Samsung DV337AGG Clothes Dryer User Manual
Contents
1. CONFORM WITH LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES WITH THE NATIONAL FUEL GAS CODE ANSI Z223 1 LATEST REVISION FOR THE UNITED STATES OR WITH THE CAN CGA B149 INSTALLATION CODES FOR CANADA Gas dryers are equipped with a burner vent for use with natural gas If you plan to use your dryer with LP liquid propane gas it must be converted for safe and proper performance by a qualified service technician A 1 2 1 27 cm gas supply line is recommended and must be reduced to connect to the 3 8 1 cm gas line on your dryer The National Fuel Gas Code requires that an accessible approved manual gas shut off valve be installed within 6 of your dryer Gas dryers installed in residential garages must be raised 18 inches 46 cm above the floor Additionally a 1 8 0 3 cm N P T National Pipe Thread plugged tapping accessible for test gauge connection must be installed immediately upstream of your dryer s gas supply connection Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system DO NOT reuse old flexible metal gas lines Flexible gas lines must be design certified by the American Gas Association CGA in Canada 4 e Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas e Asacourtesy most local gas utilities will inspect a gas appliance installation GAS IGNITION Your dryer uses an automatic ignition system to ignite the burn2. and dry with a clean cloth DRYER EXTERIOR Clean with a soft damp cloth Do not use abrasive substances Protect the surface from sharp objects DRYER EXHAUST SYSTEM Should be inspected and cleaned yearly to maintain optimum performance The outside exhaust hood should be cleaned more frequently to ensure proper operation Care and cleaning _23 Buluesjo pue aed g0 special laundry tips Please follow the care label or manufacturer s instructions for drying special items If care label instructions are not available use the following information as a guide Bedspreads amp Comforters Follow the care label instructions or dry on the Normal cycle and High temperature Make sure the item is thoroughly dry before using or storing May require repositioning to ensure even drying Blankets Use Normal and dry only one blanket at a time for best tumbling action Make sure the item is thoroughly dry before using or storing Curtains amp Draperies Use the Perm Press cycle and Low or Extra Low temperature to help minimize wrinkling Dry these in small loads for best results and remove as soon as possible Cloth Diapers Use the Normal cycle and the High temperature setting for soft fluffy diapers Down filled Items jackets sleeping bags comforters etc Use the Normal cycle and the Low or Extra Low temperature setting Place a clean pair of sneakers in your dry
3. be completely dry when the rest of the load has reached the selected dryness level Sort heavy items from lightweight items for best drying results has an odor Household odors from painting varnishing strong cleaners etc may enter the dryer with the surrounding room air This is normal as the dryer draws the air from the room heats it pulls it through the tumbler and exhausts it outside When these odors linger in the air ventilate the room completely before using the dryer shuts off before load is dry Dryer load is too small Add more items or a few towels and restart the cycle Dryer load is too large Remove some items and restart the dryer INFORMATION CODES Information codes may be displayed to help you better understand what is occurring with your Dryer CODE SYMBOL MEANING SOLUTION Le Heater temperature control Call for service See below Co problem JIC Door open sensing problem Call for service See below DT I Door open error When the door is Be sure the door is latched shut If problem Ol open the dryer will not operate continues call for service See below For any codes not listed above call 1 800 726 7864 1 800 SAMSUNG 26_ Troubleshooting anpenalx FABRIC CARE CHART The following symbols provide garment care direction The Clothing care labels include symbols for washing bleaching drying and ironing or dry cleaning when necessary The use of s
4. heat e Check the home s circuit breaker and fuses a ao doesn t dry e Check all of the above plus e Be sure the exhaust hood outside the home can open and close freely e Check exhaust system for lint buildup Ducting should be inspected and cleaned annually e Use a 4 rigid metal exhaust duct e Do not overload 1 wash load 1 dryer load e Sort heavy items from lightweight items e Large bulky items like blankets or comforters may require repositioning to ensure even drying e Check that the washer is draining properly to extract adequate water from the load e Load may be too small to tumble properly Add a few towels is noisy e Check the load for objects such as coins loose buttons nails etc Remove promptly e It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle e Be sure the dryer is leveled properly as outlined in the installation instruction e tis normal for the dryer to hum from the high velocity of air moving through the dryer drum and exhaust system Troubleshooting _25 troubleshooting dries unevenly Seams pockets and other similarly heavy areas may not be completely dry when the rest of the load has reached the selected dryness level This is normal Select the Very Dry setting if desired If one heavy item is dried with a lightweight load such as one towel with sheets it is possible that the heavy item will not
5. in severe personal injury or death WARNING N Hazards or unsafe practices that may result in minor personal injury or property damage CAUTION A Follow the information in this manual to minimize the risk of fire or explosion or to prevent property damage personal injury or death CAUTION T Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance Do NOT attempt Do NOT disassemble Do NOT touch Follow directions explicity Unplug the pwer plug from the wall socket Make sure the machine is grounded to prevent electric shock Call the service center for help DEEA WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not turn on the appliance e Do not touch any electrical switch e Do not use any phone in your building e Clear the room building or area of all occupants e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier Safety information _3 Safety Instructions Read all instructions before using the appliance A To reduce the risk of fire or explosion WARNING e Do not dry items that have been previously cleaned washed soaked or spotted with gasoline dry clean
