Home

JVC AV32R25EK CRT Television User Manual

1. Specifications Model Item AV32R25EK AV32R250EK AV28R25EK AV28R250EK Broadcasting systems CCIR I Colour systems PAL The EXT terminals also support the NTSC 3 58 4 43 MHz system Channels and frequencies E21 E69 Sound multiplex systems NICAM I system Teletext systems FLOF Fastext WST World Standard Text Power requirements 220 240 V AC 50 Hz Power consumption Maximum 200 W Average 127 W Maximum 200 W Average 125 W Standby 3 W Standby 3 W Picture tube size Viewable area 76 cm measured Viewable area 66 cm measured diagonally diagonally Audio output Rated Power output 10 W 10 W 10 W 18 W woofer Speakers 13 cm x 6 5 cm oval x 2 16 cm x 4 cm oval x 1 13 cm round woofer x1 EXT 1 terminal Euroconnector 21 pin SCART e Video input Audio L R inputs and RGB inputs are available TV broadcast outputs Video and Audio L R are available EXT 2 terminal Euroconnector 21 pin SCART e Video input S VIDEO Y C input and Audio L R inputs are available e Video and Audio L R outputs are available T V LINK functions are available EXT 3 terminal Euroconnector 21 pin SCART e Video input S VIDEO Y C input and Audio L R inputs are available EXT 4 terminal RCA connectors x 3 S VIDEO connector x 1 e Video input S VIDEO Y C input and Audio L R inputs are available AUDIO OUT terminal
2. RCA connectors x 2 e Variable audio L R outputs are available e Variable out 0 1 Vrms low impedance SURROUND REAR terminal SPEAKER terminals for external surround speakers e Surround rear sounds are output to the speakers e For impedance 8 ohm speakers only e Rated power output 7 5 W 7 5 W Headphone jack Stereo mini jack 3 5 mm in diameter Dimensions W x Hx D 946 mm x 562 mm x 551 mm 854 mm x 507 5 mm x 493 5 mm Weight 56 0 kg 43 0 kg Accessories Remote control unit x 1 RM C60 Gray or RM C52 Brack is supplied AAA RO3 dry cell battery x 2 A basic model number The actual model number may have characters added such as S for silver showing the colour of the TV set We may change the design and specifications without notice Pictures displayed on the screen using this TV s ZOOM functions should not be shown for any commercial or demonstration purpose in public places cafes hotels etc without the consent of the owners of copyright of the original picture sources as this would be an infringement of copyright 2003 VICTOR COMPANY OF JAPAN LIMITED LCT1152 001D U D 0403 T CR JMUK MA0S7HBZAVW MANSTUZEAV MASTHBCAV MASZUZEAV Colour Television AV32R25EK AV28R25EK AV32R250EK AV28R250EK INSTRUCTIONS f My T_i 7 f INI E F meet Contents Setting up yourTV 5 TV buttons and functions 10 Remote control bu
3. E TINT You can select one of three TINT modes three kinds of picture settings to adjust the picture settings automatically COOL A cool white colour base with a boost in the colour and contrast levels that creates a more vivid picture WARM A warm orange red colour base that creates the appropriate colour and contrast levels for watching films NORMAL A normal white colour base with normal colour and contrast levels Picture Adjustment You can change the picture settings of each TINT mode as you like CONTRAST You can adjust the picture contrast lt lower gt higher BRIGHT You can adjust the picture brightness lt darker gt brighter SHARP You can adjust the picture sharpness lt softer gt sharper COLOUR You can adjust the picture colour lt lighter gt deeper Using the TV s menu HUE You can adjust the picture tint lt reddish gt greenish e You can change the HUE setting picture hue only when the colour system is NTSC 3 58 or NTSC 4 43 See Specifications on the back cover To return to the default settings in each TINT mode Press the blue button This returns the picture settings in the TINT mode you have chosen to the default settings and stores them in the TINT mode 19 20 Using the TV s menu PICTURE FEATURES O AUTO VNR COLOUR SYSTEM 4 3 AUTO ASPECT PICTURE TILT m AUTO VNR VNR Stands for vide
4. CHILD LOCK appears You cannot view the TV channel 3 Press the OK button The Sub menu of CHILD LOCK appears CHILD LOCK 2 Press the Information button to display ID NO ID No input screen 3 Press the number buttons to enter the ID number The lock is temporarily released so you can view the TV channel Using the TV s menu If you have forgotten the ID epee n INSTALL Perform step 1 of To set the CHILD LOCK function After confirming the ID number press the TV button to exit the menu O LANGUAGE AUTO PROGRAM EDIT MANUAL e Even if you reset the lock temporarily it does not mean that the CHILD NU LOCK function set for the TV channel 0x0 is cancelled The next time anyone tries to view the TV channel it will be E LANGUAGE locked again You can choose the language you want to use When you want to cancel the CHILD for the on screen display from the language LOCK function you must perform the list in a menu operation To set the CHILD LOCK function again 1 Choose LANGUAGE then press To stop it being easy to choose the the OK button programme number PR of a locked A sub menu of the LANGUAGE function TV channel the programme number appears PR has been set so that it cannot be chosen by the W A buttons or the buttons of the TV EnH To stop it being easy to reset the lock NEDERLANDS ID NO ID No input screen is set NORSK so that it c
5. e Ifthe picture is tilted correct it See PICTURE TILT not AV28R25EK AV28R250EK on page 21 Adjust the volume Press the lt gt buttons to adjust the volume The volume indicator appears and the volume changes as you press the buttons PR in the PR LIST You cannot use the W A buttons to choose a Programme number PR which has the CHILD LOCK set Even if you try to choose a programme number PR with the CHILD LOCK set the amp mark will appear and you cannot watch the TV channel To watch the TV channel see CHILD LOCK on page 28 If the picture is tilted correct it See PICTURE TILT not AV28R25EK AV28R250EK on page 21 To return to a TV channel Press the TV button the V A buttons or the number buttons To use the programme number PR 0 AV When the TV and VCR are connected only by the aerial cable choosing the programme number PR 0 AV allows you to view images from the VCR Set the VCR RF channel to the programme number PR 0 AV manually For details see EDIT MANUAL on page 30 Pressing the O CAV button changes the choice as follows TV mode EXT modes E PRO eine EXT 1 EXT 2 a ic Zoe Li e The VCR sends its playback image along the aerial cable as an RF radio frequency signal e Also see your VCR instruction manual ZOOM function You can change the sc
6. PR changes and the picture of the TV channel stored in the programme number PR appears on the screen Press the red button to start the ID function Press the W A buttons to choose the first character of a channel name ID you want to give the TV channel Press the blue button to display the ID LIST channel name list 5 Press the W A buttons to choose the channel name ID To cancel the ID function Press the Information button 6 Press the OK button to give a channel name ID to a TV channel e You can give your own unique channel name ID to the TV channel When you have finished step 3 do not go to step 4 Press the lt P gt buttons to move the cursor and press the W A buttons to choose each character of the channel name ID Then press the OK button to register the channel name ID to the TV channel INSERT Preparation You need to find the CH number for the TV channel Find the CH number from the CH NUMBER table on page 34 based on the channel number of the TV channel 1 Press the V A buttons to choose a programme number PR for which you will register a new TV channel 2 Press the green button and start the INSERT function To cancel the INSERT function Press the Information button Using the TV s menu 3 Press the number buttons to enter MANUAL the remaining CH number 1 Press the W A buttons to choose a The TV shifts to r
7. TV For details see your VCR instruction manual E TV auto power on VCR image view When the VCR starts playing the TV automatically turns on and the images from the EXT 2 terminal appear on the screen When the VCR menu is operated the TV automatically turns on and the images from the EXT 2 terminal appear on the screen This function does not happen if your TV s main power is turned off Set your TV s main power to on standby mode 10 TV buttons and functions Refer to the pages in brackets for details Remote control sensor 2 Power lamp 6 10 G Main power button 6 10 Headphone jack mini jack 39 P V A buttons buttons 11 lt 1 Volume button 10 EXT 4 terminal 25 39 Turn the main power on Press the Main power button on the TV The power lamp lights red and your TV is in the standby mode If the power lamp lights green the TV is already on To turn the main power off Press the main power button again The power lamp goes off Caution The main power button on the TV does not fully isolate the TV from the AC supply If you are not going to use the TV for a long period of time be sure to disconnect the AC plug from the AC socket Turn the TV on from standby mode Pre
8. To display DIGITAL SURROUND on the MENU disconnect the headphone from the TV e The display appearing at the bottom of a menu shows the buttons on the remote control you can use when you operate a chosen function lt gt TV button OK button When a menu is displayed on the screen the ZOOM mode may be automatically changed to the FULL mode This is not a malfunction When the menu disappears the ZOOM mode will return to the previously set ZOOM mode Press the W A buttons to choose a menu title and press the OK button The menu appears To return to the previous menu Press the information button To exit a menu instantly Press the TV button Press the W A buttons to choose a function For details of the functions in the menus see the following pages Press the lt gt buttons to choose the setting of that function If you want to operate a function which appears only with its name follow the descriptions of that function on the following pages e The display appearing at the bottom of a menu shows you the button on the remote control that you can use when you operate a chosen function 5 Press the OK button to complete the setting The menu disappears e When watching the television with the NTSC system the menus are displayed at about half of their normal vertical size PICTURE SETTING PICTURE SETTING OWT INT NORMAL CONTRAST E RESET
