Husqvarna 326RJx Trimmer User Manual
Contents
1. Only intended for trimmer heads Other symbols decals on the machine refer to special certification requirements for certain markets The engine is switched off by moving the stop switch to the stop position CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance Always wear approved protective gloves Regular cleaning is required Visual check Approved eye protection must always be used 1151472 95 Rev 1 2009 01 16 CONTENTS Contents KEY TO SYMBOLS Sn I ET 2 CONTENTS Contents saro 3 Note the following before starting m 3 INTRODUCTION Dear customer 4 4 WHAT IS WHAT What is what on the trimmer nn 5 GENERAL SAFETY PRECAUTIONS TIO CLI stricnina 6 Personal protective equipment pp 6 Machine s safety equipment pp 7 Cutting equipment nu ee 9 ASSEMBLY Fitting the J handle 11 Assembling the cutting equipment 11 Fitting a trimmer guard and Superauto Il 1 trimmer A ee ee ee 11 Fitting the blade guard combination guard grass blade and grass cutter nennen nnnennenenn 12 Fitting other guards and cutting attachments 12 FUEL HANDLING S E siii ionici 13 P O cinto tiro porto 13 FUCINO sea 14 START2. Fine adjustment e When the machine has been run in the carburetor should be finely adjusted The fine adjustment should be carried out by a qualified person First adjust the L jet then the idling screw T and then the H jet Conditions Before any adjustments are made make sure that the air filter is clean and the air filter cover is fitted If you adjust the carburettor when the air filter is dirty it will result in a leaner mixture when the filter is finally cleaned This can lead to serious engine damage e Carefully turn both jets L and H so that they are midway between fully screwed in and fully screwed out e Do not attempt to adjust the L and H jets beyond either stop as this could cause damage e Now start the machine according to the starting instructions and let it warm up for 10 minutes CAUTION If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti clockwise until the cutting attachment stops Low speed jet L Try to find the highest idling speed turning the low speed needle L clockwise respectively counter clockwise When the highest speed has been found turn the low speed needle L 1 4 turn counter clockwise D 1 4 9 CAUTION If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti clockwise until the cutting attachment stops Fine adjustment of the idle speed T
3. Use soap and water 3 If the machine is leaking fuel Check regularly for leaks from the fuel cap and fuel lines Transport and storage Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames for example from electrical machinery electric motors electrical relays switches or boilers e When storing and transporting fuel always use approved containers intended for this purpose e When storing the machine for long periods the fuel tank must be emptied Contact your local gas station to find out where to dispose of excess fuel e Ensure the machine is cleaned and that a complete service is carried out before long term storage e The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage e In order to prevent unintentional starting of the engine the spark plug cap must always be removed during long term storage if the machine is not under close supervision and when performing all service measures WARNING Take care when handling fuel Bear in mind the risk of fire explosion and inhaling fumes Fuel CAUTION The machine is equipped with a two stroke engine and must always been run using a mixture of gasoline and two stroke engine oil It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained When mixing small amou
4. It is extremely important that you read and understand the contents of this operator s manual EMISSION CONTROL INFORMATION A Husqvarna NA HUSQVARNA AB HUSKVARNA SWEDEN _ HON THIS ENGINE MEETS US EPA AND CALIFORNIA EXH EVP REGS FOR EE SORE REFER TO OPERATOR S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS EMISSONS COMPLIANCE PERIOD J The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal and Californian emissions requirements The engine exhaust from this product contains chemical known to the State of California to cause cancer birth defects or other reproductive harm English 3 INTRODUCTION Dear customer Congratulations on your choice to buy a Husqvarna product Husqvarna is based on a tradition that dates back to 1689 when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River for production of muskets The location was logical since water power was harnessed from the Huskvarna River to create the water powered plant During over 300 years of continuous operation the Husqvarna factory has produced a lot of different products from wood stoves to modern kitchen appliances sewing machines bicycles motorcycles etc In 1956 the first motor driven lawn mowers appeared followed by chain saws in 1959 and it is within thi
5. cutting attachment it is extremely important that the raised section on the drive disc support flange engages correctly in the centre hole of the cutting attachment If the cutting attachment is fitted incorrectly it can result in serious and or fatal personal injury Slide the spacer into the slot in the loop handle e Fit the nut knob and screw Do not overtighten Attach the J handle to the loop handle using the three WARNING Never use a cutting attachment screws as shown without an approved guard See the chapter on Technical data If an incorrect or faulty guard is fitted this can cause serious personal injury IMPORTANTI If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar blade guard and harness e Now adjust the trimmer to give a comfortable working position Tighten the bolt knob Fitting a trimmer guard and Superauto Il 1 trimmer head WARNING Only grass blades grass cutters or trimmer heads plastic blades may be used when the J handle is fitted Saw blades must never be used with the J handle e Fit the correct trimmer guard A for use with the trimmer head Hook the guard onto the fitting on the shaft and secure it with the bolt L e Fit the drive disc B on the output shaft e Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing e Insert the locking pin C in
6. drive disc before adjusting the high speed jet H The high speed jet H is adjusted correctly when the machine burbles a little If the machine races then the setting is too lean If the engine produces a lot of smoke and burbles a lot then the setting is too rich CAUTION For optimum adjustment of the carburettor contact a qualified dealer service workshop that has a revolution counter at their disposal 1151472 95 Rev 1 2009 01 16 Correctly adjusted carburetor When the carburetor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed It is also important that the cutting attachment does not rotate at idle If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration If the high speed jet H is set too lean it will result in less power less performance poor acceleration and or damage to the engine If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed Muffler fo me CAUTION Some mufflers are fitted with a catalytic converter See chapter on Technical data to see whether your machine is fitted with a catalytic converter The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator The exhaust gases are hot and can contain sparks which may cause fire if directed against dry and combustible material Some mufflers are equ
