation Options Warranty service can generally be completed while you wait However if you are unable to wait Saturn helps to minimize your inconvenience by providing several transportation options Depending on the circumstances your retailer can offer you one of the following Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation Retailers may provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule This includes one way or round trip shuttle service within reasonable time and distance parameters of the retailer s area 7 9 Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs and public transportation is used instead of the retailer s shuttle service the expense must be supported by original receipts and can only be up to the maximum amount allowed by Saturn for shuttle service In addition for U S customers should you arrange transportation through a friend or relative limited reimburseme
387. te the calibration The DIC will display COMPASS CALIBRATION COMPLETE for a few seconds when the calibration is complete The DIC display will then return to the previous menu Instrument Panel 3 49 DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition Multiple messages may appear one after another Some messages may not require immediate action but you can press any of the DIC buttons or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the messages and to clear them from the display Some messages cannot be cleared from the DIC display because they are more urgent These messages require action before they can be cleared Take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear not correct the problem 3 50 Instrument Panel The following are the possible messages that can be displayed and some information about them BATTERY SAVER ACTIVE This message displays when the charging system detects that the battery is being drained You may notice that the vehicle attempts to reduce the drain for you by turning off accessories such as interior fans rear defogger and heated seats Turn off all accessories If the vehicle is not running start
388. te the positive and negative terminal locations on that vehicle Open the hood on your vehicle and find the remote positive and remote negative jump starting terminals Your vehicle is equipped with a remote positive terminal This is located in the engine compartment on the driver side of the vehicle on the underhood fuse block See Engine Compartment Overview on page 5 12 for more information on location Service and Appearance Care To uncover the remote positive terminal press the tab on the bottom of the fuse block and lift the cover up The remote negative terminal is a stud on the driver side near the underhood fuse block Place the negative jumper cable clamp on the negative terminal on top of the battery Z CAUTION Z CAUTION An electric fan can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electric fan Using a match near a battery can cause battery gas to explode People have been hurt doing this and some have been blinded Use a flashlight if you need more light Be sure the battery has enough water You do not need to add water to the battery installed in your new vehicle But if a battery has filler caps be sure the right amount of fluid is there If it is low add water to take care of that first If you do not explosive gas could be present
389. tection this way Z CAUTION You can be seriously hurt if your lap belt is too loose In a crash you could slide under the lap belt and apply force on your abdomen This could cause serious or even fatal injuries The lap belt should be worn low and snug on the hips just touching the thighs 1 16 Seats and Restraint System Q What is wrong with this A The belt is buckled in the wrong buckle Z CAUTION You can be seriously injured if your belt is buckled in the wrong place like this In a crash the belt would go up over your abdomen The belt forces would be there not on the pelvic bones This could cause serious internal injuries Always buckle your belt into the buckle nearest you Q What is wrong with this A The belt is over an armrest Z CAUTION You can be seriously injured if your belt goes over an armrest like this The belt would be much too high In a crash you can slide under the belt The belt force would then be applied on the abdomen not on the pelvic bones and that could cause serious or fatal injuries Be sure the belt goes under the armrests Seats and Restraint System 1 17 Q What is wrong with this A The shoulder belt is worn under the arm It should be worn over the shoulder at all times Z CAUTION You can be seriously injured if you wear the shoulder belt under your arm In a crash your body
390. ted or corroded If wheel nuts keep coming loose the wheel wheel bolts and wheel nuts should be replaced If the wheel leaks air replace it except some aluminum wheels which can sometimes be repaired See your dealer retailer if any of these conditions exist Your dealer retailer will know the kind of wheel you need Each new wheel should have the same load carrying capacity diameter width offset and be mounted the same way as the one it replaces If you need to replace any of your wheels wheel bolts or wheel nuts replace them only with new Saturn original equipment parts This way you will be sure to have the right wheel wheel bolts and wheel nuts for your vehicle Service and Appearance Care Z CAUTION Used Replacement Wheels Using the wrong replacement wheels wheel bolts or wheel nuts on your vehicle can be dangerous It could affect the braking and handling of your vehicle make your tires lose air and make you lose control You could have a collision in which you or others could be injured Always use the correct wheel wheel bolts and wheel nuts for replacement Z CAUTION Notice The wrong wheel can also cause problems with bearing life brake cooling speedometer or odometer calibration headlamp aim bumper height vehicle ground clearance and tire or tire chain clearance to the body and chassis See Changing a Flat Tire on page 5 64 for more information
391. ted people are hurt more often in crashes than those who are wearing safety belts Occupants who are not buckled up can be thrown out of the vehicle in a crash And they can strike others in the vehicle who are wearing safety belts Seats and Restraint System First before you or your passenger s wear a safety belt there is important information you should know Sit up straight and always keep your feet on the floor in front of you The lap part of the belt should be worn low and snug on the hips just touching the thighs In acrash this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt If you slid under it the belt would apply force on your abdomen This could cause serious or even fatal injuries The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces The shoulder belt locks if there is a sudden stop or crash Seats and Restraint System 1 15 Q What is wrong with this A The shoulder belt is too loose It will not give as much protection this way Z CAUTION You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could increase injury The shoulder belt should fit snugly against your body Q What is wrong with this A The lap belt is too loose It will not give nearly as much pro