9. You can view two types of teletext broadcasts on the TV FLOF Fastext and WST 1 Choose a TV channel with a teletext broadcast 2 Set the VCR amp DVD switch to the Text position vcr amp pvp 3 Press E Text button to display the teletext Pressing Text button changes the mode as follows 2 TV mode TEXT TEXT Text mode 4 Choose a teletext page by pressing the V A buttons number buttons or colour buttons To return to the TV mode Press the TV button or amp Text button e Ifyou have trouble receiving teletext broadcasts consult your local dealer or the teletext station In Text mode the ZOOM mode is fixed to FULL e You cannot operate menus when viewing a teletext programme Using the List Mode You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons To store the page numbers 1 Press the MODE button to go into the List mode The page numbers you have stored are displayed at the bottom of the screen 2 Press a colour button to choose a position Then press the number buttons to enter the page number aAaoOo gt p gt ooO OQO O00 3 Press and hold down the STORE button The four page numbers blink white to show that they are stored in memory To call up a stored page 1 Press the MODE button to enter the List mode 2 Press a colour butt
10. e You cannot choose NTSC 3 58 or NTSC 4 43 for programme number PR 0 AV to PR 99 Using the TV s menu E 4 3 AUTO ASPECT A a A O You can choose one of three ZOOM modes SOUND SETTING REGULAR PANORAMIC or 14 9 ZOOM as the ZOOM mode for the normal picture 4 3 aspect ratio O TREBLE m 1 Choose 4 3 AUTO ASPECT then BALANCE I SPEAKER ON press the OK button OIPANORAMIC Oo amp REO EAR in E STEREO Ie ll When you are viewing a bilingual broadcast D programme you can choose the sound from QQ Bilingual I Sub I or Bilingual II Sub Il If you have poor reception on a stereo 2 Press the W A buttons to choose a broadcast you can change from stereo to ZOOM mode mono sound so that you can hear the broadcast more clearly and easily m PICTURE TILT CO Stereo sound not AV28R25EK AV28R250EK Sometimes the Earth s own magnetic field may make the picture tilt If this happens you can correct the picture tilt 1 Choose PICTURE TILT Then press Bilingual I sub I O mono sound l I Bilingual II sub II The sound mode you can choose differs the OK button depending on the TV programme PICTURE TILT This function does not work in the EXT modes And this function does not appear in the SOUND SETTING menu E Sound Adjustment You can adjust the sound to your liking BASS 2 Press the W A buttons until the You can adjust the low tone of the sound picture becomes le
11. to try to solve the problem Have the TV and aerial been connected properly due to a TV failure When the picture Has the aerial cable been damaged disappears from the screen the unnatural Is the aerial pointing in the right colours will also disappear direction Is the aerial itself faulty E Poor sound e Have you adjusted BASS or TREBLE properly If not follow the description Sound Adjustment on page 21 e When TV channel reception is poor it can be hard to hear stereo or bilingual sound In this case follow the description STEREO I II on page 21 to hear the sound more easily by changing it to a mono sound E If the TV does not respond to the remote control e Have the batteries of the remote control worn out Follow the description Putting the batteries into the Remote control on page 6 and replace them with new batteries e Have you attempted to use the remote control from the sides or rear of the TV or from more than seven metres away from the TV Use the remote control in the front of your TV or from less than seven metres away e When you are viewing a teletext programme you cannot operate the menus Press the TV button to return to the ordinary TV programme and then try operating the menus Ifthe TV will not respond suddenly press the main power button on the TV and turn off the main power Press the main power button again to turn on the TV If the TV returns
12. LIST To erase a name assigned to the EXT terminal Choose a blank space 4 Press the OK button to complete the setting DUBBING You can choose a signal source to be output from the EXT 2 terminal You can do this with the output signal of the device connected to another EXT terminal or the picture and sound from a TV channel you are currently viewing 1 Press the lt gt buttons to choose the arrow from the menu 2 Press the V A buttons to choose an EXT terminal or TV Then press the OK button EXT SETTING EXT 1 EXT 3 l DUBBING EXT 2 EXT 4 OOOO 2 TV amp amp The arrow in the menu represents a signal flow The left side of the arrow shows a signal source output from the EXT 2 terminal EXT 1 EXT 3 EXT 4 The output signal of the device connected to an EXT terminal passes through the TV and is output from the EXT 2 terminal TV The picture and sound of the TV channel you are currently viewing are output from the EXT 2 terminal During dubbing you cannot turn off the TV Turning off the TV also turns off the output from the EXT 2 terminal When you choose an EXT terminal as an output you can view a TV programme or a picture from the other EXT terminal while dubbing the picture from a device connected to the EXT terminal onto a VCR connected to the EXT 2 terminal The RGB signals from TV games cannot be output Teletext programmes cannot be output Us
13. area of the screen Cancel You can search for a teletext page while watching TV 1 Press the number button to enter a page number or press a colour button The TV searches for a teletext page 2 Press the CANCEL button The TV programme appears When the TV finds the teletext page its page number appears in the upper left of the screen 3 Press the CANCEL button to return to a teletext page when the page number is on the screen The TV mode cannot be resumed by pressing the CANCEL button To return to the TV mode press TV 17 18 Using the TV s menu This TV has a number of functions you can operate using menus To use all your TV s functions you need to understand the basic menu operating techniques fully CQ Blue button apg TV PIA OK I gt NU via SS lt Basic operation 1 Press the OK button to display the MENU main menu When the headphones are not connected to the TV O PIcTuRE SETTING PICTURE FEATURES SOUND SETTING DIGITAL SURROUND EXT SETTING FEATURES INSTALL DEMO amp When the headphones are connected to the TV O PICTURE SETTING PICTURE FEATURES SOUND SETTING HEADPHONE SURROUND EXT SETTING FEATURES INSTALL DEMO e You cannot choose DIGITAL SURROUND and HEADPHONE SURROUND on the MENU main menu at the same time To display HEADPHONE SURROUND on the MENU connect the headphone to the TV
14. from more than one transmitter for example different ITV regions In this case each TV channel could be set twice If this happens the first set of channels will have the stronger signal If you want to delete the second set of channels you will have to do it manually see page 33 If you have had any problems setting up your new TV please call the JVC Helpline at 0870 330 5000 Enjoy your new JVC TV T V LINK functions When you have a T V LINK compatible VCR connected to the EXT 2 Terminal on the TV it is easier to set up the VCR and to view videos T V LINK uses the following features To use T V LINK functions A T V LINK compatible VCR means a JVC video cassette recorder with the T V LINK logo or with one of the following logos However these VCRs may support some or all of the features described earlier For details see your VCR instruction manual Q LINK a trademark of Panasonic Corporation Data Logic a trademark of Metz Corporation Easy Link a trademark of Phillips Corporation Megalogic a trademark of Grundig Corporation SMARTLINK a trademark of Sony Corporation Pre set download The VCR will automatically download the registered data on the TV channels from the TV This means you do not need to set up the program channels on your VCR manually The preset download function automatically begins when the initial setting is complete or whenever you carry out
15. input setting Press the yellow button and turn off S S VIDEO input mark The regular video signal composite signal pictures are resumed The EXT 1 terminal does not support S VIDEO signal Y C signal and you cannot set S amp S VIDEO input in the EXT 1 terminal Setting S S VIDEO input changes the head character from E to S When an EXT terminal receives a normal video signal E1 E2 E3 or E4 appears on the display This changes to S2 S3 or S4 when it receives an S VIDEO signal e Even a device which can output an S VIDEO signal Y C signal may output a regular video signal composite signal depending on the device setting If a picture cannot appear because the S amp S VIDEO input setting has been made read the device instruction manual carefully again to check for the device settings E LIST You can store a name for each of the devices connected to each EXT terminal Giving a name to an EXT terminal makes the EXT terminal number appear on the screen together with its name 1 Choose an EXT terminal 2 Press the blue button to display the name list LIST EXT SETTING EXT 1 i EXT 3 i DUBBING EXT sz 3 Press the V A buttons to choose a name Then press the OK button The LIST disappears and the name is assigned to the EXT terminal e You cannot choose an EXT terminal name that is not on the name list
