Jensen BT1613 Car Stereo System User Manual
Contents
1. Dark Blue to the power antenna or an amplifier If not amp fast blow ATO used tape the bare end of wire Ground black wire T blac D Connect to the ground terminal or a a D clean unpainted part of the chassis JN pate JENSEN PHASE Yellow 7 Memory Battery yellow wire SERIES 7 a Connect to the battery or to a 12 volt RCA Outputs to Amplifier power source that is always live The radio will not work if this wire is not connected Accessory Ignition red wire Red S i Connect to the existing radio wire or radio Left Front Speaker ARAR N fuse Installation Guide White Black Grey Black Pod White Right Front Speaker aie jinik iPod Cable Left Rear Speaker Green Black Violet Black Right Rear Speaker Green Violet MENU N Bluetooth DISP iPod B SRC OPY TEEF TEEF TRANSFER ZY r l c f i it H fi iid 7 i EE BEEE F 4 T i a l I I e Ir F I ee oe oe 1D3 Fea anual d PS AS 4x 40W Speaker Requirements Mounting Sleeve Installation Only connect speakers rated with a load impedance of 4 ohms Speakers with a load impedance of less than 4 1 Push the REL button and remove the detachable front panel ohms could damage the unit from the chassis Remove the trim ring by lifting in the center and pulling it off Preparation from either side N o o E3 Remove the mounting sleeve This unit i2. Wiring Diagram IMPORTANT Incorrect wiring connections can damage the unit Follow the wiring instructions carefully or have the installation handled by an experienced technician What s tn the Box Tools and Supplies BT1613 Head Unit You will need these tools and supplies to install your Cosmetic Trim Ring BT1613 Need Help For technical assistance call the Jensen customer support line at 1 800 323 4815 Antenna 0 _ _ 15 Amp Fuse NOTE When replacing a t fuse make sure the new TE fuse is the correct type and amperage Using an incorrect fuse could damage the radio This head unit uses one 15 amp fuse located below Subwoofer Output iPod jLink connector Use this 8 pin DIN socket to connect your jLink iPod cable gt Power Antenna dark blue wire Connect e Wiring Harness Power Speaker e Mounting Hardware e Remote Control e jLink iPod Cable e 3 5mm Media Cable e Owners Manual e Installation Guide Torx type flat head and Philips screwdrivers Wire cutters and strippers Tools to remove existing radio screwdriver socket wrench set or other tools Electrical tape Crimping tool Volt meter test light Crimp connections 18 gauge wire for power connections 16 18 gauge speaker wire WARNING Never install this unit where operation and viewing could interfere with safe driving conditions the wiring connector 15
3. l tape to ensure proper operation WARNING Only connect the unit to a 12 volt power supply with proper grounding After completing the wiring connections attach the front panel and turn the unit on to confirm operation vehicle ignition switch must be on If the unit does not operate recheck all wiring until the problem is corrected Once proper operation is achieved turn the ignition switch off and proceed with final mounting of the chassis Carefully slide the radio into the half sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place 9 Attach one end of the perforated support strap supplied to the screw stud on the rear of the chassis using the hex nut provided Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided Bend the strap as necessary to position it CAUTION The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration 10 Re attach the decorative trim ring To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to installation NOTE If this unit is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be los
4. s designed for installation in cars trucks and vans with an existing radio opening In many Cases a a Insert the removal keys straight back until they lock If special installation kit will be required to mount the radio to the dashboard These kits are available at electronics removal keys are inserted at an angle they will not lock supply stores and car stereo specialty shops Always check the kit application before purchasing to make sure the kit works with your vehicle If you need a kit but cannot locate one call our customer support line at 1 800 323 b 4815 U S A and Canada only properly to release the unit Slide the mounting sleeve off the chassis 4 Install the mounting sleeve in the dashboard a Check the dashboard opening size by sliding the mounting sleeve into it If the opening is not large enough carefully cut or file as necessary until the sleeve easily slides into the opening Do not force the sleeve into the opening or cause it to bend or bow b Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully inserted into the dashboard opening bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard 5 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrica
5. t Under these conditions use extra caution during installation to avoid causing a short circuit 2 Remove transport screws ISO DIN Installation This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard Please consult with your local car stereo shop for assistance on this type of installation Remove the existing factory radio from the dashboard or center console mounting Save all hardware and brackets as they will be used to mount the new radio Carefully unsnap the plastic frame from the front of the new radio chassis Remove and discard the frame Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio CAUTION Do not exceed M5 X 9MM screw size Longer screws may damage components inside the chassis Wire the new radio to the vehicle as outlined in the Mounting Sleeve Installation instructions Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1 Steps 8 9 CAUTION Be careful not to damage the car wiring 11 Re attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit NOTE For proper operation of the CD MP3 player the chassis must be mounted within 20 of horizontal Make sure the unit is mo
6. unted within this limitation
Download Pdf Manuals
Related Search