392. tem from overheating When the system cools down the AWD system will activate again automatically this cool down can take up to 20 minutes depending on outside temperature and vehicle use Steering Electric Power Steering If the vehicle has the electric power steering system and the engine stalls while driving the power steering assist system will continue to operate until you are able to stop the vehicle If power steering assist is lost because the electric power steering system is not functioning the vehicle can be steered but it will take more effort 4 10 If you turn the steering wheel in either direction several times until it stops or hold the steering wheel in the stopped position for an extended amount of time you may notice a reduced amount of power steering assist The normal amount of power steering assist should return shortly after a few normal steering movements The electric power steering system does not require regular maintenance If you suspect steering system problems and or the Service Vehicle Soon light comes on contact your dealer retailer for service repairs Hydraulic Power Steering If the vehicle has the hydraulic power steering system and power steering assist is lost because the engine stops or the power steering system is not functioning the vehicle can be steered but it will take more effort Driving Your Vehicle Steering Tips It is important to take curves at a
393. ter remains caked with dirt a new filter is required 5 17 To inspect or replace the engine air cleaner filter do the following 1 Remove the clamp on the air duct hose 2 Disconnect the hose 3 Remove the four bolts on the side of the air cleaner assembly 4 Turn the cover upward to disengage the cover hinges 5 Remove the air cleaner cover assembly and air filter element 5 18 6 Inspect or replace the air filter element If the air filter element is dirty you should replace it If it is only dusty it may be cleaned by blowing compressed air through it from the clean side Make sure you are away from the engine compartment when cleaning the air filter with compressed air Wipe all dust from inside of the housing and inspect the air cleaner and air outlet duct for cracks cuts and deterioration The air outlet duct must be replaced if damaged 7 Reverse Steps 1 through 5 to reinstall the engine air cleaner filter cover and air duct hose Service and Appearance Care Z CAUTION Operating the engine with the air cleaner filter off can cause you or others to be burned The air cleaner not only cleans the air it helps to stop flames if the engine backfires If it is not there and the engine backfires you could be burned Do not drive with it off and be careful working on the engine with the air cleaner filter off Notice If the air cleaner filter is off a
394. th the ignition on The fan must be turned on to run the air conditioning compressor There will be some airflow noticeable from the various outlets when driving even with the fan in the off position To turn off the air completely turn the fan to O and select the recirculation button 3 22 Instrument Panel Temperature Control Turn clockwise or counterclockwise to increase or decrease the temperature Select the desired cabin air temperature between 60 90 F 16 32 C Typically the best setting is near 75 F 23 C Choosing the coldest or warmest temperature setting does not cause the system to heat or cool any faster Air Delivery Mode Control Turn clockwise or counterclockwise to change the current airflow mode Select from the following air delivery modes Vent Air is directed to the instrument panel outlets 74 Bi Level Air is divided between the instrument panel outlets and the floor outlets tpd Floor Air is directed to the floor outlets with some air directed to the windshield When this mode is selected the system turns the recirculation mode off Recirculation mode cannot be selected while in floor mode This is to help prevent window fogging a Defog This mode clears the windows of fog or moisture Air is directed to the floor outlets with some air directed to the windshield and side window outlets In this mode the system turns the recirculation mode off and runs the
395. that comes into contact with the road Treadwear Indicators Narrow bands sometimes called wear bars that show across the tread of a tire when only 1 16 inch 1 6 mm of tread remains See When It Is Time for New Tires on page 5 57 UTQGS Uniform Tire Quality Grading Standards A tire information system that provides consumers with ratings for a tire s traction temperature and treadwear Ratings are determined by tire manufacturers using government testing procedures The ratings are molded into the sidewall of the tire See Uniform Tire Quality Grading on page 5 60 Vehicle Capacity Weight The number of designated seating positions multiplied by 150 lbs 68 kg plus the rated cargo load See Loading the Vehicle on page 4 28 Vehicle Maximum Load on the Tire Load on an individual tire due to curb weight accessory weight occupant weight and cargo weight Vehicle Placard A label permanently attached to a vehicle showing the vehicle s capacity weight and the original equipment tire size and recommended inflation pressure See Tire and Loading Information Label under Loading the Vehicle on page 4 28 Service and Appearance Care Inflation Tire Pressure Tires need the correct amount of air pressure to operate effectively Notice Do not let anyone tell you that under inflation or over inflation is all right It is not If your tires do not have enough air under inflation yo
396. that is unprotected by any bony structure This alone could cause serious or fatal injuries To reduce the risk of serious or fatal injuries during a crash young children should always be secured in appropriate child restraints child restraints Child Restraint Systems A Rear Facing Infant Seat A rear facing infant seat A provides restraint with the seating surface against the back of the infant The harness system holds the infant in place and in a crash acts to keep the infant positioned in the restraint Seats and Restraint System 1 29 B Forward Facing Child Seat A forward facing child seat B provides restraint for the child s body with the harness C Booster Seats A booster seat C is a child restraint designed to improve the fit of the vehicle s safety belt system A booster seat can also help a child to see out the window 1 30 Securing an Add On Child Restraint in the Vehicle Z CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle Secure the child restraint properly in the vehicle using the vehicle s safety belt or LATCH system following the instructions that came with that child restraint and the instructions in this manual To help reduce the chance of injury the child restraint must be secured in the vehicle Child restraint systems must be secured in