7. is extremely important that you read and understand the contents of this operators manual You must use approved personal protective equipment whenever you use the machine Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen Ask your dealer for help in choosing the right equipment WARNING Listen out for warning signals or shouts when you are wearing hearing protection Always remove your hearing protection as soon as the engine stops HELMET A protective helmet where there is a risk of falling objects HEARING PROTECTION Wear hearing protection that provides adequate noise reduction EYE PROTECTION Always wear approved eye protection lf you use a visor then you must also wear approved protective goggles Approved protective goggles must comply with standard ANSI Z87 1 in the USA or EN 166 in EU countries GLOVES Gloves should be worn when necessary e g when fitting cutting attachments 1151472 95 Rev 1 2009 01 16 GENERAL SAFETY PRECAUTIONS CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches Always wear heavy long pants Do not wear jewellery shorts sandals or go barefoot Secure hair so it is above shoulder level FIRST AID KIT Always have a first aid kit nearby It Machine s safety equipment This section describes the machine s safety
8. the spark plug is fitted with a suppressor Clean the machine s cooling system Clean or replace the spark arrestor screen on the muffler only applies to mufflers without a catalytic converter Clean the outside of the carburettor and the space around it Check that the bevel gear is filled three quarters full with lubricant Fill if necessary using special grease Check the fuel filter from contamination and the fuel hose from cracks or other defects Replace if necessary Check all cables and connections Check the clutch clutch springs and the clutch drum for wear Replace if necessary by an autorized service workshop Replace the spark plug Check that the spark plug is fitted with a suppressor Check and clean the spark arrestor screen on the muffler only applies to mufflers fitted with a catalytic converter 24 English 1151472 95 Rev 1 2009 01 16 Technical data TECHNICAL DATA 326RJX Engine Cylinder displacement cu in cm 1 50 24 5 Cylinder bore inch mm 1 34 34 0 Stroke inch mm 1 06 27 ldle speed rpm 2700 Recommended max fast idle speed rom 11000 11700 Speed of output shaft rom 8014 Max engine output acc to ISO 8893 0 9 8400 Catalytic converter muffler Yes Speed regulated ignition system Yes Ignition system Manufacturer type of ignition system Spark plug Electrode gap inch mm Fuel and lubrication system Manufacturer type of carburetor Fuel tank capacity US pint litre WalbroMB S
9. to the instructions on the blade packaging WARNING Always stop the engine before doing any work on the cutting attachment This continues to rotate even after the throttle has been released Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it WARNING Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of blade thrust Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass English 9 GENERAL SAFETY PRECAUTIONS General rules Only use cutting attachments with the guards we recommend See the chapter on Technical data N Keep the teeth of the blade correctly sharpened Follow our instructions and use the recommended file gauge An incorrectly sharpened or damaged blade increases the risk of accidents 4 y Check the cutting attachment for damage or cracks A damaged cutting attachment should always be replaced N V A E ST Sharpening grass cutters and grass blades e See the cutting attachment packaging for correct sharpening instructions Sharpen blades and cutters using a single cut flat file e Sharpen all edges equally to maintain the balance of the blade WARNING Always discard a blade that is bent twisted cracked broken or damaged in any other way Never attempt to str
10. 60 080 ww 2 0 c IR Eu 1151472 95 Rev 1 2009 01 16 hd S35 A LE 1151472 95 Rev 1 2009 01 16 DN i 1 2 4 2 7 mm 095 106 1151472 95 Rev 1 2009 01 16 T35 35x 1151472 95 Rev 1 2009 01 16 1151472 95 MAMI cono
11. Adjust the idle speed using the idle adjustment screw T if it is necessary to readjust First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate Then turn the screw anticlockwise until the cutting attachment stops The idle speed is correctly adjusted when the engine 1151472 95 Rev 1 2009 01 16 MAINTENANCE will run smoothly in every position The idle speed should also be well below the speed at which the cutting attachment starts to rotate WARNING If the idle speed cannot be adjusted so that the cutting attachment stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired High speed jet H The high speed jet H affects the engine power speed temperature and fuel consumption If the high speed jet H is set too lean screwed in too far the engine speed will be too high and cause engine damage Do not let the engine run at full speed for more than 10 seconds Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly Iih o 1 e Note that the engine should not be under load when you adjust the high speed jet H You should therefore remove the cutting attachment nut support flange and
12. EM AM49 Champion RCJ 6Y 0 02 0 5 Zama C1Q 1 06 0 5 Weight Weight without fuel cutting attachment and guard Lbs kg 9 9 4 5 Sound levels see note 1 Equivalent sound pressure level at the users ear measured according to ANSI B175 3 1997 dB A min max PARO Vibration levels Vibration levels at handles measured according to ANSI B175 3 1997 m s At idle left right handles min 1 7 1 5 At idle left right handles max 3 9 3 At max speed left right handles min 3 0 9 2 At max speed left right handles max 7 2 9 8 NOTE Noise pressure at the users ear and vibration on the handles are measured with all the machine s approved cutting equipment fitted The table indicates the highest and lowest values Note 1 Equivalent noise pressure level is calculated as the time weighted energy total for noise pressure levels under various working conditions with the following time distribution 1 2 idle and 1 2 max speed Approved accessories Type Cutting attachment guard Art no Arbor shaft thread M10 E O Plastic blades Tricut 300 mm 503 93 42 02 Grass 255 4 1 O 255 4 teeth 503 93 42 02 Grass blade grass cutter Grass 255 8 1 O 250 8 teeth 503 93 42 02 Superauto II 1 503 97 71 01 503 93 42 02 Trimmy H II 1 503 97 71 01 503 93 42 02 Trimmy Hit 1 503 97 71 01 503 93 42 02 Trimmer head Trimmy Hit Pro 503 97 71 01 503 93 42 02 T35 135 503 97 71 01 503 93 42 02 1151472 95 Rev 1 2009 01 16 Engl
