Omega Lift 29023 Automobile Parts User Manual
Contents
1. N po Back up Washer 1 a Backup Washer T I Oil Seal I lg lom 20 2 h Washer Metal 2 jolsel 1 N Replacement requires special skills knowledge and equipment Only an authorized service center may perform the repair and or replacement of these items REPLACEMENT PARTS refer to page 9 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number serial number and parts description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 USA Tel 888 332 6419 Fax 816 891 6599 E Mail sales omegalift com Website http www omegalift com SF 3 Figure 4 Replacement Parts Illustration for Model 29025 Replacement Parts List for model 29025 Q 6 G07000 0002 Handle Grip 8 __ G73500 0021 HandeSleve e G48900 0024 Bol MiOx16 G73500 0014 Oil Filler Plug G72500 0014 20 673500 001141 PinDi2 1 21 Gz3500 0012 Roller 1 22 G59305 0005 SpringWashe D10 1 am mar A 2902540 tab ly 1 1 1 2 2 1 1 1 1 2 2 2 Repair Kit Contents Qty a Jong b orng d le EE ay j O ring 17x2 65 f g Om Replacement requires2. special skills knowledge and equipment Only an authorized service center may perform the repair and or replacement of these items m n Back up Washer ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COV
3. ERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies e 10939 N Pomona Ave Kansas City MO 64153 ko 888 332 6419 Nunc sales omegalift com 10 Note Page Contact SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A Tel 888 332 6419 Fax 816 891 6599 OMEGA E Mail sales omegalift com Omega Website http www omegalift com Note Page Contact SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A OMEGAS Tel 888 332 6419 Fax 816 891 6599 RO E Mail sales omegalift com Omega Website http Awww omegalift com
4. Operating Instructions amp Parts Manual PN OMEGA MagicLift Service Jack Low Profile Model Capacity 29023 2 Ton 29025 2 Ton U S Patent No s 6 199 379 5 946 912 A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Leer comprender y seguir las instrucci nes antes To avoid crushing and related injuries de utilizar el aparato NEVER work on under or around El manual de instrucci nes y la informaci n de a load supported only by a hydraulic seguridad deben estar comunicado en lengua del jack operador antes del uso ALWAYS use adequately rated jack No seguir estas indicaci nes puede causar da os stands personales o materiales SFA Companies http www omegalift com Read this manual and follow all the Safety Rules and Operating Instructions before using this product Printed in China 29023 M2 rev 0710 SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack before using The owner and or operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and or operator shall be aware that the use and repair of this product may require special skills and knowledge Instructions and safety information shall b
5. ction Bleeding Venting Trapped Air of Model 29025 With the release valve in the OPEN position 3b and with saddle fully lowered locate and remove the oil filler plug Pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Reinstall the oil filler plug ffi if ut Handle oj Oil Filler Plug under cover plate on reservoir Handle Sleeve Front Wheel Rear Caster Figure 2 Model 29025 Nomenclature 3 Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity Use only on hard level surface This is a lifting device only Immediately after lifting support the load with To avoid crushing and related injuries Never work on under or around a load supported only by hydraulic jack a pair of appropriately rated jack stands Lift only on areas of the vehicle as specified by Always use adequately rated jack stands the vehicle manufacturer e Chock each unlifted tire in both directions Do not move or dolly the vehicle while on the jack Do not use this device to lift level lower support No alterations shall be made to this product nor move a house mobile home travel trailer Failure to heed these markings may result in semper oran Building Srucure personal injury and or property damage Be alert and sober when using this product Do no
6. e conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts including labels are noted Any jack that appears damaged in any way operates abnormally or is missing parts shall be removed from service immediately and the manufacturer notified If you suspect that the jack was subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by a factory authorized service center contact distributor or manufacturer for list of Authorized Service Centers It is recommended that an annual inspection be done by qualified personnel Labels and owner s manuals are available from manufacturer PRODUCT DESCRIPTION The Omega MagicLift Low Profile Service Jack is designed to lift but not support one end of a vehicle This jack must be used in conjunction with a pair of appropriately rated jack stands Each MagicLift Service Jack has a unique feature which provides fast no load lifts to the jacking point at which time it lifts in approximately 0 75 2 increments NEVER use a hydraulic jack as a stand alone device After lifting immediately support the lifted vehicle with a pair of appropriately rated jack stands NEVER place any portion of your body beneath the vehicle when lifting OR lowe
7. he fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Fill until oil nearly covers the inner cylinder as seen from the oil filler hole Reinstall the vent screw oil filler plug TROUBLESHOOTING Lubrication A periodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels casters and pump assemblies move freely Cleaning Periodically check the pump piston and ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store the jack with saddle fully lowered Symptom Possible Causes Corrective Action Jack will not lift load Release valve not tightly closed Ensure release valve tightly closed Load is too heavy Consider higher capacity jack Jack will lift but not maintain pressure Release valve not tightly closed Hydraulic unit malfunction Ensure release valve tightly closed Discontinue use contact Omega Technical Service Jack will not lower after unloading Reservoir overfilled Drain fluid to proper level Linkages binding Clean and lubricate moving parts Poor lift performance Fluid level low Hydraulic unit malfunction Will not lift to full extension Ensure proper fluid level Discontinue use contact Omega Technical Service Fluid leve
8. l low Ensure proper fluid level REPLACEMENT PARTS refer to page 7 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number serial number and parts description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 USA Tel 888 332 6419 Fax 816 891 6599 E Mail sales omegalift com Website http www omegalift com Replacement Parts Illustration for model 29023 Figure 3 Replacement Parts Illustration for Model 29023 6 Replacement Parts List for model 29023 1 G86301 0001 Saddle Pad G86301 0017 Saddle 1 2 G86308 0001 Hydraulic Unit G86301 0004 Front Wheel Assembl 5 G86301 0003 Rear Caster Assembl G86301 0008 Handle Grip G86301 0019 Handle Assembl G86308 0003 Handle Sleeve G48900 0024 Bolt M10x16 G86308 0004 U joint 41 G86301 0014 1 2 18 G86308 0005 2 2 G88009 0016 Bolt M12 G86301 0032 Nut M12 1 1 G59305 0006 Spring Washer D20 G73500 0011 Pin D12 21 G73500 0012 1 23 G69400 0004 Manual 29023 M1 Manual 29023 L0 Label aH 2X 1 1 1 Repair Kit Contents a lom 1 7 Oring 2 jOrng amp t8 41 mo Orin 0 4 BackupWasher 1 o O ring 17x2 65 A A d Uep poo to e BackupWasher 1 po orig 1 _
9. ring SPECIFICATIONS Capacity Jack Size Lx W x H Min Height Max Height 2 1 2 NES 5 8 29025 30 x 13 5 8 x 5 5 8 lift arm Vent screw under cover plate on reservoir front wheel e rear caster Figure 1 Model 29023 Nomenclature 2 PREPARATION Assembly Insert handle into the handle sleeve Tighten the bolton handle sleeve to prevent accidental removal of handle while in use Before Use 1 2 Verify that the product and the application are compatible if in doubt call Omega Technical Service 888 332 6419 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the hazards associated with its use To familiarize yourself with basic operation of this jack locate and turn the release valve handle a Clockwise until firm resistance is felt to further turning This is the CLOSED release valve position used to raise the load b Counter clockwise but no more than 1 2 full turn from the closed position This is the OPEN release valve position used to lower the load Check to ensure that jack rolls freely Raise and lower the unloaded saddle throughout the lifting range before putting into service to ensure the pump operates smoothly Replace worn or damaged parts and assemblies with Omega authorized replacement parts only Lubricate as instructed in Maintenance Se
10. rn the handle counter clockwise but no more than 1 2 full turn If the load fails to lower a Use another jack to raise the vehicle high enough to reinstall jack stands b Remove the malfunctioning jack and then the jack stands c Use the functioning jack to lower the vehicle 4 After removing jack from under the load fully lower the saddle to reduce ram exposure to rust and contamination MAINTENANCE Use only Mobil DTE 13M or equivalent hydraulic jack oil Improper fluid can cause premature failure ofthe jack and the potential for sudden and immediate loss of load Adding oil It is difficult to confirm the correct oil level by simply looking into the oil reservoir after removing the vent screw Correct oil level allows the saddle to reach its advertised maximum height and its advertised minimum height e Too much oil will not allow the saddle to lower completely Too little oil will not allow the saddle to raise completely 1 With saddle fully lowered set jack in its upright level position Remove vent screw 29023 oil plug 29025 2 Fill until oil nearly covers the inner cylinder as seen from the oil filler hole Reinstall the vent screw oil plug Changing oil For best performance and longest life replace the complete fluid supply at least once per year 1 With saddle fully lowered set jack in its upright level position Remove vent screw 29023 oil plug 29025 2 Lay the jack on its side and drain t
11. t operate under the influence of drugs or alcohol OPERATION Lifting Only attachments and or adapters supplied by the manufacturer shall be used Lift only on area of the vehicle as specified by the vehicle manufacturer Follow the vehicle manufacturer s recommended guidelines for lifting Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement 2 Close the release valve by turning the handle clockwise until firm resistance is felt 3 Refer to the vehicle manufacturer owner s manual to locate approved lifting points on the vehicle Center jack saddle under lift point 4 Verify lift point then pump handle to contact lift point To lift pump handle until load reaches desired height 5 Transfer the load immediately to appropriately rated jack stands NEVER use hydraulic jack as a stand alone device ALWAYS transfer the lifted load IMMEDIATELY to a pair of appropriately rated jack stands Use one pair of jack stands per vehicle Rated capacity is per pair only Do not exceed rated capacity Lowering Be sure all tools and personnel are clear before lowering load Slowly open the release valve The more you turn the handle counter clockwise the faster the load will come down Maintain control of the rate of speed at which the load lowers at all times 1 Raise load high enough to clear the jack stands 2 Remove jack stands carefully always used in pairs 3 Slowly tu
Download Pdf Manuals
Related Search