Samson XP510I DJ Equipment User Manual
Contents
1. ine Using a Microphone e Be sure that the XP510i s Power switch is set to the OFF position e Turn all of the channel VOLUME VOL controls fully counterclockwise to the 0 position e If the speakers are not connected connect the speaker wires as described in the previous section e Next connect the power cable to an AC outlet e Using a standard XLR cable plug a microphone into the XP510i s Channel 1 MIC INPUT DAPI Jo AANI See 0 0 0 00 sae EXPEDITION N yo Se e eee Cd e Switch the XP510i s Power switch to the ON position e Set the MIC LINE switch to the MIC position e Set the Channel 1 VOLUME VOL control to about halfway e While speaking into the microphone slowly raise the MASTER level control until you have reached the desired level XP510i Quick Start cont d Using a Line Level Signal e Be sure that the XP510i s Power switch is set to the OFF position e Turn all of the channel VOLUME VOL controls fully counterclockwise to the 0 position e Connect the power cable to an AC outlet e If using channels 1 4 set the MIC LINE switch to the LINE position e Using standard2. IMPORTANT NOTE To avoid a loud pop be sure to turn down the MASTER level control before plugging and unplugging the mic cables when the phantom power is active 21 POWER LED indicator The Power LED will illuminate when the MAIN power switch is turned on Applying Reverb The XP510i features built in high quality 24 bit Reverb Effects that you can add to channels 1 through 4 You can use the reverb to create a studio effect by simply following the steps below 1 Connect a mic or instrument to the desired channel and adjust the volume and equalizer to your liking 2 Use the Reverb Program selector to choose one of the ten built in digital effects REVERB mm REVERB E a REVERB 3 Press the REVERB switch down on the channel to which you want to mF the os effect REVERB REVERB Cm 4 Once you have selected the channel s for effects by using the channel REVERB switch raise the REVERB main VO REVERS REVERB 5 O _ level control to apply the amount of reverb desired REVERB O _ REVERB oO _ VO REVERS REVERB 5 CEE i XP510i System Set ups saan R dye eseeeeTDooceee oooO n a a a a a a C Sconeeecececes seeresesagesesese o o o SAMSON 2 4 23F AY eel XP510i PORTABLE PA SYSTEM REVERB PROGRAMS SLAPBACK W VE a ECHO LONG VERE SLOW ST CHOR
3. tali da costituire un possibile rischio di scariche elettriche dannose per le persone Il punto esclamativo all interno di un triangolo equilatero avvisa l utente della presenza di importanti istruzioni di manutenzione assistenza nella documentazi one che accompagna il prodotto Importanti Istruzioni di Sicurezza 1 Prima di usare l apparecchio vi preghiamo di leggerne per intero le istruzioni 2 Conservate tali istruzioni per una eventuale consultazione futura 3 Vi preghiamo di rispettare tutte le istruzioni di sicurezza 4 Seguite tutte le istruzioni del costruttore 5 Non usate questo apparecchio vicino ad acqua o umidit 6 Pulite l apparecchio esclusivamente con un panno asciutto 7 Evitate di ostruire una qualsiasi delle aperture di ventilazione Posizionatelo seguendo le istruzioni del costruttore 8 Non posizionatelo vicino a sorgenti di calore come radiatori scambiatori di calore forni o altri ap parecchi amplificatori compresi in grado di generare calore 9 Non disattivate la protezione di sicurezza costituita dalla spina polarizzata o dotata di collegamento a terra Una spina polarizzata dotata di due spinotti uno pi piccolo ed uno pi grande Una spina dotata di collegamento a terra dotata di due spinotti pi un terzo spinotto di collegamento a terra Questo terzo spinotto eventualmente anche pi grande viene fornito per la vostra sicurezza Se la spina fornita in dotazione non si adatta alla vostra
