KitchenAid 3186508 Cooktop User Manual
Contents
1. that range is on shipping base or slide range onto cardboard or hardboard Failure to do so could cause damage to floor covering Move range close to cabinet cutout Make electrical connection See Electrical requirements and Electrical connection Panels B and C for details WARNING Personal Injury Hazard Because of the weight and size of this range two or more people are needed to move and safely install it Failure to do so could result in personal injury Use this area to grip Remove and discard shipping base or cardboard or hardboard from under range Lift range up to cabinet opening using the oven opening as an area to grip Center range in cutout Loosen screws and insert spacers shipped inside broiler pan and grill assembly on each side of control console If range does not fit properly check spacers The spacers may need to be cut to fit under the countertop Mark with a pencil where each spacer needs to be cut Loosen both screws to remove spacers Cut across top of each spacer Replace spacers and tighten screws Check that range fits properly on countertop A WARNING To reduce the risk of tipping the appliance the appliance must be securely fastened to the cabinet using the four screws that are provided screws Secure range to cabinet using the four screws through the mounting holes in the front frame of the oven AA WARNING Fire Hazard Do2. 28 5 8 recommended countertop opening 28 1 2 min Note 30 min when bottom of wood or metal cabinet is rotected by not less than 1 4 ame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 stainless Steel 0 024 aluminum or 0 020 countertop height copper 36 min clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet Countertop preparation Front edges You may need to shave or cut the trim of formed or metal front edged countertops to clear the 30 width of cooktop if countertop extends more than 1 1 8 beyond cabinet front additional notching of edge is required to clear step of end cap Countertop must be level Place level on countertop first side to side then front to back If countertop is not level range will not be level Oven must be level for satisfactory baking conditions WARNING Fire Hazard Do Not obstruct the flow of combustion and ventilation air Personal Injury Hazard To eliminate the risk of burns or fire avoid installing cabinet storage above the cooking surface If cabinets are already installed reduce the hazard of reaching over a heated cooking surface by installing a range hood The range hood should extend a minimum of 5 inches out from the bottom front of the cabinets Reaching over a heated cooking surface could result in a serious burn Electrical Shock Hazard It is the custom
3. Not make connection too tight The regulator is die cast Overtightening may crack the regulator resulting in a gas leak and possible fire or explosion manual shutoff valve See Step F on Panel B for proper location flexible connector x ibd 1 2 flare union adapters pressure regulator and normally open valve assembly All connections must be wrench tightened Assemble the flexible connector from the manual shutoff valve or gas supply line from the shutoff valve to the pressure regulator The pressure regulator is located on the left rear lower corner of the range Use pipe joint compound made for use with Natural and L P gas to seal all gas connections Make sure flexible connector is not kinked Seal all openings in floor or wall where range is installed Panel D 11 Open shutoff valve in gas supply line Wait a few minutes for gas to move through the gas line WARNING Fire Hazard Do Not use an open flame to test for leaks from gas connections Checking for leaks with a flame may result in a fire or explosion i112 Use a brush and liquid detergent to test all connections for leaks Bubbles around the connections will indicate a leak If a leak appears shut off gas valve controls and adjust connections Then check connections again NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAME Clean all detergent solution from range 13 T 13 Replace oven door by fitting
4. Part No 3186508 Rev A ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI TIP DEVICE PACKED WITH RANGE e SEE INSTALLATION INSTRUCTIONS IMPORTANT Read and save these instructions 30 t Electric EON Thermal Convection Installer a E Instructions Sli d e in R an g e Homeowner Keep Installation Instructions for future reference with self cleaning oven Save Installation Instructions for local electrical inspector s use Cabinet opening dimensions Before you start Read electrical gas and carpentry instructions Proper installation is your responsibility A qualified technician should install this range Make sure you have everything necessary For minimum clearance to the 1 4 radius required top of the cooktop see Note on both corners of countertop cutout The rahge MUST be Secured to cabinet with four screws provided For detailed instructions see Panel D 7 8 min required between cutout and door or hinge Product dimensions 30 cooktop width 35 7 8 Gas electric location Locate electrical supply junction box within this shaded area or in an adjacent right or left cabinet Locate gas line through the wall or floor within this shaded area Panel A 24 lower cabinet depth 29 3 4 width 25 countertop depth Do Not seal range to side cabinets 1 1 8 max
5. both corners of door over ends of hinges Push door evenly and completely onto hinges Remove nails from hinges If door does not close you have not pushed door completely onto hinges Replace storage drawer Place burner grates over burners and caps Turn on power supply To get the most efficient use from your new dual fuel range read your KitchenAid Use and Care Guide Keep Installation Instructions and Guide close to range for easy reference Numbers correspond to steps Electronic Ignition System initial lighting and gas flame adjustments Cooktop burners use electronic ignitors in place of standing pilots When the cooktop control knob is turned to the HI position the system creates a spark to light the burner This sparking continues until the burner has a flame OFF E L 15 Check the operation of the cooktop burners Push in and turn each control knob to the HI position The flame should light within 4 seconds Check each cooktop burner for proper flame The small inner cone should have a very distinct blue flame approximately 1 2 long The outer cone is not as distinct as the inner cone The LO or simmer setting of each burner has been factory set to the lowest setting available to provide reliable reignition of the burner If any burner does not stay lit on the LO setting contact your KitchenAid dealer for assistance If burners do not light properly turn cooktop control knob to
6. ecessary for cleaning or maintenance shut off gas supply to range Disconnect the gas and electrical supply to the range Remove the screws holding the range to cabinet and pull range out only as far as necessary to disconnect the gas and electrical supply lines Remove the range to complete cleaning or maintenance Move range back into operating position Level range Connect the gas line to the range and check for leaks Replace screws and secure range to cabinet Reconnect the electric supply KitchenAid HOME APPLIANCES Prepared by KitchenAid St Joseph Michigan 49085 If you need assistance The KitchenAid Consumer Assistance Center will answer any questions about operating or maintaining your range not covered in the Installation Instructions The KitchenAid Consumer Assistance Center is open 24 hours a day 7 days a week Just dial 1 800 422 1230 the call is free When you call you will need the range model number and serial number Both numbers can be found on the serial rating plate located on the oven frame behind the oven door If you need service In the event that your KitchenAid appliance should need service call the dealer from whom you purchased the appliance or a KitchenAid authorized service company A KitchenAid authorized service company is listed in the Yellow Pages of your telephone directory under Appliances Household Major Service or Repair You can also obtain t
7. ector 4 5 feet 2 flare union adapters for connection to pressure regulator 1 2 NPT x 3 8 ratchet 1 2 dia router bit Phillips screwdriv wrenc 1 2 or S I D a Measurin B tape or ruler pipe S flat blade adjustable screwdriver wrench Parts supplied for installation sg m eg aG 4 screws Gas supply requirements Observe all governing codes and ordinances a WARNING Fire Hazard Range must be connected to a regulated gas supply L P gas supply must Not exceed a pressure of 14 water column This must be checked by a qualified technician before installing the range Do Not use an open flame to test for leaks from gas connections New A G A design certified flexible metal gas line connector should be used when codes permit Failure to follow these instructions could result in a fire explosion or personal injury This installation must conform with local codes and ordinances In the absence of local codes installations must conform with American National Standard National Fuel Gas Code ANSI Z223 1 latest edition Input ratings shown on the serial rating plate are for elevations up to 2 000 feet For elevations above 2 000 feet ratings are reduced at a rate of 4 for each 1 000 feet above sea level This range is equipped for use with C NATURAL gas It is design certified by A G A for NATURAL and L P gas with appropriate conversion The ser
8. er s responsibility To contact a qualified electrical installer To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSUNFPA 70 latest edition and all local codes and ordinances Failure to do so could result in electrical shock or other personal injury for correct installation It is the customer s responsibility to make sure that the countertop has been properly prepared and that the installation clearances specified on the serial rating plate are met The serial rating plate can be found on the oven frame behind the oven door Check location where range will be installed The location should be away from strong draft areas such as windows doors and strong heating vents or fans The range should be located for convenient use in the kitchen Installation must provide complete enclosure of the sides and rear of range ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST BE SEALED Electrical ground is required See Electrical requirements Proper gas supply connection must be available See Gas supply requirements Cabinet opening dimensions that are shown must be used Given dimensions provide required 0 clearance Cabinet construction This appliance is designed for use in a base cabinet with a depth of 24 The maximum depth for overhead cabinets is 13 The minimum vertical clearance between the cooking s
9. he service company s name and telephone number by dialing free within the continental United States the KitchenAid Consumer Assistance Center telephone number 1 800 422 1230 A special operator will tell you the name and number of your nearest KitchenAid authorized service company Maintain the quality built into your KitchenAid appliance call a KitchenAid authorized service company Printed on recycled paper 1096 post consumer waste 5096 recovered materials Printed in U S A
10. ial rating plate located on the oven frame behind the oven door has information on the type of gas that can be used If this information does not agree with the type of gas available check with your KitchenAid dealer Conversion to L P gas requires Kit No 4175461 available from your KitchenAid Dealer This conversion must be done by a qualified technician Provide a gas supply line of 3 4 rigid pipe to the range location A smaller size pipe on long runs may result in insufficient gas supply Pipe joint compounds made for use with L P gas must be used With L P gas piping or tubing size can be 1 2 minimum L P gas suppliers usually determine the size and materials used on the system hammer Panel B If local codes permit a new A G A design certified 4 5 foot long 1 2 or 3 4 I D flexible metal appliance connector is recommended for connecting this range to the gas supply line Do Not kink or damage the flexible tubing when moving the range A 1 2 male pipe thread is needed for connection to pressure regulator female pipe threads Shutoff valve open position ge to range to gas supply The supply line shall be equipped with an approved shutoff valve This valve is for turning on or shutting off gas to the appliance This valve should be located in the same room but external to the range and should be in a location that allows ease of opening and closing Do Not block acces
11. nce is properly grounded Failure to follow these instructions could result in serious injury or death If codes permit and a separate grounding wire is used it is recommended that a qualified electrician determine that the grounding path is adequate A three wire or four wire single phase 120 240 volt 60 Hz AC only electrical supply or three wire or four wire 120 208 volt if specified on the serial rating plate is required on a separate 15 amp circuit fused on both sides of the line A time delay fuse or circuit breaker is recommended The fuse size must not exceed the circuit rating of the appliance as specified on the serial rating plate The serial rating plate is located on the oven frame behind the oven door THE RANGE MUST BE CONNECTED WITH COPPER WIRE ONLY Wire sizes and connections must conform to the requirements of the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances for the kilowatt rating of the range The appliance should be connected directly to the fused disconnect or circuit breaker box through flexible armored or non metallic sheathed copper cable with grounding wire Locate the junction box to allow two to three feet of slack in the line so that the range can be moved if servicing is ever necessary Do Not cut the conduit A U L listed conduit connector must be provided at each end of the power supply cable at the appliance and at the j
12. s to shutoff valve If rigid pipe is used as a gas supply line a combination of pipe fittings must be used to obtain an in line connection to the range All strains must be removed from the supply and fuel lines so range will be level and in line The regulator must be checked at a minimum of 1 inch water column above the set pressure The inlet pressure to the regulator should be as follows for operation NATURAL GAS Set pressure 5 inches Maximum pressure 14 inches L P GAS Set pressure 10 inches Maximum pressure 14 inches Line pressure testing M Testing above 1 2 psi gauge The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than 1 2 psig 3 5 kPa Testing at 1 2 psi gauge or lower The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 5 kPa Electrical requirements A WARNING Electrical Shock Hazard Electrical ground is required on this appliance Do Not ground to a gas supply pipe Do Not have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in an electrical shock Check with a qualified electrician if you are in doubt as to whether the applia
13. the OFF position Check that burner cap is in proper position Check the power to the unit and the circuit breaker or house fuse Check that gas valves are set to the ON position Repeat Step 16 If a burner does not light at this point contact a KitchenAid dealer for assistance Refer to your Use and Care Guide and check the operation of the oven bake element and broil element L P gas conversion No attempt shall be made to convert the appliance from the specified gas on the rating plate for use with a different gas without consulting the serving gas supplier Conversion to L P gas requires Kit No 4175461 available from your KitchenAid dealer This conversion must be done by a qualified technician Contact your KitchenAid dealer Panel E If range does not operate Check that the circuit breaker is not tripped or the house fuse blown Check that gas valves are turned to ON position more detailed troubleshooting checklist is provided in the Use and Care Guide NOTE Refer to Use and Care Guide for operating instructions and cleaning instructions AWARNING Personal Injury Product Damage Hazard Do Not step lean or sit on the range door Failure to follow this instruction could result in personal injury and or product damage Part No 3186508 Rev A 1994 KitchenAid Registered Trademark of KitchenAid For cleaning and maintenance If removing the range is ever n
14. unction box Wire sizes COPPER WIRE ONLY and connections must conform with the rating of the appliance IE The wiring diagram is found on Panel E The wiring diagram and Tech Sheet can also be found in a pouch attached to the left hand underside of the oven To access remove the storage drawer Electrical connection 4 amp WARNING Electrical Shock Hazard Electrical ground is required on this appliance Do Not connect to the electrical supply until appliance is permanently grounded Disconnect power to the junction box before making the electrical connection This appliance must be connected to a grounded metallic permanent wiring system or a grounding connector should be connected to the grounding terminal or wire lead on the appliance Failure to do so could result in a fire personal injury or electrical shock This appliance is manufactured with the white neutral power supply wire and a cabinet connected green grounding wire twisted together Connect the appliance cable to the junction box through the U L listed conduit connector Complete electrical connection according to local codes and ordinances A Where local codes permit connecting the cabinet grounding conductor to the neutral white junction box wire Cable from Junction power supply box Black Bare or U L listed green wire conduit Cable from connector range Grounded Neutral Figure 1 1 Disconnect the po
15. urface and the overhead cabinets is 30 Overhead cabinets installed at either side of the appliance must be a minimum of 18 above the cooking surface The minimum horizontal distance between the overhead cabinets is 30 Important Observe all governing codes and ordinances Failure to meet codes and ordinances could lead to fire or electrical shock WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do Not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do Not try to light any appliance Do Not touch any electrical Switch Do Not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier Copies of the standards listed may be obtained from National Fire Protection Association Batterymarch Park Quincy Massachusetts 02269 American Gas Association 1515 Wilson Boulevard Arlington Virginia 22209 Tools and materials needed for installation gas line shutoff valve L P resistant pipe joint compound A G A design certified flexible metal conn
16. wer supply 2 Connect together 3 wires green and white appliance cable wires and the neutral white wire in junction box 3 Connect the two black wires together then connect the two red wires together See Figure 1 B If connecting to a four wire electrical system DO NOT connect the cabinet grounding conductor to the neutral white junction box wire Cable from Junction power supply Black wires green U L listed wires Cable from conduit range connector Figure 2 1 Disconnect the power supply 2 Separate the green and white appliance cable wires 3 Connect the white appliance cable wire to the neutral white wire in the junction box 4 Connect the two black wires together then connect the two red wires together See Figure 2 5 Connect the green grounding wire to the grounding wire in the junction box Panel C Now start With range in kitchen fe Remove cooktop burner grates and caps package from shipping box Remove hardware package from side of oven 2 Remove shipping materials tape and protective film from range Do Not remove shipping base at this time 3 Remove the racks and other parts from inside the oven Insert a nail or 5 32 diameter item in the hole of the hinges as far as possible Close the oven door Lift oven door off of hinges and set aside f 5 Remove storage drawer CAUTION Floor Damage Before moving range across floor check
Download Pdf Manuals
Related Search