Lenoxx Electronics H-5560 Telephone User Manual
Contents
1. Check the TONE PULSE switch setting Reset the contrast level of the LCD display The Caller ID display gets dim Check if batteries are properly installed or is blank Check if you have received the first Caller ID record If you have received the first Caller ID record your batteries may be weak Static noise on line or cannot Make sure the handset cords connected properly Or hear calling party or calling replace the COILED HANDSET CORD Any phone store party cannot hear you has these cords in different lengths After some time the cord may have become overstretched or damaged Check if P shows in the display Since the REDIAL PAUSE button has combined function pause function the phone may have been paused Just press the HOOK switch REDIAL does not work 13 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 15 4 8 2005 10 49 AM TROUBLE SHOOTING continued You picked up the phone before the second ring or your phone received unclear call information Static can cause this message If this condition persists contact your local telephone company to ensure that there is no problem with your phone line appears in the display To erase ALL call records make sure the phone is not in use press the DELETE button and hold for 3 seconds the display will show DEL ALL CALLS press the DELETE button again Cannot erase all records in memory Your2. aan T IL DURABRAND 13 MEMORY ADJUSTABLE JUMBO DISPLAY CALLER ID TELEPHONE MODEL PH 5560 OPERATING INSTRUCTIONS e CALLER ID SHOWS YOU CALLER S NAME amp NUMBER 81 NAME amp NUMBER CALLER ID MEMORY TONE PULSE SWITCHABLE DIALING e AUTOMATIC TIME amp DATE DISPLAY ONE TOUCH CALLER ID CALL BACK 3 ONE TOUCH SPEED DIAL BUTTONS e 10 TWO TOUCH SPEED DIAL MEMORY LOCATIONS WALL DESK USABLE REQUIRES 4 AA BATTERIES NOT INCLUDED TO USE THE CALLER ID FEATURES OF THIS PHONE YOU MUST SUBSCRIBE TO CALLER ID SERVICE FROM YOUR PHONE COMPANY AND REMEMBER TO INSTALL BATTERIES NOTE READ AND FOLLOW THESE INSTRUCTIONS BEFORE USING YOUR TELEPHONE IB PH5560 WC E 040505 IB PH5560 W 040505 1 4 8 2005 10 49 AM TABLE OF CONTENTS Important Safety 1 5 5 1 Important Telephone Company amp FCC Information s 2 Location of Controls 2 cc te ee ebb eee e ene was 3 Getting Started Step 1 Checking the Package 4 Step 2 Powering the Phone eee eee eee ee 4 Step 3 Telephone 1 5 5 Step 4 Setting up the Telephone 5 6 Basics Choosing Tone or Pulse 6 Making and Rece
3. i TROUBLE SHOOTING The Caller ID unit will not function until you have subscribed the Caller ID service from your local telephone company Call your local telephone company to have Caller ID service installed on your The Caller ID display does not phone line Check your phone line connections Also show the callers information fresh batteries MUST be installed Make sure all your phone line connections are secure and corrected If it is a private call or a blocked call the callers name and or phone number will not appear in the display You will see time amp date of call plus some dashes or the words UNAVAILABLE or BLOCKED CALL Is any plug disconnected from the modular phone 1 lug No dial tone P P P Is any jack improperly wired Use another phone to test the jack Are all cords connected properly Are all 4 AA Phone does not work batteries installed Make sure they are installed according to the polarity shown gt RINGER switch may be set to OFF debe not ring Slide the switch to HI or LO position Can not dial You may only have PULSE service Set the TONE PULSE switch to PULSE position Cannot store numbers into No batteries are installed or batteries are weak or memory installed up side down Make sure the Caller ID service is active Caller ID does not work Check if the phone is connected to a working wall jack Check if all line cord connections are correct and secure
4. 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception try the following 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for assistance GENERAL The FCC prohibits customer provided terminal equipment to be connected to party lines or to be used in conjunction with coin telephone service This phone is hearing aid compatible IB PH5560 WC E 040505 IB PH5560 W 040505 4 4 8 2005 10 49 LOCATION OF CONTROLS 14 15 17 18 20 21 22 RINGER HI LOW OFF SWITCH adjusts the volume of the ringer or HANDSET CLIP holds the Handset in place when the telephone is 3 4 5 6 16 17 18 COMFORTABLE HANDSET for comfortable use even during
5. PHONE COILED CORD JACK Insert COILED CORD from HANDSET here BATTERY COMPARTMENT place 4 size AA alkaline batteries inside according to the polarities as shown inside the battery compartment RESET SWITCH to reset your phone by inserting a pin into the small hole on the back of the phone 3 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 5 4 8 2005 10 49 AM GETTING STARTED Step 1 Checking the Package Contents Your new PH 5560 jumbo display Caller ID telephone has all the features of a 13 memory telephone plus Caller ID display functions As you unpack this set make sure you have the following items in the package COILED HANDSET CORD STRAIGHT TELEPHONE LINE CORD Lo oJ SHORT STRAIGHT WALL CORD TELEPHONE BRACKET attach to for wall mounting use the back of the base for desk use HANDSET TELEPHONE BASE Step 2 Powering the Phone INSTALLING BATTERIES Before you connect the phone cords follow these steps to install the batteries 1 Push down the battery door tab with a pen or other pointed object and lift the battery door out FIG 1 2 Insert 4 size AA alkaline batteries as shown inside the battery compartment FIG 2 The negative side of the battery touches the battery spring 3 Replace the battery door and snap it shut FIG 3 CAUTION Make sure that the telephone line cord is disconnected before openi
6. Step 4 Setting up the Telephone SETTING UP LCD CONTRAST LANGUAGE AREA CODE TIME AND DATE You may need to set up the LCD contrast language area code time and date for your telephone when you install the batteries for the first time or when you move to an area that has a different area code This is necessary because the phone must distinguish local or long distance calls to properly dial calls from the Caller ID list NOTE During setup if you do not press the DELETE button within 10 seconds the display will get back to normal display mode Press the DISPLAY button repeatedly to adjust the LCD contrast level Press and hold the DELETE button down then press the DOWN button SET LANGUAGE will show in the display The default language E E English F French S Spanish will flash Release the DELETE button and press the UP or DOWN button to choose your desired language flashing Press the DELETE button to confirm and accept Then the display will ask you to set your Area Code While the first digit is flashing you should 1 Press the UP button till the first digit of your area code is displayed flashing 2 Press the DELETE button to accept and go to the next digit gt IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 7 4 8 2005 10 49 AM GETTING STARTED Step 4 Setting up the Telephone continued SETTING UP LCD CONTRA
7. clip and stick it into the small hole at the back of the phone marked RESET for 2 second The display will become blank for about one second then resume to the previous display Note all the information in your phone including the memory numbers you stored and caller ID list will be lost BASICS Choosing Tone or Pulse Dialing Select the type of dialing that you desire or that your telephone system requires by setting the TONE PULSE switch TONE The set will operate using tone dialing PULSE The set will dial using rotary dial type pulses clicking sounds If you are not sure of your dialing system make a trial call with the switch set to TONE If the call connects leave the switch as it is otherwise set it to PULSE NOTE To use caller ID service you will probably need TONE dialing Even when your phone is set to pulse service this phone can be switched to temporary tone for access to services that require tone signaling including Telephone Banking Just press the TONE button after dialing in pulse and your buttons can now be used for tone signaling for this call only 6 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 8 4 8 2005 10 49 AM BASICS Making and Receiving Calls MAKING A CALL 1 Pick up the handset to get a dial tone The hook icon will show in the display 2 Dial the phone number The dialed number appears in the display 3 When you finished talking
8. language is set to French or Spanish To reset the language press and hold the DELETE button and press the DOWN button while is flashing press DELETE button to confirm The language will be set to English mode like Check if you have stored the numbers correctly Memory Dialing does not work by pressing that memory location button s Also numbers can only be stored when fresh batteries are installed correctly Handset falls out of phone base Handset clip was not installed properly for wall when wall mounted use See page 11 for details The caller may have an unlisted or blocked Caller s information is not registered number to prevent Caller ID identification or it to the Caller ID memory may be an overseas call or you may have noise on the line during that call Check with your telephone company if this service is available and if you have subscribed for it Message Waiting does not work Your MEMORY button has no stored number Pressing a Memory button does not Please store the number again Press the display number STORE button dial the number and press the MEMORY locations you want NOTE 1 If problems with your telephone service occur later try to determine if the trouble is with the telephones you own or with the telephone company equipment Unplug the telephone and try it on another jack in a different room or in a neighbor s home to see if the phone line is bad or the phone If the known working
9. may temporarily cease service providing that they 1 Promptly notify the customer 2 Give the customer an opportunity to correct the problem with their equipment 3 Inform the customer of the right to bring a complaint to the Federal Communications Commission pursuant to procedures set out in FCC Rules and Regulations Subpart E of Part 68 The telephone company may make changes in its communications facilities equipment operations or procedures where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations in FCC Part 68 If such changes can be reasonably expected to render any customer terminal equipment incompatible the customer shall be given ad equate notice in writing to allow the customer an opportunity to maintain uninterrupted service RINGER EQUIVALENCE NO REN The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called In most but not all areas the sum of the REN s of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part
10. of the one touch speed dial buttons M1 to M3 3 The phone will dial the numbers you stored into it MAKING CALLS WITH 10 TWO TOUCH SPEED DIALING LOCATIONS 1 Pick up the handset 2 Press the AUTO button first then press the stored two touch memory number 0 9 3 The phone will dial the numbers you stored into it 8 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 10 4 8 2005 10 49 AM aan CALLER ID FEATURES Understanding the Caller ID Service Caller ID allows the caller s phone number to be shown in the display between the first and the second ring of the call also in most cases the caller s name and calling time and date This information will be stored automatically In order to use this feature you must first subscribe to Caller ID service To use the call back feature be sure to enter your area code see pages 5 amp 6 and press the CALL BACK button for correct digits When You Received a Call The phone number appears in the display with the date and time as shown in the example here If your Caller ID service includes the caller s name the caller s name also appears in the display up to 15 letters as well as time amp date of the call this varies by region NOTE The callers phone number and or name will not appear in the following cases The call is made through a telephone company which does not offer Caller ID service including internatio
11. replace the handset into the base RECEIVING A CALL 1 Pick up the handset when the phone rings The hook icon will show in the display 2 After a few seconds the Count Up Call Timer will start 3 When you finished talking replace the handset into the base NOTE When pick up the HANDSET the hook icon will show in the display If this icon shows in the display while the phone is not in use remember to check if the HANDSET is replaced properly Volume Control and Ringer Setting Adjust the handset volume Slide the HANDSET VOLUME control LOUD or NORMAL Set RINGER HI LO OFF switch HI loud rings on incoming calls LO lower rings on incoming calls OFF no ringing on incoming calls NOTE Only this phone will not ring other phones on the same line will continue to ring normally Adjust the ringer level If you have subscribed to the Caller ID service the callers number and or name appears in the display when you received a call see page 9 Last Number Redialing and Pause Function 1 Pick up the HANDSET the hook icon will show in the display 2 Press the REDIAL PAUSE button The last dialed number appears in the display and is automatically dialed TO CHECK THE LAST PHONE NUMBER DIALED While the phone is not in use press the REDIAL PAUSE button The number appears in the display for 10 seconds NOTE If the last dialed number exceeds 15 digits only 15 digits will be displayed PAUSE FUN
12. CTION Example In an office where you need to dial a 9 first to get an outside line Dial the number 9 and press REDIAL PAUSE button and then dial the phone number You will see a F displayed for pause You may also store this into memory Flash Function Useful for call waiting or getting a new dial tone If you are using the telephone when a new call comes in you will hear a beep or click press the FLASH button on your telephone you will put on hold the parter you are having the conversation with and you will be able to talk to the new caller after you finish the conversation with the 2nd caller press FLASH button to return to the 1st call NOTE In order to use this function you need to subscribe to CALL WAITING service from your telephone company mm IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 9 4 8 2005 10 49 AM TELEPHONE FEATURES Memory Dialing You can quickly dial the numbers you stored into the 3 one touch speed dial buttons or 10 two touch speed dial memories STORING PHONE NUMBERS INTO MEMORY 1 Press the STORE button short for programming appears in the display 2 Dial the phone number you want to store You can store up to 22 digits including a TONE and a PAUSE REDIAL PAUSE each of which is counted as one digit 3 For 3 one touch dialing For 10 two touch dialing Press one of the 3 one touch Press AUTO button and then press
13. L OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions or limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state The following charges apply to repairs beyond the warranty period 8 00 Be sure to pack carefully and send postage paid and insured with your money order personal checks will not be accepted and proof of purchase date to LENOXX ELECTRONICS CORP 2 GERMAK DRIVE CARTERET N J 07008 This Class B digital apparatus complies with Canadian ICES 003 For customer service Dial 1 800 315 5885 wonpay THURSDAY 8 00 AM 5 00 PM FRIDAY 8 00 AM 1 00 PM EST or Visit Our Website http www lenoxx com 2005 LENOXX ELECTRONICS CORP 2 GERMAK DRIVE CARTERET N J 07008 MADE amp PRINTED IN CHINA 15 IB PH5560 W C E 040505 pmd 17 4 8 2005 10 50 AM IB PH5560 WC E 040505
14. ST LANGUAGE AREA CODE TIME AND DATE 3 Repeat steps 1 and 2 above to set the 2nd and 3rd digits of your area code AREA CODE EXAMPLE 718 NOTE At any time during setup you may just pick up the handset to dial or receive a call NOTE If you make a mistake you can just do it over again or call customer service for help Your phone will now go to the Time and Date mode press the UP and DOWN buttons to get to the correct number and the DELETE button to accept You do not have to set up the Time and Date because the telephone company will automatically update this with your Caller ID when your phone rings twice or more To get back to the standby mode for dialing press the DELETE button repeatedly until the normal display shows see below for example 10 53 6 18 Example 10 53 a m On June 18th Then the display will ask you to set the LCD contrast you can press the UP or DOWN button to adjust the LCD contrast and press the DELETE button to confirm In general you can press the DISPLAY button directly to set the LCD contrast After setting the LCD contrast language area code time amp date you can adjust the display to the proper position so that you can easy read the information in the display TO RESET THE PHONE In the rare case of abnormal telephone line interference your phone may not work properly and may need to be reset Make sure the phone is hung up use a pointed object like a straighted pape
15. afety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following 1 Read and follow all instructions and warnings 2 Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a slightly dampened cloth only 3 Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 4 Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the phone 5 Slots and openings in back or bottom of the phone are for ventilation and should not be blocked or covered The openings should never be blocked by placing the product on the bed sofa rug or other similar surface This product should never be placed near or over a radiator heat register or a built in installation such as a bookcase or cabinet unless proper ventilation is provided 6 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock Never spill liquid of any kind on the product 7 To reduce the risk of electric shock do not take this telephone apart When service or repair work is required take it to a qualified service representative Opening or removing covers may expose you to dangerous voltage or other
16. he Caller ID List To delete the Caller ID memory one by one 1 Display the Caller s ID you want to delete by pressing UP or DOWN button 2 Press the DELETE button the display will show DEL CALL press the DELETE button once more the display changes to show the next or previous call and the data is deleted 10 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 12 4 8 2005 10 49 AM CALLER ID FEATURES Deleting the Data from the Caller ID List continued To delete ALL the Caller ID memories 1 When the phone is not in use press the DELETE button and hold for 3 seconds the display shows DEL ALL CALLS 2 Press the DELETE button once more the display changes to NO CALLS and all the Caller ID memories including the new call memories are deleted NOTE The new call indicator will flash when there are new calls in the caller ID memory It will be off when all new calls are viewed or all calls are deleted Using Message Waiting Mailbox To use the Message Waiting indication feature you must subscribe to this service if available from your local telephone company Your PH 5560 will only respond to FSK type of message delivery 1 If the message is sent by the telephone company which is preceded by a ring the display will show MESSAGE WAITING and the message waiting symbol will appear in the display and flash 2 After you have retrieved your mes
17. iving Calls 7 Volume Control and Ringer 7 Last Number Redialing and Pause 7 Flash Function 4 v4 Rep ee Re ea ee GaSe eee a tS 7 Telephone Features Memory 8 Storing Phone Numbers into 8 Making Calls with 3 One Touch Speed Dialing Buttons 8 Making Calls with 10 Two Touch Speed Dialing Locations 8 Caller ID Features Understanding the Caller ID Service 9 When you Received a 9 Viewing the Caller ID 5 9 Calling back from the Caller ID List 10 Storing the Phone Numbers from the Caller ID List 10 Deleting the Data from the Caller ID List 10 11 Using Message Waiting Mailbox 11 Wall Mounting Se eee ee Se 11 12 Trouble Shooting 0 0 eee cee ee eee ne ee eee eee nes 13 14 Limited Warranty 54 645 6 ke ae es RR aE 15 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 2 4 8 2005 10 49 AM IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic s
18. long calls HANDSET VOLUME CONTROL adjusts the volume of handset receiver NEW CALL INDICATOR flashes when new calls have come in CALL BACK BUTTON used for calling back from the caller ID list DELETE BUTTON erases an individual record or all records from the Caller ID Memory also used to accept time date and area code during initial setup JUMBO CALLER ID DISPLAY shows the caller s name number and calling time amp date and more UP DOWN BUTTONS review all calls received DISPLAY BUTTON adjusts the LCD contrast level STORE BUTTON used for storing numbers into the one touch or two touch Speed Dial memories ONE TOUCH SPEED DIAL BUTTONS allow you to store numbers and quickly dial them from memory REDIAL PAUSE BUTTON get a new dial tone then press this button to dial the last dialed number also if you need a pause for PABX FLASH BUTTON press to switch calls for call waiting or get a new dial tone 13 AUTO BUTTON allows you to store amp dial numbers from 10 two touch memory locations DISPLAY TAB used to adjust the position of the display LINE CORD JACK insert one end of the telephone line cord here when connecting the telephone turns off ringer for undisturbed privacy TONE PULSE SWITCH selects the desired dialing mode HOOK SWITCH press down to release the line hold it down and then release it to get a new dial tone or for call waiting mounted on a wall BACK OF THE
19. mber press the CALL BACK button once or twice more 4 If the phone number is 10 digit the phone number displayed is 11 digit 1 is added automatically in front of the 10 digit phone number if you want the phone number to be 10 digit press the CALL BACK button once more 5 The phone will dial the number displayed Storing the Phone Numbers from the Caller ID List As the phone keeps the data of up to 81 calls if the 82nd call comes in the phone deletes the oldest data automatically To prevent important data from being deleted you can store them into the 13 speed dial memories 3 one touch or 10 two touch 1 Display the phone number you want to store by pressing UP or DOWN button 2 Press STORE button The display will show STORE OR ADJ press CALL BACK button to adjust the number If the phone number is 10 digit 1 is added automatically in front of the 10 digit phone number 3 For one touch memory For two touch memory Press a one touch speed dial button Press the AUTO button and then one M1 to M3 of the speed dial memories 0 to 9 The phone number is now stored in that memory button NOTE Only the number will be stored not the name NOTE 1 Do not allow more than 3 seconds to elapse between each step of the procedure 2 If the phone is connected to a Private Branch Exchange PABX you may need to add an outside line access digit or a pause see page 8 Deleting the Data from t
20. nal calls The display will show UNAVAILABLE The call is blocked For privacy reasons many states allow callers the option to prevent his or her telephone data from being displayed in the other party s Caller ID display The display will show BLOCKED CALL You have picked up the phone before the second ring If the call is from an office which uses multiple lines the displayed phone number may not match the number you use to call that extension Viewing the Caller ID List The phone stores the data of the last 81 calls received including UNAVAILABLE and BLOCKED CALL calls It keeps track of all calls received even if they were not answered for example if you are not at home You can look through the data in the Caller ID list to check the numbers and names of the calls received 1 Press the DOWN button to view your calls from the newest call 2 Press the UP button to view calls from older calls to newer ones e When you have reached the last newest data by pressing UP button END OF LIST appears If you press UP button again the display will show the first oldest call When you have reached the first oldest data by pressing DOWN button END OF LIST appears If you press DOWN button again the display will show the last newest call You can view the Caller ID list during conversation also by following the steps above NOTE If your telephone is powered by batterie
21. ng the battery door Replace the batteries when the low battery indicator _ appears in the display When the batteries are dead the display will not show anything You can still make or receive calls but you can t use the Caller ID or memory dialing When the batteries are dead your data and settings could be erased 4 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 6 4 8 2005 10 49 AM GETTING STARTED Step 3 Telephone Installation CONNECTING THE TELEPHONE HANDSET 1 Connect the handset coiled cord to the HANDSET REAR OF TH and the left side of the phone WALL TELEPHONE 2 Connect the straight telephone line cord to the LINE CORD jack rear of phone and telephone outlet on the wall If your telephone outlet is not modular contact your telephone company for assistance If you want to mount the telephone on the wall see Wall Mounting on pages 11 amp 12 ATTACHING THE BRACKET FOR DESK USE We recommend you to use the plastic bracket for proper desk use 1 Push both sides of the bracket and insert the 2 wider raised tabs of the bracket into the wider slots on the back of the base according to the arrow on the bracket 2 Press the bracket until the 2 narrow raised tabs of the bracket are inserted into the narrow slots on the back of the base 3 To separate the bracket from the base push both sides of the bracket and pull the bracket out
22. one of the speed dial buttons M1 to dialing keys 0 to 9 to store a phone number in 4 The stored number and the location will be shown in the display press the STORE button to confirm 5 Repeat steps 2 to 4 to store numbers into other memory locations 6 Wait 3 seconds to resume normal display NOTE When the batteries are dead or removed for more than 30 minutes the stored numbers may be erased TIP 1 If you entered a wrong number you may press the hook switch then start from the beginning TIP 2 If you want to store a calling card number into one of your memories you may do this the same way you program a phone number into memory Also if you need a pause in the number simply press the REDIAL PAUSE button on your phone To store a number to be dialed via Private Branch Exchange PABX Before entering a phone number in Step 2 in Storing phone number into memory do as follows 1 Enter the outside line access digit e g 9 2 Press REDIAL PAUSE button for a pause To check the stored number While the phone is not in use press the desired one touch speed dial button or press the AUTO button and the desired two touch memory number 0 to 9 The stored number appears in the display for 3 seconds To change a stored number Just store a new number as described above the old number will be erased automatically MAKING CALLS WITH 3 ONE TOUCH SPEED DIALING BUTTONS 1 Pick up the handset 2 Press one
23. phone does not operate properly on that line contact your local telephone company for assistance 2 If disconnection of your phone ends the problem your phone may be the source of the trouble and it should be tested and repaired if necessary before it is reconnected 3 There are no user maintainable parts or adjustments on this set Should your phone require repairing contact us for instructions except for cords which you can buy at any phone store 14 IB PH5560 W C E 040505 pmd 16 4 8 2005 10 49 AM IB PH5560 WC E 040505 LIMITED WARRANTY We warrant this product to be free from defects in material and workmanship under normal use for a period of 1 year after purchase and we will repair it free of charge or replace it at no charge should it become defective under this warranty providing you submit proof of purchase sales slip with the set During the initial 1 year period after original purchase we will service the set that is returned to LENOXX ELECTRONICS CORP prepaid at no charge After the initial 1 year period expires we will exchange at no charge any part that is defective but will charge for the cost of labor return postage paid by LENOXX This warranty does not apply to any products which have been subject to misuse neglect or accident This warranty does not cover broken cords or cabinet UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP BE LIABLE FOR ANY INCIDENTA
24. risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 8 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions When the cord or plug is damaged or frayed If liquid has been spilled into the product If the product has been exposed to rain or water If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged F If the product exhibits a distinct change in performance 9 Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning 10 Do not use the telephone to report a gas leak in the vicinity of the leak 11 Do not allow anything to rest on the telephone cord Do not locate this product where the cord will be damaged by persons walking on it 12 Never install telephone wiring during a lightning storm 13 Never install telephone jacks in wet locations unless the jack is specially designed for wet locations 14 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
25. s when the batteries are weak the low battery indicator is displayed Change the batteries as soon as possible otherwise the Caller ID list may be erased 93 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 11 4 8 2005 10 49 AM CALLER ID FEATURES Calling back from the Caller ID List A When the Handset is on the Base 1 Display the phone number you want to call back using the UP or DOWN button 2 Press the CALL BACK button the display will show PICKUP OR ADJ 3 If the phone number is 7 digit local call phone number displayed is 7 digit if you want the phone number to be 10 digit area code phone number or 11 digit 1 area code phone number press the CALL BACK button once or twice more 4 If the phone number is 10 digit the phone number displayed is 11 digit 1 is added automatically in front of the 10 digit phone number if you want the phone number to be 10 digit press the CALL BACK button once more 5 Pick up the handset the phone will dial the number displayed B When the Handset is Picked up 1 Display the phone number you want to call back using the UP or DOWN button 2 Press the CALL BACK button the display will show DIALING OR ADJ 3 If the phone number is 7 digit local call the phone number displayed is 7 digit if you want the phone number to be 10 digit area code phone number or 11 digit 1 area code phone nu
26. sage s the telephone company will send a clear signal by a ring to your phone The message waiting symbol will turn off and display shows MSG WAITING 3 Sometimes the telephone company will not send a message clear signal to you and you have to clear the message waiting record manually Just press and hold the DELETE button down and then press the UP button the message will be cleared The message waiting symbol J will be off WALL MOUNTING This phone can be mounted on a wall phone plate If you do not have a modular wall phone plate installed please consult with your phone company or installer to get one or see next page for installation without a wall plate 1 HANDSET CLIP When the phone is mounted on the wall the HANDSET CLIP must be adjusted so it will hold the HANDSET A SLIDE OUT B REVERSE C REPLACE INTO PHONE 2 Use the SHORT STRAIGHT WALL CORD and plug one end into the rear of the phone 3 Plug the other end of the SHORT STRAIGHT WALL CORD into the WALL JACK 4 Put the phone over the WALL PLATE make sure both posts fit into slots on the back of the phone Then slide the phone down to lock the phone onto the WALL PLATE IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 13 4 8 2005 10 49 AM WALL MOUNTING continued Wall Mounting without a Modular Wall Phone Plate Follow these instructions
27. the network interface 15 Be careful when installing or modifying telephone lines 16 Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions gpw SAVE THESE INSTRUCTIONS 1 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 3 4 8 2005 10 49 AM aan IL IMPORTANT TELEPHONE COMPANY amp FCC INFORMATION CAUTION TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK AND PERSONAL INJURY DO NOT OPEN CABINET WE SUGGEST THAT YOU REVIEW THE FOLLOWING INFORMATION PROVIDED BY THE FCC FEDERAL COMMUNICATIONS COMMISSION FCC REGISTRATION This telephone set is registered with the FCC based upon compliance with Part 68 of its rules Connection of this telephone to the nationwide telecommunications network must be through a standard network jack RJ11W or RJ11C which you can order from your telephone company if not already installed NOTE FCC registration does not constitute an expressed or implied guarantee of performance Only the Lenoxx warranty in this booklet covers the performance of this telephone set IMPORTANT FCC INFORMATION In the event that terminal equipment causes harm to the telephone network the telephone company should notify the customer if possible that service may be stopped However where prior notice is impractical the company
28. to mount the phone on the wall without a wall plate Drill one hole 1 Locate a wall stud If it is possible to utilize a wall stud for mounting dry wall expanders or a similar Py type fastener is recommended Consult your local hardware stores for details 2 Drill 2 holes 3 15 16 100 mm apart 3 Put a screw into each hole and leave 5mm of the head exposed to mount the phone screws are not included 4 Connect the straight cord to the phone and jack AH 5 Place the TELEPHONE BASE on the 2 mounting screws and gently push down to lock into place Drill other hole IMPORTANT Before mounting the phone onto the wall select a wall area with sufficient strength If mounting on the wallboard or in an area of questionable strength locate a stud for maximum support of your telephone Installation on Masonry 1 Use a 1 4 masonry drill bit and drill the 2 holes spaced as above 2 Insert plastic anchors and install the 2 screws 3 Leave 3 16 5 mm of the screws exposed to mount the phone 4 Place the TELEPHONE BASE on the 2 mounting screws and gently push down to lock into place anchors and screws are not included MOUNTING AREA MOUNTING SCREW 3 15 46 100 MM 3 16 5 MM LEAVE 3 46 5 MM SCREW EXPOSED DRILL HOLE WITH 1 4 MASONRY BIT 12 IB PH5560 WC E 040505 IB PH5560 W C E 040505 pmd 14 4 8 2005 10 49 AM
Download Pdf Manuals
Related Search