Samsung SU-8500 Vacuum Cleaner User Manual
Contents
1. 12 TROUBLE SHOOTING eren 13 The design and specification may be different depending on the models Important Safety Instructions Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING reduce the risk of fire electric shock or injury Do not leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not allow children to operate vacuum cleaner or use as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug f vacuum cleaner is not working as it should or has been dropped damaged left outdoors or dropped into water return it to a service center Do not pull or carry by cord use cord as a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surface Do not unplug by pulling on the cord To unplug grasp the plug not the cord Do not handle vacuum cleaner or plug with wet hands Do not put any object into openings Do not use with any opening blocked keep op2. 9 Check Case filter for build up or clogs 4 Remove the Case filter and check the suction inlet for a clog Grasp the Quick Reach Handle and lift Hose Wand to separate from the suction opening Check for a clog in the Base the Wand or the Hose Remove the screw attaching the Hose Wand Base to the vacuum Straighten the Hose Wand Base and unclog with long narrow object Turn the vacuum cleaner off and unplug it Remove the brush cover check the air passageway for obstructions Remove debris from this area Reposition brush cover and eight screws Tighten screws securely snap end of brush cover into place 11 Maintenance Powered hand tool Turbine Brush Brushbar Replacement Remove the tool from the hose and turn upside down Slide the switch to unlock position and remove bottom plate 2 Unscrew the one screw and remove belt guard 3 Remove brushbar including end plates and discard 4 Inspect belt to ensure that it is in good condition If broken or cracked please replace See below for details 5 With the curved ends facing down slide end plates of brushbar into slots the tool To replace bottom plate insert the four tabs on edge of bottom plate into slots on front of tool Pivot bottom plate down and snap closed Belt replacement 1 Grasp turbine and pull firmly to remove 2 Remove a screw and lift the cover belt off 9 Remove belt from turbine pulley Replace with new belt With flat
3. keep away from babies and children Vacuum Cleaner Assembly Carton contents A Empty carton Find the parts shown above before disposing of packing materials A Handle section with 4 screws B Cleaner body Attach Handle To Vacuum Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body Check to be sure the handle is fitted to the cleaner body If there is a gap in front continue to push firmly until the handle is flush Insert the two screws provided into the existing holes Tighten the screws securely with a screwdriver Before securing the handle please check that the handle is fitted to the vacuum body and there s no gap between them If there is a gap or the screw is loosened cleaner won t turn Attach Handle To Dirt Cup The dirt cup assembly consists of the following parts Dirt Cup A Dirt Cup Handle B 1 Unlock the dirt cup from the cleaner body Insert the dirt cup handle into the dirt cup as shown Press firmly until it locks in place 3 Insert the dirt cup into the cleaner body and lock Accessories The accessories are packed on the cleaner Not all accessories are included with every model C Hose D Extension wand Crevice tool Powered hand tool G Dusting Brush Turbine Brush H Upholstery Brush Furniture nozzle Vacuum Cleaner Assembly Attach Vacuum Hose and
4. Check for clogs This Vacuum cleaner is approved the following EMC Directive 89 336 92 31 EEC and 93 68 EEC Low Voltage Safety Directive 73 23 EEC and 93 68 EEC 13 DJ68 00237A REV 0 0
