JVC LST0952-001A Security Camera User Manual
Contents
1. 2 83119 31100 3XI4 102209 11110220 1 JVC 2009 Victor Company of Japan Limited LST0952 001A2. Refer to BLC AREA in the MENU SETTING separate 3 MONITOR TYPE LCD CRT Monitor Type Selector Switch Set this to LCD or CRT according to the monitor in use Default setting LCD Refer to LCD TYPE in the MENU SETTING separate Setup About Connection Cables The maximum connection distance varies with the type of cable used Be sure to turn off the power of devices before connecting cables To video Signal Cable mp To DC 12 V or AC 24 V Power Supply Video signal cable coaxial cable Connect a RG 59 75 Q coaxial cable BNC to the video signal output connecter BNC 10 Setup DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply The following table shows the connection distances when 2 core VVF vinyl insulated vinyl sheath cables are used Reference value Conductor diameter Maximum connection Maximum connection distance DC 12 V distance AC 24 V 1 0 mm AWG 18 50 m 160 ft 130 m 420 ft 1 6 mm AWG 14 140 m 450 ft 350 m 1100 ft 2 0 mm AWG 12 220 m 720 ft 550 m 1800 ft Note e If thin cables are used the resistance of the cables will be high and a significant voltage drop will occur when the camera is at its maximum power consumption Either use a thick cable with low resistance or place the power supply near to the camera and shorten the length of the cable to restrict the voltage drop at the rated
3. ratio Minimum aperture Angle of view Angle adjustment range Power supply Power current consumption Mass Ambient temperature Accessories Others 550TV lines typical 52 dB typical AGC OFF Color mode 0 05 Ix typical 50 F1 2 AGC HIGH Black and white mode 0 03 Ix typical 50 F1 2 AGC HIGH 8 75 2 8 mm to 10 5 mm F 1 2 f 2 8 mm F3 6 f210 5 mm Equivalent to F 360 f 2 8 mm 99 5 H x 73 2 V f 10 5 mm 24 4 H x 20 6 V Pan 175 Tilt 80 Rotation 100 AC 24 V 60 Hz DC 12 V TK C2201U AC 24 V 50 Hz 60 Hz DC 12 V TK C2201E 2 3 W TK C2201U 190 m TK C2201E 330 g 10 C to 50 C 14 F to 122 F Operation 0 C to 40 C 32 F to 104 F Recommended TK C2201U WARRANTY CARD x 1 INSTRUCTIONS x 3 SCREW x 2 TK C2201E INSTRUCTIONS x 5 SCREW x 2 25 Others Specifications Continued W External Dimensions Unit mm inch 46 1 13 16 2110 4 3 8 295 3 3 4 Specifications and appearance of this unit are subject to change for further improvements without prior notice 26 m Ceiling Mounting Hole Unit mm inch Others Camera Hole for cables Body 30 1 3 16 83 5 3 5 16 20 13 16 Lens shooting range Cable direction 7 7 3 8 10 7 16
4. current of camera to below 10 If voltage drop occurs during operation the performance will be unstable Do not connect the AC 24 V cable to commercial power supply If it is connected by mistake the internal circuit may be damaged Do not use the camera and make sure to send it to the nearest JVC dealer for inspection Do not connect DC 12 V and AC 24 V cables at the same time e When connecting the DC 12 V cables ensure that the polarities are correct Color of the cables red 12 V black GND e When using a DC 12 V power supply ensure that the polarities of the cable are correct e The AC24 V power supply should conform to the following U type Class 2 only E type Isolated power supply only 11 Installation Mounting the Camera Mounting the camera to the ceiling IIS When mounting the camera to the ceiling ensure to wear safety glasses to protect the eye from any falling objects t maybe mandatory to mount an embedded cover in the ceiling recessed bracket in certain areas If an embedded cover recessed bracket is required ensure it is securely mounted before installing the camera Please refer to the instruction manual for the embedded cover recessed bracket in use for details on its installation For details on the embedded cover recessed bracket please contact your JVC dealer Ceiling Embedded Cover in Ceiling recessed bracket Memo To mount the camera using an electrical bo
5. may be turned off Make use of a voltage rating within 10 for the camera s power supply voltage This unit enlarges the rotation angle to support wide range set up When the zoom of the lens is set to WIDE end and the tilt angle is set around 80 the dome cover can be visible into the image depending on the rotation angle In this case adjust the image angle if necessary page 18 The SD noise reduction function of this camera may result in afterimage of a moving subject Afterimage is more likely to occur when using the camera with DNR LEVEL set to HIGH This is not a malfunction Introduction Name of Parts Camera Interior The dome cover and inner dome are removed Refer to Mounting the camera directly to the ceiling or on the wall page 13 step 2 to 3 on the removal methods Focus Adjustment Ring se page 19 Zoom Adjustment Ring t page 19 Fall Prevention Sheet t page 13 Rotation Knob page 18 MONITOR Terminal RCA pin t page 17 6 Introduction Q Tilt Fastening Screw t page 18 Focus Adjust Gear c page 19 Q Shooting Direction Mark s page 15 rs page 18 Q Pan Center Mark c page 18 Rotation Center Mark t page 18 Function Selection Switches s page 9 B MENU Button Display the menu screen Refer to the attached manual MENU SETTING for more details about setting the menu B Status Indication Lam