4. Channel Equalization lt 0 1 14 dB 20 Hz 20 kHz MONITOR L R REC L R 10 kQ HIGH 10 kHz shelving 15 dB LOW 100 Hz shelving 15 dB Frequency Response 20 Hz 20 kHz 1 dB 10 kQ MONITOR L R 20 Hz 20 kHz 0 1 dB 10 kQ REC L R LIMIT COMP Switch DOWN Comp UP Limit CH1 2 Hum and Noise Input GAIN Maximum Input sensitivity MIC Phantom Power 112dBu equivalent input noise Rs 1500 15V DC 90dBu Residual noise MONITOR L R all Levels at Minimum 80dBu MONITOR at nominal level and all channel Levels Power Source Power Consumption minimum AC INPUT 100 V 240 V 50 60 Hz 600 W MAX 70dBu MONITOR at maximum level and all channel Levels minimum Weight 52 8 Ib 24 Kg Maximum Voltage Gain 50dB MIC 1 2 XLR LIMIT Position INTO MONITOR L R 60dB MIC 3 4 XLR INTO MONITOR L R 40dB MIC 1 2 PHONE TRS LIMIT Position INTO MONITOR L R 50dB MIC 3 4 PHONE TRS INTO MONITOR L R 14dB CH 1 2 LINE PHONE TRS LIMIT Position MIC LINE SWIN INTO Where 0 dBu 0 775 Vand 0 dBV 1 V MONITOR L R 24dB CH 3 4 LINE PHONE TRS MIC LINE SW IN INTO MONITOR L R 28dB ST LINE INTO MONITOR L R 48dB MIC 3 4 XLR INTO REC L R Dimensions 22 7 W x 12 6 D x 22 H 577 mm W x 320 mm D x 560 mm H Input Specifications Input Connector Input Impedance Nominal Source Rated Input Level Connector Type Impedance CH MIC 3 6 kQ 7 5 KQ 50 600 0 600 32 dBu 22dBu XLR Type Balanced Phone Jack TRS T Hot R Cold S GND CH L
5. The XP510i is the ultimate in portable design The lightweight and clever design allow you to connect all the pieces together into a single easy to move case e The mixer is stored in one of the speaker cabinets the other cabinet has an accessory compartment for storing the speaker cables microphones etc e The speakers are 2 way vented enclosures with 10 inch woofers for deep bass complimented by a 1 inch high frequency driver set in a custom horn with a 60 x 90 degree coverage pattern producing a clean clear sound e The internal 2 x 250 watt lightweight Class D power amplifier produces a powerful stereo sound e The XP510i s mixer can be removed from the speaker for tabletop use and you can use the kick stand to set the mixer at an ergonomically correct angle e The 10 channel mixer features four Mic Line inputs allowing you to connect microphones or line signals plus three stereo inputs for connecting line signals from keyboards drum machines and MP3 CD players You can engage the Phantom Power switch if you are using condenser microphones e On each of the mixer s channel inputs there is a Bass and Treble control allowing you to equalize the tone of the individual inputs e To create a lush sound on any of the microphone channels you can select from the ten onboard 24 bit digital effects e The XP510i features a built in iPod dock allowing you to easily connect most iPod models for seamless music playback You can use the
6. iPod to simply play music add background tracks or repeat a commercial message at a fair or trade show e For added flexibility the XP510i s mixer has a Monitor Out on two 1 4 inch jacks allowing you to connect to exter nal powered monitor speakers XP510i Quick Start Unpacking and Setting Up the XP510i e Unpack all the system components from the shipping carton and save all packing materials in the unlikely event your unit ever needs to be returned for service e Remove the mixer by turning the quarter turn screw counterclockwise towards the RELEASE position e Remove the accessory compartment cover by turning the quarter turn screw counterclockwise towards the RELEASE position and remove the included speaker cables e Replace the accessory panel by aligning the bottom of the panel into the slots make sure the quarter turn screw is in the RELEASE position then close the panel and turn the quarter turn screw clockwise to LOCK e Position the speakers on the floor or on stands and using one of the included speaker cables connect the mixer s LEFT SPEAKER OUT to the left speaker s input connector Next use the second included speaker cable to connect the RIGHT SPEAKER OUT to the right speaker s input connector s e ii E s70 Sor i z j X eleeg Slow MMI
7. 14 inch cables connect a line level signal from a keyboard into the XP510i s LINE INPUTS Keyboard I o EEE NAA Maa KABIN ueta fa YV DABIS Electric Acoustic Guitar Ka Q gt a MONITOR Re 7 8 s710 our a mono A oo B a jHN MEN CY VY A s i 2 N f C_ y a WY SAA SA ee irag a O Sea oet E Bes a 4 a RN ee at x z F 3 A 7 y 7 eo e 5 AA x e e eo E EXPEDITION NS ain ee o_o o e o 02020 o e e e z AN P e Switch the XP510i s Power switch to the ON position e Play your guitar or keyboard and slowly raise the channel control and the MASTER level control until you have reached the desired VOLUME Configuring the XP510i for Transport You can easily carry your sound system using the XP510i s Slide and Lock feature The Slide and Lock speaker enclosures allow you to connect both speakers together into a single easy to carry unit Follow these steps to configure the XP510i for easy transport 3 Slide the second speaker into the speaker on the floor making certain that the two speakers stay parallel to each other 7 Place one speaker on the floor and set it on its side q a z 2 Position the second speaker above the first sp
