Paradyne 9000 Series Power Supply User Manual
Contents
1. Housing Keyed Use 120 Vac Power 60 watts 5 slot only No No Supply 100 120 Vac Feature No 9005 F 1 020 Universal 70 watts Access Carrier Yes see figure Yes Power Supply 100 240 Vac only on page 3 Technical Specifications for 120 Vac Power Supply in 5 Slot Housing Specification Criteria Rated Nominal Voltage 100 120 Vac 50 60 Hz Operating Voltage Range 85 132 Vac 50 60 Hz Rated Current Power Consumption typical 1 power supply installed 2 power supplies installed 1 5 Amps 120 Vac 60Hz 1 03 amps 100 Vac 50Hz 1 15 amps Result 207 Btu per hour 120 Vac 60 Hz 100 Vac 50 Hz Result 221 Btu per hour 1 13 amps 1 25 amps 60 watts 60 watts 64 5 watts 64 5 watts Universal Power Supply Keyed i fe Front Rear 97 15746 Technical Specifications for Universal Power Supply in Access Carrier Specification Criteria Rated Nominal Voltage 100 240 Vac 50 60 Hz Operating Voltage Range 85 265 Vac 50 60 Hz Rated Current 4 0 amps Power Consumption typical 1 power supply installed 100 Vac 60Hz 1 7amps 171 watts 120 Vac 60Hz 1 4amps 171 watts 230 Vac 50Hz 0 8amps 167 watts Result 585 Btu per hour 2 power supplies installed 100 Vac 60Hz 1 9amps 177 watts 120 Vac 60Hz 1 5amps 177 watts 230 Vac 50Hz 0 9amps 172 watts Result 609 Btu per hour Installing the Initial Power Supply I2. making sure that you gently push it all the way into the housing If you are still having problems with the power supply contact your service representative Removing the Power Cord When disconnecting a power cord from an installed power supply 1 Disconnect the power cord plug from the ac outlet first 2 Disconnect the power cord from the rear of the power supply Power Failure Recovery In cases of loss and restoration of nominal voltage conditions this product automatically restores to service without manual intervention Copyright 1998 Paradyne Corporation
3. PARADY NE 5 Slot Housing and FrameSaver 9000 Series Access Carrier AC Power Supply Installation Instructions Document Number 9000 A2 GN17 30 August 1998 Before You Begin Both the 5 slot housing and the FrameSaver 9000 Series Access Carrier can hold up to two power supplies A second redundant power supply provides backup for the first Before you start your installation be sure to review the following information CAUTION Refer installation of power supplies to qualified service personnel A HANDLING PRECAUTIONS FOR STATIC SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge ESD during normal operation When performing installation procedures however take proper static control precautions to Y prevent damage to equipment If you are not sure of the proper static control precautions contact your nearest sales or service representative 496 15149 Package Contents Verify that your package contains an ac power supply see following specifications Do I Have the Correct Power Supply The following ac power supplies are available Make sure that you have the correct one for your housing and application NOTE The 120 Vac power supply has a label to warn you to connect the supply only to a 100 120 Vac power source Feature No 9007 F 1 040 For Name Feature Fits in This International Number Wattage Volts
4. lat blade screwdriver turn the screw counterclockwise until it stops turning Then turn the screw clockwise until it locks the power supply in place Power Up Verification A WARNING The power cord contains a 3 wire grounding type plug which has a grounding pin This is a safety feature Grounding of the carrier is vital to ensure safe operation Do not defeat the purpose of the grounding plug by modifying it or by using an adapter Prior to installation use an outlet tester or voltmeter to check the ac receptacle for earth ground If the power source does not provide a ground connection consult an electrician to determine another method of grounding the carrier before proceeding with the installation 1 Insert the IEC connector end of the power cord into the I O card s power IEC 320 inlet 2 Insert the plug into an ac outlet The power supply LED lights Verification Checklist 1 Did the green power supply LED light If not see Troubleshooting Troubleshooting Power Supply Symptom Possible Cause Solutions No power The power cord is not securely Check that the power cord is plugged into the wall receptacle or securely attached at both ends rear housing connection The wall receptacle has no power Check the wall receptacle power by plugging in some equipment that is known to be working Check the circuit breaker Power supply is not fully inserted Reinstall the power supply into the housing
5. nstall the initial power supply into the top slot Use the bottom slot for a second power supply if desired 1 Remove power supply from its shipping box Handle only by the top and bottom edges to avoid damaging the card NOTE The power I O card in the rear of the housing delivers ac power for either one or if needed two power supplies The power I O card is marked with a label indicating the proper voltage 2 At the front of the housing use the attached handle on the power supply to carefully slide the card into the top left slot towards the midplane until you feel it connect Be sure that you slide the card in using the card guides provided on the housing 5 Slot Housing Access Carrier Fastening Screw o o s Sim ore Power Fastening Power Supply Screw Supply 97 15747 3 Locate the screw in the top left corner of the power supply Using a flat blade screwdriver turn the screw counterclockwise until it stops turning Then turn the screw clockwise until it locks the power supply in place Installing the Redundant Power Supply Install the redundant power supply into the bottom slot Disconnect power before servicing 1 Unscrew and remove the filler panel to install a redundant power supply 2 Remove power supply from its shipping box Handle only by the top and bottom edges to avoid damaging the card NOTE The power I O card in the rear of the housing delivers ac power for either one
6. or if needed two power supplies The power I O card is marked with a label indicating the proper voltage 3 At the front of the housing use the attached handle on the power supply to carefully slide the card into the bottom left slot towards the midplane until you feel it connect Be sure that you slide the card in using the card guides provided on the housing 4 Locate the screw in the top left corner of the power supply Using a flat blade screwdriver turn the screw counterclockwise until it stops turning Then turn the screw clockwise until it locks the power supply in place Installing a Replacement Power Supply Install a replacement power supply into either the top or bottom slot Disconnect power before servicing 1 Unscrew and remove the current power supply to install a replacement power supply 2 Remove the new power supply from its shipping box Handle only by the top and bottom edges to avoid damaging the card NOTE The power I O card in the rear of the housing delivers AC power for either one or if needed two power supplies The power I O card is marked with a label indicating the proper voltage 3 At the front of the housing use the attached handle on the power supply to carefully slide the card into the slot towards the midplane until you feel it connect Be sure that you slide the card in using the card guides provided on the housing 4 Locate the screw in the top left corner of the power supply Using a f
Download Pdf Manuals
Related Search