Sanyo TLS-224P VCR User Manual
Contents
1. 9 19 10 20 ar Month Day Press the w or A button to set the day of the holiday then press the button Press the w or A button to set the month of the Press the or 4 button the next line to set starts O Repeat steps to to set up to 20 holidays Press the PAUSE SCAN button the normal screen is displayed O The setting procedure is now completed e If setting holidays be sure that a timer recording is set for Sunday If not this function will not operate 18 Changing a Programme Timer Recording O Press the AUDIO ON MENU button until the TIMER SET menu is display Press the or 4 button until the setting to correct is flashing Press the v or a button to correct the setting Press the PAUSE SCAN button the normal screen is displayed O Press the TIMER button To Cancel a Programme Timer Recording O Press the AUDIO ON MENU button until the TIMER SET menu is displayed Press the or 4 button until the Y corresponding to the timer recording to cancel is flashing Press the w or a button to select N O Press the PAUSE SCAN button the normal screen is displayed O Press the TIMER button To Cancel all Programme Timer Recordings Press the AUDIO ON MENU button until the TIMER SET menu is displayed Press the MENU RESET button O All programmed timer recordings are erased O Press the2. Example 1 To record on every Saturday from 9 00 AM to 5 00 PM 17 00 in 24 hour mode recording speed Make sure that the set date and time are correct Load a cassette tape with erasure prevention tab Press the AUDIO ON MENU button until the TIMER SET menu is displayed o SUN Sunday will be flashing 000 lt TIMER START SET gt STOP EKKEK iii ZZZZZZZZZ Press the 4 button until SAT Saturday is flashing Press the button O The recording start hour position starts flashing Press the w or A button to set the recording start hour ex 09 then press the button O The recording start minutes position starts flashing Press the w or A button to set the recording start minutes ex 00 then press the button O The recording stop hour position starts flashing Press the w or A button to set the recording stop hour ex 17 then press the button O The recording stop minutes position starts flashing NOTE e f the set stop time is earlier than or the same time as the set start time the VCR will consider the stop time to be the following day and T will be displayed next to the recording stop time English 17 Press the v or a button to set the recording stop minutes ex 00 then press the button O The SPD recording speea position will start flashing Press the w or a button to se
3. Press the TIMER button to display the digital display N is selected for the timer recordings Be sure to select Y for the programmed timer recordings Alarm recording is not possible OFF is displayed on the digital display Press the EJECT STOP FF REW or PLAY button to turn the indicator off Noise in the playback picture The video heads need cleaning Clean the video heads The date and time are not recorded The ON SCREEN switch is set to the OFF position Set the ON SCREEN switch to the ON position The cassette tape cannot be ejected After a Power Failure If after a power failure the recording speed is reset to 3 hour mode it is due to insufficient backup battery o charge This is not a malfunction Problem with the system Turn the power off then on again System Down If the unit does not function at all try the following Unplug the power cord then plug it back in Reset the memory Press the ALL RESET button Under normal conditions do not touch the ALL RESET button If the problem is not corrected after performing steps and a few times consult your dealer 28 English SPECIFICATIONS General Specifications Recording method Audio recording Tape speed Specified video cassette tape Recording playback time Fast forward rewind time Standard Video Recording method Video input Video output Horizont
4. 5V H Output impedance 5 7 kQ OV L NOTE e f the output is OV Low due to the clog detect function it can be reset by simply pressing the STOP button COM Terminal e Common GND ground terminal when connecting other terminals to external devices OUTPUT TERMINALS SW OUT Terminal When recording a pulse signal is output at the SW OUT terminal This terminal is usually connected to the switch input SW IN of devices like a camera switcher unit or a quad compressor 5V H Output impedance 5 7 KQ OV L SW OUT Terminal Output Setting O Press the AUDIO ON MENU button until the SET UP 4 menu is displayed O The FIELD or FRAME setting is flashing lt SET UP 4 gt SW OUT FIELD 01 TIMING FIELD 3H Y lt USED TIME gt El VIDEO POWER 00000H 00000H NOTE e If TIMING is set to FRAME see step O FRAME will be indicated instead of FIELD Press the w or A button to set the pulse signal interval Available settings are FIELD 01 02 03 04 05 10 30 or 60 field FRAME 01 02 03 04 05 10 30 or 60 frame Press the 4 button to select the output timing O Press the v or a button to set FIELD or FRAME FIELD 1 pulse is output after each set number of fields FRAME 1 pulse is output after each set number of frames Press the J button o The 3H setting starts flashing Press th
5. ALARM IN The buzzer will be heard during alarm recording TAPE END The buzzer will be heard when the end of the tape is reached during recording KEYIN The buzzer will be heard when one of the VCR buttons is pressed O Press the PAUSE SCAN button the normal screen is displayed O The setting procedure is now completed English 23 CHECKING USAGE DURATION O Press the AUDIO ON MENU button until the USED Example TIME menu is displayed SET UP 4 gt SW OUT USED TIME The video heads usage FIELD SERA duration and the power 3H Y on duration are EERS displayed VIDEO 00003H POWER 00007H Press the PAUSE SCAN button the normal screen is displayed NOTE e The USED TIME data cannot be reset CHECKING POWER FAILURE AND FAILURE DUE TO CONDENSATION O Press the AUDIO ON MENU button until the Example POWER FAILURE and DEW menu is displayed lt POWER FAILURE gt 002 FAILURE 11 10 07 15 POWER FAILURE The number of power RECOVERY 11 10 07 30 failures and the date lt DEW gt and time of the most 001 FAILURE 10 10 11 00 RECOVERY 10 10 12 00 recent power failure and recovery are displayed DEW The number of failures due to condensation and the date and time of the most recent failure and recovery are displayed Press the PAUSE SCAN button the normal screen is displayed NOTE O f the MENU RESET button is pressed while the POWER FAILU