16. leave the TV SPEAKER setting to L C R If you don t a normal sound Then press the gt button The sub menu of the PRO LOGIC 3D PHONIC function appears PRO LOGIC 3D PHONIC will not come from the TV speakers If the TV SPEAKER is not set to L C R press the W A buttons to choose TV SPEAKER and press the lt P buttons to choose L C R again DOLBY PRO LOGIC You can enjoy Dolby Surround Pro Logic sound if you add surround speakers Before using the DOLBY PRO LOGIC function first connect the surround speakers to the TV then set the items in the DOLBY PRO LOGIC function properly For details see Connecting speakers or an amplifier on page 40 z Choose DOLBY PRO LOGIC Then press OK button To cancel the DOLBY PRO LOGIC MODE NORMAL OLEVEL C E TV SPEAKER L C R C C T C C 2 Press the V A buttons to choose an item Then press the lt gt buttons to change the setting MODE The PRO LOGIC 3D PHONIC function has three modes NORMAL CINEMA SPORT and MUSIC You can choose function and set a mode as you like Press the W A buttons to choose LEVEL SURROUND OFF The DOLBY PRO LOGIC function will not work correctly unless you connect extra surround speakers The DOLBY PRO LOGIC function is only available for Dolby Surround encoded programmes e Even if you do not have surround speakers the PRO LOGIC 3D PHONIC function lets you enjoy the atmosphere of Dolby Surround Pro Lo
17. operations Downloading data to a VCR You can send the latest programme numbers PR data to a VCR with the T V LINK function e You can only do this when a T V LINK compatible VCR is connected to the EXT 2 terminal This only works when the T V LINK menu is being displayed T V LINK DOWNLOAD TV VCR ow koa 1 Turn onthe VCR 2 Press the OK button The data transmission begins T V LINK TV VCR The T V LINK menu disappears once the data transmission ends When the T V LINK menu changes over to another menu The TV has finished its menu This new menu is operated from the VCR See the VCR instruction manual for what to do next If FEATURE NOT AVAILABLE appears at the T V LINK menu check the following three items Then press the OK button to retry data transmission e Has a T V LINK compatible VCR been connected to the EXT 2 terminal e Has the VCR power been turned on e Does the SCART cable that connects the EXT 2 terminal to the T V LINK compatible VCR have all its proper connections Using the DECODER EXT 2 function If you have a decoder connected to a T V LINK compatible VCR which in turn is connected to the EXT 2 terminal use the DECODER EXT 2 function to unscramble the scrambled TV channels 1 Turn on the decoder power 2 Display the scrambled TV channel on the TV Even if the decoder is working a scrambled picture appears 3 Press the OK butt
18. reception If so the BLUE BACK voltage wire please contact your local function will be activated the entire dealer screen becomes blue and the sound is Ifthe TV suffers interference from signals muted If you still want to view the TV reflecting from mountains or buildings channel follow the description BLUE double pictures ghosting will occur Try BACK on page 28 to try to change the to change the aerial s direction or replace BLUE BACK function setting to OFF it with one with better directionality e Have you connected headphones to the e Are your COLOUR SYSTEM settings TV correct Follow the description Connecting headphones to the TV turns COLOUR SYSTEM on page 20 to try off the TV speakers to solve the trouble e Have you set the SPEAKER function to e Have the COLOUR and BRIGHT settings OFF Follow the description been adjusted properly Follow the SPEAKER on page 22 to check the description Picture Adjustment on SPEAKER function setting page 19 to try to adjust them properly e Videotaping teletext is not recommended because it may not record correctly e When a white and bright still image such as a white dress is displayed on the screen the white part may look as if it is coloured This is unavoidable due to the nature of the picture tube itself and not E Poor picture e If noise snow totally block out the picture there may be a problem with the aerial or aerial cable Check the following
19. rest assured that this static discharge is not harmful 43
20. speakers so that you can listen to spoken dialogues more clearly and easily For details see Using the TV speakers as the centre speakers for the PRO LOGIC 3D PHONIC function on page 37 You cannot cut the sound from the front speaker even if you connect a headphone to the TV Additional preparation E External surround speakers You can connect external surround speakers to the TV so that you can use the DOLBY PRO LOGIC on page 23 Before using the DOLBY PRO LOGIC function however follow the description Setting the DOLBY PRO LOGIC function on page 37 Amplifier Front speakers magnetic shielded type Surround speakers impedance 8 ohm type N w 2 oR AUDIO OUT R L 2 SURROUND REAR A N Approx Ki 45degrees Removing and Fitting the Woofer Unit E Removing the woofer unit The woofer unit may be removed as necessary Remove the connector while pushing the connector lever on the WOOFER terminal lift the woofer and remove it E Fitting the woofer unit Fit the woofer unit in the reverse order to that described in Removing the woofer unit Align the projection on the base of the woofer unit with the hole in the top of the TV and insert the connector into the WOOFER terminal E Cautions when fitting the woofer unit e Check that the woofer unit is fitted correctly on the top of the TV e Do not use excessive f
21. surround speakers Set TV SPEAKER to L C R When you are connecting both an audio system and surround speakers Set TV SPEAKER to CENTRE All the TV speakers act as a centre speaker However almost no sound is emitted from the woofer Press the W A buttons to choose TEST MODE Then press the lt gt buttons to choose ON Test signals are output alternately from each of the speakers To make sounds come from the front speakers of the audio system Slowly turn up the amplifier volume until the volume from the front speaker is roughly equal to that from the TV speakers or surround speakers Press the lt gt buttons to adjust the sound volumes of the speakers so that you can listen to the sounds at the same volume when you are sitting where you would normally sit to watch the TV LEFT CENTRE RIGHT SURROUND LEFT and RIGHT stands for the left and right of the front speakers CENTRE refers to the centre speaker and SURROUND refers to surround speakers 7 Press the OK button to complete the settings The menu disappears e For details about listening positions see Connecting speakers or an amplifier on page 40 e When you use both an audio system and the TV speakers and they are not matched in sound quality you can change over the TV SPEAKER setting to OFF to cut the TV speakers Additional preparation Connecting external equipment Connect the equipment to the TV making VCR composite
22. terminal You can choose between an S VIDEO signal Y C signal and a regular video signal composite signal For details of how to operate the equipment see S S VIDEO input on page 25 E T V LINK compatible VCR Be sure to connect the T V LINK compatible VCR to the EXT 2 terminal If not the T V LINK function will not work properly e When connecting a T V LINK compatible VCR to the EXT 2 terminal be sure to connect the decoder to the VCR If not the T V LINK function may not work properly After you have stored TV channels in the programme numbers PR list set the DECODER EXT 2 function for the programme number PR to ON to unscramble a scrambled TV channel For details see Using the DECODER EXT 2 function on page 35 E Connecting headphones Connect the headphones with a stereo mini jack 3 5 mm diameter to the headphone jack at the TV front panel e When you connect the headphones the TV speakers go off E Video or sound signal output from the EXT 2 terminal You can change over the output of the video sound signal from the EXT 2 terminal This is useful when you want to dub the video sound from another device onto the VCR connected to the EXT 2 terminal For details on how to do this see DUBBING on page 26 E TV output from the EXT 1 terminal The video sound signal of a TV channel you are viewing is always output from the EXT 1 terminal e Changing over a programme number PR
23. the AUTO PROGRAM or EDIT MANUAL functions You can also carry out this function using your VCR controls When FEATURE NOT AVAILABLE is displayed If FEATURE NOT AVAILABLE is displayed the download was not performed correctly Before trying to download again check that e the VCR power is turned on e the VCR is T V LINK compatible e the VCR is connected to the EXT 2 terminal e the SCART cable is fully wired Setting up your TV E Direct Rec What You See Is What You Record You can easily record to VCR the images that you are watching on the TV For details read the manual for your VCR Use your VCR controls VCR IS RECORDING is displayed In the following situations the VCR will stop recording if the TV is turned off if the TV channel or input is changed or if the menu is displayed on the TV e when recording images from an external device connected to the TV for example a camcorder e when recording a TV channel after it has been unscrambled on a decoder e when recording a TV channel by using the TV s output because the VCR s own tuner cannot properly receive that channel You cannot carry out Direct Rec using your TV s control Generally the VCR cannot record a TV channel that it cannot receive properly on its own tuner even if you can view that TV channel on the TV However some VCRs can record a TV channel by using the TV s output if that channel can be viewed on the