8. ALL 210 100 MI Block Diagram 32dBu to 14dBu MIC XLR 6dBu to 12dBu LINE XLR P come Inputs CH1 2 22dBu to 4dBu MIC TRS o o 4dBu to 22dBu LINE TRS PAD 18dB L mc c tine 32dBu to 6dBu MIC XLR 6dBu to 20dBu LINE XLR o papizede Inputs Duez une CH3 4 22dBu to 4dBu MIC TRS 4dBu to 30dBu LINE TRS Inputs CH5 8 a AN OdBu R E o p Inputs CH9 10 OdBu o o CH 9 10 REVERB PROGRAM PROGRAM ii ay ae 4 a ie i T 5 o a me o o a 0 T T 3 o z e i i i I 1 1 nn x x O eos SELECT c o p o EXPEDITION L L R oa eae TWEETER SPEAKER OUT WOOFERX TWEETER Safety Instructions Consignes de s curit Sicherheitsvorkehrungen WARNING CAUTION DO NOT EXPOSE THIS EQUIPMENT FOR CONTINUED PROTECTION AGAINST RISK CA UTION TO RAIN OR MOISTURE OF FIRE REPLACE ONLY WITH SAME TYPE FUSE RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRONIQUE UTILISER UN FUSIBLE DE DO NOT OPEN NE PAS OUVRIR RECHANGE DE M ME TYPE AVIS ATTENTION WARNING To reduce the risk of fire or electric shock do not expose this unit to rain or moisture To reduce the hazard of electrical shock do not remove cover or back No user serviceable parts inside Please refer all servicing t
9. INE 3 6 kQ 7 5 kQ 50 6000 6000 6 dBu 4 dBu XLR Type Balanced Phone Jack TRS T Hot R Cold S GND M INPUT 600 Q Unbalanced Phone Jack Output Specifications eea Connector Output Impedance Nominal Load Rated Output Connector type Impedance Level MONITOR kasan gt 10 kQ 4 dBu Phone Jack TRS Impedance bal anced T hot R Cold S ETE RECOUT OUT 600 6000 gt 10 OO 0k O 4 4dBu O RCA pin RCApinJack Specifications and design subject to change without notice Dimensions 88 a AUU In Hl f ol EL ENE Spog SAMSON 24 08 XP510i Mixer Layout CISA Se E SPEECH XP510i PORTABLE PA SYSTEM MUSIC CHS 1 Channel Input Jacks channels 1 4 MIC XLR connector Use these XLR jacks to connect low impedance microphones to the XP510i s built in mic preamps LINE 1 4 inch phone connector Use these 1 4 jacks to connect instrument or audio sources with line level signals to the XP510i You can connect the outputs from acoustic guitar pickups keyboards drum machines CD MP3 TAPE players and other units with line level outputs here 2 Stereo Channel Input Jacks channels 5 6 7 8 9 10 For stereo inputs use the LINE L to connect the left channel and the LINE R to connect the right chan nel Use these inputs to connect high impedance microphones synthesizers drum machines MP3 CD tape players or any
10. JIN EXPEL 1 5 l PORTABLE PA SYSTEM B l a Owners Manual EN SAMSON Introduction Thank you for purchasing the Expedition XP510i PORTABLE PA SYSTEM from Samson The XP510i features a com pact 10 channel mixer with 500 watts of onboard power and dual 2 way speakers making it an ideal solution for a variety of small to medium sized PA applications The XP510i is extremely portable thanks to its lightweight and unique Slide and Lock design The 10 channel mixer can be removed from the speaker for tabletop use It features 4 inputs for connecting micro phones plus three inputs for connecting stereo signals like those from a CD player or electronic keyboard There s also a built in 24 bit digital effects processor to add studio quality effects to your voice or instruments For music playback the XP510i features a convenient iPod dock The mixer also provides a robust output with 500 watts of total power from the lightweight Class D amplifier section The XP510i employs a matched speaker system with dual 2 way enclosures that have proprietary 10 inch woofers and 1 inch high frequency drivers To help project the sound to a larger audience the XP510i speakers can be mounted on standard speaker stands thanks to the integral pole mount receptacles The XP510i is constructed using durable ABS high impact plastic making it super road tough and at the same time lightweight In this manual you ll find a de