13. ING AND STOPPING Check before starting ne en 15 Starting and stopping nn 15 WORKING TECHNIQUES General working instructions 17 MAINTENANCE Carburetor preclinici ani 20 VE Re RETE EE RR TARE ETRO 21 Cooling System een 22 A 22 AA 22 Bevel gear nes een 23 Maintenance schedule pp 24 TECHNICAL DATA Technical data ia 25 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS 26 1151472 95 Rev 1 2009 01 16 Note the following before starting Please read the operators manual carefully Maintenance replacement or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual WARNING Long term exposure to noise can result in permanent hearing impairment So always use approved hearing protection WARNING Under no circumstances may the design of the machine be modified without the permission of the manufacturer Always use genuine accessories Non authorized modifications and or accessories can result in serious personal injury or the death of the operator or others Your warranty may not cover damage or liability caused by the use of non authorized accessories or replacement parts WARNING A clearing saw brushcutter or trimmer can be dangerous if used incorrectly or carelessly and can cause serious or fatal injury to the operator or others
14. Operator s manual EPA 3 26R x series Please read the operator s manual carefully and make sure you understand the instructions before using the machine English KEY TO SYMBOLS Symbols WARNING Clearing saws brushcutters and trimmers can be dangerous Careless or incorrect use can result in serious or fatal injury to the operator or others It is extremely important that you read and understand the contents of the operator s manual Please read the operators manual carefully and make sure you understand the instructions before using the machine Always wear e A protective helmet where there is a risk of falling objects e Approved hearing protection e Approved eye protection Max speed of output shaft rpm max 10000 rpm CE gt Watch out for thrown objects and ricochets The operator of the machine must ensure while working that no persons or animals come closer than 15 metres Machines fitted with saw blades or grass blades can be thrown violently to the side 0 when the blade comes into contact with a fixed object This is called blade thrust The AS blade is capable of amputating an arm or E leg Always keep people and animals at least 15 metres from the machine Arrows which show limits for handle positioning Always wear approved protective gloves Wear sturdy non slip boots Only use non metallic flexible cutting attachments i e trimmer heads with trimmer cord 2 English
15. act of this type can cause damage and wear to the trimmer head 18 English 1151472 95 Rev 1 2009 01 16 WORKING TECHNIQUES Sweeping Thefaneffectofthe rotating cord can be used for quick and easy clearing up Hold the cord parallel to and above the area to be swept and move the tool to and fro e When cutting and sweeping you should use full throttle to obtain the best results 1151472 95 Rev 1 2009 01 16 English 19 MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions After the engine has used 8 10 tanks of fuel the engine will be run in To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running in period ask your dealer service workshop who will have a rev counter at their disposal to adjust your carburettor WARNING The complete clutch cover and shaft must be fitted before the machine is started otherwise the clutch can come loose and cause personal injury Function EAG The carburetor governs the engine s speed via the throttle control Air and fuel are mixed in the carburetor The air fuel mixture is adjustable Correct adjustment is essential to get the best performance from the machine The setting of the carburetor means that the engine is adapted to local conditions for example the climate altitude fuel and the type of 2 stroke oil e The car
16. aighten a twisted blade so that it can be reused Only use original blades of the specified type 10 English Trimmer head IMPORTANT Always ensure the trimmer cord is wound tightly and evenly around the drum otherwise the machine will generate harmful vibration e Only use the recommended trimmer heads and trimmer cords These have been tested by the manufacturer to suit a particular engine size This is especially important when a fully automatic trimmer head is used Only use the recommended cutting attachment See the chapter on Technical data Z LU N e Smaller machines generally require small trimmer heads and vice versa This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared e The length of the cord is also important A longer cord requires greater engine power than a shorter cord of the same diameter e Make sure that the cutter on the trimmer guard is intact This is used to cut the cord to the correct length e To increase the life of the cord it can be soaked in water for a couple of days This will make the line tougher so that it lasts longer 1151472 95 Rev 1 2009 01 16 ASSEMBLY Fitting the J handle Assembling the cutting equipment e Clip the loop handle onto the shaft Note that the loop handle must be fitted between the arrows on the shaft WARNING When fitting the
17. attachment CAUTIONI Do not use the machine unless you are able to call for help in the event of an accident Inspect the working area Remove all loose objects such as stones broken glass nails steel wire string etc that could be thrown out or become wrapped around the cutting attachment Do not use the machine in bad weather such as dense fog heavy rain strong wind intense cold etc Working in bad weather is tiring and often brings added risks such as icy ground unpredictable felling direction etc Make sure you can move and stand safely Check the area around you for possible obstacles roots rocks branches ditches etc in case you have to move suddenly Take great care when working on sloping ground v A y Keep a good balance and a firm foothold 1151472 95 Rev 1 2009 01 16 7 Keep the cutting attachment below waist level 8 Switch off the engine before moving to another area Fit the transport guard before carrying or transporting the equipment any distance 9 Never put the machine down with the engine running unless you have it in clear sight WARNING Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is running or the cutting equipment is rotating as this can result in serious injury Stop the engine and cutting equipment before you remove material that has wound around the blade shaft as otherwise there is a risk of