6. to AUTO the mode changes automatically to black and white in dark places As the sensitivity level is increased in this case the screen may appear grainy and more white spots may appear When switching between modes the brighter area on the screen is emphasized and visibility may be reduced However this is not a malfunction When shooting an extremely bright object e g lamp the image on the screen may have white vertical tailings smear or expansion blooming may appear around it This is a characteristic of the CCD and not a malfunction When the white balance of this camera is set to ATW N or ATW W and depending on the conditions of the object the color tone may differ slightly from the actual color due to the principle of the automatic tracking white balance circuit This is not a malfunction When this camera is used under high temperatures vertical stripes may appear on the screen This is a characteristic of the CCD and not a malfunction When this camera is moved from a cold to warm place condensation may occur and the camera may not work In this case leave the camera under room temperature for about one hour before turning on the power When the power supply voltage is momentarily disrupted or drops due to lightning turning on the air conditioner or the like image distortion or noise may occur When the power supply voltage of the camera drops the input protection circuit inside the camera operates and the camera
7. wiping with a dry cloth Do not use benzene or thinner to wipe the camera Doing so may melt the surface or cause it to fog W Energy Conservation When the camera is not in use for a long time turn off the power for safety and energy conservation reasons m Copyright Protection With the exception of the user being the copyright holder or when permission Such as for duplication has been granted by the copyright holder permission is required in principle for the duplication modification or transmission of copyrighted material Unauthorized duplication modification or transmission of copyrighted material may constitute a copyright infringement and the user may be liable to compensate for any damages When using copyrighted material be sure to check the license agreement of the copyrighted material thoroughly When rights or rights holders are involved with regard to the targeted duplicating subject permission may be required for shooting or using processing it Be sure to check the licensing conditions thoroughly Introduction W Disclaimer We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product W Others When using this camera with AGC set to MID or HIGH the sensitivity increases automatically for dark images and the screen may appear grainy but this is not a malfunction If the Easy DAY NIGHT switch is turned
8. JVC FIXED DOME CAMERA TK C2201U INSTRUCTIONS TK C2201E For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No TK C2201U TK C2201E Serial No LST0952 001A Introduction Contents Introduction Contents Features Operating Precautions Name of Parts Setup Setting the Switches About Connection Cables Installation Mounting the Camera Adjustment Adjusting Image Adjusting the Auto White Balance Mounting the Dome Cover Others Specifications Introduction Thank you for purchasing this product Before use please read this INSTRUCTIONS and the information materials included to ensure proper use of this product These instructions are for TK C2201U TK C2201E Features Easy DAY NIGHT function 3D noise reduction SDNR 4 areas privacy mask Built in display mode CRT or LCD selectable How to read this manual Conventions and symbols IET Indicates operating precautions Memo Indicates reference data regarding limitations on functions usage and the like var Indicates a reference page or item Contents of this manual JVC holds the copyright to this manual Any part or all of this manual may not be reproduced without prior consent from the company Product names of other companies described in this manual are trademarks or registered tr
9. ademarks of the respective companies Symbols such as 8 and are omitted in this manual Design specifications and other contents described in this manual are subject to change for improvements without prior notice Introduction Operating Precautions Storage and Location of Use This camera has been designed for indoor use It cannot be used outdoors Do not install the camera in the following places In a place exposed to rain or moisture In a place with vapor or oil for example in a kitchen When the ambient temperature rises above or falls below the acceptable range from 10 C to 50 C In a place at which corrosive gases are emitted Near a source of radiation X rays strong radio waves or magnetism In a place subject to vibration In a place with excessive dirt Using this unit in the vicinity of the transmitting antenna of a radio or TV devices that emit strong electromagnetic waves such as a transformer or motor or wireless devices such as a transistor or mobile phone may give rise to noises in the image and changes in its color Do not install in an environment where there is cold air or near the air outlet of an air conditioner The dome cover may become foggy as a result of sudden temperature changes B Maintenance Clean the dome cover lens using a lens wiper cloth or a tissue For tough stains wipe with a neutral detergent diluted with water followed by
10. ect movement Displayed when the subject moves Keep the subject still then readjust the white balance 22 Adjustment Mounting the Dome Cover Attach the dome cover back when all settings are finished 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens Insert the inner depression of the inner dome into the protruding parts beside the fastening screw Push it in until it is locked by the catches 2 locations Catches x2 Inner depression Inner dome 23 Adjustment Mounting the Dome Cover Continued 2 Mount the dome cover and peel off the dome cover protection sheet CD Align the position marks of the same shape on the camera unit and dome cover Camera unit double track dome cover double track 2 Turn and secure the dome cover in the clockwise dirction Secure the dome cover with the two screws provided if necessary When the cover is removed again after mounting the dome cover the field angle may changed If the field angle is changed re adjust the focus and the field angle Check that the dome cover has been mounted firmly Incomplete mounting will cause the cover to drop down Mounting positions for the screws provided Dome cover m Dome cover protective sheet 24 Specifications Horizontal resolution Video S N Minimum illumination Zoom ratio Focal length Maximum aperture
11. ngle tighten and secure the tilt fastening Screw so that the field angle will not be misaligned Moving the camera beyond its adjustable range may deteriorate the performance of this camera As this camera has a wide tilt rotation range a part of this camera may appear on the screen depending on the field angle and direction Do not hold the lens unit when adjusting the camera direction Applying force on the lens unit may damage it 18 Adjustment 4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left right to adjust the image size After adjustment is complete fasten the screw with pressing it slightly toward the lens direction toward the shooting direction 5 Adjust the focus CD Hold the focus adjust gear knob shift the catch from point A to point B as illustrated in the diagram to disengage the gear To prevent the gear shaft from breaking when the gear is opened too far out from B remove the gear shaft from the bearing C in diagram In this case re insert the shaft back into the bearing C and return it to the original position before using 2 Loosen the fastening screw for the focus adjustment ring and move the ring to the left right to adjust the focus Knob Focus adjustment ring Cath B A Zoom adjustment ring Focus adjust gear 19 Adjustment Adjusting Image Continued Fine adjust the focus Press and hold the A button Foc
12. p Lights up when the power is turned on QD A Y gt P Y SET Button This allows user to select menu screens and change or confirm settings Fine Focus Adjustment 65 page 20 Auto White Balance Adjustment r page 22 Introduction Name of Parts Continued Camera Mounting Hole x 2 t page 15 Dome Cover page 13 Inner Dome page 13 o Video Signal Output Connector BNC t page 14 Q Protection Cover t page 14 Q Power Supply Cable se page 11 Wiring Hole e page 16 Q Fall Prevention Wire Mounting Screw rs page 14 Setup Setting the Switches Before mounting the camera set the function setting switches on the camera Function selection switches DIN AUTO 1 BLCOFF 2 MONTOR LCD 3 TYPE 80096 4 SEE INSTRUCTION MANUAL DIP Switch Settings Chart 1 D N AUTO OFF Easy Day amp Night Switch Set this to AUTO when shooting a subject with continually changing brightness day night The image switches to color when the subject is bright and black and white when it is dark The image is set to color at all times when OFF is selected Default setting AUTO 2 BLC OFF ON Backlight Compensation Selector Switch Set this to ON when shooting in backlight The subject becomes easier to see as brightness is adjusted according to the photometry area set in BLC AREA of the menu Default setting OFF
13. tton 2 Select WHITE BALANCE with the A V button and AWC with the lt gt button then press the SET button Zoom in to fill the screen with white Place a white object at the center of the screen under the same lighting condition as the subject to be shot and zoom in to fill the screen with white 4 Press the SET button Auto white balance adjustment begins During operation AWC OPERATION is displayed on the screen 5 Adjustment is complete When the appropriate white balance is acquired AWC OK is displayed SET button MENU button P AWC SET P AWC SET AI R GAIN 160 R GAIN 160 TN B GAIN 160 B GAIN 160 5 6 9 SET Or AV lt gt AWC OPERATION W Error display Y button AWC OPERATION AWC OK during operation adjustment completed If auto white balance adjustment is not successful the following messages will appear on the monitor AWC ERROR NG Subject error Displayed when there is not enough white color on the subject or the color temperature is not suitable Fill the screen with a white object thoroughly and adjust the white balance again AWC ERROR LOW LIGHT Insufficient Illumination Displayed when the light is low Increase the illumination then readjust the white balance AWC ERROR HIGH LIGHT Excessive Illumination Displayed when the light is too bright Decrease the illumination then readjust the white balance e AWC ERROR TIME OVER Subj
14. us adjust mode will be activated and FOCUS ADJUST MODE is displayed on the monitor screen The contours are emphasized as the iris opens and the depth of field becomes shallow e After adjustment press W lt p SET or MENU to exit focus adjust mode The mode is also automatically deactivated after about 30 seconds Memo During the focus adjust mode the electronic shutter will function automatically As a result the screen will appear grainy This is not a malfunction 2 Shoot the subject Return the catch to A in the diagram and then rotate the knob to adjust the focus to the optimum position Rotate the focus adjust gear knob one base pitch in the direction of the arrow in the diagram to correct the focus shift when mounting the dome cover 5 Peel off the protection sheet temporarily and cover the dome cover to check the focus After checking paste the protection sheet back on the dome cover One base pitch 20 Adjustment 7 Tighten the fastening screw of the focus adjustment ring Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram and tighten the fastening screw of the focus adjustment ring Focus adjustment ring 21 Adjustment Adjusting the Auto White Balance Each light source has its own color temperature Therefore when the main light source lighting the subject is changed adjust the white balance again 1 Press the MENU bu
15. ut both ends of the extraction hole for the cable with a nipper ang break off the excess material using tools such as long nose pliers 2 Pull out the cable from the extraction hole and mount it to the ceiling or wall TA 16 Adjustment Adjusting Image After mounting the camera adjust the images while looking at the actual image Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction 1 Mount the monitor Connect the monitor terminal of this camera to a test monitor to adjust the camera s shooting direction image and focus 2 Turn on the camera Monitor terminal 75 Q terminal Monitor 17 Adjustment Adjusting Image Continued 3 Adjust the shooting direction of the camera Adjust the camera for pan tilt and rotation and face the camera towards the subject Pan 41755 RN Tilt fastening screw Rotation x 100 Rotation knob x 2 Memo Rotate both pan 175 and rotation 100 from the positions aligned with the camera s shooting direction mark pan center mark and rotation center mark Be sure to hold the rotation knob and adjust the rotation without holding the lens unit Loosen the tilt fastening screw before performing tilt adjustment After adjusting the field a
16. ver the connectors This will isolate and protect the metallic parts of the connectors from the ceiling structures 3 Connect the power supply cable rs page 11 4 Wrap insulation tapes around the connecting parts of the power supply cables Memo Wrapping insulation tapes will improve future work conditions as well as reduce penetration by noise and other objects Power cable Fall prevention wire Solder or caulk L 4 Insulating tape Protection cover Coaxial cable 14 Installation W Mounting 1 Align 0 with the shooting direction and mount the camera onto the ceiling IET Mounting screw not included e The diameter of the attachment hole is 4 5 mm 3 16 inch Do not use flathead screws e When using an impact screwdriver do not tighten the screws fully Tighten using your hand instead Failure to do so may damage the outer case W Adjusting images After mounting is completed adjust the images while checking the actual image Adjusting Image r page 17 15 Installation Mounting the Camera Continued Mount by allowing the cable to exit from the side When mounting the camera to the ceiling or a wall it is possible to guide the cable from the side without opening any holes The basic mounting method is identical to steps in Mounting the camera directly to the ceiling or on the wall page 13 1 C
17. x please contact the nearest JVC dealer 12 Installation Mounting the camera directly to the ceiling or on the wall When mounting to a wall replace areas indicated as ceiling in the procedures by wall W Setup enn a hole in the ceiling 30 mm 1 1 8 inches and draw the I prevention wire power supply cable and coaxial cable out fen the ceiling fall prevention wire is not included 1 Bs SALUS L Power cable Fall prevention wire not supplied Coaxial cable 7 Approx 100 mm 3 7 8 inches 2 Remove the dome cover As illustrated in the diagram hold the dome cover such that the position alignment mark comes between the thumb and index finger and turn the cover in the counter clockwise direction to remove the cover Refer to page 24 for more details about position alignment mark 3 Remove the inner dome from the catches two locations The inner dome can be easily removed by turning it about 45 degree and grip from both sides near the catches as illustrated in the diagram Position alignment mark Catches x 2 4 Set the switches for video images rs page 9 13 Installation Mounting the Camera Continued B Connection 1 Attach the fall prevention wire from the ceiling to the camera fall prevention wire is not included 2 Connect the coaxial cable t page 10 Lower the protection cover and connect the connectors Upon connecting restore the protection cover to co
Download Pdf Manuals
Related Search