6. long duct runs with many elbows 4 Allowing crushed or clogged ducts and vent 16_ Installing your dryer DOOR REVERSAL Reassemble the black screw in the other hole i Unplug the power cord 2 Remove two door hinge screws 3 Lift the door and remove from the dryer Place the door on the other side and reattach it to the dryer 4 Remove two screws on the opposite side of the door hinge aaA p noA Guijyeysuy LO Reassemble the holder lever 5 Remove two screws from the holder lever 10 Reassemble the screws in the remaing holes 6 Remove one black screw from the door hinge Installing your dryer 17 operating Instructions tios OVERVIEW OF THE CONTROL PANEL fv Be Very Dry High More Dry Medium Normal Dry Med Low Low Extra Low Dry Level Temp Drying Cooling Wrinkle Prevent Wrinkle Prevent Time 06 Sensor Dry 4 gt Manual Dry Normal Freshen up AN 60min AdjustTime N Heavy Duty Time Dry 50min 1 Wrinkle 1 28 40min Towels Release rod 30min 20min Perm Press Air Fluff Delicates o oog Digital Graphic The display window shows the estimated time remaining in the cycle after the Start Pause button is pressed The estimated time remaining may fluctuate as the cycle progresses The Drying light will illuminate and
7. remain lit until the cycle is complete When your dryer is in the cool down phase the Cooling light will illuminate When your dryer is in the wrinkle prevent phase the Wrinkle Prevent light will Display illuminate When the cycle is complete END will appear in the display panel until the dryer door is opened or Power key is pushed If your dryer is paused during a cycle the indicator lights will blink until the Start Pause button is pressed To select the dry level in the Normal Heavy Duty or other Sensor Dry cycles press the Dry Level button An indicator light will illuminate next to the desired dryness level Dry level Press the button repeatedly to scroll through the settings Larger or bulkier 2 Selection Button loads may require the Very Dry or More Dry setting for complete dryness The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle Damp Dry is designed to partially dry items Use for items that lay flat or hang to dry Temp Selection s Button To select the correct temperature for the load press the Temp button An indicator light will illuminate next to the desired temperature Press the button repeatedly to scroll through the settings High For sturdy cottons or those labeled Tumble Dry Medium For permanent press synthetics lightweight cottons or items labeled Tumble Dry Medium Medium Low For lower heat than Me
8. tops on the floor Tip your dryer on its side so it will lay across both cushion tops Set your dryer back in an upright position Review the Exhausting section before installing the exhaust system Install the ductwork from your dryer to the exhaust hood The crimped end of the duct sections must point away from your dryer DO NOT use sheet metal screws when assembling ducting These joints should be taped Never use plastic flexible exhaust material Tip for tight installations install a section of exhaust system to your dryer before putting it in place Use duct tape to secure this section to your dryer but do not cover ventilation slots at the back of the unit in dryer cabinet Review Electrical Requirements section BEFORE OPERATING OR TESTING follow the grounding instructions in the Grounding section U S MODELS IMPORTANT All U S models are produced for a 3 WIRE SYSTEM CONNECTION The dryer frame is grounded to the neutral conductor at the terminal block A 4 WIRE SYSTEM CONNECTION is required for new or remodeled construction mobile homes or if local codes do not permit grounding through neutral If the 4 wire system is used the dryer frame cannot be grounded to the neutral conductor at the terminal block Refer to the following instructions for 3 and 4 WIRE SYSTEM CONNECTIONS Remove the terminal block cover plate Insert the power cord with a UL listed strain relief through the hole provided in the cabinet near the te
9. DUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state To obtain warranty service please contact SAMSUNG at SAMSUNG ELECTRONICS AMERICA INC CONSUMER ELECTRONICS CUSTOMER SERVICE 400 Valley Road Suite 201 Mt Arlington NJ 07856 1 800 SAMSUNG 1 800 726 7864 www samsung com Warranty _31 QUESTIONS OR COMMENTS Country CALL OR VISIT US ONLINE AT WRITE IN THE USA 1 800 SAMSUNG 726 7864 www samsung com Samsung Electronics America Inc Code No DC68 02453A 02_EN
10. Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil Even after being washed these items may contain significant amounts of these oils The residual oil can ignite spontaneously The potential for spontaneous combustion increases when the items containing vegetable oil or cooking oil are exposed to heat Heat sources such as your dryer can warm these items allowing an oxidation reaction in the oil to occur Oxidation creates heat If this heat cannot escape the items can become hot enough to catch fire Piling stacking or storing these kinds of items may prevent heat from escaping and can create a fire hazard All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous Washing these items in hot water with extra detergent will reduce but not eliminate the hazard Always use the Cool Down cycle for these items to reduce their temperature Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle Never pile or stack these items when they are hot Safety information _5 contents INSTALLING YOUR DRYER OPERATING INSTRUCTIONS TIPS 6_ Contents CARE AND CLEANING SPECIAL LAUNDRY TIPS TROUBLESHOOTING APPENDIX 25 26 27 28 28 28 29 Tools needed for installation See Exhaust Requirements Ducting requirements Important to installer location considerations Alcove or c