5. Tools for storage The top hook rotates right or left for easy cord release N e v 9 SU 0 Slide the extend wand into the storage clip Insert the crevice tool into the nook nx WY Attach the hose with two screws Snap the hose into the hose clip as from the assembly packet Tighten shown securely them with a screw driver NOTE The powerfoot will not operate effectively unless the Hose is firmly attached to the base CCC K __ Kua E i X Snap in the Dusting brush and insert upholstery brush into the storage clip as shown Operation Power Switch Brush Roll Switch Circuit Breaker The power control slide switch is located on the front of the handle This switch also allows you to control the cleaning power 1 Plug cord into electrical outlet To turn cleaner ON I slide the power switch up To turn cleaner OFF O slide the power switch down The headlight turns on when in use The brush roll switch is located on the side of the cleaner body This switch turns the rotating brush on and off The brush switch should be in the position for normal carpet cleaning You may want to turn the brsuh switch OFF O for bare floor cleaning or other delicate surfaces
6. Turn brush roll switch OFF O to clean hard surface floors Turn brush roll switch to clean carpet and rugs The brush rolls will automatically turn off when the handle is in the upright position Ld 2 a NOTE Your SAMSUNG vacuum is equipped with a special internal switch that turns the Rotating Brush off whenever the unit is in the Upright position CIRCUIT BREAKER CIRCUIT BREAKER Circuit Breaker Reset Switch The Circuit breaker turns off the brush rolls if there is an obstruction in them The circuit breaker combining ON OFF switching and extremely fast overload performance in a rocker switch Under overload conditions an internal neon filament bulb for low voltages illuminates to give a cleaner signal of the tripped status of the mechanism and thereby the cause of power interruption Returning the rocker switch through the OFF position and back ON will reset the mechanism and restore the supply The brush rolls will not turn but the suction motor will continue to run To reset the breaker turn cleaner off and unplug it Clear obstruction Press circuit breaker switch to the position Turn cleaner ON and continue cleaning Handle Positions Select the desired angle of the cleaner using the handle release pedal The handle of your cleaner has three positions 1 Step on the handle release pedal on the back of the cleaner base 2 Raise or lower the handle and release the pedal A Upright For stora
7. Vacuum Cleaner SU 8500 Series FOR HOUSEHOLD USE ONLY Operating Instructions IMPORTANT SAFETY INSTRUCTIONS VACUUM CLEANER DISCRIPTION VACUUM CLEANER 4 CARTON CONTENTS 4 ACCESSORIES 1 000000 4 ATTACH HANDLE 4 ATTACH HANDLE TO DIRT CUP 4 ATTACH VACUUM HOSE AND TOOLS 5 OPERATION ee 6 POWER SWITCH BRUSH ROLL SWITCH CIRCUIT 6 HANDLE 6 POWERFOOT HEIGHT ADJUSTMENT EDGE CLEANING rre CLEANING TOOLS nnns 7 POWER CORD ARRANGEMENT 8 CORD 2 6002 8 TRANSPORTING 1 8 CARRYING CLEANER 8 MAINTENANCE nnne 9 DIRT CUP CHECK OR FILTER CLOGGED INDICATOR 9 CLEANING DIRT CUP ern 9 CLEANING THE CARTRIDGE FILTER TANK 9 CLEANING THE HEPA MEDIA POST MOTOR FILTER 9 CHECK ROTATING FLOOR BRUSH AND DRIVE BELT 10 DRIVE 10 CLEARING CLOGS ern 11 POWERED HAND TOOL TURBINE BRUSH 12 BRUSHBAR 12 BELT
8. ance Dirt Cup check or Filter clogged Indicator The Dirt Cup check Indicator on the front of the vacuum shows a red or green display When the Dirt Cup display is green the Dirt Cup is not yet full or the filter is not clogged When the indicator turns to red the Dirt Cup needs to be emptied or the filter needs to be cleaned If the display is still red after emptying the dust container turn the cleaner off to see if the hose tube or nozzle is clogged Cleaning the Dirt cup 1 Unplug the Cleaner from electrical outlet The Dirt cup can be reached by removing the Dirt cup reaching underneath the Upper Tank and turning the rim of the Filter Frame to unlock Pull straight down to remove Brush the dirt off the Louvers and Dirt cup The foam Upper Tank Filter may be removed and hand washed in cold water with mild detergent Rinse well then air dry throughly before replacing Cleaning the Cartridge Filter Tank 1 Unplug the Cleaner from electrical outlet The Cartridge Filter Tank assembly can be reached by Do not operate cleaner pulling it from the cleaner with damp or wet filters Remove the cover from the Cartridge Filter Tank and or without all filters in the foam may be removed and hand washed in cold place water with mild detergent then air dried 4 Reposition Filters when completely dry Cartridge Filter Tank Cleaning the HEPA Media Post Motor Filter 1 Unplug the Cleane