397. the manual gate While driving in manual shift mode the transmission will remain in the driver gear selected When coming toa stop in the manual position the vehicle will automatically shift to 1 First gear 2 Push the shift lever forward toward the plus to upshift or rearward toward the minus to downshift The instrument panel will display the actual gear selected In manual shift mode all six forward gears can be selected Features and Controls While using the MSM feature the vehicle will have operation similar to a manual transmission You can use this for sport driving or when driving hilly roads to stay in gear longer or to downshift for more power or engine braking The transmission will only allow you to shift into gears appropriate for the vehicle speed e The transmission will not automatically shift to the next higher gear without moving the shift lever e The transmission will not allow shifting to the next lower gear if the vehicle speed is too high If the vehicle does not respond to a gear change or detects a problem with the transmission the range of gears may be reduced and the Malfunction Indicator Lamp will come on See Malfunction Indicator Lamp on page 3 35 2 21 2 Second and 3 Third Gear Start Feature When accelerating the vehicle from a stop in snowy and icy conditions you may want to select 2 Second and 3 Third gear A higher gear and light applicatio
398. the front 1 L i mT a nels imam a To tow the vehicle from the front with the rear wheels on the ground do the following 1 Put the front wheels on a dolly 2 Move the shift lever to P Park 3 Set the parking brake 4 Clamp the steering wheel in a straight ahead position with a clamping device designed for towing 5 Remove the key from the ignition 6 Secure the vehicle to the dolly 7 Release the parking brake Towing the Vehicle From the Rear Ov Notice Towing the vehicle from the rear could damage it Also repairs would not be covered by the vehicle warranty Never have the vehicle towed from the rear Towing a Trailer Driving Your Vehicle Z CAUTION The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly For example if the trailer is too heavy the brakes may not work well or even at all The driver and passengers could be seriously injured The vehicle may also be damaged the resulting repairs would not be covered by the vehicle warranty Pull a trailer only if all the steps in this section have been followed Ask your dealer retailer for advice and information about towing a trailer with the vehicle 4 35 Notice Pulling a trailer improperly can damage the vehicle and result in costly repairs not covered by the vehicle warranty To pull a trailer correctly f
399. the key is turned to the ON RUN position The climate control system turns on at the setting the vehicle was set to when the vehicle was last turned off Laws in some communities may restrict the use of remote starters For example some laws may require a person using the remote start to have the vehicle in view when doing so Check local regulations for any requirements on remote starting of vehicles If the vehicle is low on fuel only one 10 minute remote start is allowed to help avoid running out of fuel 2 6 Features and Controls If the vehicle has the remote start feature the RKE transmitter functions have an increased range of operation However the range may be less while the vehicle is running There are other conditions which can affect the performance of the transmitter see Remote Keyless Entry RKE System on page 2 3 for additional information Q Remote Start This button is located on the RKE transmitter if the vehicle has remote start To start the vehicle 1 Aim the transmitter at the vehicle 2 Press and release then immediately press and hold Q until the turn signal lamps flash If the vehicle s lamps cannot be seen press and hold Q for at least two seconds The vehicle s doors lock Pressing Q again after the vehicle has started shuts the vehicle off When the vehicle starts the parking lamps turn on and remain on while the vehicle is running 3 After enterin
400. the vehicle any cargo carried in it and the people who will be riding in the vehicle If there are a lot of options equipment passengers or cargo in the vehicle it will reduce the tongue weight the vehicle can carry which will also reduce the trailer weight the vehicle can tow If towing a trailer the tongue load must be added to the GVW because the vehicle will be carrying that weight too See Loading the Vehicle on page 4 28 for more information about the vehicle s maximum load capacity Driving Your Vehicle For a weight carrying hitch the trailer tongue A should weigh 10 percent of the total loaded trailer weight B After loading the trailer weigh the trailer and then the tongue separately to see if the weights are proper If they are not adjustments might be made by moving some items around in the trailer Trailering may be limited by the vehicle s ability to carry tongue weight Tongue weight cannot cause the vehicle to exceed the GVWR Gross Vehicle Weight Rating or the RGAWR Rear Gross Axle Weight Rating The effect of additional weight may reduce the trailering capacity more than the total of the additional weight Consider the following example A vehicle model base weight is 5 500 Ibs 2 495 kg 2 800 Ibs 1 270 kg at the front axle and 2 700 lbs 1 225 kg at the rear axle It has a GVWR of 7 200 Ibs 3 266 kg a RGAWR of 4 000 Ibs 1 814 kg and a GCWR Gross Combinatio
401. the video device from high temperature conditions Once conditions return to normal the device will reset and the green indicator will stop flashing During any of these fault conditions the display will be blank and the indicator will continue to flash as long as the vehicle is in R Reverse or until the conditions return to normal Pressing and holding when the left indicator light is flashing will turn off the video display along with the left indicator light 2 33 OnStar System m m OnStar uses several innovative technologies and live advisors to provide a wide range of safety security information and convenience services If the airbags deploy the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location If the keys are locked in the vehicle call OnStar at 1 888 4 ONSTAR to have a signal sent to unlock the doors OnStar Hands Free Calling including 30 trial minutes good for 60 days is available on most vehicles OnStar Turn by Turn Navigation service with one trial route is available on most vehicles Press the OnStar button to have an OnStar advisor contact Roadside Service 2 34 OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until t