6. For accurate clock setting press the w button timed with a time broadcast or other accurate time signal this will start the seconds counting from 00 lt SET UP 1 gt SUMMER TIME SET USE WEEK MONTH TIME ON LST SUN 03 02 00 OFF LST SUN 10 02 00 CLOCK SET 15 10 99 FRI 15 20 00 LANGUAGE ENGLISH When finished press the PAUSE SCAN button to save the settings English CHANGING THE ON SCREEN DISPLAY Selecting the On screen Display You can select to display or not the date time the number of alarm triggers and tape speed Turn the power on to all devices used Press the AUDIO ON MENU button until the SET UP 2 menu is displayed lt SET UP 2 gt DISPLAY ALARM COUNT SPEED BUZZER ALARM IN TAPE END KEY IN O Press the 4 button until the desired item for which the display function will be set is flashing Press the v or a button to set Y for the functions described below DATE The date is displayed TIME The time is displayed ALARM COUNT The number of alarm triggers is displayed SPEED The recording playback speed is displayed O Press the PAUSE SCAN button the normal screen is displayed O The setting procedure is now completed NOTE e If the ON SCREEN switch is set to the ON position the items for which Y is set are recorded The items for which N was set at step above are not recorded English Changing
7. Digital display panel LOCATIONS OF CONTROLS AND INDICATORS Digital Display Operation Indicators e They display the actual operation mode Operation Mode Indicator Record REC Record pause REC PAUSE HA Playback PLAY Still image STILL 1 Fast forward FF Rewind REW Y O Alarm indicator Flashes when an alarm is being recorded AL Cue CUE Y N Review REVIEW Comes on after the alarm has been recorded AL Field shift forward FIELD SHIFT e Clog detection indicator 2 Error indicator ER l l l c i bl Flashes when the recording quality deteriorates omes on in case of a problem due to dirty VCR heads O Power failure indicator P Q OFF indicator OFF Comes on after a power failure Comes on when the tape end has been reached Ma after a recording except during autorepeat 4 External input indicator E recording mode Comes on when recording using the EXT TIMER IN NOTE input terminal i a J e The buzzer will be heard as long as OFF is 5 Timer Recording indicator displayed on the digital display Comes on when in timer recording stand by mode To cancel the OFF display press the EJECT or during a timer recording PLAY STOP FF or REW button Security lock indicator l Cassette indicator oe Comes on when the security lock is engaged Comes on when a cassette is loaded D cone display A D Mode display i Time display Pere dee e Recording playback m H LOLI LIL
8. lt SET UP 3 gt ALARM MODE Y1 ALARM SPEED ALARM DURATION TAPE IN MODE TAPE END MODE TAPE END OUT CLOG DETECT Press the w or A button to set the desired alarm mode then press the Y button Alarm recording is done when there is an alarm trigger Alarm recording is done only when there is an alarm trigger during programmed timer recording Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode Alarm recording is not performed even if there is an alarm trigger Press the w or A button to set the desired alarm recording speed then press the J button EE aes 3 hour mode recording 12H 12 hour mode recording NC Recording at the speed already set 14 Press the v or a button to select the desired alarm recording duration 20S 40S 1M 2M 3M 5M CC or TRIG 20S 5M Recording only for the displayed duration CC Recording as long as the alarm signal is being input minimum recording of 5 seconds TRIG Will switch between recording pause and recording every time an alarm trigger is received during recording O Press the PAUSE SCAN button the normal screen is displayed O The setting procedure is now completed NOTES During alarm recording all buttons are disabled e f OFF is displayed on the digital display alarm recording is not possible in order to prevent the recorded tape to be recorded
9. the tape counter indication is a ratio of the 3 hour mode base indication In 12 hour recording mode each second of the tape counter actually represents approximately 12 3 1 5 real seconds e There may be a slight discrepancy between the position shown on the tape counter and the actual tape position e When rewinding the tape past the 0 00 00 position a minus sign will be displayed Record Pause Recording can be interrupted temporarily O Press the PAUSE SCAN button during recording O The Pause Still indicator m blinks NOTES e The image appears on screen but it is not recorded e If a recording pause continues for 5 minutes or more the VCR will go into stop mode to avoid damaging the tape To resume recording press the REC button or press the PAUSE SCAN button again NORMAL RECORDING Recording Check Clog Detection The image being recorded can be checked This VCR is equipped with a clog detection function During recording press the PLAY REC CHECK The recording quality is monitored automatically When button the heads are dirty and the recording quality deteriorates the output at the WARNING OUT terminal becomes OV Low the 0 indicator flashes on the digital display and the buzzer sounds If in the SET UP 3 menu CLOG DETECT is set to NOTE N the recording quality is not monitored O The tape will be rewound and then played back The VCR will then ret
