Revolabs 01-ELITEEXEC4 Microphone User Manual
Contents
1. ccccccceeeeeeeeceeesceteenaausceeeesaeesceeessueaseeeessaaaeeeeeesaeees 9 Using the HD Omni Directional Tabletop Wireless Boundary Microphones s0sccecseeeeeeeeeeeeens 10 Using the HD Directional Tabletop Wireless Boundary Microphones ccccecseecceeeeeeceeeeeeeeeeaeeeeeees 12 Using the HD XLR Microphone Wireless Adapter ccccccceeceecceseseceeeceeeeeeeeeesaaeeeeesseeseeeeeeaeeeeeessaaees 13 Using the HD Wireless Adapter for Countryman Microphone cccccsseeeeeeeeeeeeeeeeeeaaueseeeseuaeeseeseaaaees 14 Pairing Wireless Microphones to Base Station ccccccsccccccsseeceeeceeeeeeeeeeaeeeeeeeesseeeeeeseeaaadeeeeesseeeeeeeeeas 15 Revolabs HD Venue Charger BaS cccccccscccessese MEP oaoa ARDS reese 16 0000 ee ane 16 Charging the Microphone Batteries cccccccccccccsesseceeccseuseetecsdensececscseeeeeesseaaeceeesseaeeceessseaeeeeessaaeeeess 16 Updating the Revolabs HD Firmware im ssssccscsscsseccerses MMMM sccsceseceessesseccersessecsersesseetersessentensees 17 Revolabs HD Indicator LEDs SIRS eee OO eee eeecceesaeesaeeseaesoesseeesoaesoessoeeeoeees 18 EC i Cee 19 SDOCIICATIONS iiss ccin EET OERE E E eee 20 Safety and General Information Please read the following information to ensure safe and efficient use of your Revolabs system FCC User Information FCC Registration Number 0014898290 FCC ID T5V01HDEXEMIC Revolabs HD Mi2. Solid GREEN Charging Complete Charger Base battery discharged every 1 5 seconds every 1 5 seconds every 1 5 seconds 1 5 seconds powering down GREEN and RED GREEN and RED paired YELLOW flash GREEN Flashing Microphone low battery alternating with mic live GREEN flash YELLOW flash RED Flashing Microphone low battery alternating with two mic muted RED flashes Alternating RED O Searching for a connection or YELLOW GREEN out of radio range The Microphone will try to re establish the link for about 15 minutes and then turn off automatically O FF Rapid RED flashes FF Radio congestion it is not continuing for more possible to make a radio than a few seconds connection because there are already too many nearby users or there is heavy radio interference Possibilities include some types of digital wireless devices or other Revolabs installations FF Groups of five rapid O Unit is faulty Contact your AV RED flashes service provider for advice Warranty Revolabs Inc warrants this product to be free of manufacturing defects Repair or replacement of any defective part or unit at the discretion of the Seller will be free of charge for the period of one year Any attempt by the user to alter the equipment or equipment damaged by negligence accident or Acts of God voids this warranty The Seller shall not be liable for any consequential damage resulting from the malfunction of this product Should the user
3. clip also used to attach microphone to a lapel blouse or lanyard Mute Button press to mute un mute and pair microphone Acoustic Cover protects delicate microphone element non removable 6 LED display visual status for mute un mute and pairing Note Microphones in new systems must be paired to the Base Station with each microphone assigned to a unique channel on the base unit See pairing instructions below oe a Revolabs HD Wearable Microphones turn on and mute automatically when removed from Charger Base to reduce noise while being attached To use the HD Wearable Microphone 1 Remove the microphone from the Charger Base 2 Attach the microphone to clothing or to a lanyard position microphone just above the sternum or breastbone within 6 12 inches 15 30cm from the mouth is recommended Make sure microphone is attached securely with the microphone LED indicator pointed up toward mouth 3 With the microphone in the wearing position un mute the microphone by pressing and releasing the Mute button confirm by a flashing GREEN LED If the volume is too low move the microphone closer to the mouth 4 To turn microphones off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED then release button If the microphones are moved out of range of the Base Station 300 feet or 91 meters the connection will be dropped LED flashes
4. experience unsatisfactory performance from this equipment contact the Seller to obtain instructions for return or replacement as deemed necessary This warranty is not transferable by the original end user Revolabs Inc 63 Great Road Maynard MA 01754 www revolabs com 800 326 1200 Specifications Dimensions L W H and Weight HD Venue Base Station HD Charger Base Wireless Microphones Shipping Weight Radio Frequency 01 HDVENU and other HD products 03 HDVENUEU and other HD products 03 HDVENUCN and other HD products Connectors Base Station Audio Firmware Port Charger Base Microphone Power Requirements Base Station Charger Base Range Battery Charge Time Security Included Accessories 16 9 43 03 cm x 8 0 20 32 cm x 1 7 4 42 cm 2 0 Ibs 5 45 kg 4 6 11 75 cm x 3 125 7 9 cm x 1 0 2 54 cm 0 325 Ibs 0 147 kg Wearable 0 9 2 3 cm x 0 8 2 0 cm x 2 6 6 6 cm 0 05 Ib 0 02 kg TableTop 1 5 3 8 cm x 0 8 2 0 cm x 3 3 8 4 cm 0 05 Ib 0 02 kg XLR Adapter 0 9 2 3 cm x 0 8 2 0 cm x 4 0 10 2 cm 0 05 Ib 0 02 kg Countryman Adapter 1 5 3 8 cm x 0 8 2 0 cm x 3 3 8 4 cm 0 05 Ib 0 02 kg 2 0 Ibs 5 45 kg 1 92 to 1 93 GHz UPCS North America 1 88 to 1 90 GHz DECT EU 1 90 to 1 92 GHz Ys and XLR Balanced 2 In amp 2 Out Mini USB DC power input port Proprietary 4 pin microphone ch
5. Revolabs HD Venue Wireless Microphone System Models 01 HDVENU 03 HDVENUEU 03 HDVENUCH revolabs User and Set up Guide revo 2010 REVOLABS INC All rights reserved No part of this document may be reproduced in any form or by any means without express written permission from Revolabs Inc Product specifications are subject to change without notice Revolabs HD Venue Wireless Microphone System Manual 01 HDVNUMAN PAP 11 SEPT 2010 Rev 1 1 Contents Safety and General Information cccccccseeeccceceeeeeeeeeeeaeeeceeeeaeeseeeeeeseeeeeeeeseeseeeessseaeeeeeesseeeeeessaaseeeeessageeeees 1 LV OCA CTO Marn a cls cca secede sacs cs Sein melon es a aoe ata ode hase aeclax Pcs een a a aa 3 SV SUSI CG OOS NS ssrin cect oe ee emcee es cai ge ae Seetinesse a a ee secenast 3 Installing the Revolabs HD Venue Base Station cccccccccssccceeeceseeceececeueeseeecseeeeseesaueessueeseeesseeeseeeess 5 Sie nds ons glo ih Gio a aleve 6 ge gt airneo a a a Oe Me a ae ee ener 5 Configuring the Revolabs HD Venue Base Station c cccccccscsecesesesescscececceseseseevevevecacerersevevevavvenenensevens 7 Using the Rear Panel Configuration DIP Switches ccccccccecececceeeeeeeeceeeeceneesseeeeeessaeeseeeessaaeeeeessagees 7 Revolabs HD Microphones and HD Microphone Adaptelrs ccccccseeececeedeeeeeeesceesseeeeesseeeeeseeeeeesseeeesens 9 Using the HD Wearable Wireless Microphones
6. Station while in the Charger Base In normal use batteries should fully charge in about 2 hours but will quick charge to 80 capacity in approximately 1 hour and 20 minutes Fully charged microphones left in the Charger Base remain solid GREEN Updating the Revolabs HD Firmware Revolabs HD Systems are field upgradable for the firmware portion of the Base Station and microphones The firmware must be sent to the Base station using the Revolabs HD Firmware Loader The software can be downloaded at www revolabs com downloads Updating the HD Venue Base Station and HD Microphones Connect to the Base Station using the mini USB cable Pair both mics to the Base Station and make sure they are out of the Charger Base Start the Revolabs HD Firmware Loader software Choose the desired firmware version from the location it was saved during download Choose whether you would like to update the Base Station Mics or Both select OK The Revolabs HD Firmware Loader will notify you when complete ot R The HD Microphone firmware updates wirelessly during the firmware process as long as the microphones are out of the Charger Base paired to the Base Station and communicating with the Base Station Revolabs HD Indicator LEDs The following tables show activities associated with the various states shown by the LEDs Equipment Use Microphone LED Base Station Channel LEDs Microphone in Charger Solid RED Charging in Progress Base
7. all red green yellow and the microphone will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to remind the user to return the microphone to the conference room If the microphone is moved back into range within 15 minutes the connection will automatically be re established to its original state and the beeping will cease If not the microphone will turn off Adjusting the Volume on the Wearable Microphone Earpiece To change the volume on the Wearable microphone earpiece use the dial on the earpiece wire LOUDER Microphone i Earpiece End End SOFTER Turning the dial towards the earpiece as shown in the figure will increase the volume and turning the dial towards the microphone will decrease the volume Use the attached clothing clip to secure the earpiece wire Using the HD Omni Directional Tabletop Wireless Boundary Microphones The HD Omni directional Tabletop Wireless Boundary Microphones enable multiple conference attendees to use a single microphone LED display visual status for mute un mute and pairing Mute button press to mute un mute and pair microphone Audio jack accepts a 2 5mm plug Charging port docks to Revolabs HD Charger Bases Rubber feet non slip vibration absorbing pads Acoustic Cover protects delicate microphone element non removable OJA WNI To use the HD Omni Tabletop Microphone 1 Remove the m
8. and separate the parts before returning the Adapter to the Charger Base lf the Adapter is moved too far from the Base Station 65 feet or 20 meters the connection will be dropped LED flashes all colors and the audio will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicate that it is out of range Move the Countryman Adapter closer to the Base Station and the connection will automatically be re established to its original state and the beeping will cease If not the Countryman Adapter will continue beeping until it turns off in about 15 minutes Pairing Wireless Microphones to Base Station Pairing creates a link between the HD Wireless Microphone and the Base Station with a unique electronic serial number When the microphone and Base Station have been previously paired the mic will automatically try to connect to the same Base Station whenever it is lifted from the Charger Base Note Microphones in new systems must be paired to the Base Station with each microphone assigned to a unique channel on the Base Station Remember microphones are always muted flashing RED LED when they are removed from the Charger Base and the Mute button needs to be pressed to make it live flashing GREEN LED A microphone that is not paired will be indicated by a cycling RED GREEN LED pattern A Base Station channel that is not paired to a microphone will not show any activity on the cha
9. arge jacks Proprietary 4 pin charge plugs 2 5mm mono earplug port 16 ohm 5V DC 1 Amp switching power supply varies by country 5V DC 2 Amps switching power supply varies by country 300 91 meters approx actual range depends on RF signal absorption reflection and interference Lithium Polymer Up to 8 hours approx talk time 2 hours approx 128 bit DSAA DECT Standard Authentication Algorithm authentication 64 bit DECT Standard Cipher 1 Earpiece with inline volume control and 1 Lanyard per Wearable Microphone Environmental Requirements Temperature Humidity 40 to 105 F 5 to 40 C operating 20 to 85 SOO Index Adjusting the Volume 10 Base Station 5 Back Panel 5 Front Panel 5 Channel LED indicators 5 Channels 6 Charger Bays 16 Charging the Batteries 16 First time use 16 Recharging 16 Connections 6 Earpiece 6 Full Duplex 6 Indicator LEDs 18 Input Connectors 6 LED indicator 16 MC TDMA TDD 3 Microphone Charging port 9 Earpiece Jack 9 _91 LED Display 9 Mute Button 9 Pocket Clip 9 Microphones 9 Pairing 15 Power Cord Receptacle 16 Power In Receptacle 5 Power Module 16 Safety Information 1 Specifications 20 system Components 3 Base Station 3 Diversity Antennas 3 Microphone Charger Base 3 Time Division Duplex 3 Time Division Multiple Access 3 Warranty 19 Wireless Boundary Microphone 10 12 XLR Microphone Wireless Adapter 13 14 Note Mi
10. ates Pairing Push Buttons For pairing microphones to Base Station Antennae Female XLR and Balanced Combo Input Connectors Female 1 2 Balanced Output Connectors Male XLR Balanced Output Connectors Mini USB Serial Interface firmware updates only Configuration DIP Switches see Section Using the Rear Panel Configuration DIP switches Power In Locking Receptacle 5VDC oe eee To Install the Base Station The Revolabs HD Venue Base Station is designed to be installed into a standard 19 AV rack using the attached rack ears 1 Install the HD Venue System into the rack 2 Plug the power cord into an appropriate outlet 3 Connect the necessary outputs and inputs Revolabs HD Venue Base Station Audio Connections There are two 3 5mm balanced inputs either or XLR and two 3 5mm balanced outputs either or XLR on the back panel of the unit providing access to each channel s audio signal Ys jacks are configured as follows XLR connectors are configured as follows There are two output channels representing a separate channel for each microphone The microphone output connectors need to be attached to the input connectors of an audio mixer The Base Station input connectors also 0 dBu may then be attached to mixer channel outputs Because the system is full duplex the input connections provide the ability to hear program audio using a 2 5mm earpiece attached to the microphone supplied
11. crophone FCC Notice to Users Users are not permitted to make changes or modify the equipment in any way Changes or modifications not expressly approved by Revolabs Inc could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Federal Communications Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits for an uncontrolled environment Professional Installation Recommended This product should be professionally installed Industry Canada Notice to Users Operation is subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference including interference that may cause undesired operation of the device IC 6455A 01HDEXEMIC Revolabs HD Microphone Restricted use with certain medical devices Hearing Aids Some devices may interfere with some hearing aids In the event of such interference you may want to consult with your hearing aid manufacturer to discuss alternatives Other Medical Devices If you use any other personal medical device consult the manufacturer of your device to determine if it is adequately shielded f
12. crophones must be fully charged and paired to the Base Station prior to first use Revolabs HD Venue Wireless Microphone System Manual 01 HDVNUMAN PAP 11 SEPT 2010 Rev 1 1 _99 revo
13. e re established to its original state and the beeping will cease If not the XLR Adapter will continue beeping until it turns off in about 15 minutes Using the HD Wireless Adapter for Countryman Microphone The HD Wireless Adapter for Countryman Microphones shown in the following figure is connects to a Countryman microphones for wireless freedom for broadcasting applications with no bulky equipment such as a belt pack or batteries 1 Audio Out port accepts the 2 5mm plug for the earpiece 2 Charging Port docks to all Revolabs HD Charger Bases 14 3 Mute button press to mute un mute and pair microphone 4 LED display visual status for mute un mute and pairing 5 TA4F connector connects to Countryman microphone cable To use the HD Wireless Adapter for Countryman Microphone 4 Remove the Microphone Adapter from the Charger Base The adapter turns on and mutes automatically when removed from Charger Base flashing RED LED The Microphone Adapter is attached to a Countryman Microphone with the specific cable designed for Revolabs The HD Wireless Adapter for Countryman microphone supplies the necessary phantom power specifically for the Countryman microphone 5 To turn the Adapter off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED then release button Important Always remove the microphone from the Adapter
14. icrophone from the Charger Base to turn on and automatically mute the mic indicated by a flashing RED LED 2 Omni Tabletop microphones can be centered on the table within 2 to 5 feet 0 6 to 1 5m away from people speaking and do not need to be pointing any particular direction because they pick up sound from all directions It is always better to be as close to the person speaking as possible but avoid placing the microphone where it might be blocked by equipment or paperwork Avoid placing microphones too close to an audio or video conference speaker to avoid echoes Make sure that the microphone is always placed lying on its rubber feet atop a flat surface RD SO With the microphone in position on the table un mute the microphone by pressing and releasing the Mute button confirm by a flashing GREEN LED To turn microphone off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED and release button lf the microphones are placed too far from the Base Station 65 feet or 20 meters the connection will be dropped LED flashes all colors and the microphone will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicating it s out of range Move the microphone closer to the Base Station and the connection will automatically be re established to its original state and the beeping will cease If no
15. its rubber feet atop a flat surface Refer to diagram below With the microphone in position un mute the microphone by pressing and releasing the Mute button confirm by a flashing GREEN LED 4 To turn microphone off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED and release button lf the microphones are placed too far from the Base Station 65 feet or 20 meters the connection will be dropped LED flashes all colors and the microphone will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicating it s out of range Move the microphone closer to the Base Station and the connection will automatically be re established to its original state and the beeping will cease If not the microphone will continue beeping until it turns off in about 15 minutes Using the HD XLR Microphone Wireless Adapter The HD Wireless XLR Adapter for Handheld Microphone shown in the following figure connects to a handheld dynamic microphone for wireless freedom during open mic meetings Q amp A sessions classrooms etc Audio Out port accepts the 2 5mm plug for the earpiece Charging Port docks to all Revolaobs HD Charger Bases Mute button press to mute un mute and pair microphone LED display visual status for mute un mute and pairing 5 XLR Female connector balanced audio for dyna
16. mic microphones wira To use the HD Universal Wireless Adapter 1 Remove the Microphone Adapter from the Charger Base The adapter turns on and mutes automatically when removed from Charger Base flashing RED LED The XLR Microphone Adapter is attached to a standard dynamic microphone to convert it from a wired microphone to a wireless microphone see following figure Note The Adapter does not provide phantom power or bias current so it cannot be used with condenser or electret microphones 2 With the microphone attached un mute the Adapter by pressing and releasing the Mute button confirm by a flashing GREEN LED Note If the microphone has an on board mute switch this switch must also be un muted prior to use 3 To turn the Adapter off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED then release button Important Always remove the microphone from the Adapter by pressing the latch switch and separating the parts before returning the Adapter to the Charger Base lf the Adapter is moved too far from the Base Station 65 feet or 20 meters the connection will be dropped LED flashes all colors and the audio will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicate that it is out of range Move the XLR Adapter closer to the Base Station and the connection will automatically b
17. ne Standards to which Conformity is declared RF ETSI EN 301 406 V 1 4 1 03 2001 EMC ETSI EN 301 489 6 v1 2 1 2002 04 WEEE Notification The Waste Electrical and Electronic Equipment WEEE directive 2002 96 EC is intended to promote recycling of electrical and electronic equipment and their components at end of life X 2003 11 EC amp 2002 95 EC RoHS Compliance Directive The products referenced herein are in compliance with the EU directive 2003 11 EC and EU directive 2002 95 EC Introduction Congratulations on your purchase of a Revolabs Wireless Microphone System This system utilizes 1 9 GHz DECT technology and high band width audio from multiple wireless microphones enabling clear reliable un tethered communications in recording audio video conferencing speech recognition VOIP communications sound re enforcement as well as many other environments requiring clear audio capture __ revolabs The Revolabs HD Venue Wireless Microphone System has high definition audio which allows the system to pick up the entire human voice spectrum The HD Venue System combines innovative technology and ergonomic design employing Multi Carrier Time Division Multiple Access and Time Division Duplex MC TDMA TDD radio transmissions both to and from the microphone This technology allows the microphones to co exist with other wireless products such as wireless LANs 802 11b amp g and includes digital encryption technol
18. nnel LED make sure unit is first powered on by observing GREEN backlit front panel display When channels are paired both microphone and channel LEDs will flash RED as microphones are removed from the Charger Base and flash GREEN when un muted Remember that only one microphone can be paired to any single Base Station channel To pair an individual microphone to the Base Station 1 Turn the microphone OFF no LED activity If the microphone is ON press and hold the Mute button for 10 seconds until the LED turns solid RED then release the button to turn the unit off do not release the button when you hear two beeps 15 2 Place the microphone unit into pairing mode by holding the Mute button down for seven seconds The LED will turn solid RED Release the Mute button The microphone is now in pairing mode 3 Within one minute push and hold the button for the desired channel on the Base Station for seven seconds until the LED turns solid red then release The LED for that channel will be solid red until pairing starts as indicated by a quick GREEN flash then switching to flashing RED on both the microphone and the Base Station muted audio Pairing is now complete Revolabs HD Venue Charger Base When microphones are not in use they should be properly inserted into the Revolabs HD Charger Base It is important to ensure that all system microphones are inserted fully in the base so that charging will occur Features of the ba
19. ogy to ensure secure communications System Components Your Revolabs HD Venue System contains the following e Rack mountable HD Venue Base Station e HD Microphone Charger Base e HD Wireless Microphones purchased and boxed separately HD Omni Tabletop and HD XLR Adapter shown in photo above for example only The Base Station houses the processor and one end of the wireless connection It features one set of PCB diversity antennae and offers individual line level or mic level audio in out for each microphone channel This allows for external audio processing such as e Mixing Acoustic echo cancellation AEC Feedback elimination Level control Equalization Noise cancellation The system is designed to optimize audio capture reproduction by providing Consistent audio input from all participants Minimum room noise Mute control Wireless encryption Automatic channel selection Full duplex audio The Charger Base charges the HD Wireless Microphones and stores them when not in use Installing the Revolabs HD Venue Base Station The Revolabs HD Venue Base Station shown below in front and rear panel views manages wireless audio signal processing pairing and muting between the Revolabs microphones and the Base Station Front View Rear View 2 Mi i D o o0 ME aiii i YoY E H A 8 9 Controls and Connections Channel LED indicators Displays microphone mute and pairing st
20. ration DIP Switches off on 12345678 DIP Output Mixing Individual Mixed Output Outputs 3 AURO upo Line Level Mic Level Level Mute Mode Eroa No Mutes utes Not Sharing all Sharing 1 2 5 Sharing Mode frequencies will frequencies will be used be used A B 7 Transmit Off On Off On 8 Power Off Off On On Changes in DIP switch configurations require a power cycle off on to take effect Configuration Settings DIP Switch 1 Output Mixing When DIP Switch 1 is OFF default each HD microphone has its own 3 5mm balanced audio output on the Base Station When DIP Switch 1 is switched on the audio outputs of the two HD microphones are mixed together and sent to both outputs DIP Switch 2 Low Pass Filter When DIP switch 2 is OFF default the microphone provides the full audio bandwidth When DIP switch 3 is ON a LPF is activated reducing the audio bandwidth DIP Switch 3 Audio Output Level When DIP switch 3 is OFF default the microphone outputs provide a line level signal O dBu When DIP switch 3 is ON the microphone outputs provide a mic level signal 40 dBu DIP Switch 4 Mute Mode When DIP switch 4 is OFF default each microphone has its own individual muting capabilities When DIP switch 4 is ON the microphone mute buttons are deactivated resulting in the mics always being active and un muted when not in the Charger Base DIP Switch 5 amp 6 Sharing Mode To use two HD Venue System
21. rom RF energy Your physician may be able to assist you in obtaining this information revo Export Law Assurances This product is controlled under the export regulations of the United States of America and Canada The Governments of the United States of America and Canada may resirict the exportation or re exportation of this product to certain destinations For further information contact the U S Department of Commerce or the Canadian Department of Foreign Affairs and International Trade The use of wireless devices and their accessories may be prohibited or restricted in certain areas Always obey the laws and regulations on the use of these products 01 HDVENU North America UPCS Usage Restriction Due to the UPCS frequencies used this product is licensed for operation only in the United States of America and Canada 03 HDVENUEU European Union Usage Restriction Due to the DECT frequencies used this product is licensed for operation only in the European Union countries European Compliance This equipment has been approved in accordance with Council Directive 1999 5 EC Radio Equipment and telecommunications Equipment CE Model Numbers 03 HDEXEMICEU 11 HD Microphone Wearable 03 HDTBLMICEU OM 11 HD Microphone Tabletop Omni directional 03 HDTBLMICEU DR 11 HD Microphone Tabletop Directional 03 HDXLRMICEU 11 HD XLR Wireless Adapter for Dynamic Handheld Microphone 03 HDCOMANEU 11 HD Wireless Adapter for Countryman Micropho
22. s in the same area both systems must have DIP Switch 5 set to ON One of the HD Venue Systems must have DIP Switch 6 set to ON A frequencies and the other HD Venue System must have DIP Switch 6 set to OFF B frequencies DIP Switch 7 amp 8 Transmit Power The transmit power of the Base Station can be adjusted to help reduce the operational radius of a Revolabs HD Venue System in order to prevent interference from other Revolabs products or from other devices operating in the same frequency Note t is recommended that the lowest functioning Transmit Power be used for each system Revolabs HD Microphones and HD Microphone Adapters Use any of five microphones with your Revolabs HD Venue System e Revolabs HD Wearable Wireless Microphone e Revolabs HD Omni directional Tabletop Wireless Boundary Microphone e Revolabs HD Uni directional Tabletop Wireless Boundary Microphone e Revolabs HD Universal Wireless Adapter for Handheld Microphones e Revolabs HD Wireless Adapter for Countryman Microphones Using the HD Wearable Wireless Microphones The Revolabs HD Wearable Microphones shown in the following figure are paired to the Base Station and can be worn on the user s shirt pocket lapel or on a lanyard They provide high quality full duplex audio between each user and the conferencing or audio system Earpiece jack accepts the 2 5mm plug for the earpiece Charging port docks to Revolabs HD Charger Bases Pocket
23. se are shown in the following figure Wee 1 LED indicator power status indicator 2 Charger Bays charges up to 2 Microphones 3 Power Cord Receptacle power supply input 9 24VDC on rear Power Module The Charger Base requires 5VDC power provided by the AC Adapter Plug the supplied AC adapter into an appropriate power outlet 110 240 AC 50 60Hz The power LED on the Charger Base will illuminate Charging the Microphone Batteries First time use Before using the wireless microphone the first time charge the batteries in the microphones for eight hours or overnight in the Charger Base Recharging When the YELLOW LED starts to flash intermittently on the microphone the battery has 30 minutes of charge remaining Over time years batteries gradually wear down and will result in shorter run times This is normal Always return microphones to the Charger Base when not in use Important The Lithium Polymer rechargeable batteries that power the microphones are not user serviceable Please contact Revolabs www revolabs com or your AV service provider for replacement instructions and to assure the proper disposal method is used Warning Never dispose of batteries in a fire because they may explode 16 Either a solid RED LED charging or solid GREEN LED 100 charged will appear to confirm that the microphone is inserted properly in the Charger Base The microphones are not transmitting audio to the HD Base
24. t the microphone will continue beeping until it turns off in about 15 minutes Using the HD Directional Tabletop Wireless Boundary Microphones The HD Tabletop Wireless Microphone shown below is designed to provide optimum coverage when placed on a conference room table in front of one or two people Pickup patter LED display visual status for mute un mute and pairing Rubber feet non slip vibration absorbing pads Audio jack accepts a 2 5mm plug Charging port docks to Revolabs HD Charger Bases Mute button press to mute un mute and pair microphone Acoustic Cover protects microphone element non removable oS a a To use the HD Directional Tabletop Microphone 1 Remove the microphone from the Charger Base to turn on and automatically mute the mic indicated by a flashing RED LED Directional Tabletop microphones should be located on the table with the acoustic cover pointed toward the users trying to keep the microphone 2 to 5 feet 0 6 to 1 5m from the target person or two The pick up pattern for this directional microphone is 45 to either side of directly in front of the microphone It is always better to be as close to the person speaking as possible but avoid placing the microphone where it might be blocked by equipment or paperwork Avoid placing microphones too close to an audio or video conference speaker to avoid echoes Make sure that the microphone is always placed lying on
25. with the wearable microphone Depending on the application it is possible to feed a single audio feed back to each earpiece This would allow for translation personal hearing assistance or other services to be incorporated into an application NOTE The USB port may exhibit static sensitivity If the Base Station audio shuts down after handling please power cycle the Base Station Note The HD Venue System is not compatible with any other Revolabs system and therefore cannot be installed in the same room The HD and Solo Wireless Microphones and Charger Bases are not interchangeable Only two HD Venue Systems can be used in a single area Please contact support revolabs com for design recommendations Configuring the Revolabs HD Venue Base Station Each Revolabs HD Venue Base Station must be configured properly prior to use Accurate configuration is dependent on several variables such as e Is Line Level or Mic Level signal required Refer to setting Dip Switch 3 below e How many HD Venue Systems are being used together in close proximity lf you have more than one Revolabs HD Venue Wireless Microphone System refer to setting Dip Switches 5 and 6 below Note t is recommended that the lowest functioning Transmit Power be used for each system e How large is the room Refer to setting Dip Switches 7 and 8 below Note t is recommended that the lowest functioning Transmit Power be used for each system Using the Rear Panel Configu
Download Pdf Manuals
Related Search