11. Gas and Electric Dryer user manual imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service please register your product at www samsung com global register ar features oh 8 Extra Large Capacity Ultra drying capabilitlites are at your fingertips Now you can dry extra large loads Our ultra large 7 3 cu ft capacity dryer circulates more air through your clothes getting them dry faster for a wrinkle free result Various Drying Cycles amp Fuzzy Logic Algorithm Simply turn the Jog Dial to select one of the 11 automatic drying cycles including normal heavy duty and towels or let the Fuzzy Logic Control measure the degree of dampness and automatically set the drying time Precision drying has never been easier than with Samsung Freshen Up Cycle Want to freshen up a garment that doesn t need washing but could use a little help after last night s party Our Freshen Up Cycle removes odors adding that extra freshness to give more mileage to your clothes Time Saving Our cycles are designed with you in mind All our dryers are designed to dry your clothes in less time just 44 minutes Giving you time for more important things in life Energy Saving Samsung dryers are super energy efficient using only 3 01 kWh per pound of laundry Also both the large capacity and Fuzzy Logic Control save energy by automatically drying your clothes the most
12. Nut drivers oe ee To Level Phillips Screwdriver Duct tape Crescent spanner Installing your dryer _7 Installing your dryer DUCTING REQUIREMENTS Use a 4 inch 10 2 cm diameter rigid aluminum or rigid galvanized steel duct Do not use a smaller duct Ducts larger than 4 inches 10 2 cm in diameter can result in increased lint accumulation Lint accumulation should be cleaned regularly If a flexible metal duct must be used use the type with a stiff sheet metal wall Do not use a flexible duct with a thin foil wall Serious blockage can result if the flexible metal duct is bent too sharply Never install any type of flexible duct in walls ceilings or other concealed spaces Keep the exhaust duct as straight and short as possible Secure joints with duct tape Do not use screws DO NOT EXHAUST DRYER INTO ANY WALL CEILING CRAWL SPACE OR CONCEALED SPACE OF A BUILDING GAS VENT OR ANY OTHER COMMON DUCT OR CHIMNEY THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER Plastic flexible duct can kink sag be punctured reduce airflow extend drying times and affect dryer operation Exhaust systems longer than recommended can extend drying times affect machine operation and may collect lint The exhaust duct should end with an exhaust hood with a swing out damper to prevent back drafts and entry of wildlife Never use an exhaust hood with a magnetic damper The hoo
13. cleaning Appendix _27 aooendix PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials If you decide to dispose of this appliance please observe local waste disposal regulations Cut off the power cord so that the appliance cannot be connected to a power source Remove the door so that animals and small children cannot get trapped inside the appliance DECLARATION OF CONFORMITY This appliance complies with UL2158 SPECIFICATION TYPE FRONT LOADING WASHER DIMENSION Div Inches cm Div Inches cm A Height 38 96 5 C Depth with 49 124 5 door open 90 B Width 27 68 6 D Depth 30 25 77 0 WEIGHT 56 8 kg HEATER RATING 5300 W POWER NO HEAT 268 W CONS UMETION HEATING 5445 W 28_ Appendix CYCLE CHART 7 Wrinkle aa Default Drying Cooling prevent ycle au Sensor dry Time Time Time Time control level High j Normal Medium Normal dry 44 min 39 min 5 min 90 min z 7 High No 3 Heavy Duty change Normal dry 60 min 55 min 5 min 90 min 8 High 2 Sensor Dry Towels Medium Normal dry 52 min 47 min 5 min 90 min a Perm Press ML Normal dry 34 min 24 min 10 min 90 min No change Delicates a Normal dry 29 min 24 min 5 min 90 min Freshen Up nn 30 min 25 min 5 min Time Dry High 40 min 35 min 5 min Manual Dry Kalle Medium 25 mi
14. d should have at least 12 inches 30 5 cm of clearance between the bottom of the hood and the ground or other obstruction The hood opening should point down Never install a screen over the exhaust outlet To avoid lint buildup do not exhaust the dryer directly into a window well Do not exhaust under a house or porch If exhaust ductwork must run through an unheated area the duct should be insulated and slope slightly down towards the exhaust hood to reduce condensation and lint buildup Inspect and clean the interior of the exhaust system at least once a year Unplug the power cord before cleaning Check frequently to be sure the exhaust hood damper opens and closes freely Check once per month and clean at least one time per year Note If clothes are not getting dry then check ducting for obstructions ELECTRIC AND GAS DRYER Weather Hood Type Recommended Use only for short run installation y 4 10 16 cm 2 5 6 35 cm No of 90 elbows Rigid Metallic Flexible Rigid Metallic Flexible O 24 4 m 80 ft 12 4 m 41 ft 22 6 m 74 ft 10 1 m 33 ft 1 20 7 m 68 ft 11 2 m 37 ft 18 9 m 62 ft 8 8 m 29 ft 2 17 4 m 57 ft 10 1 m 33 ft 15 5 m 61 ft 7 6 m 25 ft 3 14 3m 47 ft 9 0 m 29 ft 12 5 m 41 ft 6 5 m 21 ft Do not use non metallic flexible duct 8_ Installing your dryer If the new dryer is installed into an existing exhaust system you mus
15. dium to dry synthetic or washable knit fabrics Low For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm Extra Low Provides the lowest heated dry temperature possible Time Selection 4 Button When using Manual Dry cycles time can be adjusted by pressing the time selection button During the Sensory Dry cycle the time light indicator is off because exact drying times are determined by fluctuating humidity levels 18_ Operating Instructions Tips 5 Signal Selection Button When the cycle is complete a chime will sound When the Wrinkle Prevent option is selected the chime will sound intermittently Adjust the volume of the chime or turn it off by pressing the Signal button Press the button repeatedly to scroll through the choices Wrinkle Prevent Selection Button Wrinkle Prevent provides approximately 90 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling Press the Wrinkle Prevent button to activate this feature The indicator light above the pad will illuminate when Wrinkle Prevent is selected The load is dry and can be removed at any time during the Wrinkle Prevent cycle Select Cycle Option Adjust Time Time can be added or subtracted from the automatically set times in the Manual Dry cycles Time Dry Freshen Up Delicates Wrinkle Release or Air Fluff cycles To add or subtract time from the cycle press the Adjust Time arr