402. these surfaces itis very easy to lose control On wet ice for example the traction is so poor that you will have difficulty accelerating And if the vehicle does get moving poor steering and difficult braking can cause it to slide out of control Z CAUTION Driving on frozen lakes ponds or rivers can be dangerous Underwater springs currents under the ice or sudden thaws can weaken the ice Your vehicle could fall through the ice and you and your passengers could drown Drive your vehicle on safe surfaces only 4 22 Driving in Water Driving Your Vehicle Z CAUTION Driving through rushing water can be dangerous Deep water can sweep your vehicle downstream and you and your passengers could drown If it is only shallow water it can still wash away the ground from under your tires and you could lose traction and roll the vehicle over Do not drive through rushing water Heavy rain can mean flash flooding and flood waters demand extreme caution Find out how deep the water is before driving through it Do not try it if it is deep enough to cover the wheel hubs axles or exhaust pipe you probably will not get through Deep water can damage the axle and other vehicle parts If the water is not too deep drive slowly through it At faster speeds water splashes on the ignition system and the vehicle can stall Stalling can also occur if you get the tailpipe under wate
403. ting Disc displays Once the disc is ejected Remove Disc displays The CD R or CD RW can be removed If the CD R or CD RW is not removed after several seconds the CD R or CD RW automatically pulls back into the player and begins playing For the Six Disc CD player press and hold this button for two seconds to eject all discs J Tune Turn to select MP3 files on the CD R or CD RW currently playing K SEEK D Press the left arrow to go to the start of the current MP3 file if more than ten seconds have played Press the right arrow to go to the next MP3 file If either arrow is held or pressed multiple times the player continues moving backward or forward through MP3 files on the CD 3 78 Instrument Panel lt Previous Folder Press the pushbutton positioned under the Folder label to go to the first track in the previous folder gt Next Folder Press the pushbutton positioned under the Folder label to go to the first track in the next folder lt lt REV Reverse Press and hold to reverse playback quickly within an MP3 file Sound is heard at a reduced volume Release to resume playing the file The elapsed time of the file displays b gt FWD Fast Forward Press and hold to advance playback quickly within an MP3 file Sound is heard at a reduced volume Release to resume playing the file The elapsed time of the file displays RDM Random With the random setting the MP
404. tion 5 7 15 Scheduling Appointments 7 8 Vehicle Soon Light 3 40 Service Parts Identification Fabel scents ofabalsncnoaite seamateee 5 79 Servicing Your Airbag Equipped Vehicle 1 56 Setting the Clock 3 65 Sheet Metal Damage 5 78 Shifting Out of Park eeeeee 2 27 Shifting Into Park 2 25 Signals Turn and Lane Change 06eee 3 6 Spare Tire COMPACT csiis soues moniy 5 71 listalig oen ieiarae ies 5 66 REMOVING serssslisir ee 5 65 SUOMNG Ceriani 5 70 Specifications and Capacities ce 5 86 Speedometer 2 0eee 3 28 Split Folding Rear Seat 1 9 StabiliTrak Indicator Light 3 33 StabiliTrak System 4 7 Start Vehicle Remote 2 5 Starting the Engine 2 17 SICGVIAG secstcasseecsitsarsnonssceacs 4 9 Power Warning Lights 3 33 Steering Wheel Controls AUGIO 00 ccc ecceeceeee een eeeeenes 3 92 Steering Wheel Tilt Wheel 3 6 Storage Areas Cargo Management SySteM penteun 2 44 Center Console 2 42 Convenience Net 2 44 Cupholders 066 2 41 Front Storage Area 2 42 Glove BOX s eeeeees 2 41 Instrument Panel 2 42 Storage Areas cont Luggage Carrier Rear Seat Armrest Sunglasses Storage Compartment Stuck in Sand Mud Ice
405. tnote d a i Inspect restraint system components See footnote e a ee Lubricate body components See footnote f a i Automatic Transmission Only Check automatic transmission fluid level and add fluid as needed Replace passenger compartment air filter See footnote k a i L4 engine Inspect throttle system See footnote g a i 6 6 Maintenance Schedule Additional Required Services The following services should be performed at the first maintenance service I or II after the indicated miles kilometers shown for each item Additional Required Services gt 25 000 50 000 75 000 100 000 125 000 150 000 Service and Miles Kilometers 40000 80000 120 000 160 000 200 000 240 000 Inspect fuel system for damage or leaks Inspect exhaust system for loose or damaged components Replace engine air cleaner filter See Engine Air Cleaner Filter on page 5 17 anes automatic transmission fluid severe service See footnote h Change cag transmission fluid normal service Replace spark plugs An Emission Control Service Maintenance Schedule 6 7 Additional Required Services cont d 25 000 50 000 75 000 100 000 125 000 150 000 Service and Miles Kilometers 40000 80 000 120 000 160000 200 000 240 000 service See footnote rt Change transfer case fluid normal service See footnote m Engine cooling system service or every five years whic
406. to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages Setting the Tone Bass Midrange Treble BASS MID TREB Bass Midrange or Treble To adjust bass midrange or treble press the JJ knob until the tone control tabs display Continue pressing to highlight the desired tab or press the pushbutton positioned under the desired tab Turn the Jd knob to adjust the highlighted setting Bass midrange or treble can also be adjusted Y ressing etg SEEK arrow FWD or II REV when the setting is highlighted until the desired level is obtained If a station s frequency is weak or has static decrease the treble To quickly adjust bass midrange or treble to the middle position press the pushbutton positioned under the BASS MID or TREB tab for more than two seconds A beep sounds and the level adjusts to the middle position To quickly adjust all tone and speaker controls to the middle position press the dJ knob for more than two seconds until a beep sounds EQ Equalization Press to select preset equalization settings To return to the manual mode press the EQ button until Manual displays or manually adjust the bass midrange or treble by pressing the JJ knob Instrument Panel 3 69 Adjusting the Speakers Balance Fade BAL FADE Balance Fade To adjust balance or fade press t
