Pioneer AVH-P6000DVD Stereo Receiver User Manual
Contents
1. When connecting this product to another product refer to the supplied Installation manuals of both products and con nect cords that have the same function m Z A T Connecting the Units Connecting the power cord 1 e Refer to page 8 This product IP BUS input 7 Blue Multi CD player sold separately AV BUS input IP BUS cable Lightgreen Z lt Violet white Refer to page 5 TR E Fuse resistor Yellow black If you use a cellular telephone connect it via the Audio Mute lead on the cellular telephone If not keep the Audio Mute lead free of any connections ll Fuse holder g D Yellow To terminal always supplied with power regardless of ignition switch position a a em Red Fuse resistor To electric terminal controlled by ignition switch 12 V DC ON OFF 111 Orange white Fuse resistor To lighting switch terminal Black ground To vehicle metal body With a 2 speaker system do not connect anything to the speaker leads that are not connected to speakers Blue white To system control terminal of the power amp or Auto antenna a relay control terminal max 300 mA 12V DC Front speaker Front speaker Left Rear speaker Rear speaker Subwoofer Subwoofer output or non fading output SUBWOOFER OUTPUT or NON FADING OUTPUT ani cs D Rear output REAR OUTPUT cs D ce D2. unit to the vehicle battery Engine vibration may eventually cause the insu lation to fail at the point where the wire passes from the passenger compartment into the engine compartment Take extra care in securing the wire at this point e It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift Be sure to install the display in such a way that it will not obstruct driving Make sure that wires will not interfere with moving parts of the vehicle such as the gearshift parking brake or seat slid ing mechanism Do not shorten any leads If you do the protection circuit may fail to work properly Note This unit is for vehicles with a 12 volt battery and negative grounding Before installing it in a recre ational vehicle truck or bus check the battery voltage To avoid shorts in the electrical system be sure to disconnect the battery cable before beginning installation Refer to the owner s manual for details on connecting the power amp and other units then make connections correctly Secure the wiring with cable clamps or adhesive tape To protect the wiring wrap adhesive tape around them where they lie against metal parts Route and secure all wiring so it cannot touch any moving parts such as the gear shift handbrake and seat rails Do not route wiring in places that get hot such as near the heater outlet If the insu lation of the wiring melts or ge
3. Front output FRONT OUTPUT ch E Connecting cords with RCA pin plugs sold separately jm afe gt Power amp a 7 fas sold separately lt E Power amp sold separately Power amp sold separately Front speaker White black Green Green black Gray black Violet black Mos Front speaker O Right Ed Rear speaker O Violet Rear speaker Subwoofer Perform these connections when using a different amp sold separately Connecting the Units Connecting the power cord 2 When using this product with a back up camera automatic switching to VIDEO video when the gear shift is moved to the REVERSE R position is possible Connect the back up camera to the VIDEO input Se pm re product Note When you have completed lead wire connection perform VIDEO SETTING correctly while referring to the Operation Manual It is necessary to set to BACK UP CAMERA in the VIDEO SETTING when connecting the back up camera Power cable Fuse resistor Violet white Of the two lead wires connected to the back lamp connect the one in which the voltage changes when the gear shift is in the REVERSE R position This connection enables the unit to sense whether the car is moving forwards or backwards Light green Used to detect the ON OFF status of the parking brake This lead must be connect
4. Pioneer sound vision soul 1 est lt e AVH P6450CD AVH P6450 This product conforms to new cord colors Los colores de los cables de este producto se confor man con un nuevo c digo de colores As cores dos fios deste produto seguem um novo padr o de cores ZAR EE RATER RER gt BASS dE AA ASAS E ga SANT oll go SEH Lis pora gt a m Z a E Y m oz ag gt Z E y I 3 4 Q m nN E Contents Connecting the Units Connecting the Units in 1 Connecting the power cord 1 ococicicicicacicinanass 3 A CAUTION Connecting the power cord 2 neeese 5 Connecting the system A mn 6 PIONEER does not recommend that Connecting the system B s scesseseseeeeeeeeeees 7 you install or service your display your VIDEO Input Output Connection 8 self Installing or servicing the product may expose you to risk of electric shock Installation or other hazards Refer all installation DIN Front Rear mount and servicing of your display to autho DIN Front mount ses rized Pioneer service personnel DIN Rear Mou 1 sessessssesseszerpscccsvescevmsscosyesacerse Secure all wiring with cable clamps or electrical tape Do not allow any bare wiring to remain exposed Do not drill a hole into the engine com partment to connect the yellow lead of the
5. a booster power supply terminal When an external power amp is being used with this system be sure not to connect the blue white lead to the amp s power terminal Likewise do not connect the blue white lead to the power ter minal of the auto antenna Such connection could cause excessive current drain and malfunction To avoid short circuiting cover the disconnected lead with insulating tape Especially insulate the nused speaker leads without fail There is a possi bility of short circuiting if the leads are not insu lated To prevent incorrect connection the input side of the IP BUS connector is blue and the output side is black Connect the connectors of the same col ors correctly If this unit is installed in a vehicle that does not have an ACC accessory position on the ignition switch the red lead of the unit should be connect ed to a terminal coupled with ignition switch ON OFF operations If this is not done the vehi cle battery may be drained when you are away from the vehicle for several hours Fig 1 ACC position No ACC position Fig 1 The black lead is ground Please ground this lead separately from the ground of high current prod ucts such as power amps If you ground the products together and the ground becomes detached there is a risk of dam age to the products or fire Cords for this product and those for other prod ucts may be different colors even if they have the same function
6. ces on each side Use any of binding screws 4 x 3 mm binding screws 5 x 6 mm or flush surface screws 5 x 6 mm depending on the shape of the screw holes in the bracket 1 Use binding screws 4 x 3 mm only m Z 2 E Ca T Fig 13 Factory radio mounting bracket Fig 14 PIONEER CORPORATION 4 1 MEGURO 1 CHOME MEGURO KU TOKYO 153 8654 JAPAN PIONEER ELECTRONICS USA INC P O Box 1540 Long Beach California 90801 1540 U S A TEL 800 421 1404 PIONEER EUROPE NV Haven 1087 Keetberglaan 1 B 9120 Melsele Belgium TEL 0 3 570 05 11 PIONEER ELECTRONICS ASIACENTRE PTE LTD 253 Alexandra Road 04 01 Singapore 159936 TEL 65 6472 1111 PIONEER ELECTRONICS AUSTRALIA PTY LTD 178 184 Boundary Road Braeside Victoria 3195 Australia TEL 03 9586 6300 PIONEER ELECTRONICS OF CANADA INC 300 Allstate Parkway Markham Ontario L3R OP2 Canada TEL 905 479 4411 PIONEER ELECTRONICS DE MEXICO S A de C V San Lorenzo 1009 3er Piso Desp 302 Col Del Valle Mexico D F C P 03100 TEL 55 5688 52 90 F ES BIRD Bl RS Rd PLAK 4401388 Q gt PRINTED WITH SOY INK BRR 02 2521 3588 Published by Pioneer Corporation Copyright 2002 by Pioneer Corporation HEF FEI ERAR All rights reserved SS SRS ESO od Publication de Pioneer Corporation 17881704 062E Copyright O 2002 Pioneer Corporation Eih 0852 2848 6488 lt KFJFF 02C00000 gt Tous droits de
7. e sensor This Product supplied with Multi DVD player O AA HS l STAND IP BUS ALONE Multi DVD player sold separately lt e g XDV P9 gt Yellow VIDEO 0 Blue INPUT or BACK UP CAMERA A Black AV BUS cable supplied with the TV tuner IP BUS cable supplied with the TV tuner IP BUS cable supplied with Multi DVD player A Yellow FRONT VIDEO OUTPUT ETEL a Hide away TV Tuner sold separately lt e g GEX P6450T VP Multi CD player sold separately RCA cable supplied with Multi DVD player Zz Perform VIDEO SETTING correctly while referring to the Operation Manual Fig 5 VIDEO Input Output Connection Commercially available portable video component with RCA output or back up camera y This product Le Yellow video input 23 cm VIDEO INPUT or BACK UP CAMERA ES White Red audio input L R To audio outputs RCA cable sold separately AUDIO INPUT Display with 3 RCA input jacks To video input 7 lt 2 lt gt 15 cm Yellow rear display output RCA cable REAR MONITOR OUTPUT sold separately Perform VIDEO SETTING correctly while referring to the Operation Manual Fig 6 Installation Note Before finally installing the unit connect the wiring temporarily making sure it is all connect ed up properly and the unit and the system work prope
8. ed to the power supply side of the parking brake switch Parking brake switch Power supply side Ground side Note The position of the parking brake Clamp the parking Clamp firmly with switch depends on the vehicle model brake switch power needle nosed For details consult the vehicle supply side lead pliers Owner s Manual or dealer q 5 Fig 3 Connecting the system A This product Blue N IP BUS cable supplied with TV tuner ES 7 AV BUS cable supplied with TV tuner DVD player sold separately lt e g SDV P7 gt 7 0000 pa MN A IP BUS cable Blue AV BUS cable Blue AV BUS Tr e x cable 1 Hide away TV Tuner Not used sold separately lt e g GEX P6450TVP gt AS i V BUS cable AV BUS Input j i sold separately Blue O O O lt CD AB301E gt N IP BUS cable Multi CD player sold separately Black AV BUS cable supplied with TV tuner Blue AV BUS cable dre rt dd DU RI en O rei SR OTTER supplied with TV tuner Black When a DVD player e g SDV P7 is not used use the AV BUS cable supplied with TV tuner i instead of the AV BUS cable lt CD AB301E gt O ro room J sold separately 1 in the figure Perform VIDEO SETTING correctly while referring to the Operation Manual Fig 4 Connecting the Units Connecting the system B Remot
9. ing the unit Fig 10 As a rule secure with side brackets large Holder After inserting the holder into the dash board then select the appropriate tabs according to the thickness of the dash board material and bend them Install as firmly as possible using the top and bottom tabs To secure bend the tabs 90 degrees AS gt Side bracket E SARA large Fig 10 Installation m When the installation space is not very deep When installing in a shallow space secure with side brackets small In this case stick conceal tape on parts that protrude from the dashboard Holder After inserting the holder into the dash board then select the appropriate tabs according to the thickness of the dash board material and bend them Install as firmly as possible using the top and bottom tabs To secure bend the tabs 90 degrees a Conceal tape Attach screw Ss D AI Side bracket a D small Fig 11 DIN Rear mount Installation using the screw holes on the side of the unit 1 Remove the frame Fig 12 Frame SZA Pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it Fig 12 2 Fastening the unit to the factory radio mounting bracket Fig 13 Fig 14 Select a position where the screw holes of the bracket and the screw holes of this product become aligned are fitted and tighten the screws at 2 pla
10. reproduction et de traduction r serv s Printed in Japan Imprim au Japon lt CRD3656 A gt ES
11. rly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifica tions of the vehicle Install the unit where it does not get in the dri ver s way and cannot injure the passenger if there is a sudden stop like an emergency stop Do not place the display in a position where it will impede the driver s visibility or affect the operation of your vehicle s air bags The semiconductor laser will be damaged if it overheats so don t install the unit anywhere hot for instance near a heater outlet DIN Front Rear mount If installation angle exceeds 30 from horizontal the unit might not give its optimum performance Fig 7 30 Fig 7 This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of unit chassis For details refer to the following illustrated installation methods DIN Front mount Installation with the rubber bush 1 Remove the frame Fig 8 Frame mS Pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it Fig 8 2 Install side brackets Fig 9 m Z E A T Flush surface screw 5 x 6 mm Fig 9 3 Fasten
12. ts torn there is a danger of the wiring short circuiting to the vehicle body Don t pass the yellow lead through a hole into the engine compartment to connect to the battery This will damage the lead insulation and cause a very dangerous short Do not shorten any leads If you do the protection circuit may fail to work when it should Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead The current capacity of the lead will be exceeded causing overheating When replacing fuse be sure to use only fuse of the rating prescribed on the fuse holder Since a unique BPTL circuit is employed never wire so the speaker leads are directly grounded or the left and right speaker leads are common If the RCA pin jack on the unit will not be used do not remove the caps attached to the end of the connector Speakers connected to this unit must be high power types with minimum rating of 50 W and impedance of 4 to 8 ohms Connecting speakers with output and or impedance values other than those noted here may result in the speakers catch ing fire emitting smoke or becoming damaged When this product s source is switched ON a control signal is output through the blue white lead Connect to an external power amp s system remote control or the car s Auto antenna relay control terminal max 300 mA 12 V DC If the car features a glass antenna connect to the anten n
Download Pdf Manuals
Related Search