16. duct at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer This limited warranty covers manufacturing defects in materials and workmanship encountered in normal noncommercial use of this product and shall not apply to the following damage that occurs in shipment delivery and installation applications and uses for which this product was not intended altered product or serial numbers cosmetic damage or exterior finish accidents abuse neglect fire water lightning or other acts of nature or God use of products equipment systems utilities services parts supplies accessories applications installations repairs external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems incorrect electrical line voltage fluctuations and surges customer adjustments and failure to follow operating instructions maintenance and environmental instructions that are covered and prescribed in the instruction book product removal and reinstallation problems caused by pest infestations This limited warranty does not cover problems resulting from incorrect electric current
17. ectrical Code CSA C22 1 Latest Revisions and local codes and ordinances It is your responsibility to provide adequate electrical services for your dryer All gas installations must be done in accordance with the national Fuel Code ANSI Z2231 Latest Revision for the U S or CAN CGA B149 Installation Codes Latest Revision for Canada and local codes and ordinances GROUNDING This dryer must be grounded In the event of malfunction or breakdown the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current Gas models Your dryer has a cord with an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided with your dryer if it doesn t fit the outlet have a proper outlet installed by a qualified electrician NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES GAS LINES OR HOT WATER PIPES Electric models Your dryer has a cord with an equipment grounding conductor and a grounding plug sold separately The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances If a power cord is not used and the electric dryer is to be permanently wired the dryer must be connected to a permanently grounded metal wiring syst
18. efficient way Easy Reversible Door Our dryers will fit just about anywhere and without a door conflict The direction of our easy reversible door can be changed with just four screws Pedestal with Storage Drawers An optional 15 pedestal is available to raise the washer for easier loading and unloading It also offers a built in storage drawer that can hold a 100 oz bottle of detergent Stacking MODEL NO SK 3A1 XAA Samsung s Washer and Dryer can be stacked to maximize usable space 9 The Dryer legs need to be removed to stack the Washer and Dryer An optional stacking kit is available for purchase from your Samsung retailer 2_ Features of your new silvercare washer Safety Instructions Congratulations on your new Samsung Dryer This manual contains valuable information on the installation use and care of your appliance Please take the time to read this manual to take full advantage of your dryer s many benefits and features WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur It is your responsibility to use common sense caution and care when installing maintaining or operating your dryer Always contact your manufacturer about problems or conditions you do not understand IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS AN Hazards or unsafe practices that may result
19. elief e Do not reuse a power supply cord from an old dryer The power cord electric supply wiring must be retained at the dryer cabinet with a suitable UL listed strain relief e Grounding through the neutral conductor is prohibited for 1 new branch circuit installations 2 mobile homes 8 recreational vehicles and 4 areas where local codes prohibit grounding through the neutral conductor Use 4 prong plug for 4 wire receptacle NEMA type 14 30R aaA p noA GBuirjyeysuy LO Electric models Canada Only e A 120 240 volt 60 Hz AC approved electrical service fused through a 30 ampere fuse or circuit breaker on both sides of the line is required e All Canadian models are shipped with the power cord attached The power cord should be plugged into a 30 ampere receptacle It is not permissible to convert a dryer in Canada to 208 volts REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1 800 SAMSUNG 726 7864 Installing your dryer _13 Installing your dryer INSTALLATION For proper installation it is highly recommended to hire a professional To install 1 D Move your dryer to an appropriate location for installation Consider installing the dryer and washer side by side to allow access to gas electrical and exhaust connections Lay two of the carton cushion
20. em or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal 12_ Installing your dryer ELECTRICAL CONNECTIONS Before operating or testing follow all grounding instructions in the Grounding section An individual branch or separate circuit serving only your dryer is recommended DO NOT USE AN EXTENSION CORD Gas models U S and Canada A 120 volt 60 Hz AC approved electrical service with a 15 ampere fuse or circuit breaker is required Electric models U S only Most U S dryers require a 120 240 volt 60 Hz AC approved electrical service Some require 120 208 volt 60 Hz approved electrical service The electric service requirements can be found on the data label located behind the door A 30 ampere fuse or circuit breaker on both sides of the line is required e If a power cord is used the cord should be plugged into a 30 ampere receptacle e The power cord is NOT provided with U S electric model dryers IMPORTANT When local codes allow the dryer electrical supply may be connected by means of a new power supply cord kit marked for use with a dryer that is U L listed and rated at a minimum of120 240 volts 30 ampere with three No 10 copper wire conductors terminated with closed loop terminals open end spade lugs with turned up ends or with tinned leads 1 size of the conductors and the type of cord 2 8 4 1 9 cm UL listed strain r