11. eaker and line up the Slide and Lock tracks and grooves so that they are parallel to the speaker on the floor 4 You will feel a slight click when the two speakers are in place RNOSELNMAS Speaker cabinets must be reversed with respect to top and bottom XP510i Wiring Guide CONNECTING THE XP510i There are several ways to interface the XP510i to support a variety of applications The XP510i features balanced inputs and outputs so connecting balanced and unbalanced signals is possible Unbalanced 1 4 Connector Signal Signal Tip signal S sl 3 Ground Ground Gii Sleeve ground Balanced TRS 1 4 Connector l Signal ring Tip sigr tip Signal tip Ring signal J a O a Ground XLR Balanced Wiring Guide Common 1 Hot Hot Common ground ground 2 Ground Sleeve ground QE Solder Points End View Cold Eamala YIR Cold 3 Hot 2 Common 1 Hot 2 ground Common ground o Q End View Solder Points Cold 3 Cold Male XLR Specifications System Specifications Maximum Output Power 250W 250W 8Q Crosstalk at 1 kHz 70 dB between input channels 70 dB between input output channels Maximum Output Level 0 5 T H D 1kHz 22dBu MONITOR L R 10 kQ SPEECH MUSIC 14 dBu REC 10 kO 167 Hz 3dB Octave T H D Input
12. ez les instructions du fabricant 5 Ne pas utiliser cet appareil pr s d une source liquide ou dans un lieu humide 6 Nettoyez l appareil uniquement avec un tissu humide 7 Veillez a ne pas obstruer les fentes pr vues pour la ventilation de l appareil Installez l appareil selon les instructions du fabricant 8 Ne pas installer pr s d une source de chaleur radiateurs etc ou de tout quipement susceptible de g n rer de la chaleur amplificateurs de puissance par exemple 9 Ne pas retirer la terre du cordon secteur ou de la prise murale Les fiches canadiennes avec polarisa tion avec une lame plus large ne doivent pas tre modifi es Si votre prise murale ne correspond pas au mod le fourni consultez votre lectricien 10 Prot gez le cordon secteur contre tous les dommages possibles pincement tension torsion etc Veillez ce que le cordon secteur soit libre en particulier sa sortie du bo tier 11 D connectez l appareil du secteur en pr sence d orage ou lors de p riodes d inutilisation prolon g es 12 Consultez un service de r paration qualifi pour tout dysfonctionnement dommage sur le cordon secteur baisse de performances exposition la pluie projection liquide dans l appareil introduction d un objet dans le bo tier etc ACHTUNG Um die Gefahr eines Brandes oder Stromschlags zu verringern sollten Sie dieses Ger t weder Regen noch Feuchtigkeit aussetzen Um die Gefahr eines Stromschlags zu ver
13. ication is mainly for MUSIC press the switch down to select the MUSIC response curve If your application is mainly for SPEECH leave the switch up to select the SPEECH response curve 15 MONITOR control knob The MONITOR volume control is used to control the overall level sent to the MONITOR OUT which can be used to send to a second set of powered speakers for monitors 16 REVERB PROGRAM selector This control knob is used to select one of ten 24 bit DSP effects programs 17 REVERB control knob The REVERB control knob is used to adjust the total amount of reverb added to any channel that has its REVERB switch see 6 pressed down 18 MASTER control knob The MASTER volume knob controls the overall output level This knob determines the final output signal level Signals from all ten channels are routed here just before being routed to the built in power amplifiers and Left and Right speaker output jacks see 10 19 METER LED indicators This six segment bar meter shows the XP510i s output level For optimum signal to noise ratio set the VOLUME control so that program material is usually at or around 3 to 6 VU with occasional but not steady excursions to the red LIMIT segment 20 PHANTOM switch The XP510i features an onboard Phantom power supply to operate condenser microphones When the switch is engaged the LED will illuminate indicating that phantom power is now available on the micro phone pre amps
14. il tero pretende advertir al usuario de la presencia de voltajes peligrosos no aislados dentro de la carcasa del producto que pueden ser de la magnitud suficiente como para constituir un riesgo de descarga el ctrica a las personas El s mbolo de exclamaci n dentro del tri ngulo equil tero quiere advertirle de la existencia de importantes instrucciones de manejo y mantenimiento reparaciones en los docu mentos que se adjuntan con este aparato Instrucciones importantes de seguridad 1 Lea todo este manual de instrucciones antes de comenzar a usar la unidad 2 Conserve estas instrucciones para cualquier consulta en el futuro 3 Cumpla con todo lo indicado en las precauciones