9. enings free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dirt cup or filters in place Empty dirt cup and clean filter frequently when picking up very fine materials such as powder Turn off all controls before unplugging vacuum cleaner Use extra care when cleaning on stairs Do not use to pick up flammable or combustible materials such as gasoline or fine wood fine wood sandings or use in areas where they may be present e Store your vacuum cleaner indoors in a cool and dry area Avoid picking up hard sharp objects with the cleaner They may damage the cleaner e Always turn off this appliance before connecting or disconnecting the hose removing the bottom plate for maintenance Use only on dry indoor surfaces never change the plug in any way Do not modify the polarized plug to fit a non polarized outlet or extension cord Do not touch the brush roller when it is rotating Keep suction away from your face when using nozzles and pipe Do not pull the power cord around sharp corners and do not allow it to be trapped Unplug before connecting turbine nozzle only using turbine brush model his appliance is not intended for use by young persons or infirm persons without supervision unl
10. ess they have been adequately supervised by a responsible person to ensure that they can use the appliance safely Young children should be supervised to ensure that they do not play with the appliance The plug must be removed from the socket outlet before cleaning or maintaining the appliance f the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only Vacuum Cleaner Description Assembled Vacuum Cleaner Parts BRUSH ROLL ON OFF SWITCH TOOL COVER tm POWERED Il HAND TOOL ll CARTRIDGE CHECK FILTER FILTER TANK Il INDICATOR LOUVERS FILTER FRAME HEPA MEDIA DIRT CUP DIRT CUP 2 HANDLE RELEASE LEVER HEIGHT ADJUSTMENT KNOB FURNITURE GUARD N CAUTION Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures ON OFF POWER CONTROL SWITCH POST MOTOR FILTER DIRT CUP HANDLE COMFORT GRIP CORD CLIP DUSTING BRUSH QUICK RELEASE UPHOLSTERY HOSE CLIP ANS CARRYING N POWER CORD HANDLE D SUCTION INLET FOR HOSE i CACT EH gt m zZ 92 O See cum mies CREVICE TOOL N WARNING Plastic film can be dangerous To avoid danger of suffocation
11. ey and Drive Belt areas 1 1 Check Drive Belt carefully for wear cuts stressed areas 1 p nex Air Passageway for obstructions Remove debris from this area Replace Drive Belt OI A PO Unplug cleaner from electrical outlet With Rotating Floor Brush removed from vacuum cleaner Step1 7 of Check Rotating Floor and Drive Belt grasp old Drive Belt and remove from Motor pully Discard old Drive Belt Place new Drive Belt over motor pulley and stretch other end over rotating Floor Brush in the space between the bristles Place ends of rotating Floor Brush down into slots on sides as shown Turn rotating Floor Brush by hand several times in direction of motor pulley if properly installed Drive Belt will center itself Reposition Brush cover and eight screws Tighten screws securely Snap end of Brush cover into place 10 Maintenance Maintenance Clearing Clogs Low suction or poor pickup may be due to a clog in the vacuum cleaner If you notice a change in the sound of the motor or a reduction in the spinning action check for clogs 1 Unplug cleaner from electrical outlet 2 Empty Dirt Cup
12. ge and elevated cleaning with cleaning tools B Medium position For general operation on carpet and floors C Low position Use for reaching under low furniture Step on handle release lever to lower handle Operation Powerfoot Height Adjustment The powerfoot on your SAMSUNG vacuum can be adjusted to clean several floor surfaces NOTE For optimal cleaning performance adjust to the lowest practical setting If your cleaner is difficult to push adjust to the next higher setting 1 Place Handle in Upright Position 2 Turn Height Adjustment Knob to desired setting Lowest Setting For bare floors Medium Settings For short and medium pile carpets Highest Setting For plush pile carpet NOTE You may also adjust the setting while in the Medium position Edge Cleaning The Edge Cleaning Feature helps the cleaner to clean edges of rugs and floors effectively allowing suction to reach against walls and near furniture Cleaning Tools Attachment tools can be used to clean furniture drapes stairs or in corners Place the vacuum on the floor with the handle in the upright position while using attachment tools Do not place the vacuum on top of furniture or steps as the brushroller may cause damage 1 Unhook hose with cleaning tools attached from the rear of the vacuum cleaner Place desired tool on end of narrow wand Press firmly and twist to connect the tool to the
