Pelco C2946M Digital Camera User Manual
Contents
1. C2947M E 6 09 C10CH Series Camera Quick Start Guide This quick start guide describes how to install and configure the C10CH Series camera in most applications It contains a representation of the setup menus to help you locate and change specific settings Refer to the enclosed CD for the following documentation e _Installation Operation manual C2946M e Quick Start Guide C2947M e _ mportant Safety Instructions SAFETY PDF MODELS C10CH 6 1 3 inch ultra high resolution color CCD camera 24 VAC or 12 VDC NTSC format C1OCH 6X 1 3 inch ultra high resolution color CCD camera 24 VAC or 12 VDC PAL format C1OCH 7X 1 3 inch ultra high resolution color CCD camera 220 to 240 VAC PAL format C10CH 7X BACK Camera Mount Ground Screw Back Focus Locking Screw Power Connector Lens Mount e C10CH 6 6X Power Terminal Block e C10CH 7X Power Cord Auto Iris Lens Connector Video Output Connector Setup Button SETUP MENUS The camera default settings are set at the factory to operate in most applications and lighting conditions and normally require no adjustments Sometimes however adjustments may be necessary Use the setup menus to customize the camera settings for your application as needed Refer to the Installation Operation manual C2946M for complete instructions and explanations of camera settings PROFILES STANDARD GAMING CUSTOM MAIN MENU BACK EXIT PROFI2. LES EXPOSURE SET FUNCTION SET SAVE AS CUSTOM SYSTEM INFORMATION EXPOSURE SET ECLIPSER AUTO EXPOSURE ECLIPSER ECLIPSER THRESHOLD DC IRIS LEVEL gt LEVEL FLICKERLESS AGC BACK EXIT BACK EXIT FUNCTION SET LINE SYNC LINE SYNC gt AUTO LINE SYNC WHITE BALANCE gt AUTO V PHASE ADJ CHROMA gt GAMMA gt 60 BACK EXIT SHARPNESS gt SHARP CABLE COMPENSATION gt SHORT MASKING gt TITLE gt BACK EXIT MASKING MASK MASK COLOR MASK EDIT MASK ERASE SAVE AS CUSTOM BACK EXIT CURRENT SETTING ARE SAVED OK CANCEL TITLE TITLE PIXEL CORRECTION ANS BACK EXIT COVER THE LENS AND PRESS OK OK CANCEL SYSTEM INFORMATION RESTORE FACTORY SETTING FIRMWARE VERSION ALL SETTING ARE OSD VERSION INITIALIZED RESTORE FACTORY SETTINGS gt OK CANCEL RETURN END ACCESSING THE SETUP MENUS Use the 5 position button controller on the side panel of the camera to access and navigate the on screen display OSD menus Use the following table to navigate through the menu options Menu Options Navigating the Menu Display the MAIN MENU on the screen Press and hold down the center button for two seconds Move the cursor up or down in a menu or toggle Move the button up or down through menu selections Move the cursor right or left in a menu Move the button left or right Select a menu or make a menu selection Press the center button Save a setting and then return to
3. ia 93612 USA www pelco com USA amp Canada e Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 C2947M E 6 09
4. ly Open the iris completely The figure right shows the manual iris varifocal and lens focus locking screws for a sample lens Refer to your lens documentation for more information If automatic gain control AGC is set to OFF set it to LOW or HIGH on the FUNCTION SETTINGS menu AGC is set to LOW by default a Display the FUNCTION SETTINGS menu b Change AGC to either LOW or HIGH c Select EXIT to save the AGC setting Aim the camera at the farthest object in the field of view Make sure it is at least 6 5 ft 2 m away Fixed focal length lens only a Set the lens focal length to far 00 b Adjust the back focus 1 Use a1 5 mm Allen wrench to loosen the back focus locking screw 2 Turn the lens until the image is focused 3 Tighten the back focus locking screw clockwise A WARNING Do not overtighten the back focus locking screw because you may damage the camera Back focus is a coarse adjustment You will make the fine focus adjustment in the next step c Adjust the lens focus to achieve the best fine focus 6 Varifocal lens only d aA Set the varifocal to wide W and the lens focal length to far OO Adjust the back focus 1 Use a 1 5 mm Allen wrench to loosen the back focus locking screw 2 Turn the lens until the image is focused 3 Tighten the back focus locking screw clockwise A WARNING Do not overtighten the back focus locking screw because you may damage the camera Back foc
5. the menu Press the center button LENS The C10CH Series camera supports both manual and auto iris lenses either fixed focal length or varifocal It automatically senses an auto iris lens as soon as you plug in the connector The camera has a standard CS mount that can accept a C mount lens with a PCMA40 lens adapter To mount the lens onto the camera 1 Make sure the lens does not touch the camera imager when installed 2 Use clean compressed air or a clean dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera imager 3 C mount lens Screw the adapter onto the lens 4 Screw the lens onto the lens mount 5 Auto iris lens Connect the 4 pin connector from the lens to the connector on the side of the camera 6 Perform the lens focusing procedure before using the lens refer to Lens Focus MOUNT The C10CH Series camera can be mounted from either the top or bottom depending on the type of camera mount used in your installation Use a standard 1 4 20 screw The maximum thread depth is 0 25 inches 6 4 mm POWER Connect 12 VDC or 24 VAC power to the back of the camera using the supplied terminal block Use a Class 2 isolated power source for the C10CH camera that can supply 12 VDC 15 or 24 VAC 15 50 60 Hz Maximum power consumption is approximately 3 5 watts C10CH 7X Camera Only The C10CH 7X camera uses a power main supply of 220 to 240 VAC 50 Hz This main supply m
6. us is a coarse adjustment You will make the fine focus adjustment in steps c and d Move the varifocal locking screw up or down to set the field of view Adjust the lens focus to achieve the best fine focus Repeat steps c and d until the focus is correct 7 Manual iris only Adjust the iris for the best picture quality The largest aperture gives the best light sensitivity the smallest aperture gives the greatest depth of field 8 Tighten all lens locking screws A WARNING When tightening the lens locking screws do not overtighten or force any screw 9 Auto iris only Remove the ND filter 10 If necessary reset the AGC setting to its previous value a b G Display the FUNCTION SETTINGS menu Change AGC to OFF LOW or HIGH Select EXIT to save the AGC setting 11 Auto iris only Perform the auto iris lens adjustment procedure refer to DC Iris Level Adjustment REVISION HISTORY Manual Date Comments C2947M 11 07 Original version C2947M A 1 08 Revised setup menus C2947M B 3 08 Made references to manual numbers generic to simplify for future updates C2947M C 4 08 Added power connection information for model C10CH 7X C2947M D 6 08 Revised power requirements for model C10CH 7X C2947M E 6 09 Changed the default iris level setting Pelco and the Pelco logo are registered trademarks of Pelco Inc Copyright 2009 Pelco Inc All rights reserved Worldwide Headquarters 3500 Pelco Way Clovis Californ
7. ust also have a minimum rating of 50 mA CAUTION Unplug the power cord during installation VIDEO Connect a coaxial video cable to the BNC connector on the back of the camera DC IRIS LEVEL ADJUSTMENT Select this option to adjust the electronic properties of the DC drive auto iris lens to the auto iris electronic properties of the camera Perform this procedure before using the camera or each time you change the lens To perform this procedure Focus the camera refer to Lens Focus Aim the camera at a bright flickerless scene Select DC IRIS LEVEL from the MAIN MENU Adjust the DC IRIS LEVEL value for the best image The range is 20 to 20 The default setting is 4 Press the center of the button to save the value 6 Exit the MAIN MENU ee SS Og LENS FOCUS BACK FOCUS After mounting the lens you must focus your C10CH Series camera Adjust both the back focus on the camera and the fine Cc focus on the lens is NOTE The back focus has already been l VARIFOCAL LOCKING SCREW LOCKING SCREW LENS FOCUS LOCKING SCREW adjusted using a standard CS mount lens ene Nis However you might need to adjust it again ons i ee to match the mounted lens net 1 Auto iris only Cover the auto iris lens with a suitable neutral density Ae ND filter This opens the iris A Q completely For best results use a a 1 5 MM ALLEN WRENCH D IRIS ND3 filter LOCKING SCREW Manual iris on
Download Pdf Manuals
Related Search