Kenwood KSC-SW10 Speaker User Manual
Contents
1. If buzzing noise is heard from the speakers when the engine is running attach a line noise filter commercially available to the power lead RCA cord Commercially available parts RCA cord Ignition key gt 0 switch Car fuse box Main fuse Battery 6 English Center unit SUB WOOFER OUT Non fader outpu 151215157 19 9179 POWER SPEAKER REMOTE INPUT linked to damage of the stereo system Be sure to connect it Also painted metal panels etc are not grounded and will not function correctly Be careful Connect the black lead wire ground terminal directly with a screw to an unpainted metal part of the vehicle Turning the power ON without connecting this terminal is Installation Before fixing the speaker in its position be sure to check the sound while it is connected preliminary Caution Install in a location that does not come in the way of driving getting in or out of the vehicle and movement inside the vehicle com2. 50 15 Speaker input sccccsssccsscsssscsssesesssesssesesees 1 0 2 2 DC 14 4 V Operating range 10 5 16 V Maximum current consumption FUSE CAPACITY cccsccsscsccvecscescsesesccrsesscssscsescessesssscssescessese Speaker unit csccscsscescescescescescessescessessecees Passive radiator type Active woofer 120 180 mm 4 3 4 x 7 1 16 cone Passive woofer 120 x 180 mm 4 3 4 x 7 1 16 cone External Width 369 mm 14 1 2 Height 94 mm 3 11 16 Depth 224 mm 8 13 16 Weight 4 2 2 4 101 3 4 kg 7 5 Ib English 9
3. Do not attempt to open or modify the unit for this could cause fire hazard or malfunction After taking the unit out of the polyethylene bag be sure to dis pose of the polyethylene bag out of the reach of children Oth erwise they may play with the bag which could cause hazard of suffocation A CAUTION nstallation and wiring of the product requires expert skill and experience To ensure safety be sure to have your dealer or specialist perform the installation and wiring Do not install the speaker in a spot exposed to direct sunlight or excessive heat or humidity Do not install the speakers in locations which may be subject to water or moisture Do not install the speakers in unstable locations or locations subject to dust f the fuse blows after checking to see if the wiring cord has shorted be sure to replace with the stipulated size amperage use as displayed on the fuse box Using fuses other than the stipulated size can cause fires Check the display To replace the fuse refer to the vehicle instruction manual prevent a short circuit when replacing a fuse disconnect the wiring harness at first Do not use gasoline naphtha or any type of solvent to clean the speaker Clean by wiping with a soft dry cloth Connect the speaker wires to appropriate speaker connectors separately Sharing the negative wire of the speaker or ground ing speaker wires to the metal body of the car can cause this unit
4. Increase the volume to an optimum level on page 8 The speaker cords are connected improp erly Connect the cords correclty by referring to the connection example on page 5 6 Connection terminals are connected im properly Insert the connectors or jacks all the way in to the terminals The remote control cord is unplugged Plug the cord into the REMOTE terminal Sound is small The input level is set to low Sound quality is bad sound is distorted The input level is set to high Turn the LEVEL control knob and set the in put level to an optimum level Sound is unnatural The speaker cords are connected with incor rect positive negative polarity The grounding pin black of the 10 pin connection cord is poorly contacted Connect the cords correctly by referring to the connection example on page 5 6 Attach the grounding terminal to the metal lic section of the vehicle not a coated sur face by tightly screwing it The balance between the front speakers or between those and the rear speakers are not well adjusted Adjust the tone balance by switching the PHASE switch to 0 or 180 as required on page 8 Specifications The following ratings and design are subject to change without notice TY Pe Powered Enclosed Subwoofer Input sensitivity impedance RCA 22 4 4 00 0 10 0
5. PWR PWR 7 50 Power ON Power OFF The illumination on the subwoofer turns on and off in an interlocked operation with the PWR indicator on the remote control unit Adjusting the sound Remote control operation Turn the FREQUENCY control knob to adjust the cut off frequency frequencies higher than this frequency are cut off Turn the LEVEL control knob to adjust the low frequencies to the desired level Adjust the low frequency phase The low frequency tone may be variable depending on the po sition of the unit its orientation or the turn over frequency This can be adjusted by changing the position of the PHASE switch Set this switch to either position according to your liking 0 indicates the normal phase 180 means the reverse phase PHASE 180 O o Turn the FREQUENCY control knob to adjust the balance between the bass from the rear speakers and the bass from this unit as desired MAX 50Hz a 120Hz MIN LOW FREQUENCY HIGH Fuse exchange Exchange with the specified capacity fuse Caution sure to replace with same capacity amperage as displayed on the fuse This product is 10 Removal Open the cover Grasp with pliers and pull up 8 English Insertion Replacement fuse 10 Insert the fuse gently into the fuse holder and push in all the way with your finger Close the cover Tr
6. or rear speaker Left Right connect the blue white wire to the accessory line ignition key switch ACC posi g tion line Fuse 10A Car fuse box POWER SI Mu PEAKER REMOTE T White Black Gray Black Blue White If buzzing noise is heard from the speakers when the engine is running attach a line noise filter commercially available to the power lead Ignition key switch Yellow Car fuse box Main fuse Caution Connect the black lead wire ground terminal directly with a screw to an unpainted metal part of the vehicle Turning the power ON without connecting this terminal is Battery linked to damage of the stereo system Be sure to connect it Also painted metal panels etc are not grounded and will not function correctly Be careful m Z vn English 5 Connecting the subwoofer to the subwoofer non fader output of the center unit Front speaker Center unit output of the center unit Connect the subwoofer to the subwoofer output non fader output or the RCA jacks for the front Notes ENGLISH 9 RCA Commercially konii Sterne available parts When
7. the center unit output is a single RCA jack use an Read the instruction manuals for the connected components such as the center unit as well as this instruction manual Please purchase an RCA cord that is commercially available separately Use the provided RCA cord 9 for connection between the sub woofer and the separately purchased RCA cord When the center unit incorporates a DSP connect the subwoof er to the subwoofer output non fader output or to the RCA RCA cord that converts the output into the two RCA jacks as shown above The subwoofer output will be halved if the conversion cord is not used be attenuated due to the DSP effect Examples The following shows a typical connection for effective car stereo enjoyment Connect your system by referring to the example A Caution Under any circumstances never ap ply inputs to the hashed terminals and simultaneously Caution Cover unused terminals with insula tion tape to avoid short circuits jacks for the front output Do not connect to the RCA jacks for he rear output as the low frequency reproduction effect may If there is no power control terminal in the center unit con nect the blue white wire to the accessory line ignition key switch ACC position line Car fuse box Blue White Fuse 10A Yellow Yellow
8. to fail Do not connect cables and leads to both RCA cord input jacks and the speaker input terminals simultaneously for this may cause malfunction or damage When making a hole under a seat inside the trunk some where else in the vehicle check that there is nothing hazardous on the opposite side such as a gasoline tank brake pipe or wir ing harness and be careful not to cause scratches or other dam age For ground wire mounting do not fasten the wire to an airbag steering or brake line system or other critical safety unit bolts or nut Can cause accidents When mounting be sure to mount in a place that will not inter fere with driving or be dangerous to passengers during sudden braking etc Cause of injury or accidents After installing the unit check to make sure that electrical equip ment such as the brake lamps turn signal lamps and windshield wipers operate normally 2 English Information on Disposal of Old Electrical and Electronic Equipment applicable for EU countries that have adopted separate waste collection systems Products with the symbol crossed out wheeled bin cannot be disposed as house hold waste Sa Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste by products Contact your local authority for details in locating a recycle facility nearest to you Proper recycling and waste disposal will hel
9. KENWOOD KSC SW10 POWERED ENCLOSED SUBWOOFER CAISSON D EXTREME GRAVE AMPLIFIE MODE D EMPLOI GEKAPSELTER SUBWOOFER MIT VERSTARKER BEDIENUNGSANLEITUNG SUBWOOFER MET SPANNINGSCIRCUIT GEBRUIKSAANWIJZING SUBWOOFER CON AMPLIFICATORE E CASSA ISTRUZIONI PER LUSO ALTAVOZ DE SUBGRAVES CON CERRADO ALIMENTACION MANUAL DE INSTRUCCIONES 0 86 Kenwood Corporation B61 1319 00 00 W KW NNADDAd TONVWdS4 ONVITVLI ENGLISH IMPORTANT SAFETY INSTRUCTIONS Caution Read this page carefully to ensure safe operation Before mounting or wiring etc be sure to remove the wire from the battery minus terminal Not doing so can cause shorts or fires When extending the ignition battery or ground wires make sure to use automotive grade wires or other wires with a 0 75mm2 AWG18 or more to prevent wire deterioration and damage to the wore coating prevent short circuit never put or leave any metallic objects such as coins or metal tools inside the speaker In the event the unit generates smoke or abnormal smell im mediately switch the power OFF After this please contact your dealer or nearest service station as soon as possible POWER OFF Connect the illumination lamp equipped speakers to DC 12V negative ground
10. er cords poaa REMOTE terminal A LINE IN terminal for RCA pin jack Connecting the remote control unit Connect with the lock part of remote control jack facing EEE 9151559 down POWER SPEAKER REMOTE INPUT UNEIN L R 8 Remote control Notes If the cord is not connected properly the power indicator on the remote control unit and the illumination on the main unit do not light up If the remote control unit is not connected properly or at all the subwoofer does not output the sound Do not insert the remote control connector upside down or forcibly Otherwise malfunction may result 4 English Connecting the subwoofer to the speaker output of the center unit with built in amplifier Front speaker Rear speaker Center unit KSC SW10 Examples Connect the subwoofer to the front or rear output cords of the center unit Note Read the instruction manuals for the connected components such as the center unit as well as this instruction manual The following shows a typical connection for effective car stereo enjoyment Connect your system by referring to the example Center unit If there is no power control terminal in the center unit Front
11. oubleshooting guide Often what appears to be a malfunction is due to user error Before calling for service please consult the following table Power cannot be turned on the POWER indicator does not light No sound The fuse is blown e Check the polarity of the power cord and that the cords are not shorted then re place with a fuse with the rated capacity Re connect the cords correctly by referring to the connection example on page 5 6 The remote control cord is unplugged Plug the cord into the REMOTE terminal The power supply pin yellow of the 10 pin connection cord is not connected The power control pin blue white of the 10 pin connection cord is not connected The 10 pin connector is not plugged in com pletely The grounding pin black of the 10 pin con nection cord is not connected Connect the cord correctly by referring to the connection example on page 5 6 Check the connections of all cords then connect the cable to the battery Insert the connector all the way in Attach the grounding terminal to the metal lic section of the vehicle not a coated sur face by tightly screwing it The negative cable of the car battery is disconnected The attenuator of the center unit is set to ON Check the connections of all cords then connect the cable to the battery Switch the attenuator OFF The LEVEL control is set to the MIN position
12. p con serve resources whilst preventing detrimental effects on our health and the environment Declaration of Conformity with regard to the EMC Directive 2004 108 EC Manufacturer Kenwood Corporation 2967 3 Ishikawa machi Hachioji shi Tokyo 192 8525 Japan EU Representative s Kenwood Electronics Europe BV Amsterdamseweg 37 1422 AC UITHOORN The Netherlands For your records Record the serial number found on the back of the amplifier in the spaces designated on the warranty card and in the space provided below Refer to the model and serial numbers when ever you call upon your dealer for information or service on this product Model KSC SW10 Serial Number Parts included Outside Shape Quantity Outside Shape Quantity 10 pin connector cord Fixture A 6 198 Velcro tape Fixture B Double side adhesive for Remote control Remote control Fixture C 6m 19 ft Machine screw RCA cord M4 x 6 0 5 m 1 6 ft Tapping screw 25 x 16 English 3 Connection Caution Before wiring be sure to remove the wire from the negative terminal of the battery After completing all wiring check the correct wirings again After checking connect the wire from the negative terminal of the battery Terminals of Subwoofer lt v Z POWER SPEAKER INPUT terminal for Speak
13. partment Fix the product firmly so that it will not be moved by vibrations or impacts during driving Fixing the cord in place 4 Machine screw x 2 Fixture C 6 10 pin connector 8 Remote control Fig 2 Fixing the subwoofer Flat installation Machine screw x 4 Fixture A x 2 A Caution This portion becomes slightly hotter than other portions because it functions as the ra diator of the heat generated by the amplifier Attach the fixtures A to the speaker unit securely using the machine screws 4 Be careful so that the connected cords do not get in between the speaker unit and fixtures 1 Tapping screw 4 Drill four pilot holes for 3 6 mm screws Drill the pilot holes for 3 6 mm screws on the sheet metal section of the vehicle and attach the speaker unit to the vehicle using the tapping screws 5 Installing the remote control unit Install the remote control unit on the vehicle by the provided Velcro tape 8 Remote control Vehicle Velcro tape G Velcro tape Softer surface Harder surface Rear panel Connect the 10 pin connector cord 6 RCA cord 9 and remote control 8 to the speaker unit Fig 1 When connecting the speaker input terminal RCA cord is not necessary The cords to be connected depends on the sys tem Refer to Connection of example Fix the cords to the speaker uni
14. t with fixture 3 and fix in place with the machine screws 4 Fig 2 m Z Side installation 2 21 Holes not used Machine screw x 6 2 Fixture Bx2 Holes not used Adjust the installation height so that the speaker unit will not rattle and attach the bracket B 2 to the subwoofer using the machine screws 4 9 5 Tapping screw x 6 lt 07 Drill six pilot holes for 3 6 mm screws WaT 02 2 Fixture Bx 2 Drill the pilot holes for 3 6 mm screws on the sheet metal section of the vehicle and attach the speaker unit to the vehicle using the tapping screws 5 Caution Install the remote control unit in a position that does not come in the way of driving operations Avoid installing it in place subject to direct sunlight or direct hot wind from the heater Otherwise the product may be degraded and a fire hazard may result Remove dirt from the installation position before attaching the Velcro tape When the Velcro tape is attached on the remote control unit it cannot be accommodated in the main unit English 7 ENGLISH Operation Name of each part Remote control PHASE switch Phase select switch FREQUENCY control knob EN Cut off frequency control knob LEVEL control knob Input sensitivity control knob Power indicator Power display light Power indicator Red glows Light is OFF
Download Pdf Manuals
Related Search