de seguridad 4 Observe y siga todas las instrucciones del fabricante 5 Nunca utilice este aparato cerca del agua o en lugares h medos 6 Limpie este aparato solo con un trapo suave y ligeramente humedecido 7 No bloquee ninguna de las aberturas de ventilaci n Instale este aparato de acuerdo a las instruc ciones del fabricante 8 No instale este aparato cerca de fuentes de calor como radiadores calentadores hornos u otros aparatos incluyendo amplificadores que produzcan calor 9 No anule el sistema de seguridad del enchufe de tipo polarizado o con toma de tierra Un enchufe polarizado tiene dos bornes uno m s ancho que el otro Uno con toma de tierra tiene dos bornes normales y un tercero para la conexi n a tierra El borne ancho o el tercero
15. ing and thus prevent potential negative effects on the environment and human health THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION SUITABLE FOR HOME OF OFFICE USE Copyright 2010 Samson Technologies Corp Samson Technologies Corp 45 Gilpin Avenue Hauppauge New York 11788 8816 Phone 1 800 3 SAMSON 1 800 372 6766 Fax 631 784 2201 www samsontech com V1 6
16. m being walked on and pinched particularly at plugs convenience receptacles and at the point at which they exit from the unit 11 Unplug this unit during lightning storms or when unused for long periods of time 12 Refer all servicing to qualified personnel Servicing is required when the unit has been damaged in any way such as power supply cord or plug damage or if liquid has been spilled or objects have fallen into the unit the unit has been exposed to rain or moisture does not operate normally or has been dropped ATTENTION Pour viter tout risque d lectrocution ou d incendie ne pas exposer cet appareil a la pluie ou a l humidit Pour viter tout risque d lectrocution ne pas ter le couvercle ou le dos du bo tier Cet appareil ne contient aucune pi ce remplacable par l utilisateur Confiez toutes les r parations a un personnel qualifi Le signe avec un clair dans un triangle pr vient l utilisateur de la pr sence d une tension dangereuse et non isol e dans l appareil Cette tension constitue un risque d lectrocution Le signe avec un point d exclamation dans un triangle pr vient l utilisateur d instructions importantes relatives a l utilisation et a la maintenance du produit Consignes de s curit importantes 1 Veuillez lire toutes les instructions avant d utiliser l appareil 2 Conserver ces instructions pour toute lecture ult rieure 3 Lisez avec attention toutes les consignes de s curit 4 Suiv
17. n polarisierter Stecker hat zwei flache unterschiedlich breite Pole Ein geerdeter Stecker hat zwei flache Pole und einen dritten Erdungsstift Der breitere Pol oder der dritte Stift dient Ihrer Sicherheit Wenn der vorhandene Stecker nicht in Ihre Steckdose passt lassen Sie die veraltete Steckdose von einem Elektriker ersetzen 10 Sch tzen Sie das Netzkabel dahingehend dass niemand dar ber laufen und es nicht geknickt werden kann Achten Sie hierbei besonders auf Netzstecker Mehrfachsteckdosen und den Kabelan schluss am Ger t 11 Ziehen Sie den Netzstecker des Ger ts bei Gewittern oder l ngeren Betriebspausen aus der Steck dose 12 berlassen Sie die Wartung qualifiziertem Fachpersonal Eine Wartung ist notwendig wenn das Ger t auf irgendeine Weise beispielsweise am Kabel oder Netzstecker besch digt wurde oder wenn Fl ssigkeiten oder Objekte in das Ger t gelangt sind es Regen oder Feuchtigkeit ausgesetzt war nicht mehr wie gewohnt betrieben werden kann oder fallen gelassen wurde Instrucciones de seguridad Istruzioni di Sicurezza PRECAUCION Para reducir el riesgo de incendios o descargas no permita que este aparato quede expuesto a la lluvia o la humedad Para reducir el riesgo de descarga el ctrica nunca quite la tapa ni el chasis Dentro del aparato no hay piezas susceptibles de ser reparadas por el usuario Dirija cu alquier reparaci n al servicio t cnico oficial El s mbolo del rel mpago dentro del tri ngulo equ
18. o qualified personnel The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompa nying the product Important Safety Instructions 1 Please read all instructions before operating the unit 2 Keep these instructions for future reference 3 Please heed all safety warnings 4 Follow manufacturers instructions 5 Do not use this unit near water or moisture 6 Clean only with a damp cloth 7 Do not block any of the ventilation openings Install in accordance with the manufacturers instruc tions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or third prong is provided for your safety When the provided plug does not fit your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord fro