24. want to use the INSERT function on page 32 find the CH number corresponding to the channel number of the TV channel from this table If you want to know a particular TV channel s channel menu look in TV listings magazines or contact the broadcaster CH Channel CH Channel CH 21 E21 CH 46 E46 CH 22 E22 CH 47 E47 CH 23 E23 CH 48 E48 CH 24 E24 CH 49 E49 CH 25 E25 CH 50 E50 CH 26 E26 CH 51 E51 CH 27 E27 CH 52 E52 CH 28 E28 CH 53 E53 CH 29 E29 CH 54 E54 CH 30 E30 CH 55 E55 CH 31 E31 CH 56 E56 CH 32 E32 CH 57 E57 CH 33 E33 CH 58 E58 CH 34 E34 CH 59 E59 CH 35 E35 CH 60 E60 CH 36 E36 CH 61 E61 CH 37 E37 CH 62 E62 CH 38 E38 CH 63 E63 CH 39 E39 CH 64 E64 CH 40 E40 CH 65 E65 CH 41 E41 CH 66 E66 CH 42 E42 CH 67 E67 CH 43 E43 CH 68 E68 CH 44 E44 CH 69 E69 CH 45 E45 The DEMO function automatically demonstrates some of the TV functions Choose ON or OFF Then press the OK button The DEMO function is set to ON and the demonstration will start To stop the demonstration Press one of the buttons on the remote control When the DEMO function is set to ON Each time the TV is turned on the demonstration starts automatically If you do not want that to happen cancel the DEMO function 1 Display the DEMO menu again 2 Press the W A buttons to choose OFF 3 Press the OK button to cancel the DEMO function Additional menu
25. AUTO PROGRAM function Press the TV button AUTO PROGRAM CH 28 20 CIE After the TV channels have been registered in the programme numbers PR the EDIT menu appears e Ifyou want to you can now edit the programme numbers PR using the EDIT MANUAL function For details see EDIT MANUAL on page 30 e Ifyou do not want to edit programme numbers PR go to the next step If you do not have a T V LINK compatible VCR connected Press the TV button to exit the T V LINK menu The T V LINK menu disappears If you have a T V LINK compatible VCR connected to the EXT 2 terminal Follow the operating procedure Downloading data to a VCR on page 35 to transmit the programme number PR data Setting up your TV Now the initial settings are complete and you can watch the TV BBCI BBC2 ITV Channel 4 and Channel 5 are automatically set to programme numbers PR 1 to PR 5 SKY 1 is set to programme number PR 6 but no TV channel name ID is set If the TV doesn t receive one of these TV channels that programme number PR will not be set e Ifa TV channel you want to view is not set to a programme number PR you can set it using the MANUAL function For details see EDIT MANUAL on page 30 The AUTO PROGRAM function does not set the programme number PR 0 AV for your video cassette recorder You will need to set this using the MANUAL function e In some areas you may get TV reception
26. LD LOCK function to lock out the TV channel Even when a child chooses a programme number PR for a locked TV channel the screen will change to blue and display CHILD LOCK so the TV channel cannot be viewed Unless you enter a pre set ID number by a special operation the lock cannot be released and the child cannot view the TV channel To set the CHILD LOCK function 1 Choose CHILD LOCK then press the 0 CAV button SET ID NO ID number setting screen appears SET ID NO On ooo Ow Re 2 Set the ID number to your liking 1 Press the V A buttons to choose a number 2 Press the lt P gt buttons to move the cursor 4 Press the W A buttons to choose a TV channel Every time you press the W A buttons the Programme number PR changes and the picture of the TV channel registered in the Programme number PR is displayed on the screen 5 Press the blue button and set the CHILD LOCK function Then press the OK button CHILD LOCK appears and the TV channel is locked To reset the CHILD LOCK function Press the blue button again CHILD LOCK disappears To disable easy resetting of the CHILD LOCK function the menu disappears if you choose the CHILD LOCK function and press the OK button To view a locked TV channel 1 Choose a programme number PR in which a TV channel locked with the number buttons or PR LIST The screen changes to blue and the
27. ONIC function ASPECT on page 21 will be activated when no headphones are a connected For details see PRO LOGIC a Adjusting the visible area of the 3D PHONIC Dolby Pro Logic 3D picture PHONIC on page 22 If subtitles or the top or bottom of the picture are cut off you can adjust the visible area of the picture manually The 3D HEADPHONE function will be activated when headphones are connected For details see 3D 1 Press the ZOOM button HEADPHONE on page 24 The ZOOM menu appears 2 Press the OK button to display the ZOOM mode indicator The indicator appears 16 9 zoon S Displaying the current time You can display the current time on the screen Press the Information button to display the current time Pressing the Information button changes the display as follows Remote control buttons and functions Operating a JVC brand VCR or DVD player These buttons will operate a JVC brand VCR or DVD player Pressing a button that looks the same as the device s original remote control button has the same effect as the original remote control 1 Set the VCR amp DVD switch to the PR LIST ww 1 OXO AA o 12 00 Current time y No indication This TV uses teletext data to set the time If the TV has not received a TV channel that has teletext programmes since it was turned on the time display is blank To se
28. ails see EDIT MANUAL on page 30 e Ifyou do not need to use the EDIT MANUAL function go to the next step 3 Press the OK button to display the T V LINK menu T V LINK DOWNLOAD TV VCR mo 4 If you do not have a T V LINK compatible VCR connected Press the TV button to leave the T V LINK menu The T V LINK menu disappears and all the settings are completed If you have a T V LINK compatible VCR connected to the EXT 2 terminal See Downloading data to a VCR on page 35 to transmit the programme number PR data to the VCR e Ifa TV channel you want to view is not set to a programme number PR set it manually using the MANUAL function For details see EDIT MANUAL on page 30 e The AUTO PROGRAM function does not set the programme number PR 0 AV for your video cassette recorder You will need to set this using the manual function In some areas you may get TV reception from more than one transmitter for example different ITV regions In this case each TV channel could be set twice If this happens the first set of channels will have the stronger signal If you want to delete the second set of channels you will have to do it manually see page 33 E EDIT MANUAL The EDIT MANUAL functions are divided into two types e editing the current programme numbers PR EDIT functions and e manually storing a TV channel you want to view a programme number PR MANUAL f
29. also changes over the TV output from the EXT 1 terminal 40 e The video sound signal from an EXT terminal cannot be output Teletext programmes cannot be output Connecting speakers or an amplifier See the audio equipment diagram and connect the audio equipment to the TV Before connecting anything e Read the manuals that came with the amplifier and speakers Turn the TV and amplifier off e Use impedance 8 ohm type speakers for surround speakers To prevent magnetism from the speakers affecting the TV screen use magnetic shielded speakers for the front speakers e Connecting cables are not supplied e Pay attention to the positive and negative polarities when connecting the surround speakers to your TV e For the best effect position the surround speakers at least 1 metre above the heads of seated viewers e If you want to use your external Dolby Surround decoder connect it to the AUDIO OUT terminals Then set all surround functions of the TV to OFF The output from the AUDIO OUT terminal is not cut off connecting headphones to the TV E Audio amplifier and front speakers You can use external front speakers to listen to the TV sound instead of the TV speakers For details of how to operate them see Turning the TV s speakers off on page 36 Also note that when you want to use the PRO LOGIC 3D PHONIC function you can set it to issue sound from both of the TV speakers and external front
30. annot appear unless you zoom press the Information button m DECODER EXT 2 2 Press the lt gt and V A buttons to You can only use this function if you have a choose a language decoder connected to a T V LINK Then press the OK button compatible VCR which in turn is connected to the EXT 2 terminal To use this function E AUTO PROGRAM see Using the DECODER EXT 2 To receive SKY 1 you need a satellite tuner function on page 35 You must have the satellite tuner set to SKY A 1 before starting the AUTO PROGRAM Caution function If you have not connected a decoder with You can automatically store the TV channels a T V LINK compatible VCR to the EXT 2 for which you have the best reception Store terminal setting this function to ON by them in the TV s programme numbers PR mistake causes the picture sound of a TV list by doing the following channel you are currently viewing to disappear 1 Choose AUTO PROGRAM 2 Press the OK button to start the AUTO PROGRAM function The AUTO PROGRAM menu appears and the TV channels you receive are automatically registered in the programme numbers PR list 30 Using the TV s menu e To cancel the AUTO PROGRAM function press the TV button CH 28 20 COE ow After the TV channels have been registered in the programme numbers PR the EDIT menu appears e You can now edit the programme numbers PR using the EDIT MANUAL function For det