407. to the right lane you could hit a vehicle on the right Check the inside mirror or glance over your shoulder before changing lanes The passenger side mirror is convex shaped A convex mirror s surface is curved so more can be seen from the driver seat Outside Heated Mirrors For vehicles with outside heated mirrors Gt Rear Window Defogger Press to heat the outside rearview mirrors See Rear Window Defogger under Automatic Climate Control System on page 3 20 for more information Object Detection Systems Rear Vision Camera RVC The vehicle may have a Rear Vision Camera system Read this entire section before using it Features and Controls CAUTION Continued Z CAUTION The Rear Vision Camera RVC system does not replace driver vision RVC does not e Detect objects that are outside the camera s field of view below the bumper or underneath the vehicle e Detect children pedestrians bicyclists or pets Continued Do not back the vehicle by only looking at the rear vision camera screen or use the screen during longer higher speed backing maneuvers or where there could be cross traffic Your judged distances using the screen will differ from actual distances So if you do not use proper care before backing up you could hit a vehicle child pedestrian bicyclist or pet resulting in vehicle damage injury or death Even though the vehicle has the
408. to the vehicle or the EDR Saturn will not access this data or share it with others except with the consent of the vehicle owner or if the vehicle is leased with the consent of the lessee in response to an official request of police or similar government office as part of Saturn s defense of litigation through the discovery process or as required by law Data that Saturn collects or receives may also be used for Saturn research needs or may be made available to others for research purposes where a need is shown and the data is not tied to a specific vehicle or vehicle owner Customer Assistance Information OnStar If your vehicle has OnStar and you subscribe to the OnStar services please refer to the OnStar Terms and Conditions for information on data collection and use See also OnStar System on page 2 33 in this manual for more information Navigation System If your vehicle has a navigation system use of the system may result in the storage of destinations addresses telephone numbers and other trip information Refer to the navigation system operating manual for information on stored data and for deletion instructions 7 17 Radio Frequency Identification RFID RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security as well as in connection with conveniences such as key fobs for remote door locking unlocking and starting a
409. traint System e Can proper safety belt fit be maintained for the length of the trip If yes continue If no return to the booster seat Q What is the proper way to wear Safety belts A An older child should wear a lap shoulder belt and get the additional restraint a shoulder belt can provide The shoulder belt should not cross the face or neck The lap belt should fit snugly below the hips just touching the top of the thighs This applies belt force to the child s pelvic bones in a crash It should never be worn over the abdomen which could cause severe or even fatal internal injuries in a crash Also see Rear Safety Belt Comfort Guides under Lap Shoulder Belt on page 1 19 According to accident statistics children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position In a crash children who are not buckled up can strike other people who are buckled up or can be thrown out of the vehicle Older children need to use safety belts properly Seats and Restraint System Z CAUTION Z CAUTION Never do this Never allow two children to wear the same safety belt The safety belt can not properly spread the impact forces In a crash the two children can be crushed together and seriously injured A safety belt must be used by only one person at a time nD Never do this Nev
410. tting hot Watch out for the engine cooling fan By this time the coolant level inside the coolant surge tank may be lower If the level is lower add more of the proper DEX COOL coolant mixture to the coolant surge tank until the level reaches between the MIN and MAX lines 5 Then replace the pressure cap Be sure the pressure cap is hand tight Check the level in the surge tank when the cooling system has cooled down If the coolant is not at the proper level repeat Steps 1 through 3 and reinstall the pressure cap If the coolant still is not at the proper level when the system cools down again see your dealer retailer Engine Coolant The cooling system in your vehicle is filled with DEX COOL engine coolant This coolant is designed to remain in your vehicle for five years or 150 000 miles 240 000 km whichever occurs first if you add only DEX COOL extended life coolant The following explains your cooling system and how to add coolant when it is low If you have a problem with engine overheating see Engine Overheating on page 5 25 A 50 50 mixture of clean drinkable water and DEX COOL coolant will e Give freezing protection down to 34 F 37 C e Give boiling protection up to 265 F 129 C e Protect against rust and corrosion e Help keep the proper engine temperature e Let the warning lights and gages work as they should Notice Using coolant other than DEX COOL
411. ture Warning Light Cooling System Drive Belt Routing Exhaust arenie Oil Oil Life System 0 Overheating Reduced Power Light Starting Entry Lighting Reporting Safety Defects to the United States Government Event Data Recorders Extender Safety Belt Exterior Lamps F Filter Engine Air Cleaner 5 17 Finish Damage 000 5 78 Fixed Mast Antenna 3 93 Flashers Hazard Warning 3 5 Flash to PasSs ioeina 3 7 Flat TIE siirteen ud 5 63 Flat Tire Changing 5 64 Flat Tire Storing 008 5 70 Fluid Automatic Transmission 5 18 Power Steering 005 5 26 Windshield Washer 5 27 Fog Lamp FOG kenn 3 14 Fog Lamp Light 3 38 Folding Rear Seat 0 1 9 Folding Seatback Passenger 1 8 Front Storage Area 0 5 2 42 PUGH aroan na a Era 5 5 Additives ceeeeeeeeeees 5 6 California Fuel 05 5 6 Economy Driving 4 3 Filling a Portable Fuel Container cceeeeeeee 5 10 Fuel cont Filling the Tank 06 5 8 Fuels in Foreign Countries 5 8 Gage ssc weer iecinns 3 41 Gasoline Octane 5 5 Gasoline Specifications 5 6 Low Fuel Warning Light 3 41 Fuses Fuses and Circuit Breakers sisenes 5 80 Instrument Panel Fuse BIOCK cceceeeeeeeeeee ees 5 80 Underhood Fuse Block
412. u can get the following Too much flexing e Too much heat e Tire overloading Premature or irregular wear Poor handling Reduced fuel economy If your tires have too much air over inflation you can get the following e Unusual wear Poor handling Rough ride e Needless damage from road hazards 5 49 A vehicle specific Tire and Loading Information label is attached to your vehicle This label shows your vehicle s original equipment tires and the correct inflation pressures for your tires when they are cold The recommended cold tire inflation pressure shown on the label is the minimum amount of air pressure needed to support your vehicle s maximum load carrying capacity For additional information regarding how much weight your vehicle can carry and an example of the Tire and Loading Information label see Loading the Vehicle on page 4 28 How you load your vehicle affects vehicle handling and ride comfort Never load your vehicle with more weight than it was designed to carry 5 50 When to Check Check your tires once a month or more Do not forget to check the compact spare tire it should be at 60 psi 420 kPa For additional information regarding the compact spare tire see Compact Spare Tire on page 5 71 How to Check Use a good quality pocket type gage to check tire pressure You cannot tell if your tires are properly inflated simply by looking at them Radial t