19. other line level device The XP510i features both 1 4 phone and RCA connectors 3 MIC LINE switch channels 1 4 The MIC position changes the gain of both input jacks to MIC level The LINE position reduces the gain of both jacks by 30dB to line level 4 LIMIT COMP switch Set the LIMIT COMP switch to the COMP position to apply compression or set it to the LIMIT position to apply limiting 5 Equalizer control knobs HIGH FREQUENCY HF The HF knob controls the amount of Treble applied to each channel The chan nel s HIGH frequency response is flat when the knob is in the 12 00 position Rotating the knob to the right will boost the channel s high frequency response above 10 kHz by 15 dB and rotating it towards the left will cut the high frequency response by 15 dB LOW FREQUENCY LF The LF knob controls the amount of Bass applied to each channel The channel s LOW frequency response is flat when the knob is in the 12 00 position Rotating the knob to the right will boost the channel s low frequency response below 100 Hz by 15 dB and rotating it towards the left will cut the low frequency response by 15 dB 6 REVERB switch Use the REVERB switch to add an effect to a Mic or Line input on any of the inputs 1 4 The REVERB LED indicator lights GREEN when the REVERB is ON 7 VOLUME control knob This knob sets the overall level for the Mic or Line input NOTE To reduce noise set the VOLUME cont
20. presa consultate un elettricista per la sostituzione della presa obsoleta 10 Proteggete il cavo di alimentazione in modo che non sia possibile camminarci sopra n piegarlo con particolare attenzione alle prese ai punti di collegamento e al punto in cui esce dall apparecchio 11 Staccate l apparecchio dalla alimentazione in caso di temporali o tempeste o se non lo usate per un lungo periodo 12 Per l assistenza fate riferimento esclusivamente a personale qualificato necessaria l assistenza se l apparecchio ha subito un qualsiasi tipo di danno come danni al cavo o alla spina di alimentazione nel caso in cui sia stato versato del liquido o siano caduti oggetti al suo interno sia stato esposto a pioggia o umidit non funzioni correttamente o sia stato fatto cadere If you want to dispose this product do not mix it with general household waste There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment recovery and recycling Private household in the 25 member states of the EU in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer if you purchase a similar new one For Countries not mentioned above please contact your local authorities for a correct method of disposal By doing so you will ensure that your disposed product undergoes the necessary treatment recovery and recycl
21. ringern sollten Sie weder Deckel noch R ckwand des Ger ts entfernen Im Innern befinden sich keine Teile die vom Anwender gewartet werden k nnen Uberlassen Sie die Wartung qualifiziertem Fachpersonal Der Blitz mit Pfeilspitze im gleichseitigen Dreieck soll den Anwender vor nichtisolierter gef hrlicher Spannung im Ger teinnern warnen Diese Spannung kann so hoch sein dass die Gefahr eines Stromschlags besteht Das Ausrufezeichen im gleichseitigen Dreieck soll den Anwender auf wichtige Bedienungs und Wartungsanleitungen aufmerksam machen die im mitgelieferten Informationsmaterial n her beschrieben werden Wichtige Sicherheitsvorkehrungen 1 Lesen Sie alle Anleitungen bevor Sie das Ger t in Betrieb nehmen 2 Bewahren Sie diese Anleitungen f r den sp teren Gebrauch gut auf 3 Bitte treffen Sie alle beschriebenen Sicherheitsvorkehrungen 4 Befolgen Sie die Anleitungen des Herstellers 5 Benutzen Sie das Ger t nicht in der N he von Wasser oder Feuchtigkeit 6 Verwenden Sie zur Reinigung des Ger ts nur ein feuchtes Tuch 7 Blockieren Sie keine Bel ftungs ffnungen Nehmen Sie den Einbau des Ger ts nur entsprechend den Anweisungen des Herstellers vor 8 Bauen Sie das Ger t nicht in der N he von W rmequellen wie Heizk rpern W rmeklappen fen oder anderen Ger ten inklusive Verst rkern ein die Hitze erzeugen 9 Setzen Sie die Sicherheitsfunktion des polarisierten oder geerdeten Steckers nicht au er Kraft Ei