31. ation Before using a function in the HEADPHONE SURROUND menu please be sure to connect the headphones to your TV If the headphones are not connected to the TV the DIGITAL SURROUND function becomes active instead of the HEADPHONE SURROUND function e Disconnecting the headphones from the TV automatically changes to the DIGITAL SURROUND function corresponding to the current HEADPHONE SURROUND function However the 3D HEADPHONE function is changed over to either the PRO LOGIC 3D PHONIC function or DOLBY PRO LOGIC function depending on the state at that time 3D HEADPHONE The 3D HEADPHONE function produces 3D surround effects that are heard through headphones but should be more naturally placed as if they were coming out of separate front speakers Choose 3D HEADPHONE Then press OK button To cancel the 3D HEADPHONE function Press the W A buttons to choose SURROUND OFF e You can turn the 3D HEADPHONE function on or off with a single press The 3D HEADPHONE function does not work properly for mono sound The 3D HEADPHONE function cannot play back Dolby Surround Pro Logic sound correctly E Other surround functions You can enjoy enhanced sounds while using headphones with one of the following four surround functions DANCE CLUB This function creates a dance club atmosphere It does not work properly for mono sound CONCERT HALL This function creates a concert hall atmosphere It does not work
32. bt about the installation operation or safety of this equipment consult your dealer e Handle all glass panels or covers with care e Never operate this equipment if it appears damaged or operates abnormally Turn the power off disconnect the main power plug and consult your dealer e Never remove any affixed panels or covers Doing so may result in electrical shock e Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby mode Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do so Make special arrangements for infirm or handicapped persons e Never watch TV while operating a motor vehicle It is illegal to watch TV while driving e Never listen to headphones at high volume Doing so may damage your hearing Never obstruct the ventilation of this equipment Doing so may cause overheating and result in a malfunction or damage Never use makeshift stands or attempt to affix legs with wood screws When using a manufacturer s approved stand or legs use only the fixtures provided and follow the installation instructions Never allow this equipment to be exposed to rain or moisture Never allow anyone especially children to insert anything into an opening in the case Doing so may result in a fatal electrical shock Never guess or take chances with electrical equipment of any kind It is bette
33. ch menu are related if you change one of them the others will change automatically e Setting the volume of the amplifier too high may damage the front speakers E Turning the TV s speakers off Preparation Press the 3D button to choose SURROUND OFF then turn off the surround function 1 Press the OK button to display the MENU main menu Additional Sound settings Follow Connecting speakers or an amplifier on page 40 to connect the speakers and amplifier then set the functions depending on the connection you have made When connecting an audio system front speakers and an amplifier Follow Turning the TV s speakers off and Using the TV speakers as the centre speakers for the PRO LOGIC 3D PHONIC function When connecting surround speakers Follow Setting the DOLBY PRO LOGIC function When connecting both an audio system front speakers and an amplifier and surround speakers Follow Turning the TV s speakers off and Setting the DOLBY PRO LOGIC function The lt P gt buttons of the TV remote control and the lt 1 volume buttons at 2 Press the W A buttons to choose SOUND SETTING Then press the OK button to display the SOUND SETTING menu The SOUND SETTING menu appears SOUND SETTING OfSTEREO I en BASS TREBLE BALANCE SPEAKER amp 3 Press the W A buttons to choose SPEAKER Then press the lt gt buttons to cho
34. ction given below Important Do not make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured green or green and yellow The wires in the mains lead on this product are coloured in accordance with the following code Blue Neutral Brown Live As these colours may not correspond with the coloured marking identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red When replacing the fuse only a correctly rated approved type should be used and be sure to re fit the fuse cover If in doubt consult a competent electrician How to replace the fuse Open the fuse compartment with a blade screwdriver and replace the fuse Guidelines for safe operation This equipment has been designed and manufactured to comply with international safety standards However as with any electrical appliance care must be taken to ensure optimal results and operational safety e Before attempting to use this equipment read the operating instructions thoroughly Ensure that all electrical connections including the mains plug extension leads etc have been made in accordance with the manufacturer s instructions e If ever in dou
35. e the time choose a TV channel that has teletext programmes The time will still be displayed as long as you do not turn off the TV even if you choose other TV channels e When watching videos an incorrect time is sometimes displayed Return to TV channel instantly You can return to a TV channel instantly VCR or DVD position VCR When you are using a VCR set the switch to the VCR position DVD When you are using a DVD player set the switch to the DVD position Text When you are viewing Teletext programmes set the switch to the Text position Press the TV button The TV returns to the TV mode and a TV channel appears Press the VCR DVD control button to control your VCR or DVD player e If your device is not made by JVC these buttons will not work e Even if your device is made by JVC some of these buttons may not work depending on the device you are using e You can use the V A buttons to choose a TV channel the VCR will receive or choose the chapter the DVD player plays back Some models of DVD player use the V A buttons for both operating the fast forward backward functions and for choosing the chapter In this case the lt lt gt gt buttons do not work 15 16 Teletext function MODE BS all REVEAL How wane RENE SE HOLD MODE REVE oss SIZE S C3 ll SUBPAGE 5 a work ell SUBPAGE We Cw LEi INDEX STORE CANCEL Tl a p DVD Basic operation
36. egistration mode programme number PR for a new TV channel When the registration is completed the picture of the TV channel appears on the screen The CH number is a number given to each broadcast frequency that carries a TV channel If the TV cannot detect the TV channel corresponding to the broadcast frequency indicated by the CH number a no signal picture 2 Press the blue button to activate the MANUAL function A 1 2 3 4 5 7 8 9 iar x E SEARCH we Je BEE Ep DELETE To cancel the MANUAL function 1 Press the V A buttons to choose a Press the Information button TV channel Every time you press the W A buttons the 3 Press the green or red button to programme number PR changes and the search for a TV channel picture of the TV channel stored in the Scanning stops when the TV finds a TV programme number PR appears on the channel Then the TV channel is screen displayed 4 Press the green or red button repeatedly until the TV channel you want appears If the TV channel reception is poor ow 1D 7 Press the blue or yellow button to fine MOVE EH MANUAL is tune the TV channel 2P th llow button to delet mea cpr mai Wee rg et 5 Press the OK button and register The TV channel is deleted from the the TV channel to a programme programme numbers PR list number PR The normal EDIT menu is resumed 34 Using the TV s menu E CH NUMBER When you
37. gic sound For details see PRO LOGIC 3D PHONIC Dolby Pro Logic 3D PHONIC on page 22 You can control the effect level of the PRO LOGIC 3D PHONIC function as you like TV SPEAKER For details see Additional Sound settings on page 36 LEFT CENTRE RIGHT You can adjust the sound level of each speaker separately LEFT RIGHT means left and right of the front speakers and CENTRE means the centre speaker Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories 23 Using the TV s menu E Other surround functions You can enjoy enhanced sound with one of Headphone surround 24 the following four surround functions DANCE CLUB This function creates a dance club atmosphere It does not work properly for mono sound CONCERT HALL This function creates a concert hall atmosphere It does not work properly for mono sound STADIUM This function creates a stadium atmosphere It does not work properly for mono sound HYPER SOUND This function enhances mono sound to create a stereo sound feel It does not work properly for stereo sound To cancel the function Press the W A buttons to choose SURROUND OFF The above function does not work properly for Dolby Surround encoded programmes HEADPHONE SURROUND O 3D_HEADPHONE DANCE CLUB CONCERT HALL STADIUM HYPER SOUND SURROUND OFF od Prepar
38. ing the TV s menu FEATURES O SLEEP TIMER BLUE BACK ON CHILD LOCK DECODER EXT 2 OFF ow m SLEEP TIMER You can set the TV to automatically turn off after a specified period of time 1 Choose SLEEP TIMER then press the OK button A Sub menu of the SLEEP TIMER function appears SLEEP TIMER 0 120 UE mo gt Press the lt gt buttons to set the period of time Then press the OK button You can set the period of time a maximum of 120 minutes 2 hours in 10 minute steps e One minute before the SLEEP TIMER function turns off the TV GOOD NIGHT appears The SLEEP TIMER function cannot be used to turn off the TV s main power e When the SLEEP TIMER function is on you can display the sub menu of the SLEEP TIMER function again to confirm or change the remaining period of time of the SLEEP TIMER function Press the OK button to leave the menu after confirming or changing the remaining time To cancel the SLEEP TIMER function Press the lt button to set a period of time to OFF 27 28 Using the TV s menu E BLUE BACK You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent or when there is no input from an external device ON This function is turned on OFF This function is turned off CHILD LOCK When there is a TV channel you do not want your children to watch you can use the CHI
