Memorex MVR4041 VCR User Manual
Contents
1. CHE 117 OWNERS MANUAL Memorex VIDEO CASSETTE RECORDER VIDEOGRABADOR DE CASSETTE MVR4041 ESPANOL ENGLISH ATTENTION ATENCION If you purchase a universal remote control from your local retailer please contact the remote manufacturer for the required programming code Si usted a comprado un control de remoto universal por favor comunicace con el fabricante para el codico de programaccion requerido TV CATV MODE SELECTION SELECCION DE MODO DE TV CATV When shipped from the factory the TV CATV menu option is set to the CATV Cable Television mode If not using CATV Cable TV set this menu option to the TV mode A la salida de f brica la opci n de menu TV CATV est en el modo CATV televisi n por cable Si no se va a utilizar el CATV TV cable cambie la opci n de este men al modo TV VHS Before operating the unit please read this manual thoroughly Antes de utilizar su aparato favor de leer las siguientes instrucciones 4E40401A E COV 07 1 4 1 01 5 03 PM ENGLISH RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL A 11 1 The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous volta2. EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC NATIONAL ELECTRICAL CODE S2898A 4 4E40401A E COV 07 4 Ss 22 ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS 2 POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H 4 1 01 5 03 PM PRECAUTIONS MOISTURE CONDENSATION DO NOT OPERATE THIS VCR FOR AT LEAST TWO OR THREE HOURS WHEN MOISTURE IN THE AIR CONDENSES ON THE VCR WHAT IS MOISTURE CONDENSATION When a cold liquid is poured into a glass for example water vapor in the air will condense on the surface of the glass This is called moisture condensation MOISTURE WILL CONDENSE ON THE UNIT IN THE FOLLOWING CASES When you move this VCR from a cold to a warm place After heating a cold room or under extremely humid conditions WHEN YOU EXPERIENCE THE ABOVE CONDITIONS Plug the power cord into an AC outlet press the POWER button to turn on and leave the unit at room temperature until moisture condensation disappears Depending on the surrounding conditions this may take two or three hours LOCATION AND HANDLE If you cause a static discharge when touching the VCR and the VCR fails to function simply unplug the unit from the wall outlet wait 10 minutes and plug it back in The VCR should return to normal
3. 2 Set the 3 4 Channel selector switch Rear of the VCR to CH 3 or 4 3 ON the TV and set to CH or 4 to correspond with the channel selected in 2 4 Press the TV VCR selector button to select the VCR position The VCR indicator will light in the display 5 Select any channel to receive CH 125 a TV station in your area The channel number will appear on the screen and display for about 4 seconds For a push button TV tuner If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV proceed as follows set the VCR 3 4 channel selector and the TV to CH 3 or 4 play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder Refer to your TV owner s manual for details LANGUAGE SELECTION This VCR can display on the TV screen in the English Spanish or French languages On screen language selection step 2 will automatically appear on the screen when you press the MENU button initially Select the language you prefer first then proceed with the other menu options CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Press the MENU button Press the TRACKING SET or button to select the NEAR ONE LAN
4. 22 Front Audio Video In Jacks A VCR or other video USING ZERO RETURN device may be hooked up for dubbing DUPLICATING A VIDEO TAPE VIDEO HEAD CLEANING BEFORE REQUESTING SERVICE 24 SPECIFIGATIONS ost rts cce aa 25 4E40401A E COV 07 7 4 1 01 5 03 PM A MA 1 11 LOCATION OF CONTROLS 10 REMOTE CONTROL 12 13 14 15 16 17 18 8 4E40401A E P08 13 8 10 11 12 13 14 15 Cassette Loading Slot To insert or remove a video tape REW button In the STOP mode this button rapidly winds the tape backwards In the PLAY mode this button activates Reverse Search PLAY button Press to play a prerecorded tape F FWD button In the STOP mode this button rapidly winds the tape forward In the PLAY mode this button activates Forward Search POWER button Turns the VCR power on and off REC OTR button Press once to start normal recording Additional presses activate One touch Timer Recording STOP EJECT button Press once to stop the tape in any mode Press again to eject the tape CHANNEL W A buttons Used to select a channel for viewing or recording Remote Sensor Signals from the Remote Control are received here AUDIO L R VIDEO In Jacks Audio and video signal cables from an external source can be connected h
5. Press the COUNTER RESET button The counter will appear on the screen NOTES If you rewind the tape from 00 00 00 a minus sign will be displayed in front of the time When you load a tape the counter will change to 00 00 00 The counter does not function on nonrecorded blank sections of the tape When you rewind fast forward or play tapes through blank sections the counter stops 21 4 1 01 5 04 PM ENGLISH 4E40401A E P20 25 22 STEREO RECORDING AND PLAYBACK SEPARATE AUDIO PROGRAM SAP RECORDING STEREO BROADCASTS The VHS Hi Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts When a MTS STEREO broadcast is received the STEREO will appear on the screen and the program can be viewed or recorded in stereo refer to pages 18 and 19 for recording procedures The Hi Fi STEREO recording procedure is the same as for normal recordings STEREO NOTE When using a CATV system stereo TV programs may be transmitted over a mono cable channel In this case the word STEREO will not appear and the sound will be in mono OUTPUT SELECTION When viewing an MTS STEREO TV program or playing a prerecorded VHS Hi Fi STEREO videotape press AUDIO SELECT button to select that the audio be heard through both speakers Normally set to the Hi Fi STEREO position this button can be set to the MONO position if the stereo broadcast or videotape audio is of poor quality The R
6. VIDEO HEAD CLEANING The video heads are the means by which the VCR reads pictures from the tape during playback In the unlikely event that the heads become dirty enough to be clogged no picture will be played back This can easily be determined if during playback of a known good tape there is good sound but no picture picture is extremely snowy If this is the case use a high quality head cleaning system or have them cleaned professionally VIDEO HEAD CLEANING Video head cleaning is needed when the playback picture becomes unclear This signifies that the heads are getting dirty and can occur when playing poor quality or damaged tapes If the heads require cleaning use a equivalent high quality chemical non abrasive wet head cleaning tape or have them cleaned professionally If playing a head cleaning tape in the VCR once does not improve the picture play it several times before requesting service DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE TOP COVER NOTES Video heads may eventually wear out and should be replaced when they fail to produce clear pictures To help prevent video head clogging use only good quality VHS tapes Discard worn out tapes 2 4 1 01 5 04 x o EN o 2 Make sure by first checking the following points SYMPTOM CAUSE BEFORE REQUESTING SERVICE POSSIBLE SOLUTION POWER No power The AC power cord is not
7. and L positions allow the audio from the Right or Left Hi Fi channel to be heard over both TV speakers This button has no effect when viewing a MONO videotape or TV program Each time when you press the button OUTPUT SELECTION display appears on the screen for several seconds Refer to the chart below OUTPUT SOUND HEARD ON BOTH SELECTION SPEAKERS STEREO STEREO LCH LEFT CHANNEL AUDIO RCH RIGHT CHANNEL AUDIO MONO MONO NOTES When playing back a tape that is not recorded in Hi Fi stereo mode the audio will automati cally be monaural When listening to a VHS Hi Fi video tape or MTS broadcast through the VHF UHF jack Audio Video cord not connected the sound will be monaural 22 Your VCR is fitted with an SAP broadcast system which enables you to switch to a SEPARATE AUDIO PROGRAM when viewing a selected channel This function applies only when the program is broadcast in multi languages through the SAP broadcast system CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Press the MENU button Press the TRACKING SET or button to select the SAP option MENU CLOCK SET ITIMER REC SET REPEAT ON POFF AFH SET UP ON OFF
8. E P20 25 29 4 1 01 5 04 PM
9. Find the type of antenna system you are using and follow the connection diagram VCR 1 Combination VHF UHF Antenna with 75 ohm Coaxial Cable 75 ohm Coaxial Cable VCR Matching Transformer 300 ohm Input 75 ohm output not gd 300 ohm Twin Lead Flat Wire Combiner 75 300 ohm Inputs 75 ohm output 7 VHF UHF not supplied 300 ohm Twin Lead Flat Wire lt S 9 Separate VHF and UHF Antennas VCR 75 ohm Coaxial Cable NOTE If both VHF and UHF antennas have 300 ohm twin lead flat wires use a combiner having two 300 ohm inputs and one 75 ohm output NOTES A clear picture will not be obtained by the VCR unless the antenna signal is good Connect the antenna to the VCR properly For better quality recording an indoor antenna or a telescopic antenna is not recommended The use of an outdoor type antenna is required If you are not sure about the connection please refer to qualified service personnel 10 4E40401A E P08 13 10 4 1 01 5 03 PM ZT CO VCR TO TV CONNECTION After you have connected the antenna to the VCR you must connect the VCR to the TV Below are 3 common methods of connecting your VCR to a TV Find the type of TV you are using and follow the connection diagram This VCR has a single 75 ohm output for connection to a TV If your TV has separate VHF and UHF antenna inputs numbers 2 and 3 below use a splitter to connect th
10. the STOP mode b gt will appear on the screen for about 4 seconds The F FWD indicator will light in the display for about 4 seconds FORWARD REVERSE PICTURE SEARCH If you want to see the tape program during REW or F FWD mode press and hold the REW or F FWD button again The backward or forward visual search picture will be seen on the screen Release the button to return to the REW or F FWD mode DIGITAL TRACKING CONTROL When a tape is played the Digital Auto Tracking System automatically adjusts the tracking to obtain the best possible picture If noise bars appear during playback adjust the tracking manually Press the TRACKING SET or button to obtain the best possible picture To resume automatic tracking press the AUTO Tracking button 4 1 01 5 03 PM 4E40401A E P14 19 18 SPECIAL PLAYBACK TO VISUALLY SEARCH FOR DESIRED POINTS When either the F FWD or REW button is pressed in the PLAYBACK mode the speed search picture will appear The CUE indicator or the REVEW indicator will light in the display for about 4 seconds When pressed twice the search picture will increase speed Speed search time depends upon the speed used SP LP or SLP during recording TO WATCH A STILL PICTURE Press the PAUSE STILL button in the PLAYBACK mode The STILL indicator will light in the display for about 4 seconds Press the PAUSE STILL button again to resume normal playback FRAME BY F
11. 01A E P08 13 13 4 1 01 5 03 PM A MA 11 1 AUDIO VIDEO CONNECTIONS If your TV has AUDIO IN and VIDEO IN jacks you can connect your VCR to them to receive a higher quality picture and sound If you have a stereo you can connect a stereo amplifier to enjoy powerful sound AUDIO VIDEO CONNECTION From ANTENNA CATV system To UHF VHF IN To AUDIO L O UT lt p To AUDIO R OUT To AUDIO R IN To VIDEO IN To AUDIO L IN AUDIO VIDEO Cord not supplied 1 Connect the VIDEO OUT jack on the VCR to the VIDEO IN jack on the TV 2 Connect the AUDIO L R OUT jacks on the VCR to the AUDIO L R IN jacks on the TV 3 Set the VIDEO TV selector of your TV to VIDEO STEREO AMPLIFIER CONNECTIONS When you connect your VCR to a Stereo Component System you can view the picture from the VCR while enjoying powerful sound from your audio system From ANTENNA CATV system VIDEO Cord not supplied To VIDEO IN To ANT IN To UHF VHF IN Pee PRA To AUX R AUDIO Cord not supplied Connect the AUDIO L R OUT jacks on the VCR to the AUX L R IN jacks on the stereo amplifier 14 4E40401A E P14 19 14 4 1 01 5 03 PM SETTING THE VIDEO CHANNEL To view playback of a recorded tape or to watch a program selected by the VCR s channel selector the TV must be set to channel 3 or 4 video channel When a TV is connected with the 75 ohm coaxial cable only 1 Turn ON the VCR POWER button
12. 8 programs within 1 month EXAMPLE One touch Timer Recording for 30 minutes CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn on the VCR POWER button When a TV is connected with an audio video cable turn the TV on and select the video input mode on the TV 1 Load a cassette tape with the erase prevention tab intact The clock display will change in the counter display 2 Press the SPEED selector button to select the desired tape speed SP or SLP The counter and SP or SLP will appear on the screen for about 4 seconds 3 Press the direct channel selection buttons or the CHANNEL A or Y button to select the channel to be recorded The channel number will appear on the screen and display for about 4 seconds 4 Press the REC OTR button to begin recording Press the button again to stop recording after 30 minutes Each addi tional press of the REC OTR button will increase recording time as shown in the chart below up to a maximum of 5 hours The OTR and recording time will appear on screen for about 4 seconds EXAMPLE Program a timer recording for the 26th day channel 125 CATV 11 00 11 30 PM on timer program number 1 Tape speed SLP CHECK BEFORE YOU BEGIN Turn on the TV and set to the video channel 3 or 4 Press the TV VCR selector button to select the VCR mode Load a video cassette with the erase prevention tab intact The VCR will automa
13. AUTO REWIND FEATURE the tape will be ejected automatically See the NOTE on page 19 o I o EN o z OL NOTES Always eject the tape when not in use The cassette can be ejected even if the VCR is turn off PLAYBACK To play a prerecorded cassette tape TO START PLAYBACK CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV ek Load a prerecorded tape When loading a cassette tape without the erase prevention tab playback will start auto matically The clock display will change to the counter display N EU Press the PLAY button Playback will start will appear on the screen for about 4 seconds The PLAY indicator will light in the display for about 4 seconds 4E40401A E P14 19 17 TO STOP PLAYBACK Press the STOP button once The tape will stop but remain fully loaded and ready to play E will appear on the screen for about 4 seconds The STOP indicator will light in the display for about 4 seconds This VCR selects the playback tape speed SP LP or SLP automatically TO REWIND OR FORWARD THE TAPE RAPIDLY Press the REW button in the STOP mode 44 will appear on the screen for about 4 seconds The REW indicator will light in the display for about 4 seconds Press the F FWD button in
14. GUAGE option then a press the ENTER button E AUTO REPEAT ON OFF gt ON OFF ENTER MENU 4E40401A E P14 19 15 2 Press the TRACKING SET or button to select the desired language English ENGLISH Spanish ESPANOL or French FRANCAIS then press the ENTER button Press the MENU button until the menu screen is cleared SETTING THE CLOCK You must set the date and time manually for timer recordings EXAMPLE Setting the clock to 8 30 AM March 23 FRI 2001 CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode LANGUAGE IDIOMA LANGUE gt ENGLISH ESPA OL FRANCAIS ENTER MENU When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Press the MENU button Press the TRACKING SET or button to select the CLOCK SET option then press the ENTER button 2 Press the TRACKING SET or button to set the month then MONTH a press the ENTER button e AUTO REPEAT ON OFF SET UP ON OFF WLANGUAGE IDIOMA LANGUE INO NOISE BACKGROUND gt ENTER MENU 1 WED YEAR 2000 Set the day year and time as Step 2 TIME The day of the week will LEETE OANE NEN automatically appear when you set the year 12 00AM MONTH Press and hold down the DA
15. LECT button Switches sound between mono and stereo and SAP when receiving broad casts in stereo or SAP INPUT SELECT button Switches the program for viewing between the VCR and external input sources CALL button Displays the present time day of the week channel counter speed selection and VCR mode on the TV screen SPEED SP SLP selector button Sets the tape speed for recording AUDIO L R VIDEO OUT Jacks Use to output audio and video signal to a TV amplifier or VCR UHF VHF IN ANT Jack Connect a UHF VHF antenna or CATV cable to this jack UHF VHF OUT TV Jack Use to output UHF VHF or CATV signal to a TV 3 4 Channel Selector Switch Selects the channel through which the VCR outputs its signal to a TV AC Power Cord Connect to a 120V 60Hz outlet POWER indicator Recording VCR Timer Record ATR Auto Tracking Tape Speed AM PM Multi Function Display 9 4E40401A E P08 13 9 4 1 01 5 03 PM I o EN o 2 a a 1 8 BASIC CONNECTIONS If you are using an antenna system follow the instructions If you are a cable CATV subscriber skip ahead to page 12 for the proper connections ANTENNA TO VCR CONNECTION The VCR must be connected between the antenna and the TV First disconnect the antenna from the TV and connect it to the VCR Then connect the VCR to the TV Below are 3 common methods of connecting an antenna system to a VCR
16. O VIDEO CONNECTIONS SETTING THE VIDEO CHANNEL ee Real Time Tape Counter with Zero Return The ON SCREEN LANGUAGE SELECTION 15 counter displays real tape time and the zero return SETTING THE CLOCK sss 15 to i a on o SETTING THE CHANNELS see ione 16 position 00 00 00 while the counter can be used to locate programs NOISE ELIMINATION BLUE SCREEN 16 Channel Skip An unwanted channel can be deleted PLAYBACK when using the CHANNEL A or Y button LOADING AND UNLOADING 17 Fluorescent Multi Function Display Selected PLAYBACK cocinas atentan arias 17 functions are immediately indicated on the display SPECIAL PLAYBACK 18 2 Speed Picture Search 3 or 5 times normal speed in CEST SP mode 7X or 9X in LP and 9X or 15 SLP RECORDING LI RECORDING A TV 3 Speed Playback Plays three tape speeds SP LP ONE TOUCH TIMER RECORDING OTR SLP SETTING THE TIMER RECORDING 20 2 Speed Record Records two tape speeds SP SLP ADDITIONAL INFORMATION Stereo SAP Reception This VCR is designed to receive stereo and separate audio program SAP broadcasts ON SCREEN FUNCTION 21 where available STEREO RECORDING AND PLAYBACK 22 SEPARATE AUDIO PROGRAM SAP
17. RAME ADVANCE Press the SLOW button during STILL playback The still picture will advance by one frame each time you press the button Hold the button for continuous frame by frame viewing Press the PAUSE STILL button again to resume normal playback NOTES A few noise bars will appear on the picture during SPEED SEARCH and STILL The audio output is muted during SPEED SEARCH STILL FRAME ADVANCE and SLOW MOTION To prevent damage to the tape special playback is automatically changed to the PLAYBACK mode after 5 minutes SLOW MOTION PLAYBACK Press the SLOW button in the PLAYBACK mode Playback will proceed at 1 10th of the normal speed The SLOW indicator will light in the display for about 4 seconds Press the PLAY button again to resume normal playback NOTE SLOW TRACKING AND VERTICAL LOCK ADJUSTMENT If noise bars appear in the picture during slow motion press the TRACKING SET or button to reduce the noise bars If the still picture jitters excessively press the TRACKING SET or button to stabilize the still picture 18 TO WATCH A TAPE REPEATEDLY CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Press the MENU button Press the TRACKING SET or bu
18. V VHF VHE 2 13 2 13 UHF STD HRC IRC 14 69 14 36 W 37 59 AA WW 60 85 AAA ZZZ 86 94 86 94 95 99 A 5 A 1 100 125 100 125 01 5A 3 Press the direct channel selection buttons or the CHANNEL A or Y button to select the channel to be recorded 1 9 Press 0 twice and then 1 9 as required Example To select 2 Press 002 Press 0 first and then the remaining 2 digits in order from left to right Example Press 012 for 12 Press 2 digits in order Example Press 22 for 22 100 125 Press the 3 digits in order Example Press 110 for 110 10 12 13 99 CH 110 A Press the REC OTR button will appear on the screen for about 4 seconds The REC indicator will light in the display for about 4 seconds CH 110 NOTE Since the VCR has its own TV tuner it is not actually necessary to have the TV turned on in order to make a recording Turning on the TV merely allows confirmation of the proper channel settings on your VCR TO STOP RECORDING Press the STOP button to stop recording E will appear on screen for about 4 seconds The STOP indicator will light in the display for about 4 seconds TO STOP RECORDING TEMPORARILY Press the PAUSE STILL button to avoid recording unwanted material Press again or press the REC OTR button to continue the recording 4E40401A E P14 19 19 will appear on screen for about 4 seconds The PAUSE
19. WSANGUAGE IDIOMA LANGUE ENO NOISE BACKGROUND ONPOFF ENTER MENU 2 Press the ENTER button to select the ON position REC SET 3 I AUTO REPEAT ONOFF Press the MENU button again E Z MANGUAGE IDIOMA LANGUE ENO NOISE BACKGROUND ONPOFF IENTER MENU LISTENING TO SAP When the VCR is turned on or a channel selection is made make certain SAP appears on the screen This means that the Separate Audio Program broad casting is available STEREO SAP SAP USING ZERO RETURN The zero return function provides a convenient method of rapidly returning to the starting point of recording or playback The starting point can be indexed for any location on the tape by pressing the COUNTER RESET button and ZERO RETURN button 1 Press the CALL button to display the counter on the screen When loading a cassette tape the clock will change to the counter automatically in the display Before playback or recording press the COUNTER RESET button to set the counter to 00 00 00 Begin playback or recording Press the STOP button when playback or recording is finished Press the ZERO RETURN button The tape will rewind and automatically stop at the 00 00 00 position a AO N 4 1 01 5 04 PM DUPLICATING A VIDEO TAPE If you connect the VCR to another VCR or camcorder you can duplicate a previously recorded tape Make all connections before turning on the power 1 Load a bl
20. Y 23 FRI button to increase decrease the minute by 10 TIME 8 304M ENTER CANCELIMENU Auto date and time start functioning when you finish setting NOTES After a power failure or disconnection of the power the timer settings will be lost In this case reset the present time Press the CANCEL button to move cursor backward for correction If you want to correct time or date while the clock is functioning press the MENU button then press TRACKING SET or button to select the CLOCK SET option then press the ENTER button To make any adjustments perform steps 2 through 3 1 5 4 1 01 5 03 PM x o l o z 4E40401A E P14 19 16 A 11 1 SETTING THE CHANNELS This VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory skipping over unwanted channels Before selecting channels they must be programmed into the VCR s memory In addition to normal VHF and UHF channels this VCR can receive up to 113 Cable TV channels To use this VCR with an antenna set the TV CATV menu option to the TV mode When shipped from the factory this menu option is in the CATV mode TV CATV SELECTION 1 Press the MENU button MENU WCLOCK SET 2 Press the TRACKING SET AUREAS oNporr WCH SET UP WSAP or button to select the CH SET UP option then press the ENTER button 3 Press the TRACKING SET
21. andard VHF and UHF broadcast channels and up to 113 cable channels One touch Timer Recording OTR Simply by pressing the REC OTR button the VCR can be pro grammed for up to 5 hours of recording with an immedi ate start Automatic Power On When loading a cassette tape this VCR will automatically turn on Automatic Playback When loading a cassette tape with out the erase prevention tab this VCR will automatically turn on and play back the cassette tape at the correct speed Automatic Rewind Stop Eject Power Off When a tape reaches its end during playback and recording it will automatically stop rewind stop eject the tape and the VCR will turn off 4 1 01 5 03 PM E TABLE OF CONTENTS Automatic Repeat Play System When the AUTO REPEAT option is turned on this VCR will automatically CAUTIONS play back the same cassette tape repeatedly IMPORTANT SAFEGUARDS On Screen 3 Language Display This TV can display the screen language English Spanish or French PREPARATION Slow Motion This VCR provides slow motion which of x o EN o z fers steady noise free playback at 1 10 normal speed FEATURES LOCATION OF CONTROLS sse Frame by Frame Advance Press the SLOW button BASIC during still playback to advance the tape one frame at CATV CABLE TV CONNECTIONS 12 a time AUDI
22. ank cassette tape with the erase prevention tab intact into the recording VCR Load a previously recorded tape into the playback VCR or CAMCORDER 2 Press the INPUT SELECT s button to select AUDIO VIDEO input position LINE will appear on the screen The L indicator will light up on the display on the recording VCR Playback VCR To VIDEO OUT To AUDIO R OUT To AUDIO L OUT AUDIO VIDEO Cord not supplied Recording VOR To VIDEO IN To AUDIO R IN To AUDIO L IN Playback Camcorder To AV Jack Recording VCR To AUDIO R IN To AUDIO L IN AUDIO VIDEO Cord not supplied To VIDEO IN For duplicating a previously recorded tape from a camcorder follow the camcorder manufacturer s instructions A typical camcorder dubbing hookup is shown above 4E40401A E P20 25 23 3 Press the REC OTR button on the recording VCR then press the PAUSE STILL button 4 Press the PLAY button on the playback VCR then press the PAUSE STILL button al Press the PAUSE STILL button on both the VCRs simultaneously to begin the duplicating process NOTES It is recommended that you set the SPEED to the SP mode on the recording VCR for best results Unauthorized recording of copyrighted television programs films video tapes and other materials may infringe on the rights of copyright owners and violate copyright laws
23. any for more information concerning connection to their descrambler equipment There are many ways to connect your VCR to a cable system Below are six common methods of connection Incoming x o o z VHF UHF IN ANT ZN Cable gt ALLOWS Recording of one channel while watching another Using the programmable timer to record only the channel selected at the converter box Recording of all channels through the converter box PREVENTS Watching scrambled channels while recording another channel Using the VCR tuner to select channels Splitter VHF UHF IN ANT Incoming E Converter e Cable Descrambler O ALLOWS Recording of nonscrambled channels Recording of one channel while watching another Watching premium channels through the converter while recording nonscrambled channels Using the programmable timer PREVENTS Recording scrambled channels Converter Descrambler Splitter VHF UHF IN ANT Incoming j Converter O Cable Descrambler mac ALLOWS Recording of all channels through the converter box Recording a scrambled or unscrambled channel while watching another scrambled or unscrambled channel Using the programmable timer to record only the channel selected at the converter box PREVENTS Using the VCR tuner to select channels 13 4E404
24. connected Connect the AC power cord to the AC outlet Although the power is on it does not operate Cassette is not inserted Insert a video cassette TV BROADCAST RECEPTION A TV program that is selected by the VCR does not appear on the screen Antenna connection is not correct Connect it correctly Antenna cable is disconnected Reconnect the antenna cable The video channel is not in the correct position Set it to CH 3 or 4 The TV is not set to the video channel 3 or 4 Set the TV channel selector to the 3 or 4 position The TV VCR selector is set at TV mode The TV VCR indicator is not lit Press the TV VCR selector button The TV VCR indicator will light INPUT SELECT is set to the LINE mode Press the INPUT SELECT button to select the TV mode A TV program selected by the VCR does not appear in color The TV CATV menu option setting Set the TV CATV menu option to select TV or CATV mode RECORDING TV recording does not work The erase prevention tab of the video cassette is broken off Place a piece of vinyl tape over the gap INPUT SELECT is set to the LINE mode Press the INPUT SELECT button to select the TV mode Timer recording does not work The time is not set correctly Reset the present time The recording start end time is not set correctly Set the start end time The TIMER REC button has not b
25. d AC outlet NOTES 1 Never connect the AC line cord plug to other than the specified voltage 120V 60Hz Use the attached power cord only 2 If the polarized AC cord does not fit into a non polarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet AC Outlet Wider Hole and Blade Polarized AC Cord Plug One blade is wider than the other 4 1 01 5 03 PM x o EN o z PRECAUTIONS Follow these precautions when using batteries in this device Use only the size and type of batteries specified Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible battery leakage Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions BATTERY INSTALLATION e Open the battery compartment cover Install two AAA batteries Replace the cover EFFECTIVE DISTANCE OF THE REMOTE CONTROL EIN AS LNT NOTES When direct sunlight an incandescent lamp fluorescent lamp or any o
26. ded by RETAC S3125A 4E40401A E COV 07 2 4 1 01 5 03 PM _ gt IMPORTANT SAFEGUARDS 9 VENTILATION Slots and openings in the cabinet back or bottom are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the unit on a bed sofa rug or other similar surface This unit should never be placed near or over a radiator or heat source This unit should not be placed in built in installations such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate If you are not sure of the type of power supply to your home consult your appliance dealer or local power com pany For units intended to operate from battery power or other sources refer to the operating instructions GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the p
27. e TRACKING SET or button to select the unnecessary program and press the CANCEL button to cancel the program molsa Monday to Saturday 4 MO FR Monday to Friday y WKL TH Weekly Thursday MAN STAAT END 7 26 WE 11 00PM 11 30PM 125SLP AFET WANS ENTER CANCEL MENU 4E40401A E P20 25 21 IF THE PROGRAM OVERLAPS ANOTHER NOTE Do not overlap programs as portions of the conflicting programs will be lost The first recording time has priority over the next recording time as shown in the diagram 10 00 8 00 9 00 gt 11 00 Program 1 Program2 gt Deleted Parts Program 3 Non Recorded Portion Parts Prog 2 Recording Control Settings gt NOTES The everyday every week recording can be made continuously until the recording is canceled or the tape reaches the end During timer recording the automatic rewinding mechanism does not function ON SCREEN FUNCTION DISPLAY WHILE WATCHING TV Press the CALL button DAY OF THE WEEK CLOCK CH 125 CHANNEL STEREO AND SEPARATE AUDIO PROGRAM SAP 00 00 00 SP TAPE SPEED REAL TIME COUNTER Press the CALL button again to make the display disappear WHILE OPERATING A TAPE Press the CALL button OPERATING MODE 8 30AM THU CH 125 HI FI STEREO HIFI AUTO REPEAT Op 00 00 00 SP TAPE IN Press the CALL button again to make the display disappear TO SET THE COUNTER TO 00 00 00
28. e VCR to the TV for VHF and UHF reception x o EN o 2 7 N NOTE If a VHF or UHF antenna IN is used set the TV CATV VHE UHE IN menu option to the TV mode OUT 75 ohm Coaxial Cable supplied O TV with single 75 ohm VHF UHF antenna input TV NOTE If a VHF or UHF antenna Splitter is used set the TV CATV IN 75 ohm Input menu option the TV O 75 300 ohm outputs mode 75 ohm Coaxial Cable not supplied OUT supplied pug TV with 300 ohm UHF O Eeee gt lt and 75 ohm VHF antenna inputs NOTE If a VHF or UHF antenna is used set the TV CATV SP id Input menu option to the TV 300 ohm outputs mode 75 ohm Coaxial Cable not supplied OUT supplied TV with 300 ohm UHF O gt and 300 ohm VHF antenna inputs 11 4E40401A E P08 13 11 4 1 01 5 03 PM H C CATV CABLE TV CONNECTIONS Many cable companies offer services permitting reception of extra channels including pay or subscription channels This VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box except for those channels which are intentionally scrambled If you subscribe to a special channel which is scrambled you must have a descrambler box for proper reception n VHF UHF Incoming Cable IN ANT ALLOWS Recording of nonscrambled channels Use of the programmable timer Recording of one channel while watchin
29. e normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation e If the unit has been dropped or the cabinet has been damaged f When the unit exhibits a distinct change in performance this indicates a need for service 20 21 22 23 REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this unit ask the service technician to perform safety checks to determine that the unit is in proper operating condition HEAT The product should be situated away from heat Sources such as radiators heat registers stoves or other products including amplifiers that produce heat NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical
30. een pressed The TIMER REC symbol E is not lit on the display Press the TIMER REC button The is lit on the TIMER REC symbol E display PLAYBACK No picture on screen when playing back a recorded tape The TV is not set to the video channel 3 or 4 Set to the video channel 3 or 4 or adjust the fine tuning button on your TV set Noise bars on screen 24 4E40401A E P20 25 Tracking adjustment beyond range of automatic tracking circuit Adjust tracking manually using the AUTO TRACKING button or the TRACKING SET or buttons on remote control Video heads are dirty Have the video heads cleaned The tape is worn or damaged Try another tape 4 1 01 5 04 PM SYMPTOM CAUSE POSSIBLE SOLUTION REMOTE CONTROL Remote control does not work It is not aimed at the remote sensor Aim it at the remote sensor Distance too far or too much light in the room Operate within 15 feet 5 meters reduce the light in the room There is an obstacle in the path of the beam Clear the path of the beam The batteries are weak Replace the batteries The polarity of the batteries are not inserted correctly Insert correctly TV programs cannot be seen using the TV selector The TV VCR function is in the VCR mode Set to TV or turn off the VCR power button SPECIFICATIONS Vid
31. elect the CH SET UP option then press the ENTER button Press the TRACKING SET or button to select the ADD DE LETE mode then press the ENTER button Select the desired channels to be added or deleted using the TRACKING SET or button Press the ENTER button if you wish to DELETE the channel from memory Press the ENTER button if TO ADD DELETE CHANNELS 1 Press the MENU button ILANGUAGE IDIOMA LANGUE INO NOISE BACKGROUND F ENTER MENU CH SET UP W TV CATV MI AUTO CH MEMORY ADD DELETE IN IENTER MENU ENTER MENU you wish to ADD the unmemorized channel Repeat Steps 3 and 4 for each channel to be added or deleted 5 Press the MENU button three times after adding or deleting all of the desired channels to return to normal TV viewing NOISE ELIMINATION When you don t want to receive a weak signal broadcast the Blue back screen can be obtained by selecting the NO NOISE BACKGROUND ON When the unit is shipped from the factory the NO NOISE BACKGROUND is set to the ON CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV MENU E CLOCK SET WTIMER REC SET E AUTO REPEAT ON OFF WCH SET UP 1 Press the MENU butto
32. eo Head Audio Track Power Source Power Consumption 4 Rotary Heads Hi Fi Sound 2 Tracks MONO Sound 1 Track 120V 60Hz Approx 9 watts Hi Fi Frequency Response Hi Fi Dynamic Range F FWD REW Time More than 90dB and 50 seconds 100Hz to 10 000Hz at SP mode F FWD Approx 4minutes REW Approx 2minutes and 30 seconds with T 120 Cassette Tape Speed Search SP 3 amp 5X Normal Speed LP 7 amp 9 X Normal Speed SLP 9 amp 15 X Normal Speed 9 7 16 D 7 1 los 14 3 16 W x 3 3 4 H x Infrared Direct Access Tuner 181 Channel Freq Synthesized VHF 2 13 UHF 14 69 CATV 14 36 A W 37 59 AA WW 60 85 AAA ZZZ Dimensions 86 94 86 94 95 99 A 5 A 1 Weight 100 125 100 125 Remote Control 01 5A RF Channel Output Inputs Outputs Video Audio Antenna 4E40401A E P20 25 Channel 3 or 4 Switchable In RCA 1Vp p 75 ohm Out RCA 1Vp p 75 ohm In RCA 8dB 50K ohm Out RCA 8dB 1K ohm UHF VHF IN 75 ohm coaxial UHF VHF OUT 75 ohm coaxial Supplied accessories 2x AAA batteries not supplied Remote Control 75 ohm Coaxial Cable Specifications are subject to change without notice Memorex FOR ADDITIONAL SET UP INFORMATION OR CUSTOMER SERVICE PLEASE CALL 1 800 919 3647 25 25 4 1 01 5 04 PM ENGLISH 4E40401A E P20 25 26 4 1 01 5 04 PM 4E40401A E P20 25 27 4 1 01 5 04 PM 4E40401A E P20 25 28 4 1 01 5 04 PM 4E40401A
33. ere Direct Channel Selection buttons 0 9 Allows direct access to any channel STOP button Press to stop the tape MENU button Press to display the on screen menu function TIMER REC button Used to set the VCR to start recording at a preset time SLOW button Press to play back a tape in slow motion or to advance the tape one frame at a time during still playback 4 1 01 5 03 PM 16 17 18 19 20 21 22 23 CLOCK COUNTER selector button Switches between the clock and the real time tape counter COUNTER RESET button Resets the Real Time Tape Counter to 00 00 00 TV VCR selector button Switches between TV and VCR PAUSE STILL button During recording this button temporarily stops the tape The will appear on the screen During playback it stops the tape and displays a still image on the TV screen TRACKING SET buttons During playback they are used to adjust tracking manually Used to set or adjust in the menu mode ENTER button Used to enter the information in the menu mode AUTO TRACKING buttons Allows automatic ad justment of tracking to minimize picture noise during playback CANCEL button Used to clear the selected timer recording program FLUORESCENT DISPLAY One touch Timer 24 25 26 27 28 29 30 31 33 ZERO RETURN button Used to stop the tape when the counter reaches 00 00 00 AUDIO SE
34. g another Converter Descrambler VHF UHF Incoming IN ANT Cable ALLOWS Recording of channels through the converter box scrambled and unscrambled Using the programmable timer to record only the channel selected at the converter box To record from converter descrambler VCR PREVENTS Recording one channel while watching another tuner must be tuned to the converter output Using the VCR tuner to select channels channel usually channel 3 or 4 n Converter Descrambler VHF UHF Incoming Cable IN ANT gt 0 ALLOWS Recording of nonscrambled channels NOTE Use of the programmable timer M you are playing a tape or using the tuner Recording an unscrambled channel while watching puilt into the VCR the converter must be set any channel selected at the converter box to the video channel output of the VCR PREVENTS Recording scrambled channels either 3 or 4 NOTE Whenever a Converter Descrambler box is placed before the VCR you must tune the VCR to the output of the Converter Descrambler box usually channel 3 or 4 12 4E40401A E P08 13 12 4 1 01 5 03 PM HA IMA 117 IMPORTANT Make sure the TV CATV menu option is set to the CATV mode This VCR cannot receive scrambled programs since it does not contain a descrambler In order to receive scrambled programs your existing descrambler must be used Descrambler boxes are available from cable companies Consult your local cable comp
35. ge within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an expe
36. indicator will light in the display for about 4 seconds NOTE The pause function will be released after 5 minutes to prevent damage to the tape or the VCR The VCR will change to the STOP mode NOTE AUTO REWIND FEATURE This VCR will automatically rewind the tape when the tape has ended except during OTR and TIMER REC It will also eject the tape and turn the VCR s power OFF RECORDING ONE PROGRAM WHILE WATCHING ANOTHER While the VCR is recording press the TV VCR selector button to select the TV position The TV VCR indicator will go off and recording will continue Select the TV channel you want to watch by using the TV channel selector x o o z NOTE Some CATV hookups do not permit viewing one channel while recording another See pages 12 13 TO PREVENT AN ACCIDENTAL RECORDING After recording break off the erase prevention tab if you do not wish to record over the tape Screwdriver E Erase prevention tab TO RECORD AGAIN Cover the hole with adhesive tape Be careful the tape does not extend past the edges of the cassette housing Adhesive tape 19 4 1 01 5 03 PM ONE TOUCH TIMER RECORDING OTR The One touch Timer Recording feature provides Timer recording can be programmed on screen with a simple and convenient way to make a timed recording SETTING THE TIMER RECORDING the remote control The built in timer allows automatic unattended recording of up to
37. n then press the TRACKING SET or button to select the NO CI EANGUAGEADIOMML ANGLE NOISE BACKGROUND option NOISE BACKGROUND ONOFF 2 Press the ENTER button to select the ON position 3 Press the MENU button again IN ENTER MENU MENU CLOCK SET M TIMER REC SET WAUTOREPEAT ON OFF WCH SET UP ON OFF MIYANGUAGE IDIOMA LANGUE BNO NOISE BACKGROUND N OFF N ENTER MENU 4 1 01 5 03 PM E O gt z Q gt Z Z O gt Q z Q VHS Use only video cassette tapes marked LOADING Push the center of the tape until it is automatically retracted AUTOMATIC POWER ON The VCR will turn on automati cally and the POWER indicator will light The clock counter display will change to the counter display AUTOMATIC PLAY When loading a cassette tape without the erase preven tion tab playback will start immediately Insert the cassette with its labeled side facing you An inverted cassette cannot be inserted UNLOADING To unload a cassette press the STOP EJECT button on the VCR twice The first press will stop the tape in any mode The second press will eject the tape amp will appear on the screen for about 4 seconds The EJECT indicator will light in the display for about 4 seconds The counter display will change to the clock display for about 4 seconds AUTOMATIC EJECT If the VCR automatically rewinds the tape to the begin ning
38. n a risk of fire or electric shock OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill or spray any type of liquid into the unit OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit be sure the antenna or cable system is grounded to provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA 70 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel _ 4 1 01 5 03 PM A MN 11 1 IMPORTANT SAFEGUARDS 19 DAMAGE REQUIRING SERVICE Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the unit c Ifthe unit has been exposed to rain or water d If the unit does not operat
39. olarized plug If your unit is equipped with a 3 wire grounding type plug a plug having a third grounding pin this plug will only fit into a grounding type power outlet This too is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 10 11 12 4E40401A E COV 07 3 13 14 15 16 17 18 LIGHTNING To protect your unit from a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the unit due to lightning and power line surges POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets and extension cords as this can result i
40. operation Avoid extreme heat or cold 41 F 5 C 104 F 40 C Do not place the VCR on or near appliances which may cause electromagnetic interference e g TV speakers etc Doing so may cause erratic operation of the VCR including picture and or sound distortion or noise Avoid extreme moisture and dust The ventilation holes prevent overheating Do not block or cover these holes Especially avoid covering the holes with soft materials such as cloth or paper Do not insert fingers or any other objects into the cassette loading slot Do not spray cleaner or wax directly on the VCR or use forced air to remove dust Avoid places subject to strong vibration Use in a horizontal flat position only Keep the VCR away from flower vases sinks etc If liquids should be spilled into the VCR serious damage will result If you spill any liquids into the VCR unplug the AC power cord immediately and consult qualified service personnel before attempting to use the VCR again 4E40401A E COV 07 5 When you finish operating the VCR always unload the cassette and turn off the power When you leave your home for a long time unplug the AC power cord To protect the VCR from a lightning storm unplug the AC power cord from the wall outlet and disconnect the antenna POWER SOURCE TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC Insert the AC cord plug into a standard 120V 60Hz polarize
41. or button to select the TV 987 CATV mode ZANUTO CH MEMORY 4 Press the ENTER button to ADD DELETE select the TV or CATV mode The arrow indicates the selected mode TV VHF UHF channels CATV CABLE TV channels 5 Press the MENU button twice to return to normal TV viewing AUTOMATIC MEMORY TUNING The VCR can receive a maximum of 181 channels by presetting the channels into memory CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV E CLOCK SET 1 Press the MENU button ITIMER REC SET Press the TRACKING SET ONPOFF or button to select the CH T TANGUAGE DIOMALANGUE SET UP option then press INO NOISE BACKGROUND the ENTER button EA 2 Press the TRACKING SET 777 or button to select the AUTO CH MEMORY mode then press the ENTER button ON OFF WLANGUAGE IDIOMA LANGUE BNO NOISE BACKGROUND PON OFF ENTER MENU ENTER MENU MENU My TV CATV Y AUTO CH MEMORY IMDD DELETE JENTER MENU 3 The auto tuning will start The channel display will count up and when finished the screen returns to normal Channel numbers will remain red until auto memorizing is complete 16 CH 001 Press the TRACKING SET or button to s
42. rienced radio TV techni cian for help CAUTION Changes or modifications not expressly approved by the partly responsible for compliance with the FCC Rules could void the user s authority to operate this equipment IMPORTANT SAFEGUARDS 1 READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated 2 RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference 3 HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to 4 FOLLOW INSTRUCTIONS All operating and use instructions should be followed 5 CLEANING Unplug this unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 6 ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments as they may cause hazards 2 7 WATER AND MOISTURE Do not use this unit near water For example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool 8 ACCESSORIES Do not place this unit on an unstable cart stand tripod bracket or table The unit may fall causing serious injury and serious damage to the unit 8A An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combina tion to overturn PORTABLE CART WARNING symbol provi
43. ther strong light shines on the Remote Sensor the remote operation may be unstable When there is an obstacle between the VCR and the remote control the remote control may not operate 6 4E40401A E COV 07 6 FEATURES High Quality Picture Technology This video cassette recorder marked HQ incorporates VHS high quality technology A built in detail enhancer is used to boost the recorded signal and provide maximum picture quality in playback It is compatible with other VHS video cassette recorders 4 Video Heads Provides optimal picture quality for special effects playback Hi Fi Stereo Sound With a frequency response of 20 to 20 000 Hz and a dynamic range of better than 90 this VCR provides a level of excellence that rivals compact discs 8 Program 1 Month Programmable Timer with Everyday Every Week Capability The built in timer allows automatic absentee recording of up to 8 TV programs within 1month It is also possible to record a program which is broadcast at the same time everyday or every week On Screen Display and Programming When you select a channel or make other changes the TV will show an indicator on the screen for a few seconds Clock settings timer setting and other set up operations can be carried out using the on screen display menu system Digital Auto Tracking Automatically adjusts tracking during playback for the best possible picture 181 Channel Tuner Receives st
44. tically turn on Check that the clock and date are correct see page 15 When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Press the MENU button M LOCKSET ET Check the TIMER REC SET ANE REGES ONKOFF option is selected then press ISHSETUP ore CH 125 the ENTER button NLANGUAGEIDIOVALANGUE ENO NOISE BACKGROUND 2 Press the TRACKING SET or U HHENTERIMENU button to select one of the program line then press the ENTER button 3 Press the TRACKING SET OTRO 30 or button to select the date CH 125 then press the ENTER button DATE START END CH A d 4 Setthe start time end time LI channel and tape speed as in step 3 NOTE To record from external source set the channel pate start END to L L will appear 26 80 ode next to CH 125 or 69 2 7 E va vi 5 To enter other programs repeat step 2 through 4 Or press the MENU button twice NOTES Press the REC OTR Press Recording time to return to the normal screen DATE START END button to increase the once NORMAL REC TEEN MIETEN time needed for twice 0 30 6 Press the TIMER REC button recording See the 3times 1 00 The power will go off the chart 4 times 1 30 TIMER REC indicator will To cancel OTR press 5 times 2 00 light and the VCR stands by the STOP button or 6
45. times 3 00 for recording turn off the power 7 times 4 00 To cancel timer recording press the button again and 8 times 5 00 the TIMER REC indicator will go out 9 times NORMAL REC 20 4E40401A E P20 25 20 i 4 1 01 5 04 PM SETTING THE TIMER RECORDING TO CORRECT THE SETTINGS While setting press the ENTER button to flash the item to correct then re enter the setting with the TRACKING SET or button When finished press the ENTER button NOTES The VCR cannot be used while the T REC indicator is lit After a power failure or disconnection of the power plug all programmed recording settings must be reset upon resumption of power In this case reset the clock see page 15 and reprogram any timer recordings Press the CANCEL button to move cursor backward for correction TO SET DAILY WEEKLY TIMER When setting the date in step 3 press the TRACKING SET button repeatedly The setting changes as follows Example The current day Friday SU SA Sunday to Saturday 1 One month later minus one day WKL WE lt Weekly Wednesday TO CONFIRM THE SETTINGS Press the TRACKING SET or button to select the TIMER REC SET option in the MENU Then press the ENTER button to display the timer program list Press the MENU button twice to return to the normal screen TO CANCEL A PROGRAM Press the TRACKING SET or button to select the TIMER REC SET option in the MENU Then press th
46. tton to select the AUTO REPEAT option 2 Press the ENTER button to select the ON position 3 Press the MENU button Ifyou press the PLAY button the tape will play over and over until the repeat mode is canceled MENU E CLOCK SET WLANGUAGE IDIOMA LANGUE NOISE BACKGROUND PON OFF IENTER MENU ESAP ON gt Ol WLANGUAGE IDIOMA LANGUE ENO NOISE BACKGROUND PON OFF IENTER MENU 2 will appear if you press the CALL button To cancel press the CALL button again NOTE To cancel repeat mode follow the above steps 1 and 2 then press the ENTER button to select the OFF position Press the MENU button to return to the TV RECORDING A TV PROGRAM RECORDING AND VIEWING THE SAME TV PROGRAM CHECK BEFORE YOU BEGIN Turn ON the TV and set to the video channel 3 or 4 Turn ON the VCR POWER button Press the TV VCR selector button to select the VCR mode When a TV is connected with an audio video cable turn the TV and this VCR on and select the video input mode on the TV 1 Load a cassette tape with the erase prevention tab intact The VCR will automatically turn on The clock display will change in the counter display 2 Press the SPEED selector button to select the desired tape speed SP or SLP The counter and SP or SLP will appear on the screen for about 4 seconds 00 00 00 SP 4 1 01 5 03 PM RECORDING A TV PROGRAM VHF UHF CATV CHANNELS TV CAT
Download Pdf Manuals
Related Search