22. rols on any unused channels to the minimum setting 8 MONITOR OUT jacks The signal present at the MONITOR OUT jacks is sent from the MONITOR level control knob which is fed from the input channels The MASTER control does not affect the MONITOR OUT signal 9 REC OUT jacks This output is used to send the main mix to an external recorder The signal present at this connector is the L R bus signal before it has passed through the MASTER level control The nominal output level is 10 dBV and the impedance is 100 Ohms 7 SLAPB 8 ECHO CONGA Vena 9 KAASA sa eal 20 10 SPEAKER OUT jacks The XP510i has two 1 4 inch phone connectors which are powered outputs used to connect your left and right speaker Use the included speaker cables to con nect the speakers CAUTION The total impedance load for each side of the amplifier must not be less than 8 Ohms Do not connect additional speakers to the XP510i mixer 11 AC IEC inlet Connect the supplied heavy gauge 3 pin IEC power cable here 12 POWER switch Use the POWER switch to turn power to the XP510i on or off 13 iPOD DOCK The XP510i has a built in iPod dock which can be used to connect most of the latest iPod models The iPod sig nal is controlled by the Channel 9 10 VOLUME control 14 SPEECH MUSIC switch The SPEECH MUSIC switch is used to change the over all frequency response or tone contour for the XP510i sound system If your appl
23. se incluyen como medida de seguridad Cuando el enchufe no encaje en su salida de corriente llame a un electricista para que le cambie su salida anticuada 10 Evite que el cable de corriente quede en una posici n en la que pueda ser pisado o aplastado especialmente en los enchufes recept culos y en el punto en el que salen de la unidad 11 Desconecte de la corriente este aparato durante las tormentas el ctricas o cuando no lo vaya a usar durante un periodo de tiempo largo 12 Dirija cualquier posible reparaci n solo al servicio t cnico oficial Deber hacer que su aparato sea reparado cuando est da ado de alguna forma como si el cable de corriente o el enchufe est n da ados o si se han derramado l quidos o se ha introducido alg n objeto dentro de la unidad si esta ha quedado expuesta a la lluvia o la humedad si no funciona normalmente o si ha ca do al suelo ATTENZIONE per ridurre il rischio di incendio o di scariche elettriche non esponete questo ap parecchio a pioggia o umidit Per ridurre il pericolo di scariche elettriche evitate di rimuoverne il coperchio o il pannello posteriore Non esistono all interno dell apparecchio parti la cui regolazione a cura dell utente Per eventuale assistenza fate riferimento esclusivamente a personale qualificato II fulmine con la punta a freccia all interno di un triangolo equilatero avvisa l utente della presenza di tensioni pericolose non isolate all interno dell apparecchio
24. tailed description of the features of the XP510i PA system as well as a description of its front and rear panels step by step instructions for its setup and use and full specifications You ll also find a war ranty card enclosed please don t forget to fill it out and mail it in so that you can receive online technical support and so we can send you updated information about these and other Samson products in the future Also be sure to check out our website www samsontech com for complete information about our full product line With proper care and adequate air circulation your XP510i will operate trouble free for many years We recommend you record your serial number in the space provided below for future reference Serial number Date of purchase ____ o Z o o oo Should your unit ever require servicing a Return Authorization number RA must be obtained before shipping your unit to Samson Without this number the unit will not be accepted Please call Samson at 1 800 3SAMSON 1 800 372 6766 for a Return Authorization number prior to shipping your unit Please retain the original packing materials and if possible return the unit in the original carton and packing materials If you purchased your Sam son product outside the United States please contact your local distributor for warranty information and service Features e The XP510i is a compact PA system with dual 2 way speakers onboard mixer and 500 watt power amplifier e
Download Pdf Manuals
Related Search