39. mages from external equipment E Muting the sound Press the 1 muting button to turn off the sound Pressing the 1 muting button again restores the previous volume level m Use the 0 CAV button Press the 0 CAV button to choose an EXT terminal y TV mode EXT modes omma Pogam J a a 4 current time ie E1 E2 or 52 EXT 4 EXT 3 i No display awe E Use the V A buttons Press the V A buttons to choose an EXT terminal E Use the PR LIST 2 Press the lt gt and V A buttons to choose a programme number PR Then press the OK button For programme numbers PR with the CHILD LOCK function set the CHILD LOCK mark appears next to the Programme number PR in the PR LIST 1 Press the Information button to display the PR LIST e You cannot use the V A buttons to choose a programme number PR with the CHILD LOCK set e Even if you try to choose a programme 2 Press the lt gt and V A buttons to choose an EXT terminal Then press the OK button For programme numbers PR where 12 number PR with the CHILD LOCK set the CHILD LOCK mark will appear and you cannot watch the TV channel To watch the TV channel see you have the CHILD LOCK function set the CHILD LOCK mark appears next to the programme number CHILD LOCK on page 28
40. mpatible VCR set the DECODER EXT 2 function to ON For details see Using the DECODER EXT 2 function on page 35 Otherwise you will not be able to watch scrambled channels E Rear Panel Mains outlet 7 AC 220 240 Aerial V 50 Hz Back of the TV DOO 2 OLA power Cord aerial oom lu oaxia oe Cable To Aerial Input aerial plug AV IN OUT Terminal WOOFER terminal page 39 2 AUDIO OUT terminal page 40 SURROUND REAR terminal page 39 EXT 1 terminal pages 5 25 39 EXT 2 terminal pages 5 8 25 39 EXT 3 terminal pages 25 39 Aerial socket page 5 Setting up your TV Putting the batteries into the Remote control Use two AAA RO3 dry cell batteries Insert the batteries from the end making sure the and polarities are correct JIC e Follow the warnings printed on the batteries e Battery life is about six months to one year depending on how much you use the remote control e The batteries we supply are only for setting up and testing your TV please replace them as soon as you need to e Ifthe remote control does not work properly replace the batteries Initial settings When the TV is first turned on it goes into the initial setting mode and you will see the JVC logo F
41. n adds a new TV channel in the current programme numbers PR list by using the CH number e You cannot use the INSERT function if you do not know a channel number of a TV channel Use the MANUAL function to register a TV channel in the programme number PR DELETE This function deletes a TV channel you do not want to list MANUAL This function manually stores a new TV channel in a programme number PR If you do not have a T V LINK compatible VCR connected Press the TV button to exit the T V LINK menu The T V LINK menu disappears and all the settings are completed If you have a T V LINK compatible VCR connected Follow the operating procedure Downloading data to a VCR on page 35 to transmit the programme number PR data to the VCR MOVE 1 Press the W A buttons to choose a TV channel Every time you press the V A buttons the programme number PR changes and the picture of the TV channel stored in the programme number PR appears on the screen Press the gt button to start the MOVE function CH28 Press the W A buttons to choose a new programme number PR To cancel the MOVE function Press the Information button 32 Using the TV s menu 4 Press the lt button to change the programme number PR of a TV channel to a new programme number PR 1 Press the W A buttons to choose a TV channel Every time you press the V A buttons the programme number
42. nction which corresponds to the current DIGITAL SURROUND function However the PRO LOGIC 3D PHONIC function and DOLBY PRO LOGIC function are changed over to the 3D HEADPHONE function as headphones cannot play back the Dolby Surround Pro Logic sound properly m PRO LOGIC 3D PHONIC Dolby Pro Logic 3D PHONIC The PRO LOGIC 3D PHONIC function lets you enjoy the atmosphere of Dolby Surround Pro Logic sound without needing extra surround speakers With the PRO LOGIC 3D PHONIC function you can use the rear surround channel signal of the Dolby Surround encoded programme to create the surround sound image as if surround speakers were located at your right and left Use the PRO LOGIC 3D PHONIC function Choose PRO LOGIC 3D PHONIC Then press the OK button To cancel the PRO LOGIC 3D PHONIC function Press the W A buttons to choose SURROUND OFF The PRO LOGIC 3D PHONIC function does not work properly except for Dolby Surround encoded programmes e You can turn the PRO LOGIC 3D PHONIC function on or off by pressing the 3D button Using the TV s menu 3 Press the OK button to complete the setting e To change the TV speaker setting you should connect an audio system to the TV For details see Connecting speakers or an amplifier on page 40 Change the setting of the PRO LOGIC 3D PHONIC function 1 Choose PRO LOGIC 3D PHONIC e When an audio system is not connected to your TV please be sure to
43. o noise reduction AUTO This mode reduces any noise interference or snowing in the current picture The function also adjusts the optimum sharpness of the picture SHARP MIN The AUTO VNR function is cancelled If you set the mode to AUTO but feel that the sharpness of the original picture has not been reproduced fully change the mode to MIN However any noise remaining in the original picture may be emphasized MAX This mode always reduces any noise as much as possible irrespective of state of the picture When you set the mode to AUTO but still notice some noise change the mode to MAX However this may reduce the sharpness of the picture m COLOUR SYSTEM The colour system is chosen automatically However if the picture is not clear or no colour appears choose the colour system manually COLOUR SYSTEM PAL mw Ww L 1 Choose COLOUR SYSTEM then press the OK button 2 Press the lt gt buttons to chose the appropriate colour system Then press the OK button PAL PAL system NTSC 3 58 NTSC 3 58 MHz system NTSC 4 43 NTSC 4 43 MHz system AUTO This function detects a colour system from the input signal You can only use this when you are viewing a picture from programme number PR 0 AV or EXT terminal The AUTO function may not work properly if you have poor signal quality If the picture is abnormal in the AUTO function choose another colour system manually
44. o the full screen f Q Q Q Q SUBTITLE SUBTITLE SUBTITLE SUBTITLE 13 Remote control buttons and functions FULL This uniformly stretches the left and right sides of a normal picture 4 3 aspect ratio to picture pllithe Wwide TV sereen e You cannot adjust the visible area in ei Co REGULAR or FULL mode ie o e 0 e For 16 9 aspect ratio pictures that have PRO LOGIC 3D PHONIC been squeezed into a normal picture 4 3 function aspect ratio use the FULL mode to 3 While it is displayed press the V A buttons to change the height of the restore the picture to its original shape You can turn the PRO LOGIC 3D PHONIC function on or off or you can switch to the m Choose the ZOOM mode 3D HEADPHONE function by one touch 1 Press the ZOOM button to display operation the ZOOM menu Press 3D button Pressing 3D button changes the function as follows O AUTO WSS REGULAR PANORAMIC PRO LOGIC 3D PHONIC or 3D HEADPHONE 0 M ZOOM SUBTITLE 2 Press the V A buttons to choose a ZOOM mode Then press the OK z bution The picture expands and the chosen t ZOOM mode is displayed in about 5 If some other surround function is i f i i f i i i SURROUND OFF i i i i i i i i i seconds activated before you press the 3D button You can pre set a ZOOM mode for the you can return to that surround function normal picture See 4 3 AUTO The PRO LOGIC 3D PH
45. ollow the instructions on the screen display to make the initial settings Bw IL Blue button ct agod TV ce ees Q Via SSP lt i gt 1 Press the Main power button on the TV The Power lamp lights red for power on then green for TV on and the JVC logo appears Power lamp Main power button If the power lamp stays red and does not change to green your TV is in the standby mode Press the O I standby button on the remote control to turn your TV on Ifthe JVC logo does not appear this is because your TV has already been turned on for the first time use the LANGUAGE and AUTO PROGRAM functions to make the initial settings For details see INSTALL on page 29 Setting up your TV 2 Press the OK button The LANGUAGE menu appears LANGUAGE OUNGLISH FRAN AIS DEUTSCH ITALIANO CASTELLANO NEDERLANDS DANSK NORSK SVENSKA SUOMI 5 Press the OK button to display the T V LINK menu T V LINK DOWNLOAD TV VCR EA Press the V A buttons to choose ENGLISH The on screen display will then be in English To receive SKY 1 you need a satellite tuner You must have the satellite tuner set to SKY 1 before starting the AUTO PROGRAM function which follows Press the OK button to start the AUTO PROGRAM function The AUTO PROGRAM menu appears and received TV channels are automatically stored in the programme numbers PR To cancel the