13. r from electrical outlet The HEPA Media Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the side of the cleaner If the filter becomes dirty open the door remove the filter and clean To remove this filter open the door on the side of the cleaner grasp filter and pull it straight out 9 Reposition the HEPA Media Post Motor Filter then lock the door To reduce the risk of injury from moving parts turn off vacuum cleaner and disconnect Power Plug from electrical outlet Check Rotating Floor Brush and Drive Belt You should check your vacuum cleaners Rotating Floor Brush and Drive Belt regularly for wear or damage You should also clean the brush and brush ends of strings hair and carpet fibers These can wrap around the brush and hamper its ability to effectively clean your carpet Also remove any debris that has accumulated under the brush cover CO NI O OI A G PO Unplug cleaner from electrical outlet Place handle in Low position Remove the four screws as shown with a screwdriver Turn over the cleaner Remove the eight screws and turn over the cleaner again Lift the cover Brush off Remove the three screws on the case drum Grasp Rotating Floor Brush at both ends and lift Clean strings hair and other debris from Rotating Floor Brush paying particular attention to brush ends 1 er strings hair and other debris from Motor Pull
14. sides of turbine retainers pointing down slide retainers into grooves in tool housing and snap into place 5 Replace brushbar and bottom plate Cleaning Brushbar e Cut off pet hairs or threads surrounding brush by using scissors 12 Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center Problem Possible solution CLEANER WON T TURN ON Not firmly plugged in No voltage in wall plug Blown fuse or tripped breaker On Off switch not turned on CLEANER WON T PICK UP Circuit breaker tripped e Agitator brush rolls worn e Dirt cup full e Incorrect carpet height setting HEPA cartridge filter clogged e Pre filter clogged e Dirt cup not properly installed Filter assembly not assembled properly Blockage in hose or air flow passage Broken belt Hose not inserted fully e Plug unit in firmly Check fuse or breaker Replace fuse or reset breaker e Slide to on e Tighten the screw of the handle Reset circuit breaker e Replace brush rolls e Empty dirt cup e Move nozzle control knob to lower settings Clear HEPA cartridge filter by either tapping the side of the dirt cup Clean pre filter Position dirt cup properly Ensure that filter assembly is positioned properly e Clear blockage Replace belt e Insert hose ABNORMAL SOUND e Strange sound like air rushes
15. wand A Dusting Brush Use for carved furniture table tops books lamps lighting fixtures venetian blinds base boards shutters and registers B Crevice tool Use in corners on stairs baseboards and behind furniture Operation C Extension Wand Use with desired attachments and narrow wand for a longer reach D Powered hand tool Turbine Brush Use for upholstered furniture carpeted stairs and hard to reach places E Upholstery Brush Use for upholstered furniture draperies mattresses clothing automobile interiors and carpeted stairs Power Cord Arrangement When you are done using your SAMSUNG vacuum return it to the Upright position and store the Power Cord 1 Turn vacuum cleaner OFF O 2 Unplug Power Cord by grasping the polarized plug Not the cord and disconnect from outlet 9 Loop Power Cord around Cord Wraps on side of vacuum cleaner 4 Clip molded plug to Power Cord to secure Cord Clip For easier handling while Vacuuming hook the power cord onto the power cord clip Transporting Cleaner To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward Carrying Cleaner Do not lift cleaner using dirt cup handle A The cleaner can be moved by using the carrying handle located on the back of the cleaner 0 a 5 LLL r CCC Mainten
Download Pdf Manuals
Related Search