18. buretor has three adjustment controls L Low speed jet H High speed jet T Idle adjustment screw e The Land H jets are used to adjust the supply of fuel to match the rate that air is admitted which is controlled with the throttle If they are screwed clockwise the air fuel ratio becomes leaner less fuel and if they are turned anti clockwise the ratio becomes richer more fuel A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed e The T screw regulates the throttle setting at idle speed If the T screw is turned clockwise this gives a higher idle speed turning it anti clockwise gives a lower idle speed Basic setting e The basic carburetor settings are adjusted during testing at the factory The basic setting is richer than the optimal setting and should be maintained for the first few hours the machine is in use The carburettor should then be finely adjusted Fine adjustment should be carried out by a skilled technician 20 English CAUTION If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti clockwise until the cutting attachment stops Rec idle speed 2700 rpm Recommended max speed See the Technical data section WARNING If the idle speed cannot be adjusted so that the cutting attachment stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired
19. chments not specifically recommended by HUSQVARNA 1151472 95 Rev 1 2009 01 16 English 23 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine Most of the items are described in the Maintenance section The user must only carry out the maintenance and service work described in this manual More extensive work must be carried out by an authorised service workshop Daily maintenance Weekly maintenance Monthly Maintenance malntenance Clean the outside of the machine Make sure the throttle trigger lock and the throttle function correctly from a safety point of view Check that the stop switch works correctly Check that the cutting attachment does not rotate at idle Clean the air filter Replace if necessary Check that the guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is cracked Check that the trimmer head is undamaged and not cracked Replace the trimmer head if necessary Check that the locking nut of the cutting equipment is tighten correctly Check that nuts and screws are tight Check that there are no fuel leaks from the engine tank or fuel lines Check the starter and starter cord Check that the vibration damping elements are not damaged Clean the outside of the spark plug Remove it and check the electrode gap Adjust the gap to 0 5 mm 20 or replace the spark plug Check that
20. ct exhaust fumes away from the user A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases In countries that have a warm and dry climate there is a significant risk of fire We therefore fit certain mufflers with a spark arrestor screen Check whether the muffler on your machine is fitted with this kind of screen For mufflers it is very important that you follow the instructions on checking maintaining and servicing your machine Never use a machine that has a faulty muffler Regularly check that the muffler is securely attached to the machine 1151472 95 Rev 1 2009 01 16 GENERAL SAFETY PRECAUTIONS If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly A blocked screen will cause the engine to overheat and may lead to serious damage WARNING Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in burns to the skin Remember the risk of fire WARNING The inside of the muffler contain chemicals that may be carcinogenic Avoid contact with these elements in the event of a damaged muffler WARNING Bear in mind that The exhaust fumes from the engine are hot and may contain sparks which can start a fire Never start the machine indoors or near combustible material A locking nut is used to secure some types o
21. e oil intended for four stroke engines e Mixing ratio 1 50 2 with HUSQVARNA two stroke oil Two stroke oil litre Gasoline litre 2 1 50 1 50 ii o o gt aa oo 2 1 2 6 1 2 English 13 FUEL HANDLING Mixing Always mix the gasoline and oil in a clean container intended for fuel Always start by filling half the amount of the gasoline to be used Then add the entire amount of oil Mix shake the fuel mixture Add the remaining amount of gasoline Mix shake the fuel mixture thoroughly before filling the machine s fuel tank Do not mix more than one month s supply of fuel at a time If the machine is not used for some time the fuel tank should be emptied and cleaned WARNING The catalytic converter muffler gets very hot during and after use This also applies during idling Be aware of the fire hazard especially when working near flammable substances and or vapours 14 English Fueling Pe WARNING Taking the following precautions will lessen the risk of fire Do not smoke or place hot objects near fuel Always shut off the engine before refuelling Always stop the engine and let it cool for a few minutes before refuelling When refuelling open the fuel cap slowly so that any excess pressure is released gently Tighten the fuel cap carefully after refuelling Always move the machine away from the refuelling area before starting Clean the area around the fue
22. empted by CARB or EPA may not be used The use of any non exempted add on or modified parts will be grounds for disallowing a warranty claim Husqvarna Forest amp Garden will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part HOW TO FILE A CLAIM If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized servicing dealer or call Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com WHERE TO GET WARRANTY SERVICE Warranty services or repairs are provided through all Husqvarna Forest amp Garden authorized servicing dealers MAINTENANCE REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of the manufacturer MAINTENANCE STATEMENT The owner is responsible for the performance of all required maintenance as defined in the operators manual 1151472 95 Rev 1 2009 01 16 English 27 E 4 A Super Auto II Super Auto Il 1 1151472 95 Rev 1 2009 01 16 JE LO A LI 1151472 95 Rev 1 2009 01 16 1151472 95 Rev 1 2009 01 16 Trimmy Hit 1151472 95 Rev 1 2009 01 16 O pe a I gt E gt G
23. equipment its purpose and how checks and maintenance should be carried out to ensure that it operates correctly See the What is what section to locate where this equipment is positioned on your machine The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and or repairs are not carried out professionally If you need further information please contact your nearest servicing dealer IMPORTANT All servicing and repair work on the machine requires special training This is especially true of the machine s safety equipment If your machine fails any of the checks described below you must contact your service agent When you buy any of our products we guarantee the availability of professional repairs and service If the retailer who sells your machine is not a servicing dealer ask him for the address of your nearest service agent WARNING Never use a machine with faulty safety equipment The machine s safety equipment must be checked and maintained as described in this section If your machine fails any of these checks contact your service agent to get it repaired Throttle lockout The throttle lockout is designed to prevent accidental operation of the throttle control When you press the lock A i e when you grasp the handle it releases the throttle control B When you release the handle the throttle control and the
24. equipped so as to conform with all applicable regulations adopted by EPA and CARB and is free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty must be performed at no charge to the owner at a warranty station Warranty services or repairs will be provided at all Husqvarna Forest amp Garden distribution centers that are franchised to service the subject engines Throughout the emissions warranty period of two years Husqvarna Forest amp Garden must maintain a supply of warranted parts sufficient to meet the expected demand for such parts WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance schedule is warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part will be repaired or replaced by Husqvarna Forest amp Garden at no cost Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part Any warranted part that is not scheduled for replacement as required in the maintenance schedule is warranted for two years If any such part fails during the period of warranty coverage it will be repaired and replaced by Husqvarna Fo
25. et the left hand side of the blade between 8 and 12 oclock do the cutting e The cord wears quicker and must be fed forward more often when working against stones brick concrete metal fences etc than when coming into contact with trees and wooden fences e When trimming and clearing you should use less than full di ISO Ag U eee throttle so that the cord lasts longer and to reduce the grass will collect in a line which makes it easier to collect wear on the trimmer head e g by raking e Try to work rhythmically Stand firmly with your feet apart Cutting Move forward after the return stroke and stand firmly again O e Let the support cup rest lightly against the ground It is used to protect the blade from hitting the ground The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower Keep the cord parallel to the ground when cutting Avoid pressing the trimmer head against the ground as this can ruin the lawn and 1 Always work at full throttle damage the tool e Reduce the risk of material wrapping around the blade by following these instructions 2 Avoid the previously cut material during the return stroke e Stop the engine unclip the harness and place the WY Whi n i i oo machine on the ground before you start to collect the cut material Do not allow the trimmer head to constantly come into contact with the ground during normal cutting Constant cont
26. f cutting attachment When fitting tighten the nut in the opposite direction to the direction of rotation of the cutting attachment To remove it undo the nut in the same direction as the cutting attachment rotates CAUTION The nut has a left hand thread When loosening and tightening the saw blade nut there is a risk of injury from the teeth of the saw blade You should therefore always ensure that your hand is shielded by the blade guard when doing this Always use a socket spanner with a shaft that is long enough to allow this The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut The nylon lining inside the locking nut must not be so worn that you can turn it by hand The lining should offer a resistance of at least 1 5 Nm The nut should be replaced after it has been put on approx 10 times 1151472 95 Rev 1 2009 01 16 Cutting equipment This section describes how to choose and maintain your cutting equipment in order to e Reduce the risk of blade thrust e Obtain maximum cutting performance Extendthe life of cutting equipment IMPORTANT Only use cutting attachments with the guards we recommend See the chapter on Technical data Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter Keep the teeth of the blade correctly sharpened Follow our recommendations Also refer
27. injury The bevel gear can get hot during use and may remain so for a while afterwards You could get burnt if you touch it WARNING Watch out for thrown objects Always wear approved eye protection Never lean over the cutting attachment guard Stones rubbish etc can be thrown up into the eyes causing blindness or serious injury Keep unauthorised persons at a distance Children animals onlookers and helpers should be kept outside the safety zone of 15 m Stop the machine immediately if anyone approaches Never swing the machine around without first checking behind you to make sure no one is within the safety zone Basic working techniques Always slow the engine to idle speed after each working operation Long periods at full throttle without any load on the engine can lead to serious engine damage WARNING Sometimes branches or grass get caught between the guard and cutting attachment Always stop the engine before cleaning English 17 WORKING TECHNIQUES WARNING Machines fitted with saw blades Grass trimming with a trimmer head or grass blades can be thrown violently to the side when the blade comes into contact with a fixed object This is called blade thrust A blade thrust can be violent enough to cause the machine and or operator to be Trimming propelled in any direction and possibly lose control of the machine Blade thrust can occur without warning if the machine snags e Hold the
28. ipped with a special spark arrestor screen If your machine has this type of muffler you should clean the screen at least once a week This is best done with a wire brush On mufflers without a catalytic converter the screen should be cleaned weekly or replaced if necessary On mufflers fitted with a catalytic converter the screen should be checked and if necessary cleaned monthly If the screen is damaged it should be replaced If the screen is frequently blocked this can be a sign that the performance of the catalytic converter is impaired Contact your dealer to inspect the muffler A blocked screen will cause the machine to overheat and result in damage to the cylinder and piston CAUTION Never use a machine with a defective muffler WARNING Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in burns to the skin Remember the risk of fire English 21 MAINTENANCE Cooling system u To keep the working temperature as low as possible the machine is equipped with a cooling system The cooling system consists of 1 Air intake on the starter 2 Fins on the flywheel 3 Cooling fins on the cylinder 4 Cylinder cover directs cold air over the cylinder Clean the cooling system with a brush once a week more often in demanding conditions A dirty or blocked cooling system results in the
29. ish 25 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA U S Environmental Protection Agency CARB California Air Resources Board Environment Canada and Husqvarna Forest amp Garden are pleased to explain the emissions control system s warranty on your 2009 and later small off road engine In U S and Canada new equipment that use small off road engines must be designed built and equipped to meet the applicable Federal or Californian stringent anti smog standards Husqvarna Forest amp Garden must warrant the emissions control system on your small off road engine for the period listed below provided there has been no abuse neglect or improper maintenance of your equipment Your emissions control system may include parts such as the carburetor ignition system catalytic converter fuel tank filters and other associated components Also included may be hoses belts connectors sensors and other emission related assemblies Where a warrantable condition exists Husqvarna Forest amp Garden will repair your small off road engine at no cost to you including diagnosis parts and labor MANUFACTURER S WARRANTY COVERAGE The emissions control system is warranted for two years If any emissions related part on your equipment is defective the part will be repaired or replaced by Husqvarna Forest amp Garden OWNER S WARRANTY RESPONSIBILITIES e As the small off r
30. l cap Contamination in the tank can cause operating problems Ensure that the fuel is well mixed by shaking the container before filling the tank una um Min 3 a 10 ft 1151472 95 Rev 1 2009 01 16 STARTING AND STOPPING Check before starting e Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth Discard a blade if cracks are found Ov e Check that the support flange is not cracked due to fatigue or due to being tightened too much Discard the support flange if it is cracked e Ensure the locking nut has not lost its captive force The nut lock should have a locking force of at least 1 5 Nm The tightening torque of the locking nut should be 35 50 Nm e Check that the blade guard is not damaged or cracked Replace the blade guard if it is exposed to impact or is cracked e Check that the trimmer head and trimmer guard are not damaged or cracked Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked e Never use the machine without a guard nor with a defective guard e All covers must be correctly fitted and undamaged before you start the machine 1151472 95 Rev 1 2009 01 16 Starting and stopping WARNING The complete clu
31. lug cap and ignition lead are undamaged to avoid the risk of electric shock The machine operator must ensure that no people or animals come closer than 15 metres while working When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres WARNING The ignition system of this machine produces an electromagnetic field during operation This field may under some circumstances interfere with pacemakers To reduce the risk of serious or fatal injury we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine WARNING Running an engine in a confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning WARNING Never allow children to use or be in the vicinity of the machine As the machine is equipped with a spring loaded stop switch and can be started by low speed and force on the starter handle even small children under some circumstances can produce the force necessary to start the machine This can mean a risk of serious personal injury Therefore remove the spark plug cap when the machine is not under close supervision 6 English Personal protective equipment IMPORTANT A clearing saw brushcutter or trimmer can be dangerous if used incorrectly or carelessly and can cause serious or fatal injury to the operator or others It
32. machine overheating which causes damage to the piston and cylinder Spark plug Plo The spark plug condition is influenced by e Incorrect carburetor adjustment e An incorrect fuel mixture too much or incorrect type of oil e Adirty air filter These factors cause deposits on the spark plug electrodes which may result in operating problems and starting difficulties If the machine is low on power difficult to start or runs poorly at idle speed always check the spark plug first before taking any further action If the spark plug is dirty clean it and check that the electrode gap is 0 020 inch 0 5 mm The spark plug should be replaced after about a month in operation or earlier if necessary CAUTION Always use the recommended spark plug type Use of the wrong spark plug can damage the piston cylinder 22 English Air filter ope The air filter must be regularly cleaned to remove dust and dirt in order to avoid e Carburettor malfunctions Starting problems e Loss of engine power e Unnecessary wear to engine parts e Excessive fuel consumption Clean the filter every 25 hours or more regularly if conditions are exceptionally dusty Cleaning the air filter Remove the air filter cover and take out the filter Wash it clean in warm soapy water Ensure that the filter is dry before refitting it An air filter that has been in use for a long time cannot be cleaned completely The filter m
33. mage the machine CAUTION Do not put any part of your body in marked area Contact can result in burns to the skin or electrical shock if the spark plug cap has been damaged Always use gloves Do not use a machine with damaged spark plug cap Stopping Stop the engine by switching off the ignition CAUTION CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance 16 English 1151472 95 Rev 1 2009 01 16 WORKING TECHNIQUES General working instructions 6 Always hold the machine with both hands Hold the machine on the right side of your body IMPORTANT This section describes the basic safety precautions for working with clearing saws and trimmers If you encounter a situation where you are uncertain how to proceed you should ask an expert Contact your dealer or your service workshop Avoid all usage which you consider to be beyond your capability You must understand the difference between forestry clearing grass clearing and grass trimming before use Basic safety rules 1 Look around you To ensure that people animals or other things cannot affect your control of the machine To ensure that people animals etc do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting
34. nts of fuel even small inaccuracies can drastically affect the ratio of the mixture WARNING Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin For this reason observe caution when handling fuel and make sure there is adequate ventilation 1151472 95 Rev 1 2009 01 16 Gasoline AE CAUTION Always use a quality gasoline oil mixture with an octane rating of at least 87 octane RON MON 2 If your machine is equipped with a catalytic converter see chapter on Technical data always use a good quality unleaded gasoline oil mixture Leaded gasoline will destroy the catalytic converter Use low emission gasoline also known as alkylate gasoline if it is available This engine is certified to operate on unleaded gasoline e The lowest recommended octane grade is 87 RON MON 2 If you run the engine on a lower octane grade than 87 so called knocking can occur This gives rise to a high engine temperature and increased bearing load which can result in serious engine damage e When working at continuous high revs a higher octane rating is recommended Two stroke oil e For best results and performance use HUSQVARNA two stroke engine oil which is specially formulated for our air cooled two stroke engines Never use two stroke oil intended for water cooled engines sometimes referred to as outboard oil rated TCW e Never us
35. oad engine owner you are responsible for performance of the required maintenance listed in your operator s manual Husqvarna Forest amp Garden recommends that you retain all receipts covering maintenance on your small off road engine but Husqvarna Forest amp Garden cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance As the small off road engine owner you should however be aware that Husqvarna Forest amp Garden may deny you warranty coverage if your small off road engine or a part has failed due to abuse neglect or improper maintenance or unapproved modifications e You are responsible for presenting your small off road engine to a Husqvarna Forest amp Garden distribution center or service center as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized servicing dealer or call Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com WARRANTY COMMENCEMENT DATE The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser 26 English LENGTH OF COVERAGE Husqvarna Forest amp Garden warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is designed built and
36. ocking nut 3 Bevel gear 18 Support flange 4 Cutting attachment guard 19 Drive disc 5 Shaft 20 Socket spanner 6 Loop handle 21 Operators manual 7 Throttle control 22 Allen key 8 Stop switch 23 Locking pin 9 Throttle lockout 24 Support cup 10 Cylinder cover 25 Blade 11 Starter handle 26 Transport guard 12 Fuel tank 27 J handle 13 Choke control 28 Support eyes for harness 14 Air purge 29 Harness 15 Air filter cover 30 Spark plug cap and spark plug 1151472 95 Rev 1 2009 01 16 English 5 GENERAL SAFETY PRECAUTIONS Important IMPORTANTI The machine is only designed for trimming grass The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data Never use the machine if you are tired if you have drunk alcohol or if you are taking medication that could affect your vision your judgement or your co ordination Wear personal protective equipment See instructions under the heading Personal protective equipment Never use a machine that has been modified in any way from its original specification Never use a machine that is faulty Carry out the checks maintenance and service instructions described in this manual Some maintenance and service measures must be carried out by trained and qualified specialists See instructions under the heading Maintenance All covers guards and handles must be fitted before starting Ensure that the spark p
37. racked Always use the recommended guard for the cutting attachment you are using See chapter on Technical data WARNING Never use a cutting attachment without an approved guard See the chapter on Technical data If an incorrect or faulty guard is fitted this can cause serious personal injury Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration See instructions under the heading Cutting equipment The machine s vibration damping system reduces the transfer of vibration between the engine unit cutting equipment and the machine s handle unit Regularly check the vibration damping units for cracks or deformation 8 English Check that the vibration damping element is undamaged and securely attached WARNING Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation Contact your doctor if you experience symptoms of overexposure to vibration Such symptoms include numbness loss of feeling tingling pricking pain loss of strength changes in skin colour or condition These symptoms normally appear in the fingers hands or wrists The risk increases at low temperatures Muffler The muffler is designed to keep noise levels to a minimum and to dire
38. rest amp Garden at no cost Any such part repaired or replaced under the warranty is warranted for the remaining warranty period Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years A statement in such written instructions to the effect of repair or replace as necessary will not reduce the period of warranty coverage Any such part repaired or replaced under warranty will be warranted for the remaining warranty period DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station CONSEQUENTIAL DAMAGES Husqvarna Forest amp Garden is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts Intake pipe airfilter holder and carburetor bolts Airfilter and fuelfilter covered up to maintenance schedule Spark Plug covered up to maintenance schedule Ignition Module Muffler with catalytic converter N U A W N Fuel tank 1151472 95 Rev 1 2009 01 16 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT WHAT IS NOT COVERED All failures caused by abuse neglect or improper maintenance are not covered ADD ON OR MODIFIED PARTS Add on or modified parts that are not ex
39. s area Husqvarna is working today Today Husqvarna is one of the leading manufacturers in the world of forest and garden products with quality as our highest priority We develop manufacture and market high quality motor driven products for forestry and gardening as well as for building and construction industry Your purchase gives you access to professional help with repairs and service whenever this may be necessary If the retailer who sells your machine is not one of our authorized dealers ask for the address of your nearest servicing dealer It is our wish that you will be satisfied with your product and that it will be your companion for a long time Think of this operator s manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you ever lend or sell this machine make sure that the borrower or buyer gets the operator s manual so they will also know how to properly maintain and use it Thank you for using a Husqvarna product Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice For customer assistance contact us at our website www usa husqvarna com 4 English 1151472 95 Rev 1 2009 01 16 WHAT IS WHAT What is what on the trimmer 1 Trimmer head 16 Handle adjustment 2 Grease filler cap bevel gear 17 L
40. tch cover and shaft must be fitted before the machine is started otherwise the clutch can come loose and cause personal injury Always move the machine away from the refuelling area before starting Place the machine on a flat surface Ensure the cutting attachment cannot come into contact with any object Make sure no unauthorised persons are in the working area otherwise there is a risk of serious personal injury The safety distance is 15 metres Starting Primer bulb Press the air purge repeatedly until fuel begins to fill the bulb The bulb need not be completely filled WARNING When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately Hold the body of the machine on the ground using your left hand CAUTION Not with your foot Grip the starter handle slowly pull out the cord with your right hand until you feel some resistance the starter pawls grip now quickly and powerfully pull the cord Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts When the engine starts return choke control to run position and apply full throttle the throttle will automatically disengage from the Start setting English 15 STARTING AND STOPPING CAUTION Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended This can da
41. th the corresponding hole in the gear housing Insert the locking pin C in the hole to lock the shaft Place the blade D support cup E and support flange F on the output shaft 12 English Fit the nut G The nut must be tightened to a torque of 35 50 Nm 3 5 5 kpm Use the socket spanner in the tool kit Hold the shaft of the spanner as close to the blade guard as possible To tighten the nut turn the spanner in the opposite direction to the direction of rotation Caution left hand thread Fitting other guards and cutting attachments Fit the correct trimmer guard A for use with the trimmer head Hook the trimmer guard combination guard onto the fitting on the shaft and secure with the bolt L A Fit the drive disc B on the output shaft Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing Insert the locking pin C in the hole to lock the shaft Screw on the trimmer head plastic blades H in the opposite direction to the direction of rotation To dismantle follow the instructions in the reverse order 1151472 95 Rev 1 2009 01 16 FUEL HANDLING Fuel safety Never start the machine 1 If you have spilled fuel on it Wipe off the spillage and allow remaining fuel to evaporate 2 If you have spilled fuel on yourself or your clothes change your clothes Wash any part of your body that has come in contact with fuel
42. the hole to lock the shaft e To fit the trimmer head first separate the two halves see diagram Proceed as follows 1151472 95 Rev 1 2009 01 16 English 11 ASSEMBLY Insert a finger into the centre hole of the cover 1 while grasping the cover with your other fingers Using the index finger and thumb of your other hand release the two catches J that engage in the cut outs in the bottom half K Pull apart the trimmer head grasping the cover firmly Place the cover I and the support flange F on the output shaft Fit the nut G The nut must be tightened to a torgue of 35 50 Nm 3 5 5 kpm Use the socket spanner in the tool kit Hold the shaft of the spanner as close to the blade guard as possible To tighten the nut turn the spanner in the opposite direction to the direction of rotation Caution left hand thread Fit the bottom half of the trimmer head K to the cover 1 by pressing them together with the cut outs on the bottom half aligned with the catches on the cover To dismantle follow the instructions in the reverse order Fitting the blade guard combination guard grass blade and grass cutter Hook the blade guard combination guard A onto the fitting on the shaft and secure with the bolt CAUTION Use the recommended blade guard See the Technical data section ey G Fit the drive disc B on the output shaft Turn the blade shaft until one of the holes in the drive disc aligns wi
43. throttle lockout both move back to their original positions This movement is controlled by two independent return springs This arrangement means that the throttle control is automatically locked at the idle setting 1151472 95 Rev 1 2009 01 16 Make sure the throttle control is locked at the idle setting when the throttle lockout is released Press the throttle lockout and make sure it returns to its original position when you release it Check that the throttle control and throttle lockout move freely and that the return springs work properly See instructions under the heading Start Start the machine and apply full throttle Release the throttle and check that the cutting attachment stops and remains at a standstill If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting must be checked See instructions under the heading Maintenance Stop switch Use the stop switch to switch off the engine Start the engine and make sure the engine stops when you move the stop switch to the stop setting English GENERAL SAFETY PRECAUTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator The guard also protects the operator from accidental contact with the cutting attachment Check that the guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is c
44. trimmer head just above the ground at an angle It is the end of the cord that does the work Let the cord work at its own pace Never press the cord into the area stalls or binds Blade thrust is more likely to to be cut occur in areas where it is difficult to see the material being cut Avoid cutting with the area of the blade between the 12 o clock and 3 o clock positions Because of the speed of rotation V of the blade blade thrust can occur if you attempt to cut thick stems with this area of e The cord can easily remove grass and weeds up against the blade walls fences trees and borders however it can also damage sensitive bark on trees and bushes and damage fence posts PINA MAN HY as N Grass clearing using a grass blade e Reduce the risk of damaging plants by shortening the cord to 10 12 cm and reducing the engine speed Clearing e Grass blades and grass cutters must not be used on woody stems e The clearing technique removes all unwanted vegetation Keep the trimmer head just above the ground and tilt it Let e A grass blade is used for all types of tall or coarse grass the end of the cord strike the ground around trees posts The grass is cut down with a sideways swinging statues and the like CAUTION This technique increases movement where the movement from right to left is the the wear on the cord clearing stroke and the movement from left to right is the return stroke L
45. ust therefore be replaced with a new one at regular intervals A damaged air filter must always be replaced If the machine is used in dusty conditions the air filter should be soaked in oil See instructions under the heading Oiling the air filter Oiling the air filter i m Always use HUSQVARNA filter oil art no 531 00 92 48 The filter oil contains a solvent to make it spread evenly through the filter You should therefore avoid skin contact Put the filter in a plastic bag and pour the filter oil over it Knead the plastic bag to distribute the oil Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine Never use common engine oil This would drain through the filter quite quickly and collect in the bottom 1151472 95 Rev 1 2009 01 16 MAINTENANCE Bevel gear The bevel gear is filled with the right quantity of grease at the factory However before using the machine you should check that the bevel gear is filled three guarters full with grease Use HUSQVARNA special grease The grease in the bevel gear does not normally need to be changed except if repairs are carried out vs CAUTION Use only HUSQVARNA replacement parts Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others Your warranty does not cover damage or liability caused by the use of accessories and or atta
Download Pdf Manuals
Related Search