10. L speed mode e Alarm scan mode AL e Linear time counter ren ened meio oe AL IN ALELLA e Dew display TE Vd gt A e Id LI N N O 4 English LOCATIONS OF CONTROLS AND INDICATORS Back Panel DOLOODOQ WARNING TAPE SW ALARM UM eaa dd DC12V IN eldjeleje DC12V IN e GED 4948 VIDEO IN video input jack ap VIDEO OUT video output jack 2 AUDIO IN audio input jack 13 AUDIO OUT audio output jack MIC IN microphone input jack D REMOTE remote control input jack DC 12 V IN DC 12 V input jack D DC 12 V IN input terminal O Battery compartment cover 2 EXT TIMER IN external timer input terminal 8 COM common terminal D WARNING OUT warning output terminal 6 TAPE END OUT tape end output terminal SW OUT switch output terminal D COM common terminal ALARM OUT alarm output terminal 9 ALARM IN alarm input terminal Do not use DC 12 V IN input terminal 20 Fuse cover NOTES e This terminal board may be damaged by 5 kg cm or more torque and using 66 mm tip or more size screwdrivers O Pay attention to the polarity of the DC 12 V input terminal red screw black screw e When both the DC 12 V IN jack and the DC 12 V IN terminals are connected the input with the highest voltage will have priority English 5 CONNECTIONS Connect the video camera and monitor TV as shown in the figure below NOTE Before maki
11. PAUSE SCAN button the normal screen is displayed English PROGRAMME TIMER RECORDING NOTES e During timer recording or timer recording stand by all the buttons on the VCR except the TIMER button are disabled e f the power fails the recording will be interrupted When the power is restored the recording will resume if the stop time has not yet been reached and P will be displayed on the digital display The VCR internal battery is completely recharged after the VCR has been connected to a live outlet for 48 hours and it will maintain all the VCR settings memory for up to 30 days O Set the timer recordings so that the recording times do not overlap lf they do the one with the earliest recording start time will have priority See chart below 7 00PM 8 00PM 9 00PM 10 00PM Programme 3 These portions will not be recorded e To set two or more timer recordings for a same day of the week press the or 4 button until the day of the week for the second recording is flashing then press the w or A button to set the desired day of the week e If no timer recording is set or a cassette without erasure prevention tab is loaded when the TIMER button is pressed the timer recording indicator E will start flashing and a buzzer will be heard e f OFF is displayed on the digital display timer recording is not possible in order to prevent the recorded tape to be recorded
12. control to correct 22 English SETTING THE SECURITY LOCK The security lock function is designed to prevent NOTES accidental stopping of recording ifthe STOP button is i e While the security lock is engaged all commands pressed inadvertenly except the one to cancel the security lock are While holding the TRACKING V STILL button disabled press the REC PLAY SPEED button e The security lock cannot be engaged while a menu is o 1 is displayed on the digital display displayed To cancel the security lock while holding the TRACKING V STILL button press the REC PLAY SPEED button 1 will be erased from the digital display E SETTING THE BUZZER If desired a buzzer can warn you when an alarm NOTES recording is taking place when the tape has reached e f N is set the buzzer will not be heard the end or when buttons are being pressed on the VCR e During timer recording mode security lock engaged Press the AUDIO ON MENU button until the SET mode and alarm recording mode the buzzer will not UP 2 menu be heard when a button related to one of these modes is pressed even if Y is set for the KEY IN lt SET UP 2 gt item DISPLAY DATE TIME ALARM COUNT SPEED BUZZER ALARM IN TAPE END KEY IN Press the 4 button until the desired item for which the buzzer function will be set is flashing Press the w or a button to set Y for the functions described below
13. is received and the unit is recording the output falls to OV Once the alarm recording is over the output returns to DC 5V English 15 Checking the Alarm Recordings Time Press the AUDIO ON MENU button until the ALARM TIME menu is displayed o The number of alarm triggers and the 8 most recent alarm recording times are displayed Example lt ALARM TIME gt 008 12 12 12 11 12 11 11 10 11 10 10 09 10 09 10 09 NOTE e The data for the previous alarm recordings is erased O Press the PAUSE SCAN button the normal screen is displayed NOTE O f the MENU RESET button is pressed while the ALARM TIME menu is displayed the displayed data is erased AL will be erased from the digital display ALARM RECORDING Alarm Scan To look for an alarm recording by viewing the first 5 seconds of each alarm recording O Press the PAUSE SCAN button during stop mode O AL SCAN will be displayed on screen Press the FF or REW button O The unit will advance or rewind the tape at high speed and playback the first 5 seconds of every alarm recording O To cancel the alarm scan mode press the STOP button While the desired recording is being played back press the PLAY button O Playback will start alarm scan mode is cancelled 16 English PROGRAMME TIMER RECORDING There are two programme timer recording methods daily recording or recording on certain days of the week