413. uld get out as soon as after they deploy Some components it is safe to do so If you have of the airbag module may be hot breathing problems but cannot get for several minutes For location of out of the vehicle after an airbag the airbag modules see What inflates then get fresh air by Makes an Airbag Inflate on opening a window or a door page 1 49 If you experience breathing The parts of the airbag that come problems following an airbag into contact with you may be warm deployment you should seek but not too hot to touch There may medical attention be some smoke and dust coming from the vents in the deflated airbags Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle nor does it prevent people from leaving the vehicle The vehicle has a feature that may automatically unlock the doors turn the interior lamps on and turn the hazard warning flashers on when the airbags inflate You can lock the doors turn the interior lamps off and turn the hazard warning flashers off by using the controls for those features You must first however turn the ignition key to the following ignition switch positions 1 Turn the ignition key to LOCK OFF 2 Turn the ignition key to ON RUN In many crashes severe enough to inflate the airbag windshields are broken by vehicle deformation Additional windshield breakage may also occur from the right front pass
414. ume will be set to a normal level LOUD The chime volume will be set to a loud level NO CHANGE No change will be made to this feature The current setting will remain There is no default for chime volume The volume will stay at the last known setting To select a setting press the set reset button while the desired setting is displayed on the DIC REMOTE START If your vehicle has this feature it allows you to turn the remote start off or on The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry RKE transmitter See Remote Vehicle Start on page 2 5 for more information Press the customization button until PRESS TO SET REMOTE START appears on the DIC display Press the set reset button once to access the settings for this feature Then press the customization button to scroll through the following settings OFF The remote start feature will be disabled ON default The remote start feature will be enabled NO CHANGE No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings Press the customization button until PRESS TO RESTORE DEFAULTS appears on the DIC display Press the set reset butto
415. ure will The vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture the engine could get too hot but you would not get the overheat warning The engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine Notice In cold weather water can freeze and crack the engine radiator heater core and other parts Use the recommended coolant and the proper coolant mixture 1 You can remove the coolant surge tank pressure cap when the cooling system including the coolant surge tank pressure cap and upper radiator hose is no longer hot Turn the pressure cap slowly counterclockwise about one quarter of a turn If you hear a hiss wait for that to stop 5 22 This will allow any pressure still left to be vented out the discharge hose 2 Then keep turning the pressure cap slowly and remove it F dies ave DS 3 Fill the coolant surge tank with the proper DEX COOL coolant mixture to between the MIN and MAX lines Service and Appearance Care 4 With the coolant surge tank pressure cap off start the engine and let it run until you can feel the upper radiator hose ge
416. urs first Any repairs would not be covered by the vehicle warranty Always use DEX COOL silicate free coolant in the vehicle How to Add Coolant to the Coolant Surge Tank Notice This vehicle has a specific coolant fill procedure Failure to follow this procedure could cause the engine to overheat and be severely damaged If you have not found a problem yet check to see if coolant is visible in the surge tank If coolant is visible but the coolant level is not at between the MIN and MAX lines add a 50 50 mixture of clean drinkable water and DEX COOL coolant at the coolant surge tank but be sure the cooling system including the coolant surge tank pressure cap is cool before you do it See Engine Coolant on page 5 22 for more information Service and Appearance Care 5 21 Z CAUTION Z CAUTION Z CAUTION Steam and scalding liquids from a hot cooling system can blow out and burn you badly They are under pressure and if you turn the coolant surge tank pressure cap even a little they can come out at high speed Never turn the cap when the cooling system including the coolant surge tank pressure cap is hot Wait for the cooling system and coolant surge tank pressure cap to cool if you ever have to turn the pressure cap Adding only plain water to the cooling system can be dangerous Plain water or some other liquid such as alcohol can boil before the proper coolant mixt
417. usly illuminated This sequence will continue upon subsequent vehicle start ups as long as the malfunction exists When the malfunction indicator is illuminated the system may not be able to detect or signal low tire pressure as intended TPMS malfunctions may occur for a variety of reasons including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to Service and Appearance Care ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly See Tire Pressure Monitor Operation on page 5 53 for additional information Federal Communications Commission FCC and Industry and Science Canada The Tire Pressure Monitor System TPMS operates on a radio frequency and complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Vehicles with TPMS operate on a radio frequency and comply with RSS 210 of Industry and Science Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interfe
418. ut Protection When the power door lock switch is pressed with the key in the ignition and any door is open all the doors lock and the driver door unlocks When doors are closed with the key in the ignition the horn will sound as a reminder If the doors are locked with the Remote Keyless Entry RKE transmitter and the key is in the ignition a chime sounds and all except the driver door lock The lockout protection feature can be overridden by holding the power door lock switch for three seconds Liftgate Z CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate trunk hatch open or with any objects that pass through the seal between the body and the trunk hatch or liftgate Engine exhaust contains Carbon Monoxide CO which cannot be seen or smelled It can cause unconsciousness and even death If the vehicle must be driven with the liftgate or trunk hatch open e Close all of the windows e Fully open the air outlets on or under the instrument panel Continued CAUTION Continued e Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting See Climate Control System in the Index e If the vehicle is equipped with a power liftgate disable the power liftgate function For more information about carbon monoxide see Engine Exhaust on page 2 28 To lock or unlock the liftgat
419. utomatic dimming inside rearview mirror Vehicles with OnStar have three additional control buttons for the OnStar system See your dealer retailer for more information about OnStar and how to subscribe to it See OnStar System on page 2 33 for more information about the services OnStar provides D On Off Press to turn the dimming feature on or off Features and Controls 2 29 Your vehicle may also have a Rear Vision Camera See Rear Vision Camera RVC on page 2 31 for more information Automatic Dimming Mirror Operation The automatic dimming mirror reduces the glare from the headlamps of the vehicle behind you The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start Outside Power Mirrors Controls for the outside power mirrors are located on the driver door 2 30 To adjust the power mirrors 1 Turn the knob to choose the left L or the R right mirror 2 Adjust each mirror so that you can see the side of your vehicle and the area behind your vehicle 3 Return the control to the center position so the mirror cannot be moved The mirrors can be manually folded inward toward the vehicle Return to the original position to use correctly Features and Controls Outside Convex Mirror Z CAUTION A convex mirror can make things like other vehicles look farther away than they really are If you cut too sharply in
420. vehicle See Compact Spare Tire on page 5 71 Z CAUTION If you use bias ply tires on the vehicle the wheel rim flanges could develop cracks after many miles of driving A tire and or wheel could fail suddenly causing a crash Use only radial ply tires with the wheels on the vehicle If you must replace your vehicle s tires with those that do not have a TPC Spec number make sure they are the same size load range speed rating and construction type radial and bias belted tires as your vehicle s original tires Vehicles that have a tire pressure monitoring system could give an inaccurate low pressure warning if non TPC Spec rated tires are installed on your vehicle Service and Appearance Care Non TPC Spec rated tires may give a low pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires See Tire Pressure Monitor System on page 5 51 Your vehicle s original equipment tires are listed on the Tire and Loading Information Label See Loading the Vehicle on page 4 28 for more information about the Tire and Loading Information Label and its location on your vehicle Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires this may affect the way your vehicle performs including its braking ride and handling characteristics stability and resist
421. ving backward or forward through the tracks on the CD lt lt REV Fast Reverse Press and hold to reverse playback quickly within a track Sound is heard at a reduced volume Release to resume playing the track The elapsed time of the track displays gt gt Fwo Fast Forward Press and hold to advance playback quickly within a track Sound is heard at a reduced volume Release to resume playing the track The elapsed time of the track displays RDM Random With the random setting the tracks can be listened to in random rather than sequential order on one CD or all CDs ina six disc CD player To use random e Press the pushbutton positioned under the RDM tab until Random Current Disc displays to play the tracks from a CD in random order Press again to turn off random play e Press the pushbutton positioned under the RDM tab until Randomize All Discs displays to play tracks from all CDs loaded in a six disc CD player in random order Press again to turn off random play BAND Press to listen to the radio when a CD is playing The CD remains inside the radio for future listening CD AUX CD Auxiliary Press to play a CD when listening to the radio The CD icon and track number displays when a CD is in the player Instrument Panel 3 73 The radio system has an auxiliary input jack located on the lower right side of the faceplate An external audio device such as a portable audio player can
422. vironment All recommended maintenance is important Improper vehicle maintenance can even affect the quality of the air we breathe Improper fluid levels or the wrong tire inflation can increase the level of emissions from the vehicle To help protect the environment and to keep the vehicle in good condition be sure to maintain the vehicle properly 6 2 Using the Maintenance Schedule We want to help keep this vehicle in good working condition But we do not know exactly how you will drive it You might drive very short distances only a few times a week Or you might drive long distances all the time in very hot dusty weather You might use the vehicle in making deliveries Or you might drive it to work to do errands or in many other ways Because of all the different ways people use their vehicles maintenance needs vary You might need more frequent checks and replacements So please read the following and note how you drive If you have any questions on how to keep the vehicle in good condition see your dealer retailer Maintenance Schedule This schedule is for vehicles that e carry passengers and cargo within recommended limits on the Tire and Loading Information label See Loading the Vehicle on page 4 28 e are driven on reasonable road surfaces within legal driving limits e are driven off road in the recommended manner See Off Road Driving on page 4 13 e use the recommended fuel See G
423. w vehicle e When you are being passed ease to the right 4 12 Loss of Control Let us review what driving experts say about what happens when the three control systems brakes steering and acceleration do not have enough friction where the tires meet the road to do what the driver has asked In any emergency do not give up Keep trying to steer and constantly seek an escape route or area of less danger Skidding In a skid a driver can lose control of the vehicle Defensive drivers avoid most skids by taking reasonable care suited to existing conditions and by not overdriving those conditions But skids are always possible The three types of skids correspond to the vehicle s three control systems In the braking skid the wheels are not rolling In the steering Driving Your Vehicle or cornering skid too much speed or steering in a curve causes tires to slip and lose cornering force And in the acceleration skid too much throttle causes the driving wheels to spin Remember Any traction control system helps avoid only the acceleration skid If the traction control system is off then an acceleration skid is best handled by easing your foot off the accelerator pedal If the vehicle starts to slide ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go If you start steering quickly enough the vehicle may straighten out Always be ready for a
424. wer steering fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise A fluid loss in this system could indicate a problem Have the system inspected and repaired How to Check Power Steering Fluid To check the power steering fluid do the following 1 Turn the key off and let the engine compartment cool down 2 Remove engine oil fill cap 3 Slide engine cover rearward and lift to remove 4 Wipe the cap and the top of the reservoir clean 5 Unscrew the cap and wipe the dipstick with a clean rag 6 Replace the cap and completely tighten it 7 Remove the cap again and look at the fluid level on the dipstick The fluid level should be within the area indicated on the dipstick when the engine is cold What to Use To determine what kind of fluid to use Recommended Fluids and Lubricants on page 6 13 Always use the proper fluid Notice Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle s warranty Always use the correct fluid listed in Recommended Fluids and Lubricants on page 6 13 Service and Appearance Care Windshield Washer Fluid What to Use When you need windshield or rear window washer fluid be sure to read the manufacturer s instructions before use If you will be operating your vehicle in an area where the temperature may fall below f
425. xterior lamps and lenses Follow instructions under Washing Your Vehicle on page 5 75 5 76 Service and Appearance Care Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish Approved cleaning products can be obtained from your dealer retailer If the vehicle has a basecoat clearcoat paint finish the clearcoat gives more depth and gloss to the colored basecoat Always use waxes and polishes that are non abrasive and made for a basecoat clearcoat paint finish Notice Machine compounding or aggressive polishing ona basecoat clearcoat paint finish may damage it Use only non abrasive waxes and polishes that are made for a basecoat clearcoat paint finish on the vehicle Foreign materials such as calcium chloride and other salts ice melting agents road oil and tar tree sap bird droppings chemicals from industrial chimneys etc can damage the vehicle s finish if they remain on painted surfaces Wash the vehicle as soon as possible If necessary use non abrasive cleaners that are marked safe for painted surfaces to remove foreign matter Exterior painted surfaces are subject to aging weather and chemical fallout that can take their toll over a period of years To help keep the paint finish looking new keep the vehicle garaged or covered whenever possible Protecting Exterior Bright Metal Parts Bright metal parts should b
426. y crash may have been stressed or damaged See your dealer retailer to have the safety belt assemblies inspected or replaced If the vehicle has the LATCH system and it was being used during a crash you may need new LATCH system parts 1 59 New parts and repairs may be necessary even if the safety belt or LATCH system if equipped was not being used at the time of the crash If an airbag inflates you will need to replace airbag system parts See the part on the airbag system earlier in this section Have the safety belt pretensioners checked if the vehicle has been in a crash if the airbag readiness light stays on after the vehicle is started or while you are driving See Airbag Readiness Light on page 3 29 1 60 Seats and Restraint System 4 NOTES Features and Controls Keys KGYS darenn rieien 2 2 Remote Keyless Entry RKE System 2 3 Remote Keyless Entry RKE System Operation 2 4 Remote Vehicle Start 2 5 Doors and Locks Door LOCKS sscssnaiewsgeceadeseacckus 2 7 Power Door Locks 2 8 Delayed Locking seese 2 8 Automatic Door Lock 2 8 Automatic Door Unlock 2 8 Rear Door Security Locks 2 8 Lockout Protection 2 8 Liftgate ioe cscicecassccdinneetenactensant 2 9 Windows WINGOWS sceesceesceeseeeseeeeuues 2 10 Power Windows seeseeeeees 2 10 SUN ViISOLS seecceeeeeeeeeeeeeeee
427. ys There are no road signs posted speed limits or signal lights Use good judgment about what is safe and what is not Driving on Hills Off road driving often takes you up down or across a hill Driving safely on hills requires good judgment and an understanding of what the vehicle can and cannot do There are some hills that simply cannot be driven no matter how well built the vehicle Z CAUTION Many hills are simply too steep for any vehicle If you drive up them you will stall If you drive down them you cannot control your speed If you drive across them you will roll over You could be seriously injured or killed If you have any doubt about the steepness do not drive the hill Approaching a Hill When you approach a hill decide if it is too steep to climb descend or cross Steepness can be hard to judge On a very small hill for example there may be a smooth constant incline with only a small change in elevation where you can easily see all the way to the top Ona large hill the incline may get steeper as you near the top but you might not see this because the crest of the hill is hidden by bushes grass or shrubs Consider this as you approach a hill e ls there a constant incline or does the hill get sharply steeper in places e ls there good traction on the hillside or will the surface cause tire slipping Driving Your Vehicle 4 17 e Is there a straight path up o
428. ys follow the maintenance schedule in this manual for changing engine oil GA The oil pressure light should come on briefly as the engine is started If it does not come on have the vehicle serviced by your dealer retailer If the light comes on and stays on it means that oil is not flowing through the engine properly The vehicle could be low on oil and might have some other system problem 3 38 Instrument Panel Change Engine Oil Light taa When the change engine oil light comes on it means that service is required on the vehicle See Scheduled Maintenance on page 6 3 and Engine Oil on page 5 14 for more information After the engine oil is changed the engine oil life system needs to be reset in order to turn off this light See Engine Oil Life System on page 5 16 for more information Security Light a For information regarding this light and the vehicle s security system see PASS Key Ill Electronic Immobilizer on page 2 13 Fog Lamp Light 0 The fog lamp light comes on when the fog lamps are in use The light goes out when the fog lamps are turned off See Fog Lamps on page 3 14 for more information Cruise Control Light The cruise control light comes on whenever the cruise control is set The light goes out when the cruise control is turned off See Cruise Control on page 3 9 for more information Reduced Engine Power Light i The reduced engine power light should

Saturn 2009 VUE Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents