RCA RLED4664A Flat Panel Television User Manual
Contents
1. OPERATING INSTRUCTIONS 46 1080p LED Television RLED4664A Contents Contents Caution Safety Information Unit and Accessories Product Feature Introduction 1 Front View 2 Rear View 3 Instruction for Wall Mount 4 Remote Control Basic Operation OSD Menu 1 Picture menu 2 Sound menu 3 Channel menu A Parental Control menu 5 Setup menu 6 Others menu Simple Troubleshooting Technical Specifications Caution The lightening flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the persons The exclamation point within an equilateral triangle is intend to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Waste Electrical amp Electronic Equipment WEEE Your product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre Inthe USA there are separate collection systems for used electrical and E Correct disposal of this Product P2. VIDEO Ww 9 gt a Ww 7 x lt Q 8 HDMI3 HDMI2 1 AC POWER IN Connect to an earth 100 240V 50 60Hz outlet with the power cable 2 Headphone out Connect it to your headphone or audio equipments 3 PC IN Connect it to the audio output of PC 4 RF Connect antenna or cable 75 Ohm coaxial to receive TV signal 9 VGA For PC display Connect it to the D Sub 15 pins analog output of the PC 6 HDMI1 2 3 Connect it to the HDMI output of video device 7 COAX Digital audio output 8 Service For service use only 9 VIDEO Connect it to video output of video device L R in Connect them to audio output of video device shared with YPbPr 10 YPbPr Connect them to the component video output of video device 11 L R out Connect them to audio equipments Introduction 3 Instruction for Wall Mount A wall mount kit purchased separately would allow you to mount your RCA TV on the wall For detailed information on installing the wall mount refer to the instructions provided by the wall mount manufacturer It is strongly recommended to contact a technician for professional assistance for wall mount installation RCA is not responsible for any damage to the product or injury to yourself or others resulting from the wall mounting Dimensions for Mounting Hole Pattern This RCA TV is compatible with a 400mm x 400mm mounting hole pattern 4 pcs oftype MB6 screws are required for installing
3. Channel Search Press OK button to start auto channel search AUTO CHANNEL SEARCH Cabl Now Searching Please Wait AP x If you select Cable as input signal in Antenna item you can press gt button to search the channels automatically A The receivable channels will be stored automatically Digital Channels Found O When searching channels press MENU to stop Stop Auto Channel Search 7 Skip AUTO CHANNEL SEARCH Air Now Searching Please Wait a If you select Air as input signal in Antenna item you can press gt button to search the channels automatically Analog Channels Found 0 The receivable channels will be stored automatically Digital Channels Found O When searching channels press MENU to stop NOTE It will take a while to auto scan in NTSC or ATSC mode please wait patiently 573 Stop Auto Channel Search Skip 14 OSD Menu OSD Menu 4 Parental Control menu You must enter the password to gain access to the Parental Control menu The default password is 0000 You may modify the following options mg PARENTA 1 E m Lock Parental Control Description V CHIP Press gt button to enter the V CHIP menu Fa CHIP US V CHIP Press gt button to enter the US V CHIP menu Movie Rating The Movie rating MPAA is used for original movies rated by the Motion Picture Association erating of America MPAA as broadcasted on cable TV and TV Ratin
4. EPEE pP D electronic products Please help us to conserve the environment we live in C gl u This unit complies with America Safety directives Intertek 31 24140 CONFORMS TO UL STD 60065 CERTIFIED TO CSA STD C22 2 N0 60065 This unit complies with FCC directives Safety Information Safety Information To ensure reliable and safe operation of this equipment please read carefully all the instructions in this user guide especially the safety information below Electrical safety e To prevent overload don t share the same mains supply socket with too many other items of equipment Do not place any connecting wires where they may be stepped on or tripped over Do not place heavy items on the leads which may damage them Hold the Mains plug not the wires when removing from a socket During a thunderstorm or while leaving the TV for long periods disconnect the aerial if outdoor and the power cable from the supply Do not allow water or moisture to enter the TV Do NOT use in wet or moist areas such as Bathrooms steamy kitchens or near swimming pools Pull the plug out immediately and seek professional help if the mains plug or cable is damaged liquid is spilt onto the set or if it is accidentally exposed to water or moisture anything accidentally penetrates the ventilation slots the set does not work normally Do NOT remove the safety covers There are no user serviceable parts inside You may invalidat
5. e Reset Press OK button to reset the settings Clock Color Temp Select between Normal Cool and Warm 11 OSD Menu OSD Menu Advanced Picture Settings Press gt button to enter the Advanced Picture Settings ADVANCED PICTURE SETTINGS Dynamic Contrast Select the dynamic contrast mode Dynamic Contrast Mediu between Off Low Medium and High Film Mode Film Mode Activate or deactivate the Film Mode Nose Re Noise Reduction If the broadcast signal received is MPEG Notse DEREN weak you can select the DNR option to reduce the video noise level between Off Low Medium and High MPEG Noise Reduction Select the MPEG Noise Reduction option to reduce the picture noise level Return Move AP Change Setting between Off Low Medium and High 12 OSD Menu OSD Menu 2 Sound menu SOUND Surround Mode AVL Analog Sound Digital Sound Digital Audio Output Equalizer Settings Description Sound Settings Press gt button to enter the Sound Settings menu A Sound Mode Select your desired picture mode as follow Dynamic Standard Soft and User You may select the sound mode directly by pressing a the SOUND button on the remote control les Bass Low frequency intensity Treble High frequency intensity Balance Left and right stereo audio channels balance SA E O E ESE SES S Retum Move MP Change Setting Surround Mode Activate or deacti
6. e the TV set Y SOURCE LOCK AV YPbPr Source Lock Invalidate the source input you select HDMI 1 HOMI HOMI 3 16 OSD Menu OSD Menu 5 Setup menu Menu Pe Clock Description Closed Caption Press gt button to enter the Closed Caption menu 2 lt CLOSED CAP wm Caption Display Activate or deactivate the Caption displaying Analog Caption Type Allow you to select the basic selection among CC1 CC2 CC3 CC4 Text1 Text2 Text3 and Text4 Digital Caption Type Allow you to select the advanced selection among Service1 Service2 Service3 Service4 Service 5 and Service 6 Digital CC Preset Select the Digital CC Preset between ER Default and Custom daa a Digital CC Style Setting the Digital CC Style CLOSED CAPTION _ o menu Return z Move Menu Language Select OSD menu language LOCH Press gt button to enter the Clock menu de 5 Time zone Select the time zone for the TV Auto Clock Activate or deactivate the Auto Clock function gt es a 2005 01 01 12 26 55 Day of Week Sat j yi Setup Time Display the setup time of the TV mi see E Day of Week Display the day of week Daylight Saving Time Activate or deactivate the ine ee Daylight Saving Time function for the TV 17 OSD Menu OSD Menu 6 Others menu OTHERS Blue Back No Signal Power Off No Operation Power Off All Reset 0 Return Move xr On Off Desc
7. e the warranty Qualified personnel only are permitted to service this apparatus To avoid battery leakage remove exhausted batteries from the remote control handset or when not using for along period Do NOT break open or throw exhausted batteries on a fire Physical safety e Do NOT block ventilation slots in the back cover You may place the TV in a cabinet but ensure at least 5cm 2 clearance all around the unit e Do NOT tap or shake the TV screen you may damage the internal circuitry Take good care of the remote control do not drop it or allow it to come into contact with liquids e To clean the TV use a soft dry cloth Do NOT use solvents or petrol based fluids For stubborn stains you may use a damp soft cloth with diluted detergent Unit and Accessories and Product Feature Unit and Accessories TV set Instructions for fixing TV stand Note the pictures below are only for reference The parts Installation There are four parts for installing stand 1 Put Ka neck on the stand rear 2 Put the stand rear board on the rear ix the if User s Manual oe stand base Screws three specifications 1 screws B4 16 picturel ces M4 12 pictures2 mat pieces M4 Stand Installation Guide User s Manual Remote Control and Batteries AAA x2 Product Feature e 46 measured diagonally wide screen for a complete home theater experience e 1920 x 1080 native resolution for Full HD 1080p perfo
8. f the TV Press POWER button on the TV or remote control TV Source Select Input Source select AV Press INPUT button on the TV set or remote control to display input YPbP source menu and use CH button on the TV set or A V button aa on remote control to select the input source press OK button on the remote control to enter Note Before you select the input source make sure the HDMI 3 connections are prepared E HDMI 2 Basic OSD Menu operation Press MENU button to display the OSD menu as below Main menu Picture IL e f K gt Sound K 5 Use lt gt button to select Channel SOUND CHANNEL PARENTAI SETUP OTHERS Parental Setup Others Press OK button K PICTURE i s Screen Size Submenu PC Settings Picture menu Color Temperature for example Advanced Picture Settings a Return Move EYF Go to Next Menu l Guide This guide shows the keys buttons on the remote control for selecting the items to setup in the OSD menu Use lt gt button to select the main menu and press OK button to enter the submenu In the submenu use V button to select the function item press lt gt button to adjust setup or press gt button to enter the submenu Press MENU button to return to the upper menu Press EXIT button to exit the menu display 10 OSD Menu OSD Menu 1 Picture menu K PICTURE Screen Size PC Settings Color Temperature Normal Advanced Picture Settings C Retur
9. g not edited for television Use A V button to select G PG PG 13 R NC 17 or X G General Audiences Movie is appropriate for all ages 1 jee PG Parental Guideance Suggested May contain material not suited for younger viewers PG 13 Contains content that may not be appropriate for viewers under the age of 13 R Restricted Contains adult content no one under 17 admitted r without parent NC 17 No one 17 and under admintted X Adults only J LI LILI Prrrr TV Rating Use A V buttons to select the desired FE FEP rating and press gt button to block or unblock rating 15 OSD Menu OSD Menu Canada V CHIP Press gt button to enter the Canada Tr V CHIP menu English Rating Select among C C8 G PG French Rating 14 and 18 French Rating Select among G 8ans 13ans 16ans and 18anst Retum Move Block UnRated Show Activate or deactivate the Block UnRated Show function Downloadable Rating Setting the Downloadable Rating in DIV mode when the program has the rating information Clear Downloadable Data Clear the downloadable data of the TV Note The two operations above only valid when playing the downloadable data stream a CHANGE PASSWORD Old PIN Change password Change the password you must enter the new password twice to confirm it Note Do not forget the password Contr w Retum 0 9 Enter password Keypad Lock Invalidate the buttons on
10. n Move Go to Next Menu Description Picture Settings Press gt button to enter the Picture Settings menu Picture mode Select between Dynamic Standard Movie User and Power Saving You may select the picture mode directly by pressing the PICTURE button on the remote control Brightness Note when select the Power Saving the ect alr machine is in energy saving status A Brightness Adjust brightness of the picture Contrast Control the difference between the bright and dark regions of the screen picture Color Adjust color of the picture C Retum amp Move 98 Change Setting a Tint Control the fresh tones to make them appear natural Sharpness Set the amount of fine detail in the picture Screen Size Select the displaying mode of the picture between Wide Cinema Zoom Normal Just Scan PC Settings If the video input signal comes from your PC you may adjust the Vertical Position Horizontal Position Clock Phase or even perform an Auto adjustment Tint Sharpness Auto Adjust Press OK button to setup the parameter of the screen automatically Horizonte Eon Clock Adjust the pixel clock frequency until the image Vertical Position size is maximized for the screen H V Position Adjust the transverse vertical position of the screen Phase Adjust the phase of the ADC sampling clock relative to the sync signal until a stable image is obtained Retum 9 Move 9 press to Execut
11. odes SOUND Press to cycle through the different sound settings SLEEP Shutdown timer DISPLAY Display the information of current mode VOL Press to adjust the volume CH Press to scan through channels MUTE Press to mute the sound press again or press VOL to unmute MENU Press to display the OSD menu EXIT Press to exit the OSD menu Thumbstick lt gt v A Allows you to navigate the on screen menus and adjust the system settings to your preference OK CONFIRM button CC Press to display the closed caption MTS Press to select the audio channels EPG Press to enter the EPG menu directly FAV Press to add or remove favorite channel Universal Remote Control not included Introduction Installing Batteries 1 Open the battery compartment cover on the back of the remote control 2 Insert two 1 5V AAA size batteries observing the polarity markings inside the battery compartment Don t mix different types or used batteries with new ones 3 Close the cover AN Batteries shall not be exposed to excessive heat such as sunshine or fire The remote control should be operated within 23 feet 7m and 30 to the left and right of the IR Receiver on the front of the TV Used batteries should be disposed properly Basic Operation Basic Operation Power on off 1 Connect to the power supply with the power cord 2 To turn on the TV Press POWER button on the TV or remote control To turn of
12. ration Check if the batteries in the remote control is weak or exhausted This TV is for household use and registered as harmless on electromagnetic waves 19 Technical Specifications Technical Specifications Model Description 46 LED TV Panel Type LED Panel Pane 16 7M 60Hz ATSC NTSC en M 75 ohm external terminal Video 480i 480p 720p 1080i 1080p Audio Two channel linear PCM 32 44 1 and 48kHz 16 20 and 24 bits D sub 15pin G 0 7Vp p 750hms PC RGB Input B 0 7Vp p 750hms R 0 7Vp p 7 5ohms Composite Video Input 1 0 Vp p 75ohms Y 1 0 Vp p 75ohms 0 3V negative sync Component Y Pb Pr Input Pb 0 7Vp p 750hms Pr 0 7Vp p 750ohms Component AUDIO For Component Audio input AV AUDIO For CVBS Audio input Sound Input PC AUDIO For PC RGB Audio input 500mV rms Impedance 20k ohms Power Requirement 100 240V 50 60Hz Power Consumption 150W Product specifications and appearance are subject to change without notice Hom HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries 20
13. ription Blue Back Turn on off the blue screen function when there s no signal No Signal Power Off The TV will turn off automatically if there s no signal after 10 minutes No Operation Power Off The TV will turn off automatically if there s no operation on the TV after 3 hours All Reset Reset all the settings 18 S imple Troubleshooting Simple Troubleshooting If the TV has failed or its performance has seriously deteriorated check the TV by using the following simple troubleshooting guide lf you can not resolve the problem with this troubleshooting please call Technical Support No power Check all power connections to the TV Press either the power button or the Standby button on the Remote control No picture or sound Ensure that the TV is plugged in and the power is on Ensure that the antenna is connected Try a different program Poor picture quality Check the antenna connections Check if the channel is tuned in properly Adjust the picture settings brightness color sharpness contrast or hue Make sure that the TV is not located close to electrical appliances that may emit radio frequency interference No color Adjust the color setting Check if the program is color Check if the cannel is tuned properly TV does not respond to remote control Check if no obstruction is between the remote control and the unit Check if the remote control is within the range of ope
14. rmance e Integrated ATSC TV tuner for HDTV broadcast reception e Three HDMI inputs for true digital connections e VGA port for connection to PC HDMI is a trademark of HDMI Licensing LLC in the United States and other countries Introduction Introduction 1 Front View Power Indicator Remote Control window Keep clear 1 IR Infrared Receiver Receives IR signals from the remote control Power on Standby LED Indicator Press POWER to turn on and off Indicator on Red Standby mode Indicator on Green Power on mode The effective receiving range for the signal is 5 8 metres from the front of the remote control window and 30 to the left or right side and 20 above or below the remote control window Source Select 2 The functions of the buttons INPUT Press to display the input source menu MENU Press to display the OSD menu press again to exit the menu YPbP CH Press to scan through channels E VOL Press to adjust the volume POWER Turn on standby the TV set HDMI 2 HDMI 3 PC Press INPUT button on the TV set or remote control to display the input source menu and use CH button on the TV set or A V button on remote control to select the input source press OK button on the remote control to enter Note Before you select the input source make sure the connections are prepared Introduction 2 Rear View SN j 4 AN N Do
15. the wall mount bracket to your RCA TV Do not use screws that are longer than 12 mm Screws that are too long may cause damage to the inside of the TV set Do not fasten the screws too tight for this may damage the TV or cause the TV to fall resulting in personal injury RCA is not liable for these kinds of incidents Do not mount your RCA TV at more than a 15 degree tilt Always use two people to mount the TV to a wall Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock 4 Remote Control Introduction The remote control is using Infra Red IR Point it towards the front of the TV The remote control may not work correctly if it is operated out of range or out of angle l l Es PICTURE SOUND SLEEP DISPLAY Universal Remote Code 11359 1 POWER red button Turn the TV on standby INPUT Press to display the input source menu Number Buttons Choose channel directly Select channel 5 Press button 5 Select channel 62 Press button 6 then press button 2 in 2 seconds Select channel 151 Press button 1 and press button 5 in 2 seconds and press button 1 in 2 seconds Select channel 5 1 Press button 5 and press button in 2 seconds and press button 1 in 2 seconds CZD RETURN Return to the previous channel viewed PICTURE Press repeatedly to cycle through the available video picture m
16. vate the Surround function AVL Activate or deactivate the Auto Volume Limited function Analog Sound Select the Analog Sound mode between Stereo Mono and SAP Digital Sound Select the Digital Sound laguage Digital Audio Output Select the Digital Audio Output mode between PCM RAW and off Equalizer Settings Press gt button to enter the Equalizer Settings menu nn m EQUALIZER SETTINGS Use lt gt button to select the mode between User Off Rock Pop and Jazz You could press V button to enter the bottom item to adjust the equalizer bu yourself when you select the User mode Use lt gt button to select the item and use V button to adjust You could come back to the Mode selecting SS e e En rrr e HE A Y A A SS EEE EEE SS Y Er e Retum 9 Move AP Change Setting item by pressing lt button 13 OSD Menu OSD Menu 3 Channel menu CHANNEL Ban Favorite List Channel Settings Signal Type Auto Channel Search a Description Channel List Display the channel list Favorite List Display the favorite channel list Channel Settings Press gt button to display the Channel Settings menu CHANNEL SETTINGS Page 1 1 Channel Skip Favonte Label AISC 1 ATSC 3 Press lt gt AV button to select the item and press OK button Unnamed to change the setting sae ses eee E mm E E E O mm mE E AAA ee ee mE Signal Type Allow you to select antenna between Air and Cable Auto
Download Pdf Manuals
Related Search