46. olume to control and set the volume of the front speakers to fit in with the TV speakers E Setting the DOLBY PRO LOGIC function Set the items in the sub menu of the DOLBY PRO LOGIC function properly and use the test signal to control the volume of the speakers so that you can listen to the sounds from them evenly Be sure to do this operation before using the DOLBY PRO LOGIC function Preparation e Ifyou have had the headphones connected to your TV set disconnect them Increase the volume of the TV speakers to a level at which you ordinarily listen If you do not do this before starting the operation it is impossible to control the volume from within the function When you are using an audio system however set the amplifier volume to zero to cut the front speakers Then pre set the TV sound volume level to about 10 1 Press the OK button to display the MENU main menu 2 Press the W A buttons to choose DIGITAL SURROUND Then press the OK button to display the DIGITAL SURROUND menu 3 Press the W A buttons to choose DOLBY PRO LOGIC Then press the gt button to display the sub menu of the DOLBY PRO LOGIC function DOLBY PRO LOGIC OMV SPEAKER TEST MODE OFF LEFT CENTRE Cc RIGHT C0 CT SURROUND 5 O 38 Additional menu operations 4 Press the W A buttons to choose TV SPEAKER Then press the lt gt buttons to choose the TV speaker setting When you are connecting only
47. on having a stored page op To leave the List mode Press the MODE button again Hold You can hold a teletext page on the screen for as long as you want even while several other teletext pages are being received Press the HOLD button Hold indication 102 103 To cancel the Hold function Press the HOLD button again Sub page Some teletext pages include sub pages that are automatically displayed You can hold any sub page or view it at any time 1 Press the SUBPAGE button to operate the sub page function 2 Press the Number buttons to enter a sub page number Example 3rd sub page press 0 CAV 0 CAV O CAV and 3 To cancel the sub page function Press the SUBPAGE button again e You can also choose a sub page by pressing the red or green button Reveal Some teletext pages include hidden text such as the answers to a quiz You can display the hidden text Each time you press the REVEAL button text is hidden or revealed No x WN ou 100 101 102 103 Teletext function Size You can double the height of the teletext display Press the SIZE button TEXT ATF SIZE Index You can return to the index page instantly Press the INDEX button FLOF Fastext TOP WST World Standard Text Returns to page 100 or a previously specified page List mode Returns to the page number displayed in the lower left
48. on to display the MENU The MENU main menu appears 4 Press the W A buttons to choose FEATURES Then press the OK button The FEATURES menu appears FEATURES OfSLEEP TIMER BLUE BACK ON CHILD LOCK DECODER CEXT 2 OFF O W 5 Press the W A buttons to choose DECODER EXT 2 Then press the lt gt buttons to choose ON An unscrambled picture appears To cancel the DECODER EXT 2 function Press the lt gt buttons to choose OFF 6 Press the OK button to complete the setting The T V LINK menu appears T V LINK DOWNLOAD TV VCR E 35 36 Additional menu operations 7 Follow Downloading data to a VCR on page 35 to transmit the programme number PR data to the VCR 8 If you have another TV channel you want to unscramble using a decoder repeat steps 2 to 7 If the DECODER EXT 2 function has been set to ON but the TV channel cannot be unscrambled check the following e Has the decoder been connected to the VCR properly according to the VCR and decoder instruction manuals e Has the decoder power been turned on e Can the TV channel be unscrambled with a decoder e Do you need to change the VCR settings in order to connect the decoder Confirm that the VCR is set properly by rechecking the VCR Instruction manual the front panel of your TV set can be used to control the volume of all the speakers at once e The settings of the TV speakers on ea
49. orce when inserting the connector into the WOOFER terminal Use of excessive force may damage the connector 41 42 Troubleshooting If a problem arises while you are using the TV please read this troubleshooting guide carefully before you ask to have the TV repaired You may be able to fix it easily by yourself For example if the mains plug is disconnected from the mains outlet or the TV aerial has problems you may think there is a problem with the TV itself Important This troubleshooting guide only covers problems whose causes are not easy to decide If you have a question when you are operating a function read the page s for that function carefully not this troubleshooting guide e If you follow the advice in this troubleshooting guide without any success unplug the mains plug and ask for your TV to be repaired Do not attempt to repair the TV by yourself or to remove the rear cover of the TV E If you cannot turn on the TV e Ifthe TV or aerial suffers interference e Is the mains plug connected to the mains from other equipment stripes or noise outlet may appear in the picture Move any e Is the power lamp lit If not press the equipment such as an amplifier personal main power button computer or a hair drier that can cause interference away from your TV Or try E No picture or no sound moving the TV If the aerial suffers e Have you chosen a TV channel with very interference from a radio tower or high poor
50. ose OFF The sound from the TV speakers is cut 4 Press the OK button to complete the settings The menu disappears E Using the TV speakers as the centre speakers for the PRO LOGIC 3D PHONIC function When the PRO LOGIC 3D PHONIC function is operating the front speakers and TV speakers are all used The TV speakers take the role of a centre speaker It makes spoken dialogues more vivid and easier to listen to Preparation e If you have had headphones connected to your TV set disconnect them 1 Press the OK button to display the MENU main menu 2 Press the W A buttons to choose DIGITAL SURROUND Then press the OK button to display the DIGITAL SURROUND menu 3 Press the V A buttons to choose PRO LOGIC 3D PHONIC Then press the gt button to display the sub menu of PRO LOGIC 3D PHONIC function PRO LOGIC 3D PHONIC MODE NORMAL OLEVEL TV SPEAKER L C R SSS LEFT CENTRE T1 RIGHT Cd WW K 4 Press the V A buttons to choose TV SPEAKER Then press the lt gt buttons to choose CENTRE L C R L C R is used to make all the sound come from the TV speakers OFF OFF is used to cut sound from the TV speakers When the sound quality of the audio system is better than the TV s speakers you can set the TV SPEAKER to OFF to cut the sound of the TV speakers Additional menu operations 5 Press the OK button to complete the settings The menu disappears e Use the amplifier v
51. properly for mono sound STADIUM This function creates a stadium atmosphere It does not work properly for mono sound HYPER SOUND This function enhances mono sounds to create a stereo sound feel It does not work properly for stereo sound To cancel the function Press the W A buttons to choose SURROUND OFF The above function does not work properly for Dolby Surround encoded programmes Using the TV s menu EXT SETTING EXT SETTING EXT 1 DUBBING EXT 2 EXT 3 DUOS TV Ox lt S S VIDEO input You can connect a device such as an S VHS VCR to enjoy the high quality picture of the S VIDEO signal Y C signal Preparation e First read the device s instruction manual and Additional preparation on page 39 to connect the device to the TV properly Second follow the device s instruction manual to set the device so that it sends an S VIDEO signal Y C signal to the TV Do not set S amp S VIDEO input to an EXT terminal connected to a device which cannot output an S VIDEO Y C signal If it is set wrongly a picture cannot appear 1 Choose an EXT terminal 2 Press the yellow button and set the S S VIDEO input Then press the OK button An S S VIDEO input mark is displayed You can view an S VIDEO signal Y C signal instead of the regular video signal composite signal 25 26 Using the TV s menu To cancel the S amp S VIDEO
52. r to be safe than sorry Caution The woofer unit is mounted on the TV Always move the TV and woofer unit together when removing the TV from the box or when moving the woofer unit If the TV is tilted during movement the woofer unit may fall Be careful to keep the TV level when moving it Do not grip the woofer unit when moving the TV Do not place objects on the woofer unit duct LIFTING CAUTION FREE WOOFER UNIT KEEP WITH UNIT Setting up your TV Caution Turn off all the equipment including the TV before connecting anything Connecting the aerial and video cassette recorder VCR The connecting cables are not provided e For further details refer to the manuals provided with the devices to be connected E If you are connecting a VCR follow gt gt gt OM in the diagram opposite E If you are not connecting a VCR follow gt To use the T V LINK functions you must have a T V LINK compatible VCR connected by a SCART cable to the EXT 2 terminal on the TV For details about T V LINK functions see T V LINK functions on page 8 You can watch a video using the VCR without doing For details see your VCR instruction manual To connect more equipment please see Additional preparation on page 39 To connect external speakers and an audio system please see Connecting speakers or an amplifier on page 40 If you connect a decoder to a T V LINK co
53. reen size according to the picture aspect ratio Choose the optimum one from the following ZOOM modes AUTO WSS For any picture format except normal picture 4 3 aspect ratio the picture will be automatically displayed in the ideal screen size For normal picture 4 3 Aspect Ratio you can choose a ZOOM mode from the 4 3 AUTO ASPECT menu For details see 4 3 AUTO ASPECT on page 21 e AUTO may not work properly with poor signal quality In this case choose the best ZOOM mode manually Remote control buttons and functions This TV supports WSS wide screen signals When broadcasts with WSS are received with the ZOOM mode set at AUTO WSS the most suitable ZOOM mode is automatically chosen according to the WSS received REGULAR Use to view a normal picture 4 3 aspect ratio as this is its original shape O o O o OP LO eee oo PANORAMIC This stretches the left and right sides of a normal picture 4 3 aspect ratio to fill the screen without making the picture appear unnatural fo oO e oO ORFO fe o e The top and bottom of the picture are slightly cut off 14 9 ZOOM This zooms up the wide picture 14 9 aspect ratio to the upper and lower limits of the screen o O e O fo Oo e 16 9 ZOOM This zooms up the wide picture 16 9 aspect ratio to the full screen LO HO 16 9 ZOOM SUBTITLE This zooms up the wide picture 16 9 aspect ratio with subtitles t
54. signal the correct rear panel and front panel 2 VCR composite signal S VIDEO signal connections T V LINK compatible VCR composite Before connecting anything signal S VIDEO signal e Read the manuals that came with the Decoder equipment DVD player composite signal S VIDEO Depending on the equipment the signal connection method may be different from DVD player composite signal RGB the diagram Also the equipment settings signal may need to change depending on the TV game composite signal RGB signal connection method TV game composite signal S VIDEO Turn off all the equipment including the signal TV Headphones The Specifications on the back cover Camcorder composite signal S VIDEO give the details of the EXT terminals If signal you are connecting equipment not listed SCART cable in the following connection diagram see Audio cable the table to choose the best EXT terminal Video cable e Connecting cables are not supplied ae S VIDEO cable Back of the TV Additional preparation E Equipment which can output the S VIDEO signal Y C signal such as an S VHS VCR Connect the equipment to an EXT terminal but not the EXT 1
55. ss the P V A buttons to turn the TV on from standby mode Choose a TV channel Press the P V A buttons to choose a programme number PR or an EXT terminal Adjust the volume 1 Press the 1 Volume button The volume level indicator appears 2 Press the buttons while the volume level indicator is on screen Remote control buttons and functions Muting button Number buttons ZOOM button 3D button Information button TV button lt gt buttons Standby button Colour buttons OK button O V A buttons 4 VCR DVD Teletext control button 3 VCR E DVD switch Text button Turn the TV on or off from HOLD MODE REVEAL SWE standb mode IS 20 ll eo y YO O amp Press the I standby button to turn the TV on or off When the TV is turned on the power lamp changes from red to green The power can be turned on by pressing the TV button V A buttons or Number buttons Choose a TV channel E Use the number buttons Enter the programme number PR of the channel using the number buttons Example e PR6 gt press 6 e PR12 press 1 and 2 E Use the V A buttons Press the V A buttons to choose the programme number PR you want 11 Remote control buttons and functions E Use the PR LIST 1 Press the Information button to display the PR LIST Pressing the information button changes the display as follows on Watch i
56. to a normal state it is not a failure E Other issues e When the SLEEP TIMER function operates the TV is automatically turned off Ifthe TV is turned off suddenly try to press the I standby button to turn on the TV once again If the TV goes back to normal there is no problem e When the TV is receiving a wide screen signal WSS or a signal from an external device affecting the screen size the ZOOM mode automatically changes When you want to resume the previous ZOOM mode press the ZOOM button again Troubleshooting If you bring a magnetised equipment such as a speaker near to your TV the picture may be warped or unnatural colours now appear at the corners of the screen In this case keep the equipment away from your TV If speakers cause this to happen use magnetic shielded speakers instead A picture may be tilted due to the earth s own magnetic field If so use the PICTURE TILT not AV28R25EK AV28R250EK on page 21 to correct the tilt The TV may make a crackling sound due to a sudden change in temperature The picture or sound may be normal If you hear crackling sounds frequently while you are viewing the TV there may be other causes As a precaution ask your service technician to inspect it Touching the screen may cause you to feel a slight electric shock due to its static electricity This is unavoidable due to the construction of the picture tube It is not a problem with the TV You can
57. ttons and functions 11 Teletext function 16 Using the TV s menu 18 Additional menu operations 35 Additional preparation 39 Troubleshooting 42 Specifications Back cover plain English approved by the word centre Thank you for buying this JVC colour television To make sure you understand how to use your new TV please read this manual thoroughly before you begin WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION Operate only from the power source specified The main power button on the TV does not AC 220 240 V 50 Hz on the unit fully isolate the TV from the mains supply If e Avoid damaging the AC plug and power cord you are not going to use this TV for a long When you are not using this unit for a long period of time be sure to disconnect the mains period of time it is recommended that you plug from the mains outlet disconnect the power cord from the main outlet Avoid improper installation and never position the unit where good ventilation is unattainable When installing this TV distance recommendations must be maintained between the floor and wall as well as installation in a tightly enclosed area or piece of furniture Adhere to the minimum distance guidelines shown for safe operation Failure to heed the following precautions may res
58. ult in damage to the TV or remote control DO NOT block the TV s ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be able to get out DO NOT place anything on top of the TV such as cosmetics or medicines flower vases potted plants cups etc DO NOT allow objects or liquid into the cabinet openings If water or liquid is allowed to enter this equipment fire or electric shock may be caused DO NOT place any naked flame sources such as lighted candles on the TV The surface of the TV screen is easily damaged Be very careful with it when handling the TV Should the TV screen become soiled wipe it with a soft dry cloth Never rub it forcefully Never use any cleaner or detergent on it In the event of a fault unplug the unit and call a service technician Do not attempt to repair it yourself or remove the rear cover E Warning DO NOT cut off the mains plug from this equipment If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or adaptor or consult your dealer If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately to avoid a possible shock hazard by inadvertent connection to the mains supply If a new mains plug has to be fitted then follow the instru
59. unction Here are the details about these functions Caution e Using the MOVE DELETE or INSERT functions rewrites the current programme numbers PR list Therefore the programme numbers PR of some of the TV channels will change e Using the MANUAL function for a TV channel for which the CHILD LOCK function has been set cancels the CHILD LOCK function for that channel e Using the MANUAL function for a TV channel for which the DECODER EXT 2 function has been set to ON returns the setting of the DECODER EXT 2 function for that channel to OFF e When a TV channel has already been registered in PR 99 using the INSERT function deletes that TV channel Using the TV s menu 1 Choose EDIT MANUAL then press the OK button For programme number PR 0 AV appears in the programme numbers PR list e An EXT terminal number does not appear in the programme numbers PR list The CH number is a number unique to the TV and corresponding to the channel number of a TV channel For the relationship of a channel number and a CH number see CH NUMBER on page 34 3 Press the OK button to complete the settings The T V LINK menu appears T V LINK DOWNLOAD TV VCR Follow the description for a function you want to use MOVE This function changes a programme number PR of a TV channel ID This function registers a channel name ID to a TV channel INSERT This functio
60. vel Then press lt weaker the OK button gt strong TREBLE You can adjust the high tone of the sound lt 4 weaker gt strong Using the TV s menu BALANCE You can adjust the volume balance between the left and right speaker lt turn the left speaker s volume level up gt turn the right speaker s volume level up e When the DOLBY PRO LOGIC function or PRO LOGIC 3D PHONIC function is operating the BALANCE item does not appears SPEAKER You can turn off the sound from the TV speakers but you should only do this if you have connected an audio system to the TV instead of the TV speakers When you are using this function see Turning the TV s speakers off on page 36 ON The TV speakers issue sound OFF The TV speakers do not issue sound The lt gt buttons of the TV remote control and the 1 volume buttons at the front panel of your TV set can be used to control the volume of each speaker simultaneously e Setting the volume of the amplifier too high may damage the front speakers e When the DOLBY PRO LOGIC function or PRO LOGIC 3D PHONIC function is operating the SPEAKER item does not appears Digital surround DIGITAL SURROUND O PRO_ LOGIC 3D PHONIC P DOLBY PRO LOGIC gt DANCE CLUB CONCERT HALL STADIUM HYPER SOUND SURROUND OFF mw amp e Connecting the headphones to the TV automatically changes to the HEADPHONE SURROUND fu

JVC AV32R25EK CRT Television User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents