Panasonic VL-FAN1BX Grill Accessory User Manual
Contents
1. 10 11 12 14 PROGRAM button 10 12 R Registration 12 Registration number sticker 8 13 Resetting to the default settings 17 S STATUS indicator 6 10 11 12 14 T Technical data 18 Troubleshooting 16 For your future reference Date of purchase Serial number found on the bottom of the unit Dealer s name and address Dealer s telephone number Attach your sales receipt here Panasonic Communications Co Ltd 1 62 4 chome Minoshima Hakata ku Fukuoka 812 8531 Japan Copyright e This material is copyrighted by Panasonic Communications Co Ltd and may be reproduced for internal use only All other reproduction in whole or in part is prohibited without the written consent of Panasonic Communications Co Ltd 2006 Panasonic Communications Co Ltd All Rights Reserved PFQX2460ZA SC0406SMO XFANT Book2. obstacles between this unit and the sub monitor station the sub monitor station can be used within about 100 m of this unit Usage area varies depending on the location where the unit is installed n places where the radio signal from the main monitor station is stronger the main monitor station directly communicates with the sub monitor station without relaying through the repeater In this case the IN USE indicator may not light up In places where the radio signal from In places where the radio signal the main monitor station is stronger the from the repeater is stronger the main monitor station communicates with main monitor station communicates the sub monitor station without relaying with the sub monitor station by through the repeater relaying through the repeater The IN USE indicator lights in green Radius of radio waves from the main monitor station rA n B Radius of radio waves a from the repeater Important Information Tapping This unit uses digital wireless technology so that a call is rarely intercepted However calls may be tapped by a third party because the unit also communicates using radio waves e Tapping means that the other party intercepts a radio message intentionally or accidentally by using a receiver Using near medical equipment Consult the manufacturer of any personal medical devices such as pacemakers or hearing aids to determine i
3. to another monitor station main monitor station another repeater is needed Can locate the repeater You can install the repeater in a location where 14 in a place where the the STATUS indicator lights in amber or red STATUS indicator does but sound cuts in and out or calls may be not light in green disconnected We recommend a location where the indicator lights in green Can locate the repeater Do not install the repeater outdoors outdoors The repeater does not The STATUS indicator lights in amber or red 14 improve the radio signal or is flashing in red Reinstall the repeater in a location where the indicator lights in green The repeater has been installed near the main 6 monitor station In this location the repeater cannot work effectively because the sub monitor station receives radio waves from only the main monitor station Reinstall it in a location near to where the sub monitor station is used 16 Help Cleaning When cleaning this unit disconnect the AC adaptor from the power outlet Clean the repeater with a soft dry cloth Important Do not use anything containing alcohol polish powder powder soap benzine thinner wax petroleum or boiling water Also do not spray with insecticide glass cleaner or hair spray This could cause a change in color or quality Resetting to the default settings If you want to stop using the repeater or reset it to the defau
4. 5 1 Connect the AC cord to the AC adaptor then connect the AC cord to the power outlet e The POWER indicator lights in green To power outlet 100 240 V AC wa m AC ae A j A at DC plug AC cord 2 Confirm the STATUS indicator The STATUS indicator shows the radio signal status Install the repeater in a location where the indicator lights in green DC IN jack INUSE STATUS POWER Lights in green STATUS indicator Sawe Able to install the Lights in green Strong repeater n places where the Lights in amber indicator lights in amber or red calls may be interrupted Lights in red Weak or disconnected Out of range Unable to install the Flashing in red repeater Change the location 3 Install the repeater Note t is recommended that you install the repeater in a location where the STATUS indicator lights in green although you can install it in other places where the indicator lights in amber or red e Use only the included Panasonic AC adaptor PQLV202 Installation Wall mounting You can mount the repeater on the wall with the included wood screws and washers Mount the repeater on a wall pillar where the wood screws can be firmly fixed 1 Drive the wood screws with washers into the wall pillar Approx gy 60 ai om E an 2 Mount onto the wall directing the wood screws into the slots on the repeater and slide the repeater down u
5. ON isscicasissiadsacatiniasstent XR Rn A ERE ERR 12 e Registering the repeater REGISTRATION ssssssssssseeeneeeeneeneneeeeren 12 To stop using the repeater CANCELLATION sese 13 Installing the repellere queer e senate au ctn anaa aana nane 14 b pep 15 Help Areubles OOo M an rh a aa Ka GN NGGI GEN ANANA ne edenda on pap i 16 cu 17 Resetting to the default settings sseeeeseseesssss 17 General Information Technical data about this Product ccecceeceee cece eee eeeeeeeeeeeeeeeeeeeeeeeeees 18 Important Information Important safety instructions 1 Read these instructions All the safety and operating instructions should be read before the appliance is operated 2 Keep these instructions The safety and operating instructions should be retained for future reference 3 Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to 4 Follow all instructions All operating and use instructions should be followed 5 Do not use this apparatus near water For example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 6 Clean only with dry cloth Do not use liquid cleaners or aerosol cleaners Use a dry cloth for cleaning 7 Do not block any ventilation openings Install in accordance with the manufacturer s in
6. Panasonic Repeater Operating Instructions Model No VL FAN1 BX Thank you for purchasing a Panasonic Repeater This unit is an accessory unit for Panasonic Wireless Video Intercom System You must register this unit to the main monitor station before using Please read these Operating Instructions before using the unit and save for future reference Table of Contents Important Information Important safety instructions susce cundis reno Rx aS KX RUE PRE nane eaaa aana anae rnnt 3 Additional safety information cos oio oqr edo intei aE 4 For best performarniee uices rine DE E ta ga A REV RR 5 Before USING eis aie iin ei Rae eles 5 LOCATION AVOIGING NOISES e 5 e EMVINOMMIS IN es s costs sees aga aaa a aaa a anaa nn ANING ga a aa Kagan aia pan ENNIO NER 5 MSTA OM sab aaa aaa Tab naa ga DANG aaa a ED DN aa ea ba AA ae ieee es eels 6 OWDIEIM USE T 6 STAPPIN G a ea a a Lat a e 7 Using near medical equipmint 1 gaga aka anaa gka tene titt saapas Ka rbai 7 Product names used in these Operating Instructions 7 Introduction Included KEMIS aia ak ctio ies VR VR VV REP a 8 gU STN INS RU t 9 Preparation Location OF controls s isset Aire ite Vea ed eer PER Pu e Ras EUER nM Ede E 10 S nto er gt ho ioe Rrerrrernerte aaa a merce ttt Serres err er n AI MI UI UU LIN E PILAE 11 Installation Registering the repeater to the main monitor station REGIS TRATION CANCELLATI
7. ded with the wireless video intercom system 3 Press and hold PROGRAM on the repeater for about 3 seconds within 2 minutes after completing the main monitor station operations The STATUS indicator flashes in green and then lights up in green after completing the registration Depending on the radio signal status the indicator may light in amber or red or flash in red instead of lighting in green PROGRAM INUSE STATUS POWER PROGRAM L 1 Flashing in green Lights in green 12 Installation 4 Attach the included registration number sticker on the repeater Example 1st repeater 5 Disconnect the AC adaptor and place the repeater in the desired location Even if you disconnect the AC adaptor the registration to the main monitor station is not canceled To stop using the repeater CANCELLATION 1 Perform the cancellation operations using the main monitor station e Read Setting a repeater in the Operating Instructions included with the wireless video intercom system There are no repeater operations included Note Disconnect the AC adaptor from the canceled repeater in order to avoid malfunction You can reset the settings of the repeater to their default settings page 17 13 14 Installation Installing the repeater After completing the registration to the main monitor station install the repeater Refer to For best performance on page
8. ed to endure the mass If the wiring is underground do not make any connections underground WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture WARNING Unplug this unit from power outlets if it emits smoke an abnormal smell or makes unusual noise These conditions can cause fire or electric shock Confirm that smoke has stopped and contact an authorized service center Important Information For best performance Before using It is prohibited to disassemble or modify this unit Contact the dealer where you purchased this unit for repairs When power fails this unit cannot be used Location avoiding noise e This unit uses radio waves to communicate with the devices to be relayed For maximum distance and noise free operation we recommend the following Placing the unit away from electrical appliances such as TVs personal computers microwave ovens or wireless LAN appliances Environment Keep the unit away from electrical noise generating devices such as fluorescent lamps and motors The unit should be kept away from excessive smoke dust high temperature and vibration The unit should not be exposed to direct sunlight Do not place heavy objects on top of the unit When you leave the unit unused for a long period of time unplug it from the power outlet The unit should be kept away from heat sources such as heaters kitchen stoves etc I
9. er is turned on T Light off The power is turned off STATUS Green flashing While registering to the main monitor Jr station I Light off This unit has not been registered to the main monitor station Green light on Lk Strong Shows the radio signal status from the main monitor Ji Amber light on station ird Take notice of this indicator si Red light on when installing page 14 Lic Weak me Red flashing Out of radio wave range so you cannot zl install the repeater here IN USE rv Green light on Repeater is relaying radio waves it Light off Repeater is not relaying radio waves NY EN i og YE Light on alls Flashing Light off 11 Installation Registering the repeater to the main monitor station REGISTRATION CANCELLATION To use the repeater the registration to your main monitor station is required The repeater can only be registered to one main monitor station at a time Registering the repeater REGISTRATION 1 Connect the AC cord to the AC adaptor then connect the AC cord to a power outlet installed nearby the main monitor station e The POWER indicator lights in green To power outlet 100 240 V AC wa gt AC adaptor aA DP Oe eh n DC ug c AC cord 2 Perform the registration operations using the main monitor station DC IN jack INUSE STATUS POWER Lights in green e Read Setting a repeater in the Operating Instructions inclu
10. er source marked on the unit If you are not sure of the type of power supplied to your home consult your dealer or local power company Use only the specified AC adaptor Do not tamper with the plug Make sure the plug is securely inserted Do not touch the plug with wet hands Do not place objects on the power cord Install the unit where no one can step or trip on the cord To reduce the risk of electric shock do not disassemble this unit Take the unit to an authorized service center when service is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the unit is subsequently used Unplug this unit from power outlets and refer servicing to an authorized service center when the following conditions occur A If smoke rises or an unaccustomed noise or smell is discharged from the unit B If metal objects have been dropped inside the unit Do not make any wiring connections when the power supply is turned on 10 11 12 13 Never install wiring during a lightning storm Do not connect the AC adaptor other than the specified voltage Do not connect the AC adaptor to any terminal other than the one specified The AC adaptor is used as the main disconnect device Ensure that the power outlet is installed near the product and is easily accessible Never touch the inside of the unit Be sure to install the unit as specifi
11. f they are adequately shielded from external RF radio frequency energy The unit operates in the frequency range of 2 4 GHz to 2 48 GHz and the power output level can range from 0 03 to 0 175 watts Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so Hospitals or health care facilities may be using equipment that could be sensitive to external RF radio frequency energy Product names used in these Operating Instructions For plain explanation the product names used in these Operating Instructions are described as follows Product figure Description in these Operating Instructions Product name Main monitor station Sub monitor station Main monitor Wireless monitor Introduction Included items amp No Item Quantity Notes Repeater 1 e Q AC adaptor 1 Cord length Approx 3 m AC cord 1 Cord length Approx 1 8 m Wood screws 2 For wall mounting 5 Washers 2 For wall mounting 6 Registration number sticker e Introduction Feature highlights If the sub monitor station is away from the main monitor station or there are the following obstacles between them the radio signal weakens In this case sound cuts in and out and moreover OUT OF RANGE is displayed on the sub monitor station as it cannot be used The repeate
12. lt settings press FACTORY DEFAULT RESET on the bottom 1 Press FACTORY DEFAULT RESET for about 3 seconds using a pointed object such as a ball point pen The STATUS indicator turns off 2 Perform the cancellation operations using the main monitor station e Read Setting a repeater in the Operating Instructions included with the wireless video intercom system Note The registration to the main monitor station is also canceled To use the repeater again register it to the main monitor station 17 General Information Technical data about this product Power supply AC adaptor 100 240 V AC 50 60 Hz 12 0 V DC 750 mA Current consumption Standby Approx 0 05 A During operation Approx 0 08 A Dimensions Approx height 27 mm x width 101 mm x depth 82 mm Approx height 69 5 mm x width 101 mm x depth 82 mm when raising the antenna Mass Weight Approx 85 g Operating environment 0 C to 40 C Up to 90 RH Relative Humidity non condensing Frequency 2 402 GHz 2 481 GHz Index A AC adaptor 8 12 14 AG CONG sasinan baana 8 12 14 Antena ie eoruin cte bao teet reas 10 C Cancellation e 13 Clearing nce 17 D DCIN jack 10 12 14 F FACTORY DEFAULT RESET UTLON WR E a BN 10 17 I Indicators uuu 10 IN USE indicator 10 11 P POWER indicator
13. ntil it is secure About 140 mm of space above the washers is required for raising the antenna Approx 140 mm Wood screw included Washer Wall included Pillar lt Important Do not mount the repeater on walls made of plasterboard ALC Autoclaved Lightweight aerated Concrete panel concrete block or plywood of 18 mm or less in thickness ejejduie 3junoui JEM ww 09 KO1ddy 6 15 Help Troubleshooting Indicator Problem Cause amp Solution Page The POWER indicator is The power is not turned on Connect the AC 14 turned off adaptor The STATUS indicator is The repeater has not been registered Register it 12 turned off to the main monitor station The STATUS indicator is The power of the main monitor station is not flashing in red turned on Turn it on The repeater is out of range Install it in a 14 location where the STATUS indicator lights in green The IN USE indicator The repeater is relaying radio waves lights in green The IN USE indicator is The sub monitor station is being used in a place 6 turned off when using the where the radio signal is stronger from the main sub monitor station monitor station than the repeater This is not malfunction Others Problem Cause amp Solution Page Can register the You cannot register one repeater to two or more m repeater to another main main monitor stations To register
14. r strengthens the radio wave signal and extends the range of use which may resolve these problems when it is installed between the main monitor station and the sub monitor station Possible obstacles Metallic door or shutter Heat insulator including aluminium foil Concrete wall or wall made of galvanized iron sheet When using the sub monitor station on the different floor or house in the same grounds where the main monitor station has been installed e Multiple walls of any sort The registration to the main monitor station is required page 12 You can only register the repeater to one main monitor station at a time Sub monitor station Main monitor station Above illustration is for example purposes Preparation Location of controls E Front View Right side view E Rear view Bottom view 10 Antenna Transmitter Receiver of radio waves PROGRAM button Press to register to the main monitor station Indicators Show the status of this unit and the radio signal level page 11 INUSE STATUS POWER DC IN jack Connect the AC adaptor FACTORY DEFAULT RESET button Press to reset the settings of this unit to their default settings page 17 Indicators Preparation The indicators show the status of this unit and radio wave signals as follows Indicator Status POWER Yr Green light on The pow
15. structions Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating The openings should never be blocked by placing the product on a bed sofa rug or other similar surface 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 9 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 10 Only use attachments accessories specified by the manufacturer 11 Unplug this apparatus during lightning storms or when unused for long periods of time This will prevent damage to the product due to lightning and power line surges 12 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped SAVE THESE INSTRUCTIONS Important Information Additional safety information 1 OORUN 14 15 16 17 18 Use only the pow
16. t should not be placed in rooms where the temperature is less than 0 C or greater than 40 C Damp basements should also be avoided The maximum calling distance approx 100 m may be shortened when the unit is used in the places Where there are following obstacles between this unit and the main monitor station or the sub monitor station Metal doors or metal shutters Heat insulation including aluminium foil Concrete walls or walls made of galvanized iron sheet When using this unit on the different floor or house in the same grounds where the main monitor station has been installed Multiple walls of any sort Operating near 2 4 GHz electrical appliances may cause interference Move away from the electrical appliances Important When you move the unit from a cold place to a warm place wait a little while to let the unit adapt to the change in environment before connection or use In this case condensation such as the formation of dew may occur resulting in error or malfunction Important Information Installation f there are no obstacles between this unit and the main monitor station you can install the unit within about 100 m from the main monitor station Usage area varies depending on the location where the unit is installed Install the unit in the locations where the STATUS indicator lights in green page 14 POWER INUSE STATUS Lights in green While in use if there are no
Download Pdf Manuals
Related Search