Sanyo ECD-T1550 CD Player User Manual
Contents
1. The adjustment mode will change in the following order VOL_ BAS TRE BAL Volume Bass Treble Balance Fader By pressing VOLUME button 11 or VOLUME button 27 it is possible to adjust the desired sound quality BEEP ADJUSTMENT Press SEL button 10 and hold for more than 2 seconds until BEEP appears on display Press VOLUME button 11 or VOLUME button 27 as follows BEEP 2ND gt BEEP ALL gt BEEP OFF BEEP 2ND mode The beep is only generated when all allowed double function button is pressed long several seconds e g When preset button is pressed When BND LOU button 13 is pressed When AMS button 18 is pressed BEEP ALL mode The beep is generated when every button is pressed BEEP OFF mode The beep is disabled SET THE CLOCK Press the DSP button 15 the clock is shown on the LCD display Then hold down the button until the clock flashes Then press the MANU SKIP button 17 to change hours or MANU SKIP button 16 to change minutes MUTE Press MUT button 2 to mute down the sound instantly If any button except A button 4 is pressed in the mute state the mute mode is released EQUALIZATION Press EQ button 24 to turn on equalization function and to select desired audio mode There are five kinds of mode as below gt FLAT gt CLASSICS gt POP M ROCK M DSP OFF LIQUID CRYSTAL DISPLAY Ex2. Notes on discs e Attempting to use non standard shape discs e g square start heart may damage the unit Be sure to use round shape CD discs only for this unit Do not stick paper or tape etc onto the label side or the recording side of any discs as it may cause a malfunction e Dirt dust scratches and warping discs will cause misoperation B Notes on CD Rs recordable CDs CD RWs rewritable CDs e Be sure to use discs with following marks only for the unit to play Recordable COMPACT DIGITAL AUDIO Rewritable e The unit cannot play a CD R and CD RW that is not finalized Please refer to the manual of your CD R CD RW recorder or CD R CD RW software for more information on finalization process e Depending on the recording status conditions of the disc and the equipment used for the recording some CD Rs CD RWs may not be played on this unit See To have more reliable play back please see following recommendations a Use CD RWs with speed 1x to 4x and write with speed 1x to 2x b Use CD Rs with speed 1x to 8x and write with speed 1x to 2x c Do not play a CD RW which has been written for more than 5 times SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency
3. want to wait press 4 eject button the panel will also turn up When the ignition key is switched to ACC OFF and there is no portable audio player connected to the unit through the AUX IN jack the front panel will change from State 2 to State 1 If there is a portable audio player connected to the unit through the AUX IN jack the front panel will remain State 2 when the key is switched to ACC OFF WIRING CONNECTION 4 x 50W System MAIN UNIT ANTENNA SOCKET o IGNITION RED SWITCH ACC YELLOW MEMORY BACK UP B C D GREY BLACK GROUND B RCA CABLE Rch RED Lch WHITE POWER BLUE ANTENNA FRONT Lch WHITE GREY FRONT Rch SREAKERE JE WHITE BLACK GREY BLACK SPEAKER REAR Lch GREEN CEL REAR Rch SPEAKER JE GREEN BLACK VIOLET BLACK SPEAKER OPERATION Z C oJ OOO LICL L JCOC YJ CeL 9432 11 18 19 20 21 22 6 16617 7 15 OPERATION SWITCHING ON OFF THE UNIT When the hidden panel turns up in State 2 switch the unit on by pressing any button except button 4 When system is on press 9 to turn the unit off SOUND ADJUSTMENT Press SEL button 10 to select the desired adjustment mode
4. Coverage Sensitivity S N 30aB Stereo Separation Frequency Coverage IF Sensitivity S N 20aB DC 12 Volts Negative Ground 178 W x 165 D x 50 H 10dB 10dB 4x 50 Watts 15 Ampere max More than 55 dB More than 45 dB 40 Hz 18 KHz FM 87 5 to 107 9 10 7 MHz 4uV gt 25dB AM 530 to 1710 kHz 450 kHz 36 dBu TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer Symptom Cause Solution No power The car ignition switch is If the power supply is properly not on connected to the car accessory circuits but the engine is not moving switch the ignition key to ACC The fuse is blown Replace the fuse Disc cannot be Presence of CD disc inside Remove the disc in the player loaded or ejected the player then put a new one Inserting the disc in reverse Insert the compact disc with direction the label facing upward Compact disc is extremely Clean the disc or try to play a dirty or defective disc new one Temperature inside the car Cool off or until the ambient is too high temperature return to normal Condensation Leave the player off for an hour or so then try again No sound Volume is in minimum Adjust volume to a desired level Wiring is not properly Check wiring connection c
5. OWNER S OM SANYO ECD T1550 4 OOO ODCLICLICLIOGLIO e PLL Synthesizer Stereo Radio e Digital Compact Disc Player e Automatic Memory Storing e Motorized Hidden Panel e Preset Equalization e Auxiliary Input Jack e Credit Card Remote Control e Multi Color LCD e Plays CD R RW discs CONTENTS Installatioh scocossicosociccociocscircicccscss 3 Take out screw before installation 3 DIN Front Mount Method A 3 Installing the unit 3 Removing the unit 4 DIN Rear Mount Method B 5 Using the front panel 6 Wiring Connection 7 Operation nnisiccccccincescescecercececzetsereine 8 Switching on off the unit 9 Faceplate release 9 Sound adjustment 9 LOUdNESS Eee ao Y E 9 Set the Clock away waza za 9 NITE a OR EE os Pe 9 Equalization sengara 9 Liquid crystal display 9 Flashing LED waze sat ze AA 9 Remote sensor 9 Reset function 2 2 2222221 9 Radio operation 22111111111111 10 Switching to radio mode 10 Selecting the frequency band 10 Selecting station 10 Local distant x sacra 10 Automat
6. R COMMERCIAL PURPOSE THE ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO FISHER COMPANY SFC warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty with new or reconditioned products or parts The warranty period commences on the date the product was first purchased at retail LABOR PARTS 1 YEAR 1 YEAR EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty does not apply to the cabinet or cosmetic parts knobs or routine maintenance This warranty does not apply to the elimination of car static or motor noise correction of antenna problems or damage to compact discs speakers accessories or vehicle electrical systems This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions ship
7. appears on the display e LOCAL DISTANT Press LOC button 3 to select between local and distant stations Local setting for reception of strong station and a distant setting for reception of weaker stations This function is in effect during AUTO SEEK operation e AUTOMATIC MEMORY STORING amp PROGRAM SCANNING Automatic Memory Storing Press AMS button 18 for several seconds the radio searches from the current frequency and checks the signal strength until one cycle search is finished The six strongest stations will be stored into the corresponding preset number button Program Scanning Press AMS button 18 shortly to scan preset station stored in memory e STATION STORING Press any one of the preset buttons 14 M1 to M6 to select a station which had been stored in the memory Press this button for several seconds until 2 nd beeps come out to store current station in that preset button MONO STEREO Press MON button 1 to select mono or stereo mode You can sometimes improve reception of distant stations by selection mono operation CD OPERATION e SWITCHING TO CD MODE If there is no CD inserted in the player When the front panel is in State 2 and the unit is on press EJECT button 4 the panel will change into State 3 and display the disc slot 5 Gently insert the CD with the printed side on top into the CD compartment until you feel some resistance The CD is drawn into the player aut
8. bject to high temperature such as direct sunlight hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods TAKE OUT SCREW BEFORE INSTALLATION Before install the unit please remove the two screws Take out screw before installation DIN FRONT MOUNT Method A Installation Opening This unit can be installed in any dashboard having an opening as show below 53 mm 182 mm Installing the unit Be sure you test all connections first and then follow these steps to install the unit 1 Make sure the ignition is turned off and then disconnect the cable from the vehicle battery s negative terminal 2 Disconnect the wire harness and the antenna 3 The two supplied keys release tabs inside the unit s sleeve so you can remove it Insert the keys as far as they will go with the notches facing up into the appropriate slots at the middle left and right sides of the unit Then slide the sleeve off the back of the unit INSTALLATION metal strap to a solid metal part of the vehicle under the dashboard This strap also helps ensure proper electrical grounding of the unit Slee
9. hibit current frequency and activated functions on the display 8 AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack 7 Note The face plate will not close when something is plugged in the AUX in jack REMOTE SENSOR Point the remote control handset to the remote sensor IR 23 Press the function keys on the handset to control the system RESET FUNCTION RESET button 12 can be activated with either a ballpoint pen or thin metal object The RESET button is to be activated for the following reasons Initial installation of the unit when all wiring is completed Al the function buttons do not operate Error symbol on the display OPERATION RADIO OPERATION e SWITCHING TO RADIO MODE Press MOD button 6 shortly to select radio mode the radio mode appears in the display together with the memory band and frequency e SELECTING THE FREQUENCY BAND At radio mode press BND LOUD button 13 shortly to select the desired band The reception band will change in the following order gt FM1 gt FM2 gt FM3 gt AM e STATION SELECTION Press MANU SKIP button 17 or MANU SKIP lt button 16 shortly to activate automatic seek function Press for several seconds until MANUAL appears on the display the manual tuning mode is selected If both buttons are not pressed for several seconds they will return to seek tuning mode and AUTO
10. ic memory storing amp program scanning 10 Station Storing 11 1111111111 10 Mono stere0 10 CDr0peratioMio n2cec ens 10 Switching to CD mode 10 Selecting trackS 11 Pausing playing 1 111 11 Previewing all tracks 11 Repeating the same track 11 Playing all tracks in random 11 Ejecting a diSC 1 111111 12 11 BISENOES a aiz ai z A ka 11 Specificatii xr itc 2500000 12 Trouble shooting 13 INSTALLATION Notes e Choose the mounting location where the unit will not interfere with the normal activity of the driver e Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly Test to see if the system is working properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions e Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle e Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop e If installation angle exceeds 30 from horizontal the unit might not give its optimum performance a 30 e Avoid installing the unit where it would be su
11. omatically and the panel will automatically turn up CD playback begins OPERATION If a CD is already inserted in the player Keep pressing MOD button 6 shortly until the CD mode display appears e SELECTING TRACKS Press MANU SKIP lt button 16 or MANU SKIP gt button 17 to move to the previous track or the following track Track number shows on display Hold MANU SKIP lt button 16 or MANU SKIP button 17 to fast reverse or fast forward CD play starts when you release the button e PAUSING PLAYING Press PAU button 19 to pause CD player Press it again to resume play e PREVIEWING ALL TRACKS Press SCN button 20 to play first several seconds of each track on the current disc Press it again to stop intro and listen to track e REPEATING THE SAME TRACK Press RPT button 21 to continuously repeat the same track Press it again to stop repeat e PLAYING ALL TRACKS IN RANDOM Press SHF button 22 to play all tracks on CD in random order Press again to cancel the function e EJECTING A DISC When the front panel is in State 2 and there is a disc in the disc slot Press A button 4 the panel will turn down and eject the disc from the disc slot 5 Note When you first play a CD and when whichever track is playing press M5 button or M6 button the unit will search the disc again and start to play the first track Later there is no function of pressing M5 button or M6 button DISC NOTES A
12. onnected Sound skips The installation angle is Adjust the installation angle less more than 30 degrees than 30 degrees The disc is extremely dirty Clean the compact disc then or defective disc try to play a new one The operation keys The built in microcomputer Press the RESET button do not work is not operating properly Front panel is not properly fixed due to noise into its place The radio does not The antenna cable is not Insert the antenna cable firmly work The radio connected station automatic selection does not The signals are too weak Select a station manually work SANYO MOBILE AUDIO MODEL ECD T1550 LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 6382 Weekdays 8 00 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER AND DOES NOT APPLY TO PRODUCTS USED FOR ANY INDUSTRIAL PROFESSIONAL O
13. ping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IS LIMITED TO THE TERM OF THIS WARRANTY IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE For your protection in the event of theft or loss of this product please fill in the information below for your own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased SANYO 21605 Plummer Street Chatsworth CA91311 ECD T1443 Issue Number 1 Printed in Hong Kong 88 C1732 01
14. to the mounting bolt on the back of it possible to remove the unit from the the unit If necessary bend the metal dashboard strap to fit your vehicle s mounting area Then use the supplied hardware Tapping Screw 5x25mm and Plain Washer to attach the other end of INSTALLATION DIN REAR MOUNT Method B RON Ke Factory installed radio bracket Car radio mounting bracket Screw After aligning the car radio mounting bracket with the factory installed radio bracket tighten the screws M5x4mm at 2 places on each side When fixing factory installed radio bracket with the screws use a standard tipped screwdriver to pry the tabs of the car radio mounting bracket to make them fit into the holes in the factory installed radio bracket Movable panel frame USING THE FRONT PANEL 1 When the ignition key is switched to ACC ON the panel of the unit will change from State 1 to State 2 see below the hidden panel will turn up State 2 2 Press power button to turn on the unit Then press eject button the panel will turn down to horizontal position see State 3 f N ep 0 3 Insert a disc in the disc slot the panel will automatically turn up to State 2 Press eject button again the panel will turn down to eject the disc If you don t insert a disc in again the panel will automatically turn up after 10 seconds If you don t
15. ve Spring Washer Hex Nut Metal Strap Mounting Bolt Plain Washer Tapping Screw 4 Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver Not all tabs will be able to make contact so examine which ones will be most effective Bend open the appropriate 8 Reconnect the cable to the vehicle tabs behind the dashboard to secure battery s negative terminal the sleeve in place Dashboard Removing the unit 1 Make sure the ignition is turned off then disconnect the cable from the vehicle battery s negative terminal 2 Remove the metal strap attached the back of the unit if attached 3 Insert the release frame key into the groove at the right side of the frame then prize out to remove the frame You can also use the key to remove the frame from the left side Frame 5 Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables 6 Slide the unit into the sleeve until it locks into place 7 To further secure the unit use the 4 After releasing the frame insert the supplied metal strap to secure the back release unit keys supplied with the of the unit in place Use the supplied accessory into the grooves at both hardware Hex Nut M5mm and Spring sides of the unit as shown in figure Washer to attach one end of the strap until they click Pulling the keys makes
Download Pdf Manuals
Related Search