21. er There is no constant burning pilot Commonwealth of Massachusetts installation instructions Your dryer must be installed by a licensed plumber or gas fitter A T handle manual gas valve must be installed in the gas supply line to your dryer If a flexible gas connector is used to install your dryer the connector must have a maximum length of 3 36 Gas leaks may occur in your system creating a dangerous situation warno Gas leaks may not be detected by smell alone Gas suppliers recommend you purchase and install a UL approved gas detector Install and use in accordance with manufacturer s instructions Installing your dryer _11 aaA p noA Guijyeysuy LO Installing your dryer ELECTRICAL REQUIREMENTS Z Wiring diagram is located on plate below the control panel WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded Do not modify the plug provided with your dryer if it doesn t fit the outlet have a proper outlet installed by a qualified electrician To prevent unnecessary risk of fire electrical shock or personal injury all wiring and grounding must be done in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA No 70 Latest Revision for the U S or the Canadian El
22. er with the item to fluff the down comforters etc Adding a couple of dry towels shortens drying time and absorbs moisture Foam Rubber rug backs stuffed toys shoulder pads etc DO NOT dry on a heat setting Use the Air Fluff cycle no heat WARNING Drying a rubber item with heat may damage it or be a fire hazard Pillows Use the Normal cycle Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the item DO NOT dry kapok or foam pillows in dryer Plastics shower curtains outdoor furniture covers etc Use the Air Fluff cycle or the Time Dry cycle and the Low or Extra Low temperature setting depending on the care label instructions THINGS TO AVOID e Fiberglass items curtains draperies etc e Woolens unless recommended on the label e Vegetable or cooking oil soaked items 24_ Special laundry tips troubleshooting CHECK THESE POINTS IF YOUR DRYER e Select a heat setting other than Air Fluff e On a gas dryer check that the gas supply is on e Clean the lint filter and exhaust duct e Dryer may have moved into the cool down phase of the cycle PROBLEM SOLUTION doesn t run e Be sure the door is latched shut e Be sure the power cord is plugged into a live electrical outlet e Check the home s circuit breaker and fuses a e Press the Start Pause button again if the door is opened during the cycle D doesn t
23. ing solvents or other flammable or explosive substances They emit vapors that could ignite or explode Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed There are many highly flammable items used in homes such as acetone denatured alcohol gasoline kerosene some liquid household cleaners some spot removers turpentine waxes and wax removers e Items containing foam rubber may be labeled latex foam or similarly textured rubber like materials must not be dried on a heat setting Heated foam rubber materials can under certain circumstances produce fire by spontaneous combustion Do not allow children or pets to play on in or in front of the appliance Close supervision is necessary when the appliance is used near children and pets Before discarding or removing your dryer from service remove the door to the drying compartment to prevent children or animals from becoming trapped inside N Do not reach into the appliance when the drum is moving Do not install or store this appliance where it will be exposed to the weather Do not tamper with controls Do not repair replace or attempt to service any part of the appliance unless specifically recommended in the user repair instructions and you understand and have the skills to carry those out Do not use fabric softeners
24. load Close the door Select the appropriate cycle and options for the load see pages B 2 B 3 Press the Start Pause button The dryer indicator light will illuminate The estimated cycle time will appear in the display The time may fluctuate to better indicate drying time remaining in the cycle nenn e When the cycle is complete the Door Lock light will go out and End will appear in the display e Pressing Power cancels the cycle and stops your dryer e The Drying Cooling and Wrinkle Prevent indicator lights will illuminate during those portions of the cycle gS 22_ Operating Instructions Tips care and cleaning CONTROL PANEL Clean with a soft damp cloth Do not use abrasive substances Do not spray cleaners directly on the panel The control panel finish may be damaged by some laundry pre treatment soil and stain remover products Apply such products away from your dryer and wipe up any spills or overspray immediately TUMBLER Remove any stains such as crayon ink or fabric dye from new items such as towels or jeans with an all purpose cleaner Tumble old towels or rags to remove any excess stain or cleaning substance Once these steps are done stains may still be visible but should not transfer to subsequent loads STAINLESS STEEL TUMBLER To clean the stainless steel tumbler use a damp cloth with a mild non abrasive cleaner suitable for stainless steel surfaces Remove the cleaner residue
25. lored terminal block screw 4 Neutral wire white or center wire 5 3 4 1 9 cm UL listed strain relief If converting from a 4 wire electrical system to a 3 wire the ground strap must be wamne Feconnected to the terminal block support to ground the dryer frame to the neutral conductor gt 4 WIRE system connections 1 Remove the center terminal block screw 2 Connect the ground wire green or unwrapped of the power cord to the external ground conductor screw 3 Connect the neutral wire white or center wire of the power cord and the appliance ground wire green with yellow stripes under the central screw of the terminal block Connect the other wires to the outer terminal block screws Tighten screws Tighten the strain relief screws 6 Insert the tab of the terminal block cover into your dryer s rear panel slot Secure the cover with a hold down screw External ground connector Green or bare copper wire of power cord 3 4 in 1 9 cm UL listed strain relief Center silver colored terminal block screw Grounding wire green yellow 6 Neutral wire white or center wire With a level check your dryer and make necessary adjustments to the leveling legs At this time make sure all gas connections on gas models exhaust and electrical connections are complete Plug in your dryer and check operation by using the checklist below GAS MODELS ONLY The burner may not ignite initially due to air in the gas line Allowing yo
26. loset installation Mobile home installation Exhausting Gas requirements Electrical requirements Grounding Electrical connections Replacement parts and accessories Installation Final installation checklist Dryer Exhaust Tips Door Reversal Overview of the control panel Child lock My cycle Rack Dry Clean the lint filter Load the dryer properly Getting started Control Panel Tumbler Stainless Steel Tumbler Dryer Exterior Dryer Exhaust System Check these points if your dryer Information codes Fabric care chart Protecting the environment Declaration of conformity Specification Cycle chart Installing your dryer TOOLS NEEDED FOR INSTALLATION Hire a professional to install this dryer properly If there is a service call performed as a result of poor setup adjustment and connection it is considered the responsibility of the installer If you install the dryer you are responsible Make sure you have everything necessary for proper installation 1 A GROUNDED ELECTRICAL OUTLET is required See Electrical Requirements 2 A POWER CORD for electric dryers except Canada 3 GAS LINES if a gas dryer must meet national and local codes 4 EXHAUST SYSTEM must be rigid metal or flexible stiff walled metal exhaust ducting SEE EXHAUST REQUIREMENTS aaA p noA Guijyeysuy LO Control panel Door Adjustable leg SD Pliers Cutting knife Pipe wrench gas only
27. n 20 min 5 min Release Air Fluff No change 20 min 20 min Appendix _29 warranty SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product as supplied and distributed by SAMSUNG ELECTRONICS AMERICA INC SAMSUNG and delivered new in the original carton to the original consumer purchaser is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of One 1 Year All Parts and Labor Two 2 Years Control Board Parts This limited warranty begins on the original date of purchase and is valid only on products purchased and used in the United States To receive warranty service the purchaser must contact SAMSUNG for problem determination and service procedures Warranty service can only be performed by a SAMSUNG authorized service center The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG s authorized service center SAMSUNG will provide in home service during the warranty period at no charge subject to availability within the contiguous United States In home service is not available in all areas To receive in home service product must be unobstructed and accessible to the service agent If service is not available SAMSUNG may elect to provide transportation of the product to and from an authorized service center SAMSUNG will repair replace or refund this pro
28. not respond check the Child Lock indicator MY CYCLE Lets you activate your customized cycle that includes Dry Level Temp Time option etc By pushing the My Cycle button you activate the settings used during the previous My Cycle mode Default Normal Cycle If My Cycle mode is activated My Cycle lamp will be lit You can select all options in My Cycle mode as follows 1 Select cycle using Cycle Selector dial 2 After cycle selection set each option 14 Each cycle has certain default options that are automatically set To see these default options go to page F 3 3 Then you can start My Cycle by pushing the Start Pause button in My Cycle mode The cycle and options you select will be displayed the next time you choose My Cycle You can change the My Cycle settings by repeating same process above The last used setting will be displayed the next time you choose My Cycle 20_ Operating Instructions Tips RACK DRY Installing the drying rack 1 Open the dryer door 2 Position the drying rack in the tumbler placing the rear legs in the two recessed areas of the dryer s back wall 3 Place the front lip of the drying rack on top of the lint filter 4 Place the items to be dried on the rack leaving space between them so air can reach all surfaces Close dryer door a 6 Use the Time Dry cycle Select the time according to the moisture and weight of the items Start dryer It may be necessary
29. or products to eliminate static unless recommended for dryer use by the manufacturer of the fabric softener or product Clean the lint screen before or after each load Keep the area around the exhaust opening and surrounding areas free from lint dust and dirt The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel H This appliance must be properly grounded Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes See installation instructions for grounding this appliance Do not sit on top of the dryer Because of continuing product improvements Samsung reserves the right to change specifications without notice For complete details see the Installation Instructions packed with your product before selecting cabinetry making cutouts or beginning installation Ensure pockets are free from small irregularly shaped hard objects foreign material etc ie warn na COINS knives pins etc These objects could damage your dryer Do not wash clothing with large buckles buttons or other heavy metal or solid things 4_ Safety information A WARNING Gas leaks may occur in your system resulting in a dangerous situation Gas leaks may not be detected by smell alone Gas suppliers recommend you purchase and install a UL approved gas detector Install and use in accordance with the manufacturer s instructions
30. ow pad up or down until the desired time is displayed My Cycle Choose your favorite cycle including cycle temp dry level option etc See page 20 for detail Rack Dry Rack Dry is available at Time Dry cycle Temperature will be set only to Extra Low See page 21 for detail sd suononsysu Buieiado ZO Cycle Selector To select a cycle rotate the Cycle Selector dial to the desired cycle The indicator light by the cycle name will illuminate The Normal Heavy Duty Towels Perm Press and Delicates cycles are Sensor Dry cycles Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level very dry to damp dry is reached Normal Use this cycle to dry loads such as cotton underwear and linen Heavy Duty Use this cycle to get high heat for heavy fabrics such as jeans corduroys or work clothes Towels Dry loads such as bath towels Perm Press Dry wrinkle free cottons synthetic fabrics knits and permanent press fabrics automatically The cycle minimizes wrinkling by providing a longer unheated cool down period at the end of the cycle Delicates The Delicates cycle is designed to dry heat sensitive items at a low drying temperature Freshen Up This cycle removes odors and freshens garments Time Dry Time Dry allows you to select the desired cycle time in minutes Turn the Cycle Selector dial to Time Dry then press the Adjust Time up arrow to set the dr
31. proper dryer operation THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO WATER AND OR WEATHER THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS A DRYER PRODUCES COMBUSTIBLE LINT THE AREA AROUND THE DRYER SHOULD BE KEPT LINT FREE ALCOVE OR CLOSET INSTALLATION The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or warnine ClOSEt e No other fuel burning appliance should be installed in the same closet as the dryer e WARNING To reduce the risk of fire this dryer MUST BE EXHAUSTED TO THE OUTDOORS See EXHAUST INFORMATION section e Minimum clearances between the dryer and adjacent walls or other surfaces are 2 in front 17 on top 1 on either side and 2 375 in the back e The closet front must have two unobstructed air openings for a combined minimum total area of 72 in with 3 minimum clearance on the top and bottom A louvered door with equivalent space clearance is acceptable Installing your dryer _9 Installing your dryer MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR Part 32 80 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 1975 for the United States or CSA Standards Z240 for Canada When installing a d
32. rminal block A strain relief must be used Do not loosen the nuts already installed on the terminal block Be sure they are tight Use a 3 8 1cm deep well socket Review Gas Requirements section Remove the pipe thread protective cap Apply pipe joint compound or about 1 1 2 wraps of Teflon tape over all threaded connections Pipe joint compound must be resistant to the action of any liquefied petroleum gas Connect the gas supply to your dryer An additional fitting is required to connect the 3 4 1 9 cm female thread end of a flexible connector to the 3 8 1 cm male threaded end on the dryer Securely tighten the gas line fitting over threads Turn on the gas supply Check all gas connections for leaks using a soap solution If bubbles appear tighten the connections and recheck DO NOT use an open flame to check for gas leaks 14_ Installing your dryer 6 7 8 3 WIRE system connections 1 Loosen or remove the center terminal block screw 2 Connect the neutral wire white or center wire of the power cord to the center silver colored terminal screw of the terminal block Tighten screw 3 Connect the other wires to outer terminal block screws Tighten screws Tighten the strain relief screws 5 Insert the tab of the terminal block cover into your dryer s rear panel slot Secure the cover with a hold down screw 1 External ground connector 2 Neutral grounding wire green yellow 8 Center silver co
33. ryer in a mobile home provisions for anchoring the dryer to the floor must be made Locate an area that has adequate fresh air A minimum of 72 in 183 cm of unobstructed space is required Call 1 800 SAMSUNG for information on purchasing the Floor Anchoring Kit as an accessory All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure using materials that will not support combustion The exhaust duct may not terminate underneath the mobile home See Exhausting section for more information EXHAUSTING Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room In the United States e All dryers must be exhausted to the outside e Only a rigid or flexible metal duct should be used for exhausting In Canada e All dryers must be exhausted to the outside Outside the U S and Canada e Refer to local codes The dryer must be exhausted to the outside to reduce the risk of fire when installed in an warnine Alcove or closet NEVER USE A PLASTIC OR NON METAL FLEXIBLE DUCT If your existing ductwork is plastic non metal or combustible replace it with metal Use only a metal exhaust duct that is non flammable to ensure containment of exhaust air heat and lint 10_ Installing your dryer GAS REQUIREMENTS Use only natural or LP liquid propane gases THE INSTALLATION MUST
34. t make sure e The exhaust system meets all local state and national codes e That a flexible plastic duct is not used e To Inspect and clean all lint buildup from inside the existing duct e The duct is not kinked or crushed e The exhaust hood damper opens and closes freely The static pressure in any exhaust system must not exceed 0 83 inches of water column or be less than O This can be measured with the dryer running with a manometer at the point where the exhaust duct connects to the dryer A no heat setting should be used The dryer tumbler should be empty and the lint filter clean IMPORTANT TO INSTALLER Please read the following instructions carefully before installing the dryer These instructions should be kept for future reference aak p noA Guijyeysuy LO REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD warning SUFFOCATING LOCATION CONSIDERATIONS The dryer should be located where there is enough space in front for loading the dryer and enough space behind for the exhaust system This dryer is factory ready for rear exhaust To exhaust out the bottom or the left use the accessory exhaust kit Instructions are included with the kit It s important to make sure the room has enough fresh air The dryer must be located where there is no air flow obstruction On gas dryers adequate clearance as noted on the data plate must be maintained to ensure adequate air for combustion and
35. to reset the timer if a longer drying time is needed SUGGESTED ITEMS SUGGESTED TEMP SETTINGS Washable sweaters block to shape and lay flat on rack Heat Low Extra Low Stuffed toys cotton or polyester fiberfilled Heat Low Extra Low Stuffed toys Air Fluff foam or rubber filled Foam rubber pillows Air Fluff Sneakers Fluff or Heat Drying foam rubber plastic or rubber on a heat setting may cause damage to the item and warnine lead to a fire hazard Operating Instructions Tips _21 sd suononsysu Buieiado 20 operating Instructions tios CLEAN THE LINT FILTER e After each load e To shorten drying time e To operate more energy efficiently Do not operate your dryer without the lint filter in place LOAD THE DRYER PROPERLY e Place only one washload in your dryer at a time e Mixed loads of heavy and lightweight fabrics will dry differently which may result in lightweight fabrics being dry while heavy fabrics remaining damp at the end of a drying cycle e Add one or more similar items to your dryer when only one or two articles need drying This improves the tumbling action and drying efficiency e Overloading restricts tumbling action resulting in uneven drying as well as excessive wrinkling of some fabrics GETTING STARTED Load your dryer loosely DO NOT over
36. ur dryer to operate on a heat setting will purge the line If the gas does not ignite within 5 minutes turn your dryer off and wait 5 minutes Be sure the gas supply to your dryer has been turned on In order to confirm gas ignition check the exhaust for heat a or Go FINAL INSTALLATION CHECKLIST OOoOoago ogo Dryer is plugged into electrical outlet and properly grounded O Exhaust ductwork is hooked up and joints taped Plastic flexible duct is NOT used Used rigid or stiff walled flexible metal vent material Dryer is level with all legs firmly on the floor Gas models gas is turned on with no gas leaks Start your dryer to confirm that it runs heats and shuts off Installing your dryer _15 aaA p noA Guijyeysuy LO Installing your dryer DRYER EXHAUST TIPS A Plastic or non metal flexible duct presents a potential fire hazard WARNING 1 Let your dryer exhaust the air easily 2 Use 4 diameter rigid metal duct Tape all joints including at the dryer Never use lint trapping screws 3 Keep ducts as straight as possible 4 Clean all old ducts before installing your new dryer Be sure vent flap opens and closes freely Inspect and clean the exhaust system annually Don t let a poor exhaust system slow drying by 1 Restricting your dryer with a poor exhaust system 1 2 Using a plastic thin foil or non metal flexible duct 3 Using unnecessarily
37. voltage or supply light bulbs house fuses house wiring cost of a service call for instructions or fixing installation errors SAMSUNG does not warrant uninterrupted or error free operation of the product 30_ Warranty EXCEPT AS SET FORTH HEREIN THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS OR ANY OTHER SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE MISUSE OR INABILITY TO USE THIS PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE WITHOUT LIMITING THE FOREGOING PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS DAMAGE OR INJURY TO PURCHASER AND PURCHASER S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE MISUSE OR INABILITY TO USE THIS PRODUCT THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRO
38. ying time Press the arrow repeatedly to scroll through the time settings Wrinkle Release The Wrinkle Release cycle will release wrinkles from items that are clean dry and only slightly wrinkled such as clothes from a crowded closet suitcase or items that have been in the dryer too long after the cycle has ended Wrinkle Release can be used with any temperature selection Air Fluff The Air Fluff cycle tumbles the load in room temperature air Start Pause selection button Press to pause and restart programs 10 Power button Press once to turn your dryer on press again to turn it off If your dryer is left on for more than 10 minutes without any buttons being touched the power automatically turns off Operating Instructions Tips _19 operating Instructions tios CHILD LOCK A function to prevent children from playing with your dryer Setting Releasing If you want to set or release the Child Lock press both the Time and Signal buttons simultaneously for 3 seconds How to Set 1 It can be set while your dryer is running 2 Once you set the Child Lock function no button except for the Power button can be controlled until you release the Child Lock function 3 The Child Lock indicator will be lit 14 1 If the dryer is powered on again the Child Lock function stays on 2 To release that function follow the instructions above When other buttons except for the Power button do
39. ymbols ensures consistency among garment manufacturers of domestic and imported items Follow care label directions to maximize garment life and reduce laundering problems g 5 gt Warning Symbols for 5 Wash Cycle Special Instructions Laundering 3 ww Normal i Line Dry Hang to Dry Do Not Wash et Permanent Press 7 wrinkle Resistant m Drip Dry gt Do Not Wring Wrinkle Control w Gentle Delicates Dry Flat A Do Not Bleach 4 Hand Wash Heat Setting St Do Not Tumble Dry No Steam added to Water Temperature High GA iron eee Hot Medium z4 Do Not Iron ee Warm Low Dryclean Cold e Any Heat O Dry Clean Bleach No Heat Air x Do Not Dry Clean Any Bleach when Iron Dry or Steam al Ol needed Temperatures Line Dry Hang to Dry Only Non Chlorine color safe fA High m Drip Dry Bleach when needed Dry Flat lol Tumble Dry Cycle CA Medium Normal cA Low Permanent Press Wrinkle Resistant Wrinkle Control lO Gentle Delicates The dot symbols represent appropriate wash water temperatures for various items The temperature range for Hot is 105 125 F 41 52 C for Warm 85 105 F 29 41 C and for Cold 60 85 F 16 29 C Wash water temperature must be a minimum of 60 F 16 C for detergent activation and effective
Download Pdf Manuals
Related Search