Mercedes-Benz 2008 ML 350 Automobile User Manual
Contents
1. 4 Installation Guide 5 STEP 1 Unpack the Line Card 5 STEP 2 Set the Jumper 5 STEP 3 Set the MDI II MDI X Switch 7 STEP 4 Install the Line Card 8 STEP 5 Connect to the Network 8 User Guide 10 LED Indicators 10 Topology Solutions 10 Link Loss Carry Forward LLCF 11 Technical Specifications 12 Product Safety EMC and Compliance Statements 14 Warranty and Servicing 15 Metrobility Metrobility Optical Systems NetBeacon and twister are registered trademark2. COL collision collision detected R111 12 only Once power is applied to the card verify correct connectivity via the LK LED Topology Solutions 10Mbps 100Mbps 2km CPE CPE CPE CPE CPE CPE CPE 5km 14km CENTRAL OFFICE POP POP Radiance R5000 with Line Cards Radiance R5000 Radiance R5000 1000Mbps Metrobility SONET Gigabit twister Radiance 10Mbps Single Interface Line Cards 11 Link Loss Carry Forward LLCF The Radiance 10Mbps single interface line cards incorporate an LLCF function for troubleshooting a remote connection When LLCF is enabled the FL and TP ports do not transmit a link signal until they receive a link signal from the opposite port The diagram below shows a typical network configuration with a good link status using Radiance line cards for remote connectivity Note that LLCF is enabled as indicated in the diagram Management Station Management Station Switch Hub w SNMP Switch Hub w SNMP Radiance Line Card Radiance Line Card LED lit established link LED unlit no link LLCF is ON LLCF is ON TP TP FL Remote Cable If the connection breaks the line card carries that link loss forward to the switch hub which generates a trap to the management station The administrator can then determine the source of the problem Link Loss Carried Forward Link Loss Carried Forward LED lit established link LED unlit no link Management Sta
3. 100 FD 100 FD RX RX LK LK T X T X TX TX 10 100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 FX RX LK TX M M II x PWR 100 FD RX LK T X TX 10 100 MGT 10 LK AT C O N S O L E 1 PWR A B R ER FX PWR RX RX LK LK M M FL TX TX 10 100 M M PWR RX R X LK AT M M TX T X 100 BASE S M RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 FX PWR RX RX LK LK M M FL TX TX 10 100 M M PWR RX RX LK LK M M FL TX TX 10 100 FX M M RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 R X T X LK TP T X TP R X T X M M M M LK AT 2 Twisted Pair Interface Twisted pair ports provide shielded RJ 45 connectors that support a maximum segment length of 100m Use Category 3 4 or 5 cables Fiber Optic Interface When making network connections make sure that the transmit TX port of the card connects to the receive RX port of the connected device and that the transmit TX port of the
4. have an MDI II to MDI X slide switch for each twisted pair port This switch is positioned directly behind its associated RJ 45 connector and allows simple setup in either straight through default or crossover configurations See the diagrams on pages 5 and 6 for the location of the switch When setting the MDI II to MDI X switch observe the positioning of the following symbols the parallel symbol II indicates a straight through or parallel connection default the cross symbol X indicates a crossover connection These symbols are clearly marked on the printed circuit board Simply slide the switch in the direction of the appropriate symbol Use the following tables as a guide A device that is wired straight through needs one crossover connection If the cable is straight through crossover the MDI II to MDI X Switch Setting should be X II A device that is wired crossover needs a parallel connection If the cable is straight through crossover the MDI II to MDI X Switch Setting should be II X 8 Installation Guide 4 Grasp the card by the front panel as shown Insert the line card into a slot on the chassis making sure that the top and bottom edges of the board are aligned with the top and bottom card guides in the chassis Do not force the board into the chassis unnecessarily It should slide in easily and evenly Slide the card in until the top and bottom edges of the fr
5. A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equip ment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Caution Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian Radio Frequency Interference Statement This Class A digital apparatus meets all requirements of the Canadian Interfer ence Causing Equipment Regulations Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Radiance 10Mbps Single Interface Line Cards 15 Warranty and Servicing Three Year Warranty for Radiance 10Mbps Single Interface Line Cards Metrobility Optical Systems Inc warrants that every Radiance 10Mbps single interface line card will be free from defects in material and workmanship for a period of THREE YEARS from the date of Metrobility shipment This warranty covers the original user only and is not transfera
6. Loss Carry Forward functionality to aid in troubleshooting a remote network connection excluding the R111 12 Refer to the section titled Link Loss Carry Forward for more information MDI II MDI X switch installed on all twisted pair ports to eliminate the need for crossover cables Low bit delay to ensure accurate data flow across the network Strict standards compliance that provides compatibility with other vendors equipment for flexible connectivity Transparency to data frame sizes Radiance 10Mbps Single Interface Line Cards 5 Installation Guide Follow the simple steps outlined in this section to install and start using your Radiance 10Mbps single interface line card NOTE Electrostatic discharge precautions should be taken when handling any line card Proper grounding is recommended i e wear a wrist strap Unpack the Line Card Your order has been provided with the safest possible packaging but shipping damage does occasionally occur Inspect your line card carefully If you discover any shipping damage notify your carrier and follow their instructions for damage and claims Save the original shipping carton if return or storage of the unit is necessary Set the Jumper All Radiance 10Mbps single interface line cards excluding the R111 12 incorporate LLCF Link Loss Carry Forward functionality as an aid in troubleshooting a remote connection The jumper configures the LLCF operation LLC
7. F also can be controlled via console commands or with Metrobility s NetBeacon or WebBeacon management software Refer to the Command Line Interface Reference Guide NetBeacon Element Management Software Installation amp User s Guide or WebBeacon Management Software Installation amp User s Guide for software management information RJ 45 LLCF Jumpers MDI X Position Slide Switch JP1 3 2 1 MDI II Position default OFF ON This is a generalized diagram of the Radiance 10Mbps single interface line cards excluding the R111 12 and is not specific to any particular model Jumper Settings See the diagram above for the location of the LLCF jumper Connect pins 1 and 2 to enable LLCF Connect pins 2 and 3 to disable LLCF default 1 2 6 Installation Guide R111 12 Only On the RJ 45 to BNC line card a jumper is used to set either internal or external termination of the BNC port See the diagram below to locate the jumper labeled JP1 Connect pins 1 and 2 to enable internal 50 termination Connect pins 2 and 3 to enable use of external termination default RJ 45 BNC Jumper JP1 Termination JP1 3 1 10 BASE LK AT COL PWR TP BNC MDI X Position Slide Switch MDI II Position default Radiance 10Mbps Single Interface Line Cards 7 3 Set the MDI II MDI X Switch twisted pair ports only To eliminate the need for crossover cables the Radiance line cards
8. Installation amp User Guide Models R111 12 R111 13 R111 15 R111 16 R111 18 R111 1T RADIANCE 10MBPS SINGLE INTERFACE LINE CARDS PWR LK LK AT TP AT 10BASE PWR LK AT COL 10BASE LK AT FL M M PWR LK AT 10BASE FL LK AT M M PWR LK AT 10BASE LK AT FL S M PWR LK AT 10BASE TP TP TP TP R X T X M M R X T X FL R X T X R X T X BNC This publication is protected by the copyright laws of the United States and other countries with all rights reserved No part of this publication may be reproduced stored in a retrieval system translated transcribed or transmitted in any form or by any means manual electric electronic electromagnetic mechanical chemical optical or otherwise without prior explicit written permission of Metrobility Optical Systems Inc 2001 2002 2004 Metrobility Optical Systems Inc All rights reserved Printed in USA Radiance 10Mbps Single Interface Line Cards Copper to Copper R111 12 ______ RJ 45 to Thinnet Coaxial BNC Copper to Fiber R111 13 ______ RJ 45 to FL multimode SC R111 15 ______ RJ 45 to FL multimode ST R111 16 ______ RJ 45 to FL singlemode ST R111 18 ______ RJ 45 to FL multimode SMA R111 1T ______ RJ 45 to FL multimode ST LH Table of Contents Radiance 10Mbps Single Interface Line Cards Installation amp User Guide Overview
9. _________ 100 Ohms nominal Signal Level Output ______________________________________ 2 0 to 2 8V Signal Level Input __________________________________ 350mV minimum Supported Link Length _________________________________________100m Cable Type ___________________________________ Category 3 4 or 5 UTP For NEBS Level III and EN55024 1998 compliance use only Category 5 STP cables Singlemode F O Interface R111 16 Connector _____________________________________________________ ST Wavelength ________________________________________________1310nm RX Input Sensitivity ______________________________ 32 5 dBm minimum Output Power ___________________________________ 27 dBm to 17 dBm Supported Link Length ___________________________ up to 14km full duplex Cable Type ___________________________________________ 9 125 m F O Thinnet Coax Interface R111 12 Connector __________________________________________ BNC receptacle Termination___________________________________ User Selectable Jumper Supported Link Length ____________________________________ up to 185m Cable Type ______________________________________ RG 58 coaxial cable Radiance 10Mbps Single Interface Line Cards 13 Multimode F O Interface R111 13 R111 15 R111 18 Connector __________________________________________ SC ST or SMA Wavelength _________________________________________________820nm RX Input Sensitivity ______________________________ 32 5 dBm minimum Output Power _____
10. _________________ 21 8 dBm to 16 8 dBm 50 125 m _______________________ 19 dBm to 14 dBm 62 5 125 m Supported Link Length ___________________________ up to 2km full duplex Cable Type ________________________________50 125 or 62 5 125 m F O Multimode Fiber Optic Interface Long Haul Distance Support R111 1T Connector _____________________________________________________ ST Wavelength ________________________________________________1300nm Output Power _______________________ 23 5 dBm to 16 dBm 50 125 m _______________________ 20 dBm to 14 dBm 62 5 125 m Supported Link Length ____________________________ up to 5km full duplex Cable Type __________________________ 50 125 62 5 125 100 140 m F O 14 User Guide Product Safety EMC and Compliance Statements This equipment complies with the following requirements UL CSA EN60950 safety FCC Part 15 Class A EN55022 Class A emissions EN55024 1998 immunity IEC 825 1 Classification Class 1 Laser Product DOC Class A emissions CB This product shall be handled stored and disposed of in accordance with all governing and applicable safety and environmental regulatory agency require ments The following FCC and Industry Canada compliance information is applicable to North American customers only USA FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class
11. ard Guide Slot for Management Card Thumb Screw Blank Panel IMPORTANT Tighten thumb screw to secure each card firmly to chassis before making network connections FX PWR RX RX LK LK M M FL TX TX 10 100 M M FX PWR RX RX LK LK M M FL TX TX 10 100 M M PWR M M OC 12 R X LK LK T X S M R X T X PWR M M OC 12 R X LK LK T X S M R X T X PWR M M OC 12 R X LK LK T X S M R X T X PWR M M OC 12 R X LK LK T X S M R X T X R X T X LK PWR 10 BASE AT R X TP LK AT T X FL S M LK AT 2 Install the Line Card The Radiance 10Mbps single interface line card offers the ease of plug and play installation and is hot swappable The card must be firmly secured to the chassis before network connections are made Follow the simple steps outlined below to install your line card 5 Radiance 10Mbps Single Interface Line Cards 9 LK AT FL PWR AT LK 10 BASE RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 LK AT FL R X PWR FD RX 10 BASE II x PWR 100 FD RX RX LK LK T X M M FL TX TX 10 100 II x II x PWR
12. ble Should the unit fail at any time during this warranty period Metrobility will at its sole discretion replace repair or refund the purchase price of the product This warranty is limited to defects in workmanship and materials and does not cover damage from accident acts of God neglect contamination misuse or abnormal conditions of operation or handling including overvoltage failures caused by use outside of the product s specified rating or normal wear and tear of mechanical components To establish original ownership and provide date of purchase complete and return the registration card or register the product online at www metrobility com If product was not purchased directly from Metrobility please provide source invoice number and date of purchase To return a defective product for warranty coverage contact Metrobility Customer Service for a return materials authorization RMA number Send the defective product postage and insurance prepaid to the address provided to you by the Metrobility Technical Support Representative Failure to properly protect the product during shipping may void this warranty The Metrobility RMA number must be clearly on the outside of the carton to ensure its acceptance Metrobility will pay return transportation for product repaired or replaced in warranty Before making any repair not covered by the warranty Metrobility will estimate cost and obtain authorization then invoice for repair and r
13. connected device con nects to the receive RX port of the card The singlemode SM interface supports a maximum segment length of 14km The multimode MM port on the R111 1T supports a maximum segment length of 5km All other MM ports support a maximum segment length of 2km for remote links Thinnet Coaxial Interface The R111 12 BNC connector supports a maximum segment length of 185m over RG 58 coaxial cable Network Connections Thinnet Coaxial R111 12 RJ 45 to BNC __________________________ 100m 185m Copper to Fiber R111 13 RJ 45 to FL multimode SC _________________ 100m 2km R111 15 RJ 45 to FL multimode ST _________________ 100m 2km R111 16 RJ 45 to FL singlemode ST________________ 100m 14km R111 18 RJ 45 to FL multimode SMA _______________ 100m 2km R111 1T RJ 45 to FL multimode ST _________________ 100m 5km 10 User Guide User Guide This section contains information about the operating features of the Radiance 10Mbps single interface line cards LED Indicators The Radiance 10Mbps single interface line cards provide several LEDs for the visible verification of unit status and proper functionality These LEDs can help with troubleshooting and overall network diagnosis and management There are separate activity AT and link LK indicators for each port When lit the LEDs indicate the following information PWR power normal operation LK link satisfactory link status AT activity receiving data
14. eturn transportation Metrobility reserves the right to charge for all testing and shipping costs incurred if test results determine that the unit is without defect This warranty constitutes the buyer s sole remedy No other warranties such as fitness for a particular purpose are expressed or implied Under no circum stances will Metrobility be liable for any damages incurred by the use of this product including but not limited to lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Authorized resellers are not authorized to extend any other warranty on Metrobility s behalf Product Manuals The most recent version of this manual is available online at http www metrobility com support manuals htm Product Registration To register your product go to http www metrobility com support registration asp 25 Manchester Street Merrimack NH 03054 USA tel 1 603 880 1833 fax 1 603 594 2887 www metrobility com 5660 000010 G 8 04
15. ont panel are flush and even with the top and bottom edges of the chassis To secure the line card to the chassis turn the thumbscrew clockwise until it is snug The card is now properly installed and ready for network connections Connect to the Network To connect the Radiance line card to the network insert the cables into the appropriate connectors as illustrated below Be sure the card is secured to the chassis before making network connections Once power is applied to the unit correct connectivity can be verified via the LK link LED FX PWR RX RX LK LK M M FL TX TX 10 100 M M RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 II x PWR 100 FD RX RX LK LK T X M M FL TX TX 10 100 II x II x PWR 100 FD 100 FD RX RX LK LK T X T X TX TX 10 100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10 100 MGT 10 LK AT C O N S O L E 1 PWR A B R ER FX PWR RX RX LK LK M M FL TX TX 10 100 M M PWR RX RX LK LK M M FL TX TX 10 100 FX M M PWR M M OC 12 R X LK LK T X S M R X T X LX LK LK PWR 1000BASE S M SX M M PWR 1000BASE LK LK SX M M LX S M R X T X Card Guide C
16. s of Metrobility Optical Systems Inc The Metrobility Optical Systems logo is a trademark of Metrobility Optical Systems Inc All others are trademarks of their respective owners The information contained in this document is assumed to be correct and current The manufacturer is not responsible for errors or omissions and reserves the right to change specifications at any time without notice 4 Overview The Radiance 10Mbps single interface line cards offer transparent integration of fiber optic connectivity or copper to coaxial integration in Ethernet networks These innovative solutions provide full signal restoration with low bit delay ensuring accurate data transmission and guaranteeing maximum cable length support All cards are compatible with any Ethernet device Through Metrobility s unique management functionality you can manage remote connections through console commands our NetBeacon or WebBeacon software or with any standard SNMP application This end to end visibility of your network not only simplifies network management but also increases network reliability The Radiance 10Mbps line card provides the following key features Fused power on each line card to protect the rest of the cards in the chassis from a short circuit The power PWR LED on an affected line card will not be lit if its fuse is blown Half or full duplex support Auto polarity support on all twisted pair ports Link
17. tion Management Station Switch Hub w SNMP Switch Hub w SNMP Radiance Line Card Radiance Line Card LLCF is ON LLCF is ON TP TP Broken FL Remote Cable Link Loss Carried Forward LED lit established link LED unlit no link Management Station Management Station Switch Hub w SNMP Switch Hub w SNMP Radiance Line Card Radiance Line Card LLCF is ON LLCF is ON TP Broken TP Cable FL Remote Cable Important When connecting a Radiance line card with LLCF enabled to an auto negotiating device force both sides of the configuration to 10Mbps and either full or half duplex This allows the card to immediately see link pulses and start passing data Line cards are shipped with LLCF disabled OFF 12 User Guide Technical Specifications Data Rate Data Rate ______________________ 10Mbps half duplex 20Mbps full duplex Bit Delay__________________________________________________ lt 5 bits Environmental Power ___________________________________ 5V 1 0 Amp 5W average Operating Temperature ____________________________________ 0 to 50 C Storage Temperature ____________________________________ 30 to 70 C Operating Humidity _________________________ 5 to 95 non condensing Weight_______________________________________________ 5 oz 0 14 kg Network Connections Twisted Pair Interface Connector __________________________________ Shielded RJ 45 8 pin jack Impedance_______________________________
Download Pdf Manuals
Related Search