14. u ze niet weggooien maar inleveren als KCA FEATURES CONTENTS e Clog detection e High speed Fast forward Rewind e Field recording playback e 3 12 24 hour mode recording audio playback e Autorepeat recording e Alarm recording function e On screen mode setting e Integrated time date generator e Alarm scan function e Forward field advance function e 30 day memory backup e Security lock e Recording check function e Head cleaning function What is Time Lapse Video A standard VCR records 50 images fields per second while this time lapse VCR can record at different rates This feature makes it possible to record up to 27 hours on a single video tape As a result this unit is extremely useful for long term monitoring or recording changes that take place slowly over an extended period of time such as the blooming of a flower PRECAUTIONS 0 00 00 eee eee 1 PEA TURES cucuta ral Gates Gated med 2 LOCATIONS OF CONTROLS AND INDICATORS cocccccccc EE ee ee ee 3 CONNECTIONS a ee ee SE ee ee ee 6 TYPES OF ON SCREEN DISPLAYS AND DISPLAY SEQUENCE ee ee ee ee 7 SETTING THE LANGUAGE AND CLOCK 8 CHANGING THE ON SCREEN DISPLAY 9 VIDEO CASSETTE TAPES 04 10 NORMAL RECORDING 0 00005 11 AUTOREPEAT RECORDING 13 ALARM RECORDING ee se se ee ee ee 14 PROGRAMME TIMER RECORDING 17 RECORDING USING AN
15. will continue to the end of the tape then it will be rewound to the beginning and stop OFF will be displayed on the digital display English 13 Setting the Mode at the End of the Tape In the SET UP 3 menu you can set the mode of the VCR mode when the tape reaches the end during recording O Press the AUDIO ON MENU button until the SET UP 3 menu is displayed lt SET UP 3 gt ALARM MODE ALARM SPEED ALARM DURATION TAPE IN MODE TAPE END MODE TAPE END OUT CLOG DETECT Press the 4 button until the TAPE END MODE setting is flashing Press the v or a button to set the desired mode REW Rewinds the tape to the beginning then goes to stop mode STOP cuid Goes to stop mode EJECT The cassette is ejected Rissen draa The autorepeat mode is automatically canceled if there was an alarm trigger Rea ads ara Autorepeat mode is active even if there was an alarm trigger Press the PAUSE SCAN button to save the setting ALARM RECORDING By connecting the ALARM IN terminal to a door switch an interphone etc a recording can be done only when necessary Alarm Recording Setting Alarm recording is performed when there is an input trigger at the ALARM IN terminal AL is displayed on the digital display Make all necessary connections Press the AUDIO ON MENU button until the SET UP 3 menu is displayed o The ALARM MODE setting is flashing
16. EXTERNAL TIMER INPUT 20 NORMAL PLAYBACK 0000 00 00 21 SPECIAL PLAYBACK 0 ee ee ee 22 SETTING THE SECURITY LOCK 23 SETTING THE BUZZER 000 4 23 CHECKING USAGE DURATION 24 CHECKING POWER FAILURE AND FAILURE DUE TO CONDENSATION 24 OUTPUT TERMINALS 000000 25 MAINTENANCE 0 000000 e eee eee 27 TROUBLESHOOTING GUIDE 28 SPECIFICATIONS ooo 29 English LOCATIONS OF CONTROLS AND INDICATORS Front Panel 0000 Y OOM STANDBY ON e REPEAT l SCAN ON ON SCREEN STANDBYION ON OFF REW gt FF TRACKING VSTILL REC PLAY AUDIO ON SPEED TIMER O EJECT button 2 Cassette loading slot 3 PAUSE SCAN button 4 REW rewind review button 5 PLAY REC CHECK button FF fast forward cue button D STOP button REC record button 9 STANDBY ON LED REPEAT LED autorepeat recording indicator English ED ES sd QD MENU RESET button 2 ALL RESET button 3 TIMER button RECIPLAY SPEED button recording playback speed 1 TRACKING V STILL button TRACKING V STILL button 17 AUDIO ON MENU button Press this button to display the menu Buttons 40 and 46 are used for menu control ON SCREEN switch STANDBY ON button 20 Front door 21
17. Fire e Do not handle the power cord with wet hands e Do not pull on the power cord e If any liquid is spilled on the VCR unplug the power cord immediately and have the unit inspected at a factory authorised service centre e Do not place anything directly on top of this VCR English CAUTION Do not put your hand or other objects in the cassette loading slot because of risk of injury or accident Be sure to keep small children away from the VCR Moisture Condensation Problems Cause When the VCR is first installed moved from a cold area to a warm area or placed in a location with high humidity dew moisture may form in the unit The Dew N indicator cca blinks If you operate the VCR with dew inside damage may result Prevention Make al necessary connections Plug the power cord Do not operate the VCR for approximately 2 hours When the VCR reaches room temperature the Dew indicator dd dd will turn off and the VCR will be ready to operate Power on stand by mode The power on stand by mode is selected by pressing the STANDBY ON button VCR display Stand by mode Power on mode Stand by mode is the condition in which only the time is displayed Do not forget that even in the stand by mode there is an electrical voltage inside the VCR Disconnect the power cord if the VCR is not to be used for a long time Bij dit produkt zijn batterijen geleverd Wanneer deze leeg zijn moet
18. O Turn the power on to all devices used Load a cassette tape with erasure prevention tab NOTE e If in the SET UP 3 menu TAPE IN MODE is set to REC recording will start Set the ON SCREEN switch to the ON position Press the REC PLAY SPEED button to set the recording speed o The recording speed is displayed on screen and on the digital display Press the REC button O The Record indicator 0 lights O Recording starts To stop recording press the STOP button NOTES O A tape recorded on this VCR cannot be played back on a time lapse VCR produced by another manufacturer e f you press on the REC button and the loaded cassette has no erasure prevention tab the VCR will eject the cassette e During recording the AUDIO ON MENU button will not function the menu cannot be displayed e During recording the tape speed cannot be changed English 11 Recording Speed Maximum recording duration with an E 180 cassette tape Audio recording Recording speed Recording interval Tape motion Standard mode Time lapse mode TAPE COUNTER NOTES e There is no tape counter indication for the blank portions of the tape 3 12 1 50 second 0 1 0 18 3 hours 15 27 Possible Continuous e In the 3 hour recording speed mode only the tape counter indicates real hours minutes and seconds e In the other recording speed modes
19. PES OF CLEANERS THESE CHEMICALS CAN CRACK OR DISCOLOR THE CABINET TROUBLESHOOTING GUIDE If the unit does not operate normally when you follow the instructions indicated in the manual please refer to the table below SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION No power The power cord is not connected Connect the power cord No image displayed on the monitor TV The connections are not correct Check that all connections are correct The power to the camera and or monitor TV is not turned on Turn all connected devices power on The buttons do not respond A cassette tape is not loaded Load a cassette and turn the power on All functions are suspended due to condensation Wait for the gg ag indicator to go off Alarm recording Wait for the alarm recording to end The security lock is engaged Cancel the security lock Recording is not possible the tape is ejected The loaded cassette has no erasure prevention tab Load a cassette tape with erasure prevention tab or cover the tab hole with adhesive tape Autorepeat recording is not possible AL is displayed on the digital display Display ALARM TIME menu then press the MENU RESET button to turn off the AL indicator Timer recording is not possible The date and time are not set correctly Set the date and time correctly The unit is not set to timer recording stand by mode
20. RE and DEW menu is displayed the data is erased P will be erased from the digital display 24 English OUTPUT TERMINALS TAPE END OUT Terminal During recording when the end of the tape is reached or when the tape counter reading indicates 2 hours 57 minutes or more the output becomes OV Low e During autorepeat recording when the end of the tape is reached the output become OV Low for about 2 seconds only e To reset the output press the STOP or EJECT button Tape end or 2H57M00s Output reset i y 5V H Output impedance 5 7 kQ OV L TAPE END OUT Terminal Output Setting Press the AUDIO ON MENU button until the SET UP 3 menu is displayed lt SET UP 3 gt ALARM MODE Y1 ALARM SPEED ALARM DURATION TAPE IN MODE TAPE END MODE TAPE END OUT CLOG DETECT O Press the 4 button until the TAPE END OUT setting is flashing Press the v or a button to select the desired output mode The output become 0 V Low when the tape counter reaches 2 57 00 and or when the tape reaches the end The output become 0 V Low when the tape reaches the end O Press the PAUSE SCAN button the normal screen is displayed English 25 WARNING OUT Terminal e f the tape stops or other problem the output becomes OV Low e To reset the output unplug the power cord then plug it back in or press the ALL RESET button Tape movement stop Output reset y
21. SANYO INSTRUCTION MANUAL TLS 224P Time Lapse Video Cassette Recorder English Time Lapse Videorecorder Deutsch Magn toscope time lapse a cassette Francais Videograbador en lapsos de tiempo Espa ol Videoregistratore a cassette a fotogrammi differenziati ellano de fa Hy By HE Re RAL wn PRECAUTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only If the power supply cord power cord of this appliance is damaged it must be replaced Location For safe operation and satisfactory performance of your VCR keep the following in mind when selecting a place for its installation e Shield it from direct sunlight and keep it away from sources of intense heat e Avoid dusty or humid places e Avoid places with insufficient ventilation for proper heat dissipation Do not block the ventilation holes of the VCR Do not place the unit on a carpet because this will block the ventilation holes e Install the VCR in a horizontal position only e Avoid locations subject to strong vibrations e Avoid moving the VCR between cold and hot locations see Moisture Condensation Problems this page e Do not place the VCR directly on top of the TV as this may cause playback or recording problems Avoiding Electrical Shock and
22. al resolution Audio Input Output Microphone input Connectors Alarm input Alarm output Tape end output Warning output Switch output Ext timer input DC 12 V input DC 12 V input Common Remote control input DC 12 V input Other Specifications Operating temperature range Operating humidity range Power requirements Power consumption Dimensions Weight Dual azimuth 2 head rotating helical scanning system In 3 12 and 24 hour modes 23 39 mm sec 3 hour mode VHS 1 2 inch 3 12 and 24 hours when using E 180 tape approximately 2 minutes 45 seconds when using E 180 tape CCIR PAL colour Luminance signal FM recording Chrominance signal Down converted direct recording 1 Vp p BNC 75 Q unbalanced 1 Vp p BNC 75 Q unbalanced Black amp white mode 350 line or more Colour mode 250 line or more 8 dBs RCA pin jack 27 KO unbalanced 8 dBs RCA pin jack 600 Q unbalanced 60 dBs 3 5 mm mini jack 10 kQ unbalanced Low level active OV DC 5 V 0 5 5 7 kQ Low at alarm DC 5 V 0 5 5 7 kQ Low at tape end DC 5 V 0 5 5 7 kQ Low at warning DC 5 V 0 5 5 7 kQ Low at switching Low level active OV DC 12 V DC OV 0 V GND 3 5 mm mini jack Mini jack 5T to 40C 80 or less DC 12 V 10 V to 16 V 14W 240 W x 96 5 H x 335 D mm approximately 3 8 kg NOTE The specifications and external appearance of this unit are subject to change without notice En
23. and hold the TRACKING V STILL button to reduce the vertical rolling of the image If it cannot be corrected press the TRACKING V STILL button Audio Playback e The playback speed has to be the same as the recording speed for normal playback of the audio e For a tape recorded in 12 hour and 24 hour recording modes to playback the audio press the AUDIO ON MENU button after pressing the PLAY button A will be displayed to the left of the playback speed on the digital display NOTE Noise will appear in the image when audio playback is used in 12 or 24 hour modes SPECIAL PLAYBACK Picture Search Frame Advance O Press the FF or REW button during normal O Press the FF button during still image mode playback O The still image is advanced of one image o The image can be seen while the tape is field AVANCER OF TOM DUNE AMON Speed To return to normal playback press the PLAY To return to normal playback press the PLAY button button NOTES During picture search noise horizontal bars will appear in the picture e The sound is muted Still Image Press the PAUSE SCAN button during normal playback OA still image can be viewed To return to normal playback press the PLAY button NOTES e If still mode continues for 5 minutes or more the VCR will go into stop mode to avoid damaging the tape e f the image is unstable rolling vertically adjust the vertical lock
24. annot be displayed e To reset the settings of a menu to their original values select the desired menu then press the MENU RESET button The USED TIME menu data cannot be reset e To enter the settings use the 1 v or A buttons Buttons functions Button 4 To move down Button To move to the right Button w To select numbers or switch settings in reverse order Button a To select numbers or switch settings in order Monitor TV screen normal screen 15 10 99 FRI 00 15 20 00 0 3 Set the ON SCREEN switch to the ON position Press the AUDIO ON MENU button First time SET UP 1 menu SET UP 1 gt To set the summer standard time SUMMER TIME SET eTo set the date time eTo select the display language TIMER SET menu lt TIMER SET gt eTo set timer recordings CLOCK SET LANGUAGE Press the AUDIO ON Press the PAUSE SCAN button MENU button O Ohi Press the PAUSE SCAN button MENU button Second time Sixth time SET UP 2 menu HOLIDAY SET menu lt SET UP 2 gt eTo set the on screen display lt HOLIDAY SET gt To set the holidays DISPLAY eTo set the buzzer BUZZER Press the Press the AUDIO ON Press the PAUSE SCAN button AUDIO ON Press the PAUSE SCAN button MENU button MENU button Third time Seventh time SET UP 3 menu POWER FAILURE DEW menu A SET UP 3 gt To set the alarm recording POWER FAILURES To display the number and To set vario
25. e v or A button to set the 3H A EE a When recording in 3 hour mode a pulse signal is output Ne tie aA e When recording in 3 hour mode a pulse signal is not output Press the PAUSE SCAN button the normal screen is displayed 26 REMOTE Jack e You can use a VA RMNO1 Remote Control Unit sold separately to control remotely the VCR e Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below to the REMOTE jack NOTES e Use a 3 5 mm mini jack type plug e The connection should be done using a shielded cable no more that 5 meters long Remote control circuit R1 1 5K SW1 STOP R2 0 43K SW2 PAUSE STILL R3 0 51K SW3 REW R4 0 62K SWA FF R5 0 75K SW5 PLAY R6 0 91K SW6 REC R7 1 1K SW7 MENU R8 1 3K SW8 Do not use R9 2 0K SW9 TIMER A R10 2 4K SW10 REC PLAY SPEED Y R11 3 6K SW11 TRACKING V STILL 4 R12 5 6K SW12 TRACKING V STILL gt The resistance tolerance is 2 or less NOTES e The functions not available on the VCR will not operate e The REC PLAY SPEED a button on the VA RMNO1 will function as the TIMER button on the VCR English MAINTENANCE Daily Inspection The following daily inspections are recommended in order to assure long term and trouble free operation of the unit The daily inspections are particularly important if using autorepeat recording Inspection Procedure O Turn on the po
26. g slot Gently push the centre of the cassette until it is loaded automatically O When the cassette is loaded the cassette indicator ee will light on the digital display O The time display will switch to the reset counter 0 00 00 display NOTE e If you try to record on a cassette without erasure prevention tab the VCR will eject the cassette Unloading In STOP mode press the EJECT button O The cassette is automatically ejected NOTES e Do not insert any object in the cassette loading slot as that may cause injury and damages to the VCR e If your hand gets stuck in the cassette loading slot unplug the power cord and consult the dealer where the unit was bought Do not forcibly pull the hand out as that may cause severe injuries Setting the Action to Take When a Cassette is Loaded In the SET UP 3 menu you can set the mode the VCR will go into when a cassette is loaded O Press the AUDIO ON MENU button until the SET UP 3 menu is displayed lt SET UP 3 gt ALARM MODE ALARM SPEED ALARM DURATION TAPE IN MODE TAPE END MODE TAPE END OUT CLOG DETECT Press the Y button until the TAPE IN MODE setting is flashing Press the w or a button to set the desired mode STOP Stays in stop mode REC Goes into recording mode Press the PAUSE SCAN button to save the setting English NORMAL RECORDING Normal Recording 0
27. glish 29 SANYO SANYO Electric Co Ltd 1ACGP1P1668 A NE4OG EX 0598KP SYO1 Issue No 1 Copyright SANYO 1998 All rights reserved Printed in Japan
28. ill take place NOTES e Other timer recordings using the standard procedure can also be programmed e When there is a signal being input at the EXT TIMER IN terminal E will be displayed on the digital display and recording is conducted English NORMAL PLAYBACK Normal Playback O Turn on the power to the VCR and TV monitor Load the video cassette tape Press the REC PLAY SPEED button to select the playback speed o The selected playback speed is displayed on the digital display NOTE e A slow motion effect or accelerated playback effect can be achieved by using a slower or faster playback speed than the speed used for recording Press the PLAY button O Playback starts O If necessary adjust the tracking to eliminate the noise from the picture To stop playback press the STOP button O To advance or rewind the tape press the FF or REW button NOTES A tape recorded on a time lapse VCR produced by another manufacturer can not be played back on this unit O A tape recorded on this VCR cannot be played back on a time lapse VCR produced by another manufacturer English 21 Tracking Control If there is noise in the image during playback While looking at the playback picture press and hold the TRACKING V STILL button to minimize the noise It it cannot be minimized press the TRACKING V STILL button Vertical Lock Control During still image mode O Press
29. lect the recording speed ex 24 then press the button O N will start flashing Press the w or a button to select Y recording will take place recording will not take place lt TIMER SET gt START STOP N N N N N N Y N N O Repeat steps O to to programme timer recordings for other days of the weeks Press the PAUSE SCAN button the normal screen is displayed Press the TIMER button O The timer recording indicator EI will light on the digital display the VCR is now in timer recording stand by mode NOTES To modify cancel or stop timer recording press the TIMER button to cancel the timer recording mode e A timer recording of more than 24 hours can only be set on the 7th and 8th lines On the 7th line set the recording start time and set amp for the rest of the line On the 8th line set for the START time position then set the recording stop time recording speed and select Y or N e To record everyday at the same time at step select the DLY line PROGRAMME TIMER RECORDING Setting the Holidays By setting the holidays timer recording will be conducted on those days as set for Sundays O Press the AUDIO ON MENU button until the NOTE HOLIDAY SET menu is displayed lt HOLIDAY SET gt 8 18 4 14 5 15 6 16 7 17 8 18
30. ng the connections make sure all the devices are disconnected from the DC power supply Monitor TV sold separately Video camera sold separately From an external audio source 000001 un elelalajo DC12V IN REMOTE MIC IN ou To VIDEO OUT jack DC power cord not supplied L A To To Coaxial cable ACtoDC Remote sold separately To adaptor control DC power sold sold supply separately separately About the memory reset NOTES Ifthe VCR location is changed or to cancel previous O For more details please refer to the manuals settings please reset the memory as described below accompanying all other devices If the connections are not made properly it may cause a fire or damage the equipment e Use a DC power cord rated A W G 16 1 3 mm or more of a maximum length of 6 m The time and date will be reset To reset the memory press the ALL RESET button e The DC power supply source should be able to supply 8 A or more If the power supply is not sufficient the VCR may not operate properly e You can use a VA RMNO1 Remote Control Unit sold separately to control remotely the VCR 6 English TYPES OF ON SCREEN DISPLAYS AND DISPLAY SEQUENCE NOTES e When a menu is displayed recording will not be possible O Press the PAUSE SCAN or AUDIO ON MENU button the setting procedure is now completed e During recording or playback the menus c
31. over English 19 RECORDING USING AN EXTERNAL TIMER INPUT Recording can be controlled by an external start stop signal input at the EXT TIMER IN terminal Example 2 To record using the signal input at the EXT TIMER IN terminal in 12 hour mode NOTE e External timer input recording can only be set on the 9th line EXT of the TIMER SET menu O Follow steps to under PROGRAMME TIMER RECORDING on page 17 lt TIMER SET WEEK START STOP SPD SUN MON TUE WED THU FRI SAT DLY EXT kke keEE 222222222 9th line Press the 4 button until EXT External setting is flashing O The SPD recording speed position will start flashing Press the v or a button to select the recording speed ex 12 then press the button O N will start flashing O Press the w or a button to select Y lt TIMER SET WEEK START STOP SPD SUN MON TUE WED THU FRI SAT DLY KREET lt ZZZZZZZZ Follow steps and under PROGRAMME TIMER RECORDING on page 17 o When an external signal is input E will light on the digital display and recording w
32. over To cancel the OFF display press the EJECT PLAY STOP FF or REW button e If an alarm trigger is received while alarm recording is in progress recording duration for the second alarm will be calculated from that point The alarm counter will register the alarm but it will not be found during an alarm scan search e f there is a power failure during alarm recording and the power is restored within the recording set duration alarm recording will continue e f the alarm scan function will be used to review the recordings set the recording speed to 3 hour mode and the recording duration to 20 seconds or more English ALARM RECORDING Alarm Recording Counter Display e During alarm recording AL will be flashing on the digital display e If the ON SCREEN switch is set to the ON position the number of alarms will flash on the monitor screen e The maximum display number of alarm triggers is 999 at the next alarm recording the counter will indicate 000 e When the ALARM TIME menu is displayed press the MENU RESET button to reset the alarm counter to 000 all the data of the ALARM TIME menu is reset Connections to the ALARM IN OUT Terminals e Alarm input signal Connect a make contact no voltage switch between the ALARM IN and COM terminals e Alarm output signal Normally DC 5V are output between the ALARM OUT and the COM terminals When an alarm input trigger
33. the Date Time Display Position O Turn the power on to all devices used Set the ON SCREEN switch to the ON position O The date and time are displayed Date Time display 15 10 99 FRI 000 15 20 00 24 Press the or 4 button O The display will move towards the right or the bottom NOTES e If the or 4 button is kept pressed for 1 second or more the display will move at a faster speed e The display position cannot be changed while recording VIDEO CASSETTE TAPES Use only video cassette tapes bearing the VHS logo This VCR was primarily designed for use with E 180 cassette tapes it is recommended to use E 180 VHS video cassette tapes for optimal performance Handling Cassette Tapes The cassette tapes should always be stored vertically in their cases away from high temperatures magnetic fields direct sunlight dirt dust and locations subject to mold formation Do not tamper with the cassette mechanism and never touch the tape with your fingers Protect the cassette tapes from shocks or strong vibrations To Protect your Recordings After having recorded a tape if you wish to keep the recording use a flathead screwdriver to break off the erasure prevention tab on the cassette To record again on a tape without erasure prevention tab cover the hole with adhesive tape Erasure prevention tab Loading O Place the cassette label side up in the loadin
34. time adjustment NO USE No summer time standard time adjustment made USE mica The auto summer time standard time adjustment is made Press the J button Set the day the summer time adjustment is made e Press the w or A button to set the week then press the button 1ST 2ND 3RD 4TH or LST first second third fourth or last O Press the w or A button to set the day of week then press the button SUN MON TUE SAT Sunday Monday Tuesday Saturday Press the w or a button to set the month the summer time adjustment is made then press the button 01 02 11 12 for January February November December Press the v or a button to set the time the summer time adjustment is made Press the 4 button Following the same procedure as above steps O to O set when the time is changed back from summer time to standard time Press the 4 button Press the w or a button to set the day ex 15 then press the button O The day of week is set automatically Press the w or A button to set the month ex 10 then press the button Press the v or A button to set the year ex 99 for 1999 then press the button O The last 2 digits only are displayed Press the w or a button to set the hours ex 15 for 3 PM then press the button D Press the w or a button to set the minutes ex 20 then press the button
35. urn to the previous recording mode e During recording check operations recording is NOTES suspended momentarily z e To cancel the 0 indicator display and reset the WARNING OUT terminal output press the STOP or co EJECT button e Clog detection is not possible if recording in 3 hour recording mode 12 English AUTOREPEAT RECORDING Autorepeat Recording The same tape can be recorded over many times Press the AUDIO ON MENU button until the SET UP 3 menu is displayed o The ALARM MODE setting is flashing lt SET UP 3 gt ALARM MODE Y1 ALARM SPEED ALARM DURATION TAPE IN MODE TAPE END MODE TAPE END OUT CLOG DETECT Press the J button until the TAPE END MODE setting is flashing Press the w or A button to set to R 1 or R 2 See Setting the Mode at the End of the Tape Press the PAUSE SCAN button the normal screen is displayed Oo The REPEAT LED will light O The setting procedure is now completed Press the REC button Recording will start When the tape end is reached the VCR will rewind it to the beginning and recording will resume NOTES e f during autorepeat recording there is an alarm trigger AL is displayed on the digital display and alarm recording will take place Please refer to page 14 ALARM RECORDING e lf the TAPE END MODE setting is R 1 the REPEAT LED will go off if there is an alarm trigger The recording
36. us VCR functions duration of power failures To display the number and duration of failures due to condensation Press the Press the PAUSE SCAN button AUDIO ON MENU button Fourth time SET UP 4 USED TIME menu SET UP 4 gt To set the SW OUT terminal SW OUT output Press the Press the PAUSE SCAN button AUDIO ON MENU button Eightth time ALARM TIME menu ALARM TIME eTo display the number and time of the alarms triggers lt USED TIME gt eTo display the time used Press the AUDIO ON Press the PAUSE SCAN button MENU button Fifth time Press the AUDIO ON Press the PAUSE SCAN button MENU button Ninth time English 7 SETTING THE LANGUAGE AND CLOCK Language Setting English French or German can be selected by the user Turn the power on to all devices used Press the AUDIO ON MENU button to display the SET UP 1 menu lt SET UP 1 gt SUMMER TIME SET NO USE WEEK MONTH TIME ON LST SUN 03 02 00 OFF LST SUN 10 02 00 CLOCK SET 01 01 00 SAT 00 00 00 LANGUAGE ENGLISH Press the 4 button until ENGLISH is flashing Press the v or A button to select the language of your choice O Press the PAUSE SCAN button to save the settings Clock setting Example To set the clock to October 15 1999 at 3 20 PM 15 20 O Press the AUDIO ON MENU button to display the SET UP 1 menu Press the w or a button to set the auto summer time standard
37. wer to the VCR camera TV monitor and other connected devices Check that the image received on the TV monitor is correct Check that the on screen display of the date and time is correct To check the recording condition of the previous day rewind the recorded tape a few seconds Press the PLAY button and check that the playback image is correct e Check in particular playback of time lapse recording NOTES e If the security lock is engaged it has to be released before proceeding to the inspection Check that the recorded date and time are correct e f any problem is discovered during the inspection turn off the VCR unplug the power cord then consult your dealer English 27 Periodic Inspection Periodic inspection and maintenance should be referred to your dealer If there is noise in the playback picture and it cannot be corrected using the tracking control it may indicated that the video heads need cleaning The video heads should be inspected every 1 000 hours of use to determine if they need to be replaced The video heads usage can be checked using the USED TIME menu Head Care and Cleaning The VCR has a buit in automatic head cleaner Under normal conditions the heads should not require additional cleaning Cabinet Cleaning Clean the outside of the cabinet with a clean soft cloth moistenet with lukewarm water and wrung dry DO NOT USE SOLVENTS OR OTHER TY
Download